Tripp Lite | AVS30D Automatic Voltage Switch | Owner's Manual | Tripp Lite AVS30D Automatic Voltage Switch Owner's Manual

Tripp Lite AVS30D Automatic Voltage Switch Owner's Manual
Owner’s Manual
Automatic Voltage
Switch
Model: AVS30D
Introduction
The AVS30D Automatic Voltage Switch is a 30 amp rated automatic voltage switch
that protects appliances from high voltages, low voltages (including brownouts),
power surges, spikes and lighting. It does this by switching off connected equipment
if the power flowing to it goes outside preset limits, and will reconnect automatically
when power returns to normal (except in the case of an overload condition). There
will be a delay before the reconnection to ensure power stability.
Ce manuel est disponible en français sur le site Web de Tripp Lite : www.tripplite.com
Русскоязычная версия настоящего руководства представлена на веб-сайте компании
Tripp Lite по адресу: www.tripplite.com
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
14-01-250-933301.indd 1
Copyright © 2014 Tripp Lite. All rights reserved.
1
3/13/2014 12:18:36 PM
Product Overview
8
6
5
3
4
7
1
7
2
1 Input Terminal Connects mains power.
2 Output Terminal Connects to appliance wiring.
3 F1 & F2 Program Buttons Using the two buttons, you can set the output
4 over/under voltage, overload protection value, browse settable parameters and
change digital display mode. During normal operation, you can press F2 to
display the load. After 3 seconds, the switch returns to the voltage display.
5 Voltage LED Illuminates when the digital display shows voltage.
6 Load LED Illuminates when the digital display shows the load in watts.
14-01-250-933301.indd 2
2
3/13/2014 12:18:37 PM
Product Overview
7 Cord Strain Reliefs Reduces strain on mains and appliance cables.
8 Digital Display Shows voltage, wattage, status and settings.
A) U-H Output Overvoltage Protection Status
When output voltage exceeds the preset limit and doesn’t return to within
the preset limits after 1 second, your equipment will be disconnected by
the switch. U-H will flash on the display every .5 seconds as long as the
overvoltage condition exists.
B) U-L Output Undervoltage Protection Status
When output voltage goes lower than the preset limit and doesn’t return to
within the preset limits after 1 second, your equipment will be disconnected
by the switch. U-L will flash on the display every .5 seconds as long as the
undervoltage condition exists.
C) P-H Overload Protection Status
When the load exceeds the preset range (nominally 110-120%) and lasts
longer than 6 seconds (within this 6 seconds no action will be taken by the
AVS30D), the switch will disconnect from power. P-H will flash on the display
every .5 seconds as long as the overload condition exists.
When the load exceeds the preset range (nominally 150%) and lasts longer
than 1 second, the switch will disconnect from power. P-H will flash on the
display every .5 seconds as long as the overload condition exists.
D) Start Up Delay
When first powered up, the unit will count down a set number of seconds
(default is 6) before monitoring voltage.
E) Parameter Setting Codes
E-0 Delay setting
E-1 Undervoltage protection value setting
E-2 Overvoltage protection value setting
E-3 Overload protection value setting
E-4 Displays output voltage or loading power value after startup
(U= voltage, P= watts)
E-5 Restores default settings
Note: The code and value flash alternately every second while changing settings.
14-01-250-933301.indd 3
3
3/13/2014 12:18:37 PM
Operation
Caution: Don’t use this switch with any device that needs to be
continually powered, as the switch is designed to cut power when
unstable voltages occur.
1) Make sure your load doesn’t exceed the 30 amp rating of the switch.
2) The switch must be wired to the mains supply and the equipment it’s supplying.
Please refer to Connection section for wiring and installation instructions.
3) After the switch is plugged in, it will display a 6 second countdown (default)
before supplying power to your appliance and showing the voltage on the Digital
Display.
4) If the default settings aren’t appropriate for your situation, you can change them
by following the procedure in the Changing Settings section.
Notes:
• We strongly recommend you use the default settings to ensure safe operation of the switch.
• It’s possible to adjust the parameters at any time. Changing the delay setting requires a power cycle
for the new delay to take effect.
Resetting an Overload Fault
The unit doesn’t reset automatically from an overload fault. To manually reset the
unit:
1) Remove the cause of the overload.
2) Press and hold F1 until E-0 appears on the display, then release.
3) Wait for the unit to reset. It will count down from preset and turn the load back
on.
14-01-250-933301.indd 4
4
3/13/2014 12:18:37 PM
Changing Settings
Press and hold F1 for three seconds to enter settings mode.
Setting Codes: E-0 will be displayed.
(See Switch Settings chart for code explanations)
Press F1 to cycle through the available codes.
Press F2 to select the code you wish to change.
Press F2 to adjust the value (the code and value will flash alternately every
second). Each value changes by a certain increment every time you press F2
(See Switch Settings chart).
Press F1 to confirm the value.
Don’t press anything for 10 seconds to exit and save the settings.
Switch Settings
Code
Increment
# of
Increments
6-120
seconds
6 seconds
20
180V
120V-200V
5V
16
Overvoltage
Protection
255V
210V-270V
5V
12
Overload
Protection
3000W
800W-4800W
800W
6
Item
Default
Delay Setting
6 seconds
E-1
Undervoltage
Protection
E-2
E-3
E-0
E-4
E-5
Digital Display
Restore Defaults
Settable
Range
Shows output voltage or loading power value after
startup (U= voltage, P= watts)
Restores all default settings. Unit will display defaults
once confirmed, then reset and count down.
Note: An “A” on the display indicates the load exceeds 1000 watts (e.g. 2A5 =2500W)
14-01-250-933301.indd 5
5
3/13/2014 12:18:37 PM
Connection
DANGER! RISK OF ELECTRIC SHOCK!
All wiring should be performed by a qualified electrician in
accordance with all applicable electrical and safety codes. All
wiring must comply with local ordinances and must be a proper
type and size to support 30 amps. Incorrect wiring may damage
the switch severely and cause serious personal injury and
property damage.
Connection Warnings
• The user must determine if this device is suitable for the intended application.
• The device should be installed indoors only.
• This device is not intended to serve as overcurrent protection. Overcurrent
protection should be provided by the user and present on the input side of the
device.
• Verify that the input source is not live when wiring this device.
• Once installed, never operate the device without the cover in place.
Wiring
1) To get access to the connection terminals, you need to remove the bottom cover.
To do this, remove the two black caps and then remove the two screws. Remove
the bottom cover.
2) Loosen the cord strain reliefs.
3) Insert cable from the mains supply through the left side “input” cable port and
make the screw terminal connections (refer to the Connection Terminals
diagram). DO NOT OVERTIGHTEN SCREW TERMINALS.
4) Insert appliance cable through the right side “output” cable port and make the
screw terminal connections (refer to the Connection Terminals diagram).
5) Tighten the cord strain reliefs, then replace the bottom cover, screws and caps.
Note: Mount the switch to a screw on the wall by using the keyhole slot on the back.
Connection Terminals
14-01-250-933301.indd 6
INPUT
Line to IN:L
Neutral to IN:N
Earth to E
OUTPUT
Line to O:L
Neutral to O:N
Earth to E
6
3/13/2014 12:18:37 PM
Specifications
Current Rating
30 amps
Voltage Rating
230V (220-240V)
Frequency
50/60 Hz
Response Time Over/undervoltage
1 second
Reflex Voltage Over/undervoltage
5~10V
Radio Frequency Interference/Noise Protection
Yes
Spike/Surge Protection (Joules)
380J
Spike/Surge Protection (Amps)
6500KA (8/20us)
Spike/Surge Protection (Response Time)
10 nanoseconds
Dimensions (HxWxD)
205x135x55 mm
Weight
.5 kg
14-01-250-933301.indd 7
7
3/13/2014 12:18:37 PM
Warranty
7-Year Limited Warranty
TRIPP LITE warrants its products to be free from defects in materials and workmanship for a
period of seven (7) years from the date of initial purchase. TRIPP LITE’s obligation under this
warranty is limited to repairing or replacing (at its sole option) any such defective products. To
obtain service under this warranty, you must obtain a Returned Material Authorization (RMA)
number from TRIPP LITE or an authorized TRIPP LITE service center. Products must be returned
to TRIPP LITE or an authorized TRIPP LITE service center with transportation charges prepaid
and must be accompanied by a brief description of the problem encountered and proof of date
and place of purchase. This warranty does not apply to equipment, which has been damaged by
accident, negligence or misapplication or has been altered or modified in any way.
EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid
limitation(s) or exclusion(s) may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS
PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, TRIPP LITE is not
liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment,
loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise.
Regulatory Compliance Identification Numbers
For the purpose of regulatory compliance certifications and identification, your Tripp Lite product
has been assigned a unique series number. The series number can be found on the product
nameplate label, along with all required approval markings and information. When requesting
compliance information for this product, always refer to the series number. The series number
should not be confused with the marketing name or model number of the product.
WEEE Compliance Information for Tripp Lite Customers and Recyclers
(European Union)
Under the Waste Electrical and Electronic Equipment (WEEE) Directive and
implementing regulations, when customers buy new electrical and electronic
equipment from Tripp Lite they are entitled to:
• Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on
the country)
• Send the new equipment back for recycling when this ultimately becomes waste
Use of this equipment in life support applications where failure of this equipment can reasonably
be expected to cause the failure of the life support equipment or to significantly affect its safety
or effectiveness is not recommended. Do not use this equipment in the presence of a flammable
anesthetic mixture with air, oxygen or nitrous oxide.
Tripp Lite follows a policy of continuous improvement. Product specifications are subject to
change without notice.
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
14-01-250-933301.indd 8
8
3/13/2014 12:18:38 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising