Cobra | ACXT645 | Owner Manual | Cobra ACXT645 Walkie Talkie User manual

Cobra ACXT645 Walkie Talkie User manual
Introduction
Making Life Easier and Safer
Product Features
Staying in touch with your family and friends is convenient
and easy when using your microTALK® radio. Some of the
many uses you will discover include:
Owner’s Manual
Secure your microTALK® radio while on
the go.
Belt Clip
• 10 Channel
Weather Radio
6
TWO-WAY RADIO MODEL
ACXT645
Printed in China
Part No. KEM-ML40200B
English
Nothing Comes Close to a Cobra
®
Battery Low
Battery Low
Listening
Volume Button
Auto Battery Save
Battery Save Mode
Talk Button
Two Inches (5 cm)
from Mouth
Lock Icon
Press and release the Call button.
LED/S.O.S. Flashlight
To Select a Channel
See page 17 for frequency
allocations charts.
A-2
3. Plug the cable into USB-compatible power port.
Turning on Your microTALK® Radio
Use only the supplied rechargeable batteries and charger for recharging
your Cobra microTALK® radio.
Mode/Power
A-3
Mode Functions
Scrolling Through the Mode Function
By scrolling through the Mode function, you will be able to select or turn on
preferred features of your microTALK® radio. When scrolling through the
Mode function, your radio features will be displayed in the same
predetermined order:
Mode/Power
The Lock function locks the Channel Up, Channel
Down, Volume Up, Volume Down and Mode/Power
buttons to prevent accidental operation.
To turn the lock on or off:
– Press and hold the Call/Lock button for two seconds.
A double beep sound is used to confirm your lock on
or off request. When in Lock mode,
the Lock icon will be displayed.
In flat, open country your radio will
operate at maximum range.
Dense foliage and hilly terrain will further
reduce the range of the radio.
1
Privacy Code
Privacy Code
Channel Button
Set CTCSS Privacy Codes
Set DCS Privacy Codes
Set Vox On/Off
Set Vox Sensitivity
Set Call Tones 1-10
Set VibrAlert On/Off
Set Roger Beep On/Off
Set Key Tones On/Off
If DCS is turned on at the channel
selected, the display will flash the
CTCSS icon and “OFF.” To switch from
DCS to CTCSS, press the Channel Up
or Channel Down button while the display
is flashing “OFF.” The display will then
show the small numbers flashing and you
will then be able to proceed to step 2.
Channel Button
2. Press using the Channel Up or Channel Down button
to select a privacy code. You can hold the Up or
Down button for fast advance.
3. When your desired CTCSS privacy code is displayed,
choose one of the following:
a. Press the Mode/Power button to enter the new
setting and proceed to other functions.
b. Press the Talk or Call/Lock button to enter the
new setting and return to Standby mode.
c. Do not press any buttons for 15 seconds to enter
the new setting and return to Standby mode.
Remember, you can achieve maximum
range by using maximum range extender.
See page 4 for details.
If CTCSS is turned on at the channel selected,
the display will flash the DCS icon and “OFF.”
To switch from CTCSS to DCS, press the
Channel Up or Channel Down button while
the display is flashing “OFF.” The display will
then show the small numbers flashing and
you will then be able to proceed to step 2.
2. Press using the Channel Up or Channel Down button
to select a DCS privacy code. You can hold the Up or
Down button for fast advance.
3. When DCS privacy code is displayed, choose one of
the following:
a. Press the Mode/Power button to enter the new
setting and proceed to other functions.
b. Press the Talk or Call/Lock button to enter the
new setting and return to Standby mode.
c. Do not press any buttons for 15 seconds to enter
the new settings and to return to Standby mode.
Mode Functions (continued on back side)
To successfully communicate using a privacy code, both
the sending and receiving radios must be tuned to the same
channel and to the same privacy code system (CTCSS or DCS)
and privacy code number. Each channel will remember the
last privacy code system and number you select.
Reduced Range
2
Set DCS Privacy Codes
To select a DCS privacy code:
Mode/Power
1. After selecting a channel, press the Mode/Power
button until the DCS icon appears and the small
numbers flash on the display (00 through 83).
Set CTCSS Privacy Codes
To select a CTCSS privacy code:
Mode/Power
1. After selecting a channel, press the Mode/Power
button until the CTCSS icon appears and the small
numbers next to the channel number flash on
the display.
Operation
Press and hold the Mode/Power button until you hear
a series of audible tones indicating the radio is on.
Your microTALK® radio is now in Standby mode,
ready to receive transmissions. The radio is always in
Standby mode except when the Talk, Call or
Mode/Power buttons are pressed.
Non-rechargeable alkaline batteries can also be used in your radio.
To temporarily turn off auto squelch:
On Channels 8 through 14, your radio
automatically switches to low power, which
will limit the range the radio can communicate.
4
3. Press and hold the Talk button while
speaking into the microphone.
4. When finished talking, release the Talk
button and listen for a response.
2. Insert the cable into the charge jack located at
the top of the radio.
Maximum range may vary and is based on
unobstructed line-of-sight communication
under ideal conditions.
The privacy code 00 is not a privacy code, but allows all
signals to be heard on a channel that is set to 00 on both
the CTCSS and DCS systems.
You can temporarily turn off auto squelch or turn on maximum range
extender, allowing all signals to be received and extending the maximum
range of your radio.
3
Both radios must be tuned to the same
channel/privacy code to communicate.
Cobra recommends your radio is turned off while being charged.
Buildings and foliage in the path of the
signal can reduce the range of the radio.
Your microTALK® radio will automatically shut off weak transmissions and
unwanted noise due to terrain, conditions or if you’ve reached your
Maximum Range limit.
Channel Number
To charge batteries in radio:
1. Check to see that the batteries have been
inserted properly.
Your microTALK® radio incorporates two advanced coded squelch systems
that can help to reduce interference from other users on any given channel.
CTCSS (Continuous Tone Coded Squelch System) provides 38 privacy codes
and DCS (Digitally Coded Squelch) provides 83 privacy codes. This provides
a total of 121 Privacy Codes. Either system can be used on all channels,
but both systems cannot be used on the same channel at the same time.
Auto Squelch/Maximum Range
Both radios must be tuned to the
same channel to communicate.
Radio Charger Jack
Privacy Codes
Reduced Range
Quick Start
1. Press and hold the Mode/Power button to turn on your radio.
2. Press the Channel Up or Channel Down button to select
a channel.
• Do not mix alkaline, standard (carbon-zinc), or
rechargeable (Ni-Cd, Ni-MH, etc.) batteries.
Your range will vary depending on terrain and conditions.
Press and release the LED flashlight button below the
TALK button to use the LED flashlight located at the
bottom of the radio.
3. Insert the supplied three AA rechargeable
batteries or non-rechargeable alkaline batteries.
Position batteries according to polarity markings.
• Do not mix old and new batteries.
microTALK® Range
Maximum Range
To activate S.O.S. function, press and hold the LED
flashlight button to turn on. Press and release to
turn off the flashlight or S.O.S. function.
With the radio on, select any of the 22 channels by
pressing the Channel Up or Channel Down button.
• Belt Clip
Lock Function
See page 12 on how to select between
ten call tone settings.
LED/S.O.S. Flashlight
• Maximum
Range Extender
– Press and release the Max Range Hi/Lo button or
change channels.
The other person will hear a two second call tone.
This tone is used only to establish voice
communications.
Both radios must be tuned to the
same channel to communicate.
Channel Button
Press the Volume Up or Volume Down button.
A double beep sound is used to indicate the minimum
and maximum volume levels
Call Button
1. Press and hold the Talk button.
2. With the microphone about two inches (5 cm) from
your mouth, speak in a normal voice.
3. Release the Talk button when you are
finished talking and listen for a response.
You cannot receive incoming calls while
pressing the Talk button.
10. Push-to-Talk Button
11. Memory/Escape Button
12. Max Range Hi/Lo Button
13. Scan Button
14. Wrist Strap Connection
15. Belt Clip
16. Battery Compartment
17. Battery Door Screw
18. Rubberized Grips
19. LED Flashlight
20. Weather Button
• Auto Squelch
– Press and hold the Max Range Hi/Lo button for at
least five seconds until you hear two beeps which
indicates the maximum range extender is on.
To turn maximum range extender off:
Lock Button
Call Button
• Low Battery
Audible Alert
19
Volume Level
Communicating with Another Person
• Battery Level Indicator
Press the Max Range Hi/Lo button for less than five
seconds.
To turn maximum range extender on:
(1 through 8).
If there are no transmissions within 10 seconds, the
radio will automatically switch to Battery Save mode
and the Power Saver icon will flash in the display.
This will not affect the radio’s ability to receive
incoming transmissions.
• Battery/Power Saver
• Keystroke Tones
1. Antenna
2. External Speaker/
Microphone/ USB Charge Jack
3. Mode/Power Button
4. Call/Lock Button
5. Channel Up/Down Buttons
6. Backlit LCD Display
7. Speaker/Microphone
8. Volume Up/Down Buttons
9. LED Light Button
2. Using a flat head screw driver or edge of a coin
(a quarter may be used), remove the screw
securing the back battery panel.
• Do not attempt to charge alkaline batteries.
1. Battery Level Indicator
2. Roger Beep Icon
3. VOX Icon
4. Weather Icon
5. Lock Icon
6. Hi/Low Power Icon
7. DCS/CTCSS Icons
8. Scan/Memory Icon
9. Weather Alert Icon
10. DCS/CTCSS Privacy Code Numbers
11. Power Saver Icon
12. Channel Numbers
13. Receive/Transmit Icon
14. Memory Channel Number
15. VibrAlert® / Call Alert Icon
16. Key Tone Icon
• Roger Beep
Selectable On/Off
7
To install or replace batteries:
4. Replace battery compartment cover, screw and
belt clip.
• Speaker/
Microphone/
Charge Jack
18
Light/Max Range
14
Insert Batteries
• Button Lock
3
4
Release the Talk button to receive incoming
transmissions. Your microTALK® radio is always in
Standby mode while the Talk or Call buttons are
not pressed.
10
Remove Screw
• Call Alert
Five selectable tones
5
8
To Adjust Volume
The radio will display flashing battery icon
while charging if the radio is on.
• Backlit LCD Display
20
Listening for a Response
When battery power is low, the final bar in the
Battery Low icon will blink and an audible tone will
sound twice before the radio shuts off. Your batteries
should be replaced or recharged, if using
rechargeable batteries.
Remove Belt Clip
• LED Flashlight
Customer Assistance
For any questions about operating this new Cobra branded product, PLEASE
CONTACT US FIRST...do not return this product to the retail store. The
contact information for support will vary depending on the country in which
you purchased and utilize the product.
To obtain warranty service or other information for products purchased from
Altis itself or through its authorized reseller or agent and utilized in the
U.S.A., please call our consumer support line at (866) 721-3805, or email us
at support@altistec.com. You will receive instructions on how to ship the
products at your expense to an Altis Global Limited Authorized Service
Center. To obtain service, you must include: (a) a copy of your receipt, bill of
sale or other comparable proof of purchase; (b) a written description of the
problem; and, most importantly; (c) your address and telephone number.
For warranty and customer service information outside the US, please
contact your local dealer.
For further information needed on its features,
please visit www.cobrawalkietalkie.com
©2018 Altis Global Limited,
for frequently asked questions and the
Atlanta, GA USA.
electronic manual.
www.cobrawalkietalkie.com
A-1
12 15 11
• Scan
Channels, privacy codes
17
For charging microTALK radio(s) in desktop charger:
1. Insert radio(s) into desktop charger as shown.
2. Insert the micro-USB cable into jack on back of charger.
3. Plug the cable into USB-compatible power port. For
pluggable equipment, the socket-outlet shall be
installed near the equipment and shall be easily
accessible.
If charging light is not on, check position of radio. Radio should be
upright. The charge indicator light will stay on as long as the radio is in
the charging well, and the light will go off when the charging is complete.
Note: To charge a single radio, you can bypass the desktop charger and
simply insert the micro-USB’s connector directly into the charge jack
located on the top of the radio.
The radio will display flashing battery icon while charging.
Cobra recommends your radio be turned off while being charged.
Non-rechargeable alkaline batteries can also be used in your radio.
Installing Batteries
8
13
• VibrAlert® Silent Paging
9
Product Service & Support
9
16
7
Using Your Radio
1. Remove belt clip by releasing belt clip
latch and sliding clip up.
• Hands-Free Operation
(VOX)
12
10
The belt clip easily attaches to your belt, purse, or
backpack.
5
Operation
Your microTALK® radio will give you years of trouble-free service
if cared for properly. Handle the radio gently. Keep the radio away from
dust. Never put the radio in water or in a damp place. Avoid exposure to
extreme temperatures.
• 121 Privacy Codes
(38 CTCSS codes/
83 DCS codes)
13
Carrying your microTALK® radio with you is easy
when using the belt clip or optional wrist strap.
4
6
• Weather Alert
16
2
11
3
1
• 22 Channels
14
1
2
Features
15
Communicating with others while hiking, biking, and working; keeping track
of family and friends at a crowded public event; checking with travel
companions in another car; talking with neighbors; arranging meeting spots
with others while shopping at the mall.
Caring for Your microTALK® Radio
Backlit LCD Display
Introduction
5
6
7
8
10 Memory Location
Your microTALK® radio has 10 Memory Locations for storing your most
frequently used channels and channel/privacy code combinations.
These Memory Locations can be selected individually or can be scanned.
(See page 18 for memory location scan.)
Operation
Mode Functions (continued)
Voice Activated Transmit (VOX)
MEM/Esc Button
In VOX mode, your microTALK® radio can be used “hands-free,” automatically
transmitting when you speak. You can set the VOX sensitivity level to fit the
volume of your voice and avoid transmissions triggered by background noise.
Mode/Power
1. Press the MEM/ESC button. Memory icon and the
Memory Location show on the display.
To turn VOX mode on or off:
Channel Button
1. Press the Mode/Power button until the VOX
icon flashes on the display. The current On or Off
setting is displayed.
VOX Icon
Channel Button
Mode/Power
Channel Button
MEM/Esc Button
Channel Button
Memory Channel
4. Press the Channel Up or Channel Down button to
select the memory location.
You can use your microTALK radio to listen to NOAA All Hazards Radio
channels transmitting in your area.
a. Press and hold the Talk button to communicate on that channel.
Your radio will remain on that channel and return to Memory
Standby mode.
Hazards Radio Icon
c. Press and hold the Scan button to return to Memory Standby.
Your microTALK® radio can automatically scan the Privacy Codes (either
CTCSS 01 through 38 or DCS 01 through 83) within one channel. Only one
set of privacy codes (CTCSS or DCS) can be scanned at a time.
To scan privacy codes:
1. While in Standby mode, press and release the Scan
button twice (CTCSS) or three times (DCS)until the
CTCSS or DCS icon and numbers are flashing.
Select Channel
The Scan icon will continue to be displayed when
privacy code scan is on. Your radio will continue to
scan privacy codes and stop as an incoming
transmission is detected. Your radio will remain on
that channel/privacy code for 10 seconds.
2. Use the Channel Up or Channel Down button to
change All Hazards Radio channels.
4. To exit All Hazards Radio, press and hold the
Weather button until On or Off is displayed.
*National Oceanographic and Atmospheric Administration
Weather (WX) Alert Mode
Turning On the Weather Alert function will allow your radio to
automatically receive NOAA weather signals and warnings from
designated weather broadcast stations. If the radio is turned ON, it will
alert to Weather and other emergency alerts broadcast by NOAA.
a. Press the Mode/Power button to enter the new
setting and proceed to other functions.
Make sure the strongest Weather channel is selected for your
area using the channel selection in the previous menu.
Call Tone On/
Vibrate On
Call Tone On/
Vibrate Off
1. Press the Weather/Lock button twice until the
Weather Alert icon flashes on the display. The
current On or Off setting is displayed.
b. Press Talk or Call/Lock button to enter the new
setting and return to Standby mode.
c. Do not press any buttons for 15 seconds to enter
the new setting and return to Standby mode.
Channel Button
2. Press the Channel Up and Channel Down button
to turn Weather Alert On or Off.
3. Press and hold the Weather/Lock button again to
save the new setting and exit the Weather Alert
Mode and return to Standby mode.
15
16
To change call settings:
1. Press the Mode button until the Call Setting icon
flashes on the display. The current setting (“01”
vibrate + ring, “02” ring only) is displayed.
Frequency Allocation and Compatibility
A = Channel No. for 22 Channel Models
B = Frequency in MHz
C = Power Output
A
B
C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
462.5625
462.5875
462.6125
462.6375
462.6625
462.6875
462.7125
467.5625
467.5875
467.6125
467.6375
467.6625
467.6875
467.7125
462.5500
462.5750
462.6000
462.6250
462.6500
462.6750
462.7000
462.7250
High
High
High
High
High
High
High
Low
Low
Low
Low
Low
Low
Low
High
High
High
High
High
High
High
High
Channel Button
b. Press Talk or Call/Lock button to enter the new
setting and return to Standby mode.
17
During scanning (while receiving an incoming transmission), you can
choose from the following:
a. Press and hold the Talk button to communicate on that channel. Your
radio will remain on that channel and return to Standby mode.
When Key Tone is On, an audible tone will sound each time a button is
pressed.
b. Press the Channel Up or Channel Down button to resume scanning
channels.
Channel Button
3. Choose one of the following:
c. Press and hold the Scan button to return to Standby.
To turn key tone on or off:
1. Current key tone status On/Off will flash.
Memory Scan
2. Press the Channel Up or Channel Down button to
select key tone on or off.
Your microTALK® radio can automatically scan memory channels.
Scan Button
3. Choose one of the following:
b. Press Talk or Call/Lock button to enter the new
setting and return to Standby mode.
c. Do not press any buttons for 15 seconds to enter
the new setting and return to Standby mode.
12
MODEL ACXT645:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: 1) This device may not cause harmful interference, and 2)
this device must accept any interference received,including interference that may
cause undesired operation.
FCC Warnings: Replacement or substitution of transistors, regular diodes or other
parts of a unique nature, with parts other than those recommended by Cobra may
cause a violation of the technical regulations of part 95 of the FCC rules, or violation of
type acceptance requirements of part 2 of the rules.
18
To scan Memory channels:
1. Press and release the Scan button while you are
on Memory Standby mode until the Scan Mem
starts flashing.
a. Press the Mode/Power button to enter the new
setting and return to Standby mode.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Safety Information for microTALK Radios
Your wireless handheld portable transceiver contains a low power transmitter. When the talk button is
pushed, it sends out radio frequency (RF) signals. The device is authorized to operate at a duty factor not
to exceed 50%. In August 1996, the Federal Communications Commissions (FCC) adopted RF exposure
guidelines with safety levels for handheld wireless devices
Important
FCC RF Exposure Requirements: For body-worn operation, this radio has been tested and meets the FCC
RF exposure guidelines when used with Cobra accessories supplied or designated for this product. Use of
other accessories may not ensure compliance with FCC RF exposure guidelines. Use only the supplied
antenna. Unauthorized antennas, modifications or attachments could damage the transmitter and may
violate FCC regulations.
Normal Position
Hold the transmitter approximately 2 inches from your face and speak in a normal voice, with the antenna
pointed up and away.
FCC Part 15.21 Warning StatementNOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY
APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE
USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
IC RSS-GEN
This device complies with ISEDC license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Under ISEDC regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by ISEDC. To reduce potential radio interference to
other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for successful communication.
The applicant is responsible for providing proper instructions to the user of the radio device, and any
usage restrictions, including limits of exposure durations. The user manual shall provide installation and
operation instructions, as well as any special usage conditions, to ensure compliance with SAR and/or RF
field strength limits. For instance, compliance distance shall be clearly stated in the user manual.
Radiation Exposure Statement:
Any Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
For Remote controller, SAR tests are conducted using standard operating positions accepted by the
FCC/ISEDC with the device transmitting at its highest certified power level in all tested frequency bands,
although the SAR is determined at the highest certified power level, the actual SAR level of the device
while operating can be well below the maximum value.
Before a new model device is available for sale to the public, it must be tested and certified to the FCC
that it does not exceed the exposure limit established by the FCC/ISEDC, Tests for each device are
performed in positions and locations (e.g. at the ear and worn on the body) as required by the FCC/ISEDC.
For body worn operation, this model device has been tested and meets the FCC/ISEDC RF exposure
guidelines when used with an accessory designated for this product or when used with an accessory that
Contains no metal and that positions the handset a minimum of 10 mm from the body.
Non-compliance with the above restrictions may result in violation of RF exposure guidelines.
The Scan icon will continue to be displayed when scan
is on. Your radio will continue to scan all channels and
stop if an incoming transmission is detected. Your radio
will remain on that channel for 10 seconds.
Key Tone On/Off
Mode/Power
2. Press the Channel Up or Channel Down button to
change the call setting.
2. Press and hold the Scan button to begin scanning
channels.
The radio ignores specific privacy
codes while scanning channels.
c. Do not press any buttons for 15 seconds to enter
the new setting and return to Standby mode.
c. Do not press any buttons for 15 seconds to enter
the new setting and return to Standby mode.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and 2) this device must accept any interference
received,including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
To turn Weather Alert On or Off:
Channel Button
b. Press Talk or Call/Lock button to enter the
new setting and return to Standby mode.
11
Scan Channels
2. Press the Channel Up or Channel Down button to
select roger beep on or off.
a. Press the Mode/Power button to enter the new
setting and proceed to other functions.
a. Press the Mode button to enter the new setting
and proceed to other functions.
IMPORTANT NOTICE:
Weather Button
3. Choose one of the following:
a. Press the Mode/Power button to enter the new
setting and proceed to other functions.
To scan channels:
1. Press and release the Scan button until the Scan
icon and the channel numbers appear on the display.
3. Choose one of the following:
Your microTALK® radio can alert you to incoming signals by sounding an
audible call tone, by vibrating silently or both.
General Specifications
To listen to All Hazards Radio channels:
1. Press the Mode/Power button until the Roger Beep
icon flashes. The current on or off setting is displayed.
VibrAlert and Call Alert
Operation
This feature is set to OFF by default.
During scanning (while receiving an incoming
transmission), you can choose from the following:
Scan Privacy Codes
Channel Button
Roger Beep Off
Scan Button
To turn roger beep on or off:
®
A memory location can be reprogrammed
at any time it is displayed. Press the
MEM/ESC button to begin.
3. The All Hazards Radio icon will continue to be
displayed when All Hazards Radio is on.
Privacy Code Scan
2. Press the Channel Up or Channel Down button to
hear the other call tone settings.
3. Press and hold the MEM/ESC button to return to
Standby mode on the selected memory location.
1. Press the Weather button once until the All Hazards
Radio icon and the currently selected All Hazards
Radio channel are displayed.
b. Press the Channel Up or Channel Down button to resume scanning
channels.
Channel Button
Channel Button
®
Weather Button
Mode/Power
Call Tone Setting
1. Press the Mode/Power button until the letter “C”
and the current call tone number (01 through 10)
is displayed. The current call tone will sound for
three seconds.
c. Do not press any buttons for 15 seconds to enter
the new setting and return to Standby mode.
If a location has been programmed before,
its associated channel/privacy code will
be shown on the display.
10
NOAA* All Hazards Radio Channels
To change a call tone setting:
b. Press Talk or Call/Lock button to enter the
new setting and return to Standby mode.
2. Press the Channel Up or Channel Down button to
select a memory location (0 through 9).
a. Press the Channel Up or Channel Down button
to select a CTCSS privacy code (00 through 38)
for the channel.
During scanning (while receiving an incoming transmission), you can
choose from the following:
Mode/Power
1. Press the MEM/ESC button until the Memory icon
and the memory location number flash on the
display.
Memory Channel
6. Press the Channel Up or Channel Down button to
select a channel (1 through 22).
9
Your microTALK® radio can automatically scan channels.
To recall a stored memory channel location:
b. Press the MEM/ESC button to switch from CTCSS
to DCS. The DCS icon and privacy code numbers
will flash on the display. The Channel Up or
Channel Down button can then be used to select a
DCS privacy code (00 through 83) for the channel.
2. Press the Channel Up or Channel Down
button to change the setting.
3. Choose one of the following:
a. Press the Mode/Power button to enter the
new setting and proceed to other functions.
b. Press the Talk or Call/Lock button to enter the
new setting and return to Standby mode.
c. Do not press any buttons for 15 seconds to enter
the new setting and return to Standby mode.
2. Press and hold the Scan button to begin scanning
privacy codes within the selected channel.
MEM/Esc Button
8. Choose one of the following:
Channel Button
You can choose between ten different Call Tone Settings to transmit
a call alert.
Channel Button
7. Press the MEM/ESC button. The CTCSS icon and
privacy code numbers will flash on the display.
The current VOX sensitivity level is
displayed with letters “L” and a Number 1
through 5, with Number 5 being the most
sensitive level and Number 1 being the
least sensitive level.
Channel Scan
Your listener will hear an audible tone when you release the Talk button.
This alerts the other party that you are finished talking and it is OK for them
to speak.
b. Press and hold the MEM/ESC button to save the current state of the
Set Memory Function and return to Standby mode.
3. Press the MEM/ESC button to enter a new memory
location or edit an already programmed memory
location.
Memory Scan continued
Scan Button
a. Press the MEM/ESC button to enter the channel/privacy code in the
selected memory location. Radio then proceeds to next memory
location, which will blink.
2. Press the Channel Up or Channel Down button to
select the memory location (0 through 9).
5. Press the MEM/ESC button. The channel numbers
will flash on the display.
To set VOX sensitivity:
1. Press the Mode/Power button until the VOX icon
flashes and the current sensitivity level is displayed.
Roger Beep Confirmation Tone
9. Choose one of the following:
If a location has been programmed before,
its associated channel/privacy code will be
shown on the display.
2. Press the Channel Up or Channel Down
button to turn VOX On or Off.
3. Choose one of the following:
a. Press the Mode/Power button to enter the
new setting and proceed to other functions.
b. Press the Talk or Call/Lock button to enter the
new setting and return to Standby mode.
c. Do not press any buttons for 15 seconds to enter
the new setting and return to Standby mode.
VOX Sensitivity Level
To program a memory location:
If “oF” flashes in place of the privacy code numbers, a privacy
code is already set in the opposite (CTCSS or DCS) system.
Press the Channel Up or Channel Down button to cancel the
opposite code and select a privacy code from the active
system for the selected channel.
Ten Call Tone Settings
Channel Button
2. Press either Channel Up or Channel Down to
begin scanning memory channels.
The Scan Mem will continue to be displayed when
scan is on. Your radio will continue to scan all
memory channels and stop if an incoming
transmission is detected. Your radio will remain on
the channel for 10 seconds.
14
13
Warranty & Trademark Acknowledgment
Limited One-Year Warranty
Altis Global Limited warrants to the original consumer purchaser only that this product and
the component parts thereof, will be free from defects in workmanship and materials for a
period of one year from the date of first consumer purchase. During this period, Altis will,
repair or replace, at its sole option and discretion, this product or any defective parts. Altis’
liability hereunder shall be limited to repair or replacement of the defective part or parts,
and such correction shall constitute a fulfillment of all of Altis’ warranties hereunder.
This limited warranty is only valid for the original consumer purchaser in limited jurisdictions
and is not transferrable. This limited warranty will automatically terminate prior to expiration
if this product is sold or otherwise transferred to another party. The product must be
purchased from Altis or an authorized dealer or the warranty is void. This limited warranty is
valid only for products purchased and utilized in specific jurisdictions. Please visit our
website at www.cobrawalkietalkie.com for a list of jurisdictions wherein this limited
warranty is valid.
This limited warranty does not cover damage due to misuse, abuse, negligence, acts of
God, accident, commercial use or modification of, or to any part of this product. This
warranty does not cover damage due to improper operation, maintenance or installation;
ordinary wear and tear; or attempted alterations or repairs by anyone other than Altis or
someone authorized by Altis to do warranty work. Any unauthorized alterations or repairs
will void this warranty. This limited warranty does not cover product sold AS IS or WITH ALL
FAULTS. This limited warranty is invalid if the factory applied serial number or date stamp
has been altered, defaced or removed from this product. This limited warranty does not
cover product purchased or utilized in a jurisdiction not covered.
The procedure for obtaining service and support, and the applicability of this warranty, will
vary depending on the country or jurisdiction in which you purchase and utilize the product.
For details on obtaining product service, support and other warranty information please visit
www.cobrawalkietalkie.com.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state and country to country.
ALTIS IS NOT LIABLE FOR ANY CLAIM MADE BY A THIRD PARTY OR MADE BY YOU FOR A
THIRD PARTY. THIS LIMITATION APPLIES WHETHER DAMAGES ARE SOUGHT, OR A CLAIM
MADE, UNDER THIS WARRANTY OR AS A TORT CLAIM (INCLUDING NEGLIGENCE OR STRICT
PRODUCT LIABILITY), A CONTRACT CLAIM, OR ANY OTHER CLAIM. THIS LIMITATION
CANNOT BE WAIVED OR AMENDED BY ANY PERSON. THIS LIMITATION OF LIABILITY WILL
BE EFFECTIVE EVEN IF ALTIS OR AN AUTHORIZED REPRESENTATIVE OF ALTIS HAS BEEN
ADVISED BY YOU OF THE POSSIBILITY OF ANY SUCH DAMAGES.
Some states and countries do not allow limitations on how long an implied warranty lasts
and do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitations may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state and country to country.
Provided that the product was purchased from Altis itself or through its authorized reseller
or agent and utilized in the U.S.A., Altis will, without charge, repair or replace, at its option,
defective products, products or component parts upon delivery to the authorized Altis Global
Limited Authorized Service Center, accompanied by proof of the date of first customer
purchase, such as a duplicated copy of a sales receipt.
You must pay any initial shipping charges required to ship the product for warranty service,
but the return charges, to an address in the U.S.A, will be at Altis’ expense, if the product is
under warranty.
For Products Purchased Outside the U.S.A.
Please contact your authorized local reseller or agent for warranty information.
Trademark Acknowledgment
Manufactured, distributed, or sold by Altis Global Limited, official licensee for this product.
Cobra®, microTalk®, Nothing Comes Close to a Cobra®, and the snake design are registered
trademarks of Cobra Electronics Corporation, USA. Cobra Electronics Corporation™ is a
trademark of Cobra Electronics Corporation, USA. All other product or service names are the
property of their respective owners.
©Cobra Electronics Corporation, USA 2018. All rights reserved.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, ALTIS MAKES NO OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. ALTIS EXPRESSLY
DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED
WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS
EXPRESSED WARRANTY.
LIMITATION OF REMEDIES AND DAMAGES. REPAIR OR REPLACEMENT AS PROVIDED
UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. ALTIS SHALL
NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT
LIMITED TO ATTORNEYS’ FEES AND/OR COSTS OF LITIGATION, FOR BREACH OF ANY
EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. ALTIS IS NOT LIABLE FOR ANY
DAMAGES CAUSED BY THE PRODUCT OR BY THE PRODUCT TO PERFORM, INCLUDING ANY
LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGES, OR CONSEQUENTIAL DAMAGES.
19
20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising