Tripp Lite | DMCVW4555X4 | Owner's Manual | Tripp Lite DMCVW4555X4 Owner's Manual

Tripp Lite DMCVW4555X4 Owner's Manual
Owner’s Manual
Heavy-Duty
Quad-Monitor Mobile Video Wall
Model: DMCVW4555X4
55"
MAX
200x200 / 300x300 / 400x200
400x400 / 600x400
132 lb. x 4
(60 kg) x 4
Este manual esta disponible en español en la página de Tripp Lite: www.tripplite.com
Ce manuel est disponible en français sur le site Web de Tripp Lite : www.tripplite.com
Русскоязычная версия настоящего руководства представлена на веб-сайте компании Tripp Lite по адресу: www.tripplite.com
Dieses Handbuch ist in deutscher Sprache auf der Tripp Lite-Website verfügbar: www.tripplite.com
PROTECT YOUR INVESTMENT!
Register your product for quicker service and ultimate peace of mind.
You could also win an ISOBAR6ULTRA surge protector—a $100 value!
www.tripplite.com/warranty
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2019 Tripp Lite. All rights reserved.
1
NOTE: Read the entire instruction manual before you start assembly and installation.
WARNING
• Do not begin the installation until you have read and understood the instructions and warnings contained in this manual. If
you have questions regarding any of the instructions or warnings, please visit www.tripplite.com/support.
• This product was designed to be installed and utilized ONLY as specified in this manual. Improper installation of this product
may cause damage or serious injury.
• This product should only be installed by someone of good mechanical ability, with basic building experience and a full
understanding of this instruction manual.
• Make sure the unit can safely support the combined load of the equipment and all attached hardware and components.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and/or personal injury.
Warranty and Product Registration
5-Year Limited Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of 5 years from the date
of initial purchase. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole discretion.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES
OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES
OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND
CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from
jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since individual applications are
subject to great variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific application.
PRODUCT REGISTRATION
Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice. Photos and illustrations may differ slightly from actual products.
2
Component Checklist
IMPORTANT: Ensure you have received all parts according to the component checklist prior to installing. If any parts are missing
or faulty, visit www.tripplite.com/support for service.
A
Middle Base
(x1)
B
Left Base
(x1)
G
Adapter Bracket
(x8)
K
Connecting Piece
(x2)
C
Right Base
(x1)
H
Plastic Cover
(x4)
L
Top Cover
(x2)
D
Left Cover
(x1)
E
Right Cover
(x1)
F
Universal Plate
(x2)
I
Support Plate
(x4)
M
Cable Clamp
(x16)
J
Column
(x2)
N
Caster Wheel with Brake
(x2)
O
Caster Wheel
(x2)
P
Combo Lock
(x4)
Package A
A-A
3 mm Hex Key
(x1)
A-B
5 mm Hex Key
(x1)
A-C
6 mm Hex Key
(x1)
A-D
Wrench
(x1)
Package M
M-A
M5x14
(x16)
M-B
M6x14
(x16)
M-C
M8x20
(x16)
M-D
M6x30
(x16)
M-E
M8x30
(x16)
M-F
Washer
(x16)
M-G
Small Spacer
(x32)
M-H
Big Spacer
(x16)
Package P
P-A
ST4.2x9.5
(x8)
P-B
M6x20
(x2)
P-C
M8x65
(x8)
P-D
M8x16
(x8)
3
P-E
M8x35
(x8)
P-F
D8 Washer
(x4)
Assembly
1 Assemble the Base
A
C
B
Note: Position base assembly
with wheels facing forward.
M
A-C
Each caster can be adjusted
independently for fine tuning. Using the
wrench (A-D), slightly turn each caster
nut to lower or raise the base.
P-C
A-D
Note: Lock the
brakes on the casters
to avoid any sudden
movements during
installation.
Using M8x65 screws (P-C) and the 6 mm hex key (A-C), attach the left and right base to the middle base.
4
Assembly
2 Attach the Columns to the Base
K
P-F
P-E
A-C
J
S
Insert the two connecting pieces (K) to attach the columns (J) to the base. Use M8x35 screws (P-E), D8 washers (P-F) and the 6 mm
hex key (A-C) to secure the connecting pieces and columns to the base.
3 Install the Covers
D
E
Attach the left cover (D) and right cover (E) to the base.
5
Assembly
4 Install the Support Plates
I
F
Slide the first set of support
plates (I) onto the columns,
making sure the arrow on the
support plates are pointing up.
Slide the second set of support plates (I)
onto the column, making sure the arrows
on the support plates are pointing up.
Allow enough space
between the two
universal plates. Set a
distance of the height
of the display plus
0.2" (5 mm)
X + 0.2” (5 mm)
(X=Height of display)
Keep the
support plates
at the same
level.
A-B
Once the support plate
positions have been
determined, use the 5 mm
hex key (A-B) to secure
them to the columns.
6
Assembly
5 Install the Universal Plates
F
A-D
Slide the universal plates (F) into the support plates,
making sure to align the holes in the universal plates
with the holes in the support plates.
P-B
Use the M6x20 screws (P-B) and wrench (A-D) to secure the universal
plates to the support plates. Do not over-tighten the screws.
P-A
H
Use the ST4.2x9.5 screws
(P-A) to attach the four plastic
covers (H) to each end of the
universal plates.
7
Assembly
6 Install the Top Covers
Using M8x16 screws (P-D) and the
6 mm hex key (A-C), attach the
top covers (L) to the columns.
A-C
P-D
L
7 Install the Adapter Brackets
Top of the
display.
8
Assembly
7a Install the Adapter Brackets
For Flat-Back Screens
M-A / M-B / M-C
M-F
Note: Choose appropriate screws and spacers according to the type of screens.
• Position the adapter brackets as close as possible to the center of the display.
• Screw the adapter brackets onto the display.
• Repeat procedure for the second display.
Tighten all screws, but do not over-tighten.
7b Install the Adapter Brackets
For Recessed-Back Screen
or to Access A/V Inputs
M-C
M-C / M-D / M-E
or M-F
M-F
M-D / M-E
or
M-D / M-E
or
M-F
M-F
M-G
M-G
M-G
M-H
Note: Choose appropriate screws, washers and spacers (if necessary) according to the type of screen.
• Position the adapter brackets as close as possible to the center of the display.
• Screw the adapter brackets onto the display.
• Repeat procedure for the second display.
Tighten all screws, but do not over-tighten.
9
M-H
Assembly
8 Attach the Displays onto the Universal Plates
Note: When installing the displays, make
sure to work from the bottom universal
plate to the top universal plate.
• Using an assistant or mechanical lifting
equipment, carefully lift the display and
pull down the two adapter bracket straps at
the same time. Hook the display’s adapter
brackets over the top of the universal wall
plate. Release the adapter bracket straps to
secure the display to the universal plate.
1 mm
• Repeat procedure for the second, third and
fourth displays.
Use the combo locks (P)
to protect the displays
from tampering and theft.
P
10
Note: Make sure to
leave a 1 mm gap
between both displays.
Assembly
9 Micro-Adjustment
A-B
Note: Adjust the
angle of displays
in the order shown
above.
T
If the display tilts upward, adjust using the 5 mm hex key (A-B), as shown above.
A-B
T
If the display tilts downward, adjust using the 5 mm hex key (A-B), as shown above.
11
Assembly
9 Micro-Adjustment
Up
Down
1
mm
A-B
To move the displays up or down, adjust using the 5 mm hex key (A-B), as shown above.
Note: Make sure to leave a 1 mm gap between the upper and lower displays.
10 Cable Management
M
Insert the cable clamps (M) horizontally into the universal plates’ slots, then turn the cable clamps vertically to secure them.
12
Assembly
10 Cable Management
Run the cables
through the cable
clamps and the
column’s rubber strip.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
• Please visit www.tripplite.com/support if you have any questions.
13
14
15
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
16
19-02-171 93-3951_RevA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising