CyberPower | PR1000ELCDRT2U | User manual | CyberPower PR1000ELCDRT2U User Manual

CyberPower PR1000ELCDRT2U User Manual
EN
User’s Manual
Professional Rack Mount LCD Series
PR1000ELCDRT2U/PR1500ELCDRT2U/
PR2200ELCDRT2U
K01-0000431-01
IMPORTANT
INSTRUCTIONS
IMPORTANTSAFETY
SAFETY INSTRUCTIONS
This manual contains important instructions. Please read and follow all instructions carefully during installation
and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or operate the
UPS.
CAUTION! The UPS must be connected to a grounded AC power outlet with fuse or circuit breaker protection.
DO NOT plug the UPS into an outlet that is not grounded. If you need to power-drain this equipment, turn off
and unplug the unit.
CAUTION! The battery can power hazardous components inside the unit, even when the AC input power is
disconnected.
CAUTION! The UPS should be near the connected equipment and easily accessible.
CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor
area, free of conductive contaminants. (Please see specifications for acceptable temperature and humidity
range).
CAUTION! To reduce the risk of an electric shock, do not remove the cover, except to service the battery.
There are no user serviceable parts inside, except for the battery.
CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before servicing
the battery or installing a computer component.
CAUTION! To reduce the risk of fire, connect the UPS to a circuit with 16 amperes maximum over-current
protection in accordance to CE requirement.
CAUTION! The AC outlet where the UPS is connected should be close to the unit and easily accessible.
CAUTION! Please use only VDE-tested, CE-marked mains cable, (e.g. the mains cable of your equipment),
to connect the UPS to the AC outlet.
CAUTION! Please use only VDE-tested, CE-marked power cables to connect any equipment to the UPS.
CAUTION! When installing the equipment, ensure that the sum of the leakage current of the UPS and the
connected equipment does not exceed 3.5mA.
CAUTION! This is permanently connected equipment and only qualified maintenance personnel may carry
out installations.
CAUTION! Do not unplug the unit from AC Power during operation, as this will invalidate the protective
ground insulation.
CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! Under no circumstances this
unit should be used for medical applications involving life support equipment and/or patient care.
CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire, do not use with or near
aquariums. Condensation from the aquarium can come in contact with metal electrical contacts and cause
the machine to short out.
CAUTION! DO NOT USE WITH LASER PRINTERS! The power demands of laser printers are too large for a
UPS.
DO NOT INSTALL THE UPS WHERE IT WOULD BE EXPOSED TO DIRECT SUNLIGHT OR NEAR A
STRONG HEAT SOURCE!
DO NOT BLOCK OFF VENTILATION OPENINGS AROUND THE HOUSING!
DO NOT CONNECT DOMESTIC APPLIANCES SUCH AS HAIR DRYERS TO UPS OUTPUT SOCKETS.
1
Copyright © 2016 CyberPower Systems, Inc.
INSTALLING
YOURYOUR
UPS SYSTEM
(continued)
INSTALLING
UPS SYSTEM
UNPACKING
The box should contain the following:
®
(1) UPS unit x 1; (2) User manual x 1; (3) Phone line x 1; (4) PowerPanel Business Edition software CD x 1; (5)
USB A+B type cable x 1; (6) Rack mount Brackets x 2; (7) Emergency Power Off Cable (gray) x 1; (8) Serial
Interface Cable (DB-9) x 1; (9) Power cord x 4 (Power cord x 6 for PR2200ELCDRT2U)
AUTOMATIC VOLTAGE REGULATOR(AVR)
The PR1000ELCDRT2U/PR1500ELCDRT2U/PR2200ELCDRT2U can stabiliz
the consistent utility power. The utility power may be damaging to important data
and hardware, but Automatic Voltage Regulation helps the computer not
experience dangerous voltage levels. Automatic Voltage Regulator automatically
regulates low or high voltages to keep equipment working at safe AC power levels
(220/230/240V) without switching to battery. Your equipment can operate normally
even meet the power problems, such as, shout brownouts and blackouts. The
unit’s powerful sealed lead-acid batteries will provide power only if the incoming
voltage drops below 150V or increases above 300V.
INSTALLING YOUR UPS SYSTEM (continued)
SYSTEM BLOCK DIAGRAM
HARDWARE INSTALLATION GUIDE
1. Battery charge loss may occur during shipping and storage. The first time the UPS is used, it is strongly
recommended to charge the batteries for at least 12 hours to ensure that the batteries are at theirmaximum
charge capacity. To recharge the batteries, simply plug UPSinto an AC outlet, the batteries will charge
whether the UPS is powered on or not.
2. With the UPS off and unplugged, connect your computer, monitor, and any externally powered data
storage device (Hard drive, Tape drive, etc.) into the outlets. DO NOT plug a laser printer, copier, space
heater, vacuum, paper shredder or other large electrical device into the UPS. The power demands
of these devices will overload and possibly damage the unit.
3. To protect a fax, telephone, modem line or network cable, connect the telephone or network cable from the
wall jack outlet to the jack marked “IN” on the UPS. Then, connect a telephone cable or network cable from
the jack marked “OUT” on the UPS to the modem, computer, telephone, fax machine, or network device.
4. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is
protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g.
air conditioner, copier, etc). The warranty prohibits the use of extension cords, outlet strips, and surge
strips.
2
Copyright © 2016 CyberPower Systems, Inc.
5. Press the power switch to turn the UPS on. The Power-On indicator light will illuminate. If an overload is
detected, an audible alarm will sound and the UPS will emit one long beep. In order to reset it, turn the unit
off and unplug some equipment from outlets. Make sure the total load of the equipment connected to the
UPS is within the unit’s safe range, (refer to the technical specifications), and then turn the unit on.
6. To maintain an optimal battery charge, leave the UPS plugged into an AC outlet at all times.
7. Before storing the UPS for an extended period of time, turn the unit OFF. Then cover it and store it with the
batteries fully charged. Recharge the batteries every three months or so, to ensure good battery capacity
and long battery life; further, this might also prevent damage to the unit from an unlikely battery leakage.
8. The unit provides one Primary Serial Port (I), one Secondary Serial Port (II), and one USB port to allow
connection and communication between the unit and any attached computers. The Primary Serial Port (I)
as well as its paired USB port allow for bi-directional communication among the UPS and the primary
®
connected computer running the PowerPanel Business Edition Software. The computer can monitor the
UPS and alter its various programmable parameters. When there is a power failure, the computer
connected to the port will start to shut down after a user controlled delay based on the settings given to
thePowerPanel® Business Edition Software. The Secondary Serial Port II, only allows the UPS to initiate
the connected computer’s graceful auto-shutdown in case of an emergency.
Note: If the USB port is used, the serial port(s) will be disabled. They cannot be used simultaneously.
Note: PowerPanel® Business Edition Software is available on our website. Please visit
www.cyberpowersystems.com and go to Products/Software section for free download.
9. EPO (Emergency Power Off) Port: Follow the appropriate circuit diagram below to wire the cable to your
EPO configuration. The EPO remote switch is a switch installed in an outside area, connected to the unit
via an ordinary RJ-11 phone line. In case of an emergency, it can be used to immediately cut-off power
from the UPS unit
Option 1: User Supplied Normally Open Switch (Recommended)
Option 2: User Supplied Normally Closed Switch
3
Copyright © 2016 CyberPower Systems, Inc.
BASIC OPERATION
FRONT / REAR PANEL DESCRIPTION
1. Power Switch
Master on/off switch for equipment connected to the UPS.
2. Power On Indicator
Indicate that the AC utility input power’s condition is normal and that the UPS outlets are providing power, free
of surges and spikes.
3. Multifunction LCD Readout
An LCD that shows various UPS information using icons and messages.
4. LCD Readout Toggle Button
Used to select among a variety of information the LCD can display.
5. Battery Backup, Surge Protected and AVR protected Outlets
This unit provides a total of six outlets with battery backup and surge protection. They ensure that connected
equipment will keep an uninterrupted operation over a period of time, during a power failure.
Critical /Non-critical
It is possible to program the unit in a way so that the outle block marked as “non-Critical”, (6 ports), will stop the
provision of power to connected equipment after a certain period of time, thus making more runtime available
for the equipment connected on the outlets marked as “Critical”, (2 ports). In other words, the user can
establish runtime priority for certain connected equipment, maximizing its “availability” during a prolonged
®
power outage. This type of control takes place with the use of the provided PowerPanel Business Edition S/W.
6. AC Inlet
Connect the AC Power cord to a properly wired and grounded outlet.
7. Output Circuit Breaker
The circuit breaker serves to provide output overload and fault protection.
8. Input Circuit Breaker
The circuit breaker serves to provide input overload and fault protection.
4
Copyright © 2016 CyberPower Systems, Inc.
BASIC OPERATION (continued)
9. USB port to PC
This is a connectivity port allowing communication and control among the UPS and the connected computer.
®
You should install on your computer the PowerPanel Business Edition software appropriate to the operating
system you are using.
10. Surge Protected Communication Ports - RJ11/RJ45
These ports are being used to protect from various surge-conditions the standard RJ-45/RJ-11 based, (ADSL,
LAN, Phone/Modem-Lines), cabling systems.
11. Serial Port I (Primary)
Serial port I allow for bi-directional communication among the UPS and the computer. The UPS can control the
computer’s shutdown in case of an emergency, and at the same time, the computer can monitor the UPS and
alter its various programmable parameters.
12. Serial Port II (Secondary)
Serial Port II allows the UPS to initiate the connected computer’s graceful auto-shutdown in case of an
emergency.
13. SNMP/HTTP Network slot
Remove the cover panel to install optional SNMP, allowing your UPS be controlled and monitored via a network
connection.
14. EPO (Emergency Power Off) Port
Allow for an emergency UPS Power-Off from a remote location.
BATTERY REPLACEMENT
Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the batteries:
Servicing the batteries should only be performed by professionals. Please Contact your dealer, or email to:
support@cpsww.eu. Make a note for the replacement battery pack number, (RBP832), regarding
PR1000ELCDRT2U and PR1500ELCDRT2U models; (RBP842), regarding PR2200ELCDRT2U model.
CAUTION! Use only the specified type of battery: BP7.2-12FR(BB) for PR1000ELCDRT2U/
PR1500ELCDRT2U, HR9-12FR(BB) for PR2200ELCDRT2U. Contact your dealer for replacement batteries.
CAUTION! The battery may present the risk of electrical shock. Do not dispose of batteries on fire, since they
may explode. Follow all local ordinances regarding the proper disposal of batteries.
CAUTION! Do not open or mutilate the batteries. Released electrolyte is harmful to the skin and eyes and
may be toxic.
CAUTION!
A battery can present a high risk of short-circuits and electrical shocks.
Take the following precautions before replacing the battery:
1.
2.
3.
4.
5.
Remove all watches, rings or other metal objects from your hands.
Only use tools with insulated handles.
DO NOT lay tools or other metal parts on top of battery or any battery terminals.
Wear rubber gloves and shoes.
Determine if the battery is grounded. If so, remove source of ground. CAUTION: CONTACT WITH A
GROUNDED BATTERY CAN RESULT IN ELECTRICAL SHOCK! The likelihood of such a shock will be
greatly reduced if such grounding is removed during installation and maintenance.
5
Copyright © 2016 CyberPower Systems, Inc.
BATTERY REPLACEMEN (continued)
BATTERY REPLACMENT PROCEDURE:
1. Remove the front panel
on the right side.
2. Remove the two retaining screws
of the cable protection cover then
remove the cover.
3. Remove the two retaining
screws of the cable connectors.
4. Disconnect the black wire and red
wire from the battery.
5. Remove the three retaining
screws.
6. Put the new battery packs back into the
compartment. Tighten up the screws and
replace the cable protection cover and the
front panel. Recharge the unit for 12
hours to ensure the UPS performs
expected runtime.
REMINDER! The used batteries are hazardous wastes and must be disposed through recycling. Most retailers
that sell lead-acid batteries collect used batteries for recycling, as required by the local regulations.
6
Copyright © 2016 CyberPower Systems, Inc.
DEFINITION FOR ILLUMINATED LCD INDICATORS
1.
Input voltage meter: This meter measures the
AC voltage from the wall outlet. The INPUT
voltage readout is used to identify the input
voltage information. This can be used as a
diagnostic tool to identify poor-quality input
power. Units are listed in V (Volts). When the
UPS connect to any equipment, the AVR can
provide a stable
220/230/240V power output.
In the event of a complete loss of power, severe
brownout, or over voltage, the UPS relies on its
internal battery to back up to supply a consistent
220/230/240V output.
2.
Output voltage meter: The Output Voltage
screen measures, in real time, the AC voltage
that the UPS is providing to your connected
equipment via the UPS outlets. Units are listed
in V (Volts).
3.
Estimate run time: The Estimated Runtime
Screen displays how many minutes of runtime
can be expected of the UPS if it were to
experience a power outage. When runtime
becomes shorted, the battery capacity will
decrease; (battery capacity bar indicator will be
falling.) Note: The number displayed may be less
than actual runtimes for low loads.
The LCD displays detailed information on the UPS status and
current power conditions to alert you to potential power
problems before the affect your equipment. Note! All related
UPS information is based on that you should turn on the UPS.
4.
Normal icon: This icon illuminates when the UPS is working under normal conditions.
5.
Battery icon: When there is a severe brownout or blackout, this icon will appear followed by an alarm,
(two short beeps), indicating that the UPS is now working using its internal batteries. Once the batteries
are run out of power, (over a period of time), a constant alarm will sound. If this happens and main power
has not been restored, it is recommended that you save your files and turn off your equipment manually
as soon as possible.
6.
Automatic Voltage Regulation (AVR) icon: This icon will appear when the unit is automatically
regulating low or high AC input line voltage conditions, without resulting to the use of battery power.
7.
Silent mode icon: This icon appearing indicates that the buzzer will not be beeping while in battery
operating mode. During Silent mode, the unit’s alarm does not sound until the Battery Capacity falls to <
20%.
8.
Over load icon: This icon will appear followed by an alarm, indicating that an overload condition has
been reached. To recover from the overload condition, start unplugging your equipment from the UPS
outlets until the icon disappears and the alarm stops.
9.
Fault icon: When activated indicates a system fault error. Please refer to the troubleshooting table for
possible causes and solutions.
10.
BATT. CAPACITY: BATT. CAPACITY is shown as a bar chart; each segment indicates approximately a
20% of battery capacity.
11.
LOAD CAPACITY: Load CAPACITY is shown as a bar chart; each segment indicates approximately a
20% of load capacity.
7
Copyright © 2016 CyberPower Systems, Inc.
LCD SETUP FUCTIONS
1. General Mode:
a. Press the “Display-Toggle” button to check the status of the UPS status:
1
2
3
4
5
6
7
8
9
Item
Input Voltage
Output Voltage
Output Frequency
Load
Estimate Run Time
Load Capacity
Battery Capacity
Centigrade
Fahrenheit
Unit
V
V
Hz
Kw
Min
%
%
℃
℉
b. Press and hold the “Display-Toggle” button for 4 seconds,
If the machine is in the Battery Mode with active alarm, it will become silent.
If the machine is in the Line Mode, a self- diagnostic test will take place.
c. If the “Display-Toggle” button remains untouched for over 30 seconds, the LCD backlight will turn off
automatically.
2. Set-up Mode
Step 1: Hold the “Display-Toggle” button for 10 seconds to enter the UPS Set-Up Mode.
Step 2: By pressing the Display toggle, users can switch between setup functions. Some User Configurable
functions are as follows:
a. Sensitivity: Set the level of tolerance for UPS. Increase the UPS compatibility for local utility power
condition.
High: The UPS will turn to battery power more often to provide the steady power supply to the
connected equipment.
Low: The UPS will tolerate more fluctuations and turn to battery power less often.
b. Voltage Mode: The AC output voltage on battery mode. There are 3 different settings (220,230,240).
c. Battery Lifetime: Show the batteries already used time. Reset the logger when battery module
replacement or first time installation. Note: CLr is the command on LCD to reset Battery Lifetime.
These programmable items are sorted by unit as in the following table:
Items
Sensitivity
Voltage Mode (220/230/240)
Battery Lifetime
Firmware Version
Unit
None
V
Y
None
Step 3: Press and hold the display-toggle for 4 seconds. When the icons blink, the value of each item is
changed by slightly pressing the toggle.
Step 4: To save the value and return to general mode, press and hold the toggle for 4 seconds.
Note! If the UPS is left idle for over 30 seconds during setup, it will turn off the backlight and return to
general mode automatically.
Note! If the user does not want to save the new settings and return to the general mode, there are two
methods:
(1) Wait for the backlight to turn off, or,
(2) By pressing and holding the “Display-toggle” key for 10 second.
8
Copyright © 2016 CyberPower Systems, Inc.
CYBERPOWER GREENPOWER UPS™ TECHNOLOGY
GreenPower UPS™
CyberPower's GreenPower UPS™ Circuit Design is a solution to this problem "Power Loss."
When the Utility Power is operating normally, Green Power UPS™ works in Bypass Mode.
Our GreenPower UPS™ design conducts power only through the Relay and still provides
normal output voltage. Bypassing the transformer reduces power consumption thereby
conserving energy and saving money. When the utility power is abnormal the UPS will
operate under Battery or AVR Mode. Under this condition Green Power UPS™ and a
traditional UPS would operate about the same.
On average utility power operates 88% of the time and the CyberPower GreenPower Technology will work in its
money/ energy saving Bypass Mode.
9
Copyright © 2016 CyberPower Systems, Inc.
TECHNICAL SPECIFICATIONS
Model
PR1000ELCDRT2U
PR1500ELCDRT2U
PR2200ELCDRT2U
Capacity (VA)
1000
1500
2200
Capacity (Watts)
900
1350
1980
Input
Input connections
IEC 320 C14
IEC 320 C20
Nominal Input Voltage
220 / 230 / 240Vac
Input Voltage Range
150Vac – 300Vac
Input Frequency Range
50/60Hz +/- 3Hz (Auto Sensing)
Output
On Battery Output Voltage
220 / 230 / 240Vac +/- 5%
On Battery Output
50/60Hz +/- 0.1Hz
Frequency
Transfer Time (Typical)
4ms
Overload Protection
On Utility: Circuit Breaker, On Battery: Internal Current Limiting
Surge Protection and Filtering
Lightning / Surge
Yes
Protection
Internet Ready (DSL /
Phone / FAX / Modem
RJ11/RJ45 (One In/One Out)
Protection)
Physical
Output Receptacles
(8) IEC 320 C13
Dimensions(cm)
2U Rack, 43.3 x 8.8 x 38.8
Weight (kg)
25.5
27
30
Battery
Sealed Maintenance-Free
12V / 7.0AH x4
12V / 9.0AH x4
Lead Acid Battery
Hot Swappable Batteries
Yes
Warning Diagnostics
Indicators
Power On, LCD Display (Using Battery, AVR, Load Level, Battery Level)
Audible Alarms
On Battery, Low Battery, Overload
Environmental
Operating Temperature
32°F to 104°F ( 0°C to 40°C)
Operating Relative
0 to 95% Non-Condensing
Humidity
Communication
®
PowerPanel Business
Windows 10 / 8.1 / 8 / 7 / Vista / XP / 2000, Server 2008 / 2003
Edition Software
Management
Self -Test
Manual Self-Test
Auto-Charger/Auto-Restart
Yes
COM Interface
True RS232 x 1+ Contact Closure x 1
Built- in USB interface
Yes
SNMP/HTTP Networking
Optional
10
Copyright © 2016 CyberPower Systems, Inc.
TROUBLE SHOOTING
Problem
Possible Cause
Circuit breaker has tripped
due to an overload.
Outlet does not
provide power to
equipment
The UPS does not
perform expected
runtime.
The UPS will not turn
on.
®
PowerPanel
Personal
Edition is inactive.
Batteries are discharged
Unit has been damaged by
a surge or spike.
Uncritical outlets have
turned off automatically
due to an overload.
Batteries are not fully
charged.
Batteries are degraded
The on/off switch is
designed to prevent
damage by rapidly turning it
off and on.
The unit is not connected to
an AC outlet.
The batteries have
degraded.
Mechanical problem.
The serial cable or USB
cable is not connected.
The cable is connected to
the wrong port.
Solution
Turn the UPS off and unplug at least one piece of
equipment. Wait 10 seconds, reset the circuit breaker
and then turn the UPS on.
Recharge the unit for at least 4 hours
Contact CyberPower Systems about replacement
batteries at www.cpsww.eu.
Push the toggle button to make the uncritical outlets turn
on.
Recharge the batteries by leaving the UPS plugged in.
Contact CyberPower Systems about replacement
batteries at www.cpsww.eu.
Turn the UPS off. Wait 10 seconds and then turn the
UPS on.
The unit must be connected to a 220/230/240v outlet.
Contact CyberPower Systems about replacement
batteries at www.cpsww.eu.
Contact CyberPower Systems at www.cpsww.eu.
Connect the cable to the UPS unit. You must use the
cable that came with the unit.
Try another port of your computer.
The unit is not providing
power of batteries.
Shutdown your computer and turn the UPS off. Wait 10
seconds and turn the UPS back on. This should reset the
unit.
The serial cable is not the
cable that was provided
with the unit.
You must use the cable included with the unit for the
Software.
For more information, contact us at:
For more information, visit eu.cyberpowersystems.com or contact.
CyberPower Systems
Flight Forum 3545 5657DW Eindhoven The Netherlands
Tel: +31 40 2348170, E-MAIL: sales@cyberpower-eu.com
CyberPower Systems Inc. (USA)
4241 12th Avenue East, Suite 400, Shakopee, MN 55379, U.S.A.
Tel: +1 952 4039500, Fax: +1 952 4030009, E-MAIL: sales@cyberpowersystems.com
Entire contents copyright ©2016 CyberPower Systems, Inc. All rights reserved. Reproduction in whole or in
®
®
part without permission is prohibited. PowerPanel and PowerPanel Plus are trademarks of CyberPower
Systems (USA) Inc.
11
Copyright © 2016 CyberPower Systems, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising