Cobra | XRS 777 | Owner Manual | Cobra XRS 777 Radar/Laser Detector User manual

Cobra XRS 777 Radar/Laser Detector User manual
Introduction
Important Information And
Customer Assistance
Important Information
Federal Laws Governing The Use Of Radar Detectors
It is not against federal law to receive radar transmissions with your Cobra radar/
laser detector. The Communications Act of 1924 guarantees your right to receive
radio transmissions on any frequency. Local laws that contravene this Act, while
illegal, may be enforced by your local law enforcement officials until and unless
they are prohibited from doing so by federal court action.
Operating Instructions
The Cobra line of quality products includes:
•
Safety Alert
Use of this product is not intended to, and does not, ensure that motorists or
passengers will not be involved in traffic accidents. It is only intended to alert
the motorist that an emergency vehicle equipped with a Cobra Safety Alert
transmitter is within range as defined by that product. Please call local fire
and police departments to learn if coverage exists in your area.
Safe Driving
Motorists, as well as operators of emergency or service vehicles, are expected to
exercise all due caution while using this product, and to obey all applicable traffic laws.
CB Radios
Security Of Your Vehicle
Before leaving your vehicle, always remember to conceal your radar detector
in order to reduce the possibility of break-in and theft.
microTALK Radios
®
Radar/Laser Detectors
Safety Alert® Traffic Warning Systems
Customer Assistance
Customer Assistance
Accessories
GPS (Global Positioning System)
HighGear® Accessories
For Assistance In The U.S.A.
Automated Help Desk English only. 24 hours a day, 7 days a week 773-889-3087 (phone).
CobraMarine™ VHF Radios
Power Inverters
For more information or to
order any of our products,
please visit our website:
www.cobra.com
Nothing comes close to a Cobra®
•
Should you encounter any problems with this product, or not understand its many features,
please refer to this owner’s manual. If you require further assistance after reading this
manual, Cobra Electronics offers the following customer assistance services:
English
11 BAND™ ULTRA
HIGH-PERFORMANCE
DIGITAL RADAR/LASER
DETECTOR WITH XTREME
RANGE SUPERHETERODYNE™
TECHNOLOGY
XRS 777
Nothing comes close to a Cobra®
Customer Assistance Operators English and Spanish. 8:00 a.m. to 6:00 p.m. CT
Mon. through Fri. (except holidays) 773-889-3087 (phone).
Questions English and Spanish. Faxes can be received at 773-622-2269 (fax).
Technical Assistance English only. www.cobra.com (on-line: Frequently Asked
Questions). English and Spanish. productinfo@cobra.com (e-mail).
Printed in China
Part No. 480-177-P
For Assistance Outside The U.S.A.
Contact Your Local Dealer
A1 English
English
©2004 Cobra Electronics Corporation
6500 West Cortland Street
Chicago, Illinois 60707 USA
www.cobra.com
Introduction
Controls, Indicators,
Connections And Display
Introduction
Controls, Indicators, Connections And Display
Windshield Bracket
Release Button
•
Windshield
Bracket Mount
LaserEye
For 360° detection of
laser and strobe signals.
Auxiliary Audio
Jack
Speaker
12V DC
Power Jack
On-Off/Volume Control
Allows user to adjust the
volume of the tone alerts.
Program/Mute Button
For manual mute of
audio alerts (and to enter
programming mode).
Alpha/Numeric Dot Matrix Text Display*
Shows user mode settings, programming instructions,
signal strength indication, City/Highway mode indicators,
radar, VG-2, Spectre 1 and safety/strobe indicators.
* See pages 5 – 26 for more information
about display features.
A2 English
Set/City Button
For City or Highway modes
to reduce false alerts (and to
change user mode settings
while programming).
Select/Dim Button
Adjusts the display brightness
for easy reading (and to scroll
through user mode settings
while programming).
System Ready
WARNING
Modifications or parts substitutions not approved
by Cobra Electronics Corporation may violate
FCC Rules and void your authority to operate
this equipment.
Product Features
Customer Assistance
Product Features
Congratulations! You’ve made a smart choice by purchasing the XRS 777
ultra high performance digital radar/laser detector from Cobra. Just look at
some of the sophisticated features and capabilities your new unit includes:
Xtreme Range
Superheterodyne Technology
With super-fast sweep circuitry,
XRS provides extra detection range
and the best possible advance warning
to even the fastest radar guns
Ultra Performance
Provides advanced warning with
extra detection range
Detection And Separate Alerts
For radar signals (X, K and Ka bands,
with signal strength indicated), laser
signals, Safety Alert signals, Strobe Alert
signals, VG-2 signals, Spectre 1 signals
8-Point Compass
Displays direction of travel
LaserEye
For 360° detection of laser and
strobe signals
Instant-On Ready
Detects radar guns with “instant-on”
(very fast) speed monitoring capabilities
Pop Detection
Detects the latest super-fast instant-on
signal pulse radar guns
Voice Or Tone Alert
With adjustable volume
DigiView Data Display
With easy-to-read alpha/numeric
dot matrix text readout
•
IntelliShield False Signal Rejection
Reduces falsing in urban areas with
Highway mode and three (3) levels
of City mode settings
Safety Alert
Traffic warning system distinguishes
important safety alerts from other
K band signals
Strobe Alert
Emergency vehicle warning system
Manual Mute Or Auto Mute
A mute function of audio alerts
IntelliMute
A mute function which automatically
reduces false alerts by sensing engine
RPMs
Smart Power
A timed power saving function that
saves your car’s battery
EasySet Programming
User-friendly mode selection and
setting with visual guidance
Auxiliary Audio Jack
For external speaker connection
Mounting
Mounts easily on windshield
or dashboard
This booklet describes the simple steps for mounting and setting up your detector.
It also provides helpful information about how radar and laser guns are used and
how you can interpret the alerts you receive.
Nothing comes close to a Cobra® A3
Order Form
Order Form
•
Name
Address (No P.O. Boxes)
City
State/Province
Zip
Country
Telephone
Credit Card Number
Type: ❒ Visa ❒ MasterCard ❒ Discover
Exp. Date
Customer Signature
Item #
Description
420-030-N-001
420-026-N-001
545-139-N-001
CLP-2B
Straight 12V Power Cord
Coiled 12V Power Cord
Windshield Mounting Bracket
Dual Port Power Adapter
U.S. Cost Each
Qty
Amount
U.S. Subtotal
Amount Shipping/Handling* Tax Table
Wisconsin add 5%
$10.00 or less . . . . . $3.00
(Tax if Applicable)
Indiana, Michigan,
$10.01-$25.00 . . . . . $5.50
Ohio add 6%
$25.01-$50.00 . . . . . $7.50
California add 7.25%
Shipping/Handling
Illinois add 8.75%
$50.01-$90.00 . . . . $10.50
Total
$90.01-$130.00 . . . $13.50 *For AK, HI and PR add additional $26.95 for FedEx Next Day or
$10.95 for FedEx 2nd Day. Excludes weekends and holidays shipments.
$130.01-$200.00 . . $16.50
Please allow two (2) to three (3) weeks for delivery in the U.S.A.
$200.01 plus . . . . . 10% of
purchase
Prices subject to change without notice.
Ordering From U.S.A.
Call 773-889-3087 for pricing or visit www.cobra.com.
For Credit Card Orders
Complete and return this order form to fax number 773-622-2269. Or call 773-889-3087
[Press one (1) from the main menu] 8:00 a.m. to 6:00 p.m. CT, Monday through Friday.
Make Check or Money Order Payable To
Cobra Electronics, Attn: Accessories Dept.,
6500 West Cortland Street, Chicago, IL 60707 U.S.A.
To Order Online
Please visit our website: www.cobra.com
Nothing comes close to a Cobra®
37
Your Detector
Installation
Your Detector
Installation
Where To Mount Your Unit
•
You will get optimum performance from your detector if you Mount it at a
point approximately in the center of the vehicle, as low as possible on the
front windshield without obstructing the unit’s view of the road either to
the front or rear. You can also mount it directly on the dashboard.
Windshield Mounting
Dashboard Mounting
Installation
Windshield Mounting
1. Attach the rubber
cups to the bracket.
2. Make sure the rubber cups and your windshield are clean.
3. Push the bracket firmly
onto the windshield.
The unit’s lens must not be blocked and the LaserEye should have a clear view
out the back window to allow 360 ° detection.
The LaserEye Should Have A Clear View
4. Attach the detector to
the bracket. Check the
angle of the unit.
5. To adjust the angle if
necessary, gently push or
pull on the bracket to bend
it. DO NOT use the detector
to bend the bracket.
6. Plug the power cord
into the detector.
Radar and laser signals pass through glass but not through other materials
and objects. Objects that can block or weaken incoming signals include:
Windshield wiper blades
Mirrored sun screens
Dark tinting at the top of the windshield
Heated windshields currently available on some vehicles
(Instaclear for Ford, Electriclear for GM). Consult your dealer
to see if you have this option.
2
English
7. Plug the cigarette lighter
adapter on the power
cord into your vehicle’s
cigarette lighter.
8. You can temporarily remove the detector whenever you
wish by depressing the bracket release button and sliding
it off the bracket.
Nothing comes close to a Cobra®
3
Installation
Your Detector
Getting Started
Getting Started
Dashboard Mounting
On-Off/
Volume Control
Rotate clockwise
(away from you)
1. Place the detector on the dashboard to find a location
where the unit has a clear, level view of the road.
The angle CANNOT be adjusted after mounting.
ns
Ico
nd
co
3. Attach the pad to the
dashboard at your chosen
location and remove the
other paper backing.
To Turn On The Unit And Adjust The Audio Volume
Se
2. Remove the paper backing
from one (1) side of the
hook-and-loop fastener.
Rotate the On-Off/
Volume control
clockwise (away
from you).
Power On
Testing
7. Plug the cigarette lighter
adapter on the power
cord into your vehicle’s
cigarette lighter.
4
English
Tone
Visual Display
Voice
Three (3) beeps
Testing
Testing, then three
(3) beeps
System Ready
System Ready
The display will then
cycle through the
Voice Alert
user mode settings
(city or highway,
Intellimute and
SmartPower status).
Start-up is complete when the display continuously shows the
current compass direction (N, NE, E, SE, S, SW, W or NW) plus
single letters indicating current user mode settings ( c = City
mode, City X Beep Off mode and City X+K mode, h = Highway
mode, i = IntelliMute on).
4. Attach the detector to the
hook-and-loop fastener.
You can remove and
reattach the unit as
often as you like.
6. Plug the power cord
into the detector.
•
ary
Your Detector
System Ready
Voice Alert
Start-Up Complete
NW
h
NOTE
In some vehicles, power is supplied to the cigarette
lighter even while the ignition is off. If this is the case
with your vehicle and you have turned the SmartPower
off, you should turn off or unplug your detector when
parking for lengthy periods. Cobra recommends leaving
SmartPower at the factory setting, which is on.
Nothing comes close to a Cobra®
5
Your Detector
EasySet Programming
EasySet Programming
All user mode settings on your detector can be changed by using
Program mode. When changing the settings, please keep in mind:
Buttons can have multiple functions.
All settings will be stored in memor y when the power is
turned off and recalled when the power is turned back o n.
The procedure for using Program mode is shown on page 7.
NOTE
You cannot enter Program mode during an alert. The unit will not detect
signals while in Program mode. During programming, if no buttons are
pushed for ten (10) seconds, the unit will automatically exit Program
mode and save the last settings.
Programming User Modes
The tables on pages 8 through 9 show you how to program all user modes
and the settings you can choose from.
NOTE
On the following pages, you will find more detailed
explanations of each setting.
See page 15 for instructions on setting the IntelliMute activation point.
See page 17 for instructions on calibrating the compass.
See page 22 for instructions on using SmartPower.
Your Detector
•
EasySet Programming
Set/City Button
Press and release
Select/Dim Button
Press and release
Program/Mute Button
Press and hold/Press and release
To Use Program Mode
Press and hold the
Program/Mute button
for two (2) seconds.
Voice
Three (3)
beeps
Program will appear.
Start Program
PROGRAM
While the programming
instructions are
scrolling, press and
release the Select/Dim
button to cycle through
the user modes.
One (1) beep As each mode is displayed,
with each
the current setting for that
button press mode will be shown.
None
With the user mode you
wish to change displayed,
press and release the
Set/City button to
change the setting.
One (1)
or two (2)
beeps,
depending
on your
selection
Current
setting
When you have finished
programming any or
all of the user modes,
press and release the
Program/Mute button
to exit Program mode.
Or simply wait ten (10)
seconds without
pushing any buttons.
English
Visual Display
Then brief programming
instructions will scroll
through the display three
(3) times.
To move to the next
selection, press the
Select/Dim button again.
6
Tone
The setting you
select will be shown.
One (1) beep When you exit Program
Exit Program
mode, the new setting
will automatically be saved
and EXIT PROGRAM and
Settings Saved! will appear.
EXIT
Settings
PROGRAM
Saved!
Nothing comes close to a Cobra®
7
Your Detector
EasySet Programming
This EasySet programming menu lists all of the modes and settings
you can choose from after you have entere d Program mode as
described on page 7.
EasySet Programming Menu
Mode
Tone Or Voice Visual Setting Result
Set City
mode
default*
Two (2) beeps City X
IntelliMute
mode
One (1) beep
City X
beep Off
Audio for all X band alerts are blocked
until signal strength reaches Level 3.
One (1) beep
City X+K
Combines the City X mode with
prevention of K band audio alerts
until signal strength reaches Level 2.
Two (2) beeps IntelliMute On All alerts (except for strobe signals
from emergency vehicles) are
automatically muted below the
engine rev point you set.
One (1) beep
Set IntelliMute One (1) beep
RPMs
(not shown
if IntelliMute
is off)
AutoMute
mode
Set compass
Pop Detect
mode
8
English
A single beep sounds when the
signal is first detected.
IntelliMute Off Normal operation.
Set IntelliMute Allows you to set the engine
(see page 15
rev point while using IntelliMute.
to set activation
point)
Two (2) beeps AutoMute On
The audio volume of all alerts will be
automatically muted after four (4) seconds
for as long as the signal is detected.
One (1) beep
AutoMute Off
All alerts will sound at full volume
for as long as the signal is detected.
One (1) beep
Set Compass
(see page 17
to calibrate
compass)
Allows you to calibrate the compass.
Two (2) beeps Pop Detect On The unit will detect Pop signals.
One (1) beep
Pop Detect Off The unit not will detect Pop signals.
Your Detector
EasySet Programming
EasySet Programming Menu
Mode
Tone Or Voice Visual Setting Result
VG-2 Detect
mode
Two (2) beeps VG-2 Detect On The unit will detect VG-2 signals.
One (1) beep
VG-2 Detect Off The unit will not detect VG-2 signals.
VG-2 Audio
Two (2) beeps VG-2 Audio On With VG-2 Detect on, the unit will give
mode (not
audible alerts for VG-2 signals.
shown if VG-2
One (1) beep VG-2 Audio Off With VG-2 Detect off, the unit will give
detect is off)
only visual alerts for VG-2 signals.
Spectre 1
Detect mode
Two (2) beeps Spectre 1
Detect On
The unit will detect Spectre 1 signals.
Spectre 1
Detect Off
The unit will not detect Spectre 1 signals.
Spectre 1
Audio mode
(not shown if
Spectre 1
detect is off)
Two (2) beeps Spectre 1
Audio On
With Spectre 1 Detect on, the unit will
give audible alerts for Spectre 1 signals.
Spectre 1
Audio Off
With Spectre 1 Detect off, the unit will give
only visual alerts for Spectre 1 signals.
SmartPower
mode
Two (2) beeps SmartPower
On
SmartPower is on.
SmartPower
Off
SmartPower is off.
One (1) beep
One (1) beep
One (1) beep
X Band detect Two (2) beeps X Band On
mode
One (1) beep X Band Off
Set display
Dim mode
default*
Two (2) beeps Display Dim
The unit will detect X Band signals.
The unit will not detect X Band signals.
Partially dimmed for dusk or night driving.
One (1) beep
Display
Dimmer
More dimmed for dusk or night
driving.
One (1) beep
Display Dark
Display is off.
Restore
factory
settings
One (1) beep
Restore
Factory
Settings
Resets user modes and settings to
factory default.
Exit program
One (1) beep
EXIT
PROGRAM
Allows you to exit Program mode.
* The settings for these user modes can also be changed with the one (1) button method.
See description of each user mode (pages 10 and 24) for details.
Nothing comes close to a Cobra®
9
Your Detector
Settings
Your Detector
Settings
Highway/City Mode
•
Your detector has a Highway mode and three (3) different levels of City
modes: City X, City X Beep Off and City X+K. City X mode sounds a single
beep when the signal is first detected. City X Beep Off mode prevents all
X band audio alerts until the signal strength reaches Level 3. City X+K mode
combines the City X mode with prevention of K band audio alerts until the
signal strength reads Level 2. This will reduce false alerts while you are
driving in or near urban areas where there are many sour ces for conflicting
X or K band signals such as microwave towers and automatic door openers.
The factory setting is Highway. The factory City mode default setting is City X.
Settings
Setting City Default
You can set the default level for City mode (City X, City X Beep Off and
City X+K) either in Program mode or directly using the Set/City button.
City X
City
X+K
Press and
hold the
Set/City
button City X
Beep Off
Set/City Button
Press and hold
To Set The City Mode Default Directly Using The Set/City Button
Set/City Button
Press and release
To Change From Highway Mode To City Mode
Press and
release the
Set/City button.
City Mode
NW
c
Tone
Visual Display
Voice
One (1) beep
c appears in
the display
City X or City X Beep
Off or City X, K
NOTE
When you change to City mode, the unit will enter
whichever city default mode is set at the time.
Highway Mode
NW
Tone Or Voice
Visual Display
One (1) beep each time
the display cycles
Cycles — see chart above
Release the Set/City
button to select the
current display as
default.
None
City X Beep Off,
City X+K or City X
To Set The City Mode Default Using Program Mode
(See Page 7 For Instructions On Using Pr ogram Mode)
In Program mode,
go to City.
To Change From City Mode Back To Highway Mode
Press and release Tone
the Set/City
Two (2) beeps
button again.
Press and hold the
Set/City button.
Visual Display
Voice
h appears in
the display
Highway
Tone
Visual Display
Voice
One (1) beep
City X Beep Off
City X Beep Off
One (1) beep
City X+K
City X, K
Two (2) beeps
City X
City X
City X Beep Off
h
City X
City X+K
City X
City X+K
City X
Beep Off
10 English
Nothing comes close to a Cobra® 11
Your Detector
Settings
Muting An Alert
Your detector allows you to quickly turn off an Audio Alert by momentarily
pressing the Program/Mute button. If you press the Program/Mute button
a second time during the Alert, the Audio Alert will be turned back on.
Voice Alert And Tone Alert Modes
You can set your detector to sound alerts and confirm user settings with
either a Voice or a Tone. The factory setting for Alert mode is V oice.
To Select Voice Or Tone Mode Using Program Mode
(See Page 7 For Instructions On Using Pr ogram Mode)
In Program mode,
go to Voice/Tone.
Program/Mute Button
Press and release
To Turn Turn Off Or On An Audio Alert Using The Program/Mute Button
Press and release
the Program/Mute
button.
Tone
Visual Display
None
None
Tone
Visual Display
Voice
One (1) beep
Tone
Tone Alert
Voice Alert
Voice
Voice Alert
Auxiliary Audio Jack
Auto Mute Mode
Auto Mute will automatically reduce the audio volume of all alerts after
four (4) seconds for as long as the signal is detected. The factor y setting
for Auto Mute is on.
The Auxiliary Audio Jack can be used to connect an external speaker
in environments with high ambient noise levels. The internal speaker
will be disconnected.
To Turn Auto Mute Off Or On Using Pr ogram Mode
(See Page 7 For Instructions On Using Pr ogram Mode)
In Program mode,
go to Auto Mute.
12 English
Tone
Visual Display
Voice
One (1) beep
Auto Mute Off
Auto Mute Off
Two (2) beeps
Auto Mute On
Auto Mute On
Auto Mute Off
Auto Mute On
AutoMute Off
AutoMute On
Auxiliary
Audio Jack
Nothing comes close to a Cobra® 13
Your Detector
Settings
Your Detector
IntelliMute
IntelliMute is a unique new feature that allows you to avoid alerts you
don’t need to hear because you are stopped or moving slowly . By sensing
the “revs” (RPMs) of your engine, IntelliMute knows when you are at low
speed and automatically mutes alerts (except for strobe signals from
emergency vehicles).
Before IntelliMute will work, you must set an activation point for your engine’ s
revs (see page 15). Whenever the revs are below that point, IntelliMute will
begin muting. The activation point will be stored in memor y and recalled
each time the power is turned on. An i will appear in the display when
IntelliMute is on. The factory setting is IntelliMute off.
NOTE
IntelliMute may not work with some vehicles because it cannot sense
the engine’s revs. In such cases, you can reduce unwanted audio alerts
by using Auto Mute and City mode when appropriate.
To Turn IntelliMute On Or Off Using Program Mode
(See Page 7 For Instructions On Using Pr ogram Mode)
In Program mode,
go to IntelliMute.
Tone
Visual Display
Voice
Two (2) beeps
IntelliMute On,
then i appears
in the display
IntelliMute On
One (1) beep
IntelliMute Off
IntelliMute Off
IntelliMute On
NW
IntelliMute Off
ih
Intelli
Intelli
Mute
Mute
Off
Settings
What To Remember While Using IntelliMute
IntelliMute works with all City and Auto Mute modes.
Whenever engine revs are below the activation point, an arrow
pointing down will appear in the display. Above the activation point,
an arrow pointing up will appear.
Below Activation Point
NW
ih
Above Activation Point
NW
ih
If, for any reason, the unit stops sensing your engine’ s revs,
IntelliMute will indicate an error and automatically turn off.
The rev point you set will be stored in the unit’ s memory when
power is turned off and recalled each time the power is turned on.
NOTE
The rev point must be reset if you use your detector in a different vehicle.
NOTE
When initially choosing your IntelliMute activation point, a setting
of approximately 300 to 600 RPMs above idle is recommended.
You can reset the activation point at any time to fit your individual
preferences and driving style.
Setting The IntelliMute Activation Point
Your detector must be installed in your vehicle.
CAUTION
Do not attempt to set the rev point while driving.
Your vehicle should be parked and idling.
IntelliMute must be turned on before setting the activation point.
On
14 English
Nothing comes close to a Cobra® 15
Your Detector
Settings
Your Detector
Set/City
Button
Settings
Compass
To Set The IntelliMute Activation Point Using Program Mode
Your detector includes an internal
8-point Compass that will continuously
display your current direction of travel:
N, NE, E, SE, S, SW, W, or NW.
In Program mode, go to Set
IntelliMute.
Tone
Visual Display Voice
None
Set IntelliMute None
Calibrating The Compass
Press and release the Set/City button
to begin setting IntelliMute RPMs.
Two (2)
beeps
Press SET
at desired
RPMs…
Set Engine
Revs
Rev your engine to the level you wish to
set. Rev the engine slightly above idle and
hold revs steady for two (2) seconds.
None
None
None
At the desired rev level, press and
release the Set/City button.
Three (3)
beeps
IntelliMute
Set!
IntelliMute
Set
Press and release either the
Select/Dim button to proceed to the
next user mode or the Program/Mute
button to exit the Program mode.
None
None
None
Select/Dim Button
Program/Mute Button
(See Page 7 For Instructions On Using Pr ogram Mode)
Setting IntelliMute RRMs
Set Intel...
PressSET...
NOTE
If the unit is unable to sense usable pulses within three (3)
seconds or if you do not set a rev point within 20 seconds
of beginning these steps, IntelliMute will indicate an error
and automatically turn off.
IntelliMute
Tone
Visual Display
Voice
One (1) beep
IntelliMute not set
Please try again
IntelliMute not set
Please try again
IntelliMute Off
IntelliMute Off
One (1) beep
16 English
Not Set
Intelli
Mute
Set!
IntelliMute Off
Intelli
IntelliMu...
Mute
Please tr...
Off
NW
W
SW
N
NE
8-Point
Compass
S
E
SE
NOTE
Before using it for the first time, you must calibrate the compass to
provide accurate indications of direction. See page 7 for instructions
on using the Program mode to select Set Compass.
Calibration allows the compass electronics to measure and store
information about the magnetic fields generated by your vehicle.
The compass will remain accurately calibrated as long as your detector is
mounted in the same place in your vehicle. If you change the location where
the unit is mounted or move it to another vehicle, you must recalibrate the
compass.
The compass temporarily may not provide accurate readings if you are inside
a building or enclosure, or are close to a large metal tractor/trailer , truck, or
train. Once you are away from such a location, the compass will work
correctly again.
NOTE
When the instructions direct you to drive in two (2) cir cles, a large
parking lot is the most convenient place to do so. It does not matter
what direction your vehicle is pointing when you start the cir cles, which
direction you go to make the cir cles, and it does not have to be exactly
two (2) circles. You do NOT have to make per fect circles. You can drive
in any pattern, as long as you make two (2) complete turns. Four (4)
three-point turns, two (2) small squares, or any two (2) complete loops
will work as well as two (2) cir cles. It does not matter what size the
circles are, if your speed is constant, or how fast you make the cir cles
[but less than two (2) minutes]. Please be careful when making the
circles and watch for other traffic.
Nothing comes close to a Cobra® 17
Your Detector
Settings
Your Detector
Pop Alert
Set/City
Button
Select/Dim Button
Pop Alert will alert you of Pop radar signals. During the alert, the unit
continues to detect other signals. The factor y setting is Pop Detect off.
Program/Mute Button
To Calibrate The Compass Using Program Mode
To Turn Pop Detect Mode On Or Off Using Pr ogram Mode
(See Page 7 For Instructions On Using Pr ogram Mode)
(See Page 7 For Instructions On Using Pr ogram Mode)
In Program mode, go to
Set Compass.
Tone
Visual Display Voice
None
Set Compass
Press and hold the Set/City button
to begin setting the compass.
One (1) beep
Drive in 2
Set Compass
circles…
Press SET
when done…
Within two (2) minutes, drive your
vehicle in a circle twice, then press
the Set/City button again.
Three (3)
beeps
Press and release either the Select/Dim None
button to proceed to the next user
mode or the Program/Mute button
to exit Program mode.
Set Compass
Set Compa...
Calibrate
Compass
Settings
In Program mode,
go to Pop Detect.
None
Compass Set! Compass Set
For two (2)
seconds
followed by
direction of
travel (N, NE,
E, SE, S, SW,
W or NW)
None
Compass Set
Drive in...
Compass
Press SET...
Set!
Tone
Visual Display
Voice
Two (2) beeps
Pop On
Ka Pop On
One (1) beep
Pop Off
Ka Pop Off
Pop Detect On
Pop On
Pop Detect Off
Pop Off
None
Direction
Of Travel
N W
h
NOTE
If you do not press the Set/City button within two (2) minutes after beginning
the set compass process, compass calibration will automatically terminate.
Visual Display
One (1) beep
Compass not set… Compass not set…
Compass n...
Please try again… Please try again…
Please tr...
18 English
Voice
Terminate
Tone
Nothing comes close to a Cobra® 19
Your Detector
Settings
Your Detector
VG-2 Alert
The detector is undetectable by VG-2 detection devices and will alert you
when such a device is in use near your vehicle. During the alert, the unit
continues to detect other signals. You can choose whether or not you want
your unit to show VG-2 Alerts. With VG-2 Detect mode on, you can also
choose whether or not you want your unit to sound audible VG-2 Alerts.
The factory settings are VG-2 Detect on and VG-2 Detect Audio on.
Settings
Spectre 1 Alert
The detector is undetectable by Spectre 1 detection devices and will alert you
when such a device is in use near your vehicle. During the alert, the unit
continues to detect other signals. You can choose whether or not you want
your unit to show Spectre 1 Alerts. With Spectre 1 Detect mode on, you can
also choose whether or not you want your unit to sound audible S pectre 1
Alerts. The factory settings are Spectre 1 Detect on, Spectre 1 Audio on.
To Turn VG-2 Detect Mode Off Or On Using Pr ogram Mode
To Turn Spectre 1 Detect Mode Off Or On Using Pr ogram Mode
In Program mode,
go to VG-2 Detect.
In Program mode,
go to Spectre 1 Detect.
(See Page 7 For Instructions On Using Pr ogram Mode)
Tone
Visual Display
Voice
One (1) beep
VG2 Off
VG2 Off
Two (2) beeps
VG-2 Detect Off
VG2 Off
VG2 On
(See Page 7 For Instructions On Using Pr ogram Mode)
VG2 On
VG-2 Detect On
VG2 On
Tone
Visual Display
Voice
One (1) beep
Spectre Off
Spectre Off
Two (2) beeps
Spectre On
Spectre On
Spectre 1 Detect Off
Spectre 1 Detect On
Spectre Off
Spectre On
To Turn VG-2 Audio Mode Off Or On Using Pr ogram Mode
To Turn Spectre 1 Mode Off Or On Using Pr ogram Mode
In Program mode,
go to VG-2 Audio.
In Program mode,
go to Spectre 1 Audio.
(See Page 7 For Instructions On Using Pr ogram Mode)
Tone
Visual Display
Voice
One (1) beep
VG2 Audio Off
VG2 Audio Off
Two (2) beeps
VG-2 Audio Off
...Audio Off
20 English
VG2 Audio On
VG-2 Audio On
...Audio On
VG2 Audio On
(See Page 7 For Instructions On Using Pr ogram Mode)
Tone
Visual Display
Voice
One (1) beep
Spectre Audio Off
Spectre Audio Off
Two (2) beeps
Spectre Audio On
Spectre Audio On
Spectre 1 Audio Off
...Audio Off
Spectre 1 Audio On
...Audio On
Nothing comes close to a Cobra® 21
Your Detector
Settings
Your Detector
SmartPower
Your detector includes the SmartPower feature that, when activated,
will put the unit into Standby mode (low power) for about 30 minutes
after the car’s engine has been turned off. After 30 minutes in Standby
mode, the unit will automatically turn off.
Before SmartPower enters Standby mode, you will hear one (1) beep and
Pwr Save will appear on the display. To return the unit to normal P ower
mode or exit Standby mode, start the car, press any button or turn the unit
off and then on again. The factor y setting is SmartPower on.
DigiView Data Display Brightness
Your detector has a Bright display mode (for daytime driving) and three (3)
levels of Dim display modes (Dim for dusk driving, Dimmer for night driving
and Dark where no visual alerts will be displayed) to control the display’ s
brightness levels. The factory setting is Bright. The factor y Dim mode
default setting is Dimmer.
Dark Indicator
.
SmartPower Entering
Standby Mode
Select/Dim Button
Press and release
Pwr Save
To Turn SmartPower Mode Off Or On Using Pr ogram Mode
(See Page 7 For Instructions On Using Pr ogram Mode)
In Program mode,
go to SmartPower.
Settings
Tone
Visual Display
Voice
One (1) beep
SmartPower Off
SmartPower Off
Two (2) beeps
SmartPower On
SmartPower On
SmartPower Off
SmartPower On
...Power off
To Change The Brightness To Dim
Press and release the
Select/Dim button once.
Dim Display
Dim
Tone
Visual Display
Voice
Two (2) beeps
Dim, Dimmer
or Dark
Dim, Dimmer
or Dark
Dimmer Display
Dimmer
Dark Display
Dark
...Power on
NOTE
When you change to Dim mode, the unit will enter whichever
dim default mode is set at the time.
To Change The Brightness To Bright
Press and release the
Tone
Select/Dim button again.
One (1) beep
Visual Display
Voice
Bright
Bright
Bright Display
Bright
22 English
Nothing comes close to a Cobra® 23
Your Detector
Settings
Your Detector
Setting Dim Default
You can set the default level for D im mode (Dim, Dimmer or Dark)
either in Program mode or directly using the Select/Dim button.
Detection
Signals Detected
Audio Alerts
Press
and hold
Select/Dim
button
Dimmer
Select/Dim Button
Press and hold
Release the Select/Dim
button to select the
current display as
default.
A distinctly different Alert tone is used for each type of signal detected
(including separate tones for each laser signal). For X, K and Ka band
radar signals, the tones will repeat faster as you approach the signal
source. The repeat rate of the tones gives you useful information about
the signal detected. See responding to alerts on page 28.
Visual Display
To Set The Display Dim Mode Default Directly Using The Set/Dim Button
Press and hold the
Select/Dim button
Tone or Voice
Visual Display
One (1) beep each time
the display cycles
Cycles — see chart above
None
Dim, Dimmer or Dark
An indication of the type of signal detected will appear in the DigiView Data
Display. During X, K and Ka alerts, you will also see from one (1) to five (5)
vertical bars, indicating the strength of the signal detected.
Signal Strength Chart
Signal Strength = 1
(Weakest Signal)
-
To Set The Display Dim Mode Default Using Program Mode
(See Page 7 For Instructions On Using Pr ogram Mode)
24 English
Tone
Visual Display
Voice
Two (2) beeps
Dim
Dim
One (1) beep
Dimmer
Dimmer
One (1) beep
Dark
Dark
----
Signal Strength = 3
Signal Strength = 2
1
--
2
---
3
Signal Strength = 5
(Strongest Signal)
Signal Strength = 4
In Program mode,
go to Display Dim,
Dimmer or Dark.
•
The tables on the following pages show you the types of Signals your
detector will detect, as well as the visual alerts it provides for each of them.
Dim
Dark
Detection
4
_
_5
-----
Nothing comes close to a Cobra® 25
Your Detector
Detection
Your Detector
Radar Signals And Visual Displays
Strobe Alert Signals And Visual Displays
Type of Signal
Visual Display
Voice
Type of Signal
Visual Display
Voice
X Band Radar
X and Signal Strength
X Alert
3M Opticom or Tomar*
Emergency Vehicle
Emergency Vehicle Approaching
K Band Radar
K and Signal Strength
K Alert
* Your detector provides 360° detection of these signals.
Ka Band Radar
Ka and Signal Strength
Ka Alert
Pop
Pop Alert
Pop Radar Mode
X Signal Detected
X
Detection
--
K Signal Detected
2
K
---
Ka Signal Detected
3
Strobe Alert Display (Flashing)
Emergency...
Pop Signal Detected
_
-5
Ka----_
Pop
Laser Signals And Visual Displays
Type of Signal
Visual Display
Voice
LTI 20-20*
Laser 20/20
Laser Alert
LTI Ultra-Lyte*
Laser UltraLyte
Laser Alert
Kustom Signals ProLaser*
Laser Pro Laser
Kustom Signals ProLaser III* Laser Pro Laser 3
LTI 20-20
LTI Ultra-Lyte
Visual Display
Voice
Emergency Vehicles
Emergency Vehicle
Emergency Vehicle Approaching
Road Hazards
Road Hazard
Road Hazard Ahead
Trains
Train
Emergency Alert
Signal Detected
Emergency...
Road Hazard Alert
Signal Detected
Train Approaching
Train Alert Signal
Detected
Road
Train
Laser Alert
Kustom Signals
ProLaser III
Laser
Laser
Laser
Laser
20/20
UltraLyte
Pro Laser
Pro Laser 3
NOTE
Beep rate changes with different laser alerts.
Type of Signal
Hazard
Laser Alert
* Your detector provides 360° detection of these signals.
Kustom Signals
ProLaser
Safety Alert Signals And Visual Displays
NOTE
There are different tones for each Safety Alert.
VG-2 And Spectre 1 Aler t Signals And Visual Displays
Type of Signal
Visual Display
Voice
VG-2 Alert
VG2
VG-2 Alert
Spectre 1
Spectre1
Spectre Alert
Spectre 1 Alert
Signal Detected
Spectre1
VG-2 Alert
Signal Detected
VG2
NOTE
There are different tones for each alert.
26 English
Nothing comes close to a Cobra® 27
Your Detector
Detection
Your Detector
Instant-On Detection
Your detector is designed to detect Instant-On speed monitoring signals,
which can suddenly appear at full strength.
NOTE
You should take appropriate action
immediately whenever an instant-on alert is given.
Pop Detection
Your detector is designed to detect single pulse mode radars. These radars
are designed to have a low probability of detection. Y ou should note that these
radar guns have a much shorter range while in this mode.
Responding To Alerts
Description
Interpretation
Recommended
Response
Tone repeats slowly at first,
then speeds up rapidly.
Probably police radar.
FULL ALERT
Tone sounds one (1)
time only.
Probably a false alarm,
but possibly pulsed radar,
Spectre 1 or VG-2 nearby.
Exercise caution
Tone instantly begins
repeating rapidly.
Radar, Spectre 1 or VG-2 nearby
has been activated suddenly.
FULL ALERT
Pop mode tone.
Pop mode gun very close.
FULL ALERT
Tone repeats slowly as you
approach a hill or bridge, then
speeds up sharply as you
reach it.
Probably police
radar beyond the
hill or bridge.
FULL ALERT
Tone repeats slowly
for a short period.
Probably a false alarm.
Exercise caution
Any type of laser alert.
Laser alerts are
never false alarms.
FULL ALERT
Any Safety Alert
or Strobe Alert.
You are nearing an emergency
vehicle, railroad crossing, or
road hazard (construction,
accident, etc.).
Exercise caution
28 English
Understanding Radar And Laser
Understanding Radar And Laser
Radar Speed Monitoring Systems
•
Three (3) band frequencies have been approved by the Federal Communications
Commission (FCC) for use by speed monitoring radar equipment:
X band
10.525 GHz
K band
24.150 GHz
Ka band
33.400 – 36.00 GHz
Your detector detects signals in all three (3) radar bands.
VG-2 And Spectre 1
VG-2 and Spectre 1 are “detector detectors” that work by detecting low-level
signals emitted by most radar detectors. Your detector does not emit signals
that can be detected by VG-2 or Spectre 1, but does detect VG-2 and Spectre 1
signals and will alert you when a device is in use near your vehicle, if you
so choose.
Safety Alert Traffic Warning System
FCC-approved Safety Alert transmitters emit microwave radar signals that
indicate the presence of a safety-related concern. Depending on the frequency
of the signal emitted, it can indicate a speeding emergency vehicle or train,
or a stationary road hazard.
Because these microwave signals are within the K band frequency , most
conventional radar detectors will detect Safety Alert signals as standard
K band radar. Your detector, however, is designed to differentiate between
standard K band and Safety Alert signals, and give separate alerts for each.
Safety Alert technology is relatively new. Safety Alert transmitters can
be found in limited numbers in all 50 states, but the number is growing.
Depending on your location, you may not receive these alerts regularly
and may often encounter emergency vehicles, trains and road hazards
without being alerted. As the number of transmitters increases,
these alerts will become more common.
When you receive such an alert, please watch for emergency vehicles ahead
of you, on cross streets and behind you. If you see an emergency vehicle
approaching, please pull over to the right side of the road and allow it to pass.
Nothing comes close to a Cobra® 29
Your Detector
Understanding Radar And Laser
Strobe Alert
Your Detector
Maintenance
Pop Radar Guns
Special strobes mounted on the light bars of authorized emergency
vehicles (fire trucks, police cars, ambulances) automatically change traffic
signals as the vehicle approaches an intersection. These strobes and the
special strobe detectors located on the traffic signals, introduced fairly
recently by 3M and Tomar, are already in use in more than 1000 cities
nationwide. Cobra’s exclusive Strobe Alert detector will detect these
special strobes and give an emergency vehicle alert.
The Pop mode Radar Gun is a single pulse Doppler radar that is a feature
of a K and Ka (Bee III Ka radar gun) band Instant-On radar gun. It uses a
single short time pulse to measure the target vehicle’ s speed. Despite the fact
that the short, single pulse makes the unit ver y sensitive to officer hand and
vehicle movement and reduces the range of the gun in Pop mode to 50% of
its range in Continuous Wave mode, this feature is added in an attempt to
make the radar gun invisible to Radar Detectors.
When you receive such an alert, please watch for an approaching
emergency vehicle and pull over to allow it to pass. T o inquire about
coverage in your area, contact your local fire and police departments.
Although your detector can sense Pop signals beyond the effective range
of Pop radar guns, there will be a signal to sense only if a gun is triggered.
In addition, the Pop mode receiver section is more prone to false alerts
because of its extra sensitivity. This is especially so in urban areas. As a
result, you should consider using the Pop Detect mode only in highway
and rural situations. Cobra Electronics has included a user selectable on
or off Pop Detect mode.
LIDAR (Laser)
The correct name for the technology that most people refer to as
laser is actually LIDAR, which stands for Light Detection and Ranging.
LIDAR operates much like radar. Its signal spreads out like a radar
signal, though not as widely. Unlike radar, LIDAR must have a clear
line of sight to its target vehicle throughout the entire measurement
interval. Obstructions such as sign posts, utility poles, tree branches,
etc., will prevent valid speed measurement.
Some common questions about LIDAR include:
Does weather have any affect on LIDAR?
Yes. Rain, snow, smoke, fog, or airborne dust particles will reduce the
effective range of LIDAR and can, if dense enough, prevent its operation.
Can LIDAR operate through glass?
Yes. Newer LIDAR guns can obtain readings through most types of glass.
However, the laser pulse also can be received through glass to trigger
an alarm by your detector.
Can LIDAR operate while in motion?
No. Because LIDAR operates by line of sight, the person using it cannot
drive the vehicle, aim and operate the gun all at the same time.
Is LIDAR legal to use?
Yes. It is legal in all 50 states.
30 English
Maintenance
Maintenance Of Your Radar Detector
•
Your detector is designed and built to give you years of trouble-free
performance without the need for ser vice. No routine Maintenance
is required.
If your unit does not appear to be operating properly ,
please follow these troubleshooting steps:
Make sure the power cord is properly connected.
Make sure the socket of your vehicle’s cigarette lighter
is clean and free of corrosion.
Make sure the power cord’s cigarette lighter adapter
is firmly seated in your cigarette lighter.
Check the power cord fuse. (Unscrew the ribbed end cap of
the cigarette lighter adapter and examine the fuse. If required,
replace it with a 2-amp fuse only.)
Nothing comes close to a Cobra® 31
Your Detector
Specifications
Warranty
Specifications
•
Band And Frequencies
Band
Frequencies
X Band
10.525
± 0.050
GHz
K Band
24.125
± 0.125
GHz
Safety Alert
Traffic Warning
System
24.070
± 0.010
GHz
24.110
± 0.010
GHz
24.190
± 0.010
GHz
24.230
± 0.010
GHz
Ka Band
34.700
± 1.300
GHz
Laser
910
± 50
nm
Strobe
700
± 300
nm
Warranty
Limited 1-Year Warranty
•
For Products Purchased In The U.S.A.
Cobra Electronics Corporation warrants that its Cobra 11 Band Radar/Laser
Detectors, and the component parts thereof, will be free of defects in
workmanship and materials for period of one (1) year from the date of first
consumer purchase. This warranty may be enforced by the first consumer
purchaser, provided that the product is utilized within the U.S.A.
Cobra will, without charge, repair or replace, at its option, defective 11 Band
Radar/Laser Detectors, products or component parts upon deliver y to the
Cobra Factory Service Department, accompanied by proof of the date of first
consumer purchase, such as a duplicated copy of a sales receipt.
You must pay any initial shipping charges required to ship the product for
warranty service, but the return charges will be at Cobra’ s expense, if the
product is repaired or replaced under warranty.
This warranty gives you specific rights, and you may also have other rights
which vary from state to state.
Unit Dimensions And Weight
Dimensions* (H x W x D)
Weight*
Exclusions: This limited warranty does not apply:
7
1 ⁄2" x 3 ⁄16" x 4 ⁄8"
6.45 oz.
1. To any product damaged by accident.
(38 mm x 78 mm x 124 mm)
(183 g)
2. In the event of misuse or abuse of the product or as a result
of unauthorized alterations or repairs.
1
1
* Dimensions and weight measurements are approximate.
3. If the serial number has been altered, defaced or removed.
This radar detector is covered by one or more of the following U.S. patents: 5,497,148; 5,594,432;
5,612,685; 6,078,279; 6,094,148; 6,621,447. Additional patents may be listed inside the product
or pending.
4. If the owner of the product resides outside the U.S.A.
All implied warranties, including warranties of mer chantability and fitness for
a particular purpose are limited in duration to the length of this warranty .
Cobra shall not be liable for any incidental, consequential or other damages;
including, without limitation, damages resulting from loss of use or cost of
installation.
Some states do not allow limitations on how long an implied warranty lasts
and/or do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations may not apply to you.
32 English
Nothing comes close to a Cobra® 33
Customer Assistance
Product Service
Product Service
If you have any questions about operation or installing your new
Cobra product, or if you are missing parts…
Customer Assistance
•
Please call Cobra first! DO NOT RETURN THIS PRODUCT
TO THE STORE! See customer assistance on pa ge A1.
If you suspect that your unit requires ser vice, please call 773-889-3087
BEFORE shipping it to Cobra. This will ensure that you receive ser vice
as quickly as possible.
If you are asked to send your unit to the Cobra factor y, please follow
these steps:
1. Send the complete unit, including power cord. (It is not necessar y
to include the mounting bracket.)
2. For warranty repair, enclose some form of proof-of-purchase,
such as a photocopy or carbon copy of a sales receipt. If you
send the original receipt, it cannot be returned.
Trademark Acknowledgement
Trademark Acknowledgement
Cobra, 6 Band, DigiView, Extra Sensory Detection, HighGear, microTALK,
LaserEye, Safety Alert Traffic Warning System, Strobe Alert, VG-2 Alert
and Nothing comes close to a Cobra are registered trademarks of
Cobra Electronics Corporation.
•
Cobra Electronics Corporation, 11 Band, EasySet, IntelliMute, IntelliShield,
Road Ready, SmartPower, Spectre 1 Alert, UltraBright, Voice Alert and Xtreme
Range Superheterodyne are trademarks of Cobra Electronics Corporation.
Opticom is a trademark of 3M Corporation. Instaclear for Ford is a
registered trademark of Ford Motor Company, Inc. Electriclear for GM
is a registered trademark of General Motors Corporation. 20-20 and
Ultra-Lyte are trademarks of Laser Technology, Inc. ProLaser and
ProLaser III are trademarks of Kustom Signals, Inc. Bee III and Pop
are a trademarks of MPH Industries. Spectre is a trademark of Stalcar .
Interceptor VG-2 is a trademark of TechniSonic Industries LTD.
Tomar is a registered trademark of TOMAR Electronics, Inc.
3. Enclose a typed or clearly written description of the problem
you are having with your unit, plus the name and address where
you want the unit returned.
4. Pack the unit securely to prevent damage during transit. If possible,
use the original packing materials.
5. Ship prepaid and insured using a traceable carrier such as United Par cel
Service (UPS), Federal Express, or Priority mail with deliver y confirmation.
Ship to: Cobra Factory Service, Cobra Electronics Corporation, 6500 West
Cortland Street, Chicago, IL 60707 U.S.A.
6. Please allow three (3) to four (4) weeks before contacting us about
the status of your service. Call 773-889-3087 for assistance. If your
unit is under warranty, it will either be repaired or replaced upon receipt,
depending on the model. If your unit is out of warranty , you will receive
a letter informing you of the repair or replacement charge.
34 English
Nothing comes close to a Cobra® 35
Customer Assistance
Optional Accessories
Optional Accessories
You can find quality Cobra products and accessories
at your local Cobra dealer, or in the U.S.A., you can
order directly from Cobra.
Customer Assistance
•
Order Form
Order Form
•
Name
Address (No P.O. Boxes)
City
State/Province
Zip
Country
MasterCard
Discover
Telephone
Credit Card Number
Type:
Visa
Exp. Date
Customer Signature
Straight 12V DC Power Cord
Windshield Mounting Bracket
Includes plug and fuse
Item # 420-030-N-001
Includes suction cups
Item # 545-139-N-001
Item #
Description
420-030-N-001
420-026-N-001
545-139-N-001
CLP-2B
Straight 12V Power Cord
Coiled 12V Power Cord
Windshield Mounting Bracket
Dual Port Power Adapter
U.S. Cost Each
Qty
Amount
U.S. Subtotal
Amount Shipping/Handling* Tax Table
Wisconsin add 5%
$10.00 or less . . . . . $3.00
(Tax if Applicable)
Indiana, Michigan,
$10.01-$25.00 . . . . . $5.50
Ohio add 6%
$25.01-$50.00 . . . . . $7.50
California add 7.25%
Shipping/Handling
Illinois add 8.75%
$50.01-$90.00 . . . . $10.50
Total
$90.01-$130.00 . . . $13.50 *For AK, HI and PR add additional $26.95 for FedEx Next Day or
$10.95 for FedEx 2nd Day. Excludes weekends and holidays shipments.
$130.01-$200.00 . . $16.50
Please allow two (2) to three (3) weeks for deliver y in the U.S.A.
$200.01 plus . . . . . 10% of
purchase
Prices subject to change without notice.
Ordering From U.S.A.
Call 773-889-3087 for pricing or visit www.cobra.com.
Coiled 12V DC Power Cord
Dual Port Power Adapter
Includes plug and fuse
Item # 420-026-N-001
Includes adjustable plug
(up to 90°) and fuse
Item # CLP-2B
36 English
For Credit Card Orders
Complete and return this order form to fax number 773-622-2269. Or call 773-889-3087
[Press one (1) from the main menu] 8:00 a.m. to 6:00 p.m. CT , Monday through Friday.
Make Check or Money Order Payable To
Cobra Electronics, Attn: Accessories Dept.,
6500 West Cortland Street, Chicago, IL 60707 U.S.A.
To Order Online
Please visit our website: www.cobra.com
Nothing comes close to a Cobra®
37
The Cobra line of quality products includes:
CB Radios
microTALK® Radios
Radar/Laser Detectors
Safety Alert® Traffic Warning Systems
Accessories
GPS (Global Positioning System)
HighGear® Accessories
CobraMarine™ VHF Radios
Power Inverters
For more information or to
order any of our products,
please visit our website:
www.cobra.com
Nothing comes close to a Cobra ®
English
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising