CyberPower | CP2RAIL02 | User manual | CyberPower CP2RAIL02 User Manual

CyberPower CP2RAIL02 User Manual
BPE72V60ART2US, BPE36V60ART2US, BP144VL2U01,
BP144VL2U01, OL6KSTF, OL10KSTF
OL 3U series
OL6KRT, OL8KRT, OL10KRT, OL6KRTHW, OL8KRTHW,
OL10KRTHW, OL6KRTMB, OL8KRTMB, OL10KRTMB, OL6KRTF,
OL8KRTF, OL10KRTF, OL6000ERT3UD, OL8000ERT3UD,
OL10000ERT3UD, OL6000ERT3UP, OL8000ERT3UP,
OL10000ERT3UP, OL6KERT3UPM, OL8KERT3UPM,
OL10KERT3UPM, BP240VL3U01, BP240VL3U02,
BPE240V30ART3US, BPE240V50ART3US, BPE240V30ART3U,
BPE240V50ART3U
RAIL KIT - CP2RAIL02
Note: CP2RAIL02 is also applicable to above models suffixed with “N”.
1. Select the proper holes on the rack for positioning the UPS and
rackmount rails.
2. Position the guide screws on the rails into the rear rack square
holes to temporarily support the rails in place and adjust the rail
depth to match your rack depth.
3. Screw the front rail to the rack with M5X6L pan head screws and
plastic washers, and the same for the rear rail.
INSTALLATION INSTRUCTION
INTRODUCTION & SAFETY INSTRUCTIONS
UNPACKING
UPS RACKMOUNT INSTALLATION
This guide teaches you how to mount your PR 2U and OL 2U/3U
UPS series and Extended Battery Module (EBM) into a rack
enclosure horizontally with CP2RAIL02 rail kit. This guide is for
common rack and rack enclosure. It might not be applicable to all
mounting applications. Please contact the manufacturer of your
rack and rack enclosure if the hardware is not suitable for mounting.
ATTENTION! During the installation, DO NOT turn on the unit. It
may cause electric shocks. Please ensure the UPS/EBM is OFF and
unplugged from an AC outlet before installation.
ATTENTION! The UPS/EBM is heavy. Be careful when lifting the unit.
ATTENTION! The mounting rails are heavy. Be careful when fixing
the rails to the rack and rack enclosure.
ATTENTION! There shall be at least 2 people to install the PR 2U
and OL 2U UPS/EBM series, and at least 3 people to install the OL
3U UPS/EBM series.
APPLIED PRODUCTS
PR 2U Series
PR750RT2U, PR1000RT2U, PR1500RT2U, PR2000RT2U,
PR2200RT2U, PR3000RT2U, PR750RTXL2U, PR1000RTXL2U,
PR1500RTXL2U, PR2000RTXL2U, PR2200RTXL2U,
PR3000RTXL2U, PR2200RTXL2UA, PR3000RTXL2UA,
PR2200RTXL2UHVA, PR3000RTXL2UHVA, PR750ERT2U,
PR1000ERT2U, PR1500ERT2U, PR2000ERT2U, PR2200ERT2U,
PR3000ERT2U, PR750ERTXL2U, PR1000ERTXL2U,
PR1500ERTXL2U, PR2000ERTXL2U, PR2200ERTXL2U,
PR3000ERTXL2U, PR2200ERTXL2UA, PR3000ERTXL2UA,
BP48VP2U01, BP48VP2U02, BP48VP2U03, BP48VP2U04
OL 2U Series
OL1000RTXL2U, OL1500RTXL2U, OL2200RTXL2U,
OL3000RTXL2U, OL1000ERTXL2U, OL1500ERTXL2U,
OL2000ERTXL2U, OL3000ERTXL2U, OL5KRTHD, OL6KRTHD,
OL5KERTHD, OL6KERTHD, BP36V60ART2U, BP72V60ART2U,
Copyright © 2019 Cyber Power Systems, Inc. All rights reserved.
PR 2U Series
Left & Right Rackmount
Rails x 1 EACH
Left & Right Hanging
Brackets x 1 EACH
(14) M5X6L Pan Head Screw
(2) Rackmount Bracket
(8) M5X7L
Flat Head Screw
(8) Plastic Washer
(2) Rackmount Handle
(4) M4X8L
Flat Head Screw
(4) M5X12L
Pan Head Screw
RAIL INSTALLATION
4U
9
Rackmount Rail
8
9
3U
7
7
8
6
2U
5
4
4
4
4
3
3
2
3U
7
7
6
5
4U
Rackmount Rail
1U
1
UPS 2U Rackmount Bracket
2
2U
1U
1
UPS 3U Rackmount Bracket
1. Prepare the mechanical parts from your UPS mechanical accessory.
2. Attach two rackmount brackets to the UPS using the provided
M5X7L flat head screws and attach two hanging brackets with the
M5X6L pan head screws.
3. Lift the UPS upon the rackmount rails and slide the unit into the
rack. Fix the UPS to the rack with provided M5X12L pan head
screws or suitable screws and cage nuts. If handles are needed,
fix them to the rackmount brackets with M4X8L flat head screws.
OL 2U Series
OL 3U Series
(2) Rackmount Bracket
(8) M5X7L
Flat Head Screw
(2) Rackmount Bracket
(4) M5X12L
Pan Head Screw
1. Prepare the mechanical parts from your UPS mechanical accessory.
2. Remove the dust covers from the screw holes.
3. Attach two rackmount brackets to the UPS using the provided
M5X7L flat head screws and attach two hanging brackets with the
M5X6L pan head screws.
4. Lift the UPS upon the rackmount rails and slide the unit into the
rack. Fix the UPS to the rack with provided M5X12L pan head
screws or suitable screws and cage nuts.
(8) M5X7L
Flat Head Screw
(4) M5X12L
Pan Head Screw
1. Prepare the mechanical parts from your UPS mechanical accessory.
2. Remove the dust covers from the screw holes.
3. Attach two rackmount brackets to the UPS using the provided
M5X7L flat head screws and attach two hanging brackets with the
M5X6L pan head screws.
4. Lift the UPS upon the rackmount rails and slide the unit into the
rack. Fix the UPS to the rack with provided M5X12L pan head
screws or suitable screws and cage nuts.
Cyber Power Systems, Inc.
www.cyberpower.com
For USA and Canada:
4241 12th Ave East, Suite 400
Shakopee, MN 55379
Toll-free: (877) 297-6937
For all other regions:
Please visit our website for local contact information.
K01-0000744-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising