Brinkmann | BA6220 | Operating Instruction | Brinkmann BA6220 FH2, Pressure Boosting Pumps Operating Instruction

Brinkmann BA6220 FH2, Pressure Boosting Pumps Operating Instruction
BA6220
Operating Instructions
BRINKMANN Pressure Boosting Pumps
FH2…FH6
BRINKMANN PUMPS, Inc.
47060 Cartier Drive
Wixom, MI 48393
USA
Phone: +1 248 926 9400
Fax.: +1 248 926 9405
www.brinkmannpumps.com
sales@brinkmannpumps.com
Subject to change without prior notice.
Order - No.: BA6220 ENGLISH
 Brinkmann Pumps, Inc.
Edition 02/2018
Page 1 of 13
Brinkmann Pressure Boosting Pumps series FH2 ... FH6
Contents
1
2
3
4
5
6
7
Indication to the manual .................................... 2
Description of the Product .............................. 2-5
Safety instructions ............................................. 6
Transportation and Storage ............................... 6
Installation and Connection ............................ 7- 8
Start-up / Shut-down ......................................... 8
Operation........................................................... 8
8
9
10
11
12
13
1 Indication to the manual
This operating manual gives basic instructions which
are to be observed during installation, operation and
maintenance of the pump. It is therefore imperative
that this manual be read by the responsible personnel
and operator prior to assembly and commissioning. It
is always to be kept available at the installation site.
1.1
Identification of safety instructions in the
operating manual
Safety instructions given in this manual noncompliance with which would affect safety are identified by the following symbol
Safety sign according with ISO 3864 – B.3.1
or where electrical safety is involved, with:
Safety sign according with ISO 3864 – B.3.6
Where non-compliance with the safety instructions
may cause a risk to the machine and it’s function the
word
ATTENTION
is inserted.
2 Description of the Product
2.1 General description of the pump
Pumps of this type are multi-stage rotary pumps.
Series FH use closed impellers in order to minimizing
power consumption and to optimize hydraulic pump
efficiencies.
The pump shaft and the motor shaft are connected by
a coupling. The pump shaft is sealed by a rotating
mechanical seal.
These Pumps are not self-priming.
Pump and motor form a compact and space-saving
unit.
The pumps can be mounted next to the coolant tank
or the lined-up pump.
Servicing and Maintenance ............................... 8
Troubleshooting Guide ...................................... 9
Spare Parts................................................. 10-11
Repair .............................................................. 11
Disposal ........................................................... 11
Terms and Conditions ................................ 12-13
2.2 Intended use
In combination with pre-pumps or central coolant
supply pumps of series FH work as pressure booster
up to 26 bar increase within the limiting application in
accordance with table 1.
Limit of Application (Table 1)
Type
Mediums
FH2…6
Industry water, coolant, cooling- and
cutting-oils
Kinetic viscosity …115 SSU (...25 mm2/s)
of the medium
Temperature of 30 … 175 °F (0 ... 80 °C)
medium
max. inlet
375 PSI (26 bar)
pressure
max. operation 775 PSI (54 bar)
pressure
Particle-size in 0.04 Inches (1 mm)
the medium
min. delivery
1% of Q max.
volume
Dry running
The pumps are not suitable for dry
running.
Motor cycle
Motors less 4.0
HP max. 200
time per hour
from 4.0 HP to 5.4 HP max. 40
from 6.7 HP to 14 HP max. 20
Ambient
104 °F (40 °C)
temperature
Set-up altitude 3280 ft (1000 m)
ATTENTION
The pumps are to be operated within their design
limits. Applications outside of these limits are not
approved. The manufacturer is not responsible for any
damages resulting from use of the pumps in such
applications.
2.3
Type Designation
FH2 11 S 39
Length
60 Hz
BA6220
Edition 02/2018
Page 2 of 13
2.4
Technical data
Type
Max. del.
pressure
spec. weight 1
PSI
bar
Max. del.
volume
Height
Length
l
GPM
l/min
H
Inches mm
Weight
Inches mm
Power
lbs
kg
HP
kW
Noise
level 1)
60 Hz
dBA
FH203S19
FH204S19
38
50
2.4
3.4
10.5
40
19.2
488
7.8
197
37.3
37.5
16.9
17.0
0.6
0.45
61
FH205S19
62
4.1
11.2
42
19.2
488
7.8
197
38.4
17.4
0.73
0.54
61
FH206S29
77
5.1
23.1
588
11.7
297
39.5
17.9
FH207S29
FH208S29
FH209S29
88
100
110
6.0
7.0
7.8
11.5
45
24.8
629
11.7
297
48.5
48.7
49.0
22.0
22.1
22.2
1.15
FH210S29
125
8.8
11.5
45
24.8
629
11.7
297
51.4
23.3
1.3
0.98
61
FH211S39
FH212S39
FH213S39
138
152
162
9.6
10.2
11.2
12
48
28.7
729
15.6
397
52.9
53.1
53.4
24.0
24.1
24.2
1.4
1.06
61
FH214S39
FH215S39
173
184
12.0
12.8
12
48
29.8
756
15.6
397
56.0
56.2
25.4
25.5
1.7
1.27
61
FH216S49
198
13.8
13
50
34.6
878
19.6
497
68.4
31.0
2.0
1.49
66
FH217S49
FH218S49
FH219S49
210
224
238
14.5
15.5
16.4
13
50
34.6
878
19.6
497
73.2
73.4
73.6
33.2
33.3
33.4
2.3
1.75
66
FH220S49
254
17.2
13.5
52
35.6
904
19.6
497
78.3
35.5
2.6
1.95
66
FH221S59
260
18.0
39.5
1004
23.5
597
80.5
36.5
FH222S59
FH223S59
273
288
19.0
19.9
14
55
40.8
1036
23.5
597
89.1
89.3
40.4
40.5
2.9
2.18
66
FH224S59
FH225S59
300
315
20.8
21.8
14
55
40.8
1036
23.5
597
90.8
91.3
41.2
41.4
3.4
2.55
66
FH226S69
FH227S69
328
340
22.5
23.2
44.7
1136 27.4
697
92.6
92.8
42.0
42.1
FH228S69
FH229S69
FH230S69
352
360
374
24.1
25.0
26.0
44.7
1136
697
95.0
95.5
95.9
43.1
43.3
43.5
3.9
2.94
66
14
55
27.4
0.86
61
1) Noise emissions measured in accordance with
DIN 45635 at a distance of 39.37 Inches (1 m)
The motor is surface-cooled and compliant with
DIN IEC 34 and EN 60034 (protection degree IP 55).
BA6220
Edition 02/2018
Page 3 of 13
Type
Max. del.
pressure
spec. weight 1
PSI
bar
Max. del.
volume
GPM
Height
l/min
Length
Weight
Power
l
H
Inches
mm
Inches
mm
lbs
kg
HP
kW
Noise
level 1)
60 Hz
dBA
FH403S19
46
3.2
23
84
19.2
488
7.8
197
39.5
17.9 0.73 0.54
61
FH404S19
FH405S19
60
78
4.2
5.3
23
84
20.8
529
7.8
197
44.5
44.8
20.2 1.15 0.86
20.3
61
FH406S29
92
6.2
24
88
24.8
629
11.7
297
46.7
21.2 1.4
1.06
61
FH407S29
FH408S29
106
120
7.6
8.3
24
88
25.8
656
11.7
297
49.4
49.6
22.4 1.7
22.5
1.27
61
FH409S29
137
9.5
25
92
26.7
678
11.7
297
66.2
30.0 2.0
1.49
66
FH410S29
156
11.8
25
92
26.7
678
11.7
297
66.6
30.2 2.3
1.75
66
FH411S39
172
10.6
25.5
95
31.7
804
15.6
397
71.4
32.4 2.6
1.95
66
FH412S39
186
12.8
72.8
33.0
FH413S39
200
13.9
25.5
FH414S39
FH415S39
218
236
15.0
16.0
FH416S49
FH417S49
FH418S49
250
264
280
FH419S49
FH420S49
95
32.9
836
15.6
397
83.8
38.0 2.9
2.18
66
26
100
32.9
836
15.6
397
84.9
85.1
38.5 3.4
38.6
2.55
66
17.1
18.1
19.2
26
100
36.9
936
19.6
497
86.0
86.2
86.4
39.0 3.9
39.1
39.2
2.94
66
297
316
20.2
21.8
27
105
36.6
929
19.6
497
112.2
112.5
50.9 5.1
51.0
3.8
75
FH421S59
FH422S59
328
342
22.5
23.8
40.5
1029
23.5
597
112.7 51.1
113.16 51.3
FH423S59
360
24.8
40.5
1029
23.5
597
122.4
4.55
75
27
105
55.5 6.1
1) Noise emissions measured in accordance with
DIN 45635 at a distance of 39.37 Inches (1 m)
The motor is surface-cooled and compliant with
DIN IEC 34 and EN 60034 (protection degree IP 55).
BA6220
Edition 02/2018
Page 4 of 13
Type
Max. del.
pressure
spec. weight 1
PSI
bar
Max. del.
volume
Height
Length
GPM
l/min
H
Inches mm
Weight
Power
1)
l
TH
Inches mm
lbs
kg
HP
kW
Noise
level 1)
60 Hz
dBA
FH603S19
48
3.2
45
170
20.8
529
7.8
197
43.9
19.9
1.15 0.86
61
FH604S19
62
4.2
45
170
20.8
529
7.8
197
46.3
21.0
1.4
1.06
61
FH605S24
77
5.2
45
170
23.9
606
9.7
247
48.5
22.0
1.7
1.27
61
FH606S24
91
6.2
46
175
24.7
628
9.7
247
61.7
28.0
2.3
1.75
66
FH607S29
107
7.8
46
175
27.7
704
11.7
297
70.6
32.0
2.6
1.95
66
FH608S29
122
8.4
48
185
29.0
736
11.7
297
77.2
35.0
2.9
2.18
66
FH609S34
139
9.8
48
185
30.9
786
13.7
347
83.8
38.0
3.4
2.55
66
FH610S34
158
10.8
50
195
30.9
786
13.7
347
86.0
39.0
3.9
2.94
66
FH611S39
171
12.0
32.9
836
15.6
397
87.3
39.6
FH612S39
184
13.0
50
195
32.6
829
15.6
397
115.3
52.3
4.6
3.45
75
FH613S49
FH614S49
202
220
14.0
15.2
50
195
36.6
929
19.6
497
117.3
118.0
53.2
53.5
5.1
3.8
75
FH615S49
FH616S49
238
250
16.2
17.8
52
200
36.6
929
19.6
497
4.55
75
1029
23.5
597
55.6
55.8
6.1
40.5
122.6
123.0
FH617S59
264
18.4
124.1
56.3
FH618S59
FH619S59
FH620S59
280
297
316
19.8
20.8
22.0
7.7
5.75
75
FH621S69
FH622S69
330
344
23.0
24.0
FH623S69
FH624S69
364
380
25.2
26.2
8.4
6.3
75
52
54
200
210
41.7
1059
23.5
597
133.0
133.2
133.4
60.3
60.4
60.5
45.6
1159
27.4
697
134.9
135.2
61.2
61.3
45.6
1159
27.4
697
142.2
142.7
64.5
64.7
1) Noise emissions measured in accordance with
DIN 45635 at a distance of 39.37 Inches (1 m)
The motor is surface-cooled and compliant with
DIN IEC 34 and EN 60034 (protection degree IP 55).
BA6220
Edition 02/2018
Page 5 of 13
3 Safety instructions
3.5
When operating the pump, the safety instructions
contained in this manual, the relevant national accident prevention regulations and any other service and
safety instructions issued by the plant operator are to
be observed.
 If hot or cold machine components involve hazards, they must be guarded against accidental
contact.
3.1
 Any leakage of hazardous (e.g. explosive, toxic,
hot) fluids (e.g. from the shaft seal) must be
drained away so as to prevent any risk to persons
or the environment. Statutory regulations are to be
complied with.
Hazards in the event of non-compliance with
the safety instructions
Non-compliance with the safety instructions may
produce a risk to the personnel as well as to the
environment and the machine and results in a loss of
any right to claim damages.
For example, non-compliance may involve the following hazards:
 Failure of important functions of the machines/plant
 Failure of specified procedures of maintenance
and repair
 Exposure of people to electrical, mechanical and
chemical hazards
 Endangering the environment due to hazardous
substances being released
3.2
 Guards for moving parts (e.g. coupling) must not
be removed from the machine while in operation.
 Hazards resulting from electricity are to be prevented (see for example, the VDE Specifications
and the bye-laws of the local power supply utilities).
 The pumps are only secured safely if properly
attached to the floor and to the lined-up pump or
tank.
 The female threads on the motor MUST NOT be
used to lift the entire pump and motor assembly.
3.6
Unauthorized modes of operation
 Pump may not be used in potentially explosive
environments!
 Pump and discharge piping are not designed to
hold any weight and may not be used as a step
ladder.
3.3
Safety instructions relevant for operation
Remaining Risk
Safety instructions relevant for maintenance,
inspection and assembly work
Any work on the machine shall only be performed
when it is at a standstill, it being imperative that the
procedure for shutting down the machine described in
this manual be followed.
Pumps and pump units which convey hazardous
media must be decontaminated.
On completion of work all safety and protective facilities must be re-installed and made operative again.
Prior to restarting the machine, the instructions listed
under “Start up” are to be observed.
3.7 Signs on the pump
It is imperative that signs affixed to the machine, e.g.:
 arrow indicating the direction of rotation
Risk of Injury!
Risk of squeezing or crushing body parts when installing or removing the pump exists. Proper and
secured lifting tools must be used.
Risk of burns!
The pump must have cooled down sufficiently prior to
commencing any repair, maintenance or installation.
3.4
Qualification and training of operating personnel
The personnel responsible for operation, maintenance, inspection and assembly must be adequately
qualified. Scope of responsibility and supervision of
the personnel must be exactly defined by the plant
operator. If the staff does not have the necessary
knowledge, they must be trained and instructed,
which may be performed by the machine manufacturer or supplier on behalf of the plant operator. Moreover, the plant operator is to make sure that the contents of the operating manual are fully understood by
the personnel.
BA6220
 symbols indicating fluid connections
be observed and kept legible.
3.8
Unauthorized alterations and production of
spare parts
Any modification may be made to the machine only
after consultation with the manufacturer. Using spare
parts and accessories authorized by the manufacturer
is in the interest of safety. Use of other parts may
exempt the manufacturer from any liability.
4 Transportation and Storage
Protect the pump against damage when transporting.
The pumps may only be transported in a horizontal
position and hooks or straps must be attached on the
motor and pump end.
Do not use the pump shaft for connecting any transportation aids such as hooks or straps.
Pumps must be drained prior to their storage.
Store pump in dry and protected areas and protect it
against penetration of foreign bodies.
Always store pump above the freezing point!
Edition 02/2018
Page 6 of 13
5.2
5 Installation and Connection
5.1 Mechanical installation
During any assembly or disassembly process the
pumps must be secured against tipping trough ropes
for example at all times.
Pumps must be mounted securely. Piping, tank and
pumps must be mounted without any tension.
The liquid entrance is situated at the pump body. The
pressure connection is at the connection cover in the
end of the pump unit (They are marked with arrows).
Possible leakage will be caught by a leakage chamber
and returned to the tank by means of a leakage line
from the leakage bore on the upper side of the flange.
To obtain the full flow rate it is recommended to
choose for the pipework the nominal bore diameter of
the pumps cross section for connection. Therefore
pipe bends should be used, not pipe angles!
The pipework must be qualified for occuring hydraulic
pressure.
All service work must be carried out by qualified
service personnel. Pump must be disconnected
from the power source and all rotating parts must
stand still. Reassure that pump is disconnected
from power source and cannot be switched on.
Verify that there is no voltage at the terminal
board!
According to the European Standard EN809 a motor
overload must be installed and properly set to the full
load amps stated on the pump name plate.
It is the responsibility of the machine operator to
decide whether or not an additional emergency switch
must be installed.
5.2.1
FH2...6
Electric wiring
Circuit
Tension voltage and frequency must correspond with
the shown specification on the nameplate.
The pump must be wired so that a solid longterm
electrical connection is ensured. Establish a solid
ground connection.
The electrical wiring must be performed according
to the wiring diagram shown inside the terminal
box cover. (Please see above sample wiring diagrams)
Wiring diagram e.g.
Voltage changing 1:2 YY / Y
e.g. 230 / 460 V, 60 Hz
YY
Low Voltage
Dimensions in Inches / mm
Y
High Voltage
ATTENTION
Pay attention of the max. tightening torque for
piping connection
Type
Pipe
connection
Cast iron
bronze
FH2...6
G1
66 ft. Lbs (90 Nm)
36 ft. Lbs (50 Nm)
When installed the space around the pump must
be large enough to provide sufficient cooling of
the motor.
The suction port cannot support the weight of the
supply pipe.
BA6220
Edition 02/2018
Page 7 of 13
Circuit on request
Y (Star connection)
7 Operation
up to 7.4 HP
(5.5 kW)
∆ (Delta connection)
8, 8.7, 10.1, 12.1, 14.7, 17.4 HP
(6, 6.5, 7.5, 9, 11, 13 kW)
Y 440 V – 480 V
60 Hz
∆ 440 V – 480 V
60 Hz
Liquid level
The valve on the suction side of the pump must be
opened 1 or 2 seconds before starting up the pump to
avoid the damage resulting from low pression.
Do not switch on pressure boosting pump FH before
positive inlet pressure by a primary pump or by a
static head pressure (from a central filtration system)
is established. Max. inlet pressure 375 PSI (26 bar).
CAUTION: avoid hydraulic shocks!
Care has to be taken that the pump station will not run
empty.
Voltage changing ∆ / Y.
e. g. 220 V – 240 V / 380 V – 420 V, 50 Hz
∆ (Delta Connection)
Y (Star Connection)
∆ 220 V – 240 V,
50 Hz
Y 380 V – 420 V,
50 Hz
There may be no foreign objects such as dirt, particles
or humidity inside the terminal board.
Mount terminal board cover to motor tight against dust
and humidity and close up all unused wiring ports.
Leakage hole
ATTENTION
When Variable Frequency Drives are used interfering
signals might occur.
Non-sinus shaped supply voltage from a variable
frequency drive might result in elevated motor temperatures.
6 Start-up / Shut-down
6.1
Start-up
ATTENTION
Switch off at the mains.
After connection the electrical wires, close the terminal box. Briefly start the motor (max. 30 sec.) and
check the rotation according to the arrow on the top of
the motor.
If the direction is incorrect change over two of the
power leads.
6.2 Shut-down
All service work must be carried out by qualified
service personnel. Pump must be disconnected from
the power source and all rotating parts must stand
still. Reassure that pump is disconnected from power
source and cannot be switched on. Verify that there is
no voltage at the terminal board!
Open terminal box and disconnect the power leads.
Empty out the pump.
BA6220
If the pump should lock up and cease, shut pump down
(see 6.2) and disconnect from power supply. Pump
must be uninstalled and removed from the system prior
to its repair.
8 Servicing and Maintenance
ATTENTION
The surface of the motor must be kept free of dirt.
The motor shaft is spinning in permanently greased
ball bearings (with special grease and increased
bearing play) and does not require any special
maintenance.
Edition 02/2018
Page 8 of 13
9 Troubleshooting Guide
Fault
Cause
Remedy
Motor does not start, no motor
noise
At least two of the power supply
leads have failed
Check fuses, terminals and supply
leads .
Overload has tripped
Inspect overload
One of the supply leads has failed
See above
Impeller faulty
Motor bearing faulty
Replace impeller
Replace bearing
Overload trips
Pump locked up mechanically
High on/of cycling frequency
Inspect pump hydraulics
Check application
Power consumption is too high
Wrong direction of rotation of
impeller
Lime or other deposits
mechanical friction
See above
High on/off cycling frequency
Wrong power supply (voltage or
cycles)
See above
Power supply must correspond with
name plate rating
Insufficient cooling
Check air flow at motor fan
Pump does not pump
Pre-pump does not work
Pump mechanism faulty
Pipe blocked
Check the pre-pump
replace pump mechanism
Clean pipe
Insufficient flow and pressure
Wrong direction of rotation of
impeller
Change over two power supply
leads
Pump mechanism silted up
Worn pump mechanism
Clean pump mechanism
Replace pump mechanism
Incorrect flow or pressure
Wrong power supply (voltage or
cycles)
Power supply must correspond with
name plate rating
Running noise/Vibration
Foreign objects in pump end
Impeller damaged
Bearing/Bushing broken
Remove foreign objects
Replace impeller
Replace bearing/bushing
Motor does not start, humming
noise
Motor overheats
BA6220
Edition 02/2018
Clean pump mechanism
repair pump
Page 9 of 13
10 Spare Parts
10.1 Spare part list for Pressure Boosting Pumps
Series FH2…FH6
Item
1
2
3
4
5
8
9
10
13
13
14
15
15
16
17
18
18
76
77
78
79
80
81
82
83
Parallel pin
Hexagon head cap screw
Hexagon socket head cap screw
Serrated lock washer
Hexagon nut
Hexagon cap nuts
Woodruff key
Distance plate instead
of impeller / 60 HZ
84 Hexagon socket pipe plug
BA6220
DIN
DIN
DIN
DIN
DIN
DIN
DIN
7
933
912
6798
934
917
6888
DIN 906
19
20
21
22
26
27
29
30
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
69
70
71
72
73
74
75
Edition 02/2018
Description
Stator with terminal board
Motor flange
End shield
Motor shaft with rotor
Terminal box
Fan
Fan cover
Gasket
Retaining ring
Retaining ring 2.0…3.9 HP
DIN 471
Thread rolling screw
DIN 7500
from 2.0 HP and over
Ball bearing
DIN 625
Ball bearing 2.0…3.9 HP
DIN 628
Ball bearing
DIN 625
Slotted cheese head screw
DIN 84
Stud bolt with bond up to 1.7 HP
Hexagon socket head cap screw DIN 912
From 2.0 HP and over
Parallel pin
DIN 7
Retaining ring
DIN 472
Retaining ring
DIN 471
Socket head cap screw
DIN 912
Compensation disk
O-ring from 2.0 HP and over
Rotary shaft seal from 1.15 HP and over
Rotary shaft seal from 1.15 HP and over
Pump body
Connection cover
Pump shaft
Diffusor with sliding ring
Entering stage with sliding ring
Outflow stage
Bearing stage with sliding ring
Impeller
Spacer-long 2 x per stage
Spacer-short 1 x per bearing stage
Sliding ring
Shaft sleeve
Supporting ring
Spiral backup ring
Mech. Seal stop ring cover
Mech. seal stop half-ring
Mech. seal stop ring
Pump casing
Clamp coupling
Coupling shield with M5 screw
Stud bolt
O-ring
Rotary shaft seal
Mechanical seal
Retaining ring
Page 10 of 13
10.2 Indications to the spare part order
Spare parts are available from the supplier.
Standard commercially available parts are to be
purchased in accordance with the model type.
The ordering of spare parts should contain the following details:
1. Pumptype
e.g. FH204S19
2. Pump No.
e.g. 02186220
The date of the construction year is a component
of the pumps type number.
3. Voltage, Frequency and Power
Take item 1, 2 and 3 from the nameplate
4. Spare part with item No.
e.g. Impeller item No. 57
cides with the key groove of the coupling clamp
(69.1). Press the pump shaft (52) toward the motor
and tighten the screws.
The distance between the two shaft ends must be
zero.
9) Lubricate the O-ring seal (72)
Put on the spiral-backup ring (63), the O-ring seal
(72), the connection cover (51) and the pump casing (67) and screw evenly the stud bolt (71) and
the hexagon cap nuts (81).
During the assembly from (63) and (72) take care
of the order. See the pump drawing.
10) Fit the coupling shield (70) into the pump body
(50) and tighten the M5 screws.
11) Reconnect pump to the power supply.
Note torques for the screw connections!
When putting the pump back into use, make sure the
direction of rotation is correct!
11 Repair
11.1 Exchange the rotary mechanical seal:
FH2…FH6
Tightening torques for screwed connections
1) Disconnect the pump from the power supply.
2) Loosen the M5 screws and pull out coupling shield
(70). Remove clamp coupling (69.1, 69.2) and parallel pin (76).
3) Loosen and pull off the hexagon cap nuts (81), the
stud bolt (71), connection cover (51) and the pump
casing (67) from the pump unit. Remove pump unit
with pump shaft (52) from the pump body (50).
Thread -  M4
4.8
Strength
classes
Tightening 0.7
(1)
torque
ft. lbs. (Nm)
M5
4.8
M6
8.8
M8
8.8
M10
8.8
2.2
(3)
3.3 (4.5)
15 (20)
11 (15)
22 (30)
22 (30)
Clamp
coupling
Clamp
coupling
4) Take off rotating axial face seal unit (74.1-74.5)
and mech. seal stop ring (66) from the shaft (52)
and clean the shaft. Pay attention to the drilled
hole for the parallel pin (76) that it is without any
bur. Check the sliding surface for the rotary shaft
seal (73) for any damage.
5) Remove complete seal (74.6. 74.7) from the pump
body (50) and clean the seat.
6) Mounting of the new axial face seal :
Ensure that the sliding surfaces of the ring and the
rotating axial face seal unit are free from grease
and dirt.
Moisten the angle-sleeve (74.7) of the counter ring
lightly with rinse water / (water with washing-up liquid) and push the unit into the seat of the pump
body (50).
Slide the mech. seal stop ring (66) first and then
the axial face seal (74.5-74.1) (single part) onto
the pump shaft (52).
7) Lubricate lightly the lip of the rotary shaft seal (73)
and push it into the pump body (50). Then insert
the pump shaft (52) with the pump unit through the
rotary shaft seal (73).
12 Disposal
8) Fit together the coupling clamp (69) with the parallel pin (76) around the shafts, tighten the hexagon
socket head cap screws (78) with the serrated lock
washer (79) lightly.
Be sure that the key of the motor shaft (4) coin-
When disposing of the pump or the packaging materials the local and national regulation for proper disposal must be complied with.
Prior to its disposal, the pump must be completely
drained and decontaminated if necessary.
BA6220
Edition 02/2018
Page 11 of 13
13 Brinkmann Pumps Inc.
Terms and Conditions
The following terms and conditions
govern all quotations made by
Brinkmann Pumps Inc. („Brinkmann“)
and any orders based upon these
quotations. No contract term or condition
shall be amended, deleted or added
without the express written consent of
Brinkmann, and Brinkmann hereby
rejects any terms set forth in any other
writing which are in addition to or different from the terms in this quotation.
These items and conditions and any
other terms and conditions delivered in
writing by an authorized agent of
Brinkmann contemporaneously herewith
constitute the complete agreement
between Brinkmann and the buyer and
supersede all prior oral, written or printed
statements of any kind (including any
terms and conditions submitted by the
buyer and performance or production
data from any source whatsoever,
including references to accuracy,
capacity, and capability of products, all
of which are estimates only) made by
Brinkmann or the buyer or their respective representatives. No statement,
recommendation or assistance given by
Brinkmann or its representatives to
buyer or its representatives, in connection with the use of any products by
buyer, shall constitute a waiver by
Brinkmann of any of the provisions
hereof or affect Brinkmann‘s liability, as
defined herein. All transactions covered
hereby and all terms and conditions of
sale shall be governed by the laws of the
state of Michigan.
Prices
The products offered in this proposal and
the prices quoted are based on our
understanding of buyer‘s requirements;
any change in requirements will necessitate a revision in prices quoted. Prices
are F.O.B. our dock, Wixom, Michigan,
or other location as specified on proposal. Brinkmann‘s prices do not include
sales, use, excise, or similar tax, applicable to the sale or use of the equipment
proposed. These taxes shall be paid by
the buyer, or in lieu thereof, the buyer
shall provide Brinkmann with a tax
exemption certificate acceptable to the
taxing authorities.
Delays or failure to deliver
Brinkmann shall not be responsible for
delay or failure to deliver due to acts of
God, or to government action (civil or
military), or to prior orders, or to fire,
embargo, strike or other labor problems,
wrecks, delays in transportation, unusually severe weather or inability to obtain
necessary labor or materials from the
usual source of supply, or any other
circumstances beyond Brinkmann‘s
control.
BA6220
Brinkmann shall have the right to furnish
suitable substitutes for materials which
cannot be obtained because of such
force majeure.
Installation
Buyer shall install at its own expense, all
products covered hereby in accordance
with the operating instructions to be
furnished to buyer upon request. Unless
otherwise stated, no installation services
are included in the price indicated.
Limited warranty
Brinkmann warrants to the buyer (but not
to any others) for a period of one year
from date of shipment that all new parts
are free from defects in material and
workmanship.
Brinkmann‘s said warranty shall exist
only if buyer gives written notice to
Brinkmann within ten days after the first
determination that the part is defective
and within the aforesaid one year period
from the date of shipment and includes
in said notice consent to Brinkmann to
inspect, at any reasonable time, said
part and the machine in which it may be
embodied, and if, and only if, Brinkmann
determines to its reasonable satisfaction
upon said inspection that said part and
the machine in which it may be embodied are, and have been, used in accordance with all Brinkmann‘s instructions as
to maintenance and operation set forth in
the operating instructions relating to the
machine. Brinkmann‘s warranty is limited
to shipping to buyer replacement of any
part which is so proven to be defective
and in any event shall have no liability
whatsoever for incidental or consequential damage or loss of profit,
including damages resulting from
personal injury or death, or damage to,
or loss of use of, any property.
Brinkmann is not responsible for shipping costs or labor, extends no warranty
of any kind for gasket, seals and wear
and tear materials. Notwithstanding any
provisions of these terms and conditions,
this warranty is the only warranty
extended by Brinkmann in connection
with any sales of products and is in
lieu of all other warranties, express or
implied, including warranties of
merchantability or fitness for purpose. No agent, employee or representative of Brinkmann has any authority
to bind Brinkmann to any affirmation,
representation, or warranty concerning
the products that are the subject of this
quotation beyond that specifically
included in the written quotation.
Brinkmann shall have no obligation to
install or provide improvements or
changes in design adapted by
Brinkmann for similar equipment subsequent to acceptance of buyer‘s order.
Edition 02/2018
Warranties have been discussed and
understood by both parties.
Buyer‘s use and O.S.H.A.
Buyer shall use and require all persons
operating the equipment to use all
proper and safe operating procedures
set forth in operating instructions relating
to the equipment and observe all occupational safety health and standards act
(O.S.H.A.), American National Standard
Institute (ANSI), and state regulations as
required and all available, feasible and
practical point of operation safety
devices consistent with buyer‘s use of
the equipment. Buyer shall not remove
or modify, any device, warning sign,
operating instructions or work handling
tools installed on or attached to the
equipment. Buyer shall notify Brinkmann
promptly, in writing, and in all events
within ten (10) days after its occurrence,
of any accident or malfunction involving
any equipment which results in injury to
or death of persons or damage to
property, or the loss of use thereof and
buyer shall cooperate fully with
Brinkmann in investigation and determining the cause of any such occurrence of
malfunction. At Brinkmann‘s request
made at any time, buyer will either at its
or Brinkmann‘s place of business, permit
to redesign, remodel or revise the
equipment and buyer waives any claims
against Brinkmann for buyer‘s inability to
use the equipment during the time that
same is out of service for such revision,
modification or redesign.
Brinkmann shall not be responsible for
any failure to comply which results from
the location, operation, design, use or
maintenance of the equipment from
alternation of the equipment by persons
or firms other than Brinkmann, or from
an option or accessory to the equipment
by persons or firms other than
Brinkmann, which was available to the
buyer but omitted at the buyer‘s direction, or from design or instructions
furnished by the buyer or its agents. In
view of the above, Brinkmann does not
make any warranties with respect to
O.S.H.A. requirements, including noise;
and will not be responsible for fines,
penalties, or consequential damages.
Payment terms
Net payment in full of all invoices is due
thirty (30) days net, unless stated
otherwise in quotation. Any unpaid
balance thereafter shall be subject to a
service charge of 1.75 % per month or, if
illegal, at the highest rate allowed by law.
There shall be no extension or change in
the time for payment due to delay in
installation and/or delays in operation of
the equipment caused by damage,
warranty service or warranty replace-
Page 12 of 13
ment of parts. If after Brinkmann‘s
acceptance of buyer‘s purchase order,
buyer requests Brinkmann to delay
shipment of the equipment, the purchase
price shall become due and owing thirty
(30) days after the equipment is ready
for shipment.
If buyer fails to pay the purchase price
as provided herein and Brinkmann
institutes a lawsuit for the collection of
said price, buyer agrees to pay
Brinkmann‘s reasonable attorney fees
incurred in connection therewith.
Acceptance of orders
Quotations are offered for written
acceptance within thirty (30) days from
date (unless otherwise stated) but are
subject to change without notice at any
time before acceptance. If any order
contains printed, stamped or other
provisions inconsistent or in conflict with
the terms and conditions hereof, the
terms and conditions hereof shall
control, unless otherwise specifically
stated by Brinkmann in writing. All
clerical errors are subject to correction in
favor of either party upon notice of either
party. All orders are subject to the credit
approval of Brinkmann. An order containing subject matter not within the
contemplation of the proposal shall be
subject to a further quotation as to price
or delivery or both. Modifications,
changes, deferred shipments, cancellations or additions will be effective only if
accepted by Brinkmann in writing and
then only upon terms that will indemnify
Brinkmann against all costs and losses.
Title and security agreement
Delivery to carrier shall constitute
transfer to the buyer, and all risk of loss
or damage in transit shall be borne by
the buyer.
By execution of a purchase order, buyer
hereby grants to Brinkmann a security
interest in the equipment covered by the
proposal, and its products and/or proceeds in order to secure the payment of
the purchase price thereof and buyer
authorizes to file financing statements
reflecting this security interest without
buyer‘s signature. Buyer will cooperate
with Brinkmann in preparing documents
necessary to perfect this security interest.
Proprietary and other materials
This quotation and all drawings, specifications, materials, patterns, and special
purpose manufacturing aids which are
supplied to buyer by Brinkmann shall be
kept in confidence and shall be listed
and maintained in suitable condition at
the expense of buyer and are to be
considered the property of Brinkmann
held on consignment by buyer and to be
insured while in buyer‘s possession.
Such articles and all copies thereof from
any source shall be returned to
BA6220
Brinkmann at any time upon request and
shall not be used for or by any third
parties without the express written
permission of Brinkmann.
Performance in event of default
In addition to the rights and remedies
conferred upon Brinkmann by law,
Brinkmann will not be required to proceed with the performance of any order
or contract if buyer is in default in the
performance of any order or contract
with Brinkmann and in case of doubt as
to buyer‘s financial condition, shipments
under an order may be suspended or
sent sight draft with bill of lading attached and Brinkmann may decline
further shipments except for cash before
shipment.
Hold harmless/indemnity
Except to the extent of the limited
warranty set forth above and
Brinkmann‘s own gross negligence or
willful misconduct, buyer hereby:
(1) waives, releases and discharges any
and all claims of any and every kind
(including but not limited to injury or
death of any person or damage to
property), which it may have at any time
against Brinkmann, its agents or employees, by reason of or arising out of
any claimed improper design, specification or manufacture of the equipment
sold hereunder, or of any claimed
inadequate or insufficient safeguards or
safety devices; and (2) covenants to
indemnify and hold harmless Brinkmann,
its agents and employees of, from and
against any and all loss, damage,
expense (including attorney‘s fees),
claims, suits or liability which Brinkmann
or any of its employees may sustain or
incur at any time for or by reason of any
injury or death of any person or persons
or damage to any property, arising out of
any claimed improper design or manufacture of the equipment sold hereunder,
or of any claimed inadequate or insufficient safeguards or safety devices.
sole judgment of Brinkmann constitute
an improvement over former practice.
Production data, where given, are based
on Brinkmann‘s careful analysis and
understanding of the limits of accuracy,
machinability of materials, amount of
material to be removed, handling facilities provided, and location points but are
nonetheless an estimate only and not
guaranteed or warranted. In no event
shall Brinkmann be responsible for
performance figures supplied by other
parties. If by written agreement the
equipment is to be subject to acceptance
tests before shipment, rejection under
this clause must take place prior to
shipment.
Returned equipment
In no case is equipment to be returned
without first obtaining written permission
from Brinkmann. Unless otherwise
expressly agreed an order for equivalent
value must accompany returned equipment and all such returned equipment
will be accepted for credit only after
inspection. Equipment returned without
good cause and for which no credit is
given shall be subject to a restocking
charge. Buyer returning equipment must
pay transportation charges and bear
risks of loss or damage to goods while in
transit. Acceptance of returned products
by Brinkmann‘s receiving department
shall not bind Brinkmann nor have any
force or effect unless acceptance is
made by Brinkmann in writing.
Electrical equipment
Motors, electrical equipment and wiring
on the equipment quoted will be supplied
in accordance with the manufacturer‘s
standards. Unless specifically quoted
they are not guaranteed to meet ordinances of any local governing body and
the responsibility of conforming to any
local ordinance is assumed by the buyer.
Inspection and testing, production
estimates and performance
All working drawings or other materials
provided by Brinkmann are for general
information purposes only and may or
may not relate to buyer‘s order or other
equipment. Any specifications contained
therein are not binding on Brinkmann
except as expressly so stated.
Brinkmann reserves the right to make, at
any time, such changes in detail of
design or construction as shall in the
Edition 02/2018
Page 13 of 13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising