CyberPower CP900AVR User Manual
CP900AVR/CP1200AVR/CP1500AVRT
User’s Manual
1
Power Switch
Used as the master on/off switch for equipment connected to the battery power supplied outlets.
2
MUTE button
The button can be used to mute battery mode alerts and to set up the sensitivity. For more information, please refer to the” Function Setup
Guide” section.
Pressing the button will turn off / on the battery mode alarm, including on battery / low battery warnings.
To turn the alarm off, press the MUTE button. You will hear two short beeps when the alarm is turned off.
K01-0000701-00
PRODUCT REGISTRATION
To turn the alarm back on, press the MUTE button. You will hear a short beep when the alarm is turned on.
LED Indicators
3
The LEDs indicators show the UPS status, including On Line / On Battery / AVR and Overload.
Thank you for purchasing a CyberPower product. Please take a few minutes to register your product at: www.cyberpower.com/registration.
4
Battery and Surge Protected Outlets
The UPS has five battery powered/surge suppression outlets for connected equipment to ensure temporary uninterrupted operation of your
Registration certifies your product's warranty, confirms your ownership in the event of a product loss or theft and entitles you to free technical
equipment during a power failure. (DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum, sump pump or other
large electrical devices into the “Battery and Surge Protected Outlets”. The power demands of these devices may overload and
damage the unit.)
Full-Time Surge Protection Outlets
The UPS has five surge suppression outlets.
Circuit Breaker
Located on the back of the UPS, the circuit breaker serves to provide overload and fault protection.
Wiring Fault Indicator (red)
This LED indicator will illuminate to warn the user that a wiring problem exists, such as bad ground, missing ground or reversed wiring. If
support. Register your product now to receive the benefits of CyberPower ownership.
IMPORTANT SAFETY INSTRUCTIONS
5
(SAVE THESE INSTRUCTIONS)
This Manual Contains Important Instructions that should be followed during Installation and Maintenance of the UPS and batteries.
CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive
contaminants. (Please see specifications for acceptable temperature and humidity range).
6
7
CAUTION! To reduce the risk of electric shock, do not remove the cover except to service the battery. Turn off and unplug the unit before
this is illuminated, disconnect all electrical equipment from the outlet and have an electrician verify the outlet is properly wired. The UPS will
not provide surge protection without being plugged into a grounded and properly wired wall outlet.
Serial/USB Ports to PC
The USB port allows connection and communication between the USB port on the computer and the UPS unit.
Coax/Cable/DSS Surge Protection
The Coax/Cable/DSS protection ports will protect any cable modem, CATV converter, or DSS receiver.
Communication Protection Ports
Communication protection ports, bi-directional, will protect a 10/100/1000 Ethernet connection (RJ45).
servicing the batteries. There are no user serviceable parts inside except for the battery.
CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is disconnected.
8
CAUTION! The UPS must be connected to an AC power outlet with fuse or circuit breaker protection. Do not plug into an outlet that is not
grounded.
9
If you need to de-energize this equipment, turn off and unplug the unit.
CAUTION! To avoid electric shock, turn off the unit and unplug it from the AC power source before servicing the battery.
CAUTION! To reduce the risk of fire, connect only to a circuit provided with 20 amperes maximum branch circuit over current protection in
accordance with the National Electric Code, ANSI/NFPA 70.
DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell products for life support or medical
10
11
Outlets Designed for AC Adapters
The unit has two outlets spaced to allow AC power adapter blocks to be plugged into the UPS without blocking adjacent outlets.
applications. DO NOT use in any circumstance that would affect the operation and safety of life support equipment, medical applications, or
patient care.
DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use with or near an aquarium. Condensation
REPLACING THE BATTERY
from the aquarium can cause the unit to short out.
Replacement of batteries located in an OPERATOR ACCESS AREA.
1.
When replacing batteries, replace with the same number of the following battery: CyberPower / RB1270X2C for the CP900AVR /
CP1200AVR and CyberPower / RB1290X2 for CP1500AVRT.
2.
CAUTION! Risk of Energy Hazard, 24 V, maximum 7 Ampere-hour battery for CP900/1200AVR, maximum 9 Ampere-hour battery for
CP1500AVRT. Before replacing batteries, remove conductive jewelry such as chains, wrist watches, and rings. High energy conducted
through these materials could cause severe burns.
DO NOT USE THE UPS ON ANY TRANSPORTATION! To reduce the risk of fire or electric shock, do not use the unit on any transportation
such as airplanes or ships. The effect of shock or vibration caused during transit and the damp environment can cause the unit to short out.
INSTALLING YOUR UPS SYSTEM
INTRODUCTION
Thank you for selecting a CyberPower Systems UPS product. This UPS is designed to provide unsurpassed power protection, operation and
performance during the lifetime of the product.
UNPACKING
Inspect the UPS upon receipt. The box should contain the following:
(a) UPS (b) User’s manual (c) USB A+B type cable
*PowerPanel® Personal software is available on our website. Please visit www.cyberpower.com and go to the Software Section for free
download.
3.
4.
5.
CAUTION! Do not dispose of batteries in a fire. The batteries may explode.
CAUTION! Do not open or mutilate batteries. Released material is harmful to the skin and eyes. It may be toxic.
CAUTION: A battery can present a risk of electrical shock and high short circuit current. The following precautions should be observed
when working on batteries:
1) Remove watches rings, or other metal objects.
2) Use tools with insulated handles.
CAUTION - RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING
TO LOCAL REGULATIONS.
BATTERY REPLACEMENT PROCEDURE:
1.
Turn off and unplug all connected equipment.
2.
Turn the UPS off and unplug it from the AC power source.
3.
Turn the UPS on its side.
4.
Remove two retaining screws located on the bottom of the UPS.
5.
Slide the battery compartment cover completely off of the unit.
6.
Remove the battery which is located on the right side from the compartment.
OVERVIEW
The CP900AVR/CP1200AVR/CP1500AVRT provides complete power protection from utility power that
is not always consistent. The CP900AVR/CP1200AVR/CP1500AVRT features 1500 Joules of surge
protection. The unit provides long lasting battery backup during power outages with maintenance free
batteries. The CP900AVR/CP1200AVR/CP1500AVRT ensures consistent power to your computer
system and includes software that will automatically save your open files and shutdown your computer
7.
8.
9.
10.
system during a utility power loss.
AUTOMATIC VOLTAGE REGULATOR
Disconnect the battery wires from the right side of the battery.
Slide the remaining battery from left to right and remove it from the compartment.
Disconnect the battery wires from the remaining battery.
Install the "left side" replacement battery by connecting the yellow wire (+) to the red connector from the battery and the black wire (-) to
the black connector from the battery. Place the battery into the left side of the compartment.
Install the "right side" replacement battery by connecting the red wire (+) to the red connector from the battery and yellow wire (-) to the
black connector from the battery. Place the battery into the right side of the compartment. Note: Only new batteries should be used for
The CP900AVR/CP1200AVR/CP1500AVRT stabilizes inconsistent utility power voltage to nominal
levels that are safe for equipment. Inconsistent incoming utility power may be damaging to important
11.
data files and hardware, but with Automatic Voltage Regulation (AVR), damaging voltage levels are corrected to safe levels. AVR automatically
replacement and both batteries should be replaced at the same time to insure maximum life span.
Slide back the battery compartment cover and tighten the retaining screws.
Recharge the UPS for 8-16 hours to fully charge the battery.
increases low utility power or decreases high utility power to a consistent and safe 110/120 volts.
HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT
12.
13.
1. Ensure that the equipment plugged into the outlet does not exceed the UPS’s rated capacity (900VA/560W for CP900AVR, 1200VA/720W for
CP1200AVR and 1500VA/900W for CP1500AVRT). If the rated capacity of the unit is exceeded, an overload condition may occur and cause
1
2
3
4
5
the UPS to shut down or the circuit breaker to trip.
2. There are many factors that can affect the amount of power that your computer system will require. It is suggested that the load placed on the
battery outlets not exceed 80% of the unit’s capacity.
HARDWARE INSTALLATION GUIDE
1. Your new UPS may be used immediately upon receipt. However, after receiving a new UPS, to ensure the
battery’s maximum charge capacity, it is recommended that you charge the battery for at least 8 hours. Your
UPS is equipped with an auto-charge feature. When the UPS is plugged into an AC outlet, the battery will
6
7
8
(+)Red
(-)Black
(-)Black
(+)Red
automatically charge whether the UPS is turned on or off.
2. Note: This UPS is designed with a safety feature to keep the system from being turned on during shipment.
The first time you turn the UPS on, you will need to have it connected to AC power or it will not power up.
3. With the UPS unit turned off and unplugged, connect your computer, monitor, and any other peripherals requiring battery backup into the
battery power supplied outlets. DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum, sump pump or other large
Yellow Wire to (+)Red Connector
Red Wire to (+)Red Connector
electrical devices into the “Battery and Surge Protected Outlets”. The power demands of these devices may overload and damage
Black Wire to (-)Black Connector
Yellow Wire to (-)Black Connector
the UPS.
4. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet).
Make sure the wall branch outlet
REMINDER: Batteries are considered HAZARDOUS WASTE and must be disposed of properly.
collect used batteries for recycling, as required by local regulations.
is protected by a fuse or circuit breaker and does not service equipment with large electrical demands
(e.g. air conditioner, copier, etc…). The warranty prohibits the use of extension cords, outlet strips, and
Most retailers that sell lead-acid batteries
surge strips.
5. Press the power switch to turn the unit on.
DEFINITIONS FOR ILLUMINATED LED INDICATORS
The Power On indicator light will illuminate and the unit will
“beep”. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS off and
unplug at least one piece of equipment from the battery power supplied outlets. Make sure the circuit breaker is depressed and then turn the
UPS on.
CONDITION
6. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.
7. To store the UPS for an extended period, cover it and store with the battery fully charged. While in storage, recharge the battery every three
On Line
On Battery
AVR
Overload
Alarm
On
Off
Off
Off
Off
Off
Off
months to ensure battery life.
8. Ensure the wall outlet and UPS are located near the equipment being attached for proper accessibility.
Flashes
Off
BASIC OPERATION
9
DESCRIPTION
Off
USB
2
The UPS is providing power to battery protected
beeping
seconds
outlets from its battery.
Flashes
Rapid Beeping
while
Off
Off
beeping
every 1/2
second
Utility Failure - The UPS is providing battery
power. Rapid beeping indicates the unit will run
out of power shortly.
Overload Fault - Occurs when connected
equipment exceeds the listed capacity of the
7
W IRINGFAULT
Utility Failure-
every 30
SERIAL
OUT
10
Beep twice
8
IN
1
while
Normal
On/Off
Off/On
Off
On
Constant tone
UPS. Turn the UPS off, unplug at least one piece
of equipment from battery outlets, wait 10
seconds, reset the circuit breaker and turn the
3
11
11
unit on.
Short Fault-
6
Unplug at least one piece of equipment from
On/Off
4
Off/On
Off
Off
Constant tone
5
battery outlets and turn the UPS on again.
UPS Fault –
Contact CyberPower Systems for support.
On/Off
Off/On
Off
Off
Beep every 2
seconds
Charger Fault - Contact CyberPower Systems
for support.
FUNCTION SETUP GUIDE – SENSITIVITY SETUP
Limited Warranty and Connected Equipment Guarantee
In line mode, the AC input voltage may not be stable all the time, to prevent the connected equipment from damage caused by the
unexpected voltage fluctuations, please adjust the sensitivity of the unit by the steps as follows:
Read the following terms and conditions carefully before using the CyberPower CP900AVR/CP1200AVR/CP1500AVRT (the “Product”). By using
1. Please make sure that the UPS is in LINE MODE.
the Product you consent to be bound by and become a party to the terms and conditions of this Limited Warranty and Connected Equipment
Guarantee (together referred to as this “Warranty”). If you do not agree to the terms and conditions of this Warranty, you should return the
2. To Enter the Sensitivity Setup mode, press the MUTE Button for 6 seconds until all indicators flash rapidly.
Product for a full refund prior to using it.
3. The unit will show the current sensitivity setting, as shown in the following table.
4. To select Low Sensitivity setting: shortly press MUTE button until one red indicator flashes.
Who is Providing this Warranty?
5. To select Medium Sensitivity setting, shortly press the MUTE button until red and yellow indicators flash.
Cyber Power Systems (USA), Inc. (“CyberPower”) provides this Limited Warranty.
What Does This Warranty Cover?
6. To select High Sensitivity setting, shortly press the MUTE button until green, yellow and red indicators flash.
7. To set up a level of sensitivity, hold down the MUTE button until the green indicator (the first one) illuminates.
8. Once in setup mode, if there is no action within 7 seconds, the unit will exit setup mode without changing any settings.
Indicators
Illuminate
This warranty covers defects in materials and workmanship in the Product under normal use and conditions.
connected to the Product and damaged because of the failure of the Product.
It also covers equipment that was
What is the Period of Coverage?
This warranty covers the Product for three years and connected equipment for as long as you own the Product.
Sensitivity
Description
1
(Red)
Low
If the connected equipment can tolerate more power events (example: unstable power
often associated with stormy weather), select Low Sensitivity and the UPS will go to
Battery Mode less often.
2
(Yellow, Red)
Medium
(Default)
3
(Green, Yellow, Red)
High
Who Is Covered?
This warranty only covers the original purchaser.
The UPS will go to Battery Mode if the power is unstable.
TROUBLESHOOTING
Problem
Circuit breaker button is
projecting from the back of the
unit.
The UPS does not perform
expected runtime.
The UPS will not turn on.
PowerPanel® Personal software
is inactive (all icons are gray).
Possible Cause
Recharge the battery by leaving the UPS plugged in.
Battery is worn out.
Please contact CyberPower Systems about replacement
batteries.
Turn the UPS off. Wait 10 seconds and then turn the UPS
on.
The unit must be connected to a 120V 60Hz outlet.
Before contacting CyberPower, identify Your Product model number, the Purchase Date, and each item of Connected Equipment (E.G.
Computer tower, Computer Monitor, Ink Jet Printer, Cable Modem, etc).
Visit our web site at http://www.cpsww.com/support or Call us at (877) 297-6937.
If your product requires warranty service you must provide a copy of your dated purchase receipt or invoice.
How Do You Open A Connected Equipment Claim?
1.
Call us at (877) 297-6937 or write to us at Cyber Power Systems (USA), Inc., 4241 12th Ave. E., STE 400, Shakopee, MN 55379, or send
3.
Turn the UPS off and unplug at least one piece of
equipment. Wait 10 seconds, reset the circuit breaker by
depressing the button, and then turn the UPS on.
Battery not fully charged.
The on/off switch is designed to
prevent damage from rapidly turning
it off and on.
The unit is not connected to an AC
outlet.
1.
2.
Solution
Circuit breaker has tripped due to an
overload.
How Do You Get Warranty Service?
2.
3.
If the connected equipment is more sensitive to power events, select High Sensitivity
and the UPS will go to Battery Mode more often.
Coverage ends if you sell or otherwise transfer the Product.
4.
us an e-mail message at claims@cpsww.com for instructions, within 10 days of the occurrence.
When you contact CyberPower, identify the Product, the Purchase Date, and the item(s) of Connected Equipment. Have information on all
applicable insurance or other resources of recovery/payment that are available to the Initial Customer and Request a Claim Number.
You must provide a dated purchase receipt (or other proof of the original purchase) for the CyberPower unit and connected equipment.
You also need to provide a description of the damage to your connected equipment.
Pack and ship the product to CyberPower and, if requested, the item(s) of Connected Equipment, a repair cost estimate for the damage to
the Connected Equipment, and all claim forms that CyberPower provides to you. Show the Claim Number on the shipping label or include
it with the product. You must prepay all shipping costs, you are responsible for packaging and shipment, and you must pay the
cost of the repair estimate.
How Long Do I Have To Make A Claim?
All claims must be made within ten days of the occurrence.
What Will We Do To Correct Problems?
CyberPower will inspect and examine the Product.
If the Product is defective in material or workmanship, CyberPower will repair or replace it at CyberPower's expense, or, if CyberPower is unable
The battery is worn out.
Please contact CyberPower Systems about replacement
batteries.
Mechanical problem.
Please contact CyberPower Systems.
The USB / serial cable is not
connected.
Connect the USB / serial cable to the UPS unit and an open
USB / serial port on the back of the computer. You must
use the cable that came with the unit.
The USB / serial cable is connected
to the wrong port.
Check the back of the computer for an additional USB /
serial port. Move the cable to this port.
to or decides not to repair or replace the Product (if defective) within a reasonable time, CyberPower will refund to you the full purchase price you
paid for the Product (purchase receipt showing price paid is required).
If it appears that our Product failed to protect any equipment plugged into it, we will also send you forms for making your claim for the connected
equipment. We will repair or replace the equipment that was damaged because of the failure of our Product or pay you the fair market value
(NOT REPLACEMENT COST) of the equipment at of the time of the damage. We will use Orion Blue Book, or another a third-party valuation
guide, or eBay, craigslist, or other source to establish that amount. Our maximum liability is limited to $300,000 for CP900AVR, $375,000 for
CP1200AVR and $500,000 for CP1500AVR
The unit is not providing battery
power.
Shutdown your computer and turn the UPS off. Wait 10
seconds and turn the UPS back on. This should reset the
unit.
Who Pays For Shipping?
We pay when we send items to you; you pay when you send items to us.
Additional troubleshooting information can be found under “Support” at www.cyberpower.com
What isn’t covered by the warranty?
1.
This Warranty does not cover any software that was damaged or needs to be replaced due to the failure of the Product or any data that is
lost as a result of the failure or the restoration of data or records, or the reinstallation of software.
2.
This Warranty does not cover or apply to: misuse, modification, operation or storage outside environmental limits of the Product or the
equipment connected to it, nor for damage while in transit or in storage, nor if there has been improper operation or maintenance, or use
TECHNICAL SPECIFICATIONS
Model
CP900AVRa
CP1200AVRa
CP1500AVRTa
Capacity
900VA / 560W
1200VA / 720W
1500VA / 900W
with items not designed or intended for use with the Product, such as laser printers, appliances, aquariums, medical or life support devices,
etc.
What are the Limitations?
The sole and exclusive remedies of the Initial Customer are those provided by this Warranty.
1.
This Warranty does not apply unless the Product and the equipment that was connected to it were connected to properly wired and
grounded outlets (including compliance with electrical and safety codes of the most current electrical code), without the use of any
Nominal Input Voltage
120V
Input Frequency
60 Hz ± 3 Hz
On-Battery Output Voltage
120Vac ± 5%
Max. Load for UPS Outlets
(5 Outlets)
Max. Load for Full-Time Surge
Protection outlets (10 Outlets)
900VA / 560W
1200VA / 720W
1500VA / 900W
12 Amp
12 Amp
12.5 Amp
On-Battery Output Wave Form
Simulated Sine Wave
Operating Temperature
+ 32°F to 104° F / 0° C to 40° C
Operating Relative Humidity
0 to 95% non-condensing
Size (W x H x D)
3.9" x 9.8" x 13.7" (99 x 249 x 348 mm)
2.
3.
4.
Net Weight
21.83lbs / 9.9kg
21.83lbs / 9.9kg
24.1lbs / 10.91kg
Battery Type
CyberPower / RB1270X2C
CyberPower / RB1270X2C
CyberPower / RB1290X2
Typical Battery Recharge Time
8 hours to 90% capacity from total discharge
Typical Battery Life
3 to 6 years, depending on number of discharge/recharge cycles
Recommended Battery
Sealed Maintenance Free Lead Acid Battery
Safety Approvals
UL1778(UPS), cUL107., FCC/DoC Class B
The Product was designed to eliminate disrupting and damaging effects of momentary (less than 1ms) voltage spikes or impulses from lightning
or other power transients. If it can be shown that a voltage spike lasting longer than 1ms has occurred, the occurrence will be deemed outside
the rated capabilities of the Product and the Limited Warranty is void. CyberPower Does Not Cover or Undertake Any Liability in Any Event for
Any of the Following:
1.
Loss of or damage to data, records, or software or the restoration of data or records, or the reinstallation of software.
2.
SYSTEM FUNCTIONAL BLOCK DIAGRAM
3.
Advanced Energy-Saving Patented Bypass Technology
Damage from causes other than AC Power Line Transients, spikes, or surges on properly installed, grounded and code-compliant 120 volt
power lines in the United States and Canada; transients, surges or spikes on standard telephone land lines, PBX telephone equipment
lines or Base 10T Ethernet lines, when properly installed and connected. (This exclusion applies, for example, to fluctuations in data
transmission or reception, by CATV or RF transmission or fluctuations, or by transients in such transmission.)
Damage from any circumstance described as excluded above with respect to the Product.
4.
Damages from fire, flood, wind, rain, rising water, leakage or breakage of plumbing, abuse, misuse or alteration of either the product or the
Connected Equipment.
5.
CyberPower excludes any liability for personal injury under the Limited Warranty and Connected Equipment Guarantee. CyberPower
excludes any liability for direct, indirect, special, incidental or consequential damages, whether for damage to or loss of property [EXCEPT
6.
CYBERPOWER GREENPOWER UPS™ TECHNOLOGY
adapters or other connectors.
The Product must have been plugged directly into the power source and the equipment connected to the Product must be directly
connected to the Product and not “daisy-chained” together in serial fashion with any extension cords, another Product or device similar to
the Product, surge suppressor, or power tap. Any such installation voids the Limited Warranty.
The Product and equipment connected to it must have been used properly in a suitable and proper environment and in conformance with
any license, instruction manual, or warnings provided with the Product and the equipment connected to it.
The Product must have been used at all times within the limitations on the Product’s VA capacity.
FOR (AND ONLY FOR) the specific limited agreement of CyberPower to provide certain warranty benefits regarding "Connected
Equipment" under this Warranty], loss of profits, business interruption, or loss of information or data. NOTE: Some States or Provinces do
not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you.
The Product is not for use in high-risk activities or with aquariums. The Product is not designed or intended for use in hazardous
environments requiring fail-safe performance, or for use in any circumstance in which the failure of the Product could lead directly to death,
personal injury, or severe physical or property damage, or that would affect operation or safety of any medical or life support device
(collectively, "High Risk Activities"). CyberPower expressly disclaims any express or implied warranty of fitness for High Risk Activities or
with aquariums. CyberPower does not authorize use of any Product in any High Risk Activities or with Aquariums. ANY SUCH USE IS
IMPROPER AND IS A MISUSE OF THE PRODUCT.
CyberPower’s patented GreenPower UPS™ with Bypass Technology reduces UPS energy costs by up to 75% compared
to conventional UPS models. Even when utility power is normal, conventional UPS models constantly pass power through
a transformer. By contrast, under normal conditions the advanced circuitry of a GreenPower UPS™ bypasses the
transformer. As a result, the power efficiency is significantly increased while decreasing waste heat, using less energy,
and reducing energy costs.
Where Can I Get More Information?
The application of the United Nations Convention of Contracts for the International Sale of Goods is expressly excluded.
When an abnormal power condition occurs, the GreenPower UPS™ automatically runs power through its transformer to
regulate voltage and provide “safe” power. Since utility power is normal over 88% of the time, the GreenPower UPS™
55379; call us at (877) 297-6937; or send us an e-mail message at claims@cyberpowersystems.com.
operates primarily in its efficient bypass mode.The GreenPower UPS™ is also manufactured in accordance with the
Restriction on Hazardous Substances (RoHS) directive making it one of the most environmentally-friendly on the market today.
FCC Compliance Statement
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help"
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
Canadian Compliance Statement
CAN ICES-3 (B)/NMB-3(B)
CyberPower is the warrantor under this Limited Warranty.
For further information please feel free to contact CyberPower at Cyber Power Systems (USA), Inc. 4241 12th Ave E., STE 400, Shakopee, MN
Cyber Power Systems (USA), Inc. encourages environmentally sound methods for disposal and recycling of its UPS products.
Please dispose and/or recycle your UPS and batteries in accordance to the local regulations of your state.
All rights reserved. Reproduction without permission is prohibited.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising