CyberPower OL10KRT3UHW User Manual
User’s Manual
OL6000RT3UPDU
OL8000RT3UPDU
OL10000RT3UPDU
OL6KRT3UHW
OL8KRT3UHW
OL10KRT3UHW
CyberPower Systems (USA), Inc.
4241 12th Avenue East Suite 400 Shakopee, MN 55379
Phone: 877-297-6937
Fax: 952-403-0009
www.CPSww.com
K01-0000211-00
IMPORTANT SAFETY INSTRUCTIONS
This manual contains important instructions. Please read and follow all instructions carefully during installation and operation of the unit. Read this manual
thoroughly before attempting to unpack, install, or operate the UPS.
CAUTION! The UPS must be connected to a grounded AC power
outlet with fuse or circuit breaker protection. DO NOT plug the UPS into
an outlet that is not grounded. If you need to power-drain this equipment,
turn off and unplug the unit.
CAUTION! Wiring must be done by qualified personnel.
CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT
EQUIPMENT! Under no circumstances this unit should be used for
medical applications involving life support equipment and/or patient care.
CAUTION! The battery can power hazardous components inside the
unit, even when the AC input power is disconnected.
CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce
the risk of fire, do not use with or near aquariums. Condensation from
the aquarium can come in contact with metal electrical contacts and
cause the machine to short out.
CAUTION! The UPS should be placed near the connected equipment
and easily accessible.
CAUTION! To prevent the risk of fire or electric shock, install in a
temperature and humidity controlled indoor area, free of conductive
contaminants. (Please see specifications for acceptable temperature and
humidity range).
CAUTION! Do not dispose of batteries in fire as the battery may
explode.
CAUTION! Do not open or mutilate the battery, released electrolyte is
harmful to the skin and eyes.
CAUTION! (No User Serviceable Parts): Risk of electric shock, do
not remove cover. No user serviceable parts inside. Refer servicing to
qualified service personnel.
CAUTION! A battery can present a risk of electric shock and high short
circuit current. The following precaution should be observed when
working on batteries
1. Remove watches, rings or other metal objects.
2. Use tools with insulated handles.
CAUTION! (Non-Isolated Battery Supply): Risk of electric shock,
battery circuit is not isolated from AC power source; hazardous voltage
may exist between battery terminals and ground. Test before touching.
CAUTION! The unit has a dangerous amount of voltage. When the
UPS indicators is on, the units may continue to supply power thus the
unit’s outlets may have a dangerous amount of voltage even when it’s not
plugged in to the wall outlet.
CAUTION! To reduce the risk of fire, connect the UPS to a branch
circuit with 40 amperes (OL6000, OL6K) / 50 amperes (OL8000, OL8K) /
60 amperes (OL10000, OL10K) maximum over-current protection in
accordance with the National Electric Code, ANSI/NFPA 70.
CAUTION! Make sure everything is turned off and disconnected
completely before conducting any maintenance, repairs or shipment.
CAUTION! The AC outlet where the UPS is connected should be close
to the unit and easily accessible.
CAUTION! Connect the Protection Earth (PE) safety conductor before
any other cables are connected.
CAUTION! Please use only UL-marked mains cable, (e.g. the mains
cable of your equipment), to connect the UPS to the AC outlet.
WARNING! (Fuses): To reduce the risk of fire, replace only with the
same type and rating of fuse.
CAUTION! Please use only UL-marked power cables to connect any
equipment to the UPS.
CAUTION! When installing the equipment, ensure that the sum of the
leakage current of the UPS and the connected equipment does not
exceed 3.5mA.
DO NOT INSTALL THE UPS WHERE IT WOULD BE EXPOSED TO
DIRECT SUNLIGHT OR NEAR A STRONG HEAT SOURCE!
CAUTION! The OL6000/OL8000/OL10000/OL6K/OL8K/OL10K models
are permanently-connected equipment and only qualified maintenance
personnel may carry out installations.
DO NOT BLOCK OFF VENTILATION OPENINGS AROUND THE
HOUSING!
CAUTION! Do not unplug the unit from AC Power during operation, as
this will invalidate the protective ground insulation.
DO NOT CONNECT DOMESTIC APPLIANCES SUCH AS HAIR
DRYERS TO UPS OUTPUT SOCKETS!
CAUTION! To avoid electric shock, turn off and unplug the unit before
installing the input/output power cord with a ground wire. Connect the
ground wire prior to connecting the line wires!
SERVICING OF BATTERIES SHOULD BE PERFORMED OR
SUPERVISED BY PERSONNEL KNOWLEDGE OF BATTERIES AND
THE REQUIRED PRECAUTIONS. KEEP UNAUTHORIZED
PERSONNEL AWAY FROM BATTERIES!
CAUTION! Do not use an improper size power cord as it may cause
damage to your equipment and cause fire hazards.
1
Copyright © 2011 CyberPower Systems, Inc.
UNPACKING
Power module
Battery module
Rackmount ears (Stands) (2) * 2 sets
PDU or HW PDU with Manual Bypass
Tie plate (1) * 1 set
User’s manual
Register card
Flat head screws: M5X8L (8) * 2 sets
Pan head screws: M5X12L (12) * 2 sets
Rackmount left rail * 2 sets
Rackmount right rail * 2 sets
Plastic washers (8) * 2 sets
Phone line
Screw hole dust covers (10) * 2 sets
USB communication cable
Power cord
Serial Interface Cable (RS-232)
PowerPanel® Business Edition software CD
2
Copyright © 2011 CyberPower Systems, Inc.
HARDWARE INSTALLATION
HARDWARE INSTALLATION
Step 4: Adjust rackmount rails to fit your rack
These versatile UPS systems can be mounted in a rackmount or vertical
tower orientation. This versatility is especially important to growing
organizations with changing needs that value having the option to
position a UPS on a floor or in a rackmount system. Please follow the
instructions below for the respective mounting methods.
Attach the rackmount rail to your rack with two M5X12L screws and two
plastic washers at the front of the rack. (Located in position 1 & position 6)
Do not tighten the screws. Adjust the rail size on the rail assembly of your
rack. Secure the rail to the rear of the rack with two M5X12L screws and
two plastic washers. Tighten all screws at the front and rear of the rail.
Once completed, perform the same steps for assembling the other
rackmount rail.
SAFETY PRECAUTIONS
CAUTION! To prevent the risk of fire or electric shock, only use the
supplied hardware to attach the mounting brackets.
RACKMOUNT INSTALLATION
Step 1: Remove the internal battery trays from the Battery module
(See page 19)
Step 2: Rackmount ears installation
Attach the two rackmount ears to the Battery module using the provided
screws M5X8L*8pcs.
Place the Battery module on a flat stable surface with the front of the unit
facing toward you. Secure the Battery module to your rack with four
M5X12L screws at the front of the rack. (Located in position 2 & position
8)
Step 3: Rackmount rail Installation
The rails adjust to mount in 48-cm (19-inch) panel racks from 52 to
91.5cm (20.5 to 36 inches) deep. Select the proper holes in the rack for
positioning the Battery module in the rack. The Power module or the
Battery module takes up position 1 through position 9.
Step 5: Place the internal battery trays back into the Battery module
(See page 19)
Once completed, perform the same steps for the Power module.
CAUTION! The Battery module must be installed below the Power
module.
3
Copyright © 2011 CyberPower Systems, Inc.
HARDWARE INSTALLATION
VERTICAL/TOWER INSTALLATION
Step 1: Rotate the Multifunction LCD Module
Step 2: Attach the base stands
Unscrew the right panel of the Power module. Separate the right panel
from the UPS. Gently lift the LCD module out. Rotate it to the tower
orientation. Reinstall it for a tower configuration.
Secure the tie bracket with the screws (M5X8*4pcs). Tighten the screws
(M5X12*4pcs) of the base stands (rackmount ears) onto the bottom of
the power module and the battery module.
Step 3: Attach dust covers
Insert dust covers into the rackmount ear screw holes that are not being
used.
ELECTRICAL INSTALLATION
After completing the hardware installation of the UPS, you are now ready
to plug in the UPS and connect your equipment.
4
Copyright © 2011 CyberPower Systems, Inc.
HARDWARE INSTALLATION
PDU or HW PDU INSTALLATION
Step 1: Remove the cover from the PDU’s
Step 3: Screw the PDU’s
Loosen the two screws and remove the cover from the PDU’s to expose
the connectors.
Secure the PDU’s to the Power module with four screws.
Step 2: Attach the PDU’s to the Power module
Align the connectors of the PDU’s with the connectors of the Power
module to attach the device and tighten the two screws to fix the cover on
the PDU or HW PDU.
ELECTRICAL INSTALLATION
After completing the hardware installation of the UPS, you are now ready
to plug in the UPS and connect your equipment.
SAFETY PRECAUTIONS
CAUTION! Installation environment should be in a temperature and
humidity controlled indoor area free of conductive contaminants. Do not
install this UPS where excessive moisture or heat is present (Please see
specifications for acceptable temperature and humidity range).
CAUTION! Never install a UPS, or associated wiring or equipment,
during a lightning storm.
CAUTION! Do not work alone under hazardous conditions.
CAUTION! In case of the risk of electric shock, do not remove the top
cover.
CAUTION! The battery can energize hazardous live parts inside even
when the AC input power is disconnected.
5
Copyright © 2011 CyberPower Systems, Inc.
INSTALLING YOUR UPS SYSTEM
SYSTEM BLOCK DIAGRAM
Maintenance
Bypass
Internal
Bypass
Input
Input
Filter
PFC
AC/DC
Charger
AC/DC
Battery
Inverter
DC/AC
BUS
STS
Control
&
Monitoring
Output
Filter
Bypass
Switch
Output
LCD Module
USB & DB9
SNMP Slot
Line Mode
Battery Mode
Bypass Mode
Maintenance Bypass
HARDWARE INSTALLATION GUIDE
1. Battery charge loss may occur during shipping and storage. Before
6. This UPS is equipped with an auto-charge feature. When the UPS is
using the UPS, it’s strongly recommended to charge batteries for four
hours to ensure the batteries’ maximum charge capacity. To recharge the
batteries, simply plug the UPS into an AC outlet.
plugged into an AC outlet, the battery will automatically charge, even
when the unit is switched off.
2. When using the included software, connect either the serial or the
AC outlet at all times.
7. To maintain an optimal battery charge, leave the UPS plugged into an
USB cable between the computer and the corresponding port on the UPS.
Note: If the USB port is used, the serial port will be disabled. They cannot
be used simultaneously. After connecting to either the USB port or the
Serial port on the UPS, a computer with the PowerPanel® Business
Edition Agent software installed can control the operating schedule,
battery test, outlets, as well as obtain UPS status information. However,
other computers with PowerPanel® Business Edition Client software can
only obtain UPS status information via LAN connection.
8. Before storing the UPS for an extended period of time, turn the unit
OFF. Then cover it and store it with the batteries fully charged. Recharge
the batteries every three months to ensure good battery capacity and
long battery life. Maintaining a good battery charge will help prevent
possible damage to the unit from battery leakage.
9. The UPS has one USB port (default) and one Serial port that allows
storage device (Hard drive, Tape drive, etc.) into the outlets only when
the UPS is off and unplugged. DO NOT plug a laser printer, copier, space
heater, vacuum, paper shredder or other large electrical device into the
UPS. The power demands of these devices will overload and possibly
damage the unit.
connection and communication between the UPS and any attached
computer running the PowerPanel® Business Edition Agent software. The
UPS can control the computer’s shutdown during a power outage
through the connection while the computer can monitor the UPS and alter
various programmable parameters. Note: Only one communication port
can be used at a time. The port not in use will automatically become
disabled or the serial port will be disabled if both ports are attached.
4. To protect a fax machine, telephone, modem line or network cable,
10. EPO (Emergency Power Off) Port:
connect the telephone or network cable from the wall jack outlet to the
jack marked “IN” on the UPS and connect a telephone cable or network
cable from the jack marked “OUT” on the UPS to the modem, computer,
telephone, fax machine, or network device.
EPO ports allow administrators the capability to connect the UPS unit to
customer-supplied EPO switches. These installations give operators a
single access point to immediately power-off all equipment connected to
the UPS during an emergency.
5. Press the ON/OFF switch to turn the UPS on. The Power-On indicator
11. To avoid electric shock, turn the unit OFF and disconnect the unit
light will display when activated. If an overload is detected, an audible
alarm will sound and the UPS will continuously emit two beeps per
second. For resetting the unit, unplug some equipment from the outlets.
Make sure your equipment carries a load current within the unit’s safe
range, (refer to the technical specifications).
from utility power before hardwiring the UPS (in/out power cord). The
in/out power cord MUST be grounded.
3. Connect your computer, monitor, and any externally-powered data
6
Copyright © 2011 CyberPower Systems, Inc.
HARDWIRING THE INPUT/ OUTPUT TERMINALS
CHECK CIRCUIT BREAKER/WIRING
Check branch circuit breaker rating and wiring dimensions with the following table.
UPS Capacity
Branch Circuit Breaker
Wiring AWG
Wiring mm
6KVA
40A
10 AWG
5.5 mm
2
8KVA
50A
8 AWG
8.0 mm
2
10KVA
60A
6 AWG
14.0 mm
2
2
INPUT/ OUTPUT CONFIGURATION
Hardwire the input/output terminals as shown in the following diagram.
Wiring
AWG
UPS
Mains
L1 L2 PE
PDU/HW
Input
Circuit Breaker
PFC
AC/DC
L1
L2
Inverter
DC/AC
STS
PE
Output
L1 L2 PE
Battery
Manual
Bypass
External
EPO
L1
L2
PE
SAFETY PRECAUTIONS
CAUTION! Input and Output circuit breakers must be “OFF” during the building installation.
CAUTION! An additional two pole disconnect device is necessary during the building installation.
CAUTION! Disconnected EPO will immediately shut down the logic circuit output of the UPS. Wiring the EPO signal is optional.
CAUTION! Local safety rules may require a separate, external EPO to turn off output circuit breakers. Refer to local wiring rules, the EPO should use
approved components.
Step 1: Remove the inspection window cover
Loosen the four screws to remove the inspection window cover.
Step 2: Remove the terminal block cover
Loosen the four screws to remove the terminal block cover.
7
Copyright © 2011 CyberPower Systems, Inc.
HARDWIRING THE INPUT/ OUTPUT TERMINALS
Step 3: Input configuration
Insert the input cable through the appropriate cable gland (not included)
and connect the three wires to the input terminal block.
Step 5: Fix the terminal block cover on the PDU’s
Tighten the four screws to fix the terminal block cover on the PDU’s.
Step 6: Fix the inspection window cover on the PDU’s
Tighten the four screws to fix the inspection window cover on the PDU’s.
Step 4: Output configuration
Insert the output cable through the appropriate cable gland (not included)
and connect the three wires to the output terminal block.
8
Copyright © 2011 CyberPower Systems, Inc.
BACKFEED PROTECTION
BACKFEED PROTECTION OPERATION
1. If the Bypass circuit is shorted and the UPS is running in Line Mode or Battery Mode, backfeed protection will be active and the external isolation device
(Magnetic Contactor) will open.
2. Save your data and perform a controlled shutdown.
3. Contact CyberPower for repair.
WITHOUT BACKFEED PROTECTION CONFIGURATION
1. Hardwire the input terminals as shown in the following diagram.
2. Do not remove the interconnection wires (Jumper1 / Jumper2) on “Backfeed Protection Connector”.
Mains
UPS
L1 L2 PE
L1
L1
L2
L2
I/P
EMI
L1
IP-L1
L2
IP-L2
PE
PSDR
1
2
Backfeed
3
Jumper1
Jumper2
4
AC-L1
5
AC-L2
WITH BACKFEED PROTECTION CONFIGURATION
1. Customers should provide an external isolation device (Magnetic Contactor) which is upstream and outside the UPS and capable of supporting the UPS
input current.
2. Remove the interconnection wires (Jumper1 / Jumper2) on “Backfeed Protection Connector”.
3. Hardwire the input terminals and “Backfeed Protection Connector” as shown in the following diagram.
4. The external isolation device must be installed in the Mains path.
Mains
L1 L2 PE
UPS
A1
L1
L2
MC
L1
L1
L1
L2
L2
L2
A2
I/P
EMI
L1
IP-L1
L2
IP-L2
PE
PSDR
1
2
2A Fuse
(Slow Blow)
Backfeed
3
4
AC-L1
5
AC-L2
9
Copyright © 2011 CyberPower Systems, Inc.
BASIC OPERATION
POWER MODULE FRONT/REAR PANEL DESCRIPTION
OL6KRT3UPDUPM / OL8KRT3UPDUPM / OL10KRT3UPDUPM
1. Power Button / Power on Indicator
Master ON/OFF for the UPS. Indicates that the UPS is on and supplying
power.
7. Remote Control Port
Connects to remote LCD module to the UPS.
8. Surge Protected Communication Ports RJ-45/RJ-11
These ports are used to protect standard RJ-45/RJ-11 based products
(ADSL, LAN, Phone/ Modem-Lines) and cabling systems from surges.
2. UPS Status / Fault / Replace Battery LED Indicator
Indicates the status of the UPS whether is operating in Line, Battery or
Bypass Mode, or the UPS has an internal fault and the battery need to be
replaced.
9. Relay Output Connector
Convert UPS signals into real potential-free Dry Contacts for industrial
control.
3. Multifunction LCD Readout
Shows UPS status, information, settings and events.
10. SNMP/HTTP Network slot
Slot to install the optional SNMP card for remote network control and
monitoring.
4. Function Buttons
Scroll up, scroll down, select and cancel LCD menu.
5. USB port
This is a connectivity port which allows communication and control
between the UPS and the connected computer. It is recommended to
install the PowerPanel® Business Edition Agent software on the
PC/Server connected with the USB cord.
11. Backfeed Protection Connector
Prevents power feedback from the inverter to utility power in case of
power failure and a fault in the bypass circuit.
12. EPO (Emergency Power Off) Connector
Enables an emergency UPS Power-Off from a remote location.
6. Serial Port
Serial port provides communication between the UPS and the computer.
The UPS can control the computer’s shutdown during a power outage
through the connection while the computer can monitor the UPS and alter
its various programmable parameters.
13. Extended Runtime Battery Module Connector
Connection for additional CyberPower XL Battery modules.
14. Input / Output Connectors
Use these connectors to attach the PDU or HW PDU to the Power
module.
10
Copyright © 2011 CyberPower Systems, Inc.
BASIC OPERATION
PDU / HW PDU FRONT/REAR PANEL DESCRIPTION
OL6K6UPDU
OL8K10K6UPDU
OL6K3UPDUHW
OL8K10K3UPDUHW
1. Input Circuit Breaker
Provides input overload and fault protection.
7. Connectors Cover
Provides safety protection when removing the PDU or HW PDU.
2. Manual Bypass Switch
Provide UPS output to connected equipment when turned to Normal.
Provide utility power to connected equipment when turned to Bypass.
8. Output Circuit Breaker
Provides output overload and fault protection.
9. Battery Backup & Surge Protected Outlets
Provides battery backup and surge protection. They ensure power is
provided to connected equipment over a period of time during a power
failure.
3. Input / Output Terminal Block
Connect to utility power / your equipment.
4. Interlock Bracket
Avoid turning the “Manual Bypass Switch“ under normal operation.
Critical / Noncritical Load
Allows the creation of load priorities to ensure that battery power
reserves are transferred to specified outlets during a power outage. The
unit can be programmed to provide additional runtime for equipment
connected to the “CRITICAL” outlets, while stopping the power supply to
equipment connected to “NONCRITICAL” outlets after a designated
period of time.
5. Inspection Window
Visual check the wiring condition and secure the terminal.
6. Input / Output Connectors
Use these connectors to attach the PDU or HW PDU to the Power
module.
11
Copyright © 2011 CyberPower Systems, Inc.
BASIC OPERATION
BATTERY MODULE FRONT/REAR PANEL DESCRIPTION
1. On-board Replaceable Fuse Cover
Replaceable fuse is accessible from the rear panel. It must
be done by qualified personnel.
2. AC Circuit Breaker
Provides overload and fault protection.
3. AC Output Outlet
Use this outlet to connect to the AC Input Inlet of a
downstream Battery module.
4. AC Input Inlet (Charge Only)
AC power connectivity to wall receptacle.
5. Input Connector
Use this input connector to daisy chain the next Battery
module. Remove the connector cover for access.
6. Output Cable
Use this output cable to connect the Battery module to the
Power module or to the next Battery module.
7. DC Breaker
Use the DC breaker to disconnect battery output.
BP240V30ART3U / BP240V50ART3U
CONNECTION #1 : POWER MODULE WITH ONE BATTERY MODULE
Step 1: Turn off the DC breaker of the Battery module.
Step 2: Loosen the two screws to remove the battery cable
retention bracket of the power module.
Step 3: Use the output cable of the Battery module to connect
the Battery module to the Power module.
Step 4: Rotate the battery cable retention bracket and tighten
the two screws to fix battery cable.
Step 5: Use a power cord to plug AC input inlet of the battery
module into a wall receptacle.
Step 6: Turn on the DC breaker of the Battery module.
12
Copyright © 2011 CyberPower Systems, Inc.
BASIC OPERATION
CONNECTION #2 : POWER MODULE WITH MULTIPLE BATTERY MODULES
Step 1: Connect the 1st Battery module to the Power module
using the instructions above.
Step 2: Turn off the DC breaker of the 2nd Battery module.
Step 3: Loosen the two screws to remove the battery cable
retention bracket of the 1st battery module.
Step 4: Use the output cable of the 2nd Battery module to
connect the 2nd Battery module to the 1st Battery
module.
Step 5: Rotate the battery cable retention bracket and tighten
the two screws to fix battery cable.
Step 6: Use a power cord to plug AC input inlet of the 2nd battery
module into AC output outlet of the 1st Battery module.
Step 7: Turn on the DC breaker of the 2nd Battery module.
13
Copyright © 2011 CyberPower Systems, Inc.
OPERATION INSTRUCTIONS FOR LCD MODULE
LED INDICATORS – UPS STATUS
LED Indicators
Color
UPS Status Description
ON/OFF
White
UPS power is on.
ON-LINE
Green
UPS is operating in Line Mode.
BATTERY ON
Yellow
UPS is operating in Battery Mode.
BYPASS
Yellow
UPS is operating in Bypass Mode, Manual Bypass or ECO (Economy) Mode.
FAULT
Red
UPS has an internal fault. See “Trouble Shooting” for additional information.
REPLACE BATTERY
Red
Battery will soon need to be replaced due to insufficient runtime.
LCD SCREEN – UPS STATUS
LCD Screen
UPS Status Description
Line Mode
UPS is operating in Line Mode.
Battery Mode
UPS is operating in Battery Mode.
Bypass Mode
UPS is operating in Bypass Mode.
Manual Bypass
UPS is operating in Manual Bypass.
ECO Mode
UPS is operating in ECO (Economy) Mode.
BUTTON OPERATION
Button
Operation Description
ON/OFF
Press this button to turn on or turn off UPS.
▲
Press this button to scroll up in the LCD menu.
▼
Press this button to scroll down in the LCD menu.
ENTER
Press this button to select an option.
ESC
Press this button to cancel or return to previous LCD menu.
14
Copyright © 2011 CyberPower Systems, Inc.
LCD SETUP FUNCTIONS
MULTI-FUNCTION LCD MAIN MENU
Press “Enter” button to activate “MAIN MENU”.
MAIN MENU submenu
Function Description
Information
Displays the UPS information.
Configure
Displays the UPS settings that can be configured by the user.
Event Log
Displays the 3 most recent events,
(day/hour/minute), and event description.
by
event
count,
time
LCD INFORMATION READOUT
There are 19 types of UPS information available for display.
1.
Press the “ENTER” button to activate the “MAIN MENU”.
2.
Press the “▲” and “▼” buttons to scroll to the “Information” option.
3.
Press the “ENTER” button to select the “Information” submenu.
4.
Press the “▲” and “▼” buttons to scroll through the “Information” submenu in the following table.
5.
Press the “ESC” button to return to UPS Status.
Information Submenu
Description
O/P Volt
= XXX.XV
Displays the Output Voltage
O/P Freq
= XX.XHz
Displays the Output Frequency
I/P Volt
= XXX.XV
Displays the Input Voltage
I/P Freq
= XX.XHz
Displays the Input Frequency
O/P Load =
XXX%
X.XA
Displays the Output Load Percentage of Maximum load
O/P Amp
=
O/P Watt
=XXXXXW
Displays the Output Wattage
O/P VA
=XXXXXVA
Displays the Output VA
BAT Volt
= XXX.XV
Displays the Battery Voltage
BAT Cap
=
Displays the Estimated Percentage of Battery Capacity
XXX%
Displays the Output Current
BAT Runtime =XXXM
Displays the Estimated Battery Runtime in Minutes
EBM Number =
Displays the External Battery Module Number
X
Displays the Approximate inside Temperature in both ℃ (Celsius) and ℉
TEMP =XX°C / XXX°F
SBM
Rating
=
XXXXX
= XXK VA
MCU Ver =
XXXX
(Fahrenheit) for the UPS
Displays the Stage of Smart Battery Management
Displays the UPS Rating
Displays the MCU Firmware Version
Model Name
Displays the UPS Model Name
Date & Time
- - - - / - - / - - - -:- -
Displays the present Date & Time
Next BAT Change
XXX / XXXX
Displays the next Battery Change Date & Time
15
Copyright © 2011 CyberPower Systems, Inc.
LCD SETUP FUNCTIONS
LCD EVENT LOG
3 Event Logs of UPS can be recorded.
1.
Press the “ENTER” button to activate the “MAIN MENU”.
2.
Press the “▲” and “▼” buttons to scroll to the “Event Log” option.
3.
Press the “ENTER” button to select the “Event Log” submenu.
4.
Press the “▲” and “▼” buttons to scroll through the “Event Log” submenu in the following table.
5.
Press the “ESC” button to return to UPS Status.
Event Log Submenu
Description
XXDXXHXXM (without PowerPanel® Business or RMCARD302)
(X)
--/--
- -:- - (with PowerPanel® Business or RMCARD302)
Event Content
MULTI-LANGUAGE INTERFACE
Users can configure 1 of the 4 available languages for display.
([English], [Españ ol-Spanish], [Français-French], [Deutsch-German])
1.
Press the “ENTER” button to activate the “MAIN MENU”.
2.
Press the “▲” and “▼” buttons to scroll to the “Configure” option.
3.
Press the “ENTER” button to select the “Configure” submenu.
4.
Press the “▲” and “▼” buttons to scroll through the “Language” options.
5.
Press the “ENTER” button to select the “Language” submenu.
6.
Press the “▲” and “▼” buttons to scroll to the language that you want to select.
You may be prompted to save the selection, if so press the “ENTER” button to save the setting.
7.
Press the “ESC” button to cancel or return to previous LCD menu.
LCD SETTINGS CONFIGURATION
There are 24 UPS settings that can be configured by the user.
1.
Press the “ENTER” button to activate the “MAIN MENU”.
2.
Press the “▲” and “▼” buttons to scroll to the “Configure” option.
3.
Press the “ENTER” button to select the “Configure” submenu.
4.
Press the “▲” and “▼” buttons to scroll to the “Configure” submenu in the following table.
5.
Press the “ENTER” button to select the setting you want to configure.
The first configuration parameter will be displayed on the second column of LCD screen.
6.
Press the “▲” and “▼” buttons to scroll through the different parameters.
7.
Press the “ENTER” button to select the parameter you want to change.
You may be prompted to save the selection, if so press the “ENTER” button to save the setting. Some options are saved
and started automatically. (See the following table for additional details.)
8.
Press the “ESC” button to cancel or return to the previous LCD menu.
16
Copyright © 2011 CyberPower Systems, Inc.
LCD SETUP FUNCTIONS
Configure Submenu
Available Settings
Default Setting
Output Voltage
= [200V] [208V] [220V] [230V] [240V]
208V
Range= [+/- 1%] [+/- 2%] [+/- 3%] [+/- 4%] [+/- 5%]
Sync Freq Window
+/- 5%
[+/- 6%] [+/- 7%] [+/- 8%] [+/- 9%] [+/-10%]
Range= [+10%/-10%] [+10%/-15%] [+10%/-20%]
Bypass V Window
Bypass Condition
+10%/-15%
[+15%/-10%] [+15%/-15%] [+15%/-20%]
[Check Freq/Volt] [Check Volt Only] [No Bypass]
Check Freq/Volt
[Disable] [Enable]
Disable
ECO Mode*
[V Range= +/-15%] [V Range= +/-10%]
(for [Enable])
V Range= +/-10%
Manual Bypass
[Disable] [Enable]
Disable
Battery Test
[Activate?]
None
Audible Alarms
[Disable] [Enable]
Enable
EBM Number
= [0] [1] [2] [3] [4] [5] [6] [7] [8] [9] [10]
0
Wiring Fault
[Disable] [Enable]
Disable
NCL Control
[Outlet On] [Outlet Off]
Outlet On
Language
[English] [Español-Spanish] [Français-French] [Deutsch-German]
English
Generator Mode**
[Disable] [Enable]
Disable
Communication
[Disable] [Enable]
Enable
Dry Relay Set
[I/P Power Fail] [Battery Low] [Summary Alarm] [UPS On Bypass] [UPS Fail]
I/P Power Fail
Converter Mode***
[Converter Off] [O/P Freq = 50Hz] [O/P Freq = 60Hz]
Converter OFF
Screen Saver
[Disable] [1 Minutes] [5 Minutes]
5 minutes
Clear Event Log
[Activate?]
None
Button OFF LOCK
[Disable] [Enable]
Disable
Charger Function
[SBM] [Constant]
SBM
Signal Inputs
[Disable] [EPO][ROO]
Disable
Charger Check
[Disable] [Enable]
Disable
With Transformer
[Disable] [Enable]
Disable
Backfeed Check
[Disable] [Enable]
Disable
*) This function can’t be set when Manual Bypass, Generator Mode or Converter Mode is enabled.
**) UPS has no bypass when Generator Mode is enabled.
***) UPS has no bypass when Converter Mode is enabled. This function can only be set before the UPS is on.
SILENCING AUDIBLE ALARMS
1.
Press any of four function buttons on the LCD module; Note: the alarm can not be turned off for a “Battery Low”
condition. This condition will still result in an audible alarm.
2.
Configure “Audible Alarms” as “Disable” on the LCD module and it will stop warning of any malfunction audibly.
MANUAL BATTERY TEST
Configure “Battery Test” as “Active” on the LCD module; and it will perform the “Manual Battery Test”
17
Copyright © 2011 CyberPower Systems, Inc.
LCD MODULE REMOTE CONTROL and WALL-MOUNTING INSTRUCTIONS
REMOTE CONTROL
WALL-MOUNTING INSTRUCTIONS
Step 1: Remove the Multifunction LCD Module
Step 1: Remove the Multifunction LCD Module
Unscrew the right panel of the Power module. Separate the right panel
from the UPS. Gently lift the LCD module out. Reinstall the right panel.
Unscrew the right panel of the Power module. Separate the right panel
from the UPS. Gently lift the LCD module out. Reinstall the right panel.
Step 2: Connect the DB26 Cable
Step 2: Rotate the DB26 Connector of LCD Module
Connect the DB26 cable from LCD module to the “Remote Control
Port” on the front panel or rear panel as shown in the following figure.
Step 3: Connect the DB26 Cable
Connect the DB26 cable from LCD module to the “Remote Control
Port” on the front panel or rear panel as shown in the following figure.
Step 4: Mount LCD Module on the Wall
SAFETY PRECAUTIONS
CAUTION! It must be done by qualified personnel.
CAUTION! To avoid electric shock, turn off and unplug the unit before installing REMOTE CONTROL or WALL-MOUNTING INSTRUCTIONS.
18
Copyright © 2011 CyberPower Systems, Inc.
MAINTENANCE
CAUTION! Do not open or mutilate the batteries. Electrolyte fluid is
harmful to the skin/eyes and may be toxic.
CAUTION! To avoid electric shock, turn off and unplug the UPS from
the wall receptacle before servicing the battery.
CAUTION! Only use tools with insulated handles. Do not lay tools or
metal parts on top of the UPS or battery terminals.
Storage
To store your UPS for an extended period, cover it and store with the
battery fully charged. Recharge the battery every three months to ensure
battery life.
Battery Replacement
Please read and follow the Safety Instructions before servicing the
battery. Battery replacement should be performed by trained personnel
who are familiar with the procedures and safety precautions. Make a note
of the replacement Battery module number.
Replacement Batteries
Please refer to the front side of the Battery module for the model number
of the correct replacement batteries. For battery procurement, log onto
www.CPSww.com, or contact your local dealer.
Safety Precautions
Battery Disposal
CAUTION! Only use replacement batteries which are certified by
CyberPower Systems. Use of incorrect battery type is an electrical
hazard that could lead to explosion, fire, electric shock, or short circuit.
CAUTION! Batteries contain an electrical charge that can cause
severe burns. Before servicing batteries, please remove any conductive
materials such as jewelry, chains, wrist watches, and rings.
Batteries are considered hazardous waste and must be disposed of
properly. Contact your local government for more information about
proper disposal and recycling of batteries. Do not dispose of batteries
in fire.
Battery Installation
Step 1: Remove the front panels
Step 2: Remove the retaining screws from
the cable protection cover and then remove
the cover itself
Step 4: Insert the battery connectors and tighten the screws of battery retaining cover
Step 3: Pull the battery trays out slowly and
then put the new battery trays back into the
compartment
Step 5: Install the front panels
19
Copyright © 2011 CyberPower Systems, Inc.
MAINTENANCE
MANUAL BYPASS SWITCH OPERATION
This operation allows qualified personnel to remove the detachable PDU or HW PDU from the Power module for routine maintenance or replacement without
disrupting power to connected equipment.
REMOVE PDU or HW PDU
Step 1: Slide the Interlock Bracket to the left
Step 5: Pull the PDU or HW PDU away from the Power module
Remove the one screw that fix the Interlock Bracket in the right.
Loosen the four screws that hold the PDU or HW PDU to the Power module.
Slide the Interlock Bracket to the left.
Pull the PDU or HW PDU away from the Power module and loosen the two
screws that hold the cover.
Step 6: Fix the cover on the PDU or HW PDU
Step 2: Check the Power module auto transfer to Manual Bypass
After Sliding the Interlock Bracket to the left, the Power module will auto
transfer to Manual Bypass. Check that the LCD screen shows “Manual
Bypass” before turning the “Manual Bypass Switch“ to “Bypass“.
Tighten the two screws and fix the cover on the PDU or HW PDU to hide the
connectors.
Step 3: Turn the “Manual Bypass Switch“ to “Bypass“
The Power module shutdown safely and it can perform routine
maintenance or replacement now.
Step 4: Press “ON/OFF“ button to turn off UPS
SAFETY PRECAUTIONS
CAUTION! It must be done by qualified personnel to prevent from the risk
of fire or electric shock.
CAUTION! Hazardous voltage may exist between the connectors of the
PDU or HW PDU. Do not let the connectors touch any surface.
CAUTION! Do not slide the Interlock Bracket when the LCD screen shows
“Generator On” or “Converter On”.
CAUTION! Do not turn the Manual Bypass Switch when hearing a warning
beep from the Power module.
20
Copyright © 2011 CyberPower Systems, Inc.
MAINTENANCE
REATTACH PDU or HW PDU
Step 1: Remove the cover from the PDU or HW PDU
Step 4: Turn the “Manual Bypass Switch“ to “Normal“
Loosen the two screws and remove the cover from the PDU or HW PDU to
expose the connectors.
Step 5: Slide the Interlock Bracket to the right
Slide the Interlock Bracket to the right.
Step 2: Reattach the PDU or HW PDU to the Power module
Reattach the PDU or HW PDU to the Power module and tighten the two
screws to fix the cover on the PDU or HW PDU.
Tighten the one screw that fix the Interlock Bracket in the right.
Tighten the four screws that hold the PDU or HW PDU to the Power module.
Step 6: Check the Power module auto transfer to Line Mode
Step 3: Press “ON/OFF“ button to turn on UPS in “Manual Bypass”
After Sliding the Interlock Bracket to the right, the Power module will auto
transfer to Line Mode. Check the LCD screen shows “Line Mode”.
SAFETY PRECAUTIONS
CAUTION! It must be done by qualified personnel to prevent from the risk
of fire or electric shock.
CAUTION! Hazardous voltage may exist between the connectors of the
PDU or HW PDU. Do not let the connectors touch any surface.
CAUTION! Do not slide the Interlock Bracket when the LCD screen shows
“Generator On” or “Converter On”.
CAUTION! Do not turn the Manual Bypass Switch when hearing a warning
beep from the Power module.
21
Copyright © 2011 CyberPower Systems, Inc.
TECHNICAL SPECIFICATIONS
Model
Configuration
Capacity (VA)
Capacity (Watts)
Form Factor
Energy-saving Technology
Input
Input Voltage Range
Input Frequency Range
Input Power Factor
Cold Start
Output
Output Waveform
Output Voltage
Output Frequency
Transfer Time (Typically)
Rated Power Factor
Harmonic Distortion
Crest Factor
ECO Mode Voltage Regulation
Outlets for the PDU unit
Outlets for the HW PDU unit
Protection
Surge Protection
Phone / Network Protection
Overload Protection
Short Circuit Protection
Battery
Specifications
Recharge Time (Typically)
Sealed, Maintenance Free
Hot-Swappable
Status Indicators
LCD Screen
LED Indicators
Audible Alarms
Environment
Operating Temperature
Operating Relative Humidity
Management
On-Device Features
Connectivity Ports
SNMP/HTTP Capable
Software
Power Management Software
Physical
Dimensions--Power Module
Dimensions--Battery Module
Net Weight--Power Module
Net Weight--Battery Module
Safety
Conformance Approvals
OL6000RT3UPDU
OL6KRT3UHW
OL8000RT3UPDU
OL8KRT3UHW
OL10000RT3UPDU
OL10KRT3UHW
6000VA
5400W
8000VA
7200W
Rackmount / Tower
Yes, ECO Mode Efficiency > 95%
10000VA
9000W
200~240Vac
40~70Hz
0.99
Yes
Sine wave
200, 208, 220, 230, 240Vac (Configurable) ±2%
50 / 60Hz (Auto-Sensing or Configurable) ±0.25Hz
0ms
0.9
THD < 3% at Linear Load, < 5% at Non-linear Load
3:1
±10%, ±15% (Configurable)
(2) L6-20R, (4) L6-30R, (1) Hard Wire 3-wire
(1) Hard Wire 3-wire
IEC 61000-4-5 Level 3
RJ11/RJ45 (One In/One Out)
Line Mode:
105~125% Load for 1 min,
126~150% Load for 10 sec
Battery Mode: 105~130% Load for 10 sec, 131~150% Load for 2 sec
UPS Output Cut off Immediately or Input Fuse / Circuit Breaker Protection
(20) 12V/7.2AH
4 hours
(20) 12V/9.0AH
5 hours
Yes
Yes
Multi-Function LCD Readout that Supports:
Multi-Language Interface,
(19) Types of Read Out,
(24) Types of Function Setting, (3) Event Logs
Power On (White),
Line Mode (Green),
Battery Mode (Yellow),
Bypass Mode (Yellow), Fault (Red),
Replace Battery (Red)
Battery Mode, Battery Low, Overload, UPS Fault, Replace Battery
32℉ to 104℉ ( 0℃ to 40℃)
0 to 90% Non-Condensing
Self Test, Auto-Charge, Auto-Restart, Auto-Overload Recovery
(1) Serial Port (RS232), (1) USB Port, (1) Remote Control Port, (1) Relay Out
(1) Expansion Port (With optional SNMP card or RMCARD 302)
®
PowerPanel Business Edition
L x W x H = 32.3 x 17 x 5.2in. (82 x 43.3 x 13.2cm)
L x W x H = 32.3 x 17 x 5.2in. (82 x 43.3 x 13.2cm)
63lbs(28.5Kg)
167.2lbs(76Kg)
171.6lbs(78Kg)
CE, UL
22
Copyright © 2011 CyberPower Systems, Inc.
TROUBLE SHOOTING
Problem
Warning
O/P Overload
Load Over XXX%
Battery Mode
Possible Cause
Solution
Your equipment requires more power than the
UPS can provide. If the UPS is in Line Mode
then it will transfer to Bypass Mode; if the UPS is
in Battery Mode it will shutdown.
Your equipment requires more power than the
setting in the Power Management Software
®
(PowerPanel Business) will allow.
BAT Disconnected
Battery Failure
UPS has failed in Battery Test.
Replace Battery
EPO OFF
Wiring Fault
Line Abnormal
Battery will soon need to be replaced due to
insufficient runtime.
Missing the EPO connection.
Contact technical support to replace the battery.
Check the EPO connection.
Exchange line and neutral wires.
Connect ground wire.
No ground wire.
Wrong utility power backed up during UPS autorestart.
Disable Wiring Fault alarm on LCD panel.
Check whether voltage or frequency of utility
power is out of range.
Your attached equipment may have problems,
please remove them and check again.
Check the fan for operation and if the ventilation
hole has been covered.
Over Temperature
High ambient temperature.
Bypass Forbidden
Check battery connector and battery breaker.
1. Check battery connector and battery breaker.
2. Contact technical support to replace the
battery.
Missing ground wire.
Output short circuit.
Autorestart Lock
UPS will restart automatically when acceptable
utility power returns.
Line and neutral wires are reversed.
Output Short
Coldstart Lock
Shut off the non-essential equipment or increase
the level in the Power Management Software.
Save your data and perform a controlledshutdown.
UPS is operating on battery power.
UPS is operating on battery power and will be
shutting down soon due to extremely low battery
voltage.
Missing battery power.
Battery Low
Shut off non-essential equipment. If this solves
the overload problem, the UPS will transfer to
normal operation.
UPS is locked to prevent consuming battery
power during shipping.
“Automatic Restore” is disabled in Power
®
Management Software (PowerPanel Business)
Manual Bypass Forbidden when the LCD screen
shows “Generator On” or “Converter On”.
Plug into utility power for first-time operation.
Press “ON/OFF“ button to turn on UPS
Slide the Interlock Bracket to the right. (For the
PDU or HW PDU only)
Fault
1. Remove battery connector and
charger voltage.
2. Contact CyberPower for repair.
Over Charge
Battery is overcharged.
Charger Failure
Charger has failed.
High O/P V
Output voltage is too high.
Low O/P V
Output voltage is too low.
Bus Fault
Internal DC bus voltage is too high or too low.
check
1. Shut down UPS and turn off input breaker.
2. Contact CyberPower for repair.
CyberPower Systems Inc.
www.cpsww.com
©
Entire contents copyright 2011 CyberPower Systems Inc., All rights reserved. Reproduction in whole or in part
®
®
without permission is prohibited. PowerPanel Business Edition and PowerPanel Personal Edition are trademarks of
CyberPower Systems Inc.
23
Copyright © 2011 CyberPower Systems, Inc.
PRODUCT REGISTRATION
CyberPower requests that you complete and return the Warranty Registration Card enclosed with the Product or register the Product at its website
(www.cpsww.com) to establish that you are the Initial Customer of the Product, and therefore entitled coverage under the Limited Warranty and the Connected
Equipment Guarantee. (Registration is not required for coverage, but note: if you do not register your purchase, you will be required to provide proof of
purchase.)
LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARNTEE
Read the following terms and conditions carefully before using the CyberPower OL6000RT3UPDU / OL8000RT3UPDU / OL10000RT3UPDU / OL6KRT3UHW
/ OL8KRT3UHW / OL10KRT3UHW. By using the Product you consent to be bound by and become a party to the terms and conditions of this Limited
Warranty and Connected Equipment Guarantee (together referred to as this “Warranty”). If you do not agree to the terms and conditions of this Warranty, you
should return the Product for a full refund prior to using it.
Who is Providing this Warranty?
CyberPower Systems (USA), Inc. (“CyberPower”) provides this Limited Warranty.
What Does This Warranty Cover?
This warranty covers defects in materials and workmanship in the Product under normal use and conditions. It also covers equipment that was connected to
the Product and damaged because of the failure of the Product.
What is the Period of Coverage?
This warranty covers the Product for three years and connected equipment for as long as you own the Product.
Who Is Covered?
This warranty only covers the original purchaser. Coverage ends if you sell or otherwise transfer the Product.
How Do You Get Warranty Service?
1. Before contacting CyberPower, identify Your Product model number, the Purchase Date, and each item of Connected Equipment.
2. Email us at tech@cpsww.com or Call us at (877) 297-6937.
3. If your product requires warranty service you must provide a copy of your dated purchase receipt or invoice.
How Do You Open A Connected Equipment Claim?
1. Call us at (877) 297-6937 or write to us at Cyber Power Systems (USA), Inc., 4241 12th Ave. E., STE 400, Shakopee, MN 55379, or send us an e-mail
message at claims@cpsww.com for instructions, within 10 days of the occurrence.
2. When you contact CyberPower, identify the Product, the Purchase Date, and the item(s) of Connected Equipment. Have information on all applicable
insurance or other resources of recovery/payment that are available to the Initial Customer and Request a Claim Number.
3. You must provide a dated purchase receipt (or other proof of the original purchase) and provide a description of the damage to your connected equipment.
4. Pack and ship the product to CyberPower and, if requested, the item(s) of Connected Equipment, a repair cost estimate for the damage to the Connected
Equipment, and all claim forms that CyberPower provides to you. Show the Claim Number on the shipping label or include it with the product. You must
prepay all shipping costs, you are responsible for packaging and shipment, and you must pay the cost of the repair estimate.
How Long Do I Have To Make A Claim?
All claims must be made within ten days of the occurrence.
What Will We Do To Correct Problems?
CyberPower will inspect and examine the Product.
If the Product is defective in material or workmanship, CyberPower will repair or replace it at CyberPower's expense, or, if CyberPower is unable to or decides
not to repair or replace the Product (if defective) within a reasonable time, CyberPower will refund to you the full purchase price you paid for the Product
(purchase receipt showing price paid is required).
If it appears that our Product failed to protect any equipment plugged into it, we will also send you forms for making your claim for the connected equipment.
We will repair or replace the equipment that was damaged because of the failure of our Product or pay you the fair market value (NOT REPLACEMENT
COST) of the equipment at of the time of the damage. We will use Orion Blue Book, or another a third-party valuation guide, or eBay, craigslist, or other
source to establish that amount. Our maximum liability is limited to $300,000 for OL6000RT3UPDU / OL8000RT3UPDU / OL10000RT3UPDU /
OL6KRT3UHW / OL8KRT3UHW / OL10KRT3UHW.
24
Copyright © 2011 CyberPower Systems, Inc.
LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARNTEE
Who Pays For Shipping?
We pay when we send items to you; you pay when you send items to us.
What Are Some Examples Of What This Warranty Does Not Cover?
1. This Warranty does not cover any software that was damaged or needs to be replaced due to the failure of the Product or any data that is lost as a result of
the failure or the restoration of data or records, or the reinstallation of software.
2. This Warranty does not cover or apply to: misuse, modification, operation or storage outside environmental limits of the Product or the equipment
connected to it, nor for damage while in transit or in storage, nor if there has been improper operation or maintenance, or use with items not designed or
intended for use with the Product, such as laser printers, appliances, aquariums, medical or life support devices, etc.
What Other Limitations Apply?
The sole and exclusive remedies of the Initial Customer are those provided by this Warranty.
1. This Warranty does not apply unless the Product and the equipment that was connected to it were connected to properly wired and grounded outlets
(including compliance with electrical and safety codes of the most current electrical code), without the use of any adapters or other connectors.
2. The Product must have been plugged directly into the power source and the equipment connected to the Product must be directly connected to the Product
and not “daisy-chained” together in serial fashion with any extension cords, another Product or device similar to the Product, surge suppressor, or power tap.
Any such installation voids the Limited Warranty.
3. The Product and equipment connected to it must have been used properly in a suitable and proper environment and in conformance with any license,
instruction manual, or warnings provided with the Product and the equipment connected to it.
4. The Product must have been used at all times within the limitations on the Product’s VA capacity.
The Product was designed to eliminate disrupting and damaging effects of momentary (less than 1ms) voltage spikes or impulses from lightning or other
power transients. If it can be shown that a voltage spike lasting longer than 1ms has occurred, the occurrence will be deemed outside the rated capabilities of
the Product and the Limited Warranty is void. CyberPower Does Not Cover or Undertake Any Liability in Any Event for Any of the Following:
1. Loss of or damage to data, records, or software or the restoration of data or records, or the reinstallation of software.
2. Damage from causes other than AC Power Line Transients, spikes, or surges on properly installed, grounded and code-compliant 120 volt power lines in
the United States and Canada; transients, surges or spikes on standard telephone land lines, PBX telephone equipment lines or Base 10T Ethernet lines,
when properly installed and connected. (This exclusion applies, for example, to fluctuations in data transmission or reception, by CATV or RF transmission or
fluctuations, or by transients in such transmission.)
3. Damage from any circumstance described as excluded above with respect to the Product.
4. Damages from fire, flood, wind, rain, rising water, leakage or breakage of plumbing, abuse, misuse or alteration of either the product or the Connected
Equipment.
5. CyberPower excludes any liability for personal injury under the Limited Warranty and Connected Equipment Guarantee. CyberPower excludes any liability
for direct, indirect, special, incidental or consequential damages, whether for damage to or loss of property [EXCEPT FOR (AND ONLY FOR) the specific
limited agreement of CyberPower to provide certain warranty benefits regarding "Connected Equipment" under this Warranty], loss of profits, business
interruption, or loss of information or data. NOTE: Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation may not apply to you.
6. The Product is not for use in high-risk activities or with aquariums. The Product is not designed or intended for use in hazardous environments requiring
fail-safe performance, or for use in any circumstance in which the failure of the Product could lead directly to death, personal injury, or severe physical or
property damage, or that would affect operation or safety of any medical or life support device (collectively, "High Risk Activities"). CyberPower expressly
disclaims any express or implied warranty of fitness for High Risk Activities or with aquariums. CyberPower does not authorize use of any Product in any High
Risk Activities or with Aquariums. ANY SUCH USE IS IMPROPER AND IS A MISUSE OF THE PRODUCT.
Where Can I Get More Information?
The application of the United Nations Convention of Contracts for the International Sale of Goods is expressly excluded.
CyberPower is the warrantor under this Limited Warranty.
For further information please feel free to contact CyberPower at CyberPower Systems (USA), Inc. 4241 12th Ave E., STE 400, Shakopee, MN 55379; call us
at (877) 297-6937; or send us an e-mail message at claims@cyberpowersystems.com.
25
Copyright © 2011 CyberPower Systems, Inc.
CONFORMANCE APPROVALS
FCC Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference that may cause undesired operation.
WARNING!! This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense. Shielded signal cables must be used with this product to ensure compliance with the Class A
FCC limits.
The Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulation.
Cet appareil numerique de la class A respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada.
This document is believed to be accurate, but CyberPower reserves the right to change or correct the contents and does not assume any responsibility for
omissions or errors.
Need Additional Help?
Feel free to contact our Tech Support department with installation, troubleshooting, or general product questions.
CyberPower Technical Support
Phone: 1-877-297-6937
Email: tech@cpsww.com
Web: www.CPSww.com
Mail: 4241 12th Avenue E, Suite 400 Shakopee, MN 55379
Hours of Operation:
Monday – Friday, 8:00am – 5:00pm (CST)
Entire contents copyright © 2011 CyberPower Systems, Inc.
All rights reserved. Reproduction in whole or in part without permission is prohibited.
26
Copyright © 2011 CyberPower Systems, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising