Tripp Lite | T040-001-DP | Owner's Manual | Tripp Lite T040-001-DP Owner's Manual

Tripp Lite T040-001-DP Owner's Manual
Owner’s Manual
DisplayPort/Mini
DisplayPort Cable Tester
Model: T040-001-DP
Este manual esta disponible en español en la página de Tripp Lite:
www.tripplite.com/support
Ce manuel est disponible en français sur le site Web de Tripp Lite :
www.tripplite.com/support
Русскоязычная версия настоящего руководства
представлена на веб-сайте компании Tripp Lite по адресу:
www.tripplite.com/support
PROTECT YOUR INVESTMENT!
Register your product for quicker service and ultimate peace of mind.
You could also win an ISOBAR6ULTRA surge protector—a $100 value!
www.tripplite.com/warranty
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
10-415-933796-EN.indd 1
Copyright © 2017 Tripp Lite. All rights reserved.
1
11/15/2017 9:42:43 A
Package Contents
• Master Unit
• Carrying Case
• Remote Unit
• Owner’s Manual
Product Features
• All-in-one unit combines a Main Tester with a removable Remote Identifier
• Compatible with DisplayPort versions 1.0 through 1.4
• Fast and accurate verification of DisplayPort and Mini DisplayPort cables
• Displays 19 pin-to-pin wire map and shield connection status to ensure
mapping continuity and proper configuration
• Two adjustable test modes available: Continuity and Sweep
10-415-933796-EN.indd 2
2
11/15/2017 9:42:43 A
Operation
Note: Before testing, insert a 9V battery (not included) and ensure the cable being
tested is not yet connected to the tester.
Testing
Simply connect the desired cable to the unit, then switch the Sweep/OFF/
Continuity button to “Continuity” for sync testing, or “Sweep” for step-bystep testing.
Note: During sync testing, all LEDs illuminate on the wire map at once. During step-bystep testing, the LEDs will illuminate one at a time.
When testing uninstalled patch cable, you can leave the Main Tester and
Remote Identifier connected.
When testing installed cable, you will need to remove the Remote
Identifier from the Main Tester. Connect one end of the cable to the
appropriate connector on the Main Tester, and the other end of the cable to
the appropriate connector on the Remote Identifier.
Note: Upon switching to the desired testing mode, the LEDs on the Main Tester and
Remote Identifier will illuminate to indicate the results.
If testing DisplayPort-to-DisplayPort cables, use “A pin” side numbers
found on both the Main Tester and Remote Identifier. For DisplayPort-to-Mini
DisplayPort and Mini DisplayPort-to-Mini DisplayPort cables, use “C pin” side
numbers found on both the Main Tester and Remote Identifier.
10-415-933796-EN.indd 3
3
11/15/2017 9:42:43 A
Detecting Connections
Note: This product is designed to test cable lengths up to 49 ft. (15 m).
When a cable connection from both ends is detected, the LEDs will
illuminate. Listed below are detected connection examples with diagrams
showing which pins should illuminate for each connection type.
Note: When no connection is detected between the connectors of the cable being
tested, the LEDs will not illuminate
Straight (Proper) Connection
When all the LEDs illuminate on both the Master and Remote units, the
cable is properly wired and ready to install/use.
10-415-933796-EN.indd 4
Remote
Continuity
Off
Sweep
Power
Master
4
11/15/2017 9:42:44 A
Detecting Connections
Crossed Connection
If the wires in the cable are out of order or crossed, the LEDs on the Remote
Identifier will illuminate to show in what order they are wired. In the diagram
below, when the Master unit shows pin 14 illuminated, pin 19 on the
Remote unit will illuminate, indicating those connections are crossed.
Note: Crossed connections cannot be tested in “Continuity” mode.
10-415-933796-EN.indd 5
Remote
Continuity
Off
Sweep
Power
Master
5
11/15/2017 9:42:44 A
Detecting Connections
Open Circuit
If the same LEDs on both the Master and Remote units remain off, the
corresponding wire is an open circuit.
10-415-933796-EN.indd 6
Remote
Continuity
Off
Sweep
Power
Master
6
11/15/2017 9:42:45 A
Detecting Connections
Short Circuit
If a short circuit is detected, the Remote unit’s LEDs will not illuminate, but
the Master units LEDs will illuminate brighter.
10-415-933796-EN.indd 7
Remote
Continuity
Off
Sweep
Power
Master
7
11/15/2017 9:42:45 A
Warranty and Product Registration
1-YEAR LIMITED WARRANTY
TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of one (1) year from the date of initial
purchase. TRIPP LITE’s obligation under this warranty is limited to repairing or replacing (at its sole option) any such defective products. To
obtain service under this warranty, you must obtain a Returned Material Authorization (RMA) number from TRIPP LITE or an authorized
TRIPP LITE service center. Products must be returned to TRIPP LITE or an authorized TRIPP LITE service center with transportation charges
prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase. This warranty
does not apply to equipment, which has been damaged by accident, negligence or misapplication or has been altered or modified in any way.
EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to
the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, TRIPP LITE
is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of
substitutes, claims by third parties, or otherwise.
Product Registration
Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win
a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
FCC Notice, Class B
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to this equipment not expressly approved by Tripp Lite could void the user’s authority to operate this equipment.
WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)
Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when customers buy new
electrical and electronic equipment from Tripp Lite they are entitled to:
• Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on the country)
• Send the new equipment back for recycling when this ultimately becomes waste
Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life
support equipment or to significantly affect its safety or effectiveness is not recommended.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
10-415-933796-EN.indd 8
8
17-10-415 93-3796_RevA
11/15/2017 9:42:45 A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising