Cobra | SH360 | Owner Manual | Cobra ACXT360 Walkie Talkie User manual

Cobra ACXT360 Walkie Talkie User manual
Introduction
Introduction
Staying in touch with your family and friends is convenient
and easy when using your microTALK® radio. Some of the
many uses you will discover include:
Secure your microTALK® radio while on the go.
1
13
14
• Weather Alert
ACXT360
Printed in China
Part No. KEM-ML39900A
English
Battery Low
Using Your Radio
Battery Save Mode
3. Press and hold the Talk button while
speaking into the microphone.
4. When finished talking, release the Talk
button and listen for a response.
• Auto Squelch
8. Volume Up/Down Buttons
9. Light/Max Range Button
10. Talk Button
11. Call Button
12. Wrist Strap Connection
13. Belt Clip
14. Battery Compartment
15. Battery Door Latch
Turning on Your microTALK Radio
®
Press and hold the Mode/Power button until you hear a
series of audible tones indicating the radio is on. Your
microTALK® radio is now in Standby mode, ready to
receive transmissions. The radio is always in Standby
mode except when the Talk, Call or Mode/Power
buttons are pressed.
Two Inches (5 cm)
from Mouth
If there are no transmissions within 10 seconds, the
radio will automatically switch to Power Save mode
and the Power Saver icon will flash in the display.
This will not affect the radio’s ability to receive
incoming transmissions.
Battery Status Indicator
Press the Volume Up or Volume
Down button.
Cobra recommends your radio is turned off while being charged.
Non-rechargeable alkaline batteries can also be used in your radio.
A double beep sound is used to indicate
the minimum and maximum volume levels
(1 through 8).
Operation
Mode Functions
Scrolling Through the Mode Function
By scrolling through the Mode function, you will be able to
select or turn on preferred features of your microTALK® radio. When
scrolling through the Mode function, your radio features
will be displayed in the same predetermined order:
– Press and release the Light/Max Range
button or change channels.
Mode/Power
Lock Function
The Lock function locks the Channel Up, Channel
Down and Mode/Power buttons to prevent
accidental operation.
To turn the lock on or off:
– Press and hold the Lock button for
two seconds.
Press and release the Call button.
Lock Icon
A double beep sound is used to confirm your lock on
or off request. When in Lock mode,
the Lock icon will be displayed.
Your microTALK® radio incorporates two advanced coded squelch
systems that can help to reduce interference from other users
on any given channel. CTCSS (Continuous Tone Coded Squelch
System) provides 38 privacy codes and DCS (Digitally Coded Squelch)
provides 83 privacy codes. This provides a total of 121 Privacy
Codes. Either system can be used on all channels, but both systems
cannot be used on the same channel at the same time.
microTALK Range
Your range will vary depending on terrain and conditions.
Maximum Range
In flat, open country your radio will
operate at maximum range.
Buildings and foliage in the path of the
signal can reduce the range of the radio.
Reduced Range
Auto Squelch/Maximum Range
Your microTALK® radio will automatically shut off weak transmissions
and unwanted noise due to terrain, conditions or if you’ve reached your
Maximum Range limit.
Channel Number
Reduced Range
You can temporarily turn off auto squelch or turn on maximum range
extender, allowing all signals to be received and extending the
maximum range of your radio.
See page 13 for frequency allocations chart.
3
To successfully communicate using a privacy code, both
the sending and receiving radios must be tuned to the same
channel and to the same privacy code system (CTCSS or DCS)
and privacy code number. Each channel will remember the
last privacy code system and number you select.
Dense foliage and hilly terrain will further
reduce the range of the radio.
On FRS Channels 8 through 14, your radio
automatically switches to low power, which
will limit the range the radio can communicate.
The privacy code 00 is not a privacy code, but allows all
signals to be heard on a channel that is set to 00 on both
the CTCSS and DCS systems.
Remember, you can achieve maximum
range by using maximum range extender.
See page 4 for details.
4
Set CTCSS Privacy Codes
Set DCS Privacy Codes
Set Vox On/Off
Set Vox Sensitivity
Set Channel Scan
Set CTCSS Privacy Code Scan
Set DCS Privacy Code Scan
Set Call Tones
Set Roger Beep On/Off
Privacy Codes
®
Press and release the Light/Max Range button
to illuminate the display.
1
To temporarily turn off auto squelch:
To turn maximum range extender off:
With the radio on, select any of the 22 channels by
pressing the Channel Up or Channel Down button.
Both radios must be tuned to the
same channel to communicate.
2
Use only the supplied rechargeable batteries and charger for recharging
your Cobra microTALK® radio.
To turn maximum range extender on:
To Illuminate Display
Light/Max Range
3. Plug the cable into USB-compatible power port.
– Press and hold the Light/Max Range button
for at least five seconds until you hear
two beeps which indicates the maximum
range extender is on.
The other person will hear a three second call
tone. This tone is used only to establish voice
communications.
1. Check to see that the batteries have been
inserted properly.
2. Insert the cable into the charge jack located at
the top of the radio.
Press the Light/Max Range button for
less than five seconds.
See page 11 on how to select between
five call tone settings.
To Select a Channel
The battery charge status is shown on the display.
Four bars indicates fully charged.
Light/Max Range
Release the Talk button to receive incoming
transmissions. Your microTALK® radio is always
in Standby mode while the Talk or Call buttons
are not pressed.
Call Button
Call Button
To charge batteries in radio:
Radio Charger Jack
A-3
Lock Button
1. Press and hold the Talk button.
2. With the microphone about two inches (5 cm) from
your mouth, speak in a normal voice.
3. Release the Talk button when you are
finished talking and listen for a response.
You cannot receive incoming calls while
pressing the Talk button.
• Do not mix alkaline, standard (carbon-zinc), or
rechargeable (Ni-Cd, Ni-MH, etc.) batteries.
Maximum range may vary and is based on
unobstructed line-of-sight communication
under ideal conditions.
• Belt Clip
A-2
Volume Level
Both radios must be tuned to the
same channel to communicate.
Channel Button
• Maximum
Range Extender
To Adjust Volume
Communicating with Another Person
Talk Button
• Battery/Power Saver
• Battery Level
Indicator
1. Antenna
2. External Speaker/
Microphone/Charge Jack
3. Mode/Power Button
4. Weather/Lock Button
5. Channel Up/Down Buttons
6. Backlit LCD Display
7. Speaker/Microphone
4. Replace battery compartment cover and
belt clip.
• Do not mix old and new batteries.
• Keystroke Tones
Volume Button
Insert Batteries
1. Battery Level Indicator
2. VOX Icon
3. Scan Icon
4. Roger Beep Icon
5. Lock Icon
6. Low Power Icon
7. DCS/CTCSS Icons
8. Weather Icon
9. Weather Alert Icon
10. DCS/CTCSS Privacy Code Numbers
11. Power Saver Icon
12. Channel Numbers
13. Receive/Transmit Icon
• Roger Beep
Selectable On/Off
7
11
Auto Battery Save
Both radios must be tuned to the same
channel/privacy code to communicate.
Battery Charge
Status
8
Listening
The radio will display flashing battery icon
while charging if the radio is on.
Quick Start
1. Press and hold the Mode/Power button
to turn on your radio.
2. Press the Channel Up or Channel Down
button to select a channel.
Mode/Power
When battery power is low, the final bar in the
Battery Low icon will blink and an audible tone will
sound twice before the radio shuts off. Your batteries
should be replaced or recharged, if using
rechargeable batteries.
11
10
3. Insert the supplied three AA rechargeable
batteries or non-rechargeable alkaline batteries.
Position batteries according to polarity markings.
• Do not attempt to charge alkaline batteries.
• Speaker/
Microphone/
Charge Jack
Listening for a Response
Battery Low
Operation
Pull Up Lock Latch
7
12
• Button Lock
3
A-1
®
2. Pull up on the battery door latch to remove the
battery compartment cover.
8
13
To install or replace batteries:
1. Remove belt clip by releasing belt clip
latch and sliding clip up.
9
• Call Alert
Five selectable tones
4
9
www.cobrawalkietalkie.com
Nothing Comes Close to a Cobra
Remove Belt Clip
• Backlit LCD Display
5
Customer Assistance
For any questions about operating this new Cobra branded product, PLEASE
CONTACT US FIRST… do not return this product to the retail store. The contact
information for support will vary depending on the country in which you
purchased and utilize the product.
To obtain warranty service or other information for products purchased from
Altis itself or through its authorized reseller or agent and utilized in the U.S.A.,
please call our consumer support line at (866) 721-3805, or email us at
support@altistec.com. You will receive instructions on how to ship the
products at your expense to an Altis Global Limited Authorized Service Center.
To obtain service, you must include: (a) a copy of your receipt, bill of sale or
other comparable proof of purchase; (b) a written description of the problem;
and, most importantly; (c) your address and telephone number.
For warranty and customer service information outside the US, please contact
your local dealer.
For further information needed on its features,
please visit www.cobrawalkietalkie.com
©2018 Altis Global Limited,
for frequently asked questions and the
Atlanta, GA USA.
electronic manual.
Installing Batteries
6
• Scan
Channels, privacy
codes
6
Product Service & Support
5
1
• Hands-Free Operation
(VOX)
10
4
3
• 121 Privacy Codes
(38 CTCSS codes/
83 DCS codes)
15
2
Carrying your microTALK® radio with you is easy when
using the belt clip or optional wrist strap.
2
• 22 Channels
• 10 Channel NOAA All
Hazards Radio
The belt clip easily attaches to your belt, purse, or
backpack.
TWO-WAY RADIO MODEL
Features
12
Communicating with others while hiking, biking, and working; keeping track of
family and friends at a crowded public event; checking with travel companions
in another car; talking with neighbors; arranging meeting spots with others
while shopping at the mall.
Belt Clip
Your microTALK® radio will give you years of trouble-free service
if cared for properly. Handle the radio gently. Keep the radio away from dust.
Never put the radio in water or in a damp place. Avoid exposure to extreme
temperatures.
Product Features
Making Life Easier and Safer
Owner’s Manual
Caring for Your microTALK® Radio
Backlit LCD Display
5
Mode Functions (continued on back side)
6
2. Press using the Channel Up or Channel Down button to select a DCS
privacy code. You can hold the Up or Down button for fast advance.
3. When DCS privacy code is displayed, choose one of the following:
a. Press the Mode/Power button to enter the new setting and proceed to
other functions.
b. Press the Lock button to return to Standby mode.
c. Do not press any buttons for 15 seconds to enter the new settings and to
return to Standby mode.
Operation
Mode Functions (continued)
Set CTCSS Privacy Codes
To select a CTCSS privacy code:
Mode/Power
1. After selecting a channel, press the Mode/Power
button until the CTCSS icon appears and the small
numbers next to the channel number flash on the
display.
Privacy Code
If DCS is turned on at the channel
selected, the display will flash the
CTCSS icon and “OFF.” To switch from
DCS to CTCSS, press the Channel Up
or Channel Down button while the display
is flashing “OFF.” The display will then
show the small numbers flashing and you
will then be able to proceed to step 2.
Channel Button
2. Press using the Channel Up or Channel Down button to select a privacy
code. You can hold the Up or Down button for fast advance.
3. When your desired CTCSS privacy code is displayed, choose one of the
following:
a. Press the Mode/Power button to enter the new setting and proceed to
other functions.
b. Press the Lock button to return to Standby mode.
c. Do not press any buttons for 15 seconds to return to Standby mode.
Set DCS Privacy Codes
To select a DCS privacy code:
Mode/Power
1. After selecting a channel, press the Mode/Power
button until the DCS icon appears and the small
numbers flash on the display (00 through 83).
DCS Privacy Code
1. Press the Weather button until the All Hazards
Radio icon and the currently selected All Hazards
Radio channel are displayed.
Hazards Radio Icon
Channel Button
2. Use the Channel Up or Channel Down
button to change All Hazards Radio channels.
3. The All Hazards Radio icon will continue to
be displayed when All Hazards Radio is on.
4. To exit All Hazards Radio, press and hold the
Weather button.
*National Oceanographic and Atmospheric Administration
Weather (WX) Alert Mode
Turning On the Weather Alert function will allow your radio to
automatically receive NOAA Hazard Alert radio signals and warnings from
designated NOAA broadcast stations. If the radio is turned ON, it will alert
to Weather and other emergency alerts broadcast by NOAA.
This feature is set
to OFF by default.
Mode/Power
Channel Button
Make sure the strongest
Weather channel is selected
for your area using the NOAA
All Hazards Radio Channels
selection in the previous menu.
1. Press the Weather/Lock button until the Weather
Alert icon flashes on the display. The current On
or Off setting is displayed.
2. Press the Channel Up and Channel Down button
to turn Weather Alert On or Off.
Weather Button
3. Press and hold the Weather/Lock button again to
save the new setting and exit the Weather Alert
Mode and return to Standby mode.
12
1. Press the Mode/Power button until the
Scan icon and the channel numbers appear
on the display.
Scan Channels
Select Channel
1. While in Standby mode, press the Channel Up or
Channel Down button to choose the channel on
which you wish to scan privacy codes.
2. Press the Channel Up or Channel Down button to
begin scanning channels.
Mode/Power
The Scan icon will continue to be displayed when
scan is on. Your radio will continue to scan all
channels and stop if an incoming transmission is
detected. Your radio will remain on that channel for
10 seconds.
Scan Privacy Codes
B
C
High
High
High
High
High
High
High
Low
Low
Low
Low
Low
Low
Low
High
High
High
High
High
High
High
High
WARNING: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: 1) This device may not cause harmful interference, and 2) this device must accept any
interference received,including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
13
a. Press the Mode/Power button to
enter the new setting and proceed
to other functions.
Roger Beep Confirmation Tone
Your listener will hear an audible tone when you release the
Talk button. This alerts the other party that you are finished
talking and it is OK for them to speak.
Mode/Power
To turn roger beep on or off:
1. Press the Mode/Power button until the
Roger Beep icon flashes. The current
on or off setting is displayed.
Roger Beep Off
c. Press the Lock button to return to Standby.
2. Press the Channel Up or Channel Down button
to select roger beep on or off.
3. Choose one of the following:
a. Press the Mode/Power button to
return to Standby mode.
Channel Button
c. Press the Lock button to return to Standby.
A = Channel No. for 22 Channel FRS/GMRS Models
B = Frequency in MHz
C = Power Output
462.5625
462.5875
462.6125
462.6375
462.6625
462.6875
462.7125
467.5625
467.5875
467.6125
467.6375
467.6625
467.6875
467.7125
462.5500
462.5750
462.6000
462.6250
462.6500
462.6750
462.7000
462.7250
Channel Button
b. Press the Channel Up or Channel Down button to
resume scanning privacy codes. If you do not press any button
within 10 seconds, your radio will automatically resume scanning
privacy codes.
FRS/GMRS Frequency Allocation and Compatibility
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
3. Choose one of the following:
3. Press the Channel Up or Channel Down button
to begin scanning privacy codes within the
channel you selected.
b. Press the Channel Up or Channel Down button to
resume scanning privacy codes. If you do not press any button
within 10 seconds, your radio will automatically resume scanning
privacy codes.
a. Press and hold the Talk button to communicate on that channel/
privacy code. Your radio will remain on that channel/privacy code
and return to Standby mode.
General Specifications
Call Tone Setting
1. Press the Mode/Power button until the
letter “C” and the current call tone number
(01 through 05) is displayed. The current
call tone will sound for one second.
2. Press the Channel Up or Channel Down button
to hear the other call tone settings.
a. Press and hold the Talk button to communicate on that channel/
privacy code. Your radio will remain on that channel/privacy code
and return to Standby mode.
During scanning (while receiving an incoming transmission),
you can choose from the following:
General Specifications
To change a call tone setting:
2. Press the Mode/Power button until either the
CTCSS or the DCS icon appears on the display
and the Scan icon and the privacy code numbers
flash on the display.
During scanning (while receiving an incoming transmission),
you can choose from the following:
b. Press the Channel Up or Channel Down button to resume
scanning channels.
Operation
Mode/Power
b. Press the Lock button to return to Standby
mode.
a. Press and hold the Talk button to communicate on that channel.
Your radio will remain on that channel and return to Standby mode.
2. Press the Channel Up or Channel Down button to
change the setting.
3. Choose one of the following:
a. Press the Mode/Power button to enter the selected
setting and proceed to other functions.
b. Press the Lock button to return to Standby mode.
A
To scan privacy codes:
During scanning (while receiving an incoming transmission),
you can choose from the following:
IMPORTANT NOTICE:
To turn Weather Alert On or Off:
To scan channels:
8
NOAA* All Hazards Radio Channels
To listen to All Hazards Radio channels:
You can choose between five different Call Tone Settings to transmit
a call alert.
Mode/Power
Channel Button
The current VOX sensitivity level is
displayed with letters “L” and a Number 1
through 5, with Number 5 being the most
sensitive level and Number 1 being the
least sensitive level.
7
Weather Button
Five Call Tone Settings
Your microTALK® radio can automatically scan the Privacy Codes (either
CTCSS 01 through 38 or DCS 01 through 83) within one channel. Only
one set of privacy codes (CTCSS or DCS) can be scanned at a time.
c. Press the Lock button to return to Standby.
Channel Button
You can use your microTALK® radio to listen to NOAA All Hazards Radio
channels transmitting in your area.
Privacy Code Scan
Your microTALK® radio can automatically scan channels.
The radio ignores specific privacy
codes while scanning channels.
To set VOX sensitivity:
1. Press the Mode/Power button until the VOX icon
flashes and the current sensitivity level is displayed.
Mode/Power
VOX Sensitivity Level
If CTCSS is turned on at the channel selected,
the display will flash the DCS icon and “OFF.”
To switch from CTCSS to DCS, press the
Channel Up or Channel Down button while
the display is flashing “OFF.” The display will
then show the small numbers flashing and
you will then be able to proceed to step 2.
Channel Button
Voice Activated Transmit (VOX)
In VOX mode, your microTALK® radio can be used “hands-free,” automatically
transmitting when you speak. You can set the VOX sensitivity level to fit the volume
of your voice and avoid transmissions triggered by background noise.
To turn VOX mode on or off:
Mode/Power
1. Press the Mode/Power button until the VOX icon
flashes on the display. The current On or Off setting is
displayed.
VOX Icon
2. Press the Channel Up or Channel Down button to turn
VOX On or Off.
3. Choose one of the following:
a. Press the Mode/Power button to enter the new
Channel Button
setting and proceed to other functions.
b. Press the Lock button to return to Standby mode.
Channel Scan
9
Safety Information for microTALK Radios
Your wireless handheld portable transceiver contains a low power transmitter. When the talk button
is pushed, it sends out radio frequency (RF) signals. The device is authorized to operate at a duty
factor not to exceed 50%. In August 1996, the Federal Communications Commissions (FCC) adopted
RF exposure guidelines with safety levels for handheld wireless devices
Important
FCC RF Exposure Requirements: For body-worn operation, this radio has been tested and meets the
FCC RF exposure guidelines when used with Cobra accessories supplied or designated for this
product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Use
only the supplied antenna. Unauthorized antennas, modifications or attachments could damage the
transmitter and may violate FCC regulations.
Normal Position
Hold the transmitter approximately 2 inches from your face and speak in a normal voice, with the
antenna pointed up and away.
FCC Part 15.21 Warning StatementNOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT
EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS
COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
IC RSS-GEN
This device complies with ISEDC license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
The applicant is responsible for providing proper instructions to the user of the radio device, and any
usage restrictions, including limits of exposure durations. The user manual shall provide installation
and operation instructions, as well as any special usage conditions, to ensure compliance with SAR
and/or RF field strength limits. For instance, compliance distance shall be clearly stated in the user
manual.
Radiation Exposure Statement:
Any Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
For Remote controller, SAR tests are conducted using standard operating positions accepted by the
FCC/ISEDC with the device transmitting at its highest certified power level in all tested frequency
bands, although the SAR is determined at the highest certified power level, the actual SAR level of
the device while operating can be well below the maximum value.
Before a new model device is a available for sale to the public, it must be tested and certified to the
FCC that it does not exceed the exposure limit established by the FCC/ISEDC, Tests for each device
are performed in positions and locations (e.g. at the ear and worn on the body) as required by the
FCC/ISEDC.
For body worn operation, this model device has been tested and meets the FCC/ISEDC RF exposure
guidelines when used with an accessory designated for this product or when used with an accessory
that Contains no metal and that positions the handset a minimum of 10 mm from the body.
Non-compliance with the above restrictions may result in violation of RF exposure guidelines.
MODEL ACXT360:
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: 1) This device may not cause harmful interference, and 2) this device
must accept any interference received,including interference that may cause undesired
operation.
FCC Warnings: Replacement or substitution of transistors, regular diodes or other parts
of a unique nature, with parts other than those recommended by Cobra may cause a
violation of the technical regulations of part 95 of the FCC rules, or violation of type
acceptance requirements of part 2 of the rules.
14
b. Press the Lock button to return to Standby
mode.
10
Warranty & Trademark Acknowledgment
Limited One-Year Warranty
Altis Global Limited warrants to the original consumer purchaser only that this product and
the component parts thereof, will be free from defects in workmanship and materials for a
period of one year from the date of first consumer purchase. During this period, Altis will,
repair or replace, at its sole option and discretion, this product or any defective parts. Altis’
liability hereunder shall be limited to repair or replacement of the defective part or parts,
and such correction shall constitute a fulfillment of all of Altis’ warranties hereunder.
This limited warranty is only valid for the original consumer purchaser in limited
jurisdictions and is not transferrable. This limited warranty will automatically terminate
prior to expiration if this product is sold or otherwise transferred to another party. The
product must be purchased from Altis or an authorized dealer or the warranty is void. This
limited warranty is valid only for products purchased and utilized in specific jurisdictions.
Please visit our website at www.cobrawalkietalkie.com for a list of jurisdictions wherein
this limited warranty is valid.
This limited warranty does not cover damage due to misuse, abuse, negligence, acts of
God, accident, commercial use or modification of, or to any part of this product. This
warranty does not cover damage due to improper operation, maintenance or installation;
ordinary wear and tear; or attempted alterations or repairs by anyone other than Altis or
someone authorized by Altis to do warranty work. Any unauthorized alterations or repairs
will void this warranty. This limited warranty does not cover product sold AS IS or WITH ALL
FAULTS. This limited warranty is invalid if the factory applied serial number or date stamp
has been altered, defaced or removed from this product. This limited warranty does not
cover product purchased or utilized in a jurisdiction not covered.
The procedure for obtaining service and support, and the applicability of this warranty, will
vary depending on the country or juristiction in which you purchase and utilize the product.
For details on obtaining product service, support and other warranty information please visit
www.cobrawalkietalkie.com.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state and country to country.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, ALTIS MAKES NO OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. ALTIS EXPRESSLY
DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED
WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS
EXPRESSED WARRANTY.
LIMITATION OF REMEDIES AND DAMAGES. REPAIR OR REPLACEMENT AS PROVIDED
UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. ALTIS SHALL
NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT
LIMITED TO ATTORNEYS’ FEES AND/OR COSTS OF LITIGATION, FOR BREACH OF ANY
EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. ALTIS IS NOT LIABLE FOR ANY
DAMAGES CAUSED BY THE PRODUCT OR BY THE PRODUCT TO PERFORM, INCLUDING ANY
15
11
LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGES, OR CONSEQUENTIAL DAMAGES.
ALTIS IS NOT LIABLE FOR ANY CLAIM MADE BY A THIRD PARTY OR MADE BY YOU FOR A
THIRD PARTY. THIS LIMITATION APPLIES WHETHER DAMAGES ARE SOUGHT, OR A
CLAIM MADE, UNDER THIS WARRANTY OR AS A TORT CLAIM (INCLUDING NEGLIGENCE
OR STRICT PRODUCT LIABILITY), A CONTRACT CLAIM, OR ANY OTHER CLAIM. THIS
LIMITATION CANNOT BE WAIVED OR AMENDED BY ANY PERSON. THIS LIMITATION OF
LIABILITY WILL BE EFFECTIVE EVEN IF ALTIS OR AN AUTHORIZED REPRESENTATIVE OF
ALTIS HAS BEEN ADVISED BY YOU OF THE POSSIBILITY OF ANY SUCH DAMAGES.
Some states and countries do not allow limitations on how long an implied warranty lasts
and do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitations may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state and country to
country.
Provided that the product was purchased from Altis itself or through its authorized
reseller or agent and utilized in the U.S.A., Altis will, without charge, repair or replace, at
its option, defective products, products or component parts upon delivery to the
authorized Altis Global Limited Authorized Service Center, accompanied by proof of the
date of first customer purchase, such as a duplicated copy of a sales receipt.
You must pay any initial shipping charges required to ship the product for warranty
service, but the return charges, to an address in the U.S.A, will be at Altis’ expense, if the
product is under warranty.
For Products Purchased Outside The U.S.A.
Please contact your authorized local reseller or agent for warranty information.
Trademark Acknowledgment
Manufactured, distributed, or sold by Altis Global Limited, official licensee for this
product. Cobra®, microTalk®, Nothing Comes Close to a Cobra®, and the snake design
are registered trademarks of Cobra Electronics Corporation, USA. Cobra Electronics
Corporation™ is a trademark of Cobra Electronics Corporation, USA. All other product or
service names are the property of their respective owners.
©Cobra Electronics Corporation, USA 2018. All rights reserved.
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising