Brinkmann | BAS6814 | Operating Instruction | Brinkmann BAS6814 SBA141S...143S, Horizontal End-Suction Pumps Operating Instruction

Brinkmann BAS6814 SBA141S...143S, Horizontal End-Suction Pumps Operating Instruction
BAS6814
Operating Instructions
BRINKMANN-Horizontal End Suction Pumps
SBA141S...143S, SBF125S
BRINKMANN PUMPS, Inc.
47060 Cartier Drive
Wixom, MI 48393
USA
Phone: +1 248 926 9400
Fax.: +1 248 926 9405
www.brinkmannpumps.com
sales@brinkmannpumps.com
Subject to change without prior notice.
Order - No.: BAS6814 ENGLISH
 Brinkmann Pumpen
Edition 02/2018
Page 1 of 12
Brinkmann–Horizontal End Suction Pumps Series SBA141S…143S, SBF125S
Contents
1
2
3
4
5
6
7
Indication to the manual ...................................... 2
Description of the Product ................................ 2-3
Safety instructions............................................ 3-4
Transportation and Storage ................................ 4
Installation and Connection .............................. 4-5
Start-up / Shut-down ........................................... 5
Operation ............................................................ 6
8
9
10
11
12
13
1 Indication to the manual
This operating manual gives basic instructions which
are to be observed during installation, operation and
maintenance of the pump. It is therefore imperative
that this manual be read by the responsible personnel and operator prior to assembly and commissioning. It is always to be kept available at the installation site.
1.1
Identification of safety instructions in the
operating manual
Safety instructions given in this manual noncompliance with which would affect safety are
identified by the following symbol
Servicing and Maintenance .............................. 6
Troubleshooting Guide ..................................... 7
Spare Parts ................................................... 8-9
Repair Instructions ..................................... 9-10
Disposal ......................................................... 10
Terms and Conditions ............................... 11-12
2.2 Intended use
These pumps are not self-priming and must be
gravity fed. They are designed to handle watersoluble coolants as well as cutting oils within the
limiting application in accordance with table 1.
Limit of Application (Table 1)
Type
SBA, SBF
Mediums
Coolants, cooling- and cuttingoils
2
…200 SSU (...45 mm /s)
Kinetic viscosity
of the medium
Temperature of
medium
30 … 175 °F (0 ... 80 °C)
Particle-size in
the medium
0.1 Inch SBA141S…143S
0.2 Inch SBF
min. delivery
volume
1% of Q max.
Dry running
Dry running causes increased
wear and should be avoided.
During the test of the direction of
rotation (< 30 s) permissible.
Switching-on
frequency per
hour
Motors less 4 HP
is inserted.
Ambient temperature
104 °F (40 °C)
2 Description of the Product
Set-up altitude
3280 ft (1000 m)
Safety sign according with ISO 3864–B.3.1
or where electrical safety is involved, with:
Safety sign according with ISO 3864–B.3.6
Where non-compliance with the safety instructions
may cause a risk to the machine and it’s function the
word
ATTENTION
2.1 General description of the pump
Pumps of this type are one or multi-stage centrifugal
inline pumps with a compact design where the
impellers are fixed on the driving shaft extension.
The pump shaft and motor shaft are interconnected
by means of a shaft clamp. These pumps are fitted
out with semi-open impellers and a suction screw in
order to minimize the risk of cavitations. All pumps
are equipped with a single mechanical seal.
These pumps are for horizontal installations next to
or underneath a tank. The pumps are foot mounted
and must be screwed down in order to ensure a
secure stance.
BAS6814
max. 200
ATTENTION
The pumps are to be operated within their design
limits. Applications outside of these limits are not
approved. The manufacturer is not responsible for
any damages resulting from use of the pumps in
such applications.
Edition 02/2018
Page 2 of 12
2.3
Technical data
Max. del.
Pressure
Max. del.
volume
Dimensions
spec. weight 1
Length
Weight
Power
HP
Noise
1)
level
dBA /
60 Hz
Type
PSI
bar
GPM
l/min
H
Inch
mm
h
Inch
mm
l
Inch
mm
Lbs
SBA141S
20
1.4
42
160
18.0
456
14.1
359
5.6
143
56
25.5 0.73
0.54 67
SBA142S
35
2.4
43
165
22.6
575
16.1
410
7.1
181
63
28.5 1.7
1.27 67
SBA143S
55
3.7
43
165
25.7
653
17.4
443
8.0
203
85
38.5 2.6
1.95 71
SBF125S
11
0.8
48
180
18.0
456
14.1
359
5.6
143
60
27.0 0.73
0.54 67
kg
kW
1) Noise emissions measured in accordance with DIN 45635 at a distance of 39.37 Inch (1 m).
Pipe connection: Suction Port DN50 / PN16, is equivalent to ASME B16.1-2005 class 25 Flange NPS 2
Discharge Port NPT1 ¼.
The motor is surface-cooled and compliant with DIN IEC 34 and EN 60034 (protection degree IP 55).
3 Safety instructions
When operating the pump, the safety instructions contained in this manual, the relevant national accident
prevention regulations and any other service and safety
instructions issued by the plant operator are to be
observed.
3.1
Hazards in the event of non-compliance with
the safety instructions
Non-compliance with the safety instructions may produce a risk to the personnel as well as to the environment and the machine and results in a loss of any right
to claim damages.
For example, non-compliance may involve the following
hazards:
 Failure of important functions of the machines/plant
 Failure of specified procedures of maintenance and
repair
 Exposure of people to electrical, mechanical and
chemical hazards
 Endangering the environment due to hazardous
substances being released
3.2
Unauthorized modes of operation

Pump may not be used in potentially explosive
environments!

Pump and pipes are not designed to hold any weight
and may not be used as a step ladder.
BAS6814
3.3
Remaining Risk
Risk of Injury!
Risk of squeezing or crushing body parts when installing
or removing the pump exists. Proper and secured lifting
tools must be used.
Risk of burns!
The pump must have cooled down sufficiently prior to
commencing any repair, maintenance or installation.
3.4
Qualification and training of operating personnel
The personnel responsible for operation, maintenance,
inspection and assembly must be adequately qualified.
Scope of responsibility and supervision of the personnel
must be exactly defined by the plant operator. If the staff
does not have the necessary knowledge, they must be
trained and instructed, which may be performed by the
machine manufacturer or supplier on behalf of the plant
operator. Moreover, the plant operator is to make sure
that the contents of the operating manual are fully
understood by the personnel.
Edition 02/2018
Page 3 of 12
3.5 Safety instructions relevant for operation
 If hot or cold machine components involve hazards,
they must be guarded against accidental contact.
 Guards for moving parts (e.g. coupling) must not be
removed from the machine while in operation.
 Any leakage of hazardous (e.g. explosive, toxic, hot)
fluids (e.g. from the shaft seal) must be drained away
so as to prevent any risk to persons or the environment. Statutory regulations are to be complied with.
 Hazards resulting from electricity are to be prevented
(see for example, the VDE Specifications and the
bye-laws of the local power supply utilities).
 The pumps are only secured safely if properly attached to the floor or underneath a tank.
 The female threads on the motor MUST NOT be
used to lift the entire pump and motor assembly.
In order to reach the maximum flow rate it is recommended that the pipe diameter is as close as possible to
the nominal pump connection diameter. Avoid the
introduction of pipe bends (no angled sections).
The installed pipes must be rated for the hydraulic
pressures which occur during operation. The positions
of the foot and pressure connection can be moved
around the circumference to 3 different positions. On the
S-type, the pipe connection can also be set to normal or
parallel alignment to the pump axis.
3.6
Safety instructions relevant for maintenance,
inspection and assembly work
Any work on the machine shall only be performed when
it is at a standstill, it being imperative that the procedure
for shutting down the machine described in this manual
be followed.
Pumps and pump units which convey hazardous media
must be decontaminated.
On completion of work all safety and protective facilities
must be re-installed and made operative again.
Prior to restarting the machine, the instructions listed
under “Start up” are to be observed.
3.7 Signs on the pump
It is imperative that signs affixed to the machine, e.g.:
 arrow indicating the direction of rotation
 symbols indicating fluid connections
be observed and kept legible.
3.8 Unauthorized alterations and production of
spare parts
Any modification may be made to the machine only after
consultation with the manufacturer. Using spare parts
and accessories authorized by the manufacturer is in
the interest of safety. Use of other parts may exempt the
manufacturer from any liability.
4 Transportation and Storage
Protect the pump against damage when transporting.
The pumps may only be transported in a horizontal
position and hooks or straps must be attached on the
motor and pump end.
Do not use the pump shaft for connecting any transportation aids such as hooks or straps.
Pumps must be drained prior to their storage.
Store pump in dry and protected areas and protect it
against penetration of foreign bodies.
Always store pump above the freezing point!
5 Installation and Connection
5.1 Mechanical installation
The pumps must be properly fastened. The pipework
must be installed so that no distortion of the pump can
occur. The fluid inlet is on the face side of the flangeconnected pump mechanism. The clearance between
the suction opening and the tank floor should be large
enough to prevent the suction opening from becoming
blocked even if the coolant is heavily polluted and the
pump has not been operated for long periods.
BAS6814
Dimensions in Inch (mm)
*) Dimensions for SBA143S
A suction screw is in the suction side of the pump,
risk of injury!
Touching the rotating parts is forbidden!
Reaching of the suction screw in the suction side of
the pump must be prevented by fitting preventive
measures!
ATTENTION
Maximum tightening torque for piping connections
is 90 ft. lbs. (120 Nm)!
When installed the space around the pump must be
large enough to provide sufficient cooling of the
motor.
The pump must never under any circumstances be
used as a point for securing the piping. No forces or
torques from the piping may be allowed to affect the
pump. Pipes must be intercepted directly before the
pump and connected with no tension.
Edition 02/2018
Page 4 of 12
5.2
Voltage changing ∆ / Y.
Electric wiring
e. g. 220 V – 240 V / 380 V – 420 V, 50 Hz
∆ (Delta Connection)
Y (Star Connection)
All service work must be carried out by qualified
service personnel. Pump must be disconnected
from the power source and all rotating parts must
stand still. Reassure that pump is disconnected
from power source and cannot be switched on.
Verify that there is no voltage at the terminal
board!
According to the European Standard EN809 a motor
overload must be installed and properly set to the full
load amps stated on the pump name plate.
It is the responsibility of the machine operator to
decide whether or not an additional emergency
switch must be installed.
5.2.1
∆ 220 V – 240 V,
50 Hz
There may be no foreign objects such as dirt, particles or humidity inside the terminal board.
Mount terminal board cover to motor tight against
dust and humidity and close up all unused wiring
ports.
ATTENTION
Circuit
Tension voltage and frequency must correspond with
the shown specification on the nameplate.
The pump must be wired so that a solid longterm
electrical connection is ensured. Establish a solid
ground connection.
The electrical wiring must be performed according to the wiring diagram shown inside the terminal box cover. (Please see above sample wiring
diagrams)
Wiring diagram e.g.
Voltage changing 1:2 YY / Y
e.g. 230 / 460 V, 60 Hz
YY
Low Voltage
Y
High Voltage
Circuit on request
Y (Star connection)
up to 7.4 HP
(5.5 kW)
∆ (Delta connection)
8, 8.7, 10.1, 12.1, 14.7, 17.4 HP
(6, 6.5, 7.5, 9, 11, 13 kW)
Y 440 V – 480 V
60 Hz
∆ 440 V – 480 V
60 Hz
BAS6814
Y 380 V – 420 V,
50 Hz
When Variable Frequency Drives are used interfering
signals might occur.
Non-sinus shaped supply voltage from a variable
frequency drive might result in elevated motor temperatures.
6 Start up / Shut down
6.1
Start up
ATTENTION
Switch off at the mains.
After connection the electrical wires, close the terminal box. Briefly start the motor (max. 30 sec.) and
check the rotation according to the arrow on the top
of the motor.
If the direction is incorrect change over two of the
power leads.
6.2 Shut down
All service work must be carried out by qualified
service personnel. Pump must be disconnected from
the power source and all rotating parts must stand
still. Reassure that pump is disconnected from power
source and cannot be switched on. Verify that there
is no voltage at the terminal board!
Open terminal box and disconnect the power leads.
Empty out the pump.
Edition 02/2018
Page 5 of 12
7 Operation
Liquid level
These pumps are not self-priming and must be gravity fed.
Possible leakage must be drained away so as to
prevent any risk to persons or the environment.
NPT ¼
NPT1 ¼
Screw plug
Leakage G 1/8
Oil inspection window
execution-GD only.
If the pump should lock up and cease, shut pump
down (see 6.2) and disconnect from power supply. Pump must be uninstalled and removed from
the system prior to its repair.
8 Servicing and Maintenance
ATTENTION
The surface of the motor must be kept free of dirt.
The motor shaft is spinning in permanently greased
ball bearings (with special grease and increased
bearing play) and does not require any special
maintenance.
8.1 Pumps with double mechanical seal (-GD)
Pumps with double mechanical seal (-GD) are identified by the letters GLRD stamped in on the motor
side of the pump foot and must include an oil receiver
with a capacity of 0.24 litres. Check this through the
inspection window.
Oil receiver Castrol WHITEMOR WOM14 or equivalent oil.
BAS6814
Edition 02/2018
Page 6 of 12
9 Troubleshooting Guide
Fault
Cause
Remedy
Motor does not start, no motor
noise
At least two of the power supply
leads have failed
Check fuses, terminals and supply
leads .
Overload has tripped
Inspect overload
One of the supply leads has failed
See above
Impeller faulty
Motor bearing faulty
Replace impeller
Replace bearing
Overload trips
Pump locked up mechanically
High on/of cycling frequency
Inspect pump hydraulics
Check application
Power consumption is too high
Wrong direction of rotation of
impeller
Lime or other deposits
mechanical friction
See above
High on/off cycling frequency
Wrong power supply (voltage or
cycles)
See above
Power supply must correspond with
name plate rating
Insufficient cooling
Check air flow at motor fan
Pump does not pump
liquid level too low
Pump mechanism faulty
Pipe blocked
Fill up liquid
replace pump mechanism
Clean pipe
Insufficient flow and pressure
Wrong direction of rotation of
impeller
Change over two power supply
leads
Pump mechanism silted up
Worn pump mechanism
Clean pump mechanism
Replace pump mechanism
Incorrect flow or pressure
Wrong power supply (voltage or
cycles)
Power supply must correspond with
name plate rating
Running noise/Vibration
Foreign objects in pump end
Impeller damaged
Bearing/Bushing broken
Remove foreign objects
Replace impeller
Replace bearing/bushing
Motor does not start, humming
noise
Motor overheats
BAS6814
Edition 02/2018
Clean pump mechanism
repair pump
Page 7 of 12
10 Spare part
10.1 Spare part list for Brinkmann Horizontal
End-Suction Pumps Series SBA141S...143S,
Item
1
2
3
4
5
6
7
8
9
9
10
11
12
13
13
14
15
16
16
17
19
22
24
25
26
27
27
28
29
Description
Stator with terminal board
Motor flange
End shield
Terminal box
Retaining ring
Retaining ring
Fan
Fan cover
Ball bearing up to 1.7 HP
Ball bearing 2.6 HP
Ball bearing
Gasket
Pump foot
Retaining ring up to 1.7 HP
Retaining ring 2.6 HP
Spiral-shaped screw 1.7 HP
Socket head cap screw
Stud bolt with bond up to 1.7 HP
Socket head cap screw 2.6 HP
Socket head cap screw
Parallel pin
Shim ring
Mechanical seal
Circlip
Shaft seal up 1.7 HP
Oil inspection window for -GD
Screw plug
Sealing ring
O-ring
BAS6814
DIN 472
DIN 471
DIN 625
DIN 628
DIN 625
DIN 471
DIN 7500
DIN 84
DIN 912
DIN 912
DIN 7
DIN 908
DIN 7603
SBF125S
Item
30
31
50
51
52
53
Description
Shaft seal
Compensation disk up 2.6 HP
Pump body
Motor shaft with rotor
Connection cover
Pump plate with bearing bush
SBA142S, 143S
54 Pump plate SBA143S
55 Impeller
57 Suction screw
59 Spacer sleeve SBA142S, 143S
60 Spacer sleeve SBA143S
61 Running sleeve
62 Bearing bush
63 Spacer ring
64 Woodruff key
67 O-ring
69 Intermediate Cover
72 Socket head cap screw
78 O-ring
82 Joining socket
83 Socket head cap screw
84 Spring washer
85 O-ring
86 Screw plug
87 Sealing ring
91 Insert shaft
93 Shaft clamp
Edition 02/2018
DIN 6888
DIN 912
DIN 912
DIN 7980
DIN 908
DIN 7603
Page 8 of 12
10.2
Indications to the spare part order
Spare parts are available from the supplier.
Standard commercially available parts are to be
purchased in accordance with the model type.
The ordering of spare parts should contain the following details:
1. Pumptype
e.g. SBA141S
2. Pump No.
e.g. 02186814
The date of the construction year is a component
of the pumps type number.
3. Voltage, Frequency and Power
Take item 1, 2 and 3 from the nameplate
4. Spare part with item No.
e.g. connection cover item No. 52
11 Repair Instructions / Replacing the rotary
mechanical seal / the shaft clamp
11.1 Replacing the rotary mechanical seal
Wear safety gloves!
Risk of injury due to sharp edges on pump components, i.e. impeller blades.
circlip (25), the Shim ring (22) and the rotating axial face seal unit (24b-24e).
10)Loosen the Socket head cap screws (17) and
remove the pump body (50).
11)Remove circlip (25), the Shim ring (22) and remove the rotating axial face seal unit (24b-24e).
To replace the insert shaft, see position 11.2).
When changing an axial face seal, remove the
stationary axial face seal unit (24a) from the pump
body (50) and pump foot (12). Clean the seat of
the seal and the pump parts!
The mechanical seal (24) should now be completely replaced. If necessary replace the O-rings
(67, 78) and impellers (55).
12)Fit a new mechanical seal.
The sliding surfaces of the axial face seal must be
free of dirt and grease. Lightly moisten the collar
(24a) with prill water and press the stationary axial
face seal unit (24a) into the pump body (50) and
pump foot (12). Slide the rotating axial face seal
unit (24b-24e) onto quick shaft (91) and fix in position using the Shim ring (22) and the circlip (25).
13)The remaining assembly steps are Pos 3) to 11) in
reverse order.
1) Disconnect the pump electrically and mechanically. Note the markings on the pump components
prior to dismantling. When completely dismantling
a unit with dual axial face seals, drain the medium
in the blocking chamber through the screw plug
(27).
2) Remove the hexagonal head screws (72).
3) Loosen and remove the connection cover (52)
from the pump plate (53). Remove O-ring (67).
4) Remove the suction screw (57).
5) Use two screwdrivers to push the impeller (55)
from the insert shaft (91). Insert the screwdrivers
between the impeller (55) and the pump plate
(53).
6) Remove the woodruff key (64) and the running
sleeve (61) from the insert shaft (91) and remove
the pump plate (53) and O-ring (67).
7) Remove the spacer sleeve (59). Use two screwdrivers to push the impeller (55) from the quick
shaft (91). Insert the screwdrivers between the
impeller (55) and the pump plate (54).
8) Remove the Woodruff key (64) from the insert
shaft (91). Remove the pump plate (54) and the
O-ring (67).
9) Remove the spacer sleeve (60) and use two
screwdrivers to push the impeller (55) from the
quick shaft (91). Insert the screwdrivers between
the impeller (55) and the intermediate cover (69).
Remove the woodruff key (64), the intermediate
cover (69) and O-ring (67). Remove the spacer
ring (63) from the quick shaft (91). Remove the
BAS6814
Edition 02/2018
Page 9 of 12
 Tighten the shaft clamp (∅ 24 mm) for SBA141S,
and SBA142S.
Use a torque screwdriver to tighten each screw
first with 1 ft. lbs. (1.3 Nm) then with 2 ft. lbs. (2.6
Nm) and finally with 3 ft. lbs. (4 Nm) (in a clockwise direction again).
11.2 Dismantling the insert shaft
3
1
2
 Tighten the shaft clamp (∅ 35 mm) for SBA143S.
Use a torque screwdriver to tighten each screw
first with 1.5 ft. lbs. (2 Nm) then with 2.6 ft. lbs.
(3.5 Nm) and finally with 3.7 ft. lbs. (5 Nm) (in a
clockwise direction again)
1 = Shaft clamp
2 = Insert shaft
3 = Motor shaft
1) Disconnect the inline pump from the mains both
electrically and mechanically.
2) Remove the pump.
3) Empty out the Pump and dismantle the pump unit.
11) Mount the pump foot and the pump body.
The remainder of the reassembly process is to be
completed in the opposite order of the prior described
dismantling process.
ATTENTION
Note torques for the screw connections!
Wear safety gloves!
Risk of injury due to sharp edges on pump components, i.e. impeller blades.
4) Dismantle the pump body and the pump foot
5) Loosen the screws on the shaft clamp (1) one
after the other.
12) Position the pump laterally and fill the pump
blocking chamber (-GD) with oil until it reaches the
oil inspection window (27) (0.24 litres). Fit the
sealing ring (28) and screw on the screw plug (27)
When putting the pump back into use, make sure the
direction of rotation is correct!
Tightening torques for screwed connections
Do not, under any circumstances, remove the screws
completely, danger of injury!
6) Pull the extension shaft (2) and the shaft clamp (1)
off the motor shaft (3).
11.3 Assembling the insert shaft and motor shaft
Thread - 
Strength
classes
Tightening
torque ft. lbs.
(Nm)
M5
4.8
M6
8.8
M8
8.8
2.2 (3)
Item
14, 16
3.3 (4.5) 15 (20)
M12
8.8
22 (30)
Item 83
ATTENTION
Clean the contact surfaces of the insert shaft (2)
(inside) and the motor shaft (3). They must not be
lubricated or oiled.
7) Set the motor down on the fan cover.
8) Position the shaft clamp (1) (use a new shaft
clamp) in the centre of the cranked clamping diameter (2) of the insert shaft.
9) Insert the motor shaft (3) into the insert
shaft (2).
10) Tighten:
Mark the first screw and tighten all the screws
evenly by hand, one after the other in a clockwise
direction (not cross-ways).
BAS6814
12 Disposal
When disposing of the pump or the packaging materials the local and national regulation for proper
disposal must be complied with.
Prior to its disposal, the pump must be completely
drained and decontaminated if necessary.
Edition 02/2018
Page 10 of 12
13 Brinkmann Pumps Inc.
Terms and Conditions
The following terms and conditions
govern all quotations made by
Brinkmann Pumps Inc. („Brinkmann“)
and any orders based upon these
quotations. No contract term or condition
shall be amended, deleted or added
without the express written consent of
Brinkmann, and Brinkmann hereby
rejects any terms set forth in any other
writing which are in addition to or different from the terms in this quotation.
These items and conditions and any
other terms and conditions delivered in
writing by an authorized agent of
Brinkmann contemporaneously herewith
constitute the complete agreement
between Brinkmann and the buyer and
supersede all prior oral, written or printed
statements of any kind (including any
terms and conditions submitted by the
buyer and performance or production
data from any source whatsoever,
including references to accuracy, capacity, and capability of products, all of which
are estimates only) made by Brinkmann
or the buyer or their respective representatives. No statement, recommendation or assistance given by Brinkmann or
its representatives to buyer or its representatives, in connection with the use of
any products by buyer, shall constitute a
waiver by Brinkmann of any of the
provisions hereof or affect Brinkmann‘s
liability, as defined herein. All transactions covered hereby and all terms and
conditions of sale shall be governed by
the laws of the state of Michigan.
Prices
The products offered in this proposal and
the prices quoted are based on our
understanding of buyer‘s requirements;
any change in requirements will necessitate a revision in prices quoted. Prices
are F.O.B. our dock, Wixom, Michigan, or
other location as specified on proposal.
Brinkmann‘s prices do not include sales,
use, excise, or similar tax, applicable to
the sale or use of the equipment proposed. These taxes shall be paid by the
buyer, or in lieu thereof, the buyer shall
provide Brinkmann with a tax exemption
certificate acceptable to the taxing
authorities.
Delays or failure to deliver
Brinkmann shall not be responsible for
delay or failure to deliver due to acts of
God, or to government action (civil or
military), or to prior orders, or to fire,
embargo, strike or other labor problems,
wrecks, delays in transportation, unusually severe weather or inability to obtain
necessary labor or materials from the
usual source of supply, or any other
circumstances beyond Brinkmann‘s
control.
BAS6814
Brinkmann shall have the right to furnish
suitable substitutes for materials which
cannot be obtained because of such
force majeure.
Installation
Buyer shall install at its own expense, all
products covered hereby in accordance
with the operating instructions to be
furnished to buyer upon request. Unless
otherwise stated, no installation services
are included in the price indicated.
Limited warranty
Brinkmann warrants to the buyer (but not
to any others) for a period of one year
from date of shipment that all new parts
are free from defects in material and
workmanship.
Brinkmann‘s said warranty shall exist
only if buyer gives written notice to
Brinkmann within ten days after the first
determination that the part is defective
and within the aforesaid one year period
from the date of shipment and includes in
said notice consent to Brinkmann to
inspect, at any reasonable time, said part
and the machine in which it may be
embodied, and if, and only if, Brinkmann
determines to its reasonable satisfaction
upon said inspection that said part and
the machine in which it may be embodied are, and have been, used in accordance with all Brinkmann‘s instructions as
to maintenance and operation set forth in
the operating instructions relating to the
machine. Brinkmann‘s warranty is limited
to shipping to buyer replacement of any
part which is so proven to be defective
and in any event shall have no liability
whatsoever for incidental or consequential damage or loss of profit,
including damages resulting from personal injury or death, or damage to, or
loss of use of, any property. Brinkmann
is not responsible for shipping costs or
labor, extends no warranty of any kind
for gasket, seals and wear and tear
materials. Notwithstanding any provisions of these terms and conditions, this
warranty is the only warranty extended by Brinkmann in connection with
any sales of products and is in lieu of
all other warranties, express or
implied, including warranties of
merchantability or fitness for purpose.
No agent, employee or representative of
Brinkmann has any authority to bind
Brinkmann to any affirmation, representation, or warranty concerning the
products that are the subject of this
quotation beyond that specifically
included in the written quotation.
Brinkmann shall have no obligation to
install or provide improvements or
changes in design adapted by
Brinkmann for similar equipment subsequent to acceptance of buyer‘s order.
Edition 02/2018
Warranties have been discussed and
understood by both parties.
Buyer‘s use and O.S.H.A.
Buyer shall use and require all persons
operating the equipment to use all proper
and safe operating procedures set forth
in operating instructions relating to the
equipment and observe all occupational
safety health and standards act
(O.S.H.A.), American National Standard
Institute (ANSI), and state regulations as
required and all available, feasible and
practical point of operation safety devices consistent with buyer‘s use of the
equipment. Buyer shall not remove or
modify, any device, warning sign,
operating instructions or work handling
tools installed on or attached to the
equipment. Buyer shall notify Brinkmann
promptly, in writing, and in all events
within ten (10) days after its occurrence,
of any accident or malfunction involving
any equipment which results in injury to
or death of persons or damage to
property, or the loss of use thereof and
buyer shall cooperate fully with
Brinkmann in investigation and determining the cause of any such occurrence of
malfunction. At Brinkmann‘s request
made at any time, buyer will either at its
or Brinkmann‘s place of business, permit
to redesign, remodel or revise the
equipment and buyer waives any claims
against Brinkmann for buyer‘s inability to
use the equipment during the time that
same is out of service for such revision,
modification or redesign.
Brinkmann shall not be responsible for
any failure to comply which results from
the location, operation, design, use or
maintenance of the equipment from
alternation of the equipment by persons
or firms other than Brinkmann, or from an
option or accessory to the equipment by
persons or firms other than Brinkmann,
which was available to the buyer but
omitted at the buyer‘s direction, or from
design or instructions furnished by the
buyer or its agents. In view of the above,
Brinkmann does not make any warranties with respect to O.S.H.A. requirements, including noise; and will not be
responsible for fines, penalties, or
consequential damages.
Payment terms
Net payment in full of all invoices is due
thirty (30) days net, unless stated
otherwise in quotation. Any unpaid
balance thereafter shall be subject to a
service charge of 1.75 % per month or, if
illegal, at the highest rate allowed by law.
There shall be no extension or change in
the time for payment due to delay in
installation and/or delays in operation of
the equipment caused by damage,
warranty service or warranty replacement
Page 11 of 12
of parts. If after Brinkmann‘s acceptance
of buyer‘s purchase order, buyer requests Brinkmann to delay shipment of
the equipment, the purchase price shall
become due and owing thirty (30) days
after the equipment is ready for shipment.
If buyer fails to pay the purchase price as
provided herein and Brinkmann institutes
a lawsuit for the collection of said price,
buyer agrees to pay Brinkmann‘s reasonable attorney fees incurred in connection therewith.
Acceptance of orders
Quotations are offered for written acceptance within thirty (30) days from date
(unless otherwise stated) but are subject
to change without notice at any time
before acceptance. If any order contains
printed, stamped or other provisions
inconsistent or in conflict with the terms
and conditions hereof, the terms and
conditions hereof shall control, unless
otherwise specifically stated by
Brinkmann in writing. All clerical errors
are subject to correction in favor of either
party upon notice of either party. All
orders are subject to the credit approval
of Brinkmann. An order containing
subject matter not within the contemplation of the proposal shall be subject to a
further quotation as to price or delivery or
both. Modifications, changes, deferred
shipments, cancellations or additions will
be effective only if accepted by
Brinkmann in writing and then only upon
terms that will indemnify Brinkmann
against all costs and losses.
Title and security agreement
Delivery to carrier shall constitute transfer to the buyer, and all risk of loss or
damage in transit shall be borne by the
buyer.
By execution of a purchase order, buyer
hereby grants to Brinkmann a security
interest in the equipment covered by the
proposal, and its products and/or proceeds in order to secure the payment of
the purchase price thereof and buyer
authorizes to file financing statements
reflecting this security interest without
buyer‘s signature. Buyer will cooperate
with Brinkmann in preparing documents
necessary to perfect this security interest.
Proprietary and other materials
This quotation and all drawings, specifications, materials, patterns, and special
purpose manufacturing aids which are
supplied to buyer by Brinkmann shall be
kept in confidence and shall be listed and
maintained in suitable condition at the
expense of buyer and are to be considered the property of Brinkmann held on
consignment by buyer and to be insured
while in buyer‘s possession. Such
articles and all copies thereof from any
source shall be returned to Brinkmann at
BAS6814
any time upon request and shall not be
used for or by any third parties without
the express written permission of
Brinkmann.
Performance in event of default
In addition to the rights and remedies
conferred upon Brinkmann by law,
Brinkmann will not be required to proceed with the performance of any order
or contract if buyer is in default in the
performance of any order or contract with
Brinkmann and in case of doubt as to
buyer‘s financial condition, shipments
under an order may be suspended or
sent sight draft with bill of lading attached
and Brinkmann may decline further
shipments except for cash before
shipment.
Hold harmless/indemnity
Except to the extent of the limited
warranty set forth above and
Brinkmann‘s own gross negligence or
willful misconduct, buyer hereby:
(1) waives, releases and discharges any
and all claims of any and every kind
(including but not limited to injury or
death of any person or damage to
property), which it may have at any time
against Brinkmann, its agents or employees, by reason of or arising out of
any claimed improper design, specification or manufacture of the equipment
sold hereunder, or of any claimed
inadequate or insufficient safeguards or
safety devices; and (2) covenants to
indemnify and hold harmless Brinkmann,
its agents and employees of, from and
against any and all loss, damage,
expense (including attorney‘s fees),
claims, suits or liability which Brinkmann
or any of its employees may sustain or
incur at any time for or by reason of any
injury or death of any person or persons
or damage to any property, arising out of
any claimed improper design or manufacture of the equipment sold hereunder,
or of any claimed inadequate or insufficient safeguards or safety devices.
judgment of Brinkmann constitute an
improvement over former practice.
Production data, where given, are based
on Brinkmann‘s careful analysis and
understanding of the limits of accuracy,
machinability of materials, amount of
material to be removed, handling facilities provided, and location points but are
nonetheless an estimate only and not
guaranteed or warranted. In no event
shall Brinkmann be responsible for
performance figures supplied by other
parties. If by written agreement the
equipment is to be subject to acceptance
tests before shipment, rejection under
this clause must take place prior to
shipment.
Returned equipment
In no case is equipment to be returned
without first obtaining written permission
from Brinkmann. Unless otherwise
expressly agreed an order for equivalent
value must accompany returned equipment and all such returned equipment
will be accepted for credit only after
inspection. Equipment returned without
good cause and for which no credit is
given shall be subject to a restocking
charge. Buyer returning equipment must
pay transportation charges and bear
risks of loss or damage to goods while in
transit. Acceptance of returned products
by Brinkmann‘s receiving department
shall not bind Brinkmann nor have any
force or effect unless acceptance is
made by Brinkmann in writing.
Electrical equipment
Motors, electrical equipment and wiring
on the equipment quoted will be supplied
in accordance with the manufacturer‘s
standards. Unless specifically quoted
they are not guaranteed to meet ordinances of any local governing body and
the responsibility of conforming to any
local ordinance is assumed by the buyer.
Inspection and testing, production
estimates and performance
All working drawings or other materials
provided by Brinkmann are for general
information purposes only and may or
may not relate to buyer‘s order or other
equipment. Any specifications contained
therein are not binding on Brinkmann
except as expressly so stated.
Brinkmann reserves the right to make, at
any time, such changes in detail of
design or construction as shall in the sole
Edition 02/2018
Page 12 of 12
BAS6814
Edition 02/2018
Page 13 of 12
BAS6814
Edition 02/2018
Page 14 of 12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising