Brinkmann | BAS6530 | Operating Instruction | Brinkmann BAS6530 SAL1130, Quick Suctioning Immersion Pumps Operating Instruction

Brinkmann BAS6530 SAL1130, Quick Suctioning Immersion Pumps Operating Instruction
BAS6530
Operating Instructions
BRINKMANN Immersion Pumps
STA/SAL1130...2000, SGL1400…1700,
SFL1360…1860
BRINKMANN PUMPS, Inc.
47060 Cartier Drive
Wixom, MI 48393
USA
Phone: +1 248 926 9400
Fax.: +1 248 926 9405
www.brinkmannpumps.com
sales@brinkmannpumps.com
Subject to change without prior notice.
Order - No.: BAS6530 ENGLISH
 Brinkmann Pumps, Inc.
Edition 04/2019
Page 1 of 11
Brinkmann Immersions Pumps of the Series STA/SAL1130 ... 2000,
SGL1400 and SFL1360…1860
Contents
1
2
3
4
5
6
7
Indication to the manual .................................... 2
Description of the Product .............................. 2-3
Safety instructions ............................................. 4
Transportation and Storage ............................... 4
Installation and Connection ............................ 5-6
Start-up / Shut-down ......................................... 6
Operation........................................................... 6
8
9
10
11
12
13
1 Indication to the manual
This operating manual gives basic instructions which
are to be observed during installation, operation and
maintenance of the pump. It is therefore imperative
that this manual be read by the responsible personnel
and operator prior to assembly and commissioning. It
is always to be kept available at the installation site.
1.1
Identification of safety instructions in the
operating manual
Safety instructions given in this manual noncompliance with which would affect safety are identified by the following symbol
Safety sign according with ISO 3864 – B.3.1
or where electrical safety is involved, with:
Safety sign according with ISO 3864 – B.3.6
Where non-compliance with the safety instructions
may cause a risk to the machine and it’s function the
word
ATTENTION
is inserted.
2 Description of the Product
2.1 General description of the pump
Pumps of this type are one-stage rotary pumps where
the impellers are fixed on the driving shaft extension.
The pump shaft and motor shaft are interconnected
by means of a shaft clamp. Pump and motor form a
compact and space-saving unit. These pumps are
fitted out with semi-open impellers and a suction
screw SAL, SGL, SFL.
Vertically mounted pumps are equipped with a mounting flange. The pump end immerses into the tank and
the motor extends vertically above the tank.
Servicing and Maintenance ............................... 6
Troubleshooting Guide ...................................... 7
Spare Parts..................................................... 8-9
Repair ................................................................ 9
Disposal ............................................................. 9
Terms and Conditions ................................ 10-11
2.2 Intended use
The immersion pumps of the series STA/SAL, SGL
and SFL are suitable for handling contaminated
coolants within the limiting application in accordance
with table 1.
The pumps of SAL, SGL and SFL are suitable for
handling extremely inflated fluids (grinding oils SGL).
Limit of Application (Table 1)
Type
STA/SAL, SGL, SFL
Mediums
Coolant, cooling- and cutting-oils
grinding oils SGL
Chip material
Aluminium, steel, coloured steels
SFL
max. chip to coolant ratio by weight:
1.0%
Kinetic viscosity …200 SSU (...45 mm2/s)
of the medium
Temperature of 30 … 175 °F (0 ... 80 °C)
medium
Particle-size in 0.67 Inches (17 mm)
the medium
STA/SAL1130, 1600
0.75 Inches (19 mm) STA/SAL2000
0.55 Inches (14 mm) SGL1400
0.47 Inches (12 mm) SGL1700
0.55 Inches (14 mm)
SFL1360…1860
min. delivery
1% of Q max.
volume
Dry running
Dry running causes increased wear
and should be avoided.
During the test of the direction of
rotation (< 30 s) permissible.
Motor cycle
Motors from 6.7 HP to 12 HP max.
time per hour
20
from 13.4 HP to 29.5 HP max. 15
for
STA/SAL,SGL
SFL
The pump SFL should be operated
in continual operation mode, not
pulsed mode.
Ambient tempe- 104 °F (40 °C)
rature
Set-up altitude 3280 ft (1000 m)
ATTENTION
The pumps are to be operated within their design
limits. Applications outside of these limits are not
approved. The manufacturer is not responsible for any
damages resulting from use of the pumps in such
applications.
BAS6530
Edition 04/2019
Page 2 of 11
Technical data
Max. del.
pressure
spec. weight 1
PSI
bar
Max. del.
volume
GPM
l/min
Height
H
Inches
mm
Depth of
immersion
STA1) h
Inches mm
Weight
STA2)
g
lbs
kg
Power
HP
kW
Noise level
STA3)
dBA / 60
Hz
Type
Type
STA1130S 300
430
550
800
1050
SAL1130S 310
440
560
810
1060
72
5.0
570
2200
24.4
620
11.81 300
16.93 430
21.65 550
31.50 800
41.34 1050
324
329
344
381
388
147
149
156
173
176
16.9
12.6
80
STA1600S 300
430
550
800
1050
SAL1600S 310
440
560
810
1060
52
3.5
510
1900
24.1
612
11.81 300
16.93 430
21.65 550
31.50 800
41.34 1050
293
298
313
351
373
133
135
142
159
169
13.8
10.3
78
STA2000S 300
430
550
800
1050
SAL2000S 310
440
560
810
1060
66
4.6
590
2200
24.4
620
11.81 300
16.93 430
21.65 550
31.50 800
41.34 1050
346
351
366
404
410
157
159
166
183
186
16.9
12.6
79
SGL1400S 310
440
560
810
1060
58
4.0
500
1950
24.1
612
12.20 310
17.32 440
22.05 560
31.89 810
41.73 1060
295
300
315
353
375
134
136
143
160
170
13.8
10.3
SGL1700S 310
440
560
810
1060
74
5.0
550
2100
24.4
620
12.20 310
17.32 440
22.05 560
31.89 810
41.73 1060
348
353
368
406
419
158
160
167
184
190
20.1
15
SFL1550S 310 43
440
560
810
1060
2.9
450
1700
24.1
612
12.20 310
17.32 440
22.05 560
31.89 810
41.73 1060
280
291
298
340
359
127
132
135
154
163
11.5
8.6
SFL1850S 310
440
560
810
1060
57
3.9
540
2000
24.1
612
12.20 310
17.32 440
22.05 560
31.89 810
41.73 1060
295
304
313
355
373
134
138
142
161
169
13.8
10.3
SFL1360S 310
440
560
810
1060
48
3.3
450
1700
22.6
574
12.20 310
17.32 440
22.05 560
31.89 810
41.73 1060
258
267
282
318
337
117
121
128
144
153
10.0
7.48
SFL1860S 310
440
560
810
1060
6.4
4.4
550
2100
24.4
620
12.20 310
17.32 440
22.05 560
31.89 810
41.73 1060
320
326
331
370
379
145
148
150
168
172
16.9
12.6
1) Depth of immersion SAL = h + 0.4 Inches (10 mm)
2) Weight SAL = g + 4.4 lbs (2 kg)
3) Noise emissions measured in accordance with DIN 45635 at a distance of 39.37 Inches (1 m).
The motor is surface-cooled and compliant with
DIN IEC 34 and EN 60034 (protection degree IP 55).
BAS6530
Edition 04/2019
Page 3 of 11
3 Safety instructions
3.5
When operating the pump, the safety instructions
contained in this manual, the relevant national accident prevention regulations and any other service and
safety instructions issued by the plant operator are to
be observed.
• If hot or cold machine components involve hazards, they must be guarded against accidental
contact.
3.1
• Any leakage of hazardous (e.g. explosive, toxic,
hot) fluids (e.g. from the shaft seal) must be
drained away so as to prevent any risk to persons
or the environment. Statutory regulations are to be
complied with.
Hazards in the event of non-compliance with
the safety instructions
Non-compliance with the safety instructions may
produce a risk to the personnel as well as to the
environment and the machine and results in a loss of
any right to claim damages.
For example, non-compliance may involve the following hazards:
Safety instructions relevant for operation
• Guards for moving parts (e.g. coupling) must not
be removed from the machine while in operation.
ma-
• Hazards resulting from electricity are to be prevented (see for example, the VDE Specifications
and the bye-laws of the local power supply utilities).
• Failure of specified procedures of maintenance
and repair
• The pumps’ stability against falling over is not
ensured unless it is properly mounted onto the
tank.
• Failure of important
chines/plant
functions
of
the
• Exposure of people to electrical, mechanical and
chemical hazards
• Endangering the environment due to hazardous
substances being released
3.2
Unauthorized modes of operation
• Pump may not be used in potentially explosive
environments!
• Pump and discharge piping are not designed to
hold any weight and may not be used as a step
ladder.
3.3
Remaining Risk
• The female threads on the motor MUST NOT be
used to lift the entire pump and motor assembly.
3.6
Safety instructions relevant for maintenance,
inspection and assembly work
Any work on the machine shall only be performed
when it is at a standstill, it being imperative that the
procedure for shutting down the machine described in
this manual be followed.
Pumps and pump units which convey hazardous
media must be decontaminated.
On completion of work all safety and protective facilities must be re-installed and made operative again.
Prior to restarting the machine, the instructions listed
under “Start up” are to be observed.
3.7 Signs on the pump
It is imperative that signs affixed to the machine, e.g.:
• arrow indicating the direction of rotation
• symbols indicating fluid connections
be observed and kept legible.
Risk of Injury!
Risk of squeezing or crushing body parts when installing or removing the pump exists. Proper and
secured lifting tools must be used.
Risk of burns!
The pump must have cooled down sufficiently prior to
commencing any repair, maintenance or installation.
3.4
Qualification and training of operating personnel
The personnel responsible for operation, maintenance, inspection and assembly must be adequately
qualified. Scope of responsibility and supervision of
the personnel must be exactly defined by the plant
operator. If the staff does not have the necessary
knowledge, they must be trained and instructed,
which may be performed by the machine manufacturer or supplier on behalf of the plant operator. Moreover, the plant operator is to make sure that the contents of the operating manual are fully understood by
the personnel.
BAS6530
3.8
Unauthorized alterations and production of
spare parts
Any modification may be made to the machine only
after consultation with the manufacturer. Using spare
parts and accessories authorized by the manufacturer
is in the interest of safety. Use of other parts may
exempt the manufacturer from any liability.
4 Transportation and Storage
Protect the pump against damage when transporting.
The pumps may only be transported in a horizontal
position and hooks or straps must be attached on the
motor and pump end.
Do not use the pump shaft for connecting any transportation aids such as hooks or straps.
Pumps must be drained prior to their storage.
Store pump in dry and protected areas and protect it
against penetration of foreign bodies.
Always store pump above the freezing point!
Edition 04/2019
Page 4 of 11
5.2
5 Installation and Connection
5.1 Mechanical installation
During any assembly or disassembly process the pumps
must be secured against tipping trough ropes for example at all times.
Pumps must be mounted securely. Piping, tank and
pumps must be mounted without any tension.
The inlet is at the bottom of the immersed pump body.
The distance between the inlet and the tank bottom must
be so large that the inlet can not be blocked by deposits
during longer shutdowns.
To obtain the full flow rate it is recommended to choose
for the pipework the nominal bore diameter of the pumps
cross section for connection. Therefore pipe bends
should be used, not pipe angles!
The pipework must be qualified for occuring hydraulic
pressure.
Electric wiring
All service work must be carried out by qualified
service personnel. Pump must be disconnected
from the power source and all rotating parts must
stand still. Reassure that pump is disconnected
from power source and cannot be switched on.
Verify that there is no voltage at the terminal
board!
According to the European Standard EN809 a motor
overload must be installed and properly set to the full
load amps stated on the pump name plate.
It is the responsibility of the machine operator to
decide whether or not an additional emergency switch
must be installed.
5.2.1
Circuit
Tension voltage and frequency must correspond with
the shown specification on the nameplate.
The pump must be wired so that a solid longterm
electrical connection is ensured. Establish a solid
ground connection.
The electrical wiring must be performed according
to the wiring diagram shown inside the terminal
box cover. (Please see above sample wiring diagrams)
Wiring diagram e.g.
Up to 13.8 HP
Voltage changing 1:2 YY / Y
e.g. 230 / 460 V, 60 Hz
YY
Low Voltage
Y
High Voltage
Dimensions in Inches (mm)
*) Dimensions for STA/SAL2000, SGL1700, SFL1860
ATTENTION
Maximum tightening torque for piping connections is 150 ft. lbs. (200 Nm)!
When installed the space around the pump must
be large enough to provide sufficient cooling of
the motor.
Do not prop up the pressure line via the joining
socket.
16.9 Hp and higher
Delta connection
3 x 460 V, 60 Hz
The pump must be mounted in that way that
rotating parts under the cover of the coolant tank
can not be touched!
BAS6530
Edition 04/2019
Page 5 of 11
Circuit on request
7 Operation
up to 7.4 HP
(5.5 kW)
∆ (Delta connection)
8, 8.7, 10.1, 12.1, 14.7, 17.4 HP
(6, 6.5, 7.5, 9, 11, 13 kW)
Y 440 V – 480 V
60 Hz
∆ 440 V – 480 V
60 Hz
Y (Star connection)
Liquid level
According to the drawing shown below, the maximum
liquid level must stay about 1.18 Inches (30 mm)
below the mounting flange, also ensure that the
minimal liquid level for the STA pump is 3.15 Inches
(80 mm) before starting up the motor, for the SAL,
SGL and SFL pump the suction hole of the pump
body must be covered with liquid.
Voltage changing ∆ / Y.
e. g. 220 V – 240 V / 380 V – 420 V, 50 Hz
∆ (Delta Connection)
Y (Star Connection)
∆ 220 V – 240 V,
50 Hz
Y 380 V – 420 V,
50 Hz
There may be no foreign objects such as dirt, particles
or humidity inside the terminal board.
Mount terminal board cover to motor tight against dust
and humidity and close up all unused wiring ports.
SGL, SFL
Dimensions in Inches (mm)
ATTENTION
When Variable Frequency Drives are used interfering
signals might occur.
Non-sinus shaped supply voltage from a variable
frequency drive might result in elevated motor temperatures.
6 Start-up / Shut-down
6.1
Start-up
ATTENTION
The SFL pump should be operated in continual
operation mode, not pulsed mode!
Pulsed mode causes increased wear due to the
return flow of chips and additional load on the
bearings.
The pump should transport medium without chips
for 1-2 minutes before being switched off!
ATTENTION
Switch off at the mains.
After connection the electrical wires, close the terminal box. Briefly start the motor (max. 30 sec.) and
check the rotation according to the arrow on the top of
the motor.
If the direction is incorrect change over two of the
power leads.
6.2 Shut-down
All service work must be carried out by qualified
service personnel. Pump must be disconnected from
the power source and all rotating parts must stand
still. Reassure that pump is disconnected from power
source and cannot be switched on. Verify that there
is no voltage at the terminal board!
Open terminal box and disconnect the power leads.
Empty out the pump.
BAS6530
If the pump should lock up and cease, shut pump
down (see 6.2) and disconnect from power supply.
Pump must be uninstalled and removed from the
system prior to its repair.
8 Servicing and Maintenance
ATTENTION
The surface of the motor must be kept free of dirt.
The motor shaft is spinning in permanently greased
ball bearings (with special grease and increased
bearing play) and does not require any special
maintenance.
Edition 04/2019
Page 6 of 11
9 Troubleshooting Guide
Fault
Cause
Remedy
Motor does not start, no motor
noise
At least two of the power supply
leads have failed
Check fuses, terminals and supply
leads .
Overload has tripped
Inspect overload
One of the supply leads has failed
See above
Impeller faulty
Motor bearing faulty
Replace impeller
Replace bearing
Overload trips
Pump locked up mechanically
High on/of cycling frequency
Inspect pump hydraulics
Check application
Power consumption is too high
Wrong direction of rotation of
impeller
Lime or other deposits
mechanical friction
See above
High on/off cycling frequency
Wrong power supply (voltage or
cycles)
See above
Power supply must correspond with
name plate rating
Insufficient cooling
Check air flow at motor fan
Pump does not pump
liquid level too low
Pump mechanism faulty
Pipe blocked
Fill up liquid
replace pump mechanism
Clean pipe
Insufficient flow and pressure
Wrong direction of rotation of
impeller
Change over two power supply
leads
Pump mechanism silted up
Worn pump mechanism
Clean pump mechanism
Replace pump mechanism
Incorrect flow or pressure
Wrong power supply (voltage or
cycles)
Power supply must correspond with
name plate rating
Running noise/Vibration
Foreign objects in pump end
Impeller damaged
Bearing/Bushing broken
Remove foreign objects
Replace impeller
Replace bearing/bushing
Motor does not start, humming noise
Motor overheats
BAS6530
Edition 04/2019
Clean pump mechanism
repair pump
Page 7 of 11
10 Spare Parts
10.1 Spare Part List for the Immersion Pumps
of the Series STA/SAL1130 ... 2000
SGL1400…1700, SFL1360…1860
Item
1
2
3
5
6
7
8
9
9
10
11
12
13
14
15
16
17
18
19
20
21
23
25
26
27
28
29
30
50
51
52
52
54
55
57
58
61
63
64
65
68
69
70
74
76
77
78
91
92
93
Extension shaft up 21.7 Inches
(550 mm) depth of immersion
Insert shaft
Shaft clamp 2 x up 21.7 Inches
(550 mm) depth of immersion
BAS6530
79
81
82
83
84
85
86
87
88
Edition 04/2019
Description
Stator with terminal board
Motor flange
End shield
Terminal box frame
Terminal box cover
Fan
Fan cover
Ball bearing 10.0 HP
Ball bearing 11.5 HP
Ball bearing
Gasket
Gasket
Retaining ring
Thread rolling screw
Slotted cheese head screw
Socket head cap screw
Socket head cap screw
Nut from 16.9 HP and over
Parallel pin
Retaining ring 10.0 HP
Retaining ring 10.0 HP
Compensation disk
Bearing cover 11.5 HP and over
Socket head cap screw 11.5 HP
O-ring
Shaft nut 11.5 HP and over
Rotary shaft seal
Shaft seal from 11.5 HP and over
Pump body
Shaft with rotor
Inlet cover for STA
Intake cover for SAL, SGL and SFL
Pump plate
Impeller
Suction screw for SAL, SGL and SFL
Extension pump body up 21.7 Inches
(550 mm) depth of immersion
Bushing cartridge assembly
Distance plate
Woodruff key
Distance plate
Splash ring
Rotary shaft seal
Socket head cap screw with lock
Socket head cap screw with lock
Balancing ring (as needed)
Hexagon thin nut STA
Socket head cap screw up
21.7 Inches (550 mm) depth of immersion
Hexagon thin nut for SFL
Adapter
Joining socket
Socket head cap screw
Spring washer
O-ring
Screw plug
Sealing ring
Woodruff key SFL
DIN 625
DIN 628
DIN 625
DIN
DIN
DIN
DIN
DIN
DIN
DIN
DIN
7500
84
912
912
934
7
472
471
DIN 912
DIN 6888
DIN 912
DIN 912
DIN 439
DIN 912
DIN 912
DIN 7980
DIN 908
DIN 7603
Page 8 of 11
10.2 Indications to the spare part order
Spare parts are available from the supplier.
Standard commercially available parts are to be
purchased in accordance with the model type.
The ordering of spare parts should contain the following details:
1. Pumptype
e.g. SFL1550S440
2. Pump No.
e.g. 04196530
The date of the construction year is a component
of the pumps type number.
3. Voltage, Frequency and Power
Take item 1, 2 and 3 from the nameplate
4. Spare part with item No.
e.g. Intake cover item No. 52
11 Repair Instructions / Replacing shaft
clamps and shafts
3
1
2
1 = Shaft clamp
2 = Insert / extension shaft
3 = Motor shaft / Insert shaft
11.1 Dismantling the insert shaft or extension
shaft
– Disconnect the submergible pump from the mains
both electrically and mechanically.
– Remove pump from system. Secure pump against
tipping over, i.e. use ropes to secure pump.
– Set the pump down on the fan cover. Dismantle
the pump unit and the extension pump body (if appropriate).
Wear safety gloves!
Risk of injury due to sharp edges on pump components, i.e. impeller blades.
– Loosen the screws on the shaft clamp (1) one after
the other.
Do not, under any circumstances, remove the screws
completely, danger of injury!
– Remove the extension shaft (2) and shaft clamp
(1).
– Dismantle the pump body.
– Loosen the screws on the shaft clamp (1) (see
above), pull the insert shaft (2) off the motor shaft
(3).
BAS6530
11.2 Assembling the insert shaft and motor shaft
ATTENTION
Clean the contact surfaces of the insert shaft (2)
(inside) and the motor shaft (3). They must not be
lubricated or oiled.
– Set the motor down on the fan cover.
– Position the shaft clamp (1) (use a new shaft
clamp) in the centre of the cranked clamping diameter (2) of the insert shaft.
– Insert the motor shaft (3) into the insert shaft (2).
– Tighten:
Mark the first screw and tighten all the screws
evenly by hand, one after the other in a clockwise
direction (not cross-ways).
up to 16.9 HP
Use a torque screwdriver to tighten each screw first
with 1.5 ft. lbs. (2 Nm) then with 2.6 ft. lbs. (3.5
Nm) and finally with 3.7 ft. lbs. (5 Nm) (in a clockwise direction again).
Repeat the last turn with 3.7 ft. lbs. (5 Nm) 3 times.
> 16.9 HP
Use a torque screwdriver to tighten each screw first
with 1.5 ft. lbs. (2 Nm) then with 5.3 ft. lbs. (7 Nm)
and finally with 9 ft. lbs. (12 Nm) (in a clockwise direction again)
Mount the pump body.
In the case of pumps with an extension body, the
assembly and tightening of the second shaft clamp
is carried out as before.
The remainder of the reassembly process is to be
completed in the opposite order of the prior described
dismantling process.
ATTENTION
Note torques for the screw connections!
When putting the pump back into use, make sure the
direction of rotation is correct!
Tightening torques for screwed connections
Thread
-
Strength
classes
Tightening
torque
ft. lbs.
(Nm)
M5
M6
M8
M10
M12 M16
4.8
8.8
8.8
10.0
8.8
2.2
(3)
3.3
(4.5)
8 (11)
22 (30) 59
Item 16 Item.18 (80)
15 (20)
M16
8.8
44
(60)
Item.
83
44 (60)
Item. 79
SFL
74 (100)
Item. 77
STA
12 Disposal
When disposing of the pump or the packaging materials the local and national regulation for proper disposal must be complied with.
Prior to its disposal, the pump must be completely
drained and decontaminated if necessary.
Edition 04/2019
Page 9 of 11
13 Brinkmann Pumps Inc.
Terms and Conditions
The following terms and conditions govern
all quotations made by Brinkmann Pumps
Inc. („Brinkmann“) and any orders based
upon these quotations. No contract term or
condition shall be amended, deleted or
added without the express written consent
of Brinkmann, and Brinkmann hereby
rejects any terms set forth in any other
writing which are in addition to or different
from the terms in this quotation.
These items and conditions and any other
terms and conditions delivered in writing
by an authorized agent of Brinkmann
contemporaneously herewith constitute the
complete agreement between Brinkmann
and the buyer and supersede all prior oral,
written or printed statements of any kind
(including any terms and conditions
submitted by the buyer and performance
or production data from any source
whatsoever, including references to
accuracy, capacity, and capability of
products, all of which are estimates only)
made by Brinkmann or the buyer or their
respective representatives. No statement,
recommendation or assistance given by
Brinkmann or its representatives to buyer
or its representatives, in connection with
the use of any products by buyer, shall
constitute a waiver by Brinkmann of any of
the provisions hereof or affect Brinkmann‘s
liability, as defined herein. All transactions
covered hereby and all terms and conditions of sale shall be governed by the laws
of the state of Michigan.
Prices
The products offered in this proposal and
the prices quoted are based on our
understanding of buyer‘s requirements;
any change in requirements will necessitate a revision in prices quoted. Prices are
F.O.B. our dock, Wixom, Michigan, or
other location as specified on proposal.
Brinkmann‘s prices do not include sales,
use, excise, or similar tax, applicable to
the sale or use of the equipment proposed. These taxes shall be paid by the
buyer, or in lieu thereof, the buyer shall
provide Brinkmann with a tax exemption
certificate acceptable to the taxing authorities.
Delays or failure to deliver
Brinkmann shall not be responsible for
delay or failure to deliver due to acts of
God, or to government action (civil or
military), or to prior orders, or to fire,
embargo, strike or other labor problems,
wrecks, delays in transportation, unusually
severe weather or inability to obtain
necessary labor or materials from the
usual source of supply, or any other
circumstances beyond Brinkmann‘s
control.
BAS6530
Brinkmann shall have the right to furnish
suitable substitutes for materials which
cannot be obtained because of such force
majeure.
Installation
Buyer shall install at its own expense, all
products covered hereby in accordance
with the operating instructions to be
furnished to buyer upon request. Unless
otherwise stated, no installation services
are included in the price indicated.
Limited warranty
Brinkmann warrants to the buyer (but not
to any others) for a period of one year from
date of shipment that all new parts are free
from defects in material and workmanship.
Brinkmann‘s said warranty shall exist only
if buyer gives written notice to Brinkmann
within ten days after the first determination
that the part is defective and within the
aforesaid one year period from the date of
shipment and includes in said notice
consent to Brinkmann to inspect, at any
reasonable time, said part and the machine in which it may be embodied, and if,
and only if, Brinkmann determines to its
reasonable satisfaction upon said inspection that said part and the machine in
which it may be embodied are, and have
been, used in accordance with all Brinkmann‘s instructions as to maintenance and
operation set forth in the operating instructions relating to the machine. Brinkmann‘s
warranty is limited to shipping to buyer
replacement of any part which is so proven
to be defective and in any event shall have
no liability whatsoever for incidental or
consequential damage or loss of profit,
including damages resulting from personal
injury or death, or damage to, or loss of
use of, any property. Brinkmann is not
responsible for shipping costs or labor,
extends no warranty of any kind for
gasket, seals and wear and tear materials.
Notwithstanding any provisions of these
terms and conditions, this warranty is the
only warranty extended by Brinkmann
in connection with any sales of products and is in lieu of all other warranties, express or implied, including
warranties of merchantability or fitness
for purpose. No agent, employee or
representative of Brinkmann has any
authority to bind Brinkmann to any affirmation, representation, or warranty concerning the products that are the subject of this
quotation beyond that specifically included
in the written quotation. Brinkmann shall
have no obligation to install or provide
improvements or changes in design
adapted by Brinkmann for similar equipment subsequent to acceptance of buyer‘s
order.
Edition 04/2019
Warranties have been discussed and
understood by both parties.
Buyer‘s use and O.S.H.A.
Buyer shall use and require all persons
operating the equipment to use all proper
and safe operating procedures set forth in
operating instructions relating to the
equipment and observe all occupational
safety health and standards act
(O.S.H.A.), American National Standard
Institute (ANSI), and state regulations as
required and all available, feasible and
practical point of operation safety devices
consistent with buyer‘s use of the equipment. Buyer shall not remove or modify,
any device, warning sign, operating
instructions or work handling tools installed
on or attached to the equipment. Buyer
shall notify Brinkmann promptly, in writing,
and in all events within ten (10) days after
its occurrence, of any accident or malfunction involving any equipment which results
in injury to or death of persons or damage
to property, or the loss of use thereof and
buyer shall cooperate fully with Brinkmann
in investigation and determining the cause
of any such occurrence of malfunction. At
Brinkmann‘s request made at any time,
buyer will either at its or Brinkmann‘s place
of business, permit to redesign, remodel or
revise the equipment and buyer waives
any claims against Brinkmann for buyer‘s
inability to use the equipment during the
time that same is out of service for such
revision, modification or redesign.
Brinkmann shall not be responsible for any
failure to comply which results from the
location, operation, design, use or maintenance of the equipment from alternation of
the equipment by persons or firms other
than Brinkmann, or from an option or
accessory to the equipment by persons or
firms other than Brinkmann, which was
available to the buyer but omitted at the
buyer‘s direction, or from design or instructions furnished by the buyer or its agents.
In view of the above, Brinkmann does not
make any warranties with respect to
O.S.H.A. requirements, including noise;
and will not be responsible for fines,
penalties, or consequential damages.
Payment terms
Net payment in full of all invoices is due
thirty (30) days net, unless stated otherwise in quotation. Any unpaid balance
thereafter shall be subject to a service
charge of 1.75 % per month or, if illegal, at
the highest rate allowed by law. There
shall be no extension or change in the
time for payment due to delay in installation and/or delays in operation of the
equipment caused by damage, warranty
service or warranty replacement of parts. If
after Brinkmann‘s acceptance of buyer‘s
Page 10 of 11
purchase order, buyer requests Brinkmann
to delay shipment of the equipment, the
purchase price shall become due and
owing thirty (30) days after the equipment
is ready for shipment.
If buyer fails to pay the purchase price as
provided herein and Brinkmann institutes a
lawsuit for the collection of said price,
buyer agrees to pay Brinkmann‘s reasonable attorney fees incurred in connection
therewith.
Acceptance of orders
Quotations are offered for written acceptance within thirty (30) days from date
(unless otherwise stated) but are subject
to change without notice at any time
before acceptance. If any order contains
printed, stamped or other provisions
inconsistent or in conflict with the terms
and conditions hereof, the terms and
conditions hereof shall control, unless
otherwise specifically stated by Brinkmann
in writing. All clerical errors are subject to
correction in favor of either party upon
notice of either party. All orders are subject
to the credit approval of Brinkmann. An
order containing subject matter not within
the contemplation of the proposal shall be
subject to a further quotation as to price or
delivery or both. Modifications, changes,
deferred shipments, cancellations or
additions will be effective only if accepted
by Brinkmann in writing and then only
upon terms that will indemnify Brinkmann
against all costs and losses.
Title and security agreement
Delivery to carrier shall constitute transfer
to the buyer, and all risk of loss or damage
in transit shall be borne by the buyer.
By execution of a purchase order, buyer
hereby grants to Brinkmann a security
interest in the equipment covered by the
proposal, and its products and/or proceeds
in order to secure the payment of the
purchase price thereof and buyer authorizes to file financing statements reflecting
this security interest without buyer‘s
signature. Buyer will cooperate with
Brinkmann in preparing documents
necessary to perfect this security interest.
Proprietary and other materials
This quotation and all drawings, specifications, materials, patterns, and special
purpose manufacturing aids which are
supplied to buyer by Brinkmann shall be
kept in confidence and shall be listed and
maintained in suitable condition at the
expense of buyer and are to be considered the property of Brinkmann held on
consignment by buyer and to be insured
while in buyer‘s possession. Such articles
and all copies thereof from any source
shall be returned to Brinkmann at any time
upon request and shall not be used for or
by any third parties without the express
written permission of Brinkmann.
BAS6530
Performance in event of default
In addition to the rights and remedies
conferred upon Brinkmann by law, Brinkmann will not be required to proceed with
the performance of any order or contract if
buyer is in default in the performance of
any order or contract with Brinkmann and
in case of doubt as to buyer‘s financial
condition, shipments under an order may
be suspended or sent sight draft with bill of
lading attached and Brinkmann may
decline further shipments except for cash
before shipment.
Hold harmless/indemnity
Except to the extent of the limited warranty
set forth above and Brinkmann‘s own
gross negligence or willful misconduct,
buyer hereby:
(1) waives, releases and discharges any
and all claims of any and every kind
(including but not limited to injury or death
of any person or damage to property),
which it may have at any time against
Brinkmann, its agents or employees, by
reason of or arising out of any claimed
improper design, specification or manufacture of the equipment sold hereunder, or of
any claimed inadequate or insufficient
safeguards or safety devices; and (2)
covenants to indemnify and hold harmless
Brinkmann, its agents and employees of,
from and against any and all loss, damage, expense (including attorney‘s fees),
claims, suits or liability which Brinkmann or
any of its employees may sustain or incur
at any time for or by reason of any injury or
death of any person or persons or damage
to any property, arising out of any claimed
improper design or manufacture of the
equipment sold hereunder, or of any
claimed inadequate or insufficient safeguards or safety devices.
nonetheless an estimate only and not
guaranteed or warranted. In no event shall
Brinkmann be responsible for performance
figures supplied by other parties. If by
written agreement the equipment is to be
subject to acceptance tests before shipment, rejection under this clause must take
place prior to shipment.
Returned equipment
In no case is equipment to be returned
without first obtaining written permission
from Brinkmann. Unless otherwise expressly agreed an order for equivalent
value must accompany returned equipment and all such returned equipment will
be accepted for credit only after inspection. Equipment returned without good
cause and for which no credit is given shall
be subject to a restocking charge. Buyer
returning equipment must pay transportation charges and bear risks of loss or
damage to goods while in transit. Acceptance of returned products by Brinkmann‘s receiving department shall not bind
Brinkmann nor have any force or effect
unless acceptance is made by Brinkmann
in writing.
Electrical equipment
Motors, electrical equipment and wiring on
the equipment quoted will be supplied in
accordance with the manufacturer‘s
standards. Unless specifically quoted they
are not guaranteed to meet ordinances of
any local governing body and the responsibility of conforming to any local ordinance is assumed by the buyer.
Inspection and testing, production
estimates and performance
All working drawings or other materials
provided by Brinkmann are for general
information purposes only and may or may
not relate to buyer‘s order or other equipment. Any specifications contained therein
are not binding on Brinkmann except as
expressly so stated. Brinkmann reserves
the right to make, at any time, such
changes in detail of design or construction
as shall in the sole judgment of Brinkmann
constitute an improvement over former
practice. Production data, where given, are
based on Brinkmann‘s careful analysis and
understanding of the limits of accuracy,
machinability of materials, amount of
material to be removed, handling facilities
provided, and location points but are
Edition 04/2019
Page 11 of 11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising