CyberPower HT1006U User Manual
CONGRATULATIONS ON YOUR PURCHASE
CAUTION
Thank you for selecting the CyberPower HT1006U Surge
Protector. The information contained in this brochure
explains the features and operation of the HT1006U. Please
take a few moments to read this manual.
TO REDUCE THE RISK OF ELECTRIC SHOCK - Use only
in dry locations and only indoors. DO NOT plug into
another relocatable power tap. DO NOT “daisy chain”
surge protectors. DO NOT use with any aquarium
equipment. DO NOT use if properly grounded outlets are
not available. DO NOT install this device if there is not at
least 10 meters (30 feet) or more of wire between the
electrical outlet and electrical service panel. This device
features an internal protection that will disconnect the
surge protective component at the end of its useful life,
but will maintain power to the load – now unprotected.
FEATURES
10-Outlet Surge Protector
HT1006U
1
2
3
1. ON/OFF Reset Control Switch and Circuit Breaker
Controls power to all outlets. The switch is also a 15A
breaker. When an overload occurs, it will automatically
switch off. To resume operation, ensure the overload
condition is removed and reset the surge protector by
switching the unit ON.
2. Ground Indicator LED
Illuminated when the Ground protection feature is
working properly.
3. Surge Protected Indicator
Illuminated when the surge protection feature is working
properly.
4. Six Standard Outlets and Four Transformers
Safety Covers
Slide the plastic outlet cover over outlets that are not
used. This ensures the safety of children and prevents
potential electric shocks and damage caused by a highly
dusty environments.
5. USB Charging Ports*
Connect and charge up to two (2) USB devices using the
surge protected USB charging ports.
*USB outlets cannot be used as a USB hub. This device
does not transfer data.
SPECIFICATIONS
4
5
•
•
•
•
•
•
•
•
•
•
•
•
•
Model Number: HT1006U
Outlets: 6 Standard Outlets and 4 Transformers
Power Cord length: 6 ft
Surge Protection: 3,600 Joules
Electrical Rating: 125V/15A/1875W
UL Clamping Voltage: UL 1449 3rd/500V (H-N, H-G, N-G)
Maximum Peak Current: 135,000A
3 AC Lines Protected: H-N: 75,000A, H-G: 30,000A, N-G:
30,000A; (The maximum surge possible on household
Wiring is 6,000 volts)
Response Time: Less than 1 nanosecond
Attenuation: Up to 32dB
EMI/RFI Filtration: 150 kHz to 100 MHz
USB Charger Rating: 5V/2.4A total
Circuit Breaker: Resettable 15 Amp
TROUBLESHOOTING
If the Grounded indicator does not light when you plug in
the surge protector, move the surge protector to a
different grounded three-prong AC outlet. If it still does
not light, return the product to dealer for assistance. If
the surge protector proves to be working properly, your
outlets may not be a properly grounded and need to be
repaired by a professional electrician. If the Grounded
indicator turns off after a period of use, the surge
protection has been depleted. Replace your surge
protector.
If the Protected indicator does not light, the surge
protector’s AC lines is no longer protected from surge.
Replace the surge protector. The surge protector may
have received a power surge or spike beyond its
specified limits that overloaded the protection circuitry
and rendered it inactive. The surge protector has
protected your connected equipment, but it will not
protect against future surges and spikes.
TECHNICAL SUPPORT
Please contact our Tech Support department with
installation, troubleshooting, or general product
questions.
• Phone: 1-877-297-6937
• Email: tech@cpsww.com
• Hours of Operation: Monday – Friday, 7:00am – 6:00pm
CST
USER’S MANUAL
1
Copyright © 2017 Cyber Power Systems, Inc. All rights reserved.
2
LIMITED WARRANTY AND CONNECTED
EQUIPMENT GUARANTEE
Read the following terms and conditions carefully before
using the CyberPower HT1006U (the “CPS Product”). By
using the CPS Product, you consent to be bound by the
terms and conditions of this Limited Warranty and
Connected Equipment Guarantee (together referred to as
this “Warranty”). IF YOU DO NOT AGREE TO THE TERMS
AND CONDITIONS OF THIS WARRANTY, YOU SHOULD
RETURN THE PRODUCT FOR A FULL REFUND PRIOR TO
USING IT.
Who is providing this Warranty, what does it cover?
Cyber Power Systems (USA), Inc. (“CyberPower”)
provides this Limited Warranty. It only covers the original
purchaser and ends if you no longer own the CPS Product.
This warranty covers defects in materials and
workmanship in the CPS Product under normal use and
conditions. It also covers equipment connected to the CPS
Product and damaged because of the failure of the CPS
Product. This warranty covers the CPS Product and
connected equipment for as long as you own the CPS
Product.
What must I do to make a warranty claim?
1. Call us at (877) 297-6937 or write to us at Cyber Power
Systems (USA), Inc., 4241 12th Ave. E., STE 400,
Shakopee, MN 55379, or send us an e-mail message at
claims@cpsww.com for instructions, within 10 days of
the occurrence.
2. When you contact CyberPower, identify the Product,
the Purchase Date, and the item(s) of Connected
Equipment. Have information on all applicable insurance
or other resources of recovery/payment that are
available to the Initial Customer and Request a Claim
Number.
3. You must provide a dated purchase receipt (or other
proof of the original purchase) for the CyberPower unit
and connected equipment. You also need to provide a
description of the damage to your connected
equipment.
4. Pack and ship the product to CyberPower and, if
requested, the item(s) of Connected Equipment, a
repair cost estimate for the damage to the Connected
Equipment, and all claim forms that CyberPower
provides to you. Show the Claim Number on the
shipping label or include it with the product. You must
prepay all shipping costs, you are responsible for
packaging and shipment, and you must pay the cost of
the repair estimate.
What will CyberPower do to correct problems?
CyberPower will inspect and examine the CPS Product. If
the CPS Product is defective in material or workmanship,
CyberPower will repair or replace it at CyberPower’s
expense, or CyberPower will refund the full purchase price
you paid for the CPS Product (purchase receipt
3
showing price paid is required). If the CPS Product failed
to protect any equipment plugged into it, we will also
send you forms for making your claim for the connected
equipment. We will repair or replace the equipment that
was damaged because of the failure of the CPS Product
or pay you the fair market value (NOT REPLACEMENT
COST) of the equipment at of the time of the damage.
We will use Orion Blue Book, another a third-party
valuation guide, eBay, craigslist, or other source to
establish that amount. Our maximum liability is limited to
$350,000 for the HT1006U.
Who pays for shipping?
We pay when we send items to you; you pay when you
send items to us.
What are some things this Warranty does not cover?
1. THIS WARRANTY DOES NOT COVER ANY
SOFTWARE THAT WAS DAMAGED OR NEEDS TO BE
REPLACED DUE TO THE FAILURE OF THE CPS
PRODUCT OR ANY DATA THAT IS LOST AS A RESULT
OF THE FAILURE OR THE RESTORATION OF DATA OR
RECORDS, OR THE REINSTALLATION OF SOFTWARE.
2. This Warranty does not cover: misuse, modification,
operation or storage outside environmental limits of
the CPS Product or the equipment connected to it, or
for damage while in transit or in storage, nor if there
has been improper operation or maintenance, or use
with items not designed or intended for use with the
CPS Product, such as laser printers, appliances,
aquariums, medical or life support devices, etc.
What are the other limitations?
The sole and exclusive remedies of the Initial Customer
are those provided by this Warranty.
1. This Warranty does not apply unless the CPS Product
and the connected equipment were connected to
properly wired and grounded outlets (including
compliance with electrical and safety codes of the
most current electrical code), without the use of any
adapters or other connectors.
2. The CPS Product must have been plugged directly into
the power source and the equipment connected to the
CPS Product must be directly connected in the CPS
Product, not “daisy-chained” together in serial fashion
with any extension cords, another Product or device
similar to the CPS Product, surge suppressor, or power
tap. Any such installation voids the Warranty.
3. The CPS Product and connected equipment must have
been used properly in a suitable and proper
environment, in conformance with any applicable
license, instruction manual, or warnings.
4. The CPS Product must have been used at all times
within the limitations on the CPS Product’s VA
capacity.
4
Where can I get more information?
Contact CyberPower at 4241 12th Ave E., STE 400,
Shakopee, MN 55379; call us at (877) 297-6937; or send us
an e-mail message at claims@cpsww.com.
PRODUCT REGISTRATION
Prompt product registration assures coverage under the
Limited Warranty, and also allows the opportunity to be
notified of product enhancements, upgrades, and other
announcements.
Registration is quick and easy. Go to Product Registration
page at www.cyberpower.com.
CONTACT INFORMATION
Cyber Power Systems, Inc. 4241 12th Avenue East Suite
400 Shakopee, MN 55379
Toll-free: 1-877-297-6937 | CyberPower.com
CONFORMANCE APPROVALS
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, And
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not
expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment. This Class B digital apparatus complies with
Canadian ICES-003.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Please join CyberPower in caring for the
environment by recycling this manual.
This device is manufactured using environmentally-safe
procedures in compliance with the Restriction of
Hazardous Substances (RoHS) directive.
Cyber Power Systems, Inc.
www.cyberpower.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising