CyberPower | CPS200SU | User manual | CyberPower CPS200SU User Manual

CyberPower CPS200SU User Manual
Power Inverter + USB
CPS200SU
Congratulations on your purchase
Thank you for selecting the CyberPower CPS200SU Power
Inverter + USB. The information contained in this brochure
explains the features and operation of the CPS200SU.
Please take a few moments to read this manual.
Package Contents
• (1) Power Inverter + USB
• (1) Product Registration Card
• (1) User Manual
Features
1. 2 AC Power Outlets (120v)
2. DC Power Plug
3. 2.1 Amp USB Charging Port
4. Power Status Indicator LED
5. High-Speed Cooling Fan
OPERATING & STORAGE
Operating
• DO NOT allow water or other liquids to come into contact
with the inverter.
• Ambient air temperature should be 32°F – 104°F (0°C – 40°C).
Keep inverter out of direct sun light.
• Keep the inverter’s ventilation slot unobstructed to ensure
air flow to the unit. DO NOT place any items on or over
the inverter during operation. The unit will shut down if it
overheats.
Storage
• Proper storage temperature rang is 32°F – 86°F (0°C – 30°C)
• Store the inverter in a cool and dry environment.
• Avoid exposing the inverter to heating elements, direct
sunlight or high humidity when not in use.
SPECIFICATIONS
User Manual
• Model Number: CPS200SU
• Input Voltage: 10.5 to 15.5 Volts
• Output Power: 200 Watts (max)
• Output Voltage: 120 Volts
• Output Frequency: 60Hz
• USB Voltage: 5Vdc
• Output Waveform: Simulated Sine Wave
• Protection Features: Low Voltage, Overheat,
Overload, Short Circuit
Safety Information
• DO NOT operate the CPS200SU near flammable materials,
fumes or gasses.
• Always use the inverter where there is adequate ventilation.
DO NOT obstruct the ventilation slots.
• NEVER immerse the unit in water.
• Proper cooling is essential when operating the inverter.
Refrain from placing the inverter near a vehicle’s heat vent or
in direct sunlight.
• Always turn the inverter off when not in use by removing it
from the DC accessory socket.
• Check the warning labels on battery chargers or adapters
before connecting them to the inverter. DO NOT connect
battery chargers or adapters with warnings about using with
inverters.
TROUBLESHOOTING
Power Inverter does not provide power:
1. Poor contact with DC power outlet
Ensure the inverter is securely plugged into the vehicle’s DC
power outlet.
2. Automotive electrical system requires ignition to be on
Turn vehicle ignition to “Accessory” position.
3. Vehicle DC power outlet fuse is blown
Check vehicle fuse panel and replace damaged fuse.
4. Overheating
Allow inverter to cool. Ensure that there is adequate
ventilation around the unit.
5. Vehicle battery voltage below 10.5 volts
Unplug inverter and start the vehicle to charge the battery.
6. Vehicle battery voltage higher than 15.5 volts
Check your vehicle’s user guide for trouble shooting.
7. Inverter is overloaded
Ensure load does not exceed the units Continuous Power
rating (see specifications).
TECHNICAL SUPPORT
Please contact our Tech Support department with installation,
troubleshooting, or general product questions.
• Phone: 1-877-297-6937
• Email: tech@CPSww.com
• Hours of Operation: Monday – Friday, 8:00am – 5:00pm CST
Limited Warranty
FCC NOTICE
CyberPower warrants this CPS200SU (the “CPS Product”)
to be free from material and manufacturing defects for three
years. If a defect results in product failure during its normal
use, CyberPower’s sole responsibility is to repair or replace
(at its sole option) the CPS Product. IF YOU DO NOT AGREE
TO THE TERMS AND CONDITIONS OF THIS WARRANTY,
YOU SHOULD RETURN THE PRODUCT FOR A FULL REFUND
PRIOR TO USING IT.
This equipment has been tested and found to comply with
the limits for a Class B Digital Device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures: (1) Reorient or relocate the receiving antenna. (2)
Increase the separation between the equipment and receiver.
(3) Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected. (4) Consult the
dealer or an experienced radio/TV technician for help. Any
special accessories needed for compliance must be specified
in the instruction.
Who is Providing this Warranty, Who is Covered?
What Does It Cover? And for How Long?
CyberPower Systems (USA), Inc. (“CyberPower”) provides this
Limited Warranty. It only covers the original purchaser and ends
if you no longer own the CPS Product. This warranty covers
defects in materials and workmanship in the CPS Product
under normal use and conditions. This warranty covers the CPS
Product for as long as you own the CPS Product.
1. Call (877) 297-6937 or write to CyberPower, 4241 12th Ave.
E., STE 400, Shakopee, MN 55379 or send an e-mail to
claims@CPSww.com for instructions.
2. Identify the Product, the Purchase Date.
3. Provide a dated Proof-of-Purchase receipt (or other proof of
the original purchase) and provide a description of the defect.
4. Pack and ship the product to CyberPower, and all claim
forms that CyberPower provides to you. Show the Claim
Number on the shipping label or include it with the product.
You must prepay all shipping costs, you are responsible for
packaging and shipment, and you must pay the cost of the
repair estimate.
5. Do each of these within ten days of the occurrence.
What Will CyberPower Do To Correct Problems?
CyberPower will inspect and examine the CPS Product. If the
CPS Product is defective in material or workmanship,
CyberPower will repair or replace it at CyberPower’s expense,
or CyberPower will refund the full purchase price you paid for
the CPS Product (purchase receipt showing price paid
is required).
CAUTION: A shielded-type power cord is required in order to
meet FCC emission limits and also to prevent interference to
the nearby radio and television reception. It is essential that
only the supplied power cord be used. Use only shielded cables
to connect I/O devices to this equipment.
PRODUCT REGISTRATION
Prompt product registration assures coverage under the
Limited Warranty, and also allows the opportunity to be notified
of
product enhancements, upgrades, and other announcements.
Registration is quick and easy at www.CPSww.com/register.
CONTACT INFORMATION
CyberPower Systems, Inc.
4241 12th Avenue East Suite 400 Shakopee, MN 55379
Toll-free: 1-877-297-6937 | CPSww.com
Please join CyberPower in caring for the
environment by recycling this manual.
© 2012 CyberPower Systems, Inc.
All rights reserved. All other trademarks are the property of their
respective owners.
K01-0000237-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising