Akai | MPC X | manual | Akai MPC Live Portable Powerhouse Manual

Akai MPC Live Portable Powerhouse Manual
User Guide
English
Manual Version 2.7
Table of Contents
Introduction ............................................................ 7
Basic Concepts ..................................................... 26
System Requirements & Product Support ..... 7
Tutorial ................................................................... 27
About This User Guide ..................................... 7
Important Notes ................................................ 8
Starting Up ....................................................... 27
Setup .................................................................. 8
Creating a Drum Kit......................................... 27
1. Connection ................................................ 8
Creating a Drum Sequence ............................ 29
2. Installation.................................................. 9
Saving & Renaming ......................................... 30
3. Getting Started .......................................... 9
Editing Note Events ......................................... 32
Features ................................................................ 10
Making Basic Sound Edits .............................. 34
MPC X .............................................................. 10
Creating a Bass Track..................................... 36
Top Panel ..................................................... 10
Recording an Audio Track .............................. 39
Navigation & Data Entry Controls ..................... 10
Pad & Q-Link Controls..................................... 11
Mode & View Controls ..................................... 12
Transport & Recording Controls ...................... 13
I/O & Level Controls ........................................ 14
Touchscreen ................................................... 15
Creating a Song ............................................... 40
Exporting the Song .......................................... 41
Other Features Explained ............................... 42
Front Panel .................................................. 16
Rear Panel ................................................... 17
Step Sequencer............................................ 42
MPC Live .......................................................... 18
Drum Loops & Chop Mode .......................... 43
Top Panel ..................................................... 18
Pad Muting & Track Muting ......................... 45
Touchscreen ................................................... 20
Rear Panel ................................................... 21
Sampling (Recording) ................................... 47
MPC Touch ...................................................... 22
Sample Editing ............................................. 49
Top Panel ..................................................... 22
Touchscreen ................................................... 24
Rear Panel ................................................... 25
Recording Automation with the XY Pad ...... 51
Using MPC X or MPC Live as a Controller .. 52
2
Operation .............................................................. 53
General Features............................................. 54
Control Types .............................................. 54
Time Counter/Locate ................................... 79
Timing Correct (TC) ...................................... 81
Metronome (Click/Metro) ............................. 83
Knobs ............................................................. 54
Parameter Values ............................................ 54
Drop-Down Menus / Lists................................ 55
Selectors ......................................................... 55
Buttons ........................................................... 56
Checkboxes .................................................... 56
Tabs ............................................................... 56
Sliders ............................................................. 56
Envelopes ....................................................... 57
Grid View Tools ............................................... 58
Audio Edit Tools .............................................. 59
Automation ................................................... 84
Global ............................................................. 84
Programs & Audio Tracks ................................ 84
16 Level ........................................................ 85
Erase............................................................. 86
Effects .......................................................... 87
Overview ......................................................... 87
Insert Effects ................................................... 89
Pads ........................................................... 89
Programs ..................................................... 60
Keygroups .................................................. 91
About Programs .............................................. 60
Audio Tracks ............................................... 93
Drum Programs............................................... 61
Programs .................................................... 94
Keygroup Programs ........................................ 63
Submixes .................................................... 96
Clip Programs ................................................. 64
Masters ...................................................... 97
Plugin Programs .............................................. 66
Send/Return Effects ........................................ 98
MIDI Programs ................................................ 67
Pads ........................................................... 99
CV Programs .................................................. 68
Keygroups ................................................ 100
Audio Tracks ............................................. 101
Menu ............................................................ 69
Save ............................................................... 70
Programs .................................................. 101
Submixes .................................................. 102
Preferences ..................................................... 71
Info ............................................................. 71
Audio Mixdown .......................................... 103
Wi-Fi ........................................................... 71
Ethernet ...................................................... 72
Battery Usage............................................. 104
Bluetooth .................................................... 72
Sequencer .................................................. 72
Standalone vs. Controller Mode ................ 105
Sync ........................................................... 73
Hardware .................................................... 73
Project Defaults........................................... 74
Project Load/Save ...................................... 75
Record/Export ............................................ 75
General ....................................................... 75
Splice ......................................................... 77
Sync ............................................................... 77
Mode .............................................................. 77
System Resources .......................................... 78
3
Modes............................................................. 107
List Edit Mode ............................................ 232
Main Mode ................................................. 108
Browser ...................................................... 236
Sequence Section ......................................... 113
Browse ......................................................... 236
Track Section ................................................ 121
Program Section ........................................... 130
Grid View ................................................... 135
Sample Assign .............................................. 238
Sampler ...................................................... 239
Sample ......................................................... 242
Audio Edit Mode ........................................ 140
Slice .............................................................. 244
Pad Tap ........................................................ 245
Track View ................................................. 148
MIDI Tracks ................................................... 150
Pad Hold ....................................................... 246
Audio Tracks ................................................. 151
Auto Sampler ................................................ 246
Step Sequencer ......................................... 152
Looper ........................................................ 247
XYFX Mode ................................................ 156
Sample Edit Mode ..................................... 159
Settings......................................................... 161
Pad Mixer ................................................... 252
Levels ........................................................... 254
Panning......................................................... 254
Trim Mode .................................................... 162
Mute ............................................................. 255
Assigning Samples .................................... 166
Send Effects.................................................. 255
Processing Slices & Samples .................... 168
Insert Effects ................................................. 256
Chop Mode ................................................... 173
Converting or Assigning Slices .................. 176
Routing ......................................................... 256
Processing Slices ...................................... 179
Program Mode .............................................. 182
Channel Mixer ............................................ 257
Assigning Samples .................................... 185
MIDI Tracks ................................................... 260
Processing Slices ...................................... 186
Program Edit Mode ................................... 189
Drum Programs............................................. 189
Audio Tracks ................................................. 261
Programs ...................................................... 263
Returns ......................................................... 265
Master ...................................................... 192
Submixes ...................................................... 266
Samples ................................................... 193
Masters ......................................................... 267
Pan Velocity .............................................. 200
Filter/Envelope .......................................... 201
LFO Modulation ........................................ 202
Pad Mute Mode .......................................... 268
Effects ...................................................... 204
Pad Mute ...................................................... 269
Keygroup Programs ...................................... 206
Pad Group .................................................... 270
Master ...................................................... 207
Samples ................................................... 210
Pan Velocity .............................................. 216
Filter/Envelope .......................................... 217
LFO Modulation ........................................ 218
Track Mute Mode ....................................... 271
Track Mute .................................................... 272
Track Group .................................................. 273
Effects ...................................................... 220
Clip Programs ............................................... 222
Next Sequence Mode ................................ 274
Program ................................................... 224
Pad ........................................................... 225
Plugin Programs ............................................ 228
Song Mode ................................................. 276
MIDI Programs .............................................. 229
CV Programs ................................................ 230
Anatomy of an Envelope ................................ 231
4
Q-Link Edit Mode....................................... 279
Addenda ............................................................... 327
Project .......................................................... 281
Program/Audio Track .................................... 283
Updates in MPC 2.1 ....................................... 327
Pad Scene .................................................... 285
Pad Parameter .............................................. 286
Screen .......................................................... 287
New Features ............................................. 327
Exporting Expansions .................................... 327
Pad Color Mode ........................................ 288
Snap: Absolute & Relative ............................. 328
List Edit Settings: Auto-Advance ................... 328
MIDI Control Mode .................................... 290
Pads ............................................................. 291
Buttons ......................................................... 292
Q-Link Knobs ................................................ 293
XY Pad .......................................................... 294
Pitch Quantization ......................................... 329
Step Sequencer: Velocity Adjustment via Q-Links
.................................................................. 330
Pad Perform Mode: User Progressions .......... 330
Faster Attack for Amp Envelopes................... 330
MIDI Learn .................................................... 294
Updates in MPC 2.2 ....................................... 331
Pad Perform Mode .................................... 295
New Features ............................................. 331
MIDI Control Mode: MIDI Learn ..................... 331
Appendix ............................................................. 298
Humanize ...................................................... 332
Generate Random Events ............................. 334
Effects & Parameters.................................... 298
Reverbs ...................................................... 298
Delays ........................................................ 300
Flangers ..................................................... 303
Chorus ....................................................... 304
Autopans.................................................... 304
Tremolos .................................................... 305
Phasers ...................................................... 305
HP (High-Pass) Filters................................ 306
LP (Low-Pass) Filters ................................. 307
Parametric EQs .......................................... 308
Distortions.................................................. 309
Compressors ............................................. 310
Bit Reducers .............................................. 311
Other .......................................................... 312
Project Template ........................................... 336
Updates in MPC 2.3 ....................................... 337
New Features ............................................. 337
Arpeggiator .................................................. 337
Auto Sampler ............................................... 339
Crossfade Looping ....................................... 341
Mode Selection Shortcut .............................. 342
Pad Perform Mode: Chromatic Type ............. 342
Q-Link Navigation Enhancements ................. 342
Split Events .................................................. 343
AIR Instrument Plugins.................................. 344
Plugin Preset Support ................................... 358
Updates in MPC 2.4 ....................................... 359
Glossary ......................................................... 313
SATA Drive Installation ................................. 318
MIDI Machine Control (MMC) ...................... 319
New Features ............................................. 359
AIR FX Bundle ............................................... 359
AIR Instrument Layouts ................................. 370
Clip Program Improvements .......................... 371
FLAC and OGG Support ............................... 371
Technical Specifications .............................. 320
MPC X ........................................................ 320
MPC Live ................................................... 323
MPC Touch ................................................ 325
Mother Ducker .............................................. 371
Next Sequence Mode.................................... 372
Additional Transport Controls ........................ 372
Trademarks & Licenses................................ 326
5
Updates in MPC 2.5 ...................................... 373
New Features ............................................. 373
Splice Integration........................................... 373
Browser Audition Warp and Sync .................. 374
Updates in MPC 2.6 ...................................... 375
New Features ............................................. 375
Ableton Live Set Export ................................. 375
Erase Parameters .......................................... 375
Grid Automation Lanes .................................. 376
Step Automation ........................................... 377
Submixes ...................................................... 378
Workflow Enhancements ............................... 378
Updates in MPC 2.7 ...................................... 379
New Features ............................................. 379
Ableton Live Control ...................................... 379
Akai Network Driver .................................. 379
Configuring Ableton Live ........................... 379
Live Control Mode..................................... 380
Control Bar ............................................... 380
Matrix View ............................................... 381
Mixer View ................................................ 382
Device Control View .................................. 382
Q-Links ..................................................... 382
MPC X Control Map .................................. 383
MPC Live Control Map .............................. 385
Ethernet Adapter Support.............................. 387
Improved Preferences Organization ............... 387
Corrections ................................................ 387
6
Introduction
Thank you for purchasing your MPC. At Akai Professional, we know how serious music is to you. That’s why we
design our equipment with only one thing in mind—to make your performance the best it can be.
This user guide explains how to create music using MPC X, MPC Live, and MPC Touch. There is similar documentation
available for MPC products that use an LCD and for the MPC software application. To view these user guides, click the
Help menu in the MPC software, select MPC Help, and select an option.
Welcome to the MPC family.
Akai Professional
System Requirements & Product Support
For the latest information about this product (system requirements, compatibility information, etc.) and product
registration, visit akaipro.com.
For additional support, visit akaipro.com/support.
About This User Guide
This manual should help you get familiar with using your MPC X, MPC Live, or MPC Touch. For consistency, the
terminology throughout is based on the MPC nomenclature. We also used specific formatting to indicate particular
topics of significance:
Important/Note/Tip: Important or helpful information on a given topic.
Names of buttons, controls, parameters, settings, and other options are written in bold characters throughout the manual.
Examples: Press the Play Start button.
Turn Q-Link Knob 4.
Tap the Mute button.
The Velocity ranges from 0 to 127.
Set the Sample Play selector to One Shot.
Tap BPM, and then use the numeric keypad to enter 120 as the tempo.
Some parts of this manual refer to other relevant chapters or sections, which are cited in bold, italic blue characters.
Click the text to skip immediately to that section.
Examples: Read the Important Notes section before proceeding.
For more information about installing the necessary drivers and software, see Setup > 2. Installation.
To learn more about using send effects, see General Features > Effects > Send/Return Effects.
7
Important Notes
Read the included safety & warranty manual before using your MPC hardware.
Before getting started and connecting devices to your MPC hardware or turning the hardware on/off, make sure all
devices are switched off.
To use your MPC hardware in Controller Mode (to control the MPC software):
Before installing the MPC software, make sure your computer meets the system requirements described at
akaipro.com. This applies whether you’ll use MPC software as your host software or as a plugin in another digital
audio workstation (DAW).
Before connecting your MPC hardware to your computer, install the drivers and software. Visit akaipro.com to
download the latest versions. Refer to the 2. Installation section for more information.
Setup
1. Connection
Here is just an example of how to use MPC X in your setup. Items not listed under Introduction > Box Contents of
your included quickstart guide are sold separately.
Headphones
(to front-panel headphone output)
Footswitch
(to front-panel FS1 input)
Computer
Powered Monitors
SD Card
(to front-panel SD card slot)
USB
drive
Microphone
Turntable
Power
8
Remember to remove the protective film from your MPC hardware touchscreen!
To use your MPC hardware in Standalone Mode, just connect it to a power outlet using the included power
adapter, and power it on!
Note: We highly recommend checking akaipro.com for any available updates to the MPC software/firmware and/or
drivers.
To use your MPC hardware in Controller Mode, continue to Step 2. Installation.
2. Installation
To use your MPC hardware in Controller Mode (to control the MPC software), follow these steps to download
and install the required drivers & software:
1. Go to akaipro.com and register your product. If you don’t have an Akai Professional account yet, you will be
prompted to create one.
2. In your Akai Professional account, download the MPC software package.
3. Open the file and double-click the installer application.
4. Follow the on-screen instructions to complete the installation.
Note: By default, the MPC software will be installed in [your hard drive]\Program Files\Akai Pro\MPC (Windows®)
or Applications (macOS®). You can also create a shortcut on your Desktop.
3. Getting Started
1. Power on your MPC hardware.
2. On your computer, open the MPC software.
3. Follow the on-screen instructions to authorize your version of MPC.
4. You will need an iLok account to complete this. You can create an account at ilok.com.
Make a note of the PACE code in your account, and enter it when asked for it during the authorization/unlock
process.
5. On your MPC hardware, check the upper-right corner of the touchscreen:
•
If there is a monitor/cable icon, then your MPC hardware is already in Controller Mode.
Continue to Step 6.
•
If there is a chip icon, then your MPC hardware is in Standalone Mode. Follow these steps:
i.
Press Menu to enter the Menu.
ii.
Tap the MPC chip icon in the upper-right corner.
iii.
In the Enter Controller Mode window that appears, tap Controller Mode. Looking
for computer may appear briefly on the screen before your MPC hardware recognizes
the USB connection as a controller.
6. In the MPC software, click the Edit menu, and select Preferences. Click the Audio tab and select the sound
card you want to use. Click OK when you are done.
Important:
We highly recommend using your MPC hardware’s sound card (Akai Pro MPC X/Live/Touch ASIO). If you need
to use the internal sound card on a Windows computer, we recommend downloading the latest ASIO4ALL driver
at asio4all.com.
To view the MPC software user guide, click the Help menu in the MPC software, select MPC Help, and select
MPC User Manual.
9
Features
This chapter explains the features and functions of each MPC model with a touchscreen: MPC X, MPC Live, and
MPC Touch.
MPC X
Top Panel
1
55
11
13 14 32 33
28 29 30 31
55
47
48
44
44
45 46 45
51 52
49
50
53 54
16 17 18 19 20
21 23 24 25 26 27
42
6 12
3
8
43
4
5
22
9
10
2
7
15
39
41
40
37 38 36 34 35
Navigation & Data Entry Controls
1. Touchscreen: This full-color multi-touch display shows information relevant to MPC X’s current operation.
Touch the touchscreen (and use the hardware controls) to control the MPC interface. See the later Touchscreen
section to learn how to use some basic functions.
Tip: If you adjust the angle of the touchscreen, use the stand on its back panel to secure it in place.
2. Cursors: Press these buttons to navigate through the fields of menus and options shown on the screen. Press
and hold Shift and press these buttons to zoom in or out of the Grid View or Audio Edit Mode. Press and hold
Shift and press the up and down cursors simultaneously or the left and right cursors simultaneously to return
to the default zoom setting.
10
3. Data Dial: Use this dial to scroll through the available menu options or adjust the parameter values of the
selected field on the screen.
4. –/+: Press these buttons to increase or decrease the value of the selected field on the screen.
5. Numeric Keypad: If the selected field on the screen is a number, press these numbered buttons as you would
on a standard numeric keypad to enter a value. Press the keypad’s Enter to enter it. (A numeric keypad with
additional operations will appear on the screen, as well.)
6. Undo/Redo: Press this button to undo your last action.
Press and hold Shift and press this button to redo the last action you undid.
7. Shift: Press and hold this button to access some buttons’ secondary functions (indicated by red writing).
Double-press this button to see which buttons have secondary functions—the buttons will flash for a few seconds.
8. F-Key: Press this button to activate or deactivate the F-Key feature. When active, the six buttons under the
touchscreen correspond to the options shown at the bottom edge of the screen. The F-Key button and those six
buttons will be lit red when active. When inactive, the six buttons under the touchscreen will access their normal
modes instead (Menu, Browser, Step Seq, Sampler, XYFX, and Looper).
Pad & Q-Link Controls
9. Q-Link Knobs: Turn these touch-sensitive knobs to adjust various parameters and settings. The display strip
above each knob indicates the parameter it is controlling. If the display strip shows a meter to indicate its value,
you can touch or turn its Q-Link knob to temporarily show its precise numerical value.
10. Pads: Press these pads to trigger drum hits or other samples in your software. The pads are velocity-sensitive
and pressure-sensitive, which makes them very responsive and intuitive to play. The pads will light up different
colors, depending on how hard you play them (ranging from yellow at a low velocity to red at the highest
velocity). You can also customize their colors.
11. Pad Bank: Press these buttons to access Pad Banks A–D.
Press and hold Shift while pressing these buttons to access Pad Banks E–H. Alternatively, double-press one of
these buttons.
12. Copy/Delete: Press this button to copy one pad to another. When the From Pad field is selected, press the
“source” pad (the pad you want to copy). When the To Pad graphic (of all pads) is selected, press the
“destination” pad. You can select multiple destination pads, and you can select pads in different pad banks. Tap
Do It to continue or Close to return to the previous screen.
Tip: To quickly copy a pad, press and hold Copy, press the source pad, press the destination pad, and then
release Copy.
Press and hold Shift and press this button to delete a pad’s sample assignment. When the Delete Pad window
is shown, press any pad/pads whose sample assignments you want to clear. Tap Delete to continue or Cancel
to return to the previous screen.
13. Full Level/Half Level: Press this button to activate or deactivate the Full Level feature. When activated, the pads
will always trigger their samples at the maximum velocity (127), regardless of how much force you use.
Press and hold Shift and then press this button to activate or deactivate the Half Level feature. When activated,
the pads will always trigger their samples at half-velocity (64).
14. 16 Level: Press this button to activate/deactivate 16 Level. When activated, the last pad that was hit will be
temporarily copied to all 16 pads. The pads will now output the same note number as the initial pad, but a
selectable parameter will be fixed at values that increase as the pad numbers increase (e.g., Pad 1 is the minimum,
Pad 16 is the maximum), regardless of how hard you press them. In the screen that appears, use the Type selector
to choose the parameter: Velocity, Tune, Filter, Layer, Attack, or Decay. See Operation > General Features >
16 Level to learn more.
15. Note Repeat/Latch: Press and hold this button, and then press a pad to trigger that pad’s sample repeatedly.
The rate is based on the current tempo and Time Correct settings.
Press and hold Shift and then press this button to “latch” the Note Repeat feature. When latched, you do not
have to hold the Note Repeat button for it to be activated. Press Note Repeat once more to unlatch it.
11
16. Project: Press this button to use the Q-Link knobs to adjust parameters related to the current project. Press and
hold Shift and then press this button to enter the Project Q-Link Edit Mode directly. See Operation > Modes >
Q-Link Edit Mode > Project to learn about this.
17. Program: Press this button to use the Q-Link knobs to adjust parameters of the currently selected program or
audio track. Press and hold Shift and then press this button to enter the Program Q-Link Edit Mode directly. See
Operation > Modes > Q-Link Edit Mode > Program to learn about this.
18. Pad Scene: Press this button to use the Q-Link knobs to adjust parameters that you have assigned for the
currently selected pad. Press and hold Shift and then press this button to enter the Pad Scene Q-Link Edit Mode
directly. See Operation > Modes > Q-Link Edit Mode > Pad Scene to learn about this.
19. Pad Param: Press this button to use the Q-Link knobs to adjust one parameter across all 16 pads. Each Q-Link
knob corresponds to the pad with the same number and position in the 4-by-4 layout. Press and hold Shift and
then press this button to enter the Pad Param Q-Link Edit Mode directly. See Operation > Modes > Q-Link Edit
Mode > Pad Parameter to learn about this.
20. Screen Control/Edit: Press this button to use the Q-Link knobs to adjust parameters in the currently selected
mode as shown on the screen. See Operation > Modes > Q-Link Edit Mode > Screen to learn about this.
Press and hold Shift and then press this button to enter Q-Link Edit Mode where you can assign other parameters
to the Q-Link knobs.
Mode & View Controls
Note: See Operation > Modes to learn about the different modes you can access with these controls.
21. Menu: Press this button to open the Menu. You can tap an option in the Menu to enter that mode, view, etc.
22. Main/Track: Press this button to enter Main Mode.
Press and hold Shift and then press this button to enter the Track View.
23. Browse/Save: Press this button to view the Browser. The Browser lets you navigate your computer’s internal
and external hard disks to load samples, sequences, songs, etc. Using filter buttons and user-definable folders,
you can easily adapt it to your workflow. You can also preview samples before loading them.
Press and hold Shift and press this button to save the current project (including its samples, programs, sequences,
and songs).
24. Step Seq/List Edit: Press this button to view the Step Sequencer where you can create or edit sequences by
using the pads as “step buttons,” simulating the experience of a traditional step-sequencer-style drum machine.
Press and hold Shift and press this button to view your sequences using the List Edit View instead of the Grid View.
25. Sampler/Looper: Press this button to view the Sampler where you can record audio samples to use in your
projects.
Press and hold Shift and press this button to view the Looper where you can record and overdub audio in real
time—a great tool for live performance as well as spontaneous moments in the studio. You can export the loop
as a sample to use in your project.
26. XYFX: Press this button to view XYFX Mode, which turns the touchscreen into an XY pad where each axis
represents the range of an effect parameter. As you move touch or move your finger on the screen, the current
position will determine the current value of the two parameters. You can use this mode to create interesting
effect automation on your tracks.
27. Pad Perform: Press this button to view Pad Perform Mode where you can assign musical scales/modes, chords,
or progressions to the pads for creative performance options.
28. Prog Edit: Press this button to view Program Edit Mode, which contains all parameters for editing your programs.
29. Sample Edit: Press this button to view Sample Edit Mode where you can edit your samples using various
functions and processes.
30. Pad Mixer: Press this button to view the Pad Mixer where you can set a program’s levels, stereo panning,
routing, and effects.
31. Ch. Mixer: Press this button to view the Channel Mixer where you can set levels, stereo panning, and other
settings for your tracks, programs, returns, submixes and masters.
12
32. Track Mute/Pad Mute: Press this button to view Track Mute Mode where you can easily mute tracks within a
sequence or set mute groups for each track.
Press and hold Shift and press this button to view Pad Mute Mode where you can easily mute pads within a
program or set mute groups for each pad within a program.
33. Next Seq/Song: Press this button to view Next Sequence Mode where you can trigger different sequences simply
by playing the pads. This is useful for live performances, letting you change a song’s structure in real time.
Press and hold Shift and press this button to view Song Mode where you can arrange sequences in a specific
order and/or repetition to create songs. You can edit the structure of a song during playback for easy, on-the-fly
composing.
Transport & Recording Controls
34. Play: Press this button to play the sequence from the audio pointer’s current position.
35. Play Start: Press this button to play the sequence from its start point.
36. Stop: Press this button to stop playback. You can double-press this button to silence audio that is still sounding
once a note stops playing. Quickly pressing this button three times will act as a “MIDI panic” and shut off all
voices and stop all audio processing.
37. Rec: Press this button to record-arm the sequence. Press Play or Play Start to start recording. Recording in this
way (as opposed to using Overdub) erases the events of the current sequence. After the sequence plays through
once while recording, Overdub will be enabled.
38. Overdub: Press this button to enable Overdub. When enabled, you can record events in a sequence without
overwriting any previously recorded events. You can enable Overdub before or during recording.
39. </> (Event |</>|): Use these buttons to move the audio pointer left or right, one step at a time.
Press and hold Locate and press one of these buttons to move the audio pointer to the previous/next event in
the sequence grid.
40. <</>> (Start/End): Use these buttons to move the audio pointer left or right, one bar at a time.
Press and hold Locate and press one of these buttons to move the audio pointer to the start or end of the
sequence grid.
41. Locate: Press and hold this button to activate the secondary functions of the </> and <</>> buttons (i.e., Event
|</>| and Start/End, respectively).
42. Erase: As a sequence is playing, press and hold this button and then press a pad to delete the note event for
that pad at the current playback position. This is a quick way to delete note events from your sequence without
having to stop playback. See Operation > General Features > Erase to learn more.
43. Tap/Master: Press this button in time with the desired tempo to enter a new tempo (in BPM). You can set how
many taps are required in the Preferences (see Operation > General Features > Menu > Preferences to learn
how to do this).
Press and hold Shift and press this button to set whether the currently selected sequence follows its own tempo
(the button will be lit red) or a master tempo (the button will be lit amber).
13
I/O & Level Controls
44. Gain 1/2: Use these knobs to adjust the gain of the incoming signal from Input 1/2 on the rear panel or Inst 1/2 on
the front panel. Use the Rear/Front switches below the knobs to determine the input. Use the level meter to
check the recording level. Be careful when setting this knob at higher levels, which can cause the signal to distort.
45. Rear/Front: Use each switch to set whether the Gain 1/2 knob above it will control the gain of the input signal on
the rear panel (Input 1/2) or on the front panel (Inst 1/2).
46. Phantom Power (+48V): This switch activates and deactivates phantom power for Input 1/2. When activated,
+48V of phantom power will be supplied to both inputs. Note that most dynamic microphones do not require
phantom power, while most condenser microphones do. Refer to your microphone’s documentation to check if it
needs phantom power.
47. 3/4 Rec Gain: Use this knob to adjust the gain of the incoming signal from Input 3/4 on the rear panel. Use the
level meter to check the recording level. Be careful when setting this knob at higher levels, which can cause the
signal to distort.
48. Master: Turn this knob to adjust the volume level of the Main L/R outputs.
49. Direct/Main: Turn this knob to adjust the balance between the input and output signals in the headphones.
Direct corresponds to the input signal—all devices connected to the inputs on the front and rear panels.
While recording, you can turn this knob all the way to Direct for zero-latency direct monitoring.
Main corresponds to the output signal—the signal sent from the Main L/R outputs on the rear panel. When
you are not recording, we recommend turning this knob all the way to the Main position to hear the fullvolume playback signal.
50. Stereo/Mono: Use this switch to set whether the signal in the headphones is binaural (Stereo) or monaural
(Mono). When set to Stereo, the headphone signal will be split so that the input signal (Direct) is heard in the left
ear while the output signal (Main) is heard in the right ear. When set to Mono, the input and output signals are
blended into a single, summed mix, which is heard in both ears.
51. Rec Arm: Press this button to arm or disarm recording for the currently selected audio track, shown in the
display strip below the level meters (see Operation > General Features > Menu > Preferences to learn how to
set what is shown in the level meters).
52. Read/Write: Press this button to set the automation state for the program on the current track or for the current
audio track: Off, Read (green R), or Write (red W). The display strip below the level meters must show a program
or audio track (see Operation > General Features > Menu > Preferences to learn how to set what is shown in
the level meters).
53. Mute: Press this button to mute the program, audio track, or master output shown in the display strip below the
level meters (see Operation > General Features > Menu > Preferences to learn how to set what is shown in
the level meters).
54. Solo: Press this button to solo the currently selected program or audio track shown in the display strip below the
level meters (see Operation > General Features > Menu > Preferences to learn how to set what is shown in the
level meters).
55. Level Meters: These meters indicate the level of the audio signal shown in the display strip below them. See
Operation > General Features > Menu > Preferences to learn how to set what is shown in the level meters.
14
Touchscreen
Here is some general information about how to use the MPC X touchscreen:
x2
Tap a button or option to select it. Use the data dial or
–/+ buttons to change its setting or value
Double-tap a button to access advanced editing options.
In some cases, this will show a numeric keypad that you
can use to enter a value (an alternative to the data dial
or –/+ buttons). Tap the upper-left part of the screen to
return to the previous view.
Spread two fingers to zoom in (into a section of a
waveform, for example). Pinch two fingers to zoom out.
The top of the screen shows the toolbar, which contains
information about the current view (often the name of
the current track, sequence, audio pointer position,
etc.). Tap an item to select it.
The bottom of the screen shows various buttons that
you can use in the current view. Tap a button to press it.
To return to a previous view, either tap outside of the
window currently on the screen or tap the left arrow ()
in the upper-left part of the screen.
15
Front Panel
1
2
3
4
5
6
1. SD Card Slot: Insert a standard SD/SDHC card into this slot to access its files directly using MPC X.
2. Footswitch Inputs (FS 1/2) (1/4” / 6.35 mm): Connect optional 1/4” (6.35 mm) TS footswitches to these inputs.
3. Instrument Inputs (Inst 1/2) (1/4” / 6.35 mm): Use standard 1/4” (6.35 mm) TS cables to connect these inputs to
audio sources (guitars, bass, etc.). To use each of these inputs, set the corresponding Rear/Front switch (below
the Gain 1/2 knob on the top panel) to Front.
4. Mix Knob: Turn this knob to adjust the balance between the Main and 3/4 signals in your headphones. Main is
the signal sent from the Main L/R outputs. 3/4 is the signal sent from the Outputs 3/4.
5. Headphone Outputs (1/8” or 1/4” / 3.5 mm or 6.35 mm): Connect your headphones (not included) to either or
both of these standard stereo outputs. Use the Mix Knob to determine what signal is heard in the headphones.
Turn the Headphone Volume knob to set the volume level.
6. Headphone Volume: Turn this knob to adjust the volume of the headphone outputs.
16
Rear Panel
9
14
2
6
7
8
11
10
13
12
5 4
1 3
1. Power Input: Use the included power adapter to connect MPC X to a power outlet. This must be connected to a
power outlet in order for MPC X to power on.
2. Power Adapter Restraint: Secure the power adapter cable to this restraint to prevent it from accidentally unplugging.
3. Power Switch: Press this button to turn MPC X’s power on or off. While powered on, press and hold this button
for 5 seconds to force MPC X to power off (similar to a computer).
4. USB-B Port: Use the included USB cable to connect this USB 3.0 port to an available USB 3.0 port on your
computer. This connection allows MPC X to send/receive MIDI and audio data to/from the MPC software on your
computer. It also allows any connected USB drives, SD cards, and drives connected to the internal SATA port to
mount on your computer if MPC X is in Controller Mode (i.e., your computer can access these storage devices
that are connected to your MPC X).
5. USB-A Ports: Connect USB flash drives to these USB ports to access their files directly using MPC X. MPC X
supports read and write capability for exFAT, FAT32, NTFS, and EXT4 file systems as well as read-only capability
for HFS+ file systems. (We recommend using an exFAT file system as it is the most robust one supported by
both Windows and macOS.) These USB ports supply power to connected USB devices and can also be used to
receive MIDI messages from external USB MIDI devices.
6. Inputs 1/2 (XLR or 1/4” / 6.35 mm): Use standard XLR or 1/4” (6.35 mm) TRS cables to connect these inputs to
audio sources (microphone, mixer, synthesizer, etc.). To use each of these inputs, set the corresponding
Rear/Front switch (below the Gain 1/2 knob on the top panel) to Rear. Turn the Gain 1/2 knobs to set the input
level of each one.
Note: When using the XLR connection, the mic pre-amp is automatically engaged. When using a 1/4" (6.35 mm)
TRS cable, the mic pre-amp is bypassed.
7. Inputs 3/4 (1/4” / 6.35 mm or RCA): Use standard 1/4” (6.35 mm) TRS cables or stereo RCA cables to connect
these inputs to audio sources (mixer, turntable, synthesizer, etc.). To use the 1/4” (6.35 mm) inputs, set the
Phono/Line switch to Line. To use the RCA inputs, set the Phono/Line switch to Phono. Turn the 3/4 Rec Gain
knob to set their input levels.
8. Phono/Line Switch: Set this switch to the appropriate position, depending on which Input 3/4 connectors you
want to use. If you are using the 1/4” (6.35 mm) inputs, set this switch to Line. If you are using the RCA inputs,
set this switch to Phono to provide the additional amplification needed for phono-level signals.
9. Grounding Terminal: If you are sending a phono-level turntable signal to the Input 3/4 RCA connectors and are
hearing a low hum or buzz, it could mean that the turntable is not grounded. If the turntable has a grounding
wire, connect it to this terminal.
Note: Some turntables have a grounding wire built into the RCA connection and, therefore, nothing needs to be
connected to the grounding terminal.
10. Main L/R Outputs (1/4” / 6.35 mm): Use standard 1/4” (6.35 mm) TRS cables to connect these outputs to your
speaker system. The signal sent out of these outputs is the master mix. Turn the Master knob to set their volume.
Tip: To route a program to these outputs, set its routing to Out 1,2 in the Channel Mixer when the Mixer field is
set to Programs. See Operation > Modes > Channel Mixer to learn more about this.
11. Outputs 3/4, 5/6, 7/8 (1/4” / 6.35 mm): Use standard 1/4” (6.35 mm) TRS cables to connect these outputs to an
external mixer. The signal sent from these outputs is full-volume (0 dB).
Tip: To route a program to these outputs, set its routing to Out 1,2, Out 5,6, or Out 7,8 (respectively) in the
Channel Mixer when the Mixer field is set to Programs. See Operation > Modes > Channel Mixer to learn
more about this.
12. MIDI In: Use standard 5-pin MIDI cables to connect these inputs to the MIDI outputs of optional external MIDI
devices.
13. MIDI Out: Use standard 5-pin MIDI cables to connect these outputs to the MIDI inputs of optional external MIDI
devices.
14. CV/Gate Out: Use standard 1/8” (3.5 mm) TS cables to connect these outputs to optional external sequencers.
MPC X will send control voltage (CV) and/or Gate data over this connection.
17
MPC Live
Top Panel
6
7
6
8
6
9
6
4
10
3
3
1
5
11 12
13 14 15 16
3
3
2
22 20 21 19 17 18 16
1. Touchscreen: This full-color multi-touch display shows information relevant to MPC Live’s current operation.
Touch the touchscreen (and use the hardware controls) to control the MPC interface. See the later Touchscreen
section to learn how to use some basic functions.
2. Data Dial: Use this dial to scroll through the available menu options or adjust the parameter values of the
selected field on the screen. Pressing the dial also functions as an Enter button.
3. Q-Link Knobs: Use these touch-sensitive knobs to adjust various parameters and settings. The knobs can control
one group of parameters at a time. The lights below the Q-Link button indicate the currently selected column of QLink knobs. Press the Q-Link button to change which parameter or group of parameters they currently control.
4. Q-Link Button: Press this button to change which parameter or group of parameters the Q-Link knobs currently
control (indicated by the lights above the Q-Link knobs). Each press will select the next column of Q-Link knobs.
Press and hold Shift and then press this button to select the previous column of Q-Link knobs instead.
Press and hold this button to show the QLink window over the touchscreen’s current contents. These are the same
parameters and settings as what is shown in Q-Link Edit Mode. You can tap Q-Link Edit at the bottom of the
window to enter Q-Link Edit Mode immediately (see Operation > Modes > Q-Link Edit Mode to learn about this).
5. Pads: Press these pads to trigger drum hits or other samples in your software. The pads are velocity-sensitive
and pressure-sensitive, which makes them very responsive and intuitive to play. The pads will light up different
colors, depending on how hard you play them (ranging from yellow at a low velocity to red at the highest
velocity). You can also customize their colors.
6. Pad Bank: Press any of these buttons to access Pad Banks A–D.
Press and hold Shift while pressing any of these buttons to access Pad Banks E–H. Alternatively, double-press
one of these buttons.
7. Note Repeat/Latch: Press and hold this button, and then press a pad to trigger that pad’s sample repeatedly.
The rate is based on the current tempo and Time Correct settings.
Press and hold Shift and then press this button to “latch” the Note Repeat feature. When latched, you do not
have to hold the Note Repeat button for it to be activated. Press Note Repeat once more to unlatch it.
18
8. Full Level/Half Level: Press this button to activate or deactivate the Full Level feature. When activated, the pads
will always trigger their samples at the maximum velocity (127), regardless of how much force you use.
Press and hold Shift and then press this button to activate or deactivate the Half Level feature. When activated,
the pads will always trigger their samples at half-velocity (64).
9. 16 Level: Press this button to activate/deactivate 16 Level. When activated, the last pad that was hit will be
temporarily copied to all 16 pads. The pads will now output the same note number as the initial pad, but a
selectable parameter will be fixed at values that increase as the pad numbers increase (e.g., Pad 1 is the minimum,
Pad 16 is the maximum), regardless of how hard you press them. In the screen that appears, use the Type selector
to choose the parameter: Velocity, Tune, Filter, Layer, Attack, or Decay. See Operation > General Features >
16 Level to learn more.
10. Erase: As a sequence is playing, press and hold this button and then press a pad to delete the note event for
that pad at the current playback position. This is a quick way to delete note events from your sequence without
having to stop playback. See Operation > General Features > Erase to learn more.
11. Shift: Press and hold this button to access some buttons’ secondary functions (indicated by gray writing).
Double-press this button to see which buttons have secondary functions—the buttons will flash for a few seconds.
12. Menu/Browse: Press this button to open the Menu. You can tap an option in the Menu to enter that mode, view, etc.
Press and hold Shift and then press this button to view the Browser. You can use the Browser to locate and
select programs, samples, sequences, etc.
13. Main/Track: Press this button to enter Main Mode.
Press and hold Shift and then press this button to enter the Track View.
14. Undo/Redo: Press this button to undo your last action.
Press and hold Shift and press this button to redo the last action you undid.
15. Copy/Delete: Press this button to copy one pad to another. When the From Pad field is selected, press the
“source” pad (the pad you want to copy). When the To Pad graphic (of all pads) is selected, press the
“destination” pad. You can select multiple destination pads, and you can select pads in different pad banks. Tap
Do It to continue or Close to return to the previous screen.
Tip: To quickly copy a pad, press and hold Copy, press the source pad, press the destination pad, and then
release Copy.
Press and hold Shift and press this button to delete a pad’s sample assignment. When the Delete Pad window
is shown, press any pad/pads whose sample assignments you want to clear. Tap Delete to continue or Cancel
to return to the previous screen.
16. –/+: Press these buttons to increase or decrease the value of the selected field on the screen.
17. Play: Press this button to play the sequence from the audio pointer’s current position.
18. Play Start: Press this button to play the sequence from its start point.
19. Stop: Press this button to stop playback. You can double-press this button to silence audio that is still sounding
once a note stops playing. Quickly pressing this button three times will act as a “MIDI panic” and shut off all
voices and stop all audio processing.
20. Rec: Press this button to record-arm the sequence. Press Play or Play Start to start recording. Recording in this
way (as opposed to using Overdub) erases the events of the current sequence. After the sequence plays through
once while recording, Overdub will be enabled.
21. Overdub: Press this button to enable Overdub. When enabled, you can record events in a sequence without
overwriting any previously recorded events. You can enable Overdub before or during recording.
22. Tap/Master: Press this button in time with the desired tempo to enter a new tempo (in BPM). You can set how
many taps are required in the Preferences (see Operation > General Features > Menu > Preferences to learn
how to do this).
Press and hold Shift and press this button to set whether the currently selected sequence follows its own tempo
(the button will be lit red) or a master tempo (the button will be lit amber).
19
Touchscreen
Here is some general information about how to use the MPC Live touchscreen:
x2
Tap a button or option to select it. Use the data dial or
–/+ buttons to change its setting or value
Double-tap a button to access advanced editing options.
In some cases, this will show a numeric keypad that you
can use to enter a value (an alternative to the data dial
or –/+ buttons). Tap the upper-left part of the screen to
return to the previous view.
Spread two fingers to zoom in (into a section of a
waveform, for example). Pinch two fingers to zoom out.
The top of the screen shows the toolbar, which contains
information about the current view (often the name of
the current track, sequence, audio playhead position,
etc.). Tap an item to select it.
The bottom of the screen shows various buttons that
you can use in the current view. Tap a button to press it.
To return to a previous view, either tap outside of the
window currently on the screen or tap the left arrow ()
in the upper-left part of the screen.
20
Rear Panel
6
17 12
13 13 13
8 14
10 9
7 11
16
3
15
5 4
1
2
1. Power Input: Use the included power adapter to connect MPC Live to a power outlet.
2. Power Switch: Turns MPC Live’s power on/off.
3. Charging Indicator: This light (behind the vent) will turn on when MPC Live’s internal battery is charging (when
the power input is connected to a power outlet). When the battery is fully charged or when it is disconnected
from a power outlet, then this light will turn off.
4. USB-B Port: Use the included USB cable to connect this USB 3.0 port to an available USB 3.0 port on your
computer. This connection allows MPC Live to send/receive MIDI and audio data to/from the MPC software on
your computer. It also allows any connected USB drives, SD cards, and drives connected to the internal SATA
port to mount on your computer if MPC Live is in Controller Mode (i.e., your computer can access these storage
devices that are connected to your MPC Live).
5. USB-A Ports: Connect USB flash drives to these USB ports to access their files directly using MPC Live. MPC
Live supports read and write capability for exFAT, FAT32, NTFS, and EXT4 file systems as well as read-only
capability for HFS+ file systems. (We recommend using an exFAT file system as it is the most robust one
supported by both Windows and macOS.) These USB ports supply power to connected USB devices and can
also be used to receive MIDI messages from external USB MIDI devices.
6. SD Card Slot: Insert a standard SD/SDHC card into this slot to access its files directly using MPC Live.
7. Rec Vol: Turn this knob to adjust the gain of the incoming signal from the 1/4” (6.35 mm) and RCA inputs. Be
careful when setting this knob at higher levels, which can cause the signal to distort.
8. Master Vol: Turn this knob to adjust the volume of Output 1/2 and the phones output.
9. Inputs (1/4” / 6.35 mm): Use standard 1/4” (6.35 mm) TRS cables to connect these inputs to audio sources
(microphone, mixer, synthesizer, etc.). To use these inputs, set the Line/Phono switch to Line. Turn the Rec Vol
knob to set their input levels.
10. Inputs (RCA): Use a standard RCA stereo cable to connect these inputs to a phono-level audio source like a
turntable. To use these inputs, set the Line/Phono switch to Phono. Turn the Rec Vol knob to set their input levels.
11. Line/Phono Switch: Set this switch to the appropriate position, depending on which inputs you want to use. If
you are using the RCA inputs, set this switch to Phono to provide the additional amplification needed for phonolevel signals. If you are using the 1/4” (6.35 mm) inputs, such as a keyboard or a sampler, set this switch to Line.
12. Grounding Terminal: If using phono-level turntables with a grounding wire, connect the grounding wire to these
terminals. If you experience a low “hum” or “buzz”, this could mean that your turntables are not grounded.
Note: Some turntables have a grounding wire built into the RCA connection and, therefore, nothing needs to be
connected to the grounding terminal.
13. Outputs (1/4” / 6.35 mm): Use standard 1/4” (6.35 mm) TRS cables to connect these outputs to your speaker
system, external mixer, etc. The signal sent out of the Master L/R outputs is the master mix. Turn the Master
Vol knob to set their volume. The signals sent from Outputs 3–6 are full-volume (0 dB).
Tip: To route a program to these outputs, set its routing to Out 1,2, Out 3,4, or Out 5,6 (respectively) in the
Channel Mixer when the Mixer field is set to Programs. See Operation > Modes > Channel Mixer to learn
more about this.
14. Phones (1/8” / 3.5 mm): Connect standard 1/8” (3.5 mm) stereo headphones to this output. Turn the Master Vol
knob to set the volume level.
15. MIDI In: Use standard 5-pin MIDI cables to connect these inputs to the MIDI outputs of optional external MIDI
devices.
16. MIDI Out: Use standard 5-pin MIDI cables to connect these outputs to the MIDI inputs of optional external MIDI
devices.
17. Kensington® Lock Slot: You can use this slot to secure your MPC Live to a table or other surface.
21
MPC Touch
Top Panel
7
8
7
9
7
10
7
5
11
4
1
4
2
4
6
12 13
14 15 16 17
4
3
23 21 22 20 18 19 17
1. Touchscreen: This full-color multi-touch display shows information relevant to MPC Touch’s current operation.
Touch the touchscreen (and use the hardware controls) to control the MPC interface. See the later Touchscreen
section to learn how to use some basic functions.
2. Display Brightness +/–: Use these buttons to increase/decrease the brightness of the touchscreen.
3. Data Dial: Use this dial to scroll through the available menu options or adjust the parameter values of the
selected field in the screen.
4. Q-Link Knobs: Use these touch-sensitive knobs to adjust various parameters and settings. The knobs can control
one group of parameters at a time. The lights below the Q-Link button indicate the currently selected column of QLink knobs. Press the Q-Link button to change which parameter or group of parameters they currently control.
5. Q-Link Button: Press this button to change which parameter or group of parameters the Q-Link knobs currently
control (indicated by the lights above the Q-Link knobs). Each press will select the next column of Q-Link knobs.
Press and hold Shift and then press this button to select the previous column of Q-Link knobs instead.
Press and hold this button to show the QLink window over the touchscreen’s current contents. These are the same
parameters and settings as what is shown in Q-Link Edit Mode. You can tap Q-Link Edit at the bottom of the
window to enter Q-Link Edit Mode immediately (see Operation > Modes > Q-Link Edit Mode to learn about this).
6. Pads: Press these pads to trigger drum hits or other samples in your software. The pads are velocity-sensitive
and pressure-sensitive, which makes them very responsive and intuitive to play. The pads will light up different
colors, depending on how hard you play them (ranging from yellow at a low velocity to red at the highest
velocity). You can also customize their colors.
7. Pad Bank: Press any of these buttons to access Pad Banks A–D.
Press and hold Shift while pressing any of these buttons to access Pad Banks E–H. Alternatively, double-press
one of these buttons.
8. Note Repeat/Latch: Press and hold this button, and then press a pad to trigger that pad’s sample repeatedly.
The rate is based on the current tempo and Time Correct settings.
Press and hold Shift and then press this button to “latch” the Note Repeat feature. When latched, you do not
have to hold the Note Repeat button for it to be activated. Press Note Repeat once more to unlatch it.
22
9. Full Level/Half Level: Press this button to activate or deactivate the Full Level feature. When activated, the pads
will always trigger their samples at the maximum velocity (127), regardless of how much force you use.
Press and hold Shift and then press this button to activate or deactivate the Half Level feature. When activated,
the pads will always trigger their samples at half-velocity (64).
10. 16 Level: Press this button to activate/deactivate 16 Level. When activated, the last pad that was hit will be
temporarily copied to all 16 pads. The pads will now output the same note number as the initial pad, but a
selectable parameter will be fixed at values that increase as the pad numbers increase (e.g., Pad 1 is the minimum,
Pad 16 is the maximum), regardless of how hard you press them. In the screen that appears, use the Type selector
to choose the parameter: Velocity, Tune, Filter, Layer, Attack, or Decay. See Operation > General Features >
16 Level to learn more.
11. Erase: As a sequence is playing, press and hold this button and then press a pad to delete the note event for
that pad at the current playback position. This is a quick way to delete note events from your sequence without
having to stop playback. See Operation > General Features > Erase to learn more.
12. Shift: Press and hold this button to access some buttons’ secondary functions (indicated by gray writing).
Double-press this button to see which buttons have secondary functions—the buttons will flash for a few seconds.
13. Menu/Browse: Press this button to open the Menu. You can tap an option in the Menu to enter that mode, view, etc.
Press and hold Shift and then press this button to view the Browser. You can use the Browser to locate and
select programs, samples, sequences, etc.
14. Main/Track: Press this button to enter Main Mode.
Press and hold Shift and then press this button to enter the Track View.
15. Undo/Redo: Press this button to undo your last action.
Press and hold Shift and press this button to redo the last action you undid.
16. Copy/Delete: Press this button to copy one pad to another. When the From Pad field is selected, press the
“source” pad (the pad you want to copy). When the To Pad graphic (of all pads) is selected, press the
“destination” pad. You can select multiple destination pads, and you can select pads in different pad banks. Tap
Do It to continue or Close to return to the previous screen.
Tip: To quickly copy a pad, press and hold Copy, press the source pad, press the destination pad, and then
release Copy.
Press and hold Shift and press this button to delete a pad’s sample assignment. When the Delete Pad window
is shown, press any pad/pads whose sample assignments you want to clear. Tap Delete to continue or Cancel
to return to the previous screen.
17. –/+: Press these buttons to increase or decrease the value of the selected field in the screen.
18. Play: Press this button to play the sequence from the audio pointer’s current position.
19. Play Start: Press this button to play the sequence from its start point.
20. Stop: Press this button to stop playback. You can double-press this button to silence audio that is still sounding
once a note stops playing. Quickly pressing this button three times will act as a “MIDI panic” and shut off all
voices and stop all audio processing.
21. Rec: Press this button to record-arm the sequence. Press Play or Play Start to start recording. Recording in this
way (as opposed to using Overdub) erases the events of the current sequence. After the sequence plays through
once while recording, Overdub will be enabled.
22. Overdub: Press this button to enable Overdub. When enabled, you can record events in a sequence without
overwriting any previously recorded events. You can enable Overdub before or during recording.
23. Tap/Master: Press this button in time with the desired tempo to enter a new tempo (in BPM). You can set how
many taps are required in the Preferences (see Operation > General Features > Menu > Preferences to learn
how to do this).
Press and hold Shift and press this button to set whether the currently selected sequence follows its own tempo
(the button will be lit red) or a master tempo (the button will be lit amber).
23
Touchscreen
Here is some general information about how to use the MPC Touch touchscreen:
x2
Tap a button or option to select it. Use the data dial or
–/+ buttons to change its setting or value
Double-tap a button to access advanced editing options.
In some cases, this will show a numeric keypad that you
can use to enter a value (an alternative to the data dial
or –/+ buttons). Tap the upper-left part of the screen to
return to the previous view.
Spread two fingers to zoom in (into a section of a
waveform, for example). Pinch two fingers to zoom out.
The top of the screen shows the toolbar, which contains
information about the current view (often the name of
the current track, sequence, audio playhead position,
etc.). Tap an item to select it.
The bottom of the screen shows various buttons that
you can use in the current view. Tap a button to press it.
To return to a previous view, either tap outside of the
window currently in the screen or tap the left arrow ()
in the upper-left part of the screen.
24
Rear Panel
2 1 3 4
8
6
7
9
5
10
11
1. Power Input: Use the included power adapter to connect MPC Touch to a power outlet. Alternatively, you can
power MPC Touch via the USB port only, but the touchscreen will be disabled.
2. Power Switch: Turns MPC Touch’s power on/off.
3. USB Port: Use the included USB cable to connect this high-retention-force USB port to an available USB port on
your computer. This connection allows MPC Touch to send/receive MIDI and audio data to/from the MPC software.
You can power MPC Touch via the USB port only, but the touchscreen will be disabled.
4. Rec Vol: Turn this knob to adjust the gain of the incoming signal from the inputs. Be careful when setting this
knob at higher levels, which can cause the signal to distort.
5. Master Vol: Turn this knob to adjust the volume of the outputs and phones output.
6. Inputs (1/4” / 6.35 mm): Use standard 1/4” (6.35 mm) TRS cables to connect these inputs to audio sources
(microphone, mixer, synthesizer, etc.). Turn the Rec Vol knob to set their input levels.
7. Outputs (1/4” / 6.35 mm): Use standard 1/4” (6.35 mm) TRS cables to connect these outputs to your speaker
system, external mixer, etc. The signal sent out of these outputs is the master mix. Turn the Master Vol knob to
set the volume level.
Tip: To route a program to these outputs, set its routing to Out 1,2 in the Channel Mixer when the Mixer field is
set to Programs. See Operation > Modes > Channel Mixer to learn more about this.
8. Phones (1/8” / 3.5 mm): Connect standard 1/8” (3.5 mm) stereo headphones to this output. Turn the Master Vol
knob to set the volume level.
9. MIDI Out (1/8” / 3.5 mm): Use the included 1/8”-to-5-pin adapter and a five-pin MIDI cable to connect this
output to the MIDI input of an optional external MIDI device.
Important: Do not connect audio devices (e.g., headphones, monitors, etc.) to the MIDI Out. Use the included
1/8”-to-5-pin adapters to connect MIDI devices only.
10. MIDI In (1/8” / 3.5 mm): Use the included 1/8”-to-5-pin adapter and a five-pin MIDI cable to connect this input to
the MIDI output of an optional external MIDI device.
Important: Do not connect audio devices (e.g., headphones, monitors, etc.) to the MIDI In. Use the included
1/8”-to-5-pin adapters to connect MIDI devices only.
11. Kensington® Lock Slot: You can use this slot to secure your MPC Touch to a table or other surface.
25
Basic Concepts
This chapter should help explain some fundamental aspects of the MPC universe.
The MPC workflow is quite different from traditional digital audio workstations (DAWs). In most typical DAWs, each track
uses an instance of each instrument, and all tracks are always playing even if they don’t contain any audio or MIDI
information. Furthermore, your entire project needs to be arranged just as the resulting song would be. This isn’t the case
with MPC, which offers much more flexibility within your project. It’s important to understand some basic terms, though:
A sequence is a “building block” of a song. It contains multiple tracks that play at the same time like a normal
DAW. In a project, you might create one sequence for your verse and another sequence for your chorus, alternating
and/or repeating each one in a specific order to create the song. (A project can contain 128 sequences.)
A track is a layer in a sequence. There are two types of tracks:
MIDI tracks consist of MIDI data only, no audio data. These tracks produce sound by using programs,
described below. Unlike a normal DAW, each MIDI track exists only in its sequence. The advantage of this is
not having to manage empty or unwanted tracks across all of your sequences—each sequence contains only
the tracks you want to use in it. If you want to use the same track across multiple sequences, you can copy
the track from one sequence into another. (A sequence can contain 128 MIDI tracks.)
Audio tracks consist of a recorded audio signal, like a traditional DAW. These tracks do not use programs
because the audio is already contained in the track. Also, unlike MIDI tracks, audio tracks are present in
every sequence in the project, even if the tracks themselves are empty. (A sequence on your MPC hardware
can contain 8 audio tracks. A sequence in the MPC software can contain 128 audio tracks.)
A program is a preset through which MIDI tracks are routed. Programs may contain audio samples that are
triggered when tracks play through them, producing the sound you want on that track. Programs are
independent of tracks and sequences, so you can set multiple tracks to use the same program (unlike normal
DAWs where each track requires its own set of samples). Furthermore, you can use the same program/programs
across multiple sequences. (A project can contain 128 programs.)
Each program can be played using the 16 pads (across eight pad banks, which gives you access to 128 pads in
each program). Each pad plays a MIDI note when you press it, but that MIDI note will trigger something different
for each program. For instance, in drum programs, the pads are assigned to samples—one pad could trigger a
kick drum sound and another could trigger a snare drum sound—whereas in keygroup programs, each pad
triggers a MIDI note that plays the corresponding pitch of the sample assigned to its keygroup.
Here’s a diagram to illustrate an example of how these pieces could work together:
Sequence
Drum Program
(Drums)
Track (MIDI: Drums)
Keygroup Program
Track (MIDI: Bass)
(Bass)
Track (MIDI: Keys 1)
Keygroup Program
(Keys)
Track (MIDI: Keys 2)
Keygroup Program
Track (MIDI: Synth)
(Synth Lead)
Track (Audio: Vocals)
Mixing
Track (Audio: Vocals)
Track (Audio: Guitar)
Please take a look at the following Tutorial chapter, as well. It will walk you through the creation of a short song to
show you some of your MPC hardware’s most important features.
26
Tutorial
This chapter should familiarize you with some basic MPC features. We’ll create a short song to illustrate some of the
most important features. To get the most out of this chapter, we recommend reproducing each of the described steps.
Starting Up
Make sure you have completed all of the steps described in Introduction > Setup. This includes:
•
Installing the most current drivers and software.
•
Connecting your MPC hardware to a power source using the included power adapter (if required) and
powering it on.
•
Opening and authorizing your MPC software (if you are using your MPC hardware as a controller).
Creating a Drum Kit
Let’s start by making a simple drum kit.
Press Browse (MPC X) or Shift+Menu/Browse (MPC Live, MPC Touch) to show the Browser. Then, use the
touchscreen to navigate to where your drum sounds are located:
To browse your files by location, tap Places on the left side of the screen.
Internal is the internal drive of MPC X or MPC Live.
MPC Documents is a shortcut to the MPC Documents folder on the internal drive of MPC X or MPC Live.
If you have storage devices connected to USB ports or SD card slot of MPC X, MPC Live, or your computer
(with MPC Touch), they will appear in this column, as well.
Important: MPC X and MPC Live support read and write capability for exFAT, FAT32, NTFS, and EXT4 file
systems as well as read-only capability for HFS+ file systems. (We recommend using an exFAT file system as it
is the most robust one supported by both Windows and macOS.)
To browse your files by type, tap Content and then tap the type of file: Drums, Instruments, Clips, Samples,
Demos, or My Files.
To browse your MPC Expansions (MPC X or MPC Live only), tap Expansions (see Addenda > Updates for
MPC 2.1 > New Features > Exporting Expansions to learn how to export MPC Expansions from your computer
to your MPC X or MPC Live).
To move up one folder level, tap the folder/ icon in the upper-left corner.
To move through a list, swipe up or down, turn the data dial or use the –/+ buttons.
To select a file or folder, tap it once.
To enter a folder, double-tap it or tap Open in the lower-right corner. Alternatively, press the center cursor or
Enter (MPC X) or the data dial (MPC Live, MPC Touch) to enter a selected folder.
27
To load a selected file, double-tap it, tap Load, or press the center cursor or Enter (MPC X) or the data dial
(MPC Live, MPC Touch). If the file is a sample, it will be loaded to the project’s sample pool. If the file is a
project, it will be loaded in its entirety (you will be asked if you want to close your current project).
To load all files in a folder, select the folder (so it is highlighted in the list), press and hold Shift, and then tap
Load All in the lower-right corner.
Important: Although you can load multiple files at once, any samples you load into a project will be automatically
converted to full-quality uncompressed audio files, so they may use more storage space than they do on your
external storage device. If you are unable to load multiple files at once due to this, select fewer files and try again.
To delete a selected file or folder, press and hold Shift and then tap Delete File at the bottom of the screen.
To preview a selected sound, tap and hold Play () at the bottom of the screen.
To enable or disable the audition function and set its volume level, tap Audition at the bottom of the screen.
In the screen that appears, tap Auto to enable or disable it, and tap and drag the level slider up or down to set
the volume level. Tap Audition once more to hide the window.
To show the information for the current drive (MPC X, MPC Live), press and hold Shift and then tap Drive
Info at the bottom of the screen. The drive’s information will appear in a new window. Tap OK to return to the
previous screen.
After loading samples for a drum kit into the sample pool,
use the Sample Assign tab to assign a kick drum sound to
a pad:
1. Tap Sample Assign at the bottom of the screen. This
lets you view the pads and project’s sample pool.
2. Press Pad 1 or tap Pad 1 on the screen to select it. The
pad will be lit green.
3. Swipe the Sample Pool list up or down or use the data
dial or –/+ buttons to move through it.
4. To load a sample to the selected pad (Pad 1, in this
case) tap it in the Sample Pool list, or press the center
cursor or Enter (MPC X) or the data dial (MPC Live,
MPC Touch). Now, you can press Pad 1 to play the kick
drum sample.
To create a simple drum kit, repeat the above steps for
other pads. We recommend loading a snare drum, a closed
hi-hat, and an open hi-hat.
28
Creating a Drum Sequence
Now that your drum kit is set up, let’s record a drum sequence.
1. Press Menu to enter the Menu, and then tap Grid View.
2. Press Tap repeatedly at the speed you want to record your sequence. Your MPC hardware will detect the rate
and adjust itself automatically.
3. Press the Rec button to record-arm the sequence.
4. Press the Play button to start the actual recording. You will hear the count-in for one measure before the
recording starts. We recommend recording only one sound (pad) at a time, especially if you’re not familiar with
playing drums on the pads.
5. Play a simple kick drum pattern. The note events you just recorded will automatically be placed in the grid (in this
case, on 16th notes). The initial measure length is two bars. After the two bars, the recording will automatically
activate Overdub; the sequence will play again from the beginning and keeps looping, allowing you to record
further notes. Don’t stop the recording!
6. Play the snare drum part, then a hi-hat part.
7. When you’re done recording, press the Stop button.
If you start recording again on this sequence, keep in mind that the pads you play in your new recording will replace
existing notes played with the same pads. To prevent this, press the Overdub button before recording instead of the
Rec button. Overdub lets you record additional note events over the existing sequence.
The Undo button functions differently while recording. Normally, pressing Undo will undo just the last event. When
there is an event to undo, the Undo button will be lit solid. While recording, the Undo button will flash. In this case,
pressing Undo will erase all events from that recording (i.e., since Play or Play Start was pressed).
29
Saving & Renaming
We recommend doing some renaming of your programs and samples before going further.
The collection of drum samples you loaded earlier (and their respective pad assignments) are arranged into a
program. When you load this program in the future, you will be able to use all of the samples that belong to it.
Let’s rename the existing program as we’ll want to create more programs later on.
To rename a program:
1. Press Main to enter Main Mode.
2. In the Program section in the lower part of the screen, tap the cursor icon on the right edge.
3. Use the virtual keyboard that appears to enter a new name (e.g., Drums), and then tap Do It.
To rename your samples:
1. Press Menu to enter the Menu, and then tap Sample Edit to enter Sample Edit Mode.
2. The Sample field at the top of the screen will show the name of a sample. Select a sample in one of the following
ways:
•
When the Sample field is selected, use the data dial or –/+ buttons to change it.
•
Double-tap the Sample field and tap one in the list that appears.
3. Tap the keyboard icon next to it to rename the current sample.
4. Use the virtual keyboard that appears to enter a new name (e.g., Kick, Snare, etc.), and then tap Do It.
Repeat Steps 2–4 to rename other samples.
30
Now would be a good time to save your project.
To save your project, press Menu to show the Menu, and tap the disk icon at the top of the screen to open the
Save window. Alternatively, press Shift+Browse/Save (MPC X). In the Save window, do any of the following:
To select the storage device you want to view, tap it in the Storage column on the left.
Internal is the internal drive of MPC X or MPC Live.
MPC Documents is a shortcut to the MPC Documents folder on the internal drive of MPC X or MPC Live.
If you have storage devices connected to USB ports or SD card slot of MPC X, MPC Live, or your computer
(with MPC Touch), they will appear in this column, as well.
To enter a folder, double-tap it. Alternatively, turn the data dial or use the –/+ buttons to move through the list,
and press the center cursor or Enter (MPC X) or the data dial (MPC Live, MPC Touch) to enter a folder. You
can also tap one of the five folder buttons in the upper-right to jump immediately to those pre-assigned file
paths (see Operation > Modes > Browser to learn how to do this).
To create a new folder, tap New Folder, use the virtual keyboard that appears to enter a name, and then tap
Do It. You will immediately enter the new folder.
To move up one folder level, tap the folder/ icon in the upper-left corner.
To name the file, tap the File Name field at the bottom of the screen, and use the virtual keyboard that appears.
To save the file, tap Save.
To cancel and return to the Menu, tap Cancel. Alternatively, tap the  icon in the upper-left corner.
31
Editing Note Events
In the grid, you can see your recorded notes (or note events) as a sequence.
To enter the Grid View, press Menu, and then tap Grid View.
In the Grid View, you can do any of the following:
To zoom in or out, tap the magnifying-glass icon in the upper-right corner. Then, in the grid, spread two
fingers apart or pinch two fingers together. You can do this for each axis, horizontal or vertical.
To automatically set the grid to view one pad bank and two bars, tap the grid-and-magnifying-glass icon in
the lower-left corner.
To undo your last action, press Undo.
To redo the last action you undid, press Shift+Undo/Redo.
To enter a note, tap the pencil icon in the upper-right corner. Then, in the grid, tap a square.
To delete a note, tap the eraser icon in the upper-right corner. Then, in the grid, tap a note.
To select a single note, tap the select box in the upper-right corner. Then, in the grid, tap the note.
To select all notes for a pad, press the desired pad.
To move the selected notes, tap Nudge at the bottom of the screen, and then use the data dial or –/+ buttons
to shift the notes left or right. By default, you can position notes only by quantization values defined by the Time
Correct value (learn about this feature in Operation > General Features > Timing Correct (TC)).
To move the selected notes without restricting (“snapping”) them to the quantization grid, tap and hold
Don’t Snap in the lower-left corner of the screen, and then use the data dial or –/+ buttons to shift the notes. In
this case, each nudge is equivalent to four ticks.
To adjust the start point or end point of the selected notes (without changing their position), tap Edit Start or
Edit End at the bottom of the screen, and then use the data dial or –/+ buttons.
To transpose the selected notes up or down, tap Transpose at the bottom of the screen, and then use the
data dial or –/+ buttons.
To switch to the previous or next track, tap the Track field in the upper-left corner, and then use the data dial
or –/+ buttons.
To mute or solo the track, press and hold Shift, and then tap Mute or Solo (respectively) at the bottom of the
screen.
32
To open the Timing Correct window, press and hold Shift, and then tap TC at the bottom of the screen. See
Operation > General Features > Timing Correct (TC) to learn about this.
To adjust the velocity of the selected notes, tap Velocity at the bottom of the screen, and then use the data
dial or –/+ buttons. The numeric value will appear on the screen.
To show or hide the velocity lane, tap the up arrow (∧) button in the lower-right corner of the screen to show
the velocity lane below the grid. Each note’s velocity is represented by a vertical bar. The higher and more red
the bar is, the higher the velocity is.
Tap the up arrow (∧) button once more to show a taller version of the velocity lane after which it will turn into a
down arrow (∨) button, which you can then tap to hide the velocity lane.
33
Making Basic Sound Edits
Let’s make sure the samples are properly tuned and have good levels.
Press Menu, and then tap Program Edit to enter Program Edit Mode. Alternatively, press Prog Edit (MPC X).
Press a pad to show its parameters on the screen.
To adjust its volume, tap and drag the Volume knob up or down. Alternatively, use the data dial or –/+ buttons.
To make finer adjustments, double-tap the knob and adjust the larger version that appears. Tap anywhere else
to return to the previous screen.
To adjust its stereo panning, tap and drag the Pan knob up or down. Alternatively, use the data dial or –/+
buttons. To make finer adjustments, double-tap the knob and adjust the larger version that appears. Tap
anywhere else to return to the previous screen.
Adjust the level of each pad to suit your taste. We recommend spreading the panning of the bright sounds (e.g.,
cymbals, snare drum) a little. Additionally, you can tune the kick drum sound—tap the Samples tab so the first
square under it is lit, and then adjust the Semi and Fine knobs next to the sample name.
34
The snare drum may need some reverb to give it a more spatial sound.
Tap Effects at bottom of the screen to view the Insert Effects tab. Press the pad with your snare drum sound to
select it.
To add an effect:
1. Double-tap the desired slot. A list of effects will appear.
2. Swipe up or down to move through the list.
3. To load an effect, double-tap it. Alternatively, tap it once and then tap Select or push the data dial. Let’s try
Reverb Medium.
4. To close the list, tap Close.
To adjust the effect’s parameters, tap the pencil icon.
To empty the effect slot, tap the trash can icon. Switch the effect on or off by tapping the On/Off button for the slot.
35
Creating a Bass Track
Let’s try recording a bass line. Unlike a drum kit, it’s important to be able to play and record a bass sound
chromatically, so this will be slightly different than setting up the drum kit.
Adding a bass line over the drum part means we need to work on a new track. A track is simply a layer of a sequence.
Each track uses a program within your project. You can work with multiple tracks in a single sequence (e.g., a drum
track, a bass track, a piano track, etc.). When you play the sequence, all of them will play simultaneously.
First, let’s make an empty track.
To select a new track:
1. Press Main to go back to Main Mode.
2. Double-tap the Track field in the center-left part of the screen, and then tap Track 2 (unused) in the list of tracks
that appears.
Alternatively, tap the Track + button at the bottom of the screen until (unused) appears in the Track field.
Let’s create a new program for this track to use.
To create a new program:
1. In the Track section in the middle of the screen, tap the piano-keys icon. This icon indicates a keygroup
program, which is necessary to play the bass sound chromatically with the pads.
A name for the new keygroup program will appear in the Program field in the lower part of the screen.
2. In the Program section in the lower part of the screen, tap the cursor icon on the right edge.
3. Use the virtual keyboard that appears to enter a new name, and then tap Do It.
36
To load and edit a bass sound:
1. Press Browse (MPC X) or Shift+Menu/Browse (MPC Live, MPC Touch) to show the Browser. Then, use the
touchscreen to navigate to where your bass sounds are located, and load one to the project’s sample pool. (You
can look at this earlier section if you forgot how to do this!)
2. After loading a bass sample to the sample pool, don’t use the Sample Assign tab like you did when creating a
drum program; keygroup programs are different.
Instead, press Menu, and then tap Program Edit to enter Program Edit Mode. Alternatively, press Prog Edit (MPC X).
3. In Program Edit Mode, tap the Samples tab at the bottom of the screen to show the four layers of samples in the
program.
4. Double-tap the first Layer field and then tap your bass sample in the list on the left. Because you’re working with
a keygroup program instead of a drum program, this sample is now playable across all pads.
Tip: On your MPC hardware, press the Pad Bank D button to switch to Pad Bank D and press Pad 13. You
should hear the bass sample played back with its original pitch. You can use the other pads to play your sample
chromatically.
Let’s add a second layer and set the layers’ velocity ranges so the bass will sound different when played at a higher
velocity (as a real bass would):
1. Press Browse (MPC X) or Shift+Menu/Browse (MPC Live, MPC Touch) to show the Browser, select a different
bass sample that sounds similar but a little bit brighter, and load it to the project’s sample pool.
2. Return to Program Edit Mode, and in the Layer tab, double-tap the second Layer field, and select the new bass
sample. Press a pad to hear both samples will sound at once. Maybe this new sound is interesting as it is, but
let’s make some quick edits to get as close as we can to a real-life bass sound.
3. Tap the Pan Velocity tab to show its parameters.
4. Tap Layer 1’s Vel End knob and turn the data dial to set it to 80. Do the same to set Layer 2’s Vel Start slider to 81.
Now when you press a pad, the lower velocities (0–80) will trigger the Layer 1 sample only, while higher velocities
(81–127) will trigger the Layer 2 sample only.
37
Let’s record that bass line now. Prepare your recording as described earlier, and record some bass notes. You can
edit your recording just like we’ve done earlier.
Once you’ve recorded it, let’s tweak the sound a bit in the Filter section:
1. In Program Edit Mode, tap the Filter/Env tab to show its parameters.
2. Double-tap the Type drop-down menu, and select a filter. Let’s try working with Lowpass 4 Pole.
3. Tap the Cutoff or Reso (resonance) knob, and turn the data dial to adjust their settings until your bass sample
sounds good to you.
4. In the Amp Envelope section, tap the Attack or Release knob, and turn the data dial to adjust their settings.
These control the overall level characteristics of the sound.
Do you want to add an effect? Do this in the Effects tab:
1. Tap the Effects tab to show the insert effects.
2. Double-tap one of the Inserts slots to show a list of available effects.
3. Double-tap the effect you want to add to your bass line, or click Close to cancel.
To adjust the settings of the effect, click the pencil icon next to its slot to open a window that shows its
parameters.
To activate or deactivate all insert effects for that program, click the All On/All Off button in the upper-right
corner.
So far, we’ve created a simple drum sequence and a bass line to go with it. Repeat this process to create a second
sequence.
38
Recording an Audio Track
We’ve already created some MIDI tracks, so let’s record some actual audio for our next track:
1. Press Main to go back to Main Mode.
2. Tap the Audio tab at the bottom of the screen. Audio 001 will appear in the Track field.
3. If the channel strip is not already shown on the left side of the screen, tap Input Config (in the lower part of the
screen) or the small eye icon (in the upper-left part of the screen) to show it.
4. Connect a synthesizer or other line-level audio source to the 1/4” (6.35 mm) input/inputs on your MPC
hardware’s rear panel, and set the Line/Phono selector to Line (MPC X, MPC Live).
5. Double-tap the first field (Input __) and select Input 1 or Input 1,2 (depending on your audio source) as the input
source.
6. If the second field is not set to Out 1,2, double-tap it and select that option as the output.
7. Tap the Monitor button to cycle through its three states until it reads Auto (you will hear incoming audio while
the track is record-enabled only).
8. Turn the 3/4 Rec Gain (MPC X) or Rec Vol (MPC Live, MPC Touch) knob to set the input level while playing your
audio source. You should now see the level in the meter. Make sure it does not exceed the maximum level (the
meter should not be “peaking” constantly).
9. If Solo and Mute are on, tap or press them so they are off. Also, tap the automation button so it is off/gray (not
green/Read [R] or red/Write [W]). Alternatively, press Read/Write (MPC X).
10. Tap the Record Arm button to record-enable the track. Alternatively, press Rec Arm (MPC X).
11. Press Rec to record-arm the sequence.
12. To start recording, press Play or Play Start—then play your audio source! You should hear your existing
sequence playing in the background.
To stop recording, press Stop.
Record another audio track for your other sequence: Select the other sequence in Main Mode, and create another
audio track (Audio 002) to go with that sequence.
39
Creating a Song
This section explains how to make a song out of your sequences. Before starting, make sure that you have recorded
some sequences (which we described earlier).
To enter Song Mode, make sure playback is stopped, and then press Menu, and then tap Song to enter Song Mode.
Alternatively, press Song (MPC X).
In Song Mode, each of the sequences you’ve created in this project assigned to a pad. The sequence playlist is to
the left of the pads, showing the song’s structure.
As a song plays, it moves through each step of the sequence playlist. Each step contains a sequence you assigned.
Each step can be repeated, determined by the value in the Repeat column (the repeat icon; a value of 1 means the
sequence will play through only once). The Bars column on the right indicates the length of that sequence.
Each step can be set to play its sequence at an independent tempo, determined by the value in the BPM column.
Important: Each sequence has its own tempo, while the project itself may use a different master tempo. The BPM value
for each sequence may be different from the master tempo. As long as playback is set to follow the master tempo, each
sequence’s individual tempo will be ignored. By default, each project is set to use the sequence tempo, which you set
back in the Creating a Drum Sequence chapter. We recommend tapping the Seq/Mst button at the top of the screen
(so the button displays Mst) and entering a master tempo to ensure all sequences use the same tempo.
To insert a step at the current position, tap Insert.
To delete the currently selected step, tap Delete.
To set which sequence plays for a step, tap the step’s Sequence field, and then turn the data dial to select a
sequence.
To set how many times a sequence repeats, tap the step’s Repeat field (next to the sequence name), and then
turn the data dial to select a number.
40
Exporting the Song
Want to share your new song? Just export it first.
To export a song:
1. While in Song Mode, tap Export at the bottom of the screen.
2. In the Audio Mixdown screen that appears, do the following:
•
Make sure the Start field is set to 1, and set the End field to the last bar of your song.
•
Tap the Audio Tail field and turn the data dial to set it to 2 seconds.
•
As you’ll likely share the song online, tap the mp3 file format option in the lower-left corner.
3. Tap Export. Choose where you want to save the song.
To name the song, tap the File Name field, and use the virtual keyboard that appears to enter a new name, and
then tap Save to start exporting.
41
Other Features Explained
This chapter describes various advanced features. For a fuller explanation of these features, please refer to their
corresponding sections in the Operation chapter.
Step Sequencer
You’ve already learned how to record note events on a track, but you can quickly enter note events in the Step
Sequencer by using the pads as “step buttons,” simulating the experience of a traditional step-sequencer-style drum
machine.
To enter the Step Sequencer, press Menu, and then tap Step Sequencer. Alternatively, in some modes, you can
tap the steps icon on the left edge of the screen. You can also press Step Seq (MPC X).
1. Let’s create a sequence on a new track. Tap the Track field in the upper-left corner, and then use the data dial or
–/+ buttons to select an (unused) track. Alternatively, double-tap the Track field, and then tap a track to select it.
2. Tap the Track Length field at the top of the screen to set a length for the track, and then use the data dial or the
–/+ buttons to select a length. If you select the minimum value, Sequence, the track will be however long your
sequence is.
Tip: This lets you maintain tracks of different lengths. For instance, you could play a 1-bar drum sequence
repeatedly under a 4-bar bass line.
3. Tap the Bar –/+ buttons at the bottom of the screen to select the bar whose steps you want to create or edit.
The bar number will appear in the Bar field in the upper-left corner.
4. Tap the Pad –/+ buttons at the bottom of the screen to select the pad whose steps want to create or edit. The
pad number will appear in the Pad field in the upper-left corner.
5. Press Play to start your sequence.
6. Each pad represents a step in the bar. If the pad already has note events on the selected track, the corresponding
pads (steps) will be lit with colors corresponding to their velocities.
To enter a note at a step, press an unlit pad. The pad will light up with a color corresponding to its velocity.
To delete the note from a step, press a lit pad. The pad will become unlit.
To delete all notes from the entire bar, press and hold Shift, and then tap Clear Bar in the lower-right corner.
See Operation > Modes > Step Sequencer to learn more about this feature.
42
Drum Loops & Chop Mode
Modern music producers often use drum loops to add grit and nuance to programmed beats. This section explains
how to use Sample Edit Mode to work with drum loops.
Use the Browser to locate a drum loop, and then double-tap it to add it to the current program. The loop does not
have to match the tempo of anything in the project.
To enter Sample Edit Mode, press Menu, and then tap Sample Edit to enter Sample Edit Mode. Alternatively,
press Sample Edit (MPC X).
1. Tap the Sample field at the top of the screen, and then use the data dial or –/+ buttons to select the loaded
drum loop. You can scroll through all loaded samples in the project. Alternatively, double-tap the Sample field,
and then tap a sample to select it.
2. Tap the Trim/Chop tab in the lower-left corner to switch between Trim Mode and Chop Mode. Select Chop
Mode, which will let us cut the drum loop into slices.
3. Tap Threshold, and then tap the Threshold field to the right of it. Use the data dial, –/+ buttons, or numeric
keypad (MPC X) to select a value. Alternatively, double-tap the Threshold field and use the numeric keypad on
the screen. The lower the threshold, the more slices will be created. Be sure to select a value so that every
transient peak of the drum loop has a corresponding a slice marker.
Tip: Each slice will be automatically assigned to a pad: Pad A01 plays Slice 1, Pad A02 plays Slice 2, etc. Press
each pad to play the slice with the same number.
43
Let’s use this chopped sample to create a new program in which each of these slices is an individual sample. We
can also automatically create corresponding note events to play back these slices sequentially.
1. Press and hold Shift and then tap Convert at the bottom of the screen to enter the Convert or Assign Slices
window.
2. Tap the Convert To field, and then use the data dial or –/+ buttons to select New Program with New Samples.
3. Make sure Crop Samples is checked. If it is not, tap it.
4. Make sure Create New Program is checked. If it is not, tap it.
5. Make sure Create Events is checked. If it is not, tap it.
6. Tap the Bars field, and then use the data dial or –/+ buttons to select how many bars the entire sample should
use in your program.
7. Tap Do It to proceed. Each slice will be assigned to a pad, and each pad will have a recorded note event in the
track. When you play that track, it will play each pad (each slice) in the original order. Press Menu and then tap
Grid View to see how the sample appears in your sequence.
8. Press Play and listen to how the drum loop matches your song tempo now.
You can also edit the note events of the drum loop slices—enter Main Mode to do this. A new track with the note
events playing their corresponding slices has been automatically created. Tap the TC/clock icon at the top of the
screen to use the Timing Correct window to quantize the note events so they fall on exact, even time intervals.
You can also rearrange the note events, thus creating a new playback order for the slices. You can also edit each
slice or sample in Program Edit Mode. You can add effects for slices or use the filter function to change the
frequency range of a selected slice. There are almost no limits to what you can do.
See Operation > Modes > Sample Edit Mode > Chop Mode to learn more about this feature.
44
Pad Muting & Track Muting
Pad Mute Mode and Track Mute Mode let you silence different pads and tracks to see what the sequence sounds
like without those samples or parts.
To enter Pad Mute Mode, press Menu, and then tap Pad Mute to enter Pad Mute Mode. Alternatively, press
Shift+Track Mute/Pad Mute (MPC X).
1. Press Play to play the sequence.
2. Tap the Program field at the top of the screen, and then use the data dial or –/+ buttons to select your drum
program. Alternatively, double-tap the Program field, and then tap a program to select it.
3. Mute a pad by pressing it once or tapping it on the screen. The muted pad will be lit red. You can mute multiple
pads at the same time.
See Operation > Modes > Pad Mute Mode to learn more about track mutes.
45
You can also mute entire tracks by using the similar Track Mute function.
To enter Track Mute Mode, press Menu, and then tap Track Mute to enter Track Mute Mode. Alternatively, press
Track Mute (MPC X).
1. Press Play to play the sequence.
2. Tap the Sequence field at the top of the screen, and then use the data dial or –/+ buttons to select the desired
sequence. Alternatively, double-tap the Sequence field, and then tap a sequence to select it.
3. Each pad is assigned to a track. Mute a track by pressing the corresponding pad or tapping it on the screen. The
pad will be lit red. You can mute multiple tracks at the same time.
Tip: To mute a track only at precise note intervals (“quantizing” your mutes, essentially), tap Time Division to set
a musical timing value. Tap the desired musical value (e.g., 1 Bar). Alternatively, use the data dial or –/+ buttons. Tap
Close to close the page. Now, when you press a pad in Track Mute Mode, the mute will occur precisely at the
beginning of the following time division (in this example, one bar). This lets you test musical combinations of
patterns—the preliminary stage to building a song structure.
See Operation > Modes > Track Mute Mode to learn more about track mutes.
46
Sampling (Recording)
This section describes recording new samples of your own, which you can use in your projects.
Important: To record any audio, you need to connect an audio source to your MPC hardware or to your computer’s
audio interface.
To open the Sampler, press Menu, and then tap Sampler to enter Sampler Mode. Alternatively, press Sampler (MPC X).
1. Connect an audio source to the input/inputs of your MPC hardware.
2. The Input ___ menu in the upper-left corner should be set to Input 1,2 (the inputs of your MPC hardware). If it is
not, then select Input 1,2.
3. Turn the 3/4 Rec Gain (MPC X) or Rec Vol (MPC Live, MPC Touch) knob to set the input level while playing your
audio source. You should now see the level in the meter. Make sure it does not exceed the maximum level (the
meter should not be “peaking” constantly).
4. Tap and drag threshold slider to set the threshold. Alternatively, use the data dial or –/+ buttons. Set it to a
fairly low level (e.g., -50 dB).
5. Tap Arm to record-arm the Sampler.
6. Play your audio source. The Sampler will start recording immediately when the input level reaches the threshold
value. Alternatively, tap the round Record button to manually start recording.
7. To stop recording, tap the round Stop button. The Keep or Discard Sample window will appear.
47
In the Keep or Discard Sample window:
To name the new sample, tap the Edit Name field and use the virtual keyboard to enter a name.
To assign the new sample to a program, tap the Program field, and then use the data dial or –/+ buttons to
select the desired program. Alternatively, double-tap the Program field, and then tap a program to select it.
To assign the sample to a pad in the program, tap the Assign to Pad field, and then press the desired pad.
Alternatively, use the data dial or –/+ buttons to select the desired pad number, or double-tap the Pad field, and
then tap a pad number.
To set the Root Note for the sample, tap the Root Note field, and then then use the data dial or –/+ buttons to
select the desired note.
To save the sample, tap the Save button at the bottom of the screen.
To play the recording, tap the Play button at the bottom of the screen.
To discard the recording and return to the previous screen, tap the Discard button at the bottom of the
screen.
To confirm your selections, tap Keep at the bottom of the screen.
To edit the sample in Sample Edit Mode, tap the Edit button at the bottom of the screen.
See Operation > Modes > Sampler to learn more about this feature.
48
Sample Editing
You may need to edit your newly recorded samples using Sample Edit Mode.
To enter Sample Edit Mode, press Menu, and then tap Sample Edit to enter Sample Edit Mode. Alternatively,
press Sample Edit (MPC X).
In Sample Edit Mode:
To switch between Trim Mode and Chop Mode, tap the Trim/Chop tab at the bottom of the screen. In this
example, use Trim Mode.
To set the sample’s start point, use the first column of Q-Link knobs (when in the Screen Q-Link Edit Mode)
to adjust the start point with varying degrees of resolution. Alternatively, tap and drag the S marker in the
waveform. You can also double-tap the Start field and use the numeric keypad on the screen to enter a value (or
tap the Start field and use the numeric keypad).
To set the sample’s end point, use the second column of Q-Link knobs (when in the Screen Q-Link Edit
Mode) to adjust the end point with varying degrees of resolution. Alternatively, tap and drag the E marker in the
waveform. You can also double-tap the Start field and use the numeric keypad on the screen to enter a value (or
tap the Start field and use the numeric keypad).
To hear your edits, press Pad 10 to play the sample from the start point to the end point.
49
Let’s apply some processing to the sample.
To open the Process Sample window, tap Process at the bottom of the screen.
1. Use the data dial or –/+ buttons to select the desired process in the Function field. Alternatively, tap Function
or double-tap the Function field, and then tap the desired process. Let’s select Pitch Shift to change the overall
pitch of your sample. This will transpose the sample without affecting its length.
2. To set the pitch shift amount, tap and drag the knob in the center of the window up or down. Alternatively, use
the data dial or –/+ buttons.
To make finer adjustments, double-tap the knob and adjust the larger version that appears. Tap anywhere else
to return to the previous screen.
3. To confirm your selections, tap Do It.
To cancel the process, tap Cancel.
See Operation > Modes > Sample Edit Mode to learn more.
50
Recording Automation with the XY Pad
Automating various parameters is a good way to add some motion and dynamism to your sequences.
1. Press Menu, and then tap XYFX to enter XYFX Mode. Alternatively, press XYFX (MPC X).
2. Double-tap the XYFX Location field, and select Program.
3. When you first enter this mode in a project, you will be prompted to “load” XYFX to the program. Tap Insert
XYFX to do this.
4. Tap Setup to show the Setup panel, which controls how the XY pad behaves.
5. Double-tap the Preset field, and tap an effect to select it. (These are just the effects available in XYFX Mode, not
all MPC effects.) Swipe up or down to view the entire list.
6. Tap and drag any of the knobs (Attack, Release, or Wet/Dry) up or down to set their values as desired. Below
them, you can see what parameter the X axis and Y axis control.
Note: XYFX uses an envelope to control how quickly the effect crossfades between the dry signal and wet signal.
The Attack knob determines how long it takes the completely dry signal to reach the wet signal (determined by
the Wet/Dry knob) after you touch the XY pad. The Release knob determines how long it takes the wet signal
(determined by the Wet/Dry knob) to return to the completely dry signal after you touch the XY pad.
7. Tap the automation button or press Read/Write (MPC X) to cycle through the available automation modes.
Make sure the button is red (the Write (W) option).
8. Press Play Start to start recording.
9. As you record, move your finger over the XY pad on the screen. The changes in the sound are being recorded as
automation of both the X axis and Y axis parameters.
Tip: While touching the XY pad, tap Latch in the lower-left corner to keep the marker on the XY pad even after
you release it. The marker will remain there until you touch another part of the XY pad or until you tap Latch again.
10. When you are done recording, press Stop.
11. Tap the automation button or press Read/Write (MPC X) to select the green Read (R) option. This ensures
your track uses the automation you just recorded when you play it back.
See Operation > Modes > XYFX Mode to learn more about using this feature.
51
Using MPC X or MPC Live as a Controller
If you are using the MPC software on your computer, you can switch MPC X or MPC Live into Controller Mode,
allowing you to use it to control the software. MPC Touch already operates as a controller only.
The MPC software offers the same features and functionality as the MPC hardware in Standalone Mode but with some
notable differences, which are discussed in Operation > General Features > Standalone vs. Controller Mode.
52
Operation
This chapter explains the complete features and functions of your MPC hardware.
Important:
•
When accessing the secondary functions of buttons on your MPC hardware, you can do this one of
two ways: (1) pressing and holding Shift and then pressing the desired button or (2) double-pressing
the desired button. This manual describes these operations using only the first option, but both are
acceptable.
•
When the left-most button at the bottom of the screen shows an upward arrow (), it means there are
additional buttons you can use when you press and hold Shift. Press and hold Shift to show the
secondary buttons, and any of them, if desired. Release Shift to return to the previous buttons.
•
Almost every mode shown on the screen has 1–6 buttons at the bottom. Each of these buttons select
a different tab in that mode or perform a specific function in that mode.
•
MPC X: You can press the F-Key button to activate or deactivate the F-Key feature. When active, the
six buttons under the touchscreen correspond to the options shown at its bottom edge. The F-Key
button and those six buttons will be lit red when active. When inactive, the six buttons under the
touchscreen will access their normal modes instead (Menu, Browser, Step Seq, Sampler, XYFX,
and Looper).
•
MPC X: As an alternative to tapping a control on the screen to select it, you can use the cursors to
navigate through the controls on the screen. The center cursor acts as an Enter key.
•
MPC Live, MPC Touch: As an alternative to double-tapping an item on the screen to “enter” it, you
can press the data dial.
•
When a parameter is highlighted and has a red outline, this means that it is selected. You can then
change it by turning the hardware’s data dial or using the –/+ buttons. If the parameter is a number,
double-tap it to show a numeric keypad on the screen to enter a specific value, or use the numeric
keypad (MPC X).
•
MPC Live, MPC Touch: When the touchscreen shows a parameter or group of parameters with a
gold outline (and sometimes a Q in the corner), this means that the current bank of Q-Link knobs
will control those parameters or settings. Turn a Q-Link knob to adjust its corresponding parameter
value or setting in that group. When the value has decimal places, you can sometimes press and hold
Shift and then turn the Q-Link knob to adjust the value by smaller increments. You can also press
the Q-Link button to select another group of four parameters.
•
Press and hold the any of the Q-Link buttons (Project, Program, Pad Scene, Pad Param, or Screen
Control/Edit: MPC X) or the Q-Link button (MPC Live, MPC Touch) to see an overview of all 16 Q-Link
knobs and their parameters in the QLinks window that appears. You can then tap a column or row of
knobs to select those four Q-Link knobs, and then release the Q-Link button. See Modes > Q-Link
Edit Mode to learn more about using the Q-Link knobs throughout your project.
53
General Features
Control Types
The MPC touchscreen uses the following types of control elements:
Knobs
To set the value for a knob, do any of the following:
•
Tap and drag the knob up or down.
•
Tap the knob to select it, and then use the data dial or –/+
buttons to adjust the value.
•
Double-tap the knob to show it in a larger screen. Alternatively,
press the center cursor or Enter (MPC X) or the data dial
(MPC Live, MPC Touch) when the knob is selected.
Tap and drag the larger version that appears, or use the data dial
or –/+ buttons to adjust the value.
If the knob is bipolar (has positive and negative values with the
center as the default position), double-tap the larger version to
reset it to the center/0 position.
Tap anywhere else to return to the previous screen.
•
Press and hold Shift while turning the data dial to adjust a value
by smaller increments.
Parameter Values
To set the value for a parameter, do either of the following:
•
Tap the field to select it, and then use the data dial or –/+ buttons
to adjust the value.
When the value has decimal places, you can sometimes press and
hold Shift and then use the data dial or –/+ buttons to adjust the
value by smaller increments.
•
Double-tap the field or hold your finger on it for a second. In the
screen that appears, use the numeric keypad, the data dial, or
the –/+ buttons to adjust the value. Alternatively, tap and drag
the value up or down.
You can also tap /2 to halve the value or x2 to double it.
To confirm the value and remain on this screen, tap Apply.
To confirm the value and return to the previous screen, tap Do It.
To return to the previous screen without changing anything,
tap the gray area in the upper-left corner of the screen.
54
Drop-Down Menus / Lists
To select an option for a drop-down menu, do any of the following:
•
Tap the field to select it, and then use the data dial or –/+ buttons to select an option.
•
Double-tap the field. In the list that appears (examples below), tap the desired option. Alternatively, use the
data dial or the –/+ buttons to select an option.
In some windows, tap the relevant button at the bottom of the screen to confirm your selection or to cancel
without changing anything.
Selectors
Selectors show all available options. One of them is always selected. The
selected option is highlighted while the others are dark.
To select an option, tap it.
55
Buttons
Buttons usually have two states: selected and deselected (active or inactive, respectively).
Some may have more than two states.
To switch between or cycle through a button’s states, do either of the following:
•
Tap it.
•
If it is outlined in red (and is not a mute button), use the data dial or –/+ buttons.
Checkboxes
Checkboxes have two states: checked and unchecked (enabled or disabled, respectively).
To check or uncheck a checkbox, tap it.
Tabs
Some modes have buttons at the bottom of the screen that let you cycle through several
similar tabs. For instance, you could view the send level that is routed to each of four
returns—each level is shown on a separate tab. With each tap, you will move to the next
tab, indicated by the squares below it.
To select a tab, tap it. Each time you tap it, it will select the next tab.
Sliders
To adjust the position of a slider, do any of the following:
•
Tap and drag the slider to the desired position.
•
Tap the desired position (this works only on some sliders).
•
Tap the slider to select it, and then use the data dial or –/+ buttons to adjust the position (this works only on
some sliders).
•
Double-tap the slider, and then tap and drag the larger version that appears, or use the data dial or –/+ buttons
to adjust the value. If the slider controls a volume level, double-tap the larger version to reset it to 0 dB. Tap
anywhere else to return to the previous screen.
56
Envelopes
To set the stages of an envelope, do either of the following:
Tip: Tap the expand-rectangle icon above the envelope to show a close-up view.
•
Tap and drag a “handle” of an envelope stage in the desired direction.
•
Set the numeric value of an envelope stage by adjusting or entering it as a parameter value
(described earlier).
The Filter/Envelope tab in Program Edit Mode.
Close-up of an AD-type filter envelope.
Close-up of an AHDS-type amp envelope.
57
Grid View Tools
In the Grid View, these four icons enable you to use different functions in the grid.
Tap one to select its mode:
Pencil: Draw Mode:
To enter a note in an empty grid square, tap the grid square.
To select a note, tap it.
To move a note, tap and drag it to another grid square.
To erase a note, double-tap it.
Eraser: Erase Mode:
To erase a note, tap it.
Select Box: Select Mode:
Note: Notes will remain selected if you switch to another mode. The selection will change, however, if you
press a pad while Hitting Pad Selects All Events is set to On.
To select a note, tap it.
To select multiple notes, tap and drag across the grid to create a box around them.
To move a note, tap and drag it to another grid square.
To move multiple notes, select them as described above, and tap and drag them.
To erase multiple notes, select them as described above, and then select the eraser tool and tap any
of the selected notes.
Magnifying Glass: Navigation Mode:
To move to another part of the grid, tap and drag it.
To zoom in or out, spread or pinch your fingers (respectively) on the grid. You can do this vertically,
horizontally, or both at the same time.
58
Audio Edit Tools
In Audio Edit Mode, these six tool icons enable you to use different functions in the waveform.
Tap one to select its mode:
Marquee: Marquee Mode:
To select a track region, tap the upper third of it.
To move a track region (or multiple selected track regions), tap and drag the upper third of it left or right.
To split the track at two specific points (creating a track region on either side and between them), tap and
drag across the middle third of it to create a translucent white box, and then tap the upper third of that box.
To shorten or lengthen a track region (or multiple selected track regions), tap and drag the lower third
of it left or right.
Arrow: Selection Mode:
To select a track region, tap it.
To select multiple track regions, tap and drag across the grid to create a box that highlights them.
Double-tap the selected track regions to deselect them.
To move a track region (or multiple selected track regions), tap and drag the upper third of it left or right.
To shorten or lengthen a track region (or multiple selected track regions), tap its edge and drag it.
Eraser: Erase Mode:
To select multiple track regions, tap and drag across the grid to create a box that highlights them.
To erase a track region (or multiple selected track regions), tap it.
Scissors: Split Mode:
To split the track at a specific point (creating a track region on either side), tap that point in the track.
To select a track region, tap its left-most edge.
To select multiple track regions, tap and drag across the grid to create a box that highlights them.
Double-tap the selected track regions to deselect them.
Mute: Mute Mode:
To select multiple track regions, tap and drag across the grid to create a box that highlights them.
Double-tap the selected track regions to deselect them.
To mute or unmute a track region (or multiple selected track regions), tap it.
Magnifying Glass: Navigation Mode:
To move to another part of the track, tap and drag it.
To zoom in or out, spread or pinch your fingers (respectively) on the grid. You can do this vertically,
horizontally, or both at the same time.
59
Programs
About Programs
Each track you create within a sequence is routed through a program. There are six
types of programs, each of which determines how the track sounds or what it is used
for. A single project can hold up to 128 programs.
This chapter covers how to create each program type.
To learn about editing your programs to your preference, see the Modes > Program
Edit Mode chapter.
A drum program uses one or more samples as its sound source. It contains (1) a list of samples and (2)
the settings for each sample (i.e., pad assignments, loop points, pitch tuning, effects, etc.). Drum
programs are used mostly for creating drum parts and quickly and easily assigning samples to pads. See
Drum Programs for more information.
A keygroup program uses one or more samples as its sound source. It contains (1) a list of samples and
(2) the settings for each sample (i.e., pitch tuning, effects, etc.). Keygroup programs are used to play
samples chromatically with a MIDI keyboard or the MPC pads. See Keygroup Programs for more
information.
A clip program uses several samples that can be looped (clips). Each clip can be assigned to a pad,
which you can press to trigger the clip according to a quantization setting. This lets you create intriguing,
layered performances by launching different combinations of clips together. See Clip Programs for more
information.
A plugin program contains an instance of a plugin through which you can send your track’s MIDI data.
See Plugin Programs for more information.
Important: For MPC X and MPC Live, plugin programs are available only in Controller Mode with the
desktop version of the MPC software. They are not available in Standalone Mode.
A MIDI program lets you send your track’s MIDI data to an external MIDI device like a synth or drum
machine. See MIDI Programs for more information.
A CV program lets you send your track’s MIDI data to an external MIDI device that uses control voltage
(CV), like a synth. See CV Programs for more information.
60
Drum Programs
A drum program uses one or more samples as its sound source. It contains (1) a list of samples and (2) the settings
for each sample (i.e., pad assignments, loop points, pitch tuning, effects, etc.). Drum programs are used mostly for
creating drum parts and quickly and easily assigning samples to pads.
To create a drum program:
1. Press Main to enter Main Mode.
2. Next to the Track field, tap the four-squares icon, which indicates a drum
program.
3. If the project does not contain a drum program yet, a new drum program
(named Program, appended with a number) will be added automatically to
the project and appear in the Program field below.
If the project already contains a drum program, the first one will be selected
automatically and appear in the Program field below.
To create another drum program, tap the + icon above the Program field.
A new drum program will be created and appended with a number (e.g.,
Program 002).
To rename the program, tap the cursor icon on the right edge of the Program
section. Use the virtual keyboard that appears to enter a new name, and then
tap Do It to confirm or the gray bar at the top of the screen to cancel.
To load a sample into a drum program:
1. Press Browse (MPC X) or Shift+Menu/Browse (MPC Live, MPC Touch) to show the Browser. Find and select a
sample, and then tap Load to load it to the program. Repeat this for any other samples you want to load into the
project. (See Modes > Browser to learn more about using the Browser specifically.)
2. Tap Sample Assign to view the pads and project’s sample pool.
3. Press or tap a pad to select it. The pad will be lit green.
4. In the Sample Pool list, tap a sample to assign it to the pad. Alternatively, use the data dial or –/+ buttons to
assign a sample and/or change the assigned sample.
To clear the assigned sample from a selected pad, tap Clear Pad.
To assign samples to additional pads, repeat Steps 3–4.
Tip: Remember that a drum program has 128 pads total—16 pads across eight banks.
61
Alternatively, assign samples in a drum program in Program Edit Mode in one of these two ways:
1. Press Menu, and then tap Program Edit to enter Program Edit Mode. Alternatively, press Prog Edit (MPC X).
2. Tap the Samples tab. This lets you view the samples assigned to all four layers of the current pad as well as
tuning and level parameters for each layer.
3. Tap a pad to select it (and play its assigned samples, if any). The pad will be lit green.
4. Tap one of the Layer fields under the sample waveform to select a layer. Tap the Sample field, and then use the
data dial or –/+ buttons to select a sample. Alternatively, double-tap the field for a layer, and then tap a sample
to select it.
1. Press Menu, and then tap Program Edit to enter Program Edit Mode. Alternatively, press Prog Edit (MPC X).
2. Tap the Pan Velocity tab. This lets you view the samples assigned to all four layers of the current pad as well as
panning and velocity ranges of each layer.
3. Tap a pad to select it (and play its assigned samples, if any). The pad will be lit green.
4. Tap one of the Layer fields to select a layer, and then use the data dial or –/+ buttons to select a sample.
Alternatively, double-tap the field for a layer, and then tap a sample to select it.
62
Keygroup Programs
A keygroup program uses one or more samples as its sound source. It contains (1) a list of samples and (2) the
settings for each sample (i.e., pitch tuning, effects, etc.). Keygroup programs are used to play samples chromatically
with a MIDI keyboard or the MPC pads.
To create a keygroup program:
1. Press Main to enter Main Mode.
2. Next to the Track field, tap the piano-keys icon, which indicates a keygroup
program.
3. If the project does not contain a keygroup program yet, a new keygroup program
(named Program, appended with a number) will be added automatically to the
project and appear in the Program field below.
If the project already contains a keygroup program, the first one will be selected
automatically and appear in the Program field below.
To create another keygroup program, tap the + icon above the Program
field. A new keygroup program will be created and appended with a number
(e.g., Program 002).
To rename the program, tap the cursor icon on the right edge of the Program
section. Use the virtual keyboard that appears to enter a new name, and then tap
Do It to confirm or the gray bar at the top of the screen to cancel.
To assign samples in a keygroup program:
1. Press Menu, and then tap Program Edit to enter Program
Edit Mode. Alternatively, press Prog Edit (MPC X).
2. Tap Samples. This lets you view the samples assigned
to all four layers of the current keygroup as well as
tuning and level parameters for each layer.
3. Tap the Number of KG field, and then use the data dial
or –/+ buttons to set the number of keygroups in the
program (1–128). Alternatively, tap the Number of KG
field, and then use the numeric keypad to enter a value (or
double-tap the Number of KG field, and then use the
numeric keypad on the screen).
4. Tap the Keygroup field, and then use the data dial or –/+
buttons to select a keygroup. Alternatively, double-tap the
Keygroup field, and then tap a keygroup to select it.
5. Tap a pad to play the sample in the keygroup. The pad
will be lit green.
Tip: On your MPC hardware, press the Pad Bank D
button to and press Pad 13. You should hear the
sample played back with its original pitch. You can use
the other pads to play your sample chromatically.
6. Tap the field for a layer, and then use the data dial or –/+ buttons to select a sample. Alternatively, double-tap
the field for a layer, and then tap a sample to select it.
To create complex keygroup programs, you can add more keygroups (up to 128). This is useful when working with
multi-samples (e.g., when programming a real piano).
Tip: Remember that a keygroup program offers up to 128 keygroups, and each keygroup can hold up to four
samples (Layers 1–4). This is a total of 512 samples.
63
Clip Programs
A clip program uses several samples that can be looped
(clips). Each clip can be assigned to a pad, which you can
press to trigger the clip according to a quantization setting.
This lets you create intriguing, layered performances by
launching different combinations of clips together.
By default, the 16 pads are divided into four columns of four
pads. Each column represents a mute group; when a pad is
playing a clip, all other pads in that same mute group are
turned off. This enables you to launch a clip without having
to manually stop other clips that are similar. For instance,
pressing Pad 2 may launch a bass clip. You could then
press Pad 6, which launches another bass clip and stops
the clip on Pad 2. This way, you’ll never be playing two bass
clips simultaneously.
The four-columns pad configuration described above is just
a default to make things easy (e.g., you could use the first
column for drum clips, the second for bass clips, the third
for keyboard clips, and the fourth for vocal clips). You can
use Program Edit Mode to assign pads to any combination
of mute groups you want.
To create a clip program:
1. Press Main to enter Main Mode.
2. Next to the Track field, tap the play-button icon, which indicates a clip program.
3. If the project does not contain a clip program yet, a new clip program (named Clip, appended with a number) will
be added automatically to the project and appear in the Program field below.
If the project already contains a clip program, it will be selected automatically and appear in the Program field
below.
To create another clip program, tap the + icon above the Program field. A new clip program will be created
and appended with a number (e.g., Clip 002).
To rename the program, tap the cursor icon on the right edge of the Program section. Use the virtual keyboard that
appears to enter a new name, and then tap Do It to confirm or the gray bar at the top of the screen to cancel.
64
To load a clip into a clip program:
1. Press Main to enter Main Mode.
2. Tap Edit Clips to view the pads and clip settings.
3. Press or tap a pad to select it (and play its assigned samples, if any). The pad on the screen will be lit red, and its
number will appear in the Pad field.
4. Tap the Sample field, and then use the data dial or –/+ buttons to select a clip. Alternatively, double-tap the
Sample field, and then tap a clip to select it.
To clear the assigned clip from a selected pad, repeat Step 4, but select None.
To assign clips to additional pads, repeat Steps 3–4.
Alternatively, assign clips in a clip program this way:
1. Press Browse (MPC X) or Shift+Menu/Browse (MPC Live, MPC Touch) to show the Browser. Find and select a
clip, and then tap Load to load it to the program. Repeat this for any other clips you want to load into the project.
(See Modes > Browser to learn more about using the Browser specifically.)
2. Tap Sample Assign to view the pads and project’s sample pool.
3. Tap Assign Mode so it is selected (tapping an item in the sample pool will now assign it automatically to the
current pad).
4. In the Sample Pool list, tap a clip to assign it to the pad. Alternatively, use the data dial or –/+ buttons to assign
a clip and/or change the assigned clip.
To clear the assigned clip from a selected pad, tap Clear Pad.
To assign clips to additional pads, repeat Steps 4–5.
65
Plugin Programs
A plugin program contains an instance of a plugin through which
you can send your track’s MIDI data. This lets you use the same
instance of a plugin with multiple tracks (rather than load an
instance of a plugin on every track, which can be cumbersome and
CPU-intensive).
To create a plugin program:
1. Press Main to enter Main Mode.
2. Next to the Track field, tap the plug icon, which indicates a plugin program.
3. If the project does not contain a plugin program yet, a new plugin program (named Plugin, appended with a
number) will be added automatically to the project and appear in the Program field below.
If the project already contains a plugin program, the first one will be selected automatically and appear in the
Program field below.
To create another plugin program, tap the + icon above the Program field. A new plugin program will be
created and appended with a number (e.g., Plugin 002).
4. Double-tap the Plugin field. In the list that appears, tap the desired plugin. Alternatively, use the data dial or the
–/+ buttons to select a plugin.
To sort your plugins by type or maker, tap Type or Manufacturer.
5. Tap Select to select the plugin, or tap Close to cancel.
Note: You have to specify the disk directory where your plugins are located. This can be done in the software’s
Preferences (in the Edit Menu). See the user guide in the MPC software to learn more: click the Help menu,
select MPC Help, and select MPC User Manual.
To select the MIDI channel the program will use, double-tap the MIDI Ch field. In the list that appears, tap the
desired channel. Alternatively, use the data dial or the –/+ buttons to select a channel. Use this setting when you
are working with a virtual instrument plugin that supports multi-mode.
To select a preset in your plugin (if any), double-tap the Preset field. In the list that appears, tap the desired
preset. Alternatively, use the data dial or the –/+ buttons to select a preset.
To rename the program, tap the cursor icon on the right edge of the Program section. Use the virtual keyboard that
appears to enter a new name, and then tap Do It to confirm or the gray bar at the top of the screen to cancel.
To adjust the volume and panning of a track using the plugin program:
1. Press Menu, and then tap Channel Mixer to enter the Channel Mixer. Alternatively, press Ch. Mixer (MPC X).
2. Double-tap the Mixer field in the upper-left corner, and then tap Midi Tracks.
3. Tap the square that represents the track with the plugin program to select it.
4. Tap and drag the volume slider or pan knob up or down to adjust it. After you do this once, you can adjust the
volume and panning of the plugin program normally.
Important:
If you copy a sequence, the volume and pan values will be copied with that sequence. This is also true if you move to
a new sequence and put the same plugin program on a new track.
By default, some plugins do not support MIDI volume and pan. In this case, adjust volume levels and panning on the
plugin program.
66
MIDI Programs
A MIDI program lets you send your track’s MIDI data to an
external MIDI device like a synth or drum machine.
To create a MIDI program:
1. Press Main to enter Main Mode.
2. Next to the Track field, tap the MIDI-jack icon, which indicates a MIDI program.
3. If the project does not contain a MIDI program yet, a new MIDI program (named Midi, appended with a number)
will be added automatically to the project and appear in the Program field below.
If the project already contains a MIDI program, it will be selected automatically and appear in the Program field
below.
To create another MIDI program, tap the + icon above the Program field. A new MIDI program will be created
and appended with a number (e.g., Midi 002).
4. There are five additional settings to configure for a MIDI program: the MIDI Port, program change message
(Program Ch), MIDI channel (MIDI Ch), Most Significant Byte (Bank MSB), and Least Significant Byte (Bank
LSB). See this section to learn more.
To configure each setting, double-tap its field. In the list that appears, tap the desired option. Alternatively, use
the data dial or the –/+ buttons to select an option.
Note: You also have to configure the MIDI ports in the software’s Preferences (in the Edit Menu). See the user
guide in the MPC software to learn more: click the Help menu, select MPC Help, and select MPC User Manual.
To rename the program, tap the cursor icon on the right edge of the Program section. Use the virtual keyboard that
appears to enter a new name, and then tap Do It to confirm or the gray bar at the top of the screen to cancel.
To adjust the volume and panning of a track using the MIDI program:
1. Press Menu, and then tap Channel Mixer to enter the Channel Mixer. Alternatively, press Ch. Mixer (MPC X).
2. Double-tap the Mixer field in the upper-left corner, and then tap Midi Tracks.
3. Tap the square that represents the track with the MIDI program to select it.
4. Tap and drag the volume slider or pan knob up or down to adjust it. After you do this once, you can adjust the
volume and panning of the MIDI program normally.
Important: If you copy a sequence, the volume and pan values will be copied with that sequence. This is also true if
you move to a new sequence and put the same MIDI program on a new track.
67
CV Programs
A CV program lets you send your control voltage (CV) signals
to an external MIDI device like a synth or drum machine that
uses CV.
To create a CV program:
1. Press Main to enter Main Mode.
2. Next to the Track field, tap the CV icon, which indicates a CV program.
3. If the project does not contain a CV program yet, a new CV program (named CV, appended with a number) will
be added automatically to the project and appear in the Program field below.
If the project already contains a CV program, it will be selected automatically and appear in the Program field
below.
To create another CV program, tap the + icon above the Program field. A new CV program will be created and
appended with a number (e.g., CV 002).
4. There are five additional settings to configure for a CV program: the note tracking (Note), the CV Port, the Gate
Port, the modulation wheel (Mod Wheel), and Velocity Port.
To rename the program, tap the cursor icon on the right edge of the Program section. Use the virtual
keyboard that appears to enter a new name, and then tap Do It to confirm or the gray bar at the top of the
screen to cancel.
68
Menu
The Menu lets you select any of the 21 modes or save your project. On MPC X or MPC Live, you can also use it to
set your preferences, switch between Standalone Mode and Controller Mode, or view your system resources.
To open the Menu, press Menu, or tap the icon in the upper-left corner of the screen while on the normal page of
your current mode.
When viewing the Menu, do any of the following:
To enter a mode, tap it.
Important: If a sequence is currently playing, you will not be able to enter Song Mode. Stop playback before
entering Song Mode.
To return to the previous mode, tap the gray area in the upper-left corner, or press Menu again.
You can also press and hold the Menu button and press a pad to select a menu mode. The pads follow the 4x4
layout of the Mode Menu.
Note: The Menu above is available when the currently selected track is a MIDI track. When an
audio track is selected, it will show an icon for Audio Edit Mode instead of Grid View.
Click a part of the screen above to skip directly to that part of this user guide.
69
Save
To save the project, tap the disk icon at the top of the screen. Alternatively, press Shift+Browse/Save (MPC X). If
you have already saved the project, your changes will be saved. If you have not saved the project yet, use the Save
window to save the project:
To select the storage device you want to view, tap it in the Storage column on the left.
Internal is the internal drive of MPC X or MPC Live.
MPC Documents is a shortcut to the MPC Documents folder on the internal drive of MPC X or MPC Live.
If you have storage devices connected to USB ports or SD card slot of MPC X, MPC Live, or your computer (with
MPC Touch), they will appear in this column, as well.
To enter a folder, double-tap it. Alternatively, turn the data dial or use the –/+ buttons to move through the list, and
press the center cursor or Enter (MPC X) or the data dial (MPC Live, MPC Touch) to enter a folder. You can also
tap one of the five folder buttons in the upper-right to jump immediately to those pre-assigned file paths (see
Modes > Browser to learn how to do this).
To create a new folder, tap New Folder, use the virtual keyboard that appears to enter a name, and then tap Do It.
You will immediately enter the new folder.
To move up one folder level, tap the folder/ icon in the upper-left corner.
To name the file, tap the File Name field at the bottom of the screen, and use the virtual keyboard that appears.
To save the file, tap Save.
To save the file as a project template file, tap the Save as Template checkbox to check it before tapping Save.
(This file will be shown in the Template File field in the Preferences’ Project Load/Save tab.)
To cancel and return to the Menu, tap Cancel. Alternatively, tap the  icon in the upper-left corner.
70
Preferences
To open the Preferences, tap the gear icon at
the top of the screen.
To return to the Menu, tap the  icon in the
upper-left corner. Changes to the Preferences are
saved automatically except for Vintage Mode (in
the General tab) and Start Time (in the Sync tab).
To restore your MPC hardware’s default
settings, tap Reset. In the screen that appears,
tap OK to continue or Cancel to return to the
Preferences. In the next window, tap Save to save
your current project before restoring the default
settings; tap Cancel to return to the Preferences;
or tap Don’t Save to restore the default settings
without saving your current project.
Important: For MPC X and MPC Live, the
Preferences will appear differently in Controller
Mode than in Standalone Mode. Some of the
options described in this section may be available in
only one of these modes or in a different order.
Info
This screen shows current information about your MPC hardware: its current firmware version, which includes its
standalone operating system (MPC Firmware); its hardware Serial Number; and its current firmware for the Control
Surface.
To view legal information relevant to MPC, tap Legal Info. For complete legal information, visit
akaipro.com/product-legal.
To enter Update Mode, press and hold Shift and tap Update. In the screen that appears, tap Save to save your
current project before entering Update Mode; tap Cancel to return to the Preferences; or tap Don’t Save to enter
Update Mode without saving your current project.
Wi-Fi
The settings on this screen will determine how your MPC hardware's wireless connection works, so you can use
Ableton Link, a new technology that synchronizes beat, phase and tempo of Ableton Live and Ableton Link-enabled
applications over a wireless or wired network. These settings are available only for MPC X and MPC Live when used
in Standalone Mode.
To activate or deactivate wireless connectivity on your MPC hardware, tap the On/Off selector. The
available wireless networks will appear in the panel below it.
To select a wireless network, tap it.
To connect to a selected wireless network, tap Connect. If the Wi-Fi network is password-protected, use the
virtual keyboard that appears to enter the correct password to connect to it.
To view the information of a selected wireless network, press and hold Shift and tap Info. The Network
Information window that appears will show the network name, IPv4/IPv6 address (including the subnet mask
and gateway), type of security, and signal strength (as a percentage).
To disconnect from a connected wireless network, tap Disconnect.
To clear the connection information (e.g., the password) from a selected wireless network, tap Forget.
71
Ethernet
The settings on this screen will determine how your MPC hardware connects to a wired network using a USB-toEthernet adapter. This allows you to maintain a tighter network connection when using Ableton Link or the Akai
Network Driver. These settings are available only for MPC X and MPC Live when used in Standalone Mode.
To activate or deactivate Ethernet connectivity on your MPC hardware, tap the Enabled box.
To determine how your MPC hardware connects to the network, use the Address Method dropdown. Select
Automatic to have your MPC hardware set the Ethernet connection, or Manual to set it yourself.
When setting the Ethernet connection manually, tap the IP Address, Subnet Mask, Gateway, and DNS fields to
input the values.
Bluetooth
The settings on this screen will determine how your MPC hardware’s Bluetooth connection works, so you can use
Bluetooth MIDI controllers (e.g., LPD8 Wireless or LPK25 Wireless) or a Bluetooth computer keyboard with it. These
settings are available only for MPC X and MPC Live when used in Standalone Mode.
To activate or deactivate Bluetooth connectivity on your MPC hardware, tap the On/Off selector. The
available Bluetooth devices will appear in the panel below it under Available Devices. The Bluetooth devices
that have already paired to your MPC hardware will appear under Paired Devices.
To select a Bluetooth device, tap it.
To pair a selected Bluetooth device (in the Available Devices section), tap Pair.
To connect to a selected Bluetooth device (in the Paired Devices section), tap Connect.
To disconnect from a connected Bluetooth device (in the Paired Devices section), tap Disconnect.
To return an available Bluetooth device to its original state, tap Remove.
Sequencer
The settings on this screen determine how sequencing works in the Grid View and in the Step Sequencer.
Display Resolution: This is the display resolution (in PPQN—pulses per quarter note) of pulse values in certain
areas of the operating system. Please note that this setting affects the display resolution, not the timing.
Instant Track Mute: When disabled, if you mute a track, its Note On messages will be ignored, and samples and
notes that are playing will finish playing their entire length (this is how legacy MPCs’ track-muting worked). This is
useful if you are using loops and want a loop to play to the end of a bar but not play the next time the sequence
loops. When enabled, if you mute a track, the MIDI track volume (0) will be sent. The loop will continue to play
but at zero volume, allowing the loop to continue playing when the track is unmuted. This is useful when you
want to have the track muted immediately.
Play Track Mute and Solo Events: When enabled, track mute and solo events are played back when you are in
Track Mute Mode. When disabled, track mute and solo events will not be played back while in Track Mute Mode.
Record Track Mute and Solo Events: When enabled, track mute and solo events are recorded when you are in
Track Mute Mode (timing correct settings will affect the recorded position events). When disabled, track mute
and solo events will not be recorded while in Track Mute Mode. This feature is useful if you want to use Track
Mute Mode to record track mutes or solos into your sequences as opposed to using Track Mute Mode for
performance or listening purposes only.
Record Pad Aftertouch Events: When enabled, pad aftertouch data (from the MPC hardware’s pressuresensitive pads) will be recorded. When disabled, pad aftertouch data will be ignored.
Place Events Recorded During Count-In at Start Point: When enabled, pressing a pad during the recording’s
pre-count will record that note event at the start of the recording (this is how the MPC3000 worked). When
disabled, no notes will be recorded until the pre-count is finished and recording has begun.
Note: This setting is ignored when recording with the Arpeggiator active.
72
Truncate Duration: This determines if/how events are cropped if they exceed the length of the current Sequence:
To Sequence Length: If the length of an event exceeds the length of the sequence, it will be truncated. This
ensures that the event will not overlap itself when the sequence loops.
To Sequence End: If an event exceeds the length of the sequence, it will be truncated to the end of the
current sequence. In other words, the event will stop playing when the sequence ends or loops.
As Played: Events will play back exactly as they were recorded, even if they overlap themselves when the
sequence loops.
Bar 1
2
3
4
5
For example, if you record a note starting on the second bar of a 4-bar loop
and hold it for 5 bars, the note would end: at bar 7 (As Played), at bar 6 (To
Sequence Length), or bar 4 (To Sequence End). See image for details.
6
7
8
As played
To Sequence Length
To Sequence End
Q-Link Swing Control Applies TC Settings on Release: When enabled, turning the Q-Link knob assigned to
Swing and then releasing it will immediately apply that Swing setting. When disabled, you must use the Timing
Correct window to apply the Swing setting.
Sync
The settings on this screen determine how your MPC hardware synchronizes with connected USB and MIDI devices.
Receive: This determines whether your MPC hardware receives MIDI Clock information (MIDI Clock), MIDI Time
Code information (MIDI Time Code (MTC)), communication from Ableton Link (Ableton Link), or none of these (Off).
Receive MMC: When enabled, your MPC hardware will be able to receive MIDI Machine Control (MMC)
information. When disabled, your MPC hardware will not receive this information. See Appendix > MIDI Machine
Control (MMC) to learn about this.
Send: This determines whether your MPC hardware sends MIDI Clock information (MIDI Clock), MIDI Time
Code information (MIDI Time Code (MTC)), or neither (Off).
Send MMC: When enabled, your MPC hardware will be able to send MIDI Machine Control (MMC) information.
When disabled, your MPC hardware will not send this information. See Appendix > MIDI Machine Control (MMC)
to learn about this.
MTC Frame Rate: This determines the frame rate used by MIDI Time Code (MTC), which is important for correct
timing, especially when working on film scoring projects. In most cases, you should select 25.
Start Time: This is the starting time that will be sent when Send MIDI is set to anything other than Off. The time
is formatted in hours:minutes:seconds:frames.
Send Port 1–4: These are the MIDI ports over which MIDI Clock or MTC information will be sent.
Hardware
The settings on this screen determine the behavior of your MPC hardware’s pads and touchscreen.
Pad Threshold: This determines how much force is required to strike the pads for them to trigger.
Pad Sensitivity: This determines how the pads respond to touch. At lower values, you need to use more force to
generate a high-velocity note. At higher values, it is easier to generate high-velocity notes, even if you do not use
much force while pressing a pad.
Pad Curve: This determines how striking the pads translates into velocity values. The A MIDI
curve is essentially linear, while the B, C, and D curves are exponential (see graphic here). Velocity
Velocity & Aftertouch: View these meters when striking and pressing the pads to help
gauge the force and pressure you are applying to them. These meters are useful when
adjusting the Pad Threshold and Pad Sensitivity parameters (above).
Footswitch 1 & Footswitch 2: These determine how connected footswitches will work.
These options are available for MPC X only, not for MPC Live or MPC Touch, which do
not have footswitch inputs.
Applied
Force
MIDI Control Mode Output: This determines which MIDI port the MPC hardware is
using to send MIDI messages to external MIDI devices.
73
Screen Dimming: This determines how much time must pass before your MPC hardware automatically dims its
touchscreen (if it uses a battery, this can help preserve battery life).
Screen Brightness: This determines the brightness of the screen during normal operation: normal brightness
(Day) or dimmed (Night).
Power On Screen (MPC Live only): This determines if/when a special screen will appear when you power on
your MPC Live. On this screen, you must tap and hold a button for a moment to begin using MPC Live or it will
automatically power off. This feature prevents it from powering on accidentally and wasting battery life. You can
set it to the following options:
Never: The screen will never appear.
When On Battery: The screen will appear only if you power on MPC Live while using battery power.
Always: The screen will always appear.
VU Meter Source (MPC X only): This determines what audio signal level is shown in the level meters (on the right side
of the screen). When set to Master, the level meters show the audio signal sent out of Outputs 1/2 (the Main L/R
outputs on the rear panel). When set to Current Program, the level meters show the audio signal of the currently
selected program (i.e., the program used by the currently selected track and any other tracks that also use it).
Date (MPC X & MPC Live only): This is the current date, formatted as Month / Day / Year. When saving files on
MPC X or MPC Live in Standalone Mode, the file will include the current date in its metadata. If you use MPC X
or MPC Live in Controller Mode, this setting will be overwritten with the current date of the host computer.
Time (MPC X & MPC Live only): This is the current time, formatted as Hour : Minute. When saving files on MPC
X or MPC Live in Standalone Mode, the file will include the current time in its metadata. If you use MPC X or
MPC Live in Controller Mode, this setting will be overwritten with the current time of the host computer.
Time Zone (MPC X & MPC Live only): This is the current time zone, formatted as Continent / City, which you can
change here.
Project Defaults
The settings on this screen determine various default values for any new project that you create.
New Project Dialog: This determines what options you see when you start a new project. When set to Off, a
new project will be empty with no preconfigured settings except for the project defaults shown here. When set to
Demo, you can choose to load a demo project (from several different genres) as a starting point or an empty
project. When set to Demo/Template/Recent, you can choose to load a demo project, a project template file, or
an empty project. You must have a project in the Template File field of the Project Load/Save tab to select a
template in this window.
Default Tempo: This is the default tempo in BPM.
Default Master Tempo: When enabled, the default tempo value will be used for the master tempo. When
disabled, the default tempo will be used for sequences.
Default Sequence Bars: This determines the default number of bars of a new sequence.
Default Time Signature Numerator: This determines the number of beats per bar of a new sequence (the top
number of a time signature).
Default Time Signature Denominator: This determines the value of each beat of a new sequence (the bottom
number of a time signature).
Default Pad Slice: This determines how new samples will play when you load them or record them into a
project. When set to Pad, the Slice menu in Program Edit Mode will be set to Pad, which lets you set the start
point, end point, etc. for the layer. When set to All, the Slice menu in Program Edit Mode will be set to All, in
which the entire sample plays.
Default Drum/Keygroup Filter: This determines the default type of filter that drum and keygroup programs will
use. See Appendix > Glossary > Filter to learn about this.
Default Plugin Synth: This determines the default instrument plugin that a new plugin program will use. Use the
window that appears to select it.
74
Project Load/Save
The settings on this screen determine if (and how) projects are automatically saved. If you are using MPC hardware
as a controller, you can also define files to load automatically.
Auto Load File: Use this field to select a project (.xpj) or program (.xpm) to load automatically anytime you open
the MPC software. (For MPC X and MPC Live, this option is available only when using your MPC hardware in
Controller Mode.)
Enabled: When enabled, your project will automatically save after each Timeout interval. When disabled, your
project will not be automatically saved; you may save only manually.
Timeout: Use this field to select how often your project will automatically save.
Template File: Use this field to select a project template that will load automatically when you select User
Template in the New Project Dialog window. (If you select the Save as Template box when saving a file, it will
be shown in this field.) In order for the User Template option to be available, New Project Dialog (in the Project
Defaults tab) must be set to Demo or Demo/Template/Recent.
Record/Export
The settings on this screen determine the settings for recording and exporting.
Recording Bit Depth: This determines the bit depth of recorded audio.
Include Program Volume/Pan Settings: When enabled, the exported audio or MIDI file will include its volume
and pan settings. When disabled, the volume and pan settings will be set to 0 dB and center (C), respectively.
Bypass Program Effects Plugins: When enabled, the exported audio or MIDI file will include any third-party
effect plugins that are used with it, but those effects will be bypassed (deactivated). When disabled, those effects
will be activated.
Audio Tail Length: This determines the length of an audio tail (silence) that will be applied to the exported audio
file. When set to 0, the audio file will not have any additional audio tail.
Audio Export: This determines what part of the sequence is exported when you click the Export Audio icon.
Track: When this is selected, Export Audio will export the currently shown track in the current sequence.
Program: When this is selected, Export Audio will export all tracks in that sequence that use the currently
shown program.
Master: When this is selected, Export Audio will export all tracks in that sequence that use programs routed
to master outputs.
MIDI Export: This determines what part of the sequence is exported when you click the Export MIDI icon.
Track: When this is selected, Export MIDI will export the currently shown track in the current sequence.
Sequence: When this is selected, Export MIDI will export all tracks in the current sequence.
Bounce Bit Depth: This determines bit depth of the audio file that is exported when you click the Export Audio
icon: 16-bit or 24-bit.
General
The settings on this screen determine how other features work in the hardware and operating system.
Tap Tempo: This determines how many times you have to press the Tap button before the new tempo is
recognized.
Flash Tap Tempo Light: When enabled, the Tap button’s light will flash in time with the tempo. When disabled,
the Tap button’s light will be off.
Filter ‘All Notes Off’ CC: When enabled, “All Notes Off” (“MIDI panic”) messages will be ignored. This is useful if
you are using an external MIDI device that can send these types of messages but you want to filter them out.
When disabled, “All Notes Off” messages will be received normally.
Program Change: This determines what an incoming MID I program change message will change: a Program,
Sequence, or Track.
75
Vintage Mode: This determines the type of emulation applied to the audio output. You can apply the particular
sonic qualities of, for example, the MPC3000 or MPC60, or of course no emulation (None).
Audition Auto Play: This determines how long a sample will sound when auto-previewing it.
Audition Outputs: This determines which pair of outputs will play any auditioned sounds (Out 1,2–7,8 in
Standalone Mode, Out 1,2–31,32 in Controller Mode; MPC Live does not use Out 7,8 in Standalone Mode but
displays them to maintain compatibility with MPC X, which does use them). These sounds include: samples,
programs, and projects in the Browser; sample playback, Cue Preview, and Slice Preview in Sample Edit
Mode; and sample playback in the Keep or Discard Sample window in the Sampler.
Cue Preview: This determines if/how audio is played as you move the cue playhead. As you move the cue
playhead through a sample waveform, you can set it to play the small part of the sample before the cue playhead
(Before), play the small part of the sample after the cue playhead (After), or not play at all (Off). You can also set
this in Sample Edit Mode (see Modes > Sample Edit Mode > Settings).
Slice Preview: This determines if/how audio is played as you move a slice marker. As you move the slice marker
through a sample waveform, you can set it to play the small part of the sample before the slice marker (Before),
play the small part of the sample after the slice marker (After), or not play at all (Off). You can also set this in
Sample Edit Mode (see Modes > Sample Edit Mode > Settings).
Threads: This determines how many cores of your computer’s processor will be used to render audio. The
available range depends on your processor. (For MPC X and MPC Live, this option is available only when using
your MPC hardware in Controller Mode.)
Audio Warp Algorithm: This determines how a sample is “warped” when you adjust the length of a sample
without changing its pitch (e.g., the Warp function in Audio Edit Mode for audio tracks or in Program Edit Mode
for clip programs). (For MPC X and MPC Live, this option is available only when using your MPC hardware in
Controller Mode.)
Note: The Warp algorithms are very CPU-intensive and can result in audio drop-outs during playback if used too
freely. Be mindful of how (and how often) you use the warp function. You can reduce the CPU resources required
by using a Warp algorithm other than Elastique Pro, which is very CPU-intensive.
Audio Track Auto Warp: This determines how recorded audio track regions are warped. When set to On, any
audio track region that you record will be warped automatically to match the current sequence tempo. You can
then adjust the sequence tempo while the audio track region remains in time.
Note: When you record an audio file, the current sequence tempo will be embedded with it. This information is
stored within the sample file when you save the project. When you warp an audio track region, the warping
algorithm uses this sequence tempo and the current value in the BPM field to generate the “stretch factor.”
BPM Detection Range: This defines the range of detectable BPM values when you use any automatic BPM
detection function in the software or when you press the Tap button to enter a new tempo.
Bank Button Press: This determines how the Pad Bank buttons work.
Select A-D: Pressing a Pad Bank button once will select the corresponding bank from Pad Banks A–D.
Pressing and holding Shift while pressing a Pad Bank button will select the corresponding bank from Pad
Banks E–H.
Select/toggle bank: Pressing a Pad Bank button will alternate between the corresponding bank from Pad
Bank A–D and Pad Bank E–H. In other words, you do not need to hold Shift to select one of Pad Banks E–H.
Desktop Screensaver Disable: This determines if/when your computer’s screensaver is disabled while using
the MPC software (i.e., using your MPC hardware in Controller Mode):
Never: Your computer’s screensaver will function normally.
When hardware used: As long as your MPC hardware is connected to your computer and being used, your
computer’s screensaver will be disabled.
When hardware attached: As long as your MPC hardware is connected to your computer and powered on,
your computer’s screensaver will be disabled. It will function normally again if you power off or disconnect
your MPC hardware from your computer.
Always: Your computer’s screensaver will be disabled as long as the MPC software is open (whether or not
your MPC hardware is connected or powered on).
(For MPC X and MPC Live, this option is available only when using your MPC hardware in Controller Mode.)
Collect Usage Statistics: This determines whether or not your usage statistics will be sent occasionally to us,
enabling us to improve the MPC experience. (For MPC X and MPC Live, this option is available only when using
your MPC hardware in Controller Mode.)
76
Splice
The settings on this screen control integration with the Splice platform. See Addenda > Updates in MPC 2.5 for
more information.
Sync
Tap the Sync field (in the center of the top of the screen) and then turn the data dial or use the –/+
buttons to set whether your MPC hardware receives MIDI Clock information (MIDI Clock), MIDI
Time Code information (MTC), communication from Ableton Link, or none of these (Off).
Alternatively, double-tap Sync and tap the desired option to select it.
This is the same setting as the Receive menu in Sync tab of your Preferences. See Preferences
> Sync for more information.
Important: Your MPC hardware must be connected to a wireless network in order to receive these
types of timing information. See Preferences > Wi-Fi to learn how to connect to a wireless network.
Note: Ableton Link is a new technology that synchronizes beat, phase and tempo of Ableton Live
and Ableton Link-enabled applications over a wireless or wired network.
Mode
Tap this icon to switch MPC X or MPC Live between Standalone Mode and Controller
Mode (MPC Touch already operates as a controller only). In the screen that appears,
select whether you want to save your current project before switching (Save), switch
without saving your project (Don’t Save), or stay in the current mode and project (Cancel).
You cannot freely switch between Standalone and Controller Modes without also closing
your current project.
See Standalone vs. Controller Mode to learn more.
77
System Resources
Tap one of these icons to show the System Resources window for MPC X or MPC Live.
The indicators in this window show current usage statistics:
Battery: If you are using MPC Live powered by its internal battery, the first indicator shows the current battery
life as a percentage. (See Battery Usage to learn more about MPC Live’s internal battery.)
CPU: The CPU indicator shows the current CPU as a percentage.
RAM Usage: The Mem indicator shows your MPC hardware’s current RAM usage.
Important: If you encounter a warning that there is not enough memory to complete an action while using your
MPC hardware, do the following to make more memory available:
Make sure all audio tracks in your project are not record-armed.
Delete samples from your project’s sample pool that were there before the warning appeared.
If you are still seeing the warning, do the following:
1. Manually undo the last action you performed before seeing the warning (you may not be able to use the
Undo button for this due to how the undo history is stored in RAM).
2. Save your project.
3. Do one of the following, and then load your saved project again.
•
 In Main Mode, tap the folder icon at the top of the screen, and then tap New at the bottom of the screen.
•
 Power your MPC hardware off and then on again.
•
 Press Menu and then tap the gear icon to open the Preferences. In the Preferences, tap Reset at the
bottom of the screen, tap OK, and then tap Restart to reset the Preferences.
•
 Enter Controller Mode and then reenter Standalone Mode.
Important: Although you can load multiple files at once, any samples you load into a project will be automatically
converted to full-quality uncompressed audio files, so they may use more storage space than they do on your
external storage device. If you are unable to load multiple files at once due to this, select fewer files and try again.
Drives: The Drives indicator shows the available storage space on any detected external storage devices or the
internal drive of MPC X or MPC Live.
To delete samples from the project (to create more free RAM space for sampling time, audio recording, etc.), tap
Purge. In the screen that appears, tap Unused Samples to delete all unused samples from the project, tap All
Samples to delete all samples from the project (from all programs, sequences, and audio or MIDI tracks), or tap
Cancel to return to the previous screen.
To close the System Resources window, tap OK, the X in the upper-right corner, or anywhere outside the window.
78
Time Counter/Locate
In most of the available modes, there is a time counter at the top of the screen. This indicates
the current playhead position.
To adjust the position, tap it, and then use the use the data dial or the –/+ buttons.
To open the Locate screen and adjust its settings, double-tap the time counter.
To close the Locate screen, tap the X in the upper-right corner or anywhere outside the
window.
To move forward or backward a step, tap the Step < or Step > button, respectively.
To move forward or backward a bar, tap the Bar << or Bar >> button, respectively.
To configure your auto record settings, use the Auto Record selector and adjacent fields:
Auto Record selector: Tap the desired option to select it:
Off: Auto recording is disabled.
Punch In: You can auto record using punch-in and punch-out markers, enabling you to record over a
specified length of time in the track. While recording, the entire sequence will play, but you will record over
only the area between the Punch In and Punch Out markers. Any part of the sequence before the Punch In
marker or after the Punch Out marker will remain untouched, even if you perform over it during recording.
Record Start: After you record-arm the track and start playback, you will start recording once the sequence
loops back to its start. This is essentially a punch-in feature for the entire track, enabling you to start playing a
record-armed track while allowing more time than the usual count-in to prepare for the actual recording to start.
Punch In: Use these fields to set the location of the Punch In marker, which is where recording will start (when
the Auto Record selector is set to Punch In).
Punch Out: Use these fields to set the location of the Punch Out marker, which is where recording will stop
(when the Auto Record selector is set to Punch In).
79
You can use this screen to set time markers, allowing you to jump automatically to precise locations in a sequence.
You can set up to six time markers.
To set a time marker, tap the time counter at the top of the screen, find the desired time, and then tap Set next to
the desired time marker. The time will appear next to that marker.
To jump to a time marker, tap the number next to it (1–6).
80
Timing Correct (TC)
The Timing Correct window contains various settings to help quantize the events in your sequence. You can
quantize note events on MIDI tracks or track regions on audio tracks (though you cannot apply all types of
quantization to audio tracks).
To open the Timing Correct settings:
In Main Mode or List Edit Mode: Tap the TC/clock icon at the top of the screen.
In the Grid View: Press and hold Shift and tap TC at the bottom of the screen.
In the Track View or the Step Sequencer: Tap TC at the bottom of the screen.
Note: The TC button in Pad Mute Mode and Track Mute Mode contain Timing Correct settings, but they do
not open this window. See Modes > Pad Mute Mode and Track Mute Mode to learn about those settings.
To apply the settings you selected to the current track, tap Do It.
To apply the settings you selected to all tracks, tap All Tracks.
To cancel and return to the previous screen, tap Close.
Use the Type selector to set how timing corrections are applied.
Start: The entire note event or audio track region will be nudged forward or backward so the start point aligns
with the closest time division marker in the grid. You can apply this to MIDI tracks or audio tracks.
End: The end points of note events will be extended or shortened to align with the closest time division marker in
the grid. The start points will remain untouched. You can apply this to MIDI tracks only.
Length: The end points of note events will be extended or shortened so that each event’s length is a multiple of
the time division, regardless of where it is in the grid. The start points will remain untouched. You can apply this
to MIDI tracks only.
Legato: The end points of note events will be extended or shortened to create a long, unbroken phrase from the
first note event’s start point to the last note event’s end point. Each note event will sustain until another note event
starts. If multiple note events start at the same time (and are not the last note events), their lengths will become
identical. Selecting Legato disables all other options in this window. You can apply this to MIDI tracks only.
Without legato applied.
With legato applied.
81
Use the Time Division selector to set the quantization value. Events will “snap” to these time divisions on the grid.
The T indicates a triplet-based value.
Alternatively, press and hold Note Repeat while in Main Mode, and then use the six buttons at the bottom of the screen.
Use the Swing field to set the amount of swing from 50% to 75%. Swing lets you “shuffle” your beats—from subtle
to extreme.
Use the Shift Timing field to shift all events by clock ticks.
Use the Window field to set how many events around a quantize value will be quantized. Any events outside this
range will not be quantized; events inside will.
Use the Strength field to set how strictly events will be quantized (i.e., shifted toward the quantize value). Lower
values move events a little bit towards the closest quantize value, resulting in a less mechanical feel than a strict
quantization (a higher value).
Use the Events selector to set the target range for the
time correction. You can apply the time correction to All
note events or to just the Selected ones.
To select note events to which to apply time correction,
either use the various tools in Grid View or press the
pad with the desired events (while Hitting Pad Selects
All Events is set to On). You must do this before
opening the Timing Correct window.
When Range is selected, you can define the locations
(From and To) as well as the pads or keys that will be
quantized.
82
Metronome (Click/Metro)
The Click/Metro window contains all settings regarding the metronome (click track).
To open the metronome settings:
In Main Mode or List Edit Mode: Tap the Metro/metronome icon at the top of the screen.
In the Grid View: Press and hold Shift and tap Click at the bottom of the screen.
In the Track View: Tap Click at the bottom of the screen.
Tap the Metro/metronome icon at the top of the screen.
Use the Count-In field to set if/when the metronome counts before recording.
Off disables the metronome pre-count.
Record enables the pre-count during recording only.
Record + Play enables pre-count in both Record and Playback Modes.
Use the Enable field to set if/when the metronome is enabled.
Off disables the metronome.
Play enables the metronome sound during playback only.
Record enables the metronome sound during recording only.
Record + Play enables the metronome to happen in both Record and Playback Modes.
Use the Rate field to select the metronome click’s time division: 1/4, 1/4T, 1/8, 1/8T, 1/16, 1/16T, 1/32 or 1/32T.
T indicates a triplet-based time division.
Use the Sound field to select the sound that you want to hear for the metronome: Sidestick 1, Sidestick 2, Clap,
Metroclick, Shake, Tambourine, or MPC Click.
Use the Volume knob to set the volume of your metronome click.
Tap the On/Off button to enable or disable the metronome.
Use the Output field to set which pair of outputs will play the metronome click: Out 1,2–7,8 in Standalone Mode, Out
1,2–31,32 in Controller Mode (MPC Live does not use Out 7,8 in Standalone Mode but displays them to maintain
compatibility with MPC X, which does use them).
83
Automation
You can set the automation for programs and audio tracks to be “written,” “read,” or disabled entirely. You can do
this globally or for individual programs and audio tracks.
Global
In several modes, there is a button in the upper-right corner that controls the global automation. When you tap this
button to change its state, it will change the automation state for all programs in the project.
This is available in Main Mode, XYFX Mode, Pad Mute Mode, the Pad Mixer, the Channel Mixer, and Q-Link Edit Mode.
Tap the global automation button to cycle through its three states:
When off, automation data will be ignored. If you have already recorded or entered automation,
tapping this will switch between Read (R) and Write (W) only, but you can override this and turn it off
by pressing and holding Shift while tapping the button.
Important: If you have already recorded automation and turn it off, the track will still use the effect
and its parameter values at the point where you turned it off.
When set to Read (R), automation data will be read but not recorded. (Think of this as a protective
feature to prevent accidental changes to your automation while recording.)
When set to Write (W), automation can be recorded and will overwrite any existing automation. (Make
sure not to touch the XY pad accidentally while you are recording.)
Programs & Audio Tracks
You can also set the automation for each program or audio track by using the program automation button in the
channel strip on the left side of the screen in Main Mode and the Channel Mixer. Program automation is available for
all program types except MIDI programs.
Note: Remember that tapping the global automation button will change the automation state for all programs in the
project; if they were originally different, all of them will then match the global automation state.
In Main Mode, if the channel strip is not already shown, tap the small eye icon below the Project field to show it.
In the Channel Mixer, if you do not see a program automation button in the channel strip, make sure the Mixer field
is set to Audio Tracks or Programs.
Tap the program automation button or press Read/Write (MPC X) to cycle through its three states:
When off, the program will ignore automation data. If you have already recorded or entered
automation, tapping this will switch between Read (R) and Write (W) only, but you can override
this and turn it off by pressing and holding Shift while pressing or tapping the button.
Important: If you have already recorded automation and turn it off, the track will still use the effect
and its parameter values at the point where you turned it off.
When set to Read (R), the program will read automation data but will not record any additional
automation over it. (Think of this as a protective feature to prevent accidental changes to your
automation while recording.)
When set to Write (W), the program can record automation. (If you have any Q-Link knobs assigned
to automatable parameters, make sure not to touch any accidentally while you are recording.)
84
16 Level
Press the 16 Level button on your MPC hardware to activate or deactivate 16 Level.
When first activated, the selected pad (Pad A01 by default) will be temporarily copied to all 16 pads. The pads will now
output the same note number as the initial pad, but a selectable parameter will be fixed at values that increase as the
pad numbers increase (e.g., Pad 1 is the minimum, Pad 16 is the maximum), regardless of how hard you press them.
In the 16 Levels screen that appears, use the Type selector to choose the parameter: Velocity, Tune, Filter, Layer,
Attack, or Decay.
To select a pad, do any of the following (while the 16 Levels window is open):
•
Press and hold 16 Level, and then press the desired pad.
•
Tap the 16 Levels checkbox to uncheck it (temporarily disabling the feature), press the desired pad, and
then tap the 16 Levels checkbox again to check it.
•
Tap the Pad field, and use the data dial or –/+ buttons.
•
Double-tap the Pad field, and tap the desired pad in the list that appears.
If Type is set to Tune, use the Original Pad field to select which you pad you want to use the original pitch of the
sample/samples. Alternatively, hold Shift and press the desired pad.
When Type is set to Layer, pads with multiple samples will play back each layer according to the Velocity Start and
Velocity End settings for each layer.
85
Erase
The Erase function erases all or part of a track in a specific sequence.
To open the Erase window, press the Erase button. Alternatively, while in Main Mode, tap the pencil icon on the
right edge of the section, and then tap Erase in the screen that appears.
To select the sequence you want to erase, use the Sequence field.
To select the track you want to erase within the sequence, use the Track field.
To set the time range of the sequence you want to erase, use the Bar, Beat, and Tick fields. The left fields set
the start of the time range, and the right fields set the end of the time range.
To select what types of events you erase, select one of the Erase options:
All erases all pad events from the designated time range and reset all of its settings.
Automation erases only automation from the designated time range. Use the Parameter field to select what
type of automation is erased.
Note erases only specific pad events from the designated time range. In the diagram of the eight pad banks that
appears, press each pad in each bank to select or deselect its notes.
Except Note erases everything except pad events from the designated time range.
To confirm your choice, tap Do It.
To cancel and return to the previous screen, tap the X, Cancel, or anywhere outside the window.
86
Effects
You can apply various effects to the pads, keygroups, audio tracks, programs, submixes, and master outputs, using
insert and send/return effects. This chapter can help you get a good overall understanding of how the effects work.
See Appendix > Effects & Parameters for a list of all available effects (with a brief description of each) and their
editable parameters.
Overview
In a program, each pad or keygroup can have up to four insert effects applied to it. See Insert Effects > Pads or
Keygroups to learn more about this.
An entire program or audio track can also have up to four insert effects applied to it, as well. See Insert Effects >
Programs or Audio Tracks to learn more about this.
For even further flexibility, each submix can have up to four insert effects applied to it. You can route pads,
keygroups, audio tracks, or programs to a submix, which is then routed to a master output. See Insert Effects >
Submixes to learn more about this.
Additionally, each pad, keygroup, audio track, program, and submix can each be sent to (up to) four return
channels, each of which can have up to four insert effects of their own. Their audio will be routed through the insert
effects on those returns, and the processed audio will be sent to a master output. See Send/Return Effects to learn
more about this.
Finally, you can apply up to four insert effects to each master output (a stereo pair of channels: Outputs 1/2,
Outputs 3/4, etc.). See Insert Effects > Masters to learn more about this.
When you create an audio mixdown of a sequence or song, you can choose whether or not master insert effects are
included or send/return effects are included, depending on what you are mixing down:
If you are creating an audio mixdown of a pair of master outputs, you can choose whether or not master insert
effects will be included in the mixdown.
If you are creating an audio mixdown of separate programs or exploded tracks, you can choose whether or
not send/return effects will be included in the mixdown.
See Audio Mixdown to learn about these options.
There are three other modes that handle effects differently:
•
The Sampler can use up to four insert effects, which are applied to the audio as you record it. This means
that the effects cannot be “removed” from the sound later. Learn more about the Sampler in the Modes >
Sampler chapter.
•
Similarly, the Looper can use up to four insert effects, which are applied to the audio as you record it. This
means that the effects cannot be “removed” from the sound later. Learn more about the Looper in the
Modes > Looper chapter.
•
In XYFX Mode, the effects act like a single insert effect on that program. In fact, XYFX is the name of the
insert effect you have to load to the program before you can use this mode. Learn more about XYFX Mode in
the Modes > XYFX Mode chapter.
87
To view, load, edit, or clear effects, tap the area under
the Inserts field. This usually appears in a channel strip
(next to a level slider and pan knob).
When viewing loaded effects, you will see this window:
To select an effect, use the field for each insert slot. A
window (described below) will appear.
To edit the parameters of a loaded effect, tap the
pencil icon next to the insert slot.
To clear the insert slot, tap the trash can icon next to it.
To enable or disable an effect slot, tap the On/Off
button next to it.
To disable all four effect slots, tap the All On/All Off
button in the upper-right corner. Tap it again to
reactivate the previously active effects.
When selecting an effect, you will see this window:
To move through the list, swipe up or down. Alternatively,
use the data dial or –/+ buttons.
To sort or unsort the effects by type or manufacturer,
tap Type or Manufacturer in the lower-left corner.
To load an effect, double-tap it. Alternatively, tap
Select, or press the center cursor or Enter (MPC X) or
the data dial (MPC Live, MPC Touch).
To cancel, tap Close or anywhere outside the list.
When you edit an effect, you will see this window:
To adjust a parameter, tap and drag its slider.
Alternatively, use the data dial or –/+ buttons. To
make finer adjustments, double-tap the pad and
adjust the larger version of the slider that appears.
Tip: Turn the Q-Link knobs to quickly adjust the
corresponding four parameters.
To select an effect preset, use the dropdown menu at
the top of the screen.
To load a saved preset, tap the folder icon at the top
of the screen.
To save a preset, tap the disk icon at the top of the
screen.
To select another page of parameters, tap the
Parameters –/+ buttons at the top of the screen.
To enable or disable the effect, tap the On/Off
button in the upper-right corner.
To edit parameters for another insert effect on the
same pad, program, etc., tap a different Insert tab at
the bottom of the screen to select it.
To close the window, tap Close or the upper part of
the screen.
88
Insert Effects
Pads
You can load up to four insert effects to each pad. You can do this in Main Mode, the Pad Mixer, or Program Edit Mode.
Tip: When using pad insert effects, they will be applied to the selected pad only. This means that you could apply
unique combinations of effects to each pad within a program. If you want to apply the same effect to all pads, do this
with a program insert effect (see Insert Effects > Programs).
To load a pad insert effect in Main Mode:
1. When the MIDI tab is selected (in the lower-left corner), use the Track field to select the track that uses the
program with the desired pad—the program it uses will be selected automatically.
2. If the channel strip is not already shown, tap the small eye icon below the Project field to show it.
3. Tap the single-pad icon at the top of the channel strip. The channel strip will now show settings for the current pad.
4. Press the desired pad to select it. Alternatively, use the Pad field at the top of the channel strip.
5. Tap the area under Inserts, and then use the screen that appears to load or edit effects.
89
To load a pad insert effect in the Pad Mixer:
1. Use the Program field at the top of the screen to select the desired program. Alternatively, use the Track field at
the top of the screen to select the desired track—the program it uses will be selected automatically.
2. Press the desired pad to select it, or tap it on the screen. Alternatively, double-tap the Pad field below the
Program field.
3. Tap the area under Inserts, and then use the screen that appears to load or edit effects. Alternatively, tap the Insert
tab at the bottom of the screen (tap it multiple times to select a different insert slot), and then double-tap the desired
pad on the screen. You could also use the data dial or –/+ buttons to select an effect immediately.
To load a pad insert effect in Program Edit Mode:
1. While using the desired program, press the desired pad to select it.
2. Tap the Effects tab in the lower-right corner, and use it to load or edit effects.
90
Keygroups
You can load up to four insert effects to each keygroup. You can do this in Main Mode, the Pad Mixer, or Program
Edit Mode.
Important: When using keygroup insert effects, they will be applied to that keygroup only. Keep this in mind if you
load insert effects to multiple keygroups with overlapping note ranges—the effects will overlap in that range as well.
To load a keygroup insert effect in Main Mode:
1. When the MIDI tab is selected (in the lower-left corner), use the Track field to select the track that uses the
program with the desired pad—the program it uses will be selected automatically.
2. If the channel strip is not already shown, tap the small eye icon below the Project field to show it.
3. Tap the single-pad icon at the top of the channel strip. The channel strip will now show settings for the current
keygroup.
4. Press a pad to select its corresponding keygroup, or tap it on the screen. Alternatively, use the Keygroup field at
the top of the channel strip.
Important: Remember that the effect will be applied to that keygroup only.
5. Tap the area under Inserts, and then use the screen that appears to load or edit effects.
91
To load a keygroup insert effect in the Pad Mixer:
1. Use the Program field at the top of the screen to select the desired program. Alternatively, use the Track field at
the top of the screen to select the desired track—the program it uses will be selected automatically.
2. Press a pad to select its corresponding keygroup, or tap it on the screen. Alternatively, use the Keygroup field
below the Program field.
Important: Remember that the effect will be applied to that keygroup only.
3. Tap the area under Inserts, and then use the screen that appears to load or edit effects. Alternatively, double-tap
the desired pad on the screen. You could also select one of the four Insert tabs at the bottom of the screen, and
then use the data dial or –/+ buttons to select an effect immediately.
To load a keygroup insert effect in Program Edit Mode:
1. While using the desired program, press the desired pad to select its keygroup. Alternatively, use the Keygroup
field at the top of the screen.
2. Tap the Effects tab in the lower-right corner, and use it to load or edit effects.
92
Audio Tracks
You can load up to four insert effects to each audio track. You can do this in Main Mode and the Channel Mixer.
To load an audio track insert effect in Main Mode:
1. When the Audio tab is selected (in the lower-left corner), use the Track field to select the audio track.
2. If the channel strip is not already shown, tap the small eye icon below the Project field to show it.
3. Tap the waveform icon at the top of the channel strip. The channel strip will now show settings for the current
audio track.
4. Tap the area under Inserts, and then use the screen that appears to load or edit effects.
To load an audio track insert effect in the Channel Mixer:
1. Use the Mixer field in the upper-left corner to select Audio Tracks.
2. In the touchscreen, tap the pad that corresponds to the desired audio track.
3. Tap the area under Inserts, and then use the screen that appears to load or edit effects. Alternatively, tap the Insert
tab at the bottom of the screen (tap it multiple times to select a different insert slot), and then double-tap the desired
pad on the screen. You could also use the data dial or –/+ buttons to select an effect immediately.
93
Programs
You can load up to four insert effects to each program. You can do this in Main Mode, XYFX Mode, and the Channel
Mixer.
Note: In XYFX Mode, the effects act like a single insert effect on that program. In fact, XYFX is the name of the insert
effect that is loaded when use this mode.
To load a program insert effect in Main Mode:
1. When the MIDI tab is selected (in the lower-left corner), use the Track field to select the track that uses the
program with the desired pad—the program it uses will be selected automatically.
2. If the channel strip is not already shown, tap the small eye icon below the Project field to show it.
3. Tap the four-pads icon at the top of the channel strip. The channel strip will now show settings for the current
program.
4. Tap the area under Inserts, and then use the screen that appears to load or edit effects.
94
To load XYFX for a program in XYFX Mode:
1. Select the desired program in another mode, and then enter XYFX Mode.
2. If you have not yet used XYFX Mode for this program, tap Insert XYFX on the screen to load it and show the XY
pad.
Note: If you already have four insert effects loaded, you will need to clear one of the insert effect slots before
doing this.
If you have already used XYFX Mode for this program, the XY pad will appear.
3. Tap XYFX Location in the upper-left corner, and select Program.
4. If the Setup panel is not shown, tap Setup in the lower-right corner to show it.
5. Use the Preset field to load an effect. Use the controls below the Preset field to edit the effect.
To load a program insert effect in the Channel Mixer:
1. Use the Mixer field in the upper-left corner to select Programs.
2. In the touchscreen, tap the pad that corresponds to the desired program. Alternatively, double-tap the Program
field below the Mixer field and tap the desired program.
3. Tap the area under Inserts, and then use the screen that appears to load or edit effects. Alternatively, tap the Insert
tab at the bottom of the screen (tap it multiple times to select a different insert slot), and then double-tap the desired
pad on the screen. You could also use the data dial or –/+ buttons to select an effect immediately.
95
Submixes
You can load up to four insert effects to each submix. You can do this in the Channel Mixer only.
To load a submix insert effect:
1. Use the Mixer field in the upper-left corner to select Submixes.
2. In the touchscreen, tap the pad that corresponds to the desired program. Alternatively, double-tap the Submix
field below the Mixer field and tap the desired program.
3. Tap the area under Inserts, and then use the screen that appears to load or edit effects. Alternatively, tap the Insert
tab at the bottom of the screen (tap it multiple times to select a different insert slot), and then double-tap the desired
pad on the screen. You could also use the data dial or –/+ buttons to select an effect immediately.
96
Masters
You can load up to four insert effects to each master output (a stereo pair of channels: Outputs 1/2, Outputs 3/4,
etc.). You can do this in Main Mode or the Channel Mixer.
To load a master insert effect in Main Mode:
1. If the channel strip is not already shown, tap the small eye icon below the Project field to show it.
2. Tap the crown icon at the top of the channel strip. The channel strip will now show settings for the current
master output.
3. Use the Outputs field at the top of the channel strip to select the desired master output (Outputs 1/2, Outputs
3/4, etc.).
4. Tap the area under Inserts, and then use the screen that appears to load or edit effects.
To load a master insert effect in the Channel Mixer:
1. Use the Mixer field in the upper-left corner to select Masters.
2. In the touchscreen, tap the pad that corresponds to the desired master output (Outputs 1/2, Outputs 3/4, etc.).
Alternatively, double-tap the Outputs field below the Mixer field.
3. Tap the area under Inserts, and then use the screen that appears to load or edit effects. Alternatively, tap the Insert
tab at the bottom of the screen (tap it multiple times to select a different insert slot), and then double-tap the desired
pad on the screen. You could also use the data dial or –/+ buttons to select an effect immediately.
97
Send/Return Effects
Send/return effects work in the following way:
1. A pad, keygroup, audio track, program, or submix sends its audio to a return at a designated send level.
2. That audio is processed by the effects on the return. Each return can have up to four insert effects loaded and
activated.
3. The processed audio is sent to a pair of master outputs (stereo) or a single master output (mono).
You can load send/return effects and set return levels only in the Channel Mixer, described below. The rest of this
section describes the different ways to set the desired send levels for pads, keygroups, programs, or submixes.
To load a send/return effect to a return:
1. In the Channel Mixer, use the Mixer field in the upper-left corner to select Returns.
2. In the touchscreen, tap the pad that corresponds to the desired return. Alternatively, double-tap the Return field
below the Mixer field.
3. Tap the area under Inserts, and then use the screen that appears to load or edit effects. Alternatively, tap the Insert
tab at the bottom of the screen (tap it multiple times to select a different insert slot), and then double-tap the desired
pad on the screen. You could also use the data dial or –/+ buttons to select an effect immediately.
To set the return level:
1. In the Channel Mixer, use the Mixer field in the upper-left corner to select Returns.
2. Tap the Level tab in the lower-left corner.
3. In the touchscreen, tap the pad that corresponds to the desired return. Alternatively, double-tap the Return field
below the Mixer field.
4. To adjust the level of the currently selected return, use the data dial or –/+ buttons. Alternatively, use the
level slider in the channel strip, or turn the corresponding Q-Link knob. To make finer adjustments, doubletap the pad on the screen and adjust the larger version of the slider that appears.
98
Pads
You can set the send levels for pads in Program Edit Mode or the Pad Mixer.
To set the send levels for a pad in Program Edit Mode:
1. While editing the desired program in Program Edit Mode, press the desired pad to select it.
2. Tap the Effects tab in the lower-right corner.
3. Use the Send knobs to set the send level for each return.
To set the send levels for a pad in the Pad Mixer:
1. Use the Program field at the top of the screen to select the desired program. Alternatively, use the Track field at
the top of the screen to select the desired track—the program it uses will be selected automatically.
2. Tap the Send tab at the bottom of the screen (tap it multiple times to select a different send level).
3. Press the desired pad to select it, or tap it on the screen. Alternatively, double-tap the Pad field below the
Program field.
4. To set the send level, use the data dial or –/+ buttons. To make finer adjustments, double-tap the pad on the
screen and adjust the larger version of the slider that appears.
99
Keygroups
You can set the send levels for keygroups in Program Edit Mode or the Pad Mixer.
To set the send levels for a keygroup in Program Edit Mode:
1. While using the desired program, press the desired pad to select its keygroup. Alternatively, use the Keygroup
field at the top of the screen.
2. Tap the Effects tab in the lower-right corner.
3. Use the Send knobs to set the send level for each return.
To set the send levels for a keygroup in the Pad Mixer:
1. Use the Program field at the top of the screen to select the desired program. Alternatively, use the Track field at
the top of the screen to select the desired track—the program it uses will be selected automatically.
2. Tap the Send tab at the bottom of the screen (tap it multiple times to select a different send level).
3. Press the desired pad to select its corresponding keygroup, or tap it on the screen. Alternatively, double-tap the
Keygroup field below the Program field.
4. To set the send level, use the data dial or –/+ buttons. To make finer adjustments, double-tap the pad on the
screen and adjust the larger version of the slider that appears.
100
Audio Tracks
You can set the send levels for audio tracks in the Channel Mixer only.
To set the send levels for an audio track:
1. In the Channel Mixer, use the Mixer field in the upper-left corner to select Audio Tracks.
2. Tap the Send tab at the bottom of the screen (tap it multiple times to select a different send level).
3. In the touchscreen, tap the pad that corresponds to the desired audio track. Alternatively, double-tap the Audio
Track field below the Mixer field.
4. To set the send level, use the data dial or –/+ buttons. To make finer adjustments, double-tap the pad on the
screen and adjust the larger version of the slider that appears.
Programs
You can set the send levels for programs in the Channel Mixer only.
To set the send levels for a program:
1. In the Channel Mixer, use the Mixer field in the upper-left corner to select Programs.
2. Tap the Send tab at the bottom of the screen (tap it multiple times to select a different send level).
3. In the touchscreen, tap the pad that corresponds to the desired program. Alternatively, double-tap the Program
field below the Mixer field.
4. To set the send level, use the data dial or –/+ buttons. To make finer adjustments, double-tap the pad on the
screen and adjust the larger version of the slider that appears.
101
Submixes
You can set the send levels for submixes in the Channel Mixer only.
To set the send levels for a submix:
1. In the Channel Mixer, use the Mixer field in the upper-left corner to select Submixes.
2. Tap the Send tab at the bottom of the screen (tap it multiple times to select a different send level).
3. In the touchscreen, tap the pad that corresponds to the desired submix. Alternatively, double-tap the Submix
field below the Mixer field.
4. To set the send level, use the data dial or –/+ buttons. To make finer adjustments, double-tap the pad on the
screen and adjust the larger version of the slider that appears.
102
Audio Mixdown
The Audio Mixdown screen lets you render and export either the current sequence or song as an audio file. In Song
Mode, this will export the entire song. In Main Mode, this will export the current sequence only.
To open the Audio Mixdown screen in Song Mode, tap Export at the bottom edge of the screen.
To open the Audio Mixdown screen in Main Mode, tap the Project field in the upper-left corner of the screen, and
then tap Export.
Audio Length
Use the Start Bar and End Bar fields to define where the resulting audio file will start and end, respectively.
Use the Audio Tail field to add extra seconds to the end of the resulting audio file. This is useful if you are using
effects or samples whose sounds exceed the defined audio length (e.g., long reverb or delay, one-shot samples with
long decays, etc.). We recommend using an audio tail of at least a couple of seconds.
Render Source
Check Stereo Output and use the adjacent field to select a pair of outputs (Out 1,2–7,8 and Submix 1–8 in
Standalone Mode, or Out 1,2–31,32 in Controller Mode; MPC Live does not use Out 7,8 in Standalone Mode but
displays them to maintain compatibility with MPC X, which does use them). The mixdown will be taken from these
outputs.
Check Separate Programs to create a mixdown of each program used in the sequence or song.
Check Explode Tracks to create a mixdown of each track used in the sequence (you cannot use this option for an
entire song).
Important: Each pad or keygroup must have their output routed to Program to be included in the mixdown. This is
the typical (and default) setting. See Modes > Pad Mixer > Routing to learn about this.
Render Options
If your Render Source is set to Stereo Output, check Master Inserts to include master insert effects in the mixdown.
If your Render Source is set to Separate Programs or Explode Tracks, check Export Returns to export the return
channel signals as separate files.
If your Render Source is set to Stereo Output, tap Save as Project Preview to save the sequence or song as a
project preview file (which you can play for reference in the Browser). If you check this box, Stereo Output will
automatically be checked, as well.
103
File Formats
Tap WAV, AIFF, MP3, FLAC or OGG to select the
file format of the mixdown.
For WAV and AIFF files, use the Bit Depth field to
select a bit depth of 8, 16, or 24 bits, or 32 bits,
floating point (32 F). For FLAC files, you can select
a bit depth of 16 or 24 bits. For MP3 and OGG
files, you can select a Bitrate of 128, 160, 192, or
320 kbps.
Use the Sample Rate field to select a sample rate
of 44.1 kHz, 48 kHz, 88.2 kHz, or 96 kHz. In most
cases, we recommend selecting 44.1 kHz.
Tap Export to enter the Save screen where you can select a name and location to save your audio mixdown.
Tap Cancel or the  icon in the upper-left corner to return to the previous screen.
Battery Usage
Important: Only MPC Live may use battery power. MPC X and MPC Touch must be connected to a power outlet.
Although you can power MPC Live from a power outlet (using the included power adapter), you can use its
internal battery, which typically has four hours of life, depending on CPU and how you’re using MPC Live.
While powering MPC Live from its internal battery, the battery icon in upper-right corner of the touchscreen
will show its current battery life. (The icon below it indicates whether MPC Live is in Standalone Mode or
Controller Mode.)
To view MPC Live’s system resources (battery life, CPU,
and RAM usage), tap the battery icon in upper-right
corner of the touchscreen. The System Resources window
will appear, showing percentages to indicate the current
battery life, CPU, RAM usage (Mem), and storage device
space usage.
See System Resources to learn more about the information
shown in this window.
To charge MPC Live’s internal battery, connect its power
input to a power outlet using the included power adapter.
The charging indicator light (behind the vent on the rear
panel) will turn on while charging. When the battery is fully
charged or when it is disconnected from a power outlet,
then this light will turn off.
104
Standalone vs. Controller Mode
MPC X and MPC Live can function in two ways: Standalone Mode and Controller Mode. (MPC Touch already operates
as a controller only.)
To enter Standalone Mode, do one of the following:
•
If MPC X or MPC Live is not connected to a
computer, simply press the power switch to
power it on.
•
If MPC X or MPC Live is connected to your
computer and you want to keep your MPC
software open, press Menu to enter the Menu, and
then tap the monitor/cable icon in the upper-right
corner. When the Switch to Standalone Mode
window appears, tap Standalone to continue.
Your project will remain open on your computer,
and you can continue to work on it independently
from the project shown on the screen. (If you tap
Cancel, you can continue using your MPC
hardware in Controller Mode.)
•
If MPC X or MPC Live is connected to your
computer and you want to close the MPC software,
simply close the MPC software on your computer.
When Looking for computer appears on your
MPC hardware’s touchscreen, tap Standalone. If
the Restart as Standalone window appears, tap
Yes to continue. (If you tap Cancel, you can reopen
your MPC software and continue using your MPC
hardware in Controller Mode.)
In Standalone Mode:
•
An MPC chip icon will appear in the upper-right
corner.
•
The MPC hardware is not communicating with a
computer over a USB connection.
•
Any files (projects, samples, etc.) that you save or
load are in the internal hard drive on your MPC X or
MPC Live or a connected USB drive or SD card.
•
Plugin programs are disabled.
105
To enter Controller Mode:
1. Make sure the USB-B Port on your MPC X or MPC
Live is connected to your computer.
2. On your computer, open the MPC software.
3. If MPC X or MPC Live is powered off, press the power
switch to power it on.
4. If MPC X or MPC Live is currently in Standalone Mode,
press Menu to enter the Menu, and then tap the MPC
chip icon in the upper-right corner. When the Enter
Controller Mode window appears, tap Controller
Mode to continue. (If you tap Cancel, you can continue
using your MPC hardware in Standalone Mode.)
Looking for computer may appear briefly on the
screen before the MPC hardware recognizes the USB
connection as a controller.
In Controller Mode:
•
A monitor/cable icon will appear in the upperright corner.
•
The MPC hardware is communicating with a
computer over a USB connection.
•
You can save or load files (projects, samples, etc.)
to or from your computer as well as the internal
hard drive on your MPC X or MPC Live or a
connected USB drive or SD card.
•
Plugin programs are enabled. Remember to specify
the disk directory where your plugins are located.
This can be done in the software’s Preferences (in
the Edit Menu). See the user guide in the MPC
software to learn more: click the Help menu, select
MPC Help, and select MPC User Manual.
•
The touchscreen on your MPC hardware reflects
what it is controlling in the software, but due to
space and character limitations, the layout on the
screen is different (e.g., parameter names may be
abbreviated, the layout may be different or spread
across multiple tabs, etc.).
106
Modes
The MPC hardware has a Menu page that lets you select any one of several modes. This chapter describes the
various features and functions of each one.
Click a button below to skip directly to that chapter.
Note: The Menu above is available when the currently selected track is a MIDI track. When an
audio track is selected, it will show an icon for Audio Edit Mode instead of Grid View.
While in Main Mode, the Grid View, Audio Edit Mode, the Track View, the Step Sequencer,
or XYFX Mode, the left edge contains icons to quickly enter one of five modes. Using this strip
of icons, you can easily jump between them:
To enter Main Mode, tap the house icon.
To enter the Grid View, tap the grid icon. The MIDI tab in the lower-left corner of the
screen in Main Mode must be selected for this icon to be shown.
To enter Audio Edit Mode, tap the waveform-and-box icon. This Audio tab in the
lower-left corner of the screen in Main Mode must be selected for this icon to be shown.
To enter the Track View, tap the bars-and-magnifying-glass icon.
To enter the Step Sequencer, tap the vertical-bars icon.
To enter XYFX Mode, tap the XY icon.
107
Main Mode
Main Mode gives you an overview of the most-used functions.
To enter Main Mode, do one of the following:
•
Press Main.
•
Press Menu, and then tap Main.
The top of the screen shows the project name and timing information.
The Project field shows the name of the current project.
To view the Project window, tap the Project field. The Project window will appear, showing a list of available
programs, sequences, and samples in the project.
In the Project window, in additional to typical functions you can perform in lists, you can do any of the following:
To move through a list, swipe up or down.
To expand or collapse the list of programs or sequences, tap the arrow (∨ or >) to its left.
To select a program, sequence, or sample, tap it.
To immediately select a sample and enter Sample Edit Mode, double-tap it.
To save the project, tap Save.
To save the project with another name, tap Save As. Use the Save window that appears to save the project.
To return to the previous screen, tap the X in the upper-right corner or anywhere outside the window.
To delete samples from the project (to create more free RAM space for sampling time, audio recording, etc.),
tap Purge. In the screen that appears, tap Unused Samples to delete all unused samples from the project, tap
All Samples to delete all samples from the project (from all programs, sequences, and audio or MIDI tracks), or
tap Cancel to return to the previous screen.
To export the current sequence, tap Export. Use the Audio Mixdown screen that appears to export a song
(see General Features > Audio Mixdown to learn about the settings in this window). To export the song
instead, see the Song Mode chapter.
To export the current sequence as an Ableton Live Set, tap ALS Export. See Appendix > Updates in v2.6 >
New Features > Ableton Live Set Export for more information.
108
The In and Out boxes indicate your MPC hardware is receiving or sending (respectively) MIDI messages from or to
your computer.
The time counter at the top of the screen the current playhead position. This is shown in most of the modes. See
General Features > Time Counter/Locate to learn about this.
The TC icon opens the Timing Correct window, which contains various settings to help quantize the note events in
your sequence. See General Features > Timing Correct (TC) to learn about this.
The Metro/metronome icon opens the Click/Metro menu, which contains all settings regarding the metronome
(click track). See General Features > Metronome (Click/Metro) to learn about this.
The automation button indicates the global automation state. This is shown in several modes. See General Features
> Automation to learn about this.
In Main Mode, these are the buttons at the bottom of the screen:
MIDI: Tap this button to view only MIDI tracks in the Track section.
Audio: Tap this button to view only audio tracks in the Track section.
Track –/+: Tap one of these buttons to switch to the previous or next track, respectively.
Mute: Tap this button to mute the current track.
Solo: Tap this button to solo the current track.
109
On the left edge of the screen, next to the five mode icons, there are two small icons
that control the channel strip.
To show or hide the channel strip, tap the eye icon.
The icon below the eye icon indicates the type of channel strip (see next description).
The channel strip contains some important settings for the current pad, program,
track, or master output, depending on the currently selected icon:
To view the pad channel strip, tap the single-pad icon.
To view the program channel strip, tap the four-squares icon.
To view the track channel strip, tap the bars icon (when the MIDI tab is
selected) or the waveform icon (when the Audio tab is selected).
To view the master channel strip, tap the crown icon.
When viewing the pad channel strip while using a drum program, keygroup program,
or clip program:
The first field shows the current pad number. Press a pad or tap the field to select
a different pad.
Tip: This is useful for mixing your pads without having to enter the Pad Mixer.
The second field shows where the pad is routed, which you can change: Program
(the usual setting); Out 1,2–7,8, Out 1–8 or Sub 1–8 in Standalone Mode; and Out
1,2–31,32 or Out 1–32 in Controller Mode.
Note: When set to a mono channel, the left and right channels are summed postpan knob. If the pan knob is set to the center position, the left and right channels
will be summed and padded. If the pan knob is set to the maximum left or right
positions, only the respective channel will be sent to the output.
The Inserts field shows any enabled or disabled effects for that pad. Tap the area
under Inserts to open a window where you can load, change, and enable or
disable the effects.
Tap Solo or Mute to solo or mute the pad (respectively).
Adjust the pan knob or level slider to change the panning or level of the pad. The
green level meter next to the slider shows the pad’s current volume level in dB.
110
When viewing the program channel strip while using a drum program, keygroup
program, clip program, or plugin program:
The first field shows the current program number and name (which you can
change).
The second field shows where the program is routed, which you can change:
Out 1,2–7,8, Out 1–8 or Sub 1–8 in Standalone Mode; and Out 1,2–31,32 or
Out 1–32 in Controller Mode.
Note: When set to a mono channel, the left and right channels are summed
post-pan knob. If the pan knob is set to the center position, the left and right
channels will be summed and padded. If the pan knob is set to the maximum
left or right positions, only the respective channel will be sent to the output.
The Inserts field shows any enabled or disabled effects for that program. Tap
the area under Inserts to open a window where you can load, change, and
enable or disable the effects.
Tap Solo or Mute to solo or mute the program (respectively). Alternatively,
press Solo or Mute under the LED meters (MPC X).
To change the program’s automation, tap the program automation button
or press Read/Write (MPC X) to cycle through its three states:
When off, the program will ignore automation data. If you have already
recorded or entered automation, tapping this will switch between Read (R)
and Write (W) only, but you can override this and turn it off by pressing and
holding Shift while tapping the button.
Important: If you have already recorded automation and turn it off, the
track will still use the effect and its parameter values at the point where you
turned it off.
When set to Read (R), the program will read automation data but will not
record any additional automation over it. (Think of this as a protective
feature to prevent accidental changes to your automation while recording.)
When set to Write (W), the program can record automation. (If you have
any Q-Link knobs assigned to automatable parameters, make sure not to
touch any accidentally while you are recording.)
Tip: You can quickly set all programs and audio tracks to the same
automation by tapping the global automation button in the upper-right corner
of the screen. See General Features > Automation to learn about this.
Adjust the pan knob or level slider to change the panning or level of the
program. The green level meter next to the slider shows the program’s current
volume level in dB.
When viewing the track channel strip while using a MIDI track:
The first field shows the current track (which you can change) and its name.
The second field shows the name of the program the track is using.
Tap Solo or Mute to solo or mute the track (respectively).
Adjust the pan knob or level slider to change the panning or level of the track.
The blue level meter next to the slider shows the track’s current velocity level.
Note: If the track is using a plugin program, then the slider will send CC #7
(Volume) and the knob will send CC #10 (Pan) to your instrument plugin. The
plugin will then handle these messages as it normally would.
111
When viewing the track channel strip while using an audio track:
The first field defines the input source of the external audio signal, which you can
set to a pair of inputs (Input 1,2–3,4 in Standalone Mode, Input 1,2–31,32 in
Controller Mode) or a single input (Input 1–4 in Standalone Mode, Input 1–32 in
Controller Mode).
The second field shows where the track is routed, which you can change: Out
1,2–7,8, Out 1–8 or Sub 1–8 in Standalone Mode; and Out 1,2–31,32 or Out
1–32 in Controller Mode.
Note: When set to a mono channel, the left and right channels are summed
post-pan knob. If the pan knob is set to the center position, the left and right
channels will be summed and padded. If the pan knob is set to the maximum
left or right positions, only the respective channel will be sent to the output.
The Inserts field shows any enabled or disabled effects for that track. Tap the
area under Inserts to open a window where you can load, change, and enable
or disable the effects.
Tap Solo or Mute to solo or mute the track (respectively). Alternatively, press
Solo or Mute under the LED meters (MPC X).
To change the audio track’s automation, tap the track automation button
or press Read/Write (MPC X) to cycle through its three states:
When off, the audio track will ignore automation data. If you have already
recorded or entered automation, tapping this will switch between Read (R)
and Write (W) only, but you can override this and turn it off by pressing and
holding Shift while pressing or tapping the button.
Important: If you have already recorded automation and turn it off, the
track will still use the effect and its parameter values at the point where you
turned it off.
When set to Read (R), the audio track will read automation data but will not
record any additional automation over it. (Think of this as a protective
feature to prevent accidental changes to your automation while recording.)
When set to Write (W), the audio track can record automation. (If you have
any Q-Link knobs assigned to automatable parameters, make sure not to
touch any accidentally while you are recording.)
Tip: You can quickly set all programs and audio tracks to the same
automation by tapping the global automation button in the upper-right corner
of the screen. See General Features > Automation to learn about this.
Adjust the pan knob or level slider to change the panning or level of the track.
The green level meter next to the slider shows the track’s current volume level
in dB.
To record-enable the track, tap the Record Arm button or press Rec Arm
(MPC X). When you begin audio recording, the audio signal will be recorded to
this track.
Tip: You can select multiple tracks in the Track View by pressing and holding
Shift while tapping the Arm button to each track.
When viewing the master channel strip:
The first field shows the current master output as a stereo pair (which you can
change).
The Inserts field shows any enabled or disabled effects for that pair of outputs.
Tap the area under Inserts to open a window where you can load, change, and
enable or disable the effects.
Tap Mute to mute the master output.
Adjust the pan knob or level slider to change the panning or level of the master
output. The green level meter next to the slider shows the outputs’ current
volume level in dB.
112
Sequence Section
The Sequence section shows the current sequence and its information.
Use Sequence field to select a sequence.
To edit the name of the sequence, tap the cursor icon on the right edge of
the section, and use the virtual keyboard that appears.
Use the BPM field to adjust the tempo of the sequence.
To set whether the sequence follows its own tempo (Sequence) or a
master tempo (Master), tap the Sequence/Master button under the BPM
field. Alternatively, press and hold Shift+Tap.
Use the Bars field to adjust the length of the sequence in bars.
The Loop button shows whether the sequence (or a part of it) will loop or not.
To enable or disable looping, tap the button.
To set the start point and end point of loop, tap the Start or End field
(respectively) and then use the data dial or the –/+ buttons, or double-tap the
field and use the numeric keyboard that appears.
Note: The Last Bar value of the Delete Bars and Copy Bars processes
depends on the total length of the sequence.
Use the Transpose field to set the transposition (in semitones) of the entire
sequence.
113
To edit the sequence, tap the pencil icon on the right edge of the section. The Sequence Edit/Copy window will open.
You can use any of these functions as described below, though there are fewer options for audio tracks than for MIDI
tracks.
To return to Main Mode, tap Cancel or the left arrow () in the upper-left corner of the screen. Alternatively, press
Main.
To edit the name of the sequence, tap the top of the screen and use the virtual keyboard that appears.
114
The Erase function erases all or part of a track in a specific
sequence.
To select the sequence you want to erase, use the
Sequence field.
To select the track you want to erase within the
sequence, use the Track field.
To set the time range of the sequence you want to
erase, use the Bar, Beat, and Tick fields. The left
fields set the start of the time range, and the right
fields set the end of the time range.
To select what types of events you erase, select one
of the Erase options:
All erases all pad events from the designated time
range and reset all of its settings.
Automation erases only automation from the
designated time range.
Note erases only specific pad events from the
designated time range. In the diagram of the eight
pad banks that appears, press each pad in each
bank to select or deselect its notes. This option is
available only for MIDI tracks, not audio tracks.
Except Note erases everything except pad events
from the designated time range. This option is
available only for MIDI tracks, not audio tracks.
To confirm your choice, tap Do It.
To return to the previous screen, tap  Back or
anywhere outside the window.
To cancel and return to Main Mode, tap Cancel.
The Clear function erases all events from the sequence
and resets all of its settings.
To confirm your choice, tap Clear.
To return to the previous screen, tap Cancel.
115
The Transpose function transposes a range of events on a
track in a sequence. The events within that range will shift
accordingly in the Grid View. This option is available for
MIDI tracks only.
To select the sequence you want to transpose, use
the Sequence field.
To select the track you want to transpose within
the sequence, use the Track field.
To set the time range of the sequence you want to
transpose, use the two sets of Bar, Beat, and Tick
fields. The left fields set the start of the time range, and
the right fields set the end of the time range.
For drum programs, use the two Pad fields to select
the “source” pad (whose events you want to move) and
“destination” pad (where the events will be placed). Tap
each field and then press the desired pad.
For keygroup programs, plugin programs, and MIDI
programs, set the range and amount of transposition:
Range: Use the two Note fields to set the range of
notes of the events you want to transpose. Note
events within this range will be transposed, while
note events outside of this range will remain
unchanged.
Transpose: Use this field to set how many
semitones up or down you want to transpose the
note events.
To confirm your choice, tap Do It.
To return to the previous screen, tap  Back or
anywhere outside the window.
To cancel and return to Main Mode, tap Cancel.
The Bounce to Sample function immediately renders the
sequence (all of its tracks) as an audio sample and places it
in the project’s sample pool. By default, it will be named
Bounce - and appended with the sequence name.
If you have already used this function on this sequence,
then you will be asked if you want to overwrite the existing
sample with this new one or cancel.
To continue and save the sequence over the
existing one, tap Replace.
To cancel, tap Cancel.
116
The Delete Bars function removes a range of bars from a
sequence.
To select the sequence whose bars you want to
delete, use the Sequence field.
To set the range of bars you want to delete, use the
First Bar and Last Bar fields. The bar in each field and
all bars in between them will be deleted.
To confirm your choice, tap Do It.
To return to the previous screen, tap  Back or
anywhere outside the window.
To cancel and return to Main Mode, tap Cancel.
The Insert Bars function adds empty bars to a sequence
at a specified point.
To select the desired sequence, use the Sequence
field.
To set how many bars you will insert, use the # of
Bars field.
To set the time signature of the inserted bars, use
the two Time Sig fields.
To set where you will insert the bars, use the Before
Bar field. The bars will be inserted before this one.
To confirm your choice, tap Do It.
To return to the previous screen, tap  Back or
anywhere outside the window.
To cancel and return to Main Mode, tap Cancel.
The Half Length function will immediately halve the
length of the sequence (without deleting any note events).
The Double Length function will immediately double the
sequence and copy all events from the first half to the
second half.
117
The Copy Sequence function copies the contents of one
sequence to another.
To select the “source” sequence, use the Copy
Contents of Sequence field. This is the sequence
whose events you want to copy.
To select the “destination” sequence, use the Over
Contents of Sequence field. This is the sequence
where the source sequence will be copied.
To confirm your choice, tap Do It.
To return to the previous screen, tap  Back or
anywhere outside the window.
To cancel and return to Main Mode, tap Cancel.
The Copy Bars function copies a range of bars from a
sequence and adds them to another at a specified point.
To select the “source” sequence, use the From
Sequence field. This is the sequence whose bars you
want to copy.
To set the range of bars to copy in the source
sequence, use the First Bar and Last Bar fields.
To select the “destination” sequence, use the To
Sequence field. This is the sequence where the source
sequence bars will be copied.
To set where you want to add the copied bars, use
the After Bar field. The copied bars will be inserted
after this one.
To set how many instances of the copied bars you
want to add, use the Copies field.
To overwrite the destination sequence, tap Replace.
To add the events to the destination sequence
without erasing anything, tap Merge.
To return to the previous screen, tap  Back or
anywhere outside the window.
To cancel and return to Main Mode, tap Cancel.
118
The Copy Events function copies a range of events or
selected audio track regions from a sequence and adds
them to another at a specified point.
To select the “source” sequence, use the From
Sequence field. This is the sequence whose content
you want to copy.
To select the “source” track, use the From Track
field. This is the track whose content you want to copy.
To specify the pads or notes to copy events from,
use the Pads or Notes field. By default, this will be set
to All to copy all events in the current track.
To set the time range of the events or the audio
track you want to copy, use the Bar, Beat, and Tick
fields. The left fields set the start of the time range, and
the right fields set the end of the time range.
To set what content is copied, use the field below
the dotted arrow. Copy All Events will copy and paste
all events in the track. Copy Only Selected Events will
copy and paste only the events that are currently
selected.
To select the “destination” sequence, use the To
Sequence field. This is the sequence where the
content of the source sequence will be copied.
To select the “destination” track, use the To Track
field. This is the track where the content of the source
track will be copied.
To set where you want to add the copied events or
audio track, use the Bar, Beat, and Tick fields. The
events or audio track will be added after this point.
To set how many instances of the copied events or
audio track you want to add, use the Copies field.
To set whether you want to copy the events in the
time range or the selected notes in the Grid View or
List Edit Mode, use the Selection field. Set this to All
events to copy the notes in the time range determined
by the Bar, Beat, and Tick fields above, or set this to
Selected events to copy only the events currently
selected in the Grid View or List Edit Mode. This field is
available for MIDI tracks only.
To overwrite the destination sequence, tap Replace.
To add the events to the destination sequence
without erasing anything, tap Merge.
To return to the previous screen, tap  Back or
anywhere outside the window.
To cancel and return to Main Mode, tap Cancel.
119
The Save Current Sequence function saves the current
sequence to an external storage device or the internal
drive of MPC X or MPC Live.
To select the storage device you want to view, tap it
in the Storage column on the left.
Internal is the internal drive of MPC X or MPC Live.
MPC Documents is a shortcut to the MPC
Documents folder on the internal drive of MPC X
or MPC Live.
If you have storage devices connected to USB
ports or SD card slot of MPC X, MPC Live, or your
computer (with MPC Touch), they will appear in
this column, as well.
To enter a folder, double-tap it. Alternatively, turn the
data dial or use the –/+ buttons to move through the
list, and press the center cursor or Enter (MPC X) or
the data dial (MPC Live, MPC Touch) to enter a folder.
You can also tap one of the five folder buttons in the
upper-right to jump immediately to those pre-assigned
file paths (see Browser to learn how to do this).
To create a new folder, tap New Folder, use the
virtual keyboard that appears to enter a name, and then
tap Do It. You will immediately enter the new folder.
To move up one folder level, tap the folder/ icon in
the upper-left corner.
To name the file, tap the File Name field at the bottom
of the screen, and use the virtual keyboard that appears.
To save the file, tap Save.
To cancel and return to the Menu, tap Cancel.
Alternatively, tap the  icon in the upper-left corner.
120
Track Section
The Track section shows the current track, program type, and its information.
The Track section while using a MIDI track.
The Track section while using an audio track.
The Track field shows the track number and its name.
To edit the name of the track, tap the cursor icon on the right edge of the section and use the virtual keyboard that
appears.
While using a MIDI track:
The program selector indicates the type of program through which the track is being routed. The specific
program name is displayed below in the Program section. You can use the program selector to change program
type (and then select a specific program of that type in the Program section below it).
To select a drum program, tap the four-squares icon.
To select a keygroup program, tap the piano-keys icon.
To select a clip program, tap the play-button icon.
To select a MIDI program, tap the bars icon.
To select a CV program, tap the CV icon.
To select a plugin program, tap the plug icon.
Use the Length field to set how long the track is in beats. If you select the minimum value, Seq or 0 (if you use
the numeric keypad), the track will be the exact same length as its sequence.
Tip: This feature lets you maintain tracks of different lengths. For instance, you could play a 1-bar drum sequence
repeatedly under a 4-bar bass line.
Use the Velocity field to set how loudly or quietly a track plays relative to its recorded levels. When set to 50%,
the track will be played with half the velocity it was originally played. When set to 200%, the track will play twice
as loud. The maximum velocity level is still 127, though.
Use the Transpose field to set the transposition (in semitones) of the entire track.
121
While using an audio track:
Tap the Record Arm button to record-enable the track. When you begin audio recording, the audio signal will be
recorded to this track.
Tip: You can select multiple tracks in the Track View by pressing and holding Shift while tapping the Arm button
to each track.
Use the Monitor button to set how your audio track will be monitored. Tapping it will cycle through its three states:
When set to Auto, you will hear incoming audio while the track is record-enabled only.
When on, you will hear incoming audio whether or not the track is record-enabled.
When off, you will never hear any incoming audio.
To edit the track, tap the pencil icon on the right edge of the section. The Track Edit window will open.
While using MIDI tracks, you can use any of these functions as described below.
To return to Main Mode, tap Cancel or the left arrow () in the upper-left corner of the screen. Alternatively, press
Main.
To edit the name of the track, tap the top of the screen and use the virtual keyboard that appears.
122
The Clear function erases all events from the track and
resets all of its settings.
To confirm your choice, tap Clear.
To return to the previous screen, tap Cancel.
The Explode function immediately splits the current track
into multiple tracks—one for each distinct pad or note
(pitch, not event). The current track also remains present
and intact, while each track created from it is labeled with
the track name and pad name or number.
The Double-Speed Events function immediately halves
the lengths of all note events on the track as well as the
distance between them. In other words, the track’s notes
are pressed closer together so the track sounds like it is
playing at twice the previous speed. This does not actually
affect the pitches of notes or the tempo.
The Half-Speed Events function immediately doubles the
lengths of all note events on the track as well as the
distance between them. In other words, the track’s notes
are spread further apart so the track sounds like it is
playing at half of the previous speed. This does not
actually affect the pitches of notes or the tempo.
The Copy Track function copies the contents of one track
to another.
To select the “source” track, tap the Copy Contents
of Track field. This is the track whose events you want
to copy.
To select the “destination” track, tap the Over
Contents of Track field. This is the track where the
source track will be copied.
To confirm your choice, tap Do It.
To cancel and return to Main Mode, tap Cancel.
The Split Events function divides note events to create
new rhythms and patterns.
To select the how many events to create, use the
Into slider. Select 2 to 32 events.
To apply the split to selected events, tap the Only
selected events field. Leave this unchecked to split all
note events in the track.
To confirm your choice, tap Do It.
To cancel and return to Main Mode, tap Cancel.
123
The Pitch Quantize function forces the pitches of note
events into a specific scale.
To select the desired root note of the scale, use the
Root Note field.
To select a type of scale, use the Scale field.
To determine which note events will be quantized,
tap the Only apply to selected events checkbox.
When on, only the currently selected note events
will be quantized.
When off, all pitches in the current track will be
quantized.
To set lowest-possible and highest-possible pitches
where the quantized note events will be placed, use
the Start Note and End Note fields (respectively). If a
note event is originally outside of this range, it will be
forced to the nearest pitch (within the scale) inside the
range.
To continue and quantize the note events, tap Do It.
To cancel, tap Close.
The Humanize function applies randomization to the
timing, length, and/or velocity of MIDI note events.
To select whether or not humanization will be applied
to the timing of MIDI events, tap the Humanize Time
checkbox.
To select the maximum number of pulses by which
the timing of an event will be adjusted, use the
Amount (Pulses) slider.
To set how dramatically the humanization effect is
applied to the timing, use the Eagerness slider.
Negative values correspond to playing “ahead of the
beat” while positive values correspond to playing
“behind the beat.”
To set whether or not humanization will be applied
to the duration of MIDI note events, tap the
Humanize Note Length checkbox.
To set how dramatically the humanization effect is
applied to note lengths, use the Length (%) slider.
To set whether or not humanization will be applied
to the velocities of MIDI note events, tap the
Humanize Velocity checkbox.
To set how dramatically the humanization effect is
applied to note velocities, use the Strength (%) slider.
To determine which notes will use these
humanization values, tap the Only Apply to
Selected Events checkbox.
When on, just the currently selected notes will be
humanized.
When off, all notes in the track will be humanized.
To apply humanization and keep this window open,
tap Apply.
To apply humanization and close the window, tap
Do It.
To close the window without making any changes,
tap Close.
124
The Generate Random Events function creates random
melodic or drum patterns on the current MIDI track.
To select the type of events you want to create, use
the Event Type field to select Drum Events or
Melodic Events.
To select how the events will be created relative to
the existing events on the track, use the Replace
field:
Replace All Events: Select this option to replace all
events on the track with the randomly generated
ones.
Replace Events in Note Range: Select this option
to replace all events in the designated note range
on the track with the randomly generated ones.
Use the Bank or Start Pad and End Pad menus
to set the note range for drum events or the Start
Note and End Note menus to set the note range
for melodic events.
Add to Existing Events: Select this option to add
the randomly generated events to the track
without replacing or overwriting the existing ones.
To set how many bars the events will use, use the
Pattern Size (Bars) field. The highest possible value
is the number of bars in the current sequence.
To select the duration of the events, use the Note
Length field. (This feature is nonfunctional if Legato
is enabled while generating melodic events.)
To generate the events and keep this window open,
tap Apply.
To generate the events and close the window, tap
Do It.
To close the window without generating any events,
tap Close.
If Event Type is set to Drum Events:
To select the pad bank that will be used to
generate the events, use the Bank field or select
Range to use the Start Pad and End Pad menus
to define a specific pad range instead.
To define a specific pad range over which the
events will be generated, use the Start Pad or
End Pad fields. You can use these fields only if
the Bank menu is set to Range.
To set how closely together the events will be
placed in the track, use the Density (%) slider.
To set how widely or narrowly the rhythmic
patterns of the generated notes vary, use the
Rhythm Variation slider.
125
If Event Type is set to Melodic Events:
To define a specific note range over which the
events will be generated, use the Start Note or
End Note fields.
To enable or disable legato, tap the Legato
checkbox.
When on, the generated notes will be
extended or shortened to create a long,
unbroken phrase from the first note event’s
start point to the last note event’s end point.
Each note event will sustain until another
note event starts. If multiple note events start
at the same time (and are not the last note
events), their lengths will become identical.
When off, the generated notes will use the
duration set by the Note Length menu.
To set the maximum number of note events that
can be sounding simultaneously in the track,
use the Polyphony field to select 1–8.
To determine whether or not the notes will use
a scale, tap the Constrain Notes to Scale
checkbox.
When on, the notes will be within the scale
determined by the Scale menu.
When off, the notes will be chromatic.
To set how closely together the events will be
placed in the track, use the Density (%) slider.
To set the root note of the scale that the notes
will use, use the Root Note field.
To select the scale or mode that the generated
notes will use, use the Scale field.
The Bounce to Sample function immediately renders the
track (for the current sequence only) as an audio sample
and places it in the project’s sample pool. By default, it will
be named Bounce - and appended with the track name.
This function does not work for tracks that use MIDI
programs or CV programs.
If you have already used this function on this track, then
you will be asked if you want to overwrite the existing
sample with this new one or cancel.
To continue and save the track over the existing
one, tap Replace.
To cancel, tap Cancel.
126
The Bounce to Audio Track function immediately
renders the track (for the current sequence only) as an
audio track in the project. The Main Mode will
automatically switch to the Audio tab. By default, it will be
named Audio and appended with a number (e.g., Audio
002). This function does not work for tracks that use MIDI
programs or CV programs.
If you have already used this function on this track, then
you will be asked if you want to overwrite the existing
sample with this new one or cancel.
To continue and save the track over the existing
one, tap Replace.
To cancel, tap Cancel.
The Export as Pattern function saves the track (for the
current sequence only) as a pattern (.mpcpattern) to an
external storage device or the internal drive of MPC X or
MPC Live.
To select the storage device you want to view, tap it
in the Storage column on the left.
Internal is the internal drive of MPC X or MPC Live.
MPC Documents is a shortcut to the MPC
Documents folder on the internal drive of MPC X
or MPC Live.
If you have storage devices connected to USB
ports or SD card slot of MPC X, MPC Live, or your
computer (with MPC Touch), they will appear in
this column, as well.
To enter a folder, double-tap it. Alternatively, turn the
data dial or use the –/+ buttons to move through the
list, and press the center cursor or Enter (MPC X) or
the data dial (MPC Live, MPC Touch) to enter a folder.
You can also tap one of the five folder buttons in the
upper-right to jump immediately to those pre-assigned
file paths (see Browser to learn how to do this).
To create a new folder, tap New Folder, use the
virtual keyboard that appears to enter a name, and then
tap Do It. You will immediately enter the new folder.
To move up one folder level, tap the folder/ icon in
the upper-left corner.
To name the file, tap the File Name field at the bottom
of the screen, and use the virtual keyboard that appears.
To save the file, tap Save.
To cancel and return to the Menu, tap Cancel.
Alternatively, tap the  icon in the upper-left corner.
127
While using audio tracks, you can use any of these functions as described below.
To return to Main Mode, tap Cancel or the left arrow () in the upper-left corner of the screen. Alternatively, press
Main.
To edit the name of the track, tap the top of the screen and use the virtual keyboard that appears.
The Delete function erases the entire audio track.
To confirm your choice, tap Clear.
To return to the previous screen, tap Cancel.
The Clear Regions function erases all regions from the
audio track without erasing the track itself.
The Reset Channel Strip function:
•
clears all Insert effect slots;
•
turns Mute, Solo, automation, and Monitor off;
•
resets the pan knob to the center;
•
resets the level slider to 0.00 dB; and
•
turns the Record Arm button off.
It does not change the track’s inputs or outputs.
128
The Copy Track function copies the contents of one track
to another.
To select the “source” track, tap the Copy Contents
of Track field. This is the track whose events you want
to copy.
To select the “destination” track, tap the Over
Contents of Track field. This is the track where the
source track will be copied.
To rename the "destination" track, use the Track
Name field.
To confirm your choice, tap Do It.
To cancel and return to Main Mode, tap Cancel or
anywhere outside the window.
The Save Current Channel Strip function saves the
current settings of the track channel strip (for the current
audio track) to an external storage device or the internal
drive of MPC X or MPC Live.
To select the storage device you want to view, tap it
in the Storage column on the left.
Internal is the internal drive of MPC X or MPC
Live.
MPC Documents is a shortcut to the MPC
Documents folder on the internal drive of MPC X
or MPC Live.
If you have storage devices connected to USB
ports or SD card slot of MPC X, MPC Live, or your
computer (with MPC Touch), they will appear in
this column, as well.
To enter a folder, double-tap it. Alternatively, turn the
data dial or use the –/+ buttons to move through the
list, and press the center cursor or Enter (MPC X) or
the data dial (MPC Live, MPC Touch) to enter a folder.
You can also tap one of the five folder buttons in the
upper-right to jump immediately to those pre-assigned
file paths (see Browser to learn how to do this).
To create a new folder, tap New Folder, use the
virtual keyboard that appears to enter a name, and
then tap Do It. You will immediately enter the new
folder.
To move up one folder level, tap the folder/ icon in
the upper-left corner.
To name the file, tap the File Name field at the
bottom of the screen, and use the virtual keyboard that
appears.
To save the file, tap Save.
To cancel and return to the Menu, tap Cancel.
Alternatively, tap the  icon in the upper-left corner.
129
Program Section
The Program section shows the current program. This section will appear differently depending on the type of
program selected in the Track section above it.
For all program types while using MIDI tracks, you can do the following:
To edit the name of the program, tap the cursor icon on the right edge of the section. Use the virtual keyboard
that appears to enter a new name, and then tap Do It.
To create a new program of the currently selected type, tap the + icon. A new program of the same type will
be created and appended with a number (e.g., Program 002).
For all program types while using audio tracks, you can do the following:
To change the input source, tap Input Config. This will show or hide the track channel strip. If you are viewing the
audio track channel strip (not the master channel strip), the first field will be automatically selected.
To enter Audio Edit Mode, tap Edit Audio. This is the same as tapping the waveform-and-box icon on the left
edge of the screen.
While viewing drum programs, the Drum Program field shows the name of the program.
Tap Warp Samples to enter the first Sample tab in Program Edit Mode immediately (see Program Edit Mode >
Drum Programs to learn about this).
Tap Assign Samples to enter the Sample Assign tab in the Browser immediately (see Browser to learn about this).
Tap Edit Samples to enter Program Mode in Sample Edit Mode immediately (see Sample Edit Mode > Program
Mode to learn about this). The sample shown will be the one in the top layer of the last pad you pressed.
While viewing keygroup programs, the Keygroup Program field shows the name of the program.
While viewing clip programs, the Clip Program field shows the name of the program.
Tap Edit Clips to enter Program Edit Mode, where you can assign samples (clips) to pads, edit each clip, and
configure how each clip plays when launched (see Program Edit Mode > Clip Programs to learn about this).
130
While viewing plugin programs, the Plugin Program field shows the name of the program.
Use the Plugin field to select the plugin the program is using. In the screen that appears, you can tap the Type or
Manufacturer button at the bottom of the screen to enable or disable sorting of your plugins by type or maker.
Note: You have to specify the disk directory where your plugins are located. This can be done in the software’s
Preferences. See user guide in the MPC software to learn how to do this: click the Help menu, select MPC
Help, and select MPC User Manual.
Use the MIDI Ch field to select the MIDI channel the program uses. Use this setting when you are working with a
virtual instrument plugin that supports multi-mode.
Use the Preset field to select a preset (if any) within the plugin the program is using.
While viewing MIDI programs, the MIDI Program field shows the name of the program.
Use the MIDI Port field to select the port over which the program sends its MIDI data.
Note: You also have to configure the MIDI ports in the Preferences. See the user guide in the MPC software to
learn how to do this: click the Help menu, select MPC Help, and select MPC User Manual.
Use the Program Ch field to select the program change message the program sends out.
Use the MIDI Ch field to select the MIDI channel over which the program sends its MIDI data.
Use the Bank MSB and Bank LSB fields to select the messages for Most Significant Byte and Least Significant
Byte (respectively) that the program sends out.
While viewing CV programs, the CV Program field shows the name of the program.
Use the Note field to select the note tracking—the program’s note track: Lowest, Highest, or Last.
Use the CV Port field to select the CV port the program is using.
Use the Gate Port field to select the Gate port the program is using.
Use the Mod Wheel field to select the CV port used by a modulation wheel on an external controller.
Use the Velocity Port field to select CV port the program will use to transmit velocity values.
131
To edit the program, tap the pencil icon on the right edge of the section. The Program Edit/Copy window will
open.
You can use any of these functions as described below.
To return to Main Mode, tap Cancel or the left arrow () in the upper-left corner of the screen. Alternatively,
press Main.
To edit the name of the program, tap the top of the screen and use the virtual keyboard that appears.
The Delete function erases all events from the track and
resets all of its settings.
To confirm your choice, tap Clear.
To return to the previous screen, tap Cancel.
The Duplicate function immediately creates an identical
program. The duplicate program will use the same name
but appended with a number (e.g., Program 002).
132
The Duplicate to Track function immediately creates an identical program on a new track. The duplicate program
will use the same name but appended with a number (e.g., Program 002). The new track will be named Track and
appended with a number (e.g., Track 06).
The Bounce to Sample function immediately renders all tracks that use that program (for the current sequence only)
as an audio sample and places it in the project’s sample pool. By default, it will be named Bounce - and appended with
the program name. This function does not work for MIDI programs or CV programs.
If you have already used this function on this program, then you will be asked if you want to overwrite the
existing sample with this new one or cancel.
To continue and save the program over the existing one, tap Replace.
To cancel, tap Cancel.
The Bounce to Audio Track function immediately renders that program (for the current sequence only) as an audio
track in the project. The Main Mode will automatically switch to the Audio tab. By default, it will be named Audio and
appended with a number (e.g., Audio 002). This function does not work for MIDI programs or CV programs.
If you have already used this function on this track, then you will be asked if you want to overwrite the existing
sample with this new one or cancel.
To continue and save the track over the existing one, tap Replace.
To cancel, tap Cancel.
The Flatten Pad function renders all samples on a pad as
an audio sample and places it on the first layer of that pad.
The resulting sample is the audio signal produced by that
pad at full velocity (127) after the pad channel strip, which
means that it includes any assigned pad insert effects and
the results of warping the sample. This function is useful if
you need to reduce how CPU-intensive a pad or program is
by essentially “embedding” the warping and effects in the
sample itself. By default, it will use the name of the first
sample. This function works for drum programs only. (This is
the same as the Flatten Pad button shown at the top of the
screen in Program Edit Mode.)
To select the pad, press it or use the Pad menu.
To set the length of the audio tail, use the Audio Tail
field. This will add extra seconds to the end of the
resulting audio file. This is useful if you are using
effects or samples whose sounds exceed the defined
audio length (e.g., long reverb or delay, one-shot
samples with long decays, etc.). We recommend using
an audio tail of at least a couple of seconds.
To name the new sample, tap the Edit Name field,
and use the virtual keyboard that appears.
To confirm your choice, tap Do It.
To cancel, tap Cancel.
133
The Save Current Program or Save Current Sample
function saves the current program or sample (the top
layer of the last pad you pressed) (respectively) to an
external storage device or the internal drive of MPC X or
MPC Live.
To select the storage device you want to view, tap it
in the Storage column on the left.
Internal is the internal drive of MPC X or MPC
Live.
MPC Documents is a shortcut to the MPC
Documents folder on the internal drive of MPC X
or MPC Live.
If you have storage devices connected to USB
ports or SD card slot of MPC X, MPC Live, or your
computer (with MPC Touch), they will appear in
this column, as well.
To enter a folder, double-tap it. Alternatively, turn the
data dial or use the –/+ buttons to move through the
list, and press the center cursor or Enter (MPC X) or
the data dial (MPC Live, MPC Touch) to enter a folder.
You can also tap one of the five folder buttons in the
upper-right to jump immediately to those pre-assigned
file paths (see Browser to learn how to do this).
To create a new folder, tap New Folder, use the
virtual keyboard that appears to enter a name, and
then tap Do It. You will immediately enter the new
folder.
To move up one folder level, tap the folder/ icon in
the upper-left corner.
To name the file, tap the File Name field at the
bottom of the screen, and use the virtual keyboard that
appears.
To save the file, tap Save.
To cancel and return to the Menu, tap Cancel.
Alternatively, tap the  icon in the upper-left corner.
134
Grid View
The Grid View lets you view and edit the note events of each track of a sequence in a project
and their velocities. This mode has two different appearances: one for drum programs and one
for keygroup programs, MIDI programs, and plugin programs.
For drum programs, the left column shows you all available pads in a vertical view with their corresponding data.
For keygroup programs, plugin programs, and MIDI programs, the left column shows a vertical “piano roll” keyboard.
To enter the Grid View, press Menu, and then tap Grid View.
Note: The Grid View option is available when the currently selected track is a MIDI track. When an audio track is
selected, it will show an icon for Audio Edit Mode instead of Grid View. To select a MIDI track (and enable Grid View),
press Main to enter Main Mode, and then tap MIDI in the lower-left corner.
Grid View of a drum program.
Grid View of a keygroup program or MIDI program.
The top of the screen shows the track name, sequence and timing information, and editing tools.
Use the Track field to select which track of the current sequence you want to show in the grid.
Use the Bars field to set the length of the sequence.
The time counter at the top of the screen indicates the current playhead position. This is shown in most of the
modes. See General Features > Time Counter/Locate to learn about this.
135
In the Grid View, these four tool icons enable you to use different functions in the grid.
Tap one to select its mode:
Pencil: Draw Mode:
To enter a note in an empty grid square, tap the grid square.
To select a note, tap it.
To move a note, tap and drag it to another grid square.
To erase a note, double-tap it.
Eraser: Erase Mode:
To erase a note, tap it.
Select Box: Select Mode:
Note: Notes will remain selected if you switch to another mode. The selection will change, however, if you
press a pad while Hitting Pad Selects All Events is set to On.
To select a note, tap it.
To select multiple notes, tap and drag across the grid to create a box around them.
To move a note, tap and drag it to another grid square.
To move multiple notes, select them as described above, and tap and drag them.
To erase multiple notes, select them as described above, and then select the eraser tool and tap any
of the selected notes.
Magnifying Glass: Navigation Mode:
To move to another part of the grid, tap and drag it.
To zoom in or out, spread or pinch your fingers (respectively) on the grid. You can do this vertically,
horizontally, or both at the same time.
136
The Settings window lets you configure certain Grid View settings.
To view the Settings, tap the gear icon.
Use the Snap Mode selector to set how events “snap” to the grid.
Absolute: Events will “snap” to the nearest time division on the grid (as determined by the TC field or Time
Correct window). This is the typical and traditional method of using the snap/quantization feature.
Relative: Events will “snap” to the nearest time division on the grid (as determined by the TC field or Time
Correct window) plus the original time position of the event (e.g., an event that is originally three ticks past a
time division on the grid will snap only to positions that are three ticks past every time division).
Use the Hitting Pad Selects All Events selector to turn the feature on or off. When on, pressing a pad will
automatically select all note events for that pad in the sequence on that track. When off, pressing a pad will simply
play its sound without selecting any note events.
Use the Auto-Scroll selector to set how the screen behaves relative to the audio playhead.
Follow: Depending on the zoom setting, the grid will scroll along in the background while keeping the audio
playhead centered.
Page: The grid will move to the “next page” to follow the audio playhead.
Off: The grid will not move at all.
These functions also apply to Audio Edit Mode, List Edit Mode, and Sample Edit Mode.
Use the Link Zoom and Scroll selector to turn the feature on or off. When on, the zoom and scroll levels in the MPC
software and your MPC hardware will always be the same. When off, the grid views can be adjusted separately using
the MPC software and your MPC hardware.
Note: This setting is only available when connected to MPC software in controller mode.
Use the Q-Link Playhead Increment selector to set the how turning Q-Link Knob 2 (Playhead) in Q-Link Screen
Mode moves the playhead. Select 1/16th-note increments (1/16 Note) or according to the time division (TC
Division).
137
Regardless of which tool is selected, you can do any of the following to move, lengthen, shorten, or transpose any
selected note/notes.
To automatically set the grid to view one pad bank and two bars, tap the grid-and-magnifying-glass icon in
the lower-left corner.
To undo your last action, press Undo.
To redo the last action you undid, press Shift+Undo/Redo.
To select all notes for a pad, press the desired pad.
To move the selected notes, tap Nudge at the bottom of the screen, and then use the data dial or –/+ buttons
to shift the notes left or right. By default, you can position notes only by quantization values defined by the Time
Correct value (see General Features > Timing Correct (TC) to learn about this).
To move the selected notes without restricting (“snapping”) them to the quantization grid, tap and hold
Don’t Snap in the lower-left corner of the screen, and then use the data dial or –/+ buttons to shift the notes. In
this case, each nudge is equivalent to four ticks.
To adjust the start point or end point of the selected notes (without changing their position), tap Edit Start at
the bottom of the screen, and then use the data dial or –/+ buttons.
To transpose the selected notes up or down, tap Transpose at the bottom of the screen, and then use the
data dial or –/+ buttons.
To copy the selected notes instantly, press Copy. The selected notes will be duplicated and start immediately
after the end of the last selected note. Nudge will be automatically selected so you can immediately use the data
dial to move the copied notes,
To switch to the previous or next track, press and hold Shift, and then tap Track – or Track + (respectively) at
the bottom of the screen.
To mute or solo the track, press and hold Shift, and then tap Mute or Solo (respectively) at the bottom of the
screen.
138
To open the Timing Correct window, press and hold Shift, and then tap TC at the bottom of the screen. See
General Features > Timing Correct (TC) to learn about this.
To select a time division directly, double-tap the down arrow () in the upper-left corner of the grid and select a
time division.
To adjust the metronome settings, press and hold Shift, and then tap Click at the bottom of the screen. See
General Features > Metronome (Click/Metro) to learn about this.
The Grid View also contains a velocity/automation lane where you can easily adjust note velocities and automation
parameters.
The velocity lane in the Grid View.
To show or hide the velocity/automation lane:
1. Tap the up arrow (∧) button in the lower-right corner to show the velocity/automation lane.
2. Tap the down arrow (∨) to hide the velocity/automation lane.
When viewing velocity in the lane, a vertical bar represents each note’s velocity. The higher and more red the bar is,
the higher the velocity is. Yellow bars indicate a lower velocity. Bars with a gray line at the top indicate a currently
selected note.
To adjust the velocity of the selected notes, tap Velocity at the bottom of the screen, and then use the data dial
or –/+ buttons. The numeric value will appear on the screen.
See Appendix > Updates in v2.6 > New Features > Grid Automation Lanes for more information on editing
automation parameters.
139
Audio Edit Mode
Audio Edit Mode lets you view and edit the audio tracks of a sequence in a project.
To enter Audio Edit Mode, press Menu, and then tap Audio Edit Mode.
Note: The Audio Edit option is available when the currently selected track is an audio track. When a MIDI track is
selected, it will show an icon for Grid View instead of Audio Edit Mode. To select an audio track (and enable Audio
Edit Mode), press Main to enter Main Mode, and then tap Audio in the lower-left corner.
Audio Edit Mode with channel strip hidden.
Audio Edit Mode with channel strip shown.
140
Below is a brief step-by-step process so you can get started recording audio tracks quickly. Continue reading the
rest of this chapter to learn how to use Audio Edit Mode in different cases.
To record in Audio Edit Mode (or Main Mode):
1. If the channel strip is not already shown on the left side of the screen, tap the small eye icon to show it.
2. Connect a synthesizer or other line-level audio source to the appropriate input/inputs of your MPC hardware. Set
the Line/Phono selector appropriately, too.
3. Double-tap the first field to select the input source of the external audio signal, which you can set to a pair of
inputs (Input 1,2–3,4 in Standalone Mode, Input 1,2–31,32 in Controller Mode) or a single input (Input 1–4 in
Standalone Mode, Input 1–32 in Controller Mode).
4. Double-tap the second field to select where the track is routed (Out 1,2–7,8 in Standalone Mode, Out 1,2–31,32
in Controller Mode; MPC Live does not use Out 7,8 in Standalone Mode but displays them to maintain
compatibility with MPC X, which does use them).
5. Tap the Monitor button to set how your audio track will be monitored. Tapping it will cycle through its three states:
When set to Auto, you will hear incoming audio while the track is record-enabled only.
When on, you will hear incoming audio whether or not the track is record-enabled.
When off, you will never hear any incoming audio.
6. Turn the 3/4 Rec Gain knob (MPC X) or Rec Vol knob (MPC Live, MPC Touch) to set the input level while
sending an audio signal into your MPC hardware. You should now see the level in the meter. Make sure it does
not exceed the maximum level (the meter should not be “peaking” constantly).
7. If Mute and Solo are on, tap or press them so they are off. We also recommend tapping the automation button
so it is off/gray (not green/Read [R] or red/Write [W]). Alternatively, press Read/Write so it is off (MPC X).
8. Tap the Rec Arm button next to the pan knob or press Rec Arm (MPC X) to record-enable the track.
9. Press Rec to record-arm the sequence.
10. To start recording, press Play or Play Start—then play your audio source. You should hear your existing
sequence playing in the background. You’ll see the waveform appear as a single “track region” as you record.
11. To stop recording, press Stop.
141
The top of the screen shows the track name, sequence and timing information, and editing tools.
Use the Track field to select which track of the current sequence you want to show in the grid.
Use the Bars field to set the length of the sequence.
The time counter at the top of the screen indicates the current playhead position. This is shown in most of the
modes. See General Features > Time Counter/Locate to learn about this.
In Audio Edit Mode, these six tool icons enable you to use different functions in the track.
Tap one to select its mode:
Marquee: Marquee Mode:
To select a track region, tap the upper third of it.
To move a track region (or multiple selected track regions), tap and drag the upper third of it left or right.
To split the track at two specific points (creating a track region on either side and between them), tap and
drag across the middle third of it to create a translucent white box, and then tap the upper third of that box.
To shorten or lengthen a track region (or multiple selected track regions), tap and drag the lower third
of it left or right.
Arrow: Selection Mode:
To select a track region, tap it.
To select multiple track regions, tap and drag across the grid to create a box that highlights them.
Double-tap the selected track regions to deselect them.
To move a track region (or multiple selected track regions), tap and drag the upper third of it left or right.
To shorten or lengthen a track region (or multiple selected track regions), tap its edge and drag it.
Eraser: Erase Mode:
To select multiple track regions, tap and drag across the grid to create a box that highlights them.
To erase a track region (or multiple selected track regions), tap it.
142
Scissors: Split Mode:
To split the track at a specific point (creating a track region on either side), tap that point in the track.
To select a track region, tap its left-most edge.
To select multiple track regions, tap and drag across the grid to create a box that highlights them.
Double-tap the selected track regions to deselect them.
Mute: Mute Mode:
To select multiple track regions, tap and drag across the grid to create a box that highlights them.
Double-tap the selected track regions to deselect them.
To mute or unmute a track region (or multiple selected track regions), tap it.
Magnifying Glass: Navigation Mode:
To move to another part of the track, tap and drag it.
To zoom in or out, spread or pinch your fingers (respectively) on the grid. You can do this vertically,
horizontally, or both at the same time.
The Settings window lets you configure certain Audio Edit Mode settings.
To view the Settings, tap the gear icon.
Use the Snap Mode selector to set how events “snap” to the grid.
Absolute: Events will “snap” to the nearest time division on the grid (as determined by the TC field or Time
Correct window). This is the typical and traditional method of using the snap/quantization feature.
Relative: Events will “snap” to the nearest time division on the grid (as determined by the TC field or Time
Correct window) plus the original time position of the event (e.g., an event that is originally three ticks past a
time division on the grid will snap only to positions that are three ticks past every time division).
Use the Auto-Scroll selector to set how the screen behaves relative to the audio playhead.
Follow: Depending on the zoom setting, the waveform display will scroll along in the background while keeping
the audio playhead centered.
Page: The waveform display will move to the “next page” to follow the audio playhead.
Off: The waveform display will not move at all.
These functions also apply to the sample waveform in Sample Edit Mode.
143
On the left edge of the screen, next to the five mode icons, there are two small
icons that control the channel strip.
To show or hide the channel strip, tap the eye icon.
The icon below the eye icon indicates the type of channel strip (see next
description).
The channel strip contains some important settings for the audio track or master
output, depending on the currently selected icon:
To view the track channel strip, tap the waveform icon.
To view the master channel strip, tap the crown icon.
When viewing the track channel strip while using an audio track:
The first field defines the input source of the external audio signal, which you
can set to a pair of inputs (Input 1,2–3,4 in Standalone Mode, Input 1,2–31,32
in Controller Mode) or a single input (Input 1–4 in Standalone Mode, Input 1–
32 in Controller Mode).
The second field shows where the track is routed, which you can change: Out
1,2–7,8, Out 1–8 or Sub 1–8 in Standalone Mode; and Out 1,2–31,32 or Out
1–32 in Controller Mode.
Note: When set to a mono channel, the left and right channels are summed
post-pan knob. If the pan knob is set to the center position, the left and right
channels will be summed and padded. If the pan knob is set to the maximum
left or right positions, only the respective channel will be sent to the output.
The Inserts field shows any enabled or disabled effects for that track. Tap the
area under Inserts to open a window where you can load, change, and enable
or disable the effects.
Tap Solo or Mute to solo or mute the track (respectively).
Tap the Monitor button to set how your audio track will be monitored. Tapping
it will cycle through its three states:
When set to Auto, you will hear incoming audio while the track is recordenabled only.
When on, you will hear incoming audio whether or not the track is recordenabled.
When off, you will never hear any incoming audio.
144
Tap the track automation button or press Read/Write (MPC X) to cycle
through its three states:
When off, the audio track will ignore automation data. If you have already
recorded or entered automation, tapping this will switch between Read (R)
and Write (W) only, but you can override this and turn it off by pressing and
holding Shift while pressing or tapping the button.
Important: If you have already recorded automation and turn it off, the
track will still use the effect and its parameter values at the point where you
turned it off.
When set to Read (R), the audio track will read automation data but will not
record any additional automation over it. (Think of this as a protective
feature to prevent accidental changes to your automation while recording.)
When set to Write (W), the audio track can record automation. (If you have
any Q-Link knobs assigned to automatable parameters, make sure not to
touch any accidentally while you are recording.)
Tip: You can quickly set all programs and audio tracks to the same
automation by tapping the global automation button in the upper-right corner
of the screen. See General Features > Automation to learn about this.
To change the panning or level of the track, adjust the pan knob or level
slider.
To record-enable the track, tap the Record Arm button or press Rec Arm
(on MPC X when the track name is shown in the display strip below the level
meters). When you begin audio recording, the audio signal will be recorded to
this track.
Tip: You can select multiple tracks in the Track View by pressing and holding
Shift while tapping the Arm button to each track.
When viewing the master channel strip:
The first field shows the current master output as a stereo pair (which you can
change).
The Inserts field shows any enabled or disabled effects for that pair of outputs.
Tap the area under Inserts to open a window where you can load, change, and
enable or disable the effects.
Tap Mute to mute the master output.
Adjust the pan knob or level slider to change the panning or level of the
master output.
145
Regardless of which tool is selected, you can do any of the following to edit the selected audio track regions.
Tip: If you want to hear only the audio track while editing, use the Solo button in the track channel strip to solo it.
To select a track region, tap the arrow icon to enter Selection Mode and tap a track region. When a track
region is selected, all region parameters will be available to edit.
To undo your last action, press Undo.
To redo the last action you undid, press Shift+Undo/Redo.
To move the selected track region, tap Nudge at the bottom of the screen, and then use the data dial or –/+
buttons to shift the track region left or right. Alternatively, if the arrow tool or marquee tool are selected, tap
and drag the upper third of the selected track region left or right. By default, you can move a track region only by
quantization values defined by the Time Correct value (see General Features > Timing Correct (TC) to learn
about this).
To move the selected track region without restricting (“snapping”) it to the quantization grid, tap and hold
Don’t Snap in the lower-left corner of the screen, and then use the data dial or –/+ buttons to shift the track
region. In this case, each nudge is equivalent to four ticks.
To adjust the start point or end point of the selected track region (without changing its position), tap Edit
Start at the bottom of the screen, and then use the data dial or –/+ buttons.
To split the track at the current playhead position (creating a track region on either side), tap Split at the
bottom of the screen.
To copy, cut, or paste the selected track region,
press Copy or press and hold Shift, and then tap
Copy or Cut. Turn the data dial to move the
highlighted track region, and then press the center
cursor or Enter (MPC X) or the data dial (MPC Live,
MPC Touch) to paste it at its current location.
Alternatively, press and hold Shift, and then tap
Paste (respectively).
To cut, copy, or paste the selected track region,
press and hold Shift, and then tap Cut, Copy, or
Paste (respectively) at the bottom of the screen.
To duplicate the selected track region, tap Duplicate at the bottom of the screen. The duplicate track region
will appear immediately after the original one.
To create a fade-in or fade out for the selected track region, use the Fade In or Fade Out fields, respectively.
The fades will be shown as a sloped line at the start or end of the track region.
To set the level of the selected track region, use the Level field. The waveform amplitude will change accordingly.
146
To reverse the selected track region, tap Reverse.
To mute the selected track region, tap Mute.
To lengthen or shorten the selected track region without changing its pitch, tap Warp, which will enable the
Semi, Fine, and BPM fields next to it. Use the BPM field to change the tempo, which will change the length of
the track region accordingly. Use the Semi and Fine fields if you want to change the pitch (this is useful for
matching the durations of two samples with different pitches).
Tip: You can configure audio track recording to ensure the resulting track region is warped automatically. You can
then adjust the sequence tempo while track region remains in time. See Menu > Preferences > General to learn
about this.
Note: When you record an audio file, the current sequence tempo will be embedded with it. This information is
stored within the sample file when you save the project. When you warp an audio track region, the warping
algorithm uses this sequence tempo and the current value in the BPM field to generate the “stretch factor.”
Note: The Warp algorithms are very CPU-intensive and can result in audio drop-outs during playback if used too
freely. Be mindful of how (and how often) you use the warp function. You can reduce the CPU resources required
by doing any/all of the following:
•
Minimize the amount of pitch adjustment (e.g., the Semi and Fine fields).
•
Avoid warping very small track regions.
•
Warp as few tracks or track regions as possible (i.e., reduce the number of total number of voices [of the
polyphonic limit] that use the warp algorithm at a given time), especially instances where the warped regions
start at the same time.
•
If you have warped samples used in a drum program, consider using the Flatten Pad function to consolidate
the affected pad’s layers into one audio sample (see here to learn about this). After you flatten the pad, its
sample/samples no longer need to be warped.
To open the Timing Correct window, press and hold Shift, and then tap TC at the bottom of the screen. See
General Features > Timing Correct (TC) to learn about this.
To switch to the previous or next track, press and hold Shift, and then tap Track – or Track + (respectively) at
the bottom of the screen.
To mute or solo the track, press and hold Shift, and then tap Mute or Solo (respectively) at the bottom of the
screen.
To edit automation for the track, open the automation lane. See Appendix > Updates in v2.6 > New Features
> Grid Automation Lanes for more information.
147
Track View
Track View gives you an overview of the tracks of each sequence. Use this mode to edit tracks
and sequences simultaneously.
To enter the Track View, do either of the following:
•
Press Shift+Main/Track.
•
Press Menu, and then tap Track View.
Each horizontal strip represents a track in the current sequence. MIDI tracks and audio tracks are grouped together.
MIDI tracks are listed first, audio tracks are listed second.
To move through the list of tracks, swipe up or down.
To collapse or expand each group of tracks, tap the up arrow () or down arrow () icon above the first
track’s Mute button.
The top of the screen shows the sequence name and timing information.
Use the Sequence field to select which sequence contains the tracks you want to show below.
The time counter at the top of the screen indicates the current playhead position. This is shown in most of the
modes. See General Features > Time Counter/Locate to learn about this.
148
The Settings window lets you configure certain Track View settings.
To view the Settings, tap the gear icon.
Use the Show Unused Tracks selector to turn this feature on or off. When on, tracks with a sequence, program, etc.
will still appear in the Track View. When off, only tracks with a sequence, program, etc. will appear.
To open the Timing Correct settings, tap TC at the bottom of the screen. See General Features > Timing Correct
(TC) to learn about this.
To open the metronome settings, tap Click at the bottom of the screen. See General Features > Metronome
(Click/Metro) to learn about this.
To select the previous or next track of the same type (MIDI or audio), tap Track – or Track + (respectively) at the
bottom of the screen. Alternatively, tap the track in the main part of the screen.
149
MIDI Tracks
All MIDI tracks in the project are grouped together in the upper half of the Track View.
To show or hide them, tap the  or  arrow icon.
Use the Program field to select the program that the track will use.
Use the Length field to set how long the track is. If you select the minimum value, Seq or 0 (if you use the numeric
keypad), the track will be the exact same length as its sequence.
Tip: This feature lets you maintain tracks of different lengths. For instance, you could play a 1-bar drum sequence
repeatedly under a 4-bar bass line.
Use the Velocity field to set how loudly or quietly a track plays relative to its recorded levels. When set to 50%, the
track will be played with half the velocity it was originally played. When set to 200%, the track will play twice as loud.
The maximum velocity level is still 127, though.
Use the Transpose field to set the transposition (in semitones) of the entire track.
Use the level slider to change the level of the track. The level meter above the slider shows the track’s current level.
Use the pan knob to change the panning of the track.
Use the Solo and Mute buttons to solo or mute the track (respectively).
Alternatively, tap Mute or Solo (respectively) at the bottom of the screen to mute the currently selected track.
150
Audio Tracks
All audio tracks in the project are grouped together in the lower half of the Track View.
To show or hide them, tap the  or  arrow icon.
Use the Input field to set the track’s input/inputs.
Use the Arm button to record-enable the track. When you begin audio recording, the audio signal will be recorded to
this track. You can select multiple tracks by pressing and holding Shift while tapping the Arm button to each track.
Use the Monitor button to set how your audio track will be monitored. Tapping it will cycle through its three states:
When set to Auto, you will hear incoming audio while the track is record-enabled only.
When on, you will hear incoming audio whether or not the track is record-enabled.
When off, you will never hear any incoming audio.
Use the level slider to change the level of the track. The level meter above the slider shows the track’s current level.
Use the pan knob to change the panning of the track.
Use the Solo and Mute buttons to solo or mute the track (respectively).
Alternatively, tap Mute or Solo (respectively) at the bottom of the screen to mute the currently selected track.
Use the Add new audio track button to create a new audio track.
151
Step Sequencer
The Step Sequencer lets you create or edit sequences by using the pads as “step buttons,”
simulating the experience of a traditional step-sequencer-style drum machine. This is
available for MIDI tracks only, not audio tracks.
You can also create and edit automation using the Step Sequencer. See Appendix >
Updates in v2.6 > New Features > Step Automation for more information.
To enter the Step Sequencer, do either of the following:
•
Press Menu, and then tap Step Sequencer.
•
Press Step Seq (MPC X).
The top of the screen shows the track name and information as well as sequence and timing information.
The Track field shows the name of the current track.
Use the Track Length field to set how long the track is. If you select the minimum value, Sequence or 0 (if you use
the numeric keypad), the track will be the exact same length as its sequence.
Tip: This feature lets you maintain tracks of different lengths. For instance, you could play a 1-bar drum sequence
repeatedly under a 4-bar bass line.
Use the Bars field to adjust the length of the sequence in bars.
152
Use the BPM field to adjust the tempo of the sequence.
To set whether the sequence follows its own tempo (Seq) or a master tempo (Mst), tap the
Seq/Mst button next to the BPM field. Alternatively, press Shift+Tap/Master.
The time counter at the top of the screen indicates the current playhead position. This is shown in
most of the modes. See General Features > Time Counter/Locate to learn about this.
Use the Time Division selector to set the value that determines how many steps each bar of the sequence will have.
The T indicates a triplet-based value.
Alternatively, tap TC at the bottom of the screen to open the Timing Correct window. See General Features >
Timing Correct (TC) to learn about this.
To enter or delete steps in a sequence:
1. Use the Pad –/+ buttons at the bottom of the screen to select the pad whose steps you want to enter or delete.
The current pad number is shown in the upper-left corner.
Alternatively, use the Pad Select feature: Tap and hold Pad Sel, press the desired pad, and then release Pad
Sel. You can also use Pad Select as a “latching” feature: tap Pad Sel so it is activated, press the desired pad,
and then tap Pad Sel once more so it is deactivated.
2. Use the Bar –/+ buttons at the bottom of the screen to select the bar of the sequence whose steps you want to
enter or delete. The current bar number is shown in the upper-left corner.
3. Press the pads of your MPC hardware, or tap a button at the bottom of the sequencer. Each pad corresponds to
a step in the bar and will light with a color corresponding to its velocity.
Keep in mind that for time divisions larger than 16, the bar’s steps will be represented by multiple pad banks. In
this case, use Pad Bank Buttons A and B to view all the steps within a bar.
For time divisions larger than 16, the bar’s steps will be represented by multiple pad banks. In
this case, use the left and right arrows (< and >) by the step numbers (1–16, 17–32, etc.) to
change which steps are shown in the sequencer.
Alternatively, use Pad Bank Buttons A and B.
153
To adjust the velocities of the steps, do any of the following:
•
Tap anywhere on the velocity bar of a step. The top of the velocity bar will jump to that point.
•
Use the slider on the right edge of the screen to increase or decrease the velocities of all steps.
•
Turn the Q-Link knob that corresponds to that step (the Q-Link knobs must be in the Screen edit mode).
Setting a value of 0 (Off) will delete the step.
Use the Nudge < and Nudge > arrows to shift each step left or right (respectively) one step. This is useful for
experimenting with different rhythmic permutations.
Use the slider on the right edge of the screen to increase or decrease the velocities of all steps.
Use the Flip Steps button to switch which steps have notes entered and which do not have notes.
Steps that previously had no notes will now have notes at full velocity (127). Steps that previously had
notes will now be empty.
Tap Presets to show or hide the preset sequence controls. These controls let you manipulate and
transform the velocities of the current bar in the sequence.
The first button will apply ascending or descending velocities to the steps. Each time you tap it, it will
cycle through these options:
•
The velocities will ascend to a single peak at the end of the bar.
•
The velocities will ascend to two peaks—one after each half of the bar.
•
The velocities will ascend to four peaks—one after each quarter of the bar.
•
The velocities will descend from a single peak at the start of the bar.
•
The velocities will descend from two peaks—one after each half of the bar.
•
The velocities will descend from four peaks—one at the start each quarter of the bar.
The second button will set the velocities of the steps to be at the maximum value (127) or minimum
values (1), depending on their position in the bar. Each time you tap it, it will cycle through these options:
•
The velocities of the first half of the bar will be set to 1. The velocities of the second half will be
set to 127.
•
The velocities of the first and third quarters of the bar will be set to 1. The velocities of the
second and fourth quarters will be set to 127.
•
The velocities of the first, third, fifth, and seventh eighths of the bar will be set to 1. The
velocities of the second, fourth, sixth, and eighth eighths will be set to 127.
•
The velocities of the first half of the bar will be set to 127. The velocities of the second half will
be set to 1.
•
The velocities of the first and third quarters of the bar will be set to 127. The velocities of the
second and fourth quarters will be set to 1.
•
The velocities of the first, third, fifth, and seventh eighths of the bar will be set to 127. The
velocities of the second, fourth, sixth, and eighth eighths will be set to 1.
154
The third button will apply ascending or descending velocities to the steps. Each time you tap it, it will
cycle through these options:
•
Across the entire bar, the velocities will ascend to a peak and then descend from it.
•
In each half of the bar, the velocities will ascend to a peak and then descend from it.
•
In each quarter of the bar, the velocities will ascend to a peak and then descend from it.
•
Across the entire bar, the velocities will descend from a peak into a valley and then ascend back
up to the peak.
•
In each half of the bar, the velocities will descend from a peak into a valley and then ascend back
up to the peak.
•
In each quarter of the bar, the velocities will descend from a peak into a valley and then
ascend back up to the peak.
The fourth button will swap the first half and second half of the bar. In other words, the first half of the
bar will become a mirrored image of the second half, and vice versa.
The fifth button will invert the velocities of all steps with entered notes. The sum of the old and new
velocities will equal 127. The exception is a velocity of 127 or 1 as a step with a note cannot have a
velocity of 0.
Examples:
Steps with velocities of 40 will now have velocities of 87, and vice versa.
Steps with velocities of 75 will now have velocities of 52, and vice versa.
Steps with velocities of 127 will now have velocities of 1, and vice versa.
155
XYFX Mode
XYFX Mode turns the touchscreen into an XY pad where each axis represents the range of an effect
parameter. As you move your finger on the XY pad, the current position will determine the current value
of the two parameters. You can use this mode to create interesting effect automation on your tracks.
The effect you control in XYFX Mode acts like an insert effect on that program. In fact, XYFX is the
name of the insert effect you have to load to the program before you can use this mode. Learn more
about this in General Features > Effects.
To enter XYFX Mode, do either of the following:
•
Press Menu, and then tap XYFX.
•
Press XYFX (MPC X).
When you first enter this mode in a project, you may be prompted to load XYFX to the program. Tap Insert XYFX to
do this.
Note: If you already have four insert effects loaded, you will need to clear one of the insert effect slots before doing this.
Use the XYFX Location field to select the signal to which the effects will be applied: the current program (Program)
or a master output (a stereo pair of channels: Output 1/2, Output 3/4, etc.).
The time counter in the upper-right corner the current playhead position. This is shown in most of the modes. See
General Features > Time Counter/Locate to learn about this.
The automation button indicates the global automation state. This is shown in several modes. See General Features
> Automation to learn about this.
156
Touch or move your finger on the gridded part of the screen. A marker will follow your finger to indicate the current
position. The X axis is the horizontal axis, increasing in value as you move right. The Y axis is the vertical axis,
increasing in value as you move up. Each axis is labeled with its assigned parameter.
When an effect has a beat division parameter, the current division will be highlighted as an entire column.
Effects are differently colored for easy visual distinction: beat-synchronized effects are blue, while manually
controlled effects are green.
XY Mode with a beat-synchronized effect.
While touching the XY pad, tap Latch in the lower-left corner to keep the marker on the XY pad even after you
release it. The marker will remain there until you touch another part of the XY pad or until you tap Latch again.
Use the Setup button to show or hide the Setup panel, which controls how the XY pad behaves.
Use the Preset field to select the effect you want to use in XYFX Mode.
157
XY Mode with a manually controlled effect.
Use the Attack knob to set the length of the attack phase of the envelope, which is triggered when you touch the XY
pad. In other words, this determines how long it takes the effect to fully respond to your touch.
Use the Release knob to set the length of the release phase of the envelope, which is triggered when you release the
XY pad. In other words, this determines how long it takes the effect to fully deactivate after you stopping touching
the XY pad.
Use the Wet/Dry knob to set the blend the original signal (dry) and the effect signal (wet).
The X Axis and Y Axis fields show which parameters are controlled by each axis. This varies depending on the effect
you are using.
158
Sample Edit Mode
Sample Edit Mode lets you edit samples using various functions.
To enter Sample Edit Mode, do either of the following:
•
Press Menu, and then tap Sample Edit.
•
Press Sample Edit (MPC X).
To select a sample to edit, do any of the following:
•
Use the Sample field at the top of the screen.
•
In Main Mode, tap the Project field at the top of the screen, and then double-tap a sample in the list on the
right side.
•
In the Browser, tap the Project button with the P/page icon at the bottom of the screen, and then doubletap a sample in the list on the right side.
To edit the name of the sample, tap the keyboard icon next to the name at the top of the screen, and use the
virtual keyboard that appears.
To delete the sample, tap the trash-can icon next to the name at the top of the screen. In the screen that appears,
you will see the programs that use this sample within your project. Tap Delete Sample to continue, or tap Cancel to
return to the previous screen.
159
The upper half of the screen shows the waveform. The lower half shows the editing controls.
The waveform display shows the “active” section of the sample waveform. Swipe left or right on the waveform to
move through it.
Above the waveform is the timeline, shown in Samples, Time (in seconds and milliseconds), or Beats. You can
select the measurement units you want to show in the Settings.
To zoom in or out, do any of the following:
•
When the magnifying-glass icon (in the upper-right corner) is selected, spread or pinch your fingers
(respectively) on the waveform.
•
Tap the Zoom + or Zoom – buttons (respectively) at the bottom of the screen.
•
Turn Q-Link Knob 4 (Zoom on MPC X) or the fourth Q-Link knob in the fourth column (MPC Live, MPC Touch).
To scroll through the waveform, do either of the following:
•
When the magnifying-glass icon (in the upper-right corner) is selected, swipe the waveform left or right.
•
Turn Q-Link Knob 8 (Scroll on MPC X) or the third Q-Link knob in the fourth column (MPC Live, MPC Touch).
The green marker and red marker are the start point and end point (respectively). These two points define the region
of the sample that will be played.
To move the start point or end point of the selected region, do any of the following:
•
Tap and drag its marker left or right.
•
Use the Start or End fields shown below the waveform.
•
Use the first column of Q-Link knobs (Start X1__) to adjust the start point or the second column of Q-Link
knobs (End X1__) to adjust the end point. The top-most Q-Link knobs (13 and 14) provide coarse
adjustment. The bottom-most Q-Link knobs (1 and 2) provide fine adjustment.
Tip: A recorded sample may have some silence at the beginning or end, which makes it difficult to time it correctly in
a musical context. Fix this by adjusting the start point. You can also adjust end point to remove any extra silence or
unwanted audio at the end. In addition to making your workflow easier, having a “tight,” well-edited sample can
enhance your production or performance.
You can use Sample Edit Mode in three different ways: Trim Mode, Chop Mode, or Program Mode. The options for
each mode are slightly different. Please refer to the following Trim Mode, Chop Mode, and Program Mode parts of
this chapter to learn how each works. Before using these modes, though, you may want to configure your settings—
see the following Settings chapter to do this.
160
Settings
The Settings window lets you configure certain Sample Edit Mode settings.
To view the Settings, tap the gear icon.
Use the Cue Play Mode selector to set how the cue playhead will play audio.
One Shot: Tapping Play Cue will play the entire sample from the cue playhead.
Toggle: Tapping Play Cue once will start playback from cue playhead. Tapping it once more will stop playback.
Use the Cue Preview selector to set if any audio plays as you move the cue playhead. As you move the cue
playhead through the sample waveform, you can set it to play the small part of the sample before the cue playhead
(Before), play the small part of the sample after the cue playhead (After), or not play at all (Off). You can also set this
in your overall Preferences (see General Features > Menu > Preferences > General).
Use the Slice Preview selector to set if any audio plays as you move a slice marker. As you move the slice marker
through the sample waveform, you can set it to play the small part of the sample before the slice marker (Before),
play the small part of the sample after the slice marker (After), or not play at all (Off). You can also set this in your
overall Preferences (see General Features > Menu > Preferences > General).
Use the Auto-Scroll selector to set how the screen behaves relative to the audio playhead.
Follow: Depending on the zoom setting, the waveform will scroll along in the background, keeping the audio
playhead centered.
Page: The waveform display will move to the “next page” to follow the audio playhead.
Off: The waveform display will not move at all.
These functions also apply to the sample waveform in the Grid View.
Use the Timeline Units selector to set the measurement units shown above the sample waveform. You can select
one of the following options:
Time: hours:minutes:seconds:frames
Samples: number of samples
Beats: bars:beats:ticks
161
Trim Mode
We recommend using Trim Mode to crop the start and/or ends from a sample.
To enter Trim Mode, tap the Trim/Chop button in the lower-left corner so it says Trim.
Use the Start and End fields to set the position of the start point and end point of the sample (respectively).
Alternatively, tap and drag the start (S) or end (E) marker left or right, or use the first column of Q-Link knobs (Start
X1__) to adjust the start point or the second column of Q-Link knobs (End X1__) to adjust the end point.
Trim Mode includes a loop function. When on, the region of the sample between the loop point and end point will repeat.
This is useful when trying to find an ideal spot to begin the sample. The loop cannot be earlier than the start point.
To adjust the loop point, do any of the following:
•
Use the Loop field.
•
Tap and drag the start (S) marker (if Loop Lock is on) or the loop marker (if Loop Lock is off).
•
Use the first column of Q-Link knobs (Start X1__; if Loop Lock is on) or the third column of Q-Link knobs
(Loop X1__; if Loop Lock is off). The top-most Q-Link knobs (13 and 15) provide coarse adjustment. The
bottom-most Q-Link knobs (1 and 3) provide fine adjustment.
To turn Loop Lock on or off, tap the Loop Lock button. When on, the loop point is the same as the start point.
When off, the loop point is independent from the start point and indicated by a separate loop marker.
To turn the loop function on or off, tap the Loop button to cycle between the four modes:
Off: The sample will not loop.
Forward: When the loop reaches its end point, it will start playing again from the loop point.
Reverse: When the loop reaches its end point, it will play in reverse. When it reaches the loop point again, it will
return to the end point and continue playing in reverse.
Alternating: When the loop reaches its end point, it will play in reverse. When it reaches the loop point again, it
will start playing forward again from the loop point.
To switch between Forward and off, press and hold Shift, and then tap Loop at the bottom of the screen.
Use the X-Fade button to apply a crossfade to a looping sample. See Addenda > Updates in MPC 2.3 > New
Features > Crossfade Looping for more information about this.
162
Use your MPC hardware pads to play certain parts of the selected sample:
Play Loop
13
Play to Loop
Start
14
Play from
Loop Start
15
16
Play Sample
Play Sample
(One Shot)
(Note On)
Play All
09
Play Loop
Continuous
No function
10
11
12
Play from
Start
Play to
Start
Play to
End
Play from
End
(Note On)
(Note On)
(Note On)
(Note On)
05
06
07
08
Play from
Start
Play to
Start
Play to
End
Play from
End
(One Shot)
(One Shot)
(One Shot)
(One Shot)
01
02
03
04
Play Sample (One Shot) (Pad 10) plays the sample once from the start point to the end point. Press the pad
once to play it.
Play Sample (Note On) (Pad 11) plays the sample once from the start point to the end point. Press and hold the
pad to play it, and release the pad to stop playing it. Alternatively, select the headphones icon in the upper-right
corner, and then tap and hold your finger on the waveform.
Play Loop Continuous (Pad 16) plays the sample repeatedly using the mode set by the Loop button (Forward,
Reverse, or Alternating; if the Loop button is off, the sample will loop forward repeatedly).
Play Loop (Pad 13) plays the sample repeatedly using the mode set by the Loop button (Forward, Reverse, or
Alternating; if the Loop button is off, the sample will loop forward repeatedly). Press and hold the pad to play it,
and release the pad to stop playing it.
Play to Loop Start (Pad 14) plays the part of the sample just before the loop point. Press and hold the pad to
play it, and release the pad to stop playing it.
Play from Loop Start (Pad 15) plays the sample from the loop point to the end of the sample regardless of the
end point. Press and hold the pad to play it, and release the pad to stop playing it.
Play All (Pad 9) plays the entire sample.
Pads 1–4 have the same respective functions as Pads 5–8, but Pads 1–4 play the sample part as “One Shots”
(pressing the pad once will play the entire part) while Pads 5–8 play the sample part as “Note Ons” (pressing the pad
and holding it will play the part; releasing it will stop playback):
Play from Start (Pad 1, Pad 5) plays the sample from the start point to the end point.
Play to Start (Pad 2, Pad 6) plays the part of the sample just before the start point to the start point.
Play to End (Pad 3, Pad 7) plays the part of the sample just before the end point to the end point.
Play from End (Pad 4, Pad 8) plays the part of the sample from the end point to the end of the sample.
163
Use the Tune field to transpose the sample up or down from its original pitch.
Tap From BPM to open the Edit Tuning window, which lets you tune a sample to the current sequence.
Use the Beats field to match the number of beats in the sequence.
To tune the sample to the sequence, tap Match. The Tune field will adjust automatically and close the
window. The sample is now tuned to the sequence.
To tune the sample to the sequence and adjust the sequence tempo, tap To Sequence. This is the same as
tapping Match but it also changes the sequence’s tempo to the BPM shown in the Tempo field on the right.
To close the window, tap Close.
To enter a tempo manually, use the BPM field.
To detect the tempo automatically, tap Detect. In the Edit BPM window that appears, you can do any of the following:
•
Use the BPM field to enter a tempo manually.
•
Tap Detect to detect the tempo automatically.
•
Tap Tap Tempo at the bottom of the screen at the desired rate to use it as the tempo. You can play a
sequence in the background to help with your timing.
•
Tap Close, the X, or anywhere outside the window to close it.
Note: Before detecting tempo, it is recommended that you Normalize samples for best results.
164
Use the Root Note field to set the root note of the sample. This defines which note will play the sample at its original
pitch when in a keygroup program.
To select a slice to edit, do either of the following (after you have created slices in Chop Mode):
•
Use the Slice field.
•
Turn Q-Link Knob 16 (Select Slice on MPC X) or the fourth Q-Link knob in the fourth column (MPC Live,
MPC Touch).
When Link Slices is enabled (after you have created slices in Chop Mode), changing the start point of a slice will also
change the end point of the previous slice. Similarly, changing the end point of a slice will also change the start point
of the next slice. Disable Link Slices if you are trying to create slices that use non-contiguous parts of the sample.
To enable or disable this feature, tap the Link Slices button.
Important: Link Slices must be disabled to make slices nonsequential, noncontiguous, or overlapping.
0 Snap forces start points, end points, and loop points to occur only at the waveform’s “zero-crossings.” This can
help to avoid clicks and glitches when playing a sample.
To enable or disable 0 Snap, press and hold Shift, and then tap 0 Snap at the bottom of the screen.
To enable or disable the loop function, press and hold Shift, and then tap Loop at the bottom of the screen. This
switches the loop function between Forward and off. The loop function is described earlier.
Tip: You can use Trim Mode for a specific slice of the sample, previously created and selected in Chop Mode. This
allows for a more detailed view of a single slice than in Chop Mode and gives you more options for auditioning the
slice. You can easily switch between Trim Mode and Chop Mode while doing this.
To use both Trim Mode and Chop Mode to edit a sample slice:
1. Tap Trim/Chop at the bottom of the screen so it says Chop.
2. Set all fields as desired to create your sample slices.
3. Select the desired slice.
4. Tap Trim/Chop at the bottom of the screen so it says Trim. The region you are now editing is indicated by the
normal start point and end point markers rather than slice markers.
5. Tap Trim/Chop at any time to return to Chop Mode.
165
Assigning Samples
You can assign your new sample directly to a pad from Trim Mode.
To assign a sample, tap Assign at the bottom of the screen to open the Assign Sample window.
Important: Assigning a sample to a pad in this way will replace the sample on the first layer of the pad.
If you set the Assign To field to Assign slice to a pad, the
pad will simply refer to the slice in this sample instead of
creating a new sample. This is useful for reducing clutter in
your project.
Use the Pad field to select the desired pad. Alternatively,
press the desired pad.
Use the Slice Type field to select how the pad’s layer
settings will be set when the slice is assigned to it (see
Program Edit Mode to learn more about the
parameters mentioned below):
Non-Destructive Slice: The pad’s Slice setting
will be set to the slice number.
Pad Parameters: The pad’s Slice setting will be
set to Pad. The Pad Start and Pad End will be set
to the slice’s start point and end point values, and
the Loop Position will be set to the slice’s start
point but with Pad Loop deactivated.
Use the Program field to specify the program to which
you want to add the slice.
To assign the sample, tap Do It.
To cancel the operation, tap Close, the X, or anywhere
outside the window.
166
If you set the Assign To field to Make new sample, this
will create a new sample in your project. (The original
sample will remain as it is.)
Use the Pad field to select the desired pad. Alternatively,
press the desired pad.
Check the Crop Sample box to delete the unused
parts from the sample when it’s created and assigned.
This feature is destructive, though the project will still
contain your original sample.
Leave this box unchecked to keep the unused parts of
the sample when it is created and assigned. This way,
you will still be able to edit the entire sample further
even though you are using only part of it at the moment.
Use the Program field to specify the program to which
you want to add the slice.
To assign the sample, tap Do It.
To cancel the operation, tap Close, the X, or anywhere
outside the window.
167
Processing Slices & Samples
Tap the Process button to open the Process window, where you can select an editing option for the sample.
Use the Function field to select an editing process. Double-tap it or tap Function at the bottom of the screen to
open the Function window, which displays an overview of all available editing processes.
You can use any of these functions as described below.
To return to Sample Edit Mode, tap Cancel.
To return to the Process window, tap the top of the screen.
Note: All Slice processes will affect only the part of the sample between the start point and the end point. The Sample
processes (Bit Reduce and Stereo -> Mono) will affect the entire sample regardless of its start point or end point.
The Discard process deletes the regions before the start
point and after the end point.
168
The Delete process deletes the region between the start
point and end point and closes the gap between them.
The Silence process replaces the region between the start
point and end point with silence.
The Extract process deletes the regions before the start
point and after the end point and saves it as a new sample
in your current project.
Use the Edit Name field (and the virtual keyboard that
appears) to name the new sample.
Tip: This is useful if you recorded a drum loop and wanted
to remove just a snare drum hit, a kick drum hit, etc. to use
separately in the project.
The Normalize process increases a sample’s level to the
highest level possible without distortion. This is essentially
a kind of digital gain optimization, so you do not have to
worry about excessive level settings when working with
samples with a wide range of amplitudes.
169
The Reverse process reverses the region between the
start point and end point.
The Fade In process sets a fade-in between the start point
and end point. The following types are available:
Linear fades the audio in with a linear curve—a
straight line between the start and end.
Log fades the audio in with a logarithmic curve—quickly
rising at the start and flattening out towards the end.
Exp fades the audio in with an exponential curve—
slowly rising in the beginning and growing steeper
towards the end.
The Fade Out process sets a fade-out between the start
point and end point. The following types are available:
Linear fades the audio out with a linear curve—a
straight line between the start and end.
Log fades the audio out with a logarithmic curve—
quickly rising at the start and flattening out towards the
end.
Exp fades the audio out with an exponential curve—
slowly rising in the beginning and growing steeper
towards the end.
The Pitch Shift process changes the pitch of the sample
without changing its length. This lets you set the sample’s
pitch to your sequence without affecting the sample’s
tempo or duration. You can adjust it up to 12 semitones,
up or down. Keep in mind that the audio quality may
decrease at more extreme settings.
170
The Time Stretch process lengthens or shortens the
sample without changing its pitch. This is useful for
matching the durations of two samples with different
pitches. You can enter the original tempo of the sample
and the desired tempo after processing.
Use the Beat field to set the desired value number of
beats.
Use the New Tempo field to set the new tempo. The
Ratio field will then automatically show the time
stretch factor.
Alternatively, to adjust the ratio instead, use the Ratio
field to set the desired ratio. The New Tempo field will
then change automatically based on the new time
stretch factor.
The Gain Change process raises or lowers the volume of
the sample. You can adjust it up to 18 dB, higher or lower.
This function is different than Normalize because it will
allow volumes beyond clipping level. This may be a
desired effect, but remember to watch your output level!
The Copy process saves a copy of the sample.
Use the Edit Name field (and the virtual keyboard that
appears) to name the new sample. Otherwise, the
process will add a consecutive number after the sample
name.
171
The Bit Reduce process lowers the bit resolution of a
sample, effectively reducing its degree of faithful
reproduction. You can reduce it down to 1 bit. (The sound
is similar to the Resampler effect, but Bit Reduce will
permanently alter the sample.)
Tip: Use this on drum loops to get a dirty, “old-school”
sizzle but with a digital “edge.”
Note: This process affects the entire sample regardless of
its start point or end point.
The Stereo -> Mono process converts a stereo sample to a
new mono sample and saves it as a new sample.
Use the Edit Name field (and the virtual keyboard that
appears) to name the new sample. Otherwise, the
process will add a consecutive number after the sample
name.
The following options are available:
•
Left will convert the left channel only.
•
Right will convert the right channel only.
•
Sum will combine the left and right audio channels
to a single mono channel.
Note: This process affects the entire sample regardless of
its start point or end point.
172
Chop Mode
Whereas Trim Mode crops only the start and/or end off of a sample, Chop Mode divides the sample into multiple
regions called slices. We recommend using Chop Mode when working with a long sample with different sounds
throughout (e.g., a drum loop or a long melodic or harmonic passage).
To enter Chop Mode, tap the Trim/Chop button in the lower-left corner so it says Chop.
Use the Start and End fields to set the position of the start point and end point (respectively) of the currently selected
slice. Alternatively, tap and drag the start (S) or end (E) marker left or right, or use the first column of Q-Link knobs
(Start X1__) to adjust the start point or the second column of Q-Link knobs (End X1__) to adjust the end point.
Use the selector in the lower-left corner of the screen to choose how you want to use Chop Mode:
Manual
This method lets you insert slices at locations you select.
Threshold
This method uses an adjustable detection algorithm that derives the number of slices created from the
volume levels present in the sample.
Use the Threshold field to set the threshold level. Alternatively, turn Q-Link Knob 11 (Threshold on MPC X)
or the second Q-Link knob in the third column (MPC Live, MPC Touch). The higher the selected value, the
more slices will be created.
Use the Min Time field to set the minimum length of a slice in milliseconds.
Regions
This method divides a sample into several slices of equal length.
Use the Regions field to set how many regions the sample will be divided into. Alternatively, turn Q-Link
Knob 11 (Num Regions on MPC X) or the second Q-Link knob in the third column (MPC Live, MPC
Touch). The higher the selected value, the more slices will be created.
BPM
This method divides a sample into several slices based on the tempo (beats per minute).
Use the Bars field to set how many bars are in the sample. Alternatively, turn Q-Link Knob 11 (Bars on MPC
X) or the second Q-Link knob in the third column (MPC Live, MPC Touch).
Use the Beats field to set how many beats are in each bar. Alternatively, turn Q-Link Knob 7 (Beats on MPC
X) or the third Q-Link knob in the third column (MPC Live, MPC Touch).
Use the Time Div field to set a note division. Alternatively, turn Q-Link Knob 3 (Time Div on MPC X) or the
fourth Q-Link knob in the third column (MPC Live, MPC Touch). The slice markers will be placed according
to this setting. You can select 1/4, 1/8, 1/16, or 1/32. (In most cases, you should set this parameter to 1/16.)
173
To play a slice, do either of the following:
•
Press the pad that corresponds to the slice. If your sample has more than 16 slices, use the additional pad banks.
•
When the headphones icon (in the upper-right corner) is selected, tap a slice in the waveform.
When the One Shot feature is enabled, you can press a pad once to play the entire slice. When this is disabled,
pressing the pad and holding it will play the slice; releasing it will stop playback.
To enable or disable One Shot, press and hold Shift, and then tap One Shot.
To select a slice to edit, do any of the following:
•
Use the Slice field.
•
Turn Q-Link Knob 16 (Select Slice on MPC X) or the first Q-Link knob in the fourth column (MPC Live,
MPC Touch).
•
When the headphones icon (in the upper-right corner) is selected, tap a slice in the waveform.
To add a slice at the current playhead position, tap Slice+ at the bottom of the screen. You can do this at any
point during sample playback.
To insert a slice marker during sample playback, press an unlit pad (usually Pad 1) to start playback of the
sample, and then press an unlit pad during playback to place a slice marker at each location of the playhead. (If you
press a lit pad, playback will restart from that pad’s corresponding slice marker.) The number of the pad that is lit
green is the number of the most-recently inserted slice marker. The numbers of the pads that are lit yellow are the
numbers of the slice markers that are already inserted.
To split or combine slices, tap the glue-and-scissors icon. In the Split/Combine Region screen that appears, tap
one of the following buttons:
Split: This splits the currently selected region into two equal slices.
Combine: This combines the currently selected region with the one before it.
Back: This closes the window.
174
When Link Slices is enabled, changing the start point of a slice will also change the end point of the previous slice.
Similarly, changing the end point of a slice will also change the start point of the next slice. Disable Link Slices if you
are trying to create slices that use non-contiguous parts of the sample.
To enable or disable this feature, tap the Link Slices button.
Important: Link Slices must be disabled to make slices nonsequential, noncontiguous, or overlapping.
To remove all slices from a sample, press and hold Shift and tap Clear All.
The cue playhead is useful when manually inserting slice markers. You can set its position and behavior to suit your
workflow.
Use the Cue field to adjust the position of the cue playhead. Alternatively, tap and drag the translucent marker with
the triangle ().
To play the sample from the cue playhead, tap Play Cue at the bottom of the screen.
To create a slice marker at the cue playhead position, tap Slice+ at the bottom of the screen.
To set how the cue playhead behaves, use the Settings window (described earlier).
0 Snap forces start points and end points to occur only at the waveform’s “zero-crossings.” This can help to avoid
clicks and glitches when playing a sample.
To enable or disable 0 Snap, press and hold Shift, and then tap 0 Snap at the bottom of the screen.
175
Converting or Assigning Slices
You can assign your new sample directly to a pad from Chop Mode. You can also convert it into a new program or
patched phrase.
To convert or assign a sample, press and hold Shift, and then tap Convert at the bottom of the screen to open the
Convert or Assign Slices window.
If you set the Convert To field to New [program type]
program using slices, this will create a new program and
assign the sample’s slices to its pads. The pads will simply
refer to the slices in this sample instead of creating new
samples. This is useful for reducing clutter in your project.
The new program will be named after the sample and
appended with ch.
Use the Slice Type field to select how each pad’s layer
settings will be set when the slices are assigned to them
(see Program Edit Mode to learn more about the
parameters mentioned below):
•
Non-Destructive Slice: Each pad’s Slice setting
will be set to the slice number.
•
Pad Parameters: Each pad’s Slice setting will be
set to Pad. The Pad Start and Pad End
parameters will be set to the slice’s start point and
end point values, and the Loop Pos parameter will
be set to the slice’s start point but with Pad Loop
deactivated.
Check the Create Events box to automatically create
a new track for the new program in which each pad
plays its corresponding slice in ascending sequence
by pad number.
If Create Events is checked, use the Bars field to set
how many bars the slices’ events will occupy.
To convert the sample, tap Do It.
To cancel the operation, tap Close.
176
If you set the Convert To field to New clip program, this will
create a new clip program and assign the sample’s slices to
its pads as clips. The pads will simply refer to the slices in
this sample instead of creating new samples. This is useful
for reducing clutter in your project. The new program will be
named after the sample and appended with ch.
Use the Tempo field to enter the tempo of the clips in
the new program.
Check the Create Events box to automatically create
a new track for the new program in which each pad
plays its corresponding slice in ascending sequence
by pad number.
If Create Events is checked, use the Bars field to set
how many bars the slices’ events will occupy.
To convert the sample, tap Do It.
To cancel the operation, tap Close.
If you set the Convert To field to New program with new
samples, this will create a new sample from each slice and
assign them to pads in a new program.
The new program will be named after the sample and
appended with ch. The new samples will be appended with
SI-# (where # is a consecutive number).
Check the Crop Samples box to delete the unused
parts from the sample when they are created and
assigned. This feature is destructive, though the
project will still contain your original sample.
Leave this box unchecked to keep the unused parts of
the samples when they’re created and assigned. This
way, you will still be able to edit the entire samples
further even though you are using only part of them at
the moment.
By default, this option already will create a new
program. You can uncheck the Create New Program
box to convert each slice into a sample that is placed
in the project’s sample pool but not assigned to a
program or pad.
If Create New Program is checked, check the Create
Events box to automatically create a new track in which
each pad plays its corresponding slice in ascending
sequence by pad number.
If Create Events is checked, use the Bars field to set
how many bars the slices’ events will occupy.
To convert the sample, tap Do It.
To cancel the operation, tap Close.
177
If you set the Convert To field to Assign slice to a pad,
the pad will simply refer to the slice in this sample instead
of creating a new sample. This is useful for reducing clutter
in your project.
Important: Assigning a sample to a pad in this way will
replace the sample on the first layer of the pad.
Use the Pad field to select the desired pad. Alternatively,
press the desired pad.
Use the Slice Type field to select how the pad’s layer
settings will be set when the slice is assigned to it (see
Program Edit Mode to learn more about the
parameters mentioned below):
•
Non-Destructive Slice: The pad’s Slice setting
will be set to the slice number.
•
Pad Parameters: The pad’s Slice setting will be
set to Pad. The Pad Start and Pad End will be set
to the slice’s start point and end point values, and
the Loop Position will be set to the slice’s start
point but with Pad Loop deactivated.
Use the Program field to specify the program to which
you want to add the slice.
To convert the sample, tap Do It.
To cancel the operation, tap Close.
If you set the Convert To field to Make new sample, this
will create a new sample in your project. (The original
sample will remain as it is.)
Important: Assigning a sample to a pad in this way will
replace the sample on the first layer of the pad.
Use the Pad field to select the desired pad. Alternatively,
press the desired pad.
Check the Crop Sample box to delete the unused
parts from the sample when it’s created and assigned.
This feature is destructive, though the project will still
contain your original sample.
Leave this box unchecked to keep the unused parts of
the sample when it is created and assigned. This way,
you will still be able to edit the entire sample further
even though you are using only part of it at the moment.
Use the Program field to specify the program to which
you want to add the slice.
To convert the sample, tap Do It.
To cancel the operation, tap Close.
178
If you set the Convert To field to Patched phrase, this will
create a new sample that will play based on the tempo of
your Sequence, and places it in the current project. The
patched phrase will have the same name as the original
sample but appended with pp and will use a different icon
when viewing your project information.
Use the Bars field to set how many bars long the
patched phrase is meant to be.
Processing Slices
Press and hold Shift, and then tap the Process button to open the Process window, where you can select an editing
option for the currently selected slice. (This has fewer options than Trim Mode. Unavailable ones are darkened.)
Use the Function field to select an editing process. Double-tap it or tap Function at the bottom of the screen to
open the Function window, which displays an overview of all available editing processes.
Important: Chop Mode is non-destructive: You can choose the slice/edit behavior without destroying your original
sample, giving you more control over sample playback; you can save your sliced sample and but also reuse all of the
slice data in another project. See the Program Edit Mode chapter to learn more about setting a pad to play the entire
sample, a specific slice of a sample, or a specific region of the sample (independent of its slice markers).
You can use any of these functions as described below.
To return to Sample Edit Mode, tap Cancel.
To return to the Process window, tap the top of the screen.
Note: All processes here will affect only the currently selected slice.
179
The Silence process replaces the region between the start
point and end point with silence.
The Extract process deletes the regions before the start
point and after the end point and saves it as a new sample
(with a name you enter) in your current project.
Tip: This is useful if you recorded a drum loop and wanted
to remove just a snare drum hit, a kick drum hit, etc. to use
separately in the project.
The Normalize process increases a sample’s level to the
highest level possible without distortion. This is essentially
a kind of digital gain optimization, so you do not have to
worry about excessive level settings when working with
samples with a wide range of amplitudes.
The Reverse process reverses the region between the
start point and end point.
180
The Fade In process sets a fade-in between the start point
and end point. The following types are available:
Linear fades the audio in with a linear curve—a
straight line between the start and end.
Log fades the audio in with a logarithmic curve—quickly
rising at the start and flattening out towards the end.
Exp fades the audio in with an exponential curve—
slowly rising in the beginning and growing steeper
towards the end.
The Fade Out process sets a fade-out between the start
point and end point. The following types are available:
Linear fades the audio out with a linear curve—a
straight line between the start and end.
Log fades the audio out with a logarithmic curve—
quickly rising at the start and flattening out towards the
end.
Exp fades the audio out with an exponential curve—
slowly rising in the beginning and growing steeper
towards the end.
The Pitch Shift process changes the pitch of the sample
without changing its length. This lets you set the sample’s
pitch to your sequence without affecting the sample’s
tempo or duration. You can adjust it up to 12 semitones,
up or down. Keep in mind that the audio quality may
decrease at more extreme settings.
The Gain Change process raises or lowers the volume of
the sample. You can adjust it up to 18 dB, higher or lower.
This function is different than Normalize because it will
allow volumes beyond clipping level. This may be a
desired effect, but remember to watch your output level!
181
Program Mode
Program Mode lets you edit a sample in the context of the program in which you’ll use it. You can adjust the pad
parameters as though you were in Program Edit Mode, auditioning and hearing how it will sound in the program’s
audio path.
To enter Program Mode, tap the Program button at the bottom of the screen. The pads will show their assigned
samples in the current Program.
Use the Start and End fields to set the position of the start point and end point of the sample (respectively).
Alternatively, tap and drag the start (S) or end (E) marker left or right, or use the first column of Q-Link knobs (Start
X1__) to adjust the start point or the second column of Q-Link knobs (End X1__) to adjust the end point.
Program Mode includes a loop function. When on, the region of the sample between the loop point and end point will
repeat. This is useful when trying to find an ideal spot to begin the sample. The loop cannot be earlier than the start point.
To adjust the loop point, do any of the following:
•
Use the Loop field.
•
Tap and drag the start (S) marker (if Loop Lock is on) or the loop marker (if Loop Lock is off).
•
Use the first column of Q-Link knobs (Start X1__; if Loop Lock is on) or the third column of Q-Link knobs
(Loop X1__; if Loop Lock is off). The top-most Q-Link knobs (13 and 15) provide coarse adjustment. The
bottom-most Q-Link knobs (1 and 3) provide fine adjustment.
To turn Loop Lock on or off, tap the Loop Lock button. When on, the loop point is the same as the start point.
When off, the loop point is independent from the start point.
To turn the loop function on or off, tap the Loop button to cycle between the four modes:
Off: The sample will not loop.
Forward: When the loop reaches its end point, it will start playing again from the loop point.
Reverse: When the loop reaches its end point, it will play in reverse. When it reaches the loop point again, it will
return to the end point and continue playing in reverse.
Alternating: When the loop reaches its end point, it will play in reverse. When it reaches the loop point again, it
will start playing forward again from the loop point.
To switch between Forward and off, press and hold Shift, and then tap Loop at the bottom of the screen.
182
Tap each pad to hear its sample/samples. The sample on its first layer will automatically appear in the waveform
display for editing.
Use the Tune field to transpose the sample up or down from its original pitch.
Tap From BPM to open the Edit Tuning window, which lets you tune a sample to the current sequence.
Use the Number of Beats field to match the number of beats in the sequence.
To tune the sample to the sequence, tap Match. The Tune field will adjust automatically and close the
window. The sample is now tuned to the sequence.
To tune the sample to the sequence and adjust the sequence tempo, tap To Seq. This is the same as
tapping Match but it also changes the sequence’s tempo to the BPM shown in the Tempo field on the right.
To close the window, tap Close.
Use the Root Note field to set the root note of the sample. This defines which note will play the sample at its original
pitch when in a keygroup program.
Use the Slice field to display either the sample as it has been edited (Pad) or the entire sample (All).
If the Slice field is set to All, you can display the sample as it has been edited but keep the start point and end point.
To do this, press and hold Shift, and then tap To Pad at the bottom of the screen. The Slice field will change to
Pad, but the start point and end point will remain in their current locations.
183
The Link Slices button does not have a function in Program Mode.
0 Snap forces start points, end points, and loop points to occur only at the waveform’s “zero-crossings.” This can
help to avoid clicks and glitches when playing a sample.
To enable or disable 0 Snap, press and hold Shift, and then tap 0 Snap at the bottom of the screen.
To enable or disable the loop function, press and hold Shift, and then tap Loop at the bottom of the screen. This
switches the loop function between Forward and off. The loop function is described earlier.
184
Assigning Samples
You can assign your new sample directly to a pad from Program Mode.
To assign a sample, tap Assign at the bottom of the screen to open the Assign Sample window.
Important: Assigning a sample to a pad in this way will replace the sample on the first layer of the pad.
If you set the Assign To field to Assign slice to a pad, the
pad will simply refer to the slice in this sample instead of
creating a new sample. This is useful for reducing clutter in
your project.
Use the Pad field to select the desired pad. Alternatively,
press the desired pad.
Use the Slice Type field to select how the pad’s layer
settings will be set when the slice is assigned to it (see
Program Edit Mode to learn more about the parameters
mentioned below):
•
Non-Destructive Slice: The pad’s Slice setting
will be set to the slice number.
•
Pad Parameters: The pad’s Slice setting will be
set to Pad. The Pad Start and Pad End will be set
to the slice’s start point and end point values, and
the Loop Position will be set to the slice’s start
point but with Pad Loop deactivated.
Use the Program field to specify the program to which
you want to add the slice.
To assign the sample, tap Do It.
To cancel the operation, tap Close.
If you set the Assign To field to Make new sample, this
will create a new sample in your project. (The original
sample will remain as it is.)
Use the Pad field to select the desired pad. Alternatively,
press the desired pad.
Check the Crop Sample box to delete the unused
parts from the sample when it’s created and assigned.
This feature is destructive, though the project will still
contain your original sample.
Leave this box unchecked to keep the unused parts of
the sample when it is created and assigned. This way,
you will still be able to edit the entire sample further
even though you are using only part of it at the moment.
Use the Program field to specify the program to which
you want to add the slice.
To assign the sample, tap Do It.
To cancel the operation, tap Close.
185
Processing Slices
Press and hold Shift, and then tap the Process button to open the Process window, where you can select an editing
option for the currently selected slice. (This has fewer options than Trim Mode. Unavailable ones are darkened.)
Use the Function field to select an editing process. Double-tap it or tap Function at the bottom of the screen to
open the Function window, which displays an overview of all available editing processes.
Important: Program Mode is non-destructive: You can choose the slice/edit behavior without destroying your original
sample, giving you more control over sample playback; you can save your sliced sample and but also reuse all of the
slice data in another project. See the Program Edit Mode chapter to learn more about setting a pad to play the entire
sample, a specific slice of a sample, or a specific region of the sample (independent of its slice markers).
You can use any of these functions as described below.
To return to Sample Edit Mode, tap Cancel.
To return to the Process window, tap the top of the screen.
Note: All processes here will affect only the currently selected slice.
186
The Silence process replaces the region between the start
point and end point with silence.
The Extract process deletes the regions before the start
point and after the end point and saves it as a new sample
(with a name you enter) in your current project.
Tip: This is useful if you recorded a drum loop and wanted
to remove just a snare drum hit, a kick drum hit, etc. to use
separately in the project.
The Normalize process increases a sample’s level to the
highest level possible without distortion. This is essentially
a kind of digital gain optimization, so you do not have to
worry about excessive level settings when working with
samples with a wide range of amplitudes.
The Reverse process reverses the region between the start
point and end point.
187
The Fade In process sets a fade-in between the start point
and end point. The following types are available:
Linear fades the audio in with a linear curve—a
straight line between the start and end.
Log fades the audio in with a logarithmic curve—quickly
rising at the start and flattening out towards the end.
Exp fades the audio in with an exponential curve—
slowly rising in the beginning and growing steeper
towards the end.
The Fade Out process sets a fade-out between the start
point and end point. The following types are available:
Linear fades the audio out with a linear curve—a
straight line between the start and end.
Log fades the audio out with a logarithmic curve—
quickly rising at the start and flattening out towards the
end.
Exp fades the audio out with an exponential curve—
slowly rising in the beginning and growing steeper
towards the end.
The Pitch Shift process changes the pitch of the sample
without changing its length. This lets you set the sample’s
pitch to your sequence without affecting the sample’s
tempo or duration. You can adjust it up to 12 semitones,
up or down. Keep in mind that the audio quality may
decrease at more extreme settings.
The Gain Change process raises or lowers the volume of
the sample. You can adjust it up to 18 dB, higher or lower.
This function is different than Normalize because it will
allow volumes beyond clipping level. This may be a
desired effect, but remember to watch your output level!
188
Program Edit Mode
Program Edit Mode contains all parameters for editing your Programs.
For drum programs, this mode includes the parameters of four layers as well as all synthesis parameters and insert
effect settings. See the Drum Programs section to learn more.
For keygroup programs, this mode contains slightly more parameters than drum programs. See the Keygroup
Programs section to learn more.
For clip programs, this mode looks very different from that of other programs due to how clip launching works. See
the Clip Programs section to learn more.
For plugin programs, skip to Plugin Programs to learn more.
For MIDI programs and CV programs, skip to MIDI Programs and CV Programs to learn more.
For more general information on the differences between the types of programs, please see General Features >
Programs.
To enter Program Edit Mode, do either of the following:
•
Press Menu, and then tap Program Edit.
•
Press Prog Edit (MPC X).
Drum Programs
When using drum programs, Program Edit Mode lets you edit the parameters for each pad.
To select a pad, press it. Its parameters will appear on the screen immediately.
To view a specific tab of parameters, tap the Master, Samples, Pan Velocity, Filter/Env, LFO Modulation, or
Effects button at the bottom of the screen. You can tap the Samples button multiple times to cycle through its
three available tabs.
189
Tap the location icon at the top of the screen (between the Program and Pad fields) to open the Edit Zones
window, which is a feature for drum programs and clip programs. This window displays an overview of any selected
pads. Use the Mode selector to set how the selected pads will be edited:
Current: Only the currently selected pad can be edited.
Multiple: All selected pads can be edited simultaneously.
All: All pads can be edited simultaneously.
To close the window, tap Close, the X, or anywhere outside the window.
Tip: You can immediately select multiple pads while on any tab in Program Edit Mode (regardless of the current Edit
Zones setting) by pressing and holding the Shift button and pressing each desired pad. The Edit Zones setting will
automatically change to Multiple.
190
Tap the down-arrow icon at the top of the screen (next to the Program field) to open the Flatten Pad window,
which renders all samples on a pad as an audio sample and places it on the first layer of that pad. The resulting
sample is the audio signal produced by that pad at full velocity (127) after the pad channel strip, which means that it
includes any assigned pad insert effects and the results of warping the sample.
This function is useful if you need to reduce how CPU-intensive a pad or program is by essentially “embedding” the
warping and effects in the sample itself. By default, it will use the name of the first sample. This function works for drum
programs only. (This is the same as the Flatten Pad process shown in the program editing functions in Main Mode.)
To select the pad, press it or use the Pad menu.
To set the length of the audio tail, use the Audio Tail field. This will add extra seconds to the end of the resulting
audio file. This is useful if you are using effects or samples whose sounds exceed the defined audio length (e.g.,
long reverb or delay, one-shot samples with long decays, etc.). We recommend using an audio tail of at least a
couple of seconds.
To name the new sample, tap the Edit Name field, and use the virtual keyboard that appears.
To confirm your choice, tap Do It.
To cancel, tap Cancel.
The automation button indicates the global automation state. This is shown in several modes. See General Features
> Automation to learn about this.
191
Master
In the Master tab, you can set the playback mode and tuning for the overall Program.
Polyphony sets the playback mode for the program’s pads. In Mono Mode, only one pad will sound at a time. If a
pad is played while another (or the same one) is still playing its sample/samples, the new pad will immediately mute
all other currently playing pads in that program. In Poly Mode, several pads can be triggered at the same time
(limited only by the total number of voices available).
Semi lets you transpose the program up to 36 semitones up or down.
Fine provides fine-tuning of the program up to 99 cents up or down.
Volume controls the overall volume level of the loaded sample/samples.
Pan controls the overall panning of the loaded sample/samples in the stereo field.
The Simultaneous Play section lets you set up to four pads that can be triggered by pressing one pad only. This function
is useful for triggering a stack of sounds (e.g., layered kick drums). Use each Pad field to select the desired pad.
The Mute Targets tab lets you select up to four pads (in the same program) for the currently selected pad. When the
currently selected pad is played, it will immediately silence its mute targets. Use each Pad field to select the desired
mute target.
Tips:
This feature is useful for programming realistic hi-hats, especially if only the open or closed hat should be heard.
This feature is similar to the mute group feature, available for both drum programs and keygroup programs.
192
Samples
Each pad can trigger up to four samples, which are assigned in four individual layers. Each layer has identical,
independently assignable parameters.
Tap Samples to cycle through its three available tabs.
On all three sections, you can access the Settings window, which lets you configure certain settings in the Samples tab.
To view the Settings, tap the gear icon.
To close the Settings, tap Close, the X in the upper-right corner, or anywhere outside the window.
Use the Link Slices selector to set how the start point and end point of a slice in a larger sample is set. You can
create these slices in Sample Edit Mode (Chop Mode).
When on, changing the start point of a slice will also change the end point of the previous slice. Similarly, changing
the end point of a slice will also change the start point of the next slice. Disable Link Slices if you are trying to create
slices that use non-contiguous parts of the sample. This is the same as the Link Slices button in Sample Edit Mode.
Use the Loop Lock selector to “link” or “unlink” the loop point from the start point. When on, the loop point is the
same as the start point. When off, the loop point is independent from the start point and indicated by a separate loop
marker. This is the same as the Loop Lock button in Sample Edit Mode.
Use the Zero Snap selector to enable or disable the Zero Snap feature, which forces start points, end points, and
loop points to occur only at the waveform’s “zero-crossings.” This can help to avoid clicks and glitches when playing
a sample. This is the same as the 0 Snap button in Sample Edit Mode.
193
The first Samples tab contains the sample waveform for each layer and controls for its pitch, timing, and playback.
The upper half of the screen shows the waveform of the sample on the currently selected layer. The lower half shows
the editing controls.
The waveform display shows the “active” section of the sample waveform. Swipe left or right on the waveform to
move through it.
Above the waveform is the timeline, shown in bars, beats, and ticks.
Use the bottom-most Q-Link knob in the fourth bank to zoom in or out of the sample waveform.
Tap each layer number (Layer 1–4) under the waveform to select it. When selected, its sample waveform will be
shown in the upper half of the screen and its settings will be shown in the lower half.
Use the Sample field to select the sample file for that layer. Remember that the sample has to be loaded into the project’s
sample pool beforehand. For information on how to load samples into a project, please see the Browser chapter.
Important: The parameters in the Samples tabs work in conjunction with Chop Mode (in Sample Edit Mode). Here’s
how it works:
When working in Sample Edit Mode and using Chop Mode to divide a sample into slices for your pads, you can
convert a slice using Non-Destructive Slice or Pad Parameters.
A Non-Destructive Slice will let its pad to refer to that slice when you press it; the original sample remains intact and
each slice marker is like a “bookmark” for a pad. In Program Edit Mode, you’ll see that the pad/layer to which it’s
assigned has its Slice drop-down menu set to the corresponding slice number in the original sample. Playing that
pad will cause it to refer to that slice marker like a “bookmark” instead of creating an entirely new sample of that
slice. This means that you no longer have to clutter your project with a new sample for every slice (though you can
still use this earlier method, if you prefer).
A slice converted using Pad Parameters is very similar to a non-destructive slice described above. The difference is
that in Program Edit Mode, the pads/layers they’re assigned to have their Slice drop-down menus set to Pad (instead
of the slice number), and the start and end points will correspond to the slice markers in the original sample.
194
The green/S marker and red/E marker are the start point and end point (respectively). These two points define the
region of the sample that will be played.
To move the start point or end point, do any of the following:
•
Tap and drag the S or E marker left or right.
•
Use the Start or End fields shown below the waveform.
•
Use the first bank of Q-Link knobs to adjust the start point or the second bank of Q-Link knobs to adjust
the end point. The top-most Q-Link knob provides coarse adjustment. The bottom-most Q-Link knob
provides fine adjustment.
Note: When Loop Lock is on, the loop position (as determined by the Loop field, if enabled) is the same as the
sample’s start point. When off, the loop position is independent from the start point.
Use the Loop field to determine the position where the sample’s playback will repeat when Pad Loop is activated.
Alternatively, use the third bank of Q-Link knobs to adjust the loop point. The top-most Q-Link knob provides
coarse adjustment. The bottom-most Q-Link knob provides fine adjustment.
Note: When Loop Lock is on, the loop position is the same as the sample’s start point. When off, the loop position is
independent from the start point.
Use the Slice field to select what part/parts of the sample will play:
All: The entire sample will play.
Pad: The sample will play from the Pad Start position to the Pad End position, described earlier. This also lets
you activate Pad Loop (if the Sample Play field in the LFO Modulation tab is set to Note On).
Slice 1, 2, 3, etc.: If you have sliced the sample in Chop Mode, you can select which slice will play when you
trigger the pad.
Semi lets you transpose the selected layer 36 up to semitones up or down. This will affect the length of the sample (if
Warp is off). This is the same as the Semi knob on the second Samples tab.
Fine provides fine-tuning of each layer by cents. This will affect the length of the sample (if Warp is off). This is the
same as the Fine knob on the second Samples tab.
195
Use the Reverse button to select in which direction the sample will play. When on, the sample will play in reverse.
When off, the sample will play in the normal forward direction.
Use the Pad Loop button to cycle through the available Pad Loop modes.
Important: For Pad Loop to work, you must (1) set the Sample Play field (in the LFO Modulation tab) to Note On
instead of One Shot and (2) set the Slice field (in the first Samples tab) to Pad instead of All or a slice number.
Off: The sample will not loop.
Forward: You can hold down the pad to cause that sample to repeat from the Loop Position
to the end of the sample. Release the pad to stop the repeating playback.
Reverse: You can hold down the pad to cause that sample to play in reverse, repeating from
the end of the sample to the Loop Position. Release the pad to stop the repeating playback.
Alternating: You can hold down the pad to cause that sample to play from the Loop Position to
the end of the sample and then play in reverse until it reaches the Loop Position again. This will
repeat as long as you are holding the pad down. Release the pad to stop the repeating playback.
196
Tap Warp to enable or disable warping of the sample.
When enabled, lengthening or shortening the sample (based on the BPM) will not change its pitch.
When disabled, lengthening or shortening the sample will also change its pitch and vice versa.
Use the Stretch field to set the “stretch factor,” which affects how the sample is warped (if Warp is on).
Use the BPM field to enter a tempo, which affects how the sample is warped (if Warp is on).
Tap BPM Sync to enable or disable BPM Sync.
When BPM Sync and Warp are both enabled, the sample’s BPM will be “locked” to the tempo of the sequence.
When BPM Sync is disabled but Warp is enabled, the sample will be independent of the tempo of your sequence—use
the Stretch field to lengthen or shorten a sample.
Note: The Warp algorithms are very CPU-intensive and can result in audio drop-outs during playback if used too
freely. Be mindful of how (and how often) you use the warp function. You can reduce the CPU resources required by
doing any/all of the following:
•
Avoid using extreme Stretch values.
•
Minimize the amount of pitch adjustment (e.g., the Semi and Fine parameters) of warped audio.
•
Avoid warping very small track regions.
•
Warp as few tracks or track regions as possible (i.e., reduce the number of total number of voices of the
polyphonic limit that use the Warp algorithm at a given time), especially instances where the warped regions start
at the same time.
•
Avoid rapidly triggering samples that are warped.
•
If you have warped samples used in a drum program, consider using the Flatten Pad function to consolidate the
affected pad’s layers into one audio sample (see here to learn about this). After you flatten the pad, its
sample/samples no longer need to be warped.
197
The second Samples tab contains controls for its pitch and volume level.
Semi lets you transpose the selected layer 36 up to semitones up or down. This will affect the length of the sample (if
Warp is off). This is the same as the Semi field on the first Samples tab.
Fine provides fine-tuning of each layer by cents. This will affect the length of the sample (if Warp is off). This is the
same as the Fine field on the first Samples tab.
Level lets you adjust each layer’s volume, letting you control the “balance” of the samples assigned to the pad.
198
The third Samples tab contains the control for its offset.
Use the Offset slider to determine a time offset for the sample’s playback.
Positive values (right of center): When the pad is played, playback will start immediately but at a later point in the
sample specified by the offset value.
Negative values (left of center): When the pad is played, playback will be delayed by the amount specified by the
offset value.
199
Pan Velocity
Use the pan knob to adjust the stereo placement of the respective layer.
Use the Vel Start and Vel End knobs to define the velocity range of each layer.
A range from 0 to 127 lets the layer respond to the entire velocity range which is input from the respective pad while,
for example, a range from 100 to 127 lets the layer respond only to higher velocity levels. By assigning several
samples of one instrument, you can create a realistic-sounding “multi-sample” by adjusting the velocity ranges of
each layer accordingly.
For example, you may have three samples of a drum hit with low force, medium force, and high force. You can set
each sample to a layer and set the Velocity ranges so only low velocities trigger the low-force sample, only midrange velocities trigger the medium-force sample, and only high velocities trigger the high-force sample.
200
Filter/Envelope
Use the Type field to select a filter for the selected pad. See Appendix > Glossary > Filter for an explanation of the
available filter types.
Use the Cutoff knob to set the cutoff frequency for low-pass and high-pass filter types or the center frequency for
band-pass and band-stop filter types.
Use the Reso knob to set the resonance/emphasis of the frequencies around the cutoff point.
Tip: Use values lower than 80 to give more brilliance to the sound. At values higher than 80, the sound will result in a
strong audible boost around the cutoff frequency.
Use the Env to determine the amount of influence the filter envelope has on the cutoff frequency. Higher settings will
increase the modulation of the filter by the envelope; lower settings will result in only subtle changes of the filter
Cutoff over time.
Tip: To give a sound a more distinctive attack, increase the Env setting and set low Atk and Decay values as well
as a medium-low Sust value of the Filter Envelope. This will start a sound with the filter opened and close it shortly
afterward, giving it a bright start followed by a darker sustain. String sounds, on the other hand, can sound much
more “alive” with low Env settings and a high Atk value, resulting in a slight fade-in of the higher frequencies.
Use the Modulation Sources knobs to set how much velocity is required to modulate certain other parameters:
Vel>Sta (VelocityStart) sets how much velocity is needed (for a triggered pad) to modulate the sample start point.
Vel>Atk (VelocityAttack) sets how much velocity is needed (for a triggered pad) to modulate the Attack phase
for the Amp envelope.
Vel>Env (VelocityEnvelope) enables velocity information to control the amount of the filter envelope’s effect on
the cutoff frequency.
Vel>Flt (VelocityFilter) uses the velocity of a pad to modulate the cutoff frequency directly.
201
The Filter Envelope controls affect the filter frequency. Use the fields or tap and drag the “handles” of the envelope
to shape the envelope or time-variant modulation output. Adjust the envelope’s influence on the filter frequency with
the Env knob. See the later Anatomy of an Envelope section to learn about the envelope parameters.
The Amp Envelope controls affect level changes over time. Use the fields or tap and drag the “handles” of the
envelope to shape the envelope or time-variant modulation output. Adjust the envelope’s influence on the filter
frequency with the Env knob. See the later Anatomy of an Envelope section to learn about the envelope parameters.
LFO Modulation
The Modes controls let you set the behavior for each pad’s samples in a drum program.
Use the Mute Group field to assign the selected pad to one of the 32 available groups. When pads assigned to the
same mute group receive MIDI notes, the last pad played will silence all other pads in that mute group. A mute group
affects pads within that program only; mute groups do not affect pads in other programs.
Tip: This feature is useful for programming realistic hi-hats, especially if only the open or closed hat should be heard.
Use the Layer Play selector to determine how multiple samples assigned to the same pad are played:
Cycle (Cyc): Each time the pad is played, it will play the next layer’s sample. In other words, the samples will
cycle through the layers as follows: 1, 2, 3, 4, 1, 2, 3, 4… etc.
Velocity (Vel): The pad will switch between layers depending on how hard you press a pad.
Random (Ran): Each time the pad is played, it will play one of its layer’s samples at random.
Use the Sample Play selector to determine how much of the sample is played.
One Shot: The entire sample will play from start to end. Use this when you want to play short sounds.
Note On: The sample will play only as long as the pad is held. This is better for longer samples so you can
control a sound’s duration by pressing and holding its corresponding pad.
202
Use the Pad Polyphony field to determine how the pad’s sound behaves when multiple hits are registered. When set
to Mono, only one pad will sound at a time. If a pad is played while another (or the same one) is still playing its
sample/samples, the new pad will immediately mute all other currently playing pads in that program. When set to
Poly, several pads can be triggered at the same time (limited only by the total number of voices available). You can
also select a specific number of pads (2–32) so that you can trigger up to this many pads at the same time (unless
they exceed the total number of voices available).
The Velocity Sensitivity controls determine how much the velocity affects the pitch of the sound (Pitch), the attack
of the filter envelope (Attack), the volume level of the filter envelope (Amp) and or the panning of the sound (Pan).
When you press a pad softly, only minimal modulation is applied. When you press it harder, the modulation amount
also gets stronger depending on the setting of the corresponding knob.
A low-frequency oscillator (LFO) generates a periodic waveform with an adjustable frequency and shape which can
be used for modulation purposes.
Use the Wave field to select the LFO waveform type:
Sine (best suited for smooth modulations)
Triangle (best suited for smooth modulations)
S&H (samples a random value and holds it until the next value is generated)
Saw (can generate interesting filter or volume changes)
Saw Down (can generate interesting filter or volume changes)
Square (interesting results with hard-panning modulations)
Noise (generates random values and glides)
Use the Rate field to determine the LFO frequency. At lower values, it might take some time for the LFO to complete
a cycle, while higher values will come closer to audible range.
Use the Sync field to set if the LFO’s rate is synchronized with the tempo. You can select one of several time
divisions (a . indicates a dotted note; a T indicates a triplet-based time division). When None is selected, Sync is off.
Use the Destinations sliders to determine how much the LFO affects the pitch of the sound (Pitch), the cutoff
frequency of the filter (Filter), the volume level of the sound (Amp) and panning of the sound (Pan).
203
Effects
Inserts
You can select up to four insert effects for each pad. To learn how to use insert effects, please see General Features >
Effects > Insert Effects.
To add an effect:
1. Double-tap the desired Inserts slot. A list of effects will appear.
2. Swipe up or down to move through the list.
You can tap the Type and Manufacturer buttons to sort your effects by those categories.
3. To load an effect, double-tap it, or tap Select.
To close the list, tap Close.
To remove an effect from its slot, tap the trash can icon.
To enable or disable the effect, tap the On/Off button for the slot.
To enable or disable all four insert effects, tap the All On/Off button in the upper-right corner.
204
To adjust the effect’s parameters, tap the pencil icon. Use the sliders to set the value of each parameter. These
values affect only this instance of the effect; insert effects are not global.
Sends
The audio of the pad will be routed to send effects (if you have any loaded) at their designated send levels. The return
channels will then send the audio to an assigned master output at the designated return levels.
Use the Send knobs to set the volume level of the signal the pad will route to each send effect.
Important: To set the send level, use, you have to load an effect into the corresponding send effect slot in the
Channel Mixer. See Channel Mixer > Returns to learn more how to do this. To learn about send effects, please see
General Features > Effects > Send/Return Effects.
205
Keygroup Programs
When using keygroup programs, Program Edit Mode lets you edit the parameters for each keygroup.
To select a keygroup, press a pad within that keygroup. Its parameters will appear on the screen immediately.
Alternatively, use the Keygroup field at the top of the screen.
To view a specific tab of parameters, tap the Master, Samples, Pan Velocity, Filter/Env, LFO Modulation, or
Effects button at the bottom of the screen. You can tap the Samples button multiple times to cycle through its three
available tabs.
Number of KG (keygroups) lets you create up to 128 keygroups within a keygroup program. This is useful when
working with multi-samples. For example, if you want to create a realistic piano, you can use different keygroups (e.g.,
88 for a grand piano) with every keygroup containing its own sampled note (with up to four possible velocity layers).
Tap the Keygroup field to select a keygroup to edit. You can also select All to edit all keygroups simultaneously.
Tap the piano-keys icon to edit the note range of the
current keygroup. This will open the Set Keygroup Note
Range window. This lets you restrict the key range used
for a sample’s playback. Only notes with a key number
higher or equal (Low Key) or lower and equal (High Key)
to the selected value will trigger a sound.
Tips:
Alternatively, you can set the current keygroup’s note
range by using the Lo and Hi fields under Note Range in
the Master tab.
Set the Lo parameter to A0 and the Hi parameter to C8 to
emulate the range of a standard 88-key piano.
The automation button indicates the global automation state. This is shown in several modes. See General Features
> Automation to learn about this.
206
Master
In the Master tab, you can set the playback mode and tuning for the overall program.
Polyphony sets the playback mode for the program’s keygroups. In Mono Mode, only one keygroup will sound at a
time. If a keygroup is played while another (or the same one) is still playing its sample/samples, the new keygroup will
immediately mute all other currently playing keygroups in that program. In Poly Mode, several keygroups can be
triggered at the same time (limited only by the total number of voices available).
Semi lets you tune the program up to 36 semitones up or down.
Fine provides fine-tuning of the program up to 99 cents up or down.
Transpose shifts the pitch of the MIDI notes sent to the program up to 36 semitones up or down.
KG Select (Keygroup Select) lets you select a specific keygroup for editing. This parameter works in conjunction with
the Number of KG (keygroups) parameter at the top of the screen, which lets you create up to 128 keygroups within
one keygroup program. A default keygroup program contains only one single keygroup. When you have created
more than one keygroup with Number of KG, use KG Select to select any keygroup for editing. All selects all
available keygroups of a keygroup program for simultaneous editing.
Key Track allows you to switch a sample’s automatic transposition on or off. If this is off, you will always hear the
same pitch of the sample, no matter which note is triggered by pads or a connected MIDI keyboard.
207
Level controls the overall volume level of the loaded sample/samples.
Pan controls the overall panning of the loaded sample/samples in the stereo field.
Note Range lets you restrict the key range used for a sample’s playback. Only notes with a key number higher or
equal (Lo) or lower and equal (Hi) to the selected value will trigger a sound. The settings for Lo and Hi are also shown
in the virtual keyboard in the Edit Layers section. Alternatively, tap the piano-keys icon to open the Set Keygroup
Note Range window.
Tip: Set the Lo parameter to A0 and the Hi parameter to C8 to emulate the range of a standard 88-key piano.
Semi lets you transpose the sample 36 semitones up or down, while Fine provides fine-tuning of each layer up to 99
cents up or down.
Tip: The Edit Layers section has some parameters similar to those in this section (Level, Pan, Semi, Fine, Note
Range). Remember that Key Group parameters control the overall settings for the sample, while Edit Layer
parameters control the settings for each layer (up to 4).
Use the KG Polyphony (keygroup polyphony) field to determine how the keygroup will play. When set to Mono, only
one pad will sound at a time. If a pad is played while another (or the same one) is still playing its sample/samples, the
new pad will immediately mute all other currently playing pads in that program. When set to Poly, several pads can
be triggered at the same time, limited only by the total number of voices available. You can also select a specific
number of pads (2–32) so that you can play up to this many pads at the same time (unless they exceed the total
number of voices available).
Use the Mute Group field to assign the selected pad to one of the 32 available groups. When pads assigned to the
same mute group receive MIDI notes, the last pad played will silence all other pads in that mute group. A mute group
affects pads within that program only; mute groups do not affect pads in other programs.
208
Layer Play determines how multiple samples assigned to the same pad are played:
•
Cycle (Cyc): Each time the pad is played, it will play the next layer’s sample. In other words, the samples will
cycle through the layers as follows: 1, 2, 3, 4, 1, 2, 3, 4… etc.
•
Velocity (Vel): The pad will switch between layers depending on how hard you press a pad.
•
Random (Ran): Each time the pad is played, it will play one of its layer’s samples at random.
Sample Play determines how much of the sample is played:
•
One Shot: The entire sample will play from start to end. Use this when you want to play short sounds.
•
Note On: The sample will play only as long as the pad is held. This is better for longer samples so you can
control a sound’s duration by pressing and holding its corresponding pad.
209
Samples
Each keygroup can trigger up to four samples, which are assigned in four individual layers. Each layer has identical,
independently assignable parameters.
Tap Samples to cycle through its three available tabs.
On all three sections, you can access the Settings window, which lets you configure certain settings in the Samples tab.
To view the Settings, tap the gear icon.
To close the Settings, tap Close, the X in the upper-right corner, or anywhere outside the window.
Use the Link Slices selector to set how the start point and end point of a slice in a larger sample is set. You can
create these slices in Sample Edit Mode (Chop Mode).
When on, changing the start point of a slice will also change the end point of the previous slice. Similarly, changing
the end point of a slice will also change the start point of the next slice. Disable Link Slices if you are trying to create
slices that use non-contiguous parts of the sample. This is the same as the Link Slices button in Sample Edit Mode.
Use the Loop Lock selector to “link” or “unlink” the loop point from the start point. When on, the loop point is the
same as the start point. When off, the loop point is independent from the start point and indicated by a separate loop
marker. This is the same as the Loop Lock button in Sample Edit Mode.
Use the Zero Snap selector to enable or disable the Zero Snap feature, which forces start points, end points, and
loop points to occur only at the waveform’s “zero-crossings.” This can help to avoid clicks and glitches when playing
a sample. This is the same as the 0 Snap button in Sample Edit Mode.
210
The first Samples tab contains the sample waveform for each layer and controls for its pitch, timing, and playback.
The upper half of the screen shows the waveform of the sample on the currently selected layer. The lower half shows
the editing controls.
The waveform display shows the “active” section of the clip waveform. Swipe left or right on the waveform to move
through it.
Above the waveform is the timeline, shown in bars, beats, and ticks.
Use the bottom-most Q-Link knob in the fourth bank to zoom in or out of the sample waveform.
Tap each layer number (Layer 1–4) under the waveform to select it. When selected, its sample waveform will be
shown in the upper half of the screen and its settings will be shown in the lower half.
Use the Sample field to select the sample file for that layer. Remember that the sample has to be loaded into the project’s
sample pool beforehand. For information on how to load samples into a project, please see the Browser chapter.
Important: The parameters in the Samples tabs work in conjunction with Chop Mode (in Sample Edit Mode). Here’s
how it works:
When working in Sample Edit Mode and using Chop Mode to divide a sample into slices for your pads (keygroups),
you can convert a slice using Non-Destructive Slice or Pad Parameters.
A Non-Destructive Slice will let its keygroup to refer to that slice when you press a pad in that keygroup; the original
sample remains intact and each slice marker is like a “bookmark” for a keygroup. In Program Edit Mode, you’ll see
that the layer to which it’s assigned has its Slice drop-down menu set to the corresponding slice number in the
original sample. Playing that keygroup will cause it to refer to that slice marker like a “bookmark” instead of creating
an entirely new sample of that slice. This means that you no longer have to clutter your project with a new sample for
every slice (though you can still use this earlier method, if you prefer).
A slice converted using Pad Parameters is very similar to a non-destructive slice described above. The difference is
that in Program Edit Mode, the layers they’re assigned to have their Slice drop-down menus set to Pad (instead of
the slice number), and the start and end points will correspond to the slice markers in the original sample.
211
The green/S marker and red/E marker are the start point and end point (respectively). These two points define the
region of the sample that will be played.
To move the start point or end point, do any of the following:
•
Tap and drag the S or E marker left or right.
•
Use the Start or End fields shown below the waveform.
•
Use the first column of Q-Link knobs to adjust the start point or the second column of Q-Link knobs to
adjust the end point. The top-most Q-Link knob provides coarse adjustment. The bottom-most Q-Link knob
provides fine adjustment.
Note: When Loop Lock is on, the loop position (as determined by the Loop field, if enabled) is the same as the
sample’s start point. When off, the loop position is independent from the start point.
Use the Loop field to determine the position where the sample’s playback will repeat when Pad Loop is activated.
Alternatively, use the third column of Q-Link knobs to adjust the loop point. The top-most Q-Link knob provides
coarse adjustment. The bottom-most Q-Link knob provides fine adjustment.
Note: When Loop Lock is on, the loop position is the same as the sample’s start point. When off, the loop position is
independent from the start point.
Use the Slice field to select what part/parts of the sample will play:
All: The entire sample will play.
Pad: The sample will play from the Pad Start position to the Pad End position, described earlier. This also lets
you activate Pad Loop (if the Sample Play field in the Master tab is set to Note On).
Slice 1, 2, 3, etc.: If you have sliced the sample in Chop Mode, you can select which slice will play when you
trigger the pad.
Semi lets you transpose the selected layer 36 up to semitones up or down. This is the same as the Semi knob on the
second Samples tab.
Fine provides fine-tuning of each layer by cents. This is the same as the Fine knob on the second Samples tab.
212
Use the Reverse button to select in which direction the sample will play. When on, the sample will play in reverse.
When off, the sample will play in the normal forward direction.
Use the Pad Loop button to cycle through the available Pad Loop modes.
Important: For Pad Loop to work, you must (1) set the Sample Play field (in the Master tab) to Note On instead of
One Shot and (2) set the Slice field (in the first Samples tab) to Pad instead of All or a slice number.
Off: The sample will not loop.
Forward: You can hold down the pad to cause that sample to repeat from the Loop Position
to the end of the sample. Release the pad to stop the repeating playback.
Reverse: You can hold down the pad to cause that sample to play in reverse, repeating from
the end of the sample to the Loop Position. Release the pad to stop the repeating playback.
Alternating: You can hold down the pad to cause that sample to play from the Loop Position to
the end of the sample and then play in reverse until it reaches the Loop Position again. This will
repeat as long as you are holding the pad down. Release the pad to stop the repeating playback.
213
The second Samples tab contains controls for its pitch and volume level.
Semi lets you transpose the selected layer 36 up to semitones up or down. This will affect the length of the sample (if
Warp is off). This is the same as the Semi field on the first Samples tab.
Fine provides fine-tuning of each layer by cents. This will affect the length of the sample (if Warp is off). This is the
same as the Fine field on the first Samples tab.
Level lets you adjust each layer’s volume, letting you control the “balance” of the samples assigned to the pad.
214
The third Samples tab contains the control for its offset.
Use the Offset slider to determine a time offset for the sample’s playback.
Positive values (right of center): When the pad is played, playback will start immediately but at a later point in
the sample specified by the offset value.
Negative values (left of center): When the pad is played, playback will be delayed by the amount specified by
the offset value.
215
Pan Velocity
Use the Pan knob to adjust the stereo placement of the respective layer.
Use the Vel Start and Vel End knobs to define the velocity range of each layer.
A range from 0 to 127 lets the layer respond to the entire velocity range which is input from the respective pad while,
for example, a range from 100 to 127 lets the layer respond only to higher velocity levels. By assigning several
samples of one instrument, you can create a realistic-sounding “multi-sample” by adjusting the velocity ranges of
each layer accordingly.
For example, you may have three samples of a piano key with low force, medium force, and high force. You can set
each sample to a layer and set the Velocity ranges so only low velocities trigger the low-force sample, only midrange velocities trigger the medium-force sample, and only high velocities trigger the high-force sample.
Use the Root Note menu to set the starting note of each loaded sample. Smp denotes the sample’s default pitch.
216
Filter/Envelope
Use the Type field to select a filter for the selected pad. See Appendix > Glossary > Filter for an explanation of the
available filter types.
Use the Cutoff knob to set the cutoff frequency for low-pass and high-pass filter types or the center frequency for
band-pass and band-stop filter types.
Use the Reso knob to set the resonance/emphasis of the frequencies around the cutoff point.
Tip: Use values lower than 80 to give more brilliance to the sound. At values higher than 80, the sound will result in a
strong audible boost around the cutoff frequency.
Use the Env to determine the amount of influence the filter envelope has on the cutoff frequency. Higher settings will
increase the modulation of the filter by the envelope; lower settings will result in only subtle changes of the filter
Cutoff over time.
Tip: To give a sound a more distinctive attack, increase the Env setting and set low Atk and Decay values as well
as a medium-low Sust value of the Filter Envelope. This will start a sound with the filter opened and close it shortly
afterward, giving it a bright start followed by a darker sustain. String sounds, on the other hand, can sound much
more “alive” with low Env settings and a high Atk value, resulting in a slight fade-in of the higher frequencies.
Use the Modulation Sources knobs to set how much velocity is required to modulate certain other parameters:
Kbd>Flt (KeyboardFilter) sets how much the note value will be added to the filter cutoff. This allows higher notes
to sound brighter.
Vel>Atk (VelocityAttack) sets how much velocity is needed (for a triggered pad) to modulate the Attack phase
for the Amp envelope.
Vel>Env (VelocityEnvelope) enables velocity information to control the amount of the filter envelope’s effect on
the cutoff frequency.
Vel>Flt (VelocityFilter) uses the velocity of a pad to modulate the cutoff frequency directly.
217
The Filter Envelope controls affect the filter frequency. Use the fields or tap and drag the “handles” of the envelope
to shape the envelope or time-variant modulation output. Adjust the envelope’s influence on the filter frequency with
the Env knob. See Anatomy of an Envelope to learn about the envelope parameters.
The Amp Envelope controls affect level changes over time. Use the fields or tap and drag the “handles” of the
envelope to shape the envelope or time-variant modulation output. Adjust the envelope’s influence on the filter
frequency with the Env knob. See Anatomy of an Envelope to learn about the envelope parameters.
LFO Modulation
The Velocity Sensitivity controls determine how much the velocity affects the pitch of the sound (Pitch), the attack
of the filter envelope (Attack), the volume level of the sound (Amp), and the panning of the sound (Pan).
When you press a pad softly, only minimal modulation is applied. When you press it harder, the modulation amount
also gets stronger depending on the setting of the corresponding knob.
A low-frequency oscillator (LFO) generates a periodic waveform with an adjustable frequency and shape which can
be used for modulation purposes.
Use the Wave field to select the LFO waveform type:
Sine (best suited for smooth modulations)
Triangle (best suited for smooth modulations)
S&H (samples a random value and holds it until the next value is generated)
Saw (can generate interesting filter or volume changes)
Saw Down (can generate interesting filter or volume changes)
Square (interesting results with hard-panning modulations)
Noise (generates random values and glides)
218
Use the Rate field to determine the LFO frequency. At lower values, it might take some time for the LFO to complete
a cycle, while higher values will come closer to audible range.
Use the Sync field to set if the LFO’s rate is synchronized with the tempo. You can select one of several time
divisions (a . indicates a dotted note; a T indicates a triplet-based time division). When None is selected, Sync is off.
Use the Destinations sliders to determine how much the LFO affects the pitch of the sound (Pitch), the cutoff
frequency of the filter (Filter), the volume level of the sound (Amp) and the panning of the sound (Pan).
The Controller Mod section determines the influence of additional play controllers on various sound parameters.
Important: To use these parameters, make sure that a connected MIDI device can send pitch bend messages as
well as aftertouch and modulation wheel data.
Pitch Bend sets the range (in semitones) of a connected MIDI keyboard’s pitch-bend wheel.
Wheel>LFO determines how much a connected MIDI keyboard’s modulation wheel affects the LFO intensity.
Aft>Filt (AftertouchFilter Cutoff) determines how much a connected MIDI keyboard’s aftertouch data affects the
filter cutoff.
219
Effects
Inserts
You can select up to four insert effects for each keygroup. To learn how to use insert effects, please see General
Features > Effects > Insert Effects.
Important: When using keygroup insert effects, they will be applied to that keygroup only. Keep this in mind if you
load insert effects to multiple keygroups with overlapping note ranges—the effects will overlap in that range as well.
To add an effect:
1. Double-tap the desired Inserts slot. A list of effects will appear.
2. Swipe up or down to move through the list.
You can tap the Type and Manufacturer buttons to sort your effects by those categories.
3. To load an effect, double-tap it, or tap Select.
To close the list, tap Close.
To remove an effect from its slot, tap the trash can icon.
To enable or disable the effect, tap the On/Off button for the slot.
To enable or disable all four insert effects, tap the All On/Off button in the upper-right corner.
220
To adjust the effect’s parameters, tap the pencil icon. Use the user interface or sliders to set the value of each
parameter. These values affect only this instance of the effect; insert effects are not global.
Sends
The audio of the program will be routed to send effects (if you have any loaded) at their designated send levels. The
return channels will then send the audio to an assigned master output at the designated return levels.
Use the Send knobs to set the volume level of the signal the program will route to each send effect.
You can select up to four send effects for each keygroup, but remember that they will be applied to that keygroup
only. Keep this in mind if you load insert effects to multiple keygroups with overlapping note ranges—the effects will
overlap in that range as well.
Important: To use a send effect, you have to load an effect into the corresponding send effect slot in the Channel
Mixer. See Channel Mixer > Returns to learn more how to do this. To learn about send effects, please see General
Features > Effects > Send/Return Effects.
221
Clip Programs
When using clip programs, Program Edit Mode lets you assign a sample (a loop called a clip) to each pad in a single
bank. You can also edit various settings to determine how each pad launches its assigned clip.
To select a pad, press it. Its parameters will appear on the screen immediately.
To view a specific tab of parameters, tap Program or Pad the bottom of the screen. The Program tab is
where you assign clips to pads (see Program below). The Pad tab is where you determine how each pad plays
its clip (see Pad below).
Tap the location icon at the top of the screen (between the Program and Pad fields) to open the Edit Zones
window, which is a feature for drum programs and clip programs. This window displays an overview of any selected
pads. Use the Mode selector to set how the selected pads will be edited:
Current: Only the currently selected pad can be edited.
Multiple: All selected pads can be edited simultaneously.
All: All pads can be edited simultaneously.
To close the window, tap Close, the X, or anywhere outside the window.
222
The automation button indicates the global automation state. This is shown in several modes. See General Features
> Automation to learn about this.
The Settings window lets you configure certain Audio Edit Mode settings.
To view the Settings, tap the gear icon.
Use the Auto-Scroll selector to set how the screen behaves relative to the audio playhead while viewing the Pad tab.
Follow: Depending on the zoom setting, the waveform display will scroll along in the background while keeping
the audio playhead centered.
Page: The waveform display will move to the “next page” to follow the audio playhead.
Off: The waveform display will not move at all.
These functions also apply to the Grid View, Audio Edit Mode, List Edit Mode, and Sample Edit Mode.
223
Program
This tab is where you can assign clips to each pad and adjust the program’s overall tuning and quantization.
To assign a sample to a pad, press or tap a pad to select it (it will play its assigned samples, if any). Tap the
Sample field, and then use the data dial or –/+ buttons to select a clip. Alternatively, double-tap the Sample field,
and then tap a clip to select it.
To clear the assigned clip from a selected pad, assign a sample to a pad, but select None.
Coarse lets you transpose the program up to 36 semitones up or down.
Fine provides fine-tuning of the program up to 99 cents up or down.
Use the Launch Quantize field to set the quantization of the program in bars (or subdivisions of a bar).
224
Pad
The upper half of the screen shows the clip waveform. The lower half shows the editing controls.
The waveform display shows the “active” section of the clip waveform. Swipe left or right on the waveform to move
through it.
Above the waveform is the timeline, shown in bars, beats, and ticks.
The green marker and red marker are the start point and end point (respectively). These two points define the region
of the sample that will be played.
To move the start point or end point of the selected region, do any of the following:
•
Tap and drag the S or E marker left or right.
•
Use the Start or End fields shown below the waveform.
•
Use the first row of Q-Link knobs (Layer 1 Start) to adjust the start point or the second row of Q-Link
knobs (Layer 1 End) to adjust the end point. The right-most Q-Link knobs (12 and 16) provide coarse
adjustment. The left-most Q-Link knobs (9 and 13) provide fine adjustment.
Use the Zoom + or Zoom – buttons at the bottom of the screen to zoom in or out (respectively) of the waveform.
225
Below is a brief step-by-step process so you can get familiar with setting up a clip. Continue reading the rest of this
chapter to learn how to use the parameters in this window.
To assign and edit a clip:
1. Assign a sample to a pad using the Program tab
(described earlier). For example, start with a four-bar
drum loop.
2. In the Pad tab, note that the BPM field has a value,
which is automatically detected.
If the Warp button is not already on, tap it. The Warp
function keeps the loop in time with the sequence
tempo or the master tempo.
3. If you need to edit the loop’s tempo manually, do any
of the following:
•
Tap the BPM field, and then use the data dial
or –/+ buttons to change the value.
•
Double-tap the BPM field, and then use the
numeric keyboard that appears to enter a value.
4. Let’s shorten the loop to a two-bar loop by doing any
of the following:
•
Tap and drag the start point (S) or end point (E)
marker.
•
Tap the beat, bar, or tick value of the Start or
End fields, and then use the data dial or –/+
buttons to change the value.
•
Double-tap the beat, bar, or tick value of the
Start or End fields, and then use the numeric
keyboard that appears to enter a value.
Set the locations properly to ensure the loop’s timing
is correct—neither too short nor too long. When the
loop repeats, it should feel seamless.
5. If the Fade button is not already on, tap it. This applies
a very small fade-in and fade-out at the start and end
of the clip to prevent “clicks” and glitches if start point
or end point is not at a “zero-crossing.”
6. If you need to edit the loop’s pitch manually, do any of
the following:
•
Tap the Coarse or Fine slider, and then use the
data dial or –/+ buttons to change the value.
•
Use Q-Link Knobs 1 and 2 (Layer __ Semi
Tune and Layer __ Fine Tune) to change the
value of the Coarse or Fine sliders.
•
Double-tap the Coarse or Fine slider, and then
use the numeric keyboard that appears to enter
a value.
The Coarse slider adjusts the pitch in semitones. The
Fine value adjusts the pitch in cents. You will hear the
pitch adjust in real time.
226
Tap Warp to lengthen or shorten the clip without changing its pitch, and use the BPM field to change the tempo. Use
the Coarse and Fine sliders if you want to change the pitch.
Use the Pad Play field to determine how the clip is played.
One Shot: When you press the pad, the entire clip will play from start to end and then stop.
Toggle: When you press the pad, the entire clip will play from start to end and loop indefinitely. Pressing it
again—or launching another in the same mute group—will stop its playback. This is the most common usage.
Use the Pad Quantize field to set the quantization of the pad in bars (or subdivisions of a bar). When set to Program
so it uses the same quantization as the overall program (determined by the Launch Quantize field). When set to Off,
the pad will not follow any quantization at all.
Tap Reverse to reverse the clip’s audio.
Coarse lets you transpose the pad up to 36 semitones up or down.
Fine provides fine-tuning of the pad up to 99 cents up or down.
Use the Mute Group field to assign the selected pad to one of the 32 available groups. When pads assigned to the
same mute group receive MIDI notes, the last pad played will silence all other pads in that mute group. A mute group
affects pads within that program only; mute groups do not affect pads in other programs.
By default, each column of pads is assigned to the same mute group. This means only one pad from each column
can be playing its clip at a time. You can use the Mute Group field to configure this any way you like, though.
Use the Fade button to apply a very small fade-in and fade-out at the start and end of the clip. This can help prevent
“clicks” and glitches that may occur if the start point or end point is not placed at the waveform’s “zero-crossings.”
227
Plugin Programs
For plugin programs, you will see a graphical representation of the plugin interface, or an overview of all available
plugin parameters with a slider for each.
The automation button indicates the global automation state. This is shown in several modes. See General Features >
Automation to learn about this.
Use the user interface or sliders to set the value of each parameter.
Use the six tabs at the bottom of the screen to access the available parameters.
To assign a parameter to one of the sliders, use the MPC software.
Note: To see the user guide in the MPC software and learn how to do this, click the Help menu, select MPC Help,
and select MPC User Manual.
228
MIDI Programs
For MIDI programs, you will see an overview of all available MIDI CCs with a slider for each.
Use the sliders to set the value of each parameter.
Use the six tabs at the bottom of the screen to access the available parameters.
To assign a parameter to one of the sliders, use the MPC software.
Note: To see user guide in the MPC software and learn how to do this, click the Help menu, select MPC Help, and
select MPC User Manual.
229
CV Programs
For CV programs, you will see an overview of all available CV outputs with a slider for each.
The automation button indicates the global automation state. This is shown in several modes. See General Features >
Automation to learn about this.
Use the sliders to set the value of each parameter.
Use the six tabs at the bottom of the screen to access the available parameters.
To assign a parameter to one of the sliders, use the MPC software.
Note: To see user guide in the MPC software and learn how to do this, click the Help menu, select MPC Help, and
select MPC User Manual.
230
Anatomy of an Envelope
An envelope creates a variable control signal. It can be used, for instance, to modulate the filter settings of a sound
over a given period of time.
For drum programs, use the AD/AHDS selector to select an AD or AHDS envelope. When Sample Play is set to
Note-On, it will use an ADSR envelope.
Keygroup programs always use AHDS envelopes. When Sample Play is set to Note-On, it will use an ADSR envelope.
With AHDS envelopes, the following happens when you
trigger a sample:
1. Within the period of time you have defined with the attack
(Atk), the sample volume rises to its maximum value.
2. The sample’s maximum volume will be maintained
during the Hold phase.
3. During the Decay phase, the sample’s volume will
gradually drop to the sustain level.
4. The sample’s volume will stay at the sustain level
(Sust) until the pad is released.
With AD envelopes, the following happens when you trigger
a sample:
1. Within the period of time you have defined with the attack
(Atk), the sample volume rises to its maximum value.
2. The sample’s maximum volume will be maintained until
its Decay phase, when the sample’s volume will gradually
drop to zero over the set duration. Click the Type dropdown menu to select how the decay functions:
Decay From Start: The volume will start decreasing
immediately after reaching its maximum level.
Decay From End: The maximum volume will be
maintained for a hold phase until it reaches the
decay phase.
With ADSR envelopes, the following happens when you
trigger a sample:
1. Within the period of time defined by Attack, the
sample volume rises to its maximum value.
2. During the Decay phase, the sample’s volume will
gradually drop to the Sustain level.
3. The sample’s volume will stay at the Sustain level until
the Release phrase begins.
4. The sample’s volume will drop to “zero” over the duration
set by Release.
231
List Edit Mode
List Edit Mode has some of the features of the Grid View—as well as some additional ones—but
with a different interface/workflow.
The time counter at the top of the screen indicates the current playhead position. This is shown in most of the
modes. See General Features > Time Counter/Locate to learn about this.
The clock icon at the top of the screen opens the Timing Correct window. See General Features > Timing Correct
(TC) to learn about this.
The View menu lets you select what type of events are shown in the list.
All: Select this option to show all event types.
Notes: Select this option to show only notes.
Aftertouch: Select this option to show only aftertouch messages.
Track Automation: Select this option to show only track automation events.
Program Automation: Select this option to show only program automation events.
Pitch Bend: Select this option to show only pitch bend events.
Control Change: Select this option to show only MIDI CC messages.
Program Change: Select this option to show only MIDI program change messages.
Ch Pressure: Select this option to show only channel pressure messages.
Solo/Mute: Select this option to show only solo and mute events for tracks, programs, and pads.
Other: Select this option to show other types of events not listed above, such as pad or keygroup parameters.
The automation button indicates the global automation state. This is shown in several modes. See General Features >
Automation to learn about this.
232
The Settings window lets you configure certain
List Edit Mode settings.
To view the Settings, tap the gear icon.
Use the Hitting Pad Selects All Events selector to turn the feature on or off. When On, pressing a pad will
automatically select all note events for that pad in the sequence on that track. When set to Off, pressing a pad will
simply play its sound without selecting any note events.
Use the Auto-Advance on Step Record selector to turn the feature on or off. When set to On, pressing a pad when
the track is record-armed will move the audio playhead forward by a length determined by the current Time Division
setting in the TC/Timing Correct window. When set to Off, pressing a pad when the track is record-armed will not
change the audio playhead position.
Use the Auto-Scroll selector to set how the screen behaves relative to the audio playhead.
Follow: The list will scroll along in the background while keeping the audio playhead centered.
Page: The list will move to the “next page” to follow the audio playhead.
Off: The list will not move at all.
These functions also apply to the Grid View, Audio Edit Mode, and Sample Edit Mode.
The sequence for the track will be shown as a list of events, with the following parameters:
#: This is the number of the note event.
Time: This is the position of the note event in bars, beats, and ticks. If multiple note events occur at the same
time, additional note events will be listed immediately below, but their Time values will be grayed out.
Event Type: This icon indicates the type of event (e.g., Note, Aftertouch, Track Automation, etc.). See the list
of icons below showing the different types of events.
Pad/Note: This is the pad and/or corresponding MIDI note number. For drum programs, you will see the pad
number. For keygroup programs, plugin programs, and midi programs, you will see the note.
Length: This is the length of the note event in ticks.
Velocity: This is the velocity of the note event with its corresponding color.
Mod Type: This is the type of modifier used on the note event via automation.
Value: This is the value of the modifier automation.
233
The red arrow () on the left side of the list represents the audio playhead’s current position. If your sequence is
playing, the arrow will move accordingly.
The following icons indicate the corresponding types of events:
Note
Track Mixer Automation (Volume, Pan, Mute, Solo)
Track MIDI CC Automation (0–127)
Track Parameter Automation (Aftertouch, Pitchbend, Channel Pressure, or Program Change)
Program Mixer Automation (Volume, Pan, Mute, Solo, or Send 1–4)
Program Parameter Automation (options vary based on the type of program)
Program Insert Effect Automation (options vary based on the effect)
Pad/Keygroup Mixer Automation (Level, Pan, Pad Mute, Pad Solo, or Send 1–4)
Pad/Keygroup Parameter Automation (options vary based on the type of program)
Pad/Keygroup Insert Effect Automation (options vary based on the effect)
234
To select an event, tap it.
To select multiple events, press and hold Shift and tap each event.
To insert a note event, press Rec or Overdub so the button is lit, and then press a pad. A note event will be
created at the current location using the pad you pressed. You can keep pressing additional pads, which will
continue to insert each press as a single note event in the order you pressed them (similar to a step sequencer).
Press Stop to exit this function.
Note: Depending on the Auto-Advance on Step Record setting, the current time position will either advance each time
you press a pad or remain in place. See the earlier description of Auto-Advance on Step Record to learn about this.
To edit the Pad/Note, Length, or Velocity or numeric Value of an event, tap the value to select it, and then use
the data dial or –/+ buttons to change the value. Alternatively, double-tap it and use the numeric keypad that
appears to enter a value (for Length, Velocity, or numeric Value only).
To edit the Length of an event according to your Timing Correct settings, tap the value to select it, and then
press and hold Shift and use the data dial or –/+ buttons to change the value.
To shift the Pad/Note of an event by pad bank, tap the value to select it, and then press and hold Shift and use
the data dial or –/+ buttons to change the pad bank.
To turn a Solo/Mute event on or off, tap the desired setting on the On/Off switch. Alternatively, tap the On/Off
switch to select it, and then use the data dial or –/+ buttons to change the value.
To move an event, tap it to select it, tap Nudge at the bottom of the screen, and then use the data dial or –/+
buttons to shift the event up or down. Repeat this for other events, or tap Nudge again to turn the feature off.
To move an event according to your Timing Correct settings, tap the Time value to select it, and then press and
hold Shift and use the data dial or –/+ buttons to change the value.
To play an event, tap it to select it, and then tap Play () at the bottom of the screen. This works with note events
only.
To delete an event, tap it to select it, and then tap Delete at the bottom of the screen.
235
Browser
The Browser lets you navigate your MPC hardware’s internal and external hard disks to load
samples, sequences, songs, etc. Using filter buttons and user-definable folders, you can easily
adapt it to your preferred workflow. You can also audition (preview) your samples before loading
them.
Important: You can install an additional SATA drive in your MPC hardware, allowing for even more storage space.
See Appendix > SATA Drive Installation to learn more about this.
Important: MPC X and MPC Live support read and write capability for exFAT, FAT32, NTFS, and EXT4 file systems
as well as read-only capability for HFS+ file systems. We recommend using an exFAT file system as it is the most
robust one supported by both Windows and macOS.
To show the Browser, do any of the following:
•
Press Menu and then tap Browser.
•
Press Browse (MPC X) or Shift+Menu/Browse (MPC Live, MPC Touch).
To browse for files, tap Browse in the lower-left corner. See the Browse section to learn about this.
To view the project’s sample pool and pads, tap Sample Assign in the lower-left corner. See the Sample Assign
section to learn about this.
Browse
When the Browse tab is selected, you can do any of the following:
To browse your files by location, tap Places on the left side of the screen.
Internal is the internal drive of MPC X or MPC Live.
MPC Documents is a shortcut to the MPC Documents folder on the internal drive of MPC X or MPC Live.
If you have storage devices connected to USB ports or SD card slot of MPC X, MPC Live, or your computer
(with MPC Touch), they will appear in this column, as well.
To browse your files by content, tap Content and then tap the type of file: Drums, Instruments, Clips,
Samples, Demos, or My Files (see below to learn about these content buttons).
To browse your MPC Expansions (MPC X or MPC Live only), tap Expansions (see Addenda > Updates for
MPC 2.1 > New Features > Exporting Expansions to learn how to export MPC Expansions from your computer
to your MPC X or MPC Live).
To move up one folder level, tap the folder/ icon in the upper-left corner.
To move through a list, swipe up or down, turn the data dial or use the –/+ buttons.
To select a file or folder, tap it once.
236
To enter a folder, double-tap it or tap Open in the lower-right corner. Alternatively, press the center cursor or
Enter (MPC X) or the data dial (MPC Live, MPC Touch) to enter a selected folder. You can also tap one of the
folder buttons (1–5) in the upper-right corner to jump immediately to those pre-assigned file paths (see below to
learn how to assign these file paths).
To load a selected file, double-tap it, tap Load, or press the center cursor or Enter (MPC X) or the data dial
(MPC Live, MPC Touch). If the file is a sample, it will be loaded to the project’s sample pool. If the file is a
project, it will be loaded in its entirety (you will be asked if you want to close your current project).
To load all files in a folder, select the folder (so it is highlighted in the list), press and hold Shift, and then tap
Load All in the lower-right corner.
Important: Although you can load multiple files at once, any samples you load into a project will be automatically
converted to full-quality uncompressed audio files, so they may use more storage space than they do on your
external storage device. If you are unable to load multiple files at once due to this, select fewer files and try again.
To delete a selected file or folder, press and hold Shift and then tap Delete File at the bottom of the screen.
To preview a selected sound, tap and hold Play () at the bottom of the screen.
To enable or disable the audition function and set its volume level, tap Audition at the bottom of the screen.
In the screen that appears, tap Auto to enable or disable it, and tap and drag the level slider up or down to set
the volume level. Use the Sync and Warp buttons to audition samples and loops in time with your sequence.
See Addendum > Updates in MPC 2.5 for more information. Tap Audition once more to hide the window.
To show the information for the current storage device, press and hold Shift and then tap Drive Info at the
bottom of the screen. The drive’s information will appear in a new window. Tap OK to return to the previous screen.
To format a storage device to use an exFAT file system, select it in the Browser, press and hold Shift and
then tap Format Drive at the bottom of the screen. In the window that appears, tap OK and then Format in the
next window to format the device, or tap Cancel to return to the previous screen without formatting. This
formatting process will set the device to use the exFAT file system, remove any partitions from the drive, and
erase all of its content. (Devices that are uninitialized or do not have a file system will not be recognized by the
MPC hardware and consequently cannot be formatted.)
To get the most efficient use of the Browser, set the file
paths to your favorite drive locations first. There are five
folder buttons labeled 1–5 in the upper-right corner. You
can set these to be shortcuts to five locations on your
MPC hardware’s internal drive and/or any connected
storage devices, giving you quick access to your files.
To assign the current location to a folder button, press
and hold Shift, and then tap one of the folder buttons (1–5).
Now, when you tap that folder button again, the Browser
will show that folder’s content immediately.
Use the six filter buttons to show only specific types of
files in the list below. Folders will still be shown in the list.
To show project files only, tap the P/page icon.
To show sequence files only, tap the bars icon.
To show program files only, tap the four-squares icon.
To show sample files only, tap the waveform icon.
To show all file types, tap the three-pages icon.
To show or hide MPC project folders, tap the MPC
folder icon.
237
Use the six Content buttons to show specific locations in the internal drive of MPC
X or MPC Live and filter them automatically by file type:
Drums: Tap this button to enter the Expansions/The Vault 2 folder on the
internal drive, viewing program files only.
Instruments: Tap this button to enter the Expansions/Instruments folder on
the internal drive, viewing program files only.
Clips: Tap this button to enter the Expansions/Clips folder on the internal
drive, viewing program files only.
Samples: Tap this button to enter the Expansions/The Vault 2 folder on the
internal drive, viewing sample files only.
My Files: Tap this button to enter the MPC Documents folder, viewing all files.
Splice: Tap this button to view samples synced from a paired Splice account.
See Addendum > Updates in MPC 2.5 for more information.
Sample Assign
When the Sample Assign tab is selected, you can do any of the following:
To select a program in the project, double-tap the Program field at the top of the screen. In the list that
appears, tap the desired program. Alternatively, tap the Program field and then use the data dial or the –/+
buttons to select a location.
To move through the sample pool, swipe up or down, turn the data dial, or use the –/+ buttons.
To preview a selected sound, tap and hold Play () at the bottom of the screen.
To enable or disable the audition function and set its volume level, tap Audition at the bottom of the screen.
In the screen that appears, tap Auto to enable or disable it, and tap and drag the level slider up or down to set
the volume level. Tap Audition once more to hide the window.
To assign a sample to a pad, press it or tap it on the screen so it lights green. Then, in the Sample Pool list,
tap the desired sample. Alternatively, use the data dial or –/+ buttons to select a sample, and press the center
cursor or Enter (MPC X) or the data dial (MPC Live, MPC Touch) to assign it.
To clear a sample from a pad, press it or tap it on the screen so it lights green. Then, tap Clear Pad at the
bottom of the screen.
238
Sampler
The Sampler lets you record audio samples to use in your projects.
Important: To record any audio, you need to connect an audio source to your MPC hardware
or to your computer’s audio interface.
To open the Sampler, do either of the following:
•
Press Menu and then tap Sampler.
•
Press Sampler (MPC X).
To set up the Sampler before recording:
1. Make sure to reduce the volume levels of your audio source and speakers, headphones, and/or monitors before
you make any connections to avoid “pops” or feedback.
2. Connect a synthesizer or other line-level audio source to the input/inputs of your MPC hardware.
3. Turn the 3/4 Rec Gain (MPC X) or Rec Vol (MPC Live, MPC Touch) knob to set the input level while playing your
audio source. You should now see the level in the meter. Make sure it does not exceed the maximum level (the
meter should not be “peaking” constantly).
4. Set the recording controls as desired (described in this chapter).
5. Tap the Arm button to record-arm the Sampler.
You can use the Sampler to record using four different methods: Sample, Slice, Pad Tap, or Pad Hold, all described
later in this chapter. The following controls are present regardless of which method you use.
The Sampler page also contains the Auto Sampler, which lets you capture and convert any plugin preset or external
instrument preset into a Keygroup sampler patch. See Addenda > Updates in MPC 2.3 > New Features > Auto
Sampler for more information.
The time counter in the upper-right corner shows the current playhead position. This is shown in most of the modes.
See General Features > Time Counter/Locate to learn about this.
239
The upper-left Input Source field defines whether you are going to record an external
audio signal, which you can set to a pair of inputs (Input 1,2–3,4 in Standalone Mode,
Input 1,2–31,32 in Controller Mode) or a single input (Input 1–4 in Standalone Mode,
Input 1–32 in Controller Mode). You can also select an internal signal from within your
MPC hardware (Resample L, Resample R, or Resample L+R).
Resampling does not require an audio connection because the source is internal and is
therefore recorded without any loss in audio quality. You can, for example, use Resample
to record two or more samples by pressing the corresponding pads simultaneously.
Use the second upper-left Mono/Stereo field to choose whether your recorded
samples will be monaural (Mono) or binaural (Stereo).
The Inserts field shows any enabled or disabled effects for the Sampler. Tap the area
under Inserts to open a window where you can load, change, and enable or disable the
effects.
Important: These effects are applied to the audio as you record it. This means that the
effects cannot be “removed” from the sound later. Learn more about how effects work
in General Features > Effects.
Tap the Monitor button to enable or disable input monitoring. When on, the audio you
hear in your headphones will be taken before it reaches the Sampler, ensuring zero
latency. When off, the audio you hear in your headphones will be taken after it is
processed in the Sampler, so there may be some latency, but you will hear the audio
source as it sounds in the recording.
Tip: To avoid possible clicks or feedback while input monitoring, reduce the level of
the audio sources.
Use the threshold slider to adjust the threshold. Alternatively, turn Q-Link Knob 1
(MPC X) or the first Q-Link knob in the fourth column (MPC Live, MPC Touch).
When the Sampler is record-armed, it automatically starts recording when the level of
the incoming source exceeds this setting. If you set it too high, the recording may not
start when you play the input source, or the start of the material you wanted to record
may be missing. If you set it too low, the recording may start too early, before you play
the external source. Set this parameter to an appropriate level using the level meter.
To reset the “peak hold,” which shows the highest level of your input signal in the level
meter, tap it.
240
For reference, the Sample Length counter shows you the length of your sample during
the recording procedure.
Tap Arm to record-arm the Sampler. The button will then change to Record and show
Waiting for signal.
At that point, start recording by doing either of the following:
•
Start performing so that the incoming audio level exceeds the level of the
threshold slider.
•
Tap Record under the Sample Length counter.
To disarm the track instead, tap Cancel.
Use the Max Length field to define the maximum sampling time. Alternatively, turn the
Q-Link Knobs 3 and 4 (MPC X) or the third and fourth Q-Link knobs in the fourth
column (MPC Live, MPC Touch): Minutes and Seconds.
You can record up to 19 minutes and 59 seconds (19:59) per sample. We recommend
setting these to values that roughly match your estimated recording duration.
241
Sample
Using this method, you can insert slice markers directly in your sample as you record it.
Slice markers divide the sample into multiple regions called slices, which you can adjust in the Chop Mode of
Sample Edit Mode (see Sample Edit Mode > Chop Mode for more information). This is useful when working with a
long sample with different sounds throughout (e.g., a drum loop or a long melodic or harmonic passage).
To start recording, do one of the following:
•
Start performing so that the incoming audio level exceeds the level of the threshold slider.
•
Tap Record under the Sample Length counter.
To insert a slice marker in a sample while recording, tap Slice+ (in the lower-right corner) as the sample records.
Each time you tap it, a slice marker will be placed at that location.
To stop recording, tap Stop under the Sample Length counter.
242
After you stop your recording, the Keep or Discard Sample window will appear.
Use the Edit Name field to name the new sample. Tap it and use the virtual keyboard that appears.
Use the Program field to assign the new sample to a program. Select <none> if you want to save it to the project
without assigning it to a program.
Use the Assign to Pad field to assign the sample to a pad in the program.
Use the Root Note field to set where the sample’s original pitch will be on the keyboard.
If you recorded a sample while a sequence was playing, the Keep or Discard Sample window will show a few more
options after you select a pad.
Check the Add Event box to automatically add the sample to the currently playing sequence.
Use the @ field to select where you want the event to start:
•
Start: The sample will be a note event at the start of the currently playing sequence.
•
Trigger: The sample will be a note event where you began recording it in the currently playing sequence.
Use the Track field to set which track will contain the new event.
To confirm your selections, tap Keep at the bottom of the screen.
To discard the recording and return to the Sampler, tap Discard at the bottom of the screen.
To play the recording, tap Play at the bottom of the screen.
Tip: We recommend editing your recorded sample in Sample Edit Mode (see Sample Edit Mode for more information).
243
Slice
Using this method, the pads correspond to slices of the currently recorded sample. Slice markers divide the sample
into multiple regions called slices, which you can adjust in the Chop Mode of Sample Edit Mode (see Sample Edit
Mode > Chop Mode for more information). This is useful when working with a long sample with different sounds
throughout (e.g., a drum loop or a long melodic or harmonic passage).
To start recording, do one of the following:
•
Start performing so that the incoming audio level exceeds the level of the threshold slider.
•
Tap Record under the Sample Length counter.
To insert a slice marker in a sample while recording, press any pad as the sample records. Each time you press
it, a slice marker will be placed at that location.
The number of the pad that flashes red is the number of the slice marker that will be inserted next. The numbers of
the pads that are lit yellow are the numbers of the slice markers that are already inserted.
When you are done recording, you can name the sample and create a new program using the slices.
To stop recording, tap the round Stop button.
After you stop your recording, the Keep or Discard Sample window will appear.
Use the Edit Name field to name the new sample. Tap it and use the virtual keyboard that appears. Otherwise, the
process will add a consecutive number after the sample name.
244
Use the Create New Program field to assign the new sample to a new program:
Off: No program will be created. The slices will still be added to your project’s sample pool.
With Non-Destructive Slices: In the new program, each pad’s Slice setting will be set to the corresponding
slice number. This is identical to how you can assign samples in Sample Edit Mode (as described in Sample Edit
Mode > Chop Mode > Converting or Assigning Slices).
With Pad Parameters: In the new program, each pad’s Slice setting will be set to Pad. The Pad Start and Pad
End will be set to the slice’s start point and end point values, and the Loop Position will be set to the slice’s
start point but with Pad Loop deactivated. This is identical to how you can assign samples in Sample Edit Mode
(as described in Sample Edit Mode > Chop Mode > Converting or Assigning Slices).
To confirm your selections, tap Create or Keep at the bottom of the screen.
To discard the recording and return to the Sampler, tap Discard at the bottom of the screen.
To play the recording, tap Play at the bottom of the screen.
Tip: We recommend editing your recorded sample in Sample Edit Mode (see Sample Edit Mode for more information).
Pad Tap
Important: This mode works for drum programs only; you must select a drum program before using this mode.
Otherwise, this feature will not do anything, even though it may appear to work.
With this method, pressing a pad immediately starts or continues recording directly to that pad (make sure you are
using the desired program before you start recording). Pads with assigned samples are lit bright yellow. Pads
without samples are lit dim yellow.
To start recording to a pad, press it. Recording will start immediately, and the pad will flash red. If you press a new
pad, the recording will stop on the previous pad, which will turn green, and start on the new pad, which will flash red.
Note: If you start recording by tapping Record under the Sample Length counter—or if the volume exceeds the
level of the threshold slider—the sample will record to your project’s sample pool, not to a pad.
To stop recording to a pad, press the currently recording pad, which is flashing red. The sample will continue
recording. You can start recording on another pad at any time.
To stop all recording, tap Stop under the Sample Length counter.
When you are done recording, each pad that you have pressed during recording:
•
will have its Slice setting set to Pad;
•
will have its Pad Start and Pad End set to the slice’s start point and end point values; and
•
will have its Loop Position set to the slice’s start point but with Pad Loop deactivated.
This is identical to how you can assign samples in Sample Edit Mode (as described in Sample Edit Mode > Chop
Mode > Converting or Assigning Slices).
Tip: We recommend editing your recorded sample in Sample Edit Mode (see Sample Edit Mode for more information).
245
Pad Hold
Important: This mode works for drum programs only; you must select a drum program before using this mode.
Otherwise, this feature will not do anything, even though it may appear to work.
With this method, pressing and holding a pad immediately starts or continues recording directly to that pad (make sure
you are using the desired program before you start recording). Pads with assigned samples are lit bright yellow. Pads
without samples are lit dim yellow.
To start recording to a pad, press and hold it. Recording will start immediately, and the pad will light red.
Note: If you start recording by tapping Record under the Sample Length counter—or if the volume exceeds the
level of the threshold slider—the sample will record to your project’s sample pool, not to a pad.
To stop recording, release the pad. The pad will light green, and the sample will continue recording. You can start
recording on another pad at any time.
To stop all recording, tap Stop under the Sample Length counter.
When you are done recording, each pad that you have pressed during recording:
•
will have its Slice setting set to Pad;
•
will have its Pad Start and Pad End set to the slice’s start point and end point values; and
•
will have its Loop Position set to the slice’s start point but with Pad Loop deactivated.
This is identical to how you can assign samples in Sample Edit Mode (as described in Sample Edit Mode > Chop
Mode > Converting or Assigning Slices).
Tip: We recommend editing your recorded sample in Sample Edit Mode (see Sample Edit Mode for more information).
Auto Sampler
See Addenda > Updates in MPC 2.3 > New Features > Auto Sampler for more information.
246
Looper
The Looper lets you record and overdub audio in real time—a great tool for live performance
as well as spontaneous moments in the studio. You can export the loop as a sample to use in
your project.
To open the Looper, do either of the following:
•
Press Menu, and then tap Looper.
•
Press Shift+Sampler/Looper (MPC X).
Below is a brief step-by-step process so you can get started quickly. Continue reading the rest of this chapter to
learn how to use the Looper in different cases.
To get started using the Looper:
1. Make sure to reduce the volume levels of your audio source and speakers/headphones/monitors before you
make any connections to avoid “pops” or feedback.
2. Connect a synthesizer, audio player, etc. to the input/inputs of your MPC hardware.
3. Turn the 3/4 Rec Gain (MPC X) or Rec Vol (MPC Live, MPC Touch) knob to set the input level while playing your
audio source. You should now see the level in the meter. Make sure it does not exceed the maximum level (the
meter should not be “peaking” constantly).
4. Set the recording controls as desired (described in this chapter).
5. Tap the Record To selector so Overdub is selected.
6. Tap the Rec/Record button in the lower-right corner to record-arm the Looper.
7. Play your audio source. The Looper will start recording immediately when the input level reaches the threshold
value. Alternatively, tap /Play at the bottom of the screen to manually start recording.
Each time the Looper repeats, its contents are being overdubbed—a new layer of audio will be added each time
you let the Looper repeat as it records.
Tip: You can record a loop while playing a sequence in the background for reference.
8. To stop recording, tap /Play at the bottom of the screen.
To export your loop as a sample, tap Export to open the Keep or Discard Sample window.
To clear the contents of the Looper, tap Clear.
247
The time counter at the top of the screen indicates the current playhead position. This is shown in most of the
modes. See General Features > Time Counter/Locate to learn about this.
The upper-left Input Source field defines whether you are going to record an external
audio signal, which you can set to a pair of inputs (Input 1,2–3,4 in Standalone Mode,
Input 1,2–31,32 in Controller Mode) or a single input (Input 1–4 in Standalone Mode,
Input 1–32 in Controller Mode). You can also select an internal signal from within your
MPC hardware (Resample L, Resample R, or Resample L+R).
Resampling does not require an audio connection because the source is internal and is
therefore recorded without any loss in audio quality. You can, for example, use Resample
to record two or more samples by pressing the corresponding pads simultaneously.
Use the second upper-left Mono/Stereo field to choose whether your recorded loop
will be monaural (Mono) or binaural (Stereo).
The Inserts field shows any enabled or disabled effects for the Looper. Tap the area under
Inserts to open a window where you can load, change, and enable or disable the effects.
Important: These effects are applied to the audio as you record it. This means that the
effects cannot be “removed” from the sound later. Learn more about how effects work
in General Features > Effects.
Tap the Monitor button to enable or disable input monitoring.
When on, the audio you hear in your headphones will be taken before it reaches the Looper, ensuring zero latency.
You can turn input monitoring on only if the Input Source field is set to an input, not to a Resample setting.
When off, the audio you hear in your headphones will be taken after it is processed in the Looper, so there may
be some latency, but you will hear the audio source as it sounds in the recording.
Tip: To avoid possible clicks or feedback while input monitoring, reduce the level of the audio sources.
Use the threshold slider to adjust the threshold. Alternatively, turn Q-Link Knob 1 (Threshold on MPC X) or the first QLink knob in the fourth column (MPC Live, MPC Touch). The threshold slider will work only when Sync is off (see below).
When the Looper is record-armed, it automatically starts recording when the level of the incoming source exceeds
this setting. If you set it too high, the recording may not start when you play the input source, or the start of the
material you wanted to record may be missing. If you set it too low, the recording may start too early, before you play
the external source. Set this parameter to an appropriate level using the level meter.
To reset the “peak hold,” which shows the highest level of your input signal in the level meter, tap it.
248
Use the Bars field to define the length of your loop. Regardless
of how much or how little audio you record, this is how long
your loop will be.
Use the Sync button to sync or un-sync the looper with
sequence playback. When on, the Looper will stay in step with
your current sequence. When you play or record into the Looper,
it will wait until the sequence starts playing Bar 1 to start.
Use the Record To selector to determine the loop recording
behavior:
Play: Before recording, you must first tap the /Play button
on the screen, which will start playing the Looper.
Overdub: Before recording, you must first tap the
Rec/Record button in the lower-right corner to record-arm
the Looper.
Use the Output Gain slider to set the output signal level of the
Looper.
249
To record with the Looper:
Important:
To record without erasing any audio you’ve already recorded in the loop, use the Overdub button.
To overwrite the audio you’ve already recorded, use the Replace button.
If Record To is set to Play:
To start recording, tap the Replace or Overdub button as the loop is playing. The Looper will start recording
immediately.
To stop recording, tap the Replace or Overdub button. The Looper will stop recording but continue playing.
To stop playback and recording, tap the /Play button.
If Record To is set to Overdub:
To start recording, tap the /Play button on the screen.
If Sync is off, you can also play your audio source so that the input level reaches the threshold value.
If Sync is on, you can also press the Play or Play Start button to start playing a sequence; recording will
start when the sequence starts on Bar 1.
To stop recording, tap Overdub. The Looper will stop recording but continue playing.
To stop playback and recording, tap the /Play button, or press Stop to stop sequence playback.
To play or stop the loop (without recording), tap the /Play button on the screen.
To reverse loop playback, tap Reverse. If Sync is on, playback will reverse once the Looper’s playhead reaches
the end of the loop. If Sync is off, playback will reverse immediately.
To erase the loop immediately, tap Clear.
250
To export the loop as a sample:
1. Tap Export to open the Export Loop as a Sample window.
2. Tap the Edit Name field and use the virtual keyboard that appears to enter a new name.
3. Optional: Use the Program field to assign it directly to a program. To ignore this feature, select <none>.
4. Optional: If you’re assigning the sample to a program, use the Assign to Pad field to assign it to a specific pad.
Alternatively, just press the pad. To ignore this feature, select Off.
5. Use the Root Note field to select the sample’s root note.
6. Optional: Tap and hold your finger on Play to play the sample.
7. Tap Do It to confirm your choice, or Cancel to cancel.
When your loop is done exporting, it will be added to your project’s sample pool with the name you entered and
will be assigned to the program and pad you selected (if any).
251
Pad Mixer
In the Pad Mixer, you can set a program’s levels, stereo panning, routing, and effects.
This mode appears differently for each type of program:
For drum programs, this mode shows a pad with controls for each individual pad (of 128).
For keygroup programs, this mode shows a pad with controls for each individual keygroup (up to 128).
For clip programs, this mode shows a pad with controls for each individual clip (up to 16). Even though you can
view other pad banks, only Pad Bank A is relevant for clip programs.
For MIDI programs, plugin programs, and CV programs, this mode is unavailable.
For more information on how these programs differ, please see General Features > Programs.
To enter the Pad Mixer, do either of the following:
•
Press Menu, and then tap Pad Mixer.
•
Press Pad Mixer (MPC X).
The Pad Mixer works like an audio mixer with various settings for each pad, shown in a 4x4 array. All of their
functionality is identical. If a sample has been assigned to a pad, its name is displayed at the top of it.
To select a pad, press its corresponding pad or tap it on the screen. Alternatively, use the numbered Pad field in
the upper-left corner.
To view more channels, use the Pad Bank buttons.
252
Use the Program field in the upper-left corner to select the program whose pads you want to view. Remember that
only drum programs, keygroup programs, or clip programs will display properly in the Pad Mixer.
Use the Track field at the top of the screen to select the desired track.
The time counter in the upper-right corner the current playhead position. This is shown in most of the modes. See
General Features > Time Counter/Locate to learn about this.
The automation button indicates the global automation state. This is shown in several modes. See General
Features > Automation to learn about this.
To view a specific setting on all channels, tap the Level, Pan, Mute, Send, Insert, or Route button at the bottom
of the screen. You can tap the Send or Insert buttons multiple times to cycle through the four available slots for each.
When a pad is selected, you can view and adjust all of its settings in the left side of
the screen rather than using the tab buttons at the bottom.
When viewing the channel strip:
The first field shows the current pad number. Press a pad or double-tap the
field to select a different pad.
The second field shows where the pad is routed, which you can change:
Program (the usual setting); Out 1,2–7,8, Out 1–8 or Sub 1–8 in Standalone
Mode; and Out 1,2–31,32 or Out 1–32 in Controller Mode.
Note: When set to a mono channel, the left and right channels are summed
post-pan knob. If the pan knob is set to the center position, the left and right
channels will be summed and padded. If the pan knob is set to the maximum
left or right positions, only the respective channel will be sent to the output.
The Inserts field shows any enabled or disabled effects for that pad. Tap the
area under Inserts to open a window where you can load, change, and enable
or disable the effects.
Tap Solo or Mute to solo or mute the pad (respectively).
Adjust the pan knob or level slider to change the panning or level of the pad.
253
Levels
When the Level tab is selected, use the data dial or –/+ buttons to adjust the level of the currently selected pad.
The level sliders and meters in each pad show a visual representation of the level. Double-tap a pad on the screen to
open a large version of the level slider and meter.
Panning
When the Pan tab is selected, use the data dial or –/+ buttons to adjust the panning of the currently selected pad.
The pan sliders in each pad show a visual representation of the level. Double-tap a pad on the screen to open a large
version of the pan knob.
254
Mute
When the Mute tab is selected, mute the currently selected pad by doing any of the following:
•
Turn the data dial.
•
Use the –/+ buttons.
•
Tap the pad on the screen.
When a pad is muted, its M button will light red.
Send Effects
When the Send tab is selected, use the data dial or –/+ buttons to adjust the send level of the currently selected pad.
The level sliders in each pad show a visual representation of the level. Double-tap a pad on the screen to open a
large version of the level slider.
You can select up to four send effects for each pad. You can use various effects included in your MPC hardware as
well as other VST and AU plugins installed on your computer. Tap the Send button to cycle through the four available
slots for each.
To learn how to use send effects, please see General Features > Effects > Send/Return Effects.
Important: To use a send effect, you have to load an effect into the corresponding send effect slot in the Channel Mixer.
255
Insert Effects
When the Insert tab is selected, use the data dial or –/+ buttons to open a window where you can select an effect
for the currently selected pad.
Instead of level sliders, there are fields that display 0–4 boxes to indicate which insert slots have a loaded effect.
The level meters in each pad show a visual representation of the level. Double-tap a pad on the screen to open a
window where you can load, change, and enable or disable the effects for all four insert slots.
You can select up to four insert effects for each pad. You can use various effects included in your MPC hardware as
well as other VST and AU plugins installed on your computer. Tap the Insert button to cycle through the four available
slots for each.
To learn how to use insert effects, please see General Features > Effects > Insert Effects.
Important:
When using keygroup insert effects, they will be applied to that keygroup only. Keep this in mind if you load insert
effects to multiple keygroups with overlapping note ranges—the effects will overlap in that range as well.
If a routing is set to anything other than Program, then a program insert effect will not be applied to that pad or keygroup.
Routing
When the Route tab is selected, use the data dial or –/+ buttons to select the output of the currently selected pad.
Usually, this is set to Program. Double-tap a pad on the screen to select a different destination: Out 1,2–7,8, Out
1–8 or Sub 1–8 in Standalone Mode; and Out 1,2–31,32 or Out 1–32 in Controller Mode.
Note: When set to a mono channel, the left and right channels are summed post-pan knob. If the pan knob is set to
the center position, the left and right channels will be summed and padded. If the pan knob is set to the maximum
left or right positions, only the respective channel will be sent to the output.
256
Channel Mixer
In the Channel Mixer, you can set levels, stereo panning, and other settings for your tracks,
programs, returns, submixes and masters.
To open the Channel Mixer, do either of the following:
•
Press Menu, and then tap Channel Mixer.
•
Press Ch. Mixer (MPC X).
The Channel Mixer works like an audio mixer with various settings for each channel, shown in a 4x4 array. Their
functionality is mostly identical. The name of the track, program, or channel is displayed at the top of each one.
Use the Mixer field at the top of the screen to select which mixer you want to view: MIDI Tracks, Audio Tracks,
Programs, Returns, Submixes, or Masters. Each page has slight differences, described in each section.
The following controls and tabs are available for all of the mixers (or most of them, as indicated).
To select a channel, tap its corresponding pad on the screen. Alternatively, use the field in the upper-left corner.
To view more channels (while viewing tracks or programs), use the –/+ buttons at the top of the screen.
The time counter in the upper-right corner the current playhead position. This is shown in most of the modes. See
General Features > Time Counter/Locate to learn about this.
The automation button indicates the global automation state. This is shown in several modes. See General Features
> Automation to learn about this.
257
Levels
When the Level tab is selected, use the data dial or –/+ buttons to adjust the velocity level or volume level of the
currently selected track, program, return, submix, or master.
The level sliders and meters in each pad show a visual representation of the level. Double-tap a pad on the
screen to open a large version of the level slider and meter.
Panning
When the Pan tab is selected, use the data dial or –/+ buttons to adjust the panning of the currently selected
track, program, return, submix, or master.
The pan sliders in each pad show a visual representation of the level. Double-tap a pad on the screen to open a
large version of a pan knob.
Mute/Solo/Rec Arm
Tap this tab to cycle it through Mute, Solo, and Rec Arm functions.
When Mute is selected, mute tracks, programs, returns, submixes, or masters by doing any of the following:
•
Turn or press the center cursor or Enter (MPC X) or the data dial (MPC Live, MPC Touch).
•
Use the –/+ buttons.
•
Tap the pad on the screen.
•
Turn each of the Q-Link knobs to mute or unmute each of the pads.
When a track, program, return, submix, or master is muted, its M button will light red.
When Solo is selected, solo tracks, programs, returns, submixes, or masters by doing any of the following:
•
Turn or press the center cursor or Enter (MPC X) or the data dial (MPC Live, MPC Touch).
•
Use the –/+ buttons.
•
Tap the pad on the screen.
•
Turn each of the Q-Link knobs to solo or unsolo each of the pads.
When a track, program, return, submix, or master is soloed, its S button will light green while other tracks are
muted with their M buttons lit red.
The Solo tab is available for tracks and programs only.
When Rec Arm is selected, record-enable audio tracks by doing any of the following:
•
Turn or press the center cursor or Enter (MPC X) or the data dial (MPC Live, MPC Touch).
•
Use the –/+ buttons.
•
Tap the pad on the screen. Press and hold Shift while tapping a pad on the screen to record-enable
multiple tracks at once.
•
Turn each of the Q-Link knobs to record-arm or disarm each of the pads.
The Rec Arm tab is available for audio tracks only.
258
Send Levels (audio tracks, programs, and submixes only)
When the Send tab is selected, use the data dial or –/+ buttons to adjust the send level of audio tracks,
programs, or submixes.
The level sliders in each pad show a visual representation of the level. Double-tap a pad on the screen to open a
large version of the level slider.
You can use up to four send channels. Tap Send to cycle through the four available slots for each.
To learn how to use send effects, please see General Features > Effects > Send/Return Effects.
Important: When using send channels, make sure you have already loaded at least one effect to it using the
return mixer. See Returns below to learn how to do this.
Insert Effects (audio tracks, programs, returns, submixes, and masters only)
When the Insert tab is selected, use the data dial or –/+ buttons to open a window where you can select an
effect for the currently selected audio track, program, return, submix, or master.
Instead of level sliders, there are fields that display 0–4 boxes to indicate which insert slots have a loaded effect.
The level meters in each pad show a visual representation of the level. Double-tap a pad on the screen to open a
large version of the level slider.
You can select up to four insert effects for each audio track, program, return, submix, or master. Tap the Insert
button to cycle through the four available slots for each.
To learn how to use insert effects, please see General Features > Effects > Insert Effects.
Routing (audio tracks, programs, returns, and submixes only)
When the Route tab is selected, use the data dial or –/+ buttons to select the output of the currently selected
program, return, or submix.
259
MIDI Tracks
The MIDI Track Mixer shows levels, panning, and mute states for all used tracks.
To view a specific setting on all tracks, tap Level, Pan, or Mute at the bottom of the screen. Tap Mute/Solo to
switch between them.
When a track is selected, you can view and adjust all of its settings in the left side of the screen rather than using the
tab buttons at the bottom.
When viewing the MIDI track channel strip:
Note: This is the same as the MIDI track channel strip in Main Mode.
The first field shows the current track (which you can change).
The second field shows the current program the track is using (which you can change to a program of the same type).
Tap Solo or Mute to solo or mute the track (respectively).
Adjust the pan knob or velocity slider to change the panning or velocity of the track.
260
Audio Tracks
The Audio Track Mixer shows levels, mute/solo/record-arm states, send and insert effects, and routing for all used
tracks.
To view a specific setting on all tracks, tap Level, Pan, Mute/Solo/Rec Arm, Send, Insert, or Route at the
bottom of the screen. Tap Mute/Solo/Rec Arm to cycle through them.
When a track is selected, you can view and adjust all of its settings in the left side of the screen rather than using the
tab buttons at the bottom.
When viewing the audio track channel strip:
Note: This is the same as the audio track channel strip in Main Mode.
The first field defines the input source of the external audio signal, which you can set to a pair of inputs (Input
1,2–3,4 in Standalone Mode, Input 1,2–31,32 in Controller Mode) or a single input (Input 1–4 in Standalone
Mode, Input 1–32 in Controller Mode).
The second field shows where the track is routed, which you can change: Out 1,2–7,8, Out 1–8 or Sub 1–8 in
Standalone Mode; and Out 1,2–31,32 or Out 1–32 in Controller Mode.
Note: When set to a mono channel, the left and right channels are summed post-pan knob. If the pan knob is set
to the center position, the left and right channels will be summed and padded. If the pan knob is set to the
maximum left or right positions, only the respective channel will be sent to the output.
The Inserts field shows any enabled or disabled effects for that audio track. Tap the area under Inserts to open
a window where you can load, change, and enable or disable the effects for all four insert slots.
Tap Solo or Mute to solo or mute the track (respectively).
Tap the Monitor button to set how your audio track will be monitored. Tapping it will cycle through its three states:
When set to Auto, you will hear incoming audio while the track is record-enabled only.
When on, you will hear incoming audio whether or not the track is record-enabled.
When off, you will never hear any incoming audio.
261
Tap the automation button or press Read/Write (MPC X) to cycle through its three states:
When off, the audio track will ignore automation data. If you have already recorded or entered
automation, tapping this will switch between Read (R) and Write (W) only, but you can override
this and turn it off by pressing and holding Shift while pressing or tapping the button.
Important: If you have already recorded automation and turn it off, the audio track will still use
the effect and its parameter values at the point where you turned it off.
When set to Read (R), the audio track will read automation data but will not record any additional
automation over it. (Think of this as a protective feature to prevent accidental changes to your
automation while recording.)
When set to Write (W), the audio track can record automation. (If you have any Q-Link knobs
assigned to automatable parameters, make sure not to touch any accidentally while you are
recording.)
Tip: You can quickly set all programs and audio tracks to the same automation by tapping the
global automation button in the upper-right corner of the screen. See General Features >
Automation to learn about this.
Adjust the pan knob or level slider to change the panning or level of the track.
Tap the Record Arm button or press Rec Arm (MPC X) to record-enable the track. When you
begin audio recording, the audio signal will be recorded to this track.
Tip: You can select multiple tracks in the Rec Arm tab by pressing and holding Shift and tapping
each pad on the screen. You can also do this in the Track View by pressing and holding Shift
while tapping the Arm button to each track.
262
Programs
The Program Mixer shows levels, panning, mute states, send and insert effects, and routing for all programs.
To view a specific setting on all programs, tap Level, Pan, Mute/Solo, Send, Insert, or Route at the bottom of the
screen. Tap Mute/Solo to switch between them. Tap Send or Insert to cycle through the four available slots for each.
When a program is selected, you can view and adjust all of its settings in the left side of the screen rather than using
the tab buttons at the bottom.
When viewing the program channel strip:
Note: This is the same as the program channel strip in Main Mode.
The first field shows the current program number and name (which you can change).
The second field shows where the program is routed, which you can change: Out 1,2–7,8 or Out 1–8 in Standalone
Mode, Out 1,2–31,32 or Out 1–32 in Controller Mode. You can also select a submix (Sub 1–8) in Controller Mode.
Note: When set to a mono channel, the left and right channels are summed post-pan knob. If the pan knob is set
to the center position, the left and right channels will be summed and padded. If the pan knob is set to the
maximum left or right positions, only the respective channel will be sent to the output.
The Inserts field shows any enabled or disabled effects for that program. Tap the area under Inserts to open a
window where you can load, change, and enable or disable the effects for all four insert slots.
Tap Solo or Mute to solo or mute the program (respectively).
263
Tap the program automation button to change the program’s automation. Tapping it will cycle through its three
states:
When off, the program will ignore automation data. If you have already recorded or entered
automation, tapping this will switch between Read (R) and Write (W) only, but you can
override this and turn it off by pressing and holding Shift while tapping the button.
Important: If you have already recorded automation and turn it off, the track will still use the
effect and its parameter values at the point where you turned it off.
When set to Read (R), the program will read automation data but will not record any additional
automation over it. (Think of this as a protective feature to prevent accidental changes to your
automation while recording.)
When set to Write (W), the program can record automation. (If you have any Q-Link knobs
assigned to automatable parameters, make sure not to touch any accidentally while you are
recording.)
Tip: You can quickly set all programs and audio tracks to the same automation by tapping the
global automation button in the upper-right corner of the screen. See General Features >
Automation to learn about this.
Adjust the pan knob or level slider to change the panning or level of the program.
264
Returns
Pads, programs, and audio tracks can each be sent to up to four send channels. Their audio signals will be routed to
the send channels at their designated send levels. After being processed by the effects on those channels, their
signals are then sent to the assigned master output based on their return settings (levels, panning, etc.). This view
displays the four return channels. The return mixer shows levels, panning, mute states, insert effects, and routing for
all used tracks.
To view a specific setting on all returns, tap Level, Pan, Mute, Insert, or Route at the bottom of the screen. You
can tap Insert multiple times to cycle through the four available slots.
When a return is selected, you can view and adjust all of its settings in the left side of the screen rather than using
the tab buttons at the bottom.
When viewing the return channel strip:
The first field shows the current return number (which you can change).
The second field shows where the return is routed, which you can change: Out 1,2–7,8 or Out 1–8 in Standalone
Mode; Out 1,2–31,32 or Out 1–32 in Controller Mode (MPC Live does not use Out 7,8 in Standalone Mode but
displays them to maintain compatibility with MPC X, which does use them).
Note: When set to a mono channel, the left and right channels are summed post-pan knob. If the pan knob is set
to the center position, the left and right channels will be summed and padded. If the pan knob is set to the
maximum left or right positions, only the respective channel will be sent to the output.
The Inserts field shows any enabled or disabled effects for that return. Tap the area under Inserts to open a
window where you can load, change, and enable or disable the effects for all four insert slots.
Tap Mute to mute the return.
Adjust the pan knob or level slider to change the panning or level of the return.
265
Submixes
The Submixer shows levels, panning, mute states, send and insert effects, and routing for the eight available submixes.
To view a specific setting on all submixes, tap Level, Pan, Mute, Send, Insert, or Route at the bottom of the
screen. You can tap Send or Insert multiple times to cycle through the four available slots for each.
When a submix is selected, you can view and adjust all of its settings in the left side of the screen rather than using
the tab buttons at the bottom.
When viewing the submixer channel strip:
The first field shows the current submix (which you can change).
The second field shows where the submix is routed, which you can change: Out 1,2–31,32 or Out 1–32.
Note: When set to a mono channel, the left and right channels are summed post-pan knob. If the pan knob is set
to the center position, the left and right channels will be summed and padded. If the pan knob is set to the
maximum left or right positions, only the respective channel will be sent to the output.
The Inserts field shows any enabled or disabled effects for that submix. Tap the area under Inserts to open a
window where you can load, change, and enable or disable the effects for all four insert slots.
Tap Mute to mute the submix.
Adjust the pan knob or level slider to change the panning or level of the submix.
266
Masters
The Master Mixer shows levels, panning, mute states, and insert effects for all used stereo pairs of outputs (Out 1,2–
7,8 in Standalone Mode, Out 1,2–31,32 in Controller Mode; MPC Live does not use Out 7,8 in Standalone Mode but
displays them to maintain compatibility with MPC X, which does use them).
To view a specific setting on all outputs, tap Level, Pan, Mute, or Insert at the bottom of the screen. You can tap
Insert multiple times to cycle through the four available slots.
When viewing the master channel strip:
Note: This is the same as the master channel strip in Main Mode.
The first field shows the current master output (which you can change).
The Inserts field shows any enabled or disabled effects for that master output. Tap the area under Inserts to
open a window where you can load, change, and enable or disable the effects for all four insert slots.
Tap Mute to mute that master output.
Adjust the pan knob or level slider to change the panning or level of the master output.
267
Pad Mute Mode
Pad Mute Mode lets you easily mute pads within a program or set mute groups for each pad
within a program.
To enter Pad Mute Mode, do either of the following:
•
Press Menu, and then tap Pad Mute.
•
Press Shift+Track Mute/Pad Mute (MPC X).
There are two tabs you can view in this mode: Pad Mute or Pad Group. Tap each button in the lower-left corner to
select it. See the following Pad Mute and Pad Group sections to learn about each.
Use the Program field at the top of the screen to select a program.
The time counter in the upper-right corner the current playhead position. This is shown in most of the modes. See
General Features > Time Counter/Locate to learn about this.
The automation button indicates the global automation state. This is shown in several modes. See General Features
> Automation to learn about this.
Time Correct lets you quantize pad mutes. This is useful when you want your mutes to line up with a specific time
division. For example, with Time Division set to 1 Bar, your mutes will always align with the beginning of the measure
immediately after you press the pad.
Tap Time Division at the bottom of the screen, and select a value from 1/16 to 2 Bars (T indicates a tripletbased time division).
Tap TC at the bottom of the screen to enable or disable the Time Correct feature.
268
Pad Mute
You can mute or unmute individual sounds (on a single track) in real time by pressing the pads. This is useful if you
want to hear a track without a particular sound or if you want to isolate specific sounds or combinations of sounds.
Tip: This function is similar to muting pads one at a time in the grid—but more convenient.
To mute pads in this mode:
1. If the Pad Mute tab in the lower-left corner is not already selected, tap it.
2. Select the desired pad bank. Use the Pad Bank Buttons or tap a pad bank shown on the left side of the screen.
3. To mute or unmute a pad’s sound, press it or tap it on the screen. Muted pads are lit red. Unmuted pads are lit
yellow. Unused pads do not show any sample names.
To assign pads to pad groups within this tab, turn each of the Q-Link knobs (when the Screen Control Q-Link
button is selected) to assign each of the pads to a pad group. The number of each pad’s group is shown in its upperright corner.
269
Pad Group
The pad group feature extends the concept of pad mutes: you can mute or unmute multiple pads (on a single track)
by pressing one pad that you have assigned to a mute group. This is useful if you want to hear a track without a
particular group of sounds or if you want to isolate specific sounds in various combinations. You can create up to 16
different pad groups.
To use pad groups:
1. If the Pad Group tab in the lower-left corner is not already selected, tap it.
2. Use the Pad Bank buttons to select the desired pad bank.
3. To select a pad to add to a mute group, press it or tap it on the screen. The selected pad is lit green. If there
are other pads in the same mute group, they will flash yellow.
4. To add the pad to the mute group, tap the number of the desired mute group on the left side of the screen. To
remove it from the mute group, tap Off.
Alternatively, turn each of the Q-Link knobs (when the Screen Control Q-Link button is selected) to assign each of
the pads to a pad group. The number of each pad’s group is shown in its upper-right corner.
270
Track Mute Mode
Track Mute Mode lets you easily mute tracks within a sequence or set track groups, enabling
you to mute multiple tracks at once.
To enter Track Mute Mode, do either of the following:
•
Press Menu, and then tap Track Mute.
•
Press Track Mute (MPC X).
There are two tabs you can view in this mode: Track Mute or Track Group. Tap each button in the lower-left corner
to select it. See the following Track Mute and Track Group sections to learn about each.
Use the Sequence field at the top of the screen to select a sequence.
The time counter in the upper-right corner the current playhead position. This is shown in most of the modes. See
General Features > Time Counter/Locate to learn about this.
Time Correct lets you quantize track mutes. This is useful when you want your mutes to line up with a specific time
division. For example, with Time Division set to 1 Bar, your mutes will always align with the beginning of the
measure immediately after you press the pad.
Tap Time Division at the bottom of the screen, and select a value from 1/16 to 2 Bars (T indicates a tripletbased time division).
Tap TC at the bottom of the screen to enable or disable the Time Correct feature.
Tap Solo to turn track soloing on or off. When on, using Track Mute Mode will solo tracks instead of muting them.
271
Track Mute
This is useful if you want to hear a sequence without a particular track (e.g., muting your keyboard track to focus on
the bass) or if you want to isolate specific sounds or combinations of sounds that are separated by track.
Tip: This function is similar to, but more convenient than, muting tracks one at a time in the Track View.
To mute tracks in this mode:
1. If the Track Mute tab in the lower-left corner is not already selected, tap it.
2. Select the desired pad bank. Use the Pad Bank buttons or tap a pad bank shown on the left side of the screen.
3. To mute or unmute a track, press the corresponding pad or tap it on the screen. Pads for muted tracks are lit
red. Pads for unmuted tracks are lit yellow. Pads for unused tracks do not show any information.
To assign tracks to track groups within this tab, turn each of the Q-Link knobs (when the Screen Control Q-Link
button is selected) to assign each of the pads to a track group. The number of each pad’s track group is shown in its
upper-right corner.
272
Track Group
The track group feature extends the concept of track mutes: you can mute or unmute multiple tracks (in a single
sequence) by pressing one pad that you have assigned to a track group. This is useful if you want to hear a track
without a particular group of sounds or if you want to isolate specific sounds in various combinations. You can create
up to 16 different track groups.
To assign tracks to track groups:
1. If the Track Group tab in the lower-left corner is not already selected, tap it.
2. Select the desired pad bank by using the Pad Bank buttons.
3. To select a track to add to a mute group, press the corresponding pad or tap it on the screen. The pad for the
selected track is lit green. If there are other pads for tracks in the same mute group, they will flash yellow.
4. To add the track to a mute group, tap the number of the desired mute group.
To remove the track from the mute group, tap Off.
Alternatively, turn each of the Q-Link knobs (when the Screen Control Q-Link button is selected) to assign each of
the pads to a track group. The number of each pad’s track group is shown in its upper-right corner.
273
Next Sequence Mode
Next Sequence Mode lets you trigger different sequences simply by playing the pads. This is
useful for live performances, letting you change a song’s structure in real time.
To enter Next Sequence Mode, do either of the following:
•
Press Menu, and then tap Next Sequence.
•
Press Next Seq (MPC X).
The time counter in the upper-right corner the current playhead position. This is shown in most of the modes. See
General Features > Time Counter/Locate to learn about this.
The sequence playlist on the left side shows a list-style overview of all used
sequences in your project:
The Sequence column shows the name of the song’s sequences.
The Length column shows the bar length of a sequence.
The BPM column shows the tempo of a sequence in beats per minute.
The currently selected sequence is highlighted in the list. Tap a sequence in the list
to select it.
274
In Next Sequence Mode, every pad is assigned to a
sequence, starting from Pad A01 with Sequence 1 and
ascending from there. The pads will show the names of their
corresponding sequences. Empty pads correspond to unused
sequences. The currently selected pad will flash green.
During playback, change the next sequence that will play by
pressing the corresponding pad or tapping it on the screen.
If you do not select another sequence, the current sequence
will repeat indefinitely.
As a sequence plays, you can use the buttons at the bottom of the screen to change how playback works:
To switch to the currently selected sequence at the beginning of the next bar, tap Next Bar. This is useful if
you want to switch to another sequence before the current one ends without having to worry about timing issues.
To switch to the currently selected sequence immediately, tap Sudden. The new sequence will start playing
whether or not the current sequence is done. This is useful in live performances if you need to switch to the next
sequence instantly at a certain cue.
To delete the currently selected sequence from the sequence playlist, tap Clear. This option is available only
if that sequence is not playing at that moment.
To repeat the current sequence indefinitely and temporarily ignore pad presses, tap Hold. To return to
normal operation, tap it again. This is useful if you want to select other pads without selecting them to play next.
To copy the sequence playlist to a song, tap  Song while playback is stopped.
In the Copy to Song screen that appears, select a song, and then tap Do It to continue or Close to cancel.
To read more about Song Mode, please see the Song Mode chapter.
275
Song Mode
Song Mode lets you arrange sequences in a specific order and/or repetition to create songs.
You can edit the structure of a song during playback for easy, on-the-fly composing.
A project can contain up to 32 songs, each consisting of up to 999 “steps.” Each step can have
an assigned sequence as well as the number of times that sequence will repeat.
To open Song Mode, do either of the following:
•
Press Menu, and then tap Song Mode.
•
Press Shift+Next Seq/Song (MPC X).
Important: If a sequence is currently playing, stop playback before entering Song Mode. You cannot enter Song
Mode during playback.
Important: When creating a song, the program used by each track in the song’s first sequence will be used by all
subsequent tracks. In other words, all identically numbered tracks (across sequences) will use the program used by
the first sequence in the song—regardless of what programs each track uses while not in Song Mode.
For example, if you create a project in this way…:
• Track 1 of Sequence 1 uses a drum program.
• Track 1 of Sequence 2 uses a keygroup program.
• A song uses Sequence 1 as its first sequence and then uses Sequence 2 any time after it.
…then, in that song, Track 1 in Sequence 2 will use the same drum program as Track 1, Sequence 1.
Because of this, we recommend trying to be consistent while creating tracks in sequences that you intend to use in a
single song. Remember that you can copy one track to another if you ever need to reorder the tracks of a sequence
(see Modes > Main Mode > Track Section to learn about this).
Use the Song field to select the song you want to show.
Use the BPM field to adjust the tempo of the sequence.
To set whether the sequence follows its own tempo (Seq) or a master tempo (Mst), tap the
Seq/Mst button next to the BPM field. Alternatively, press Shift+Tap/Master.
276
The sequence playlist on the left lists of the “steps” of a song.
Each step has (in columns, left to right):
•
the step number (each song can contain up to 999 steps)
•
a sequence number and name
•
how many times the sequence plays (each step can play
up to 999 times; set it to Hold [the lowest/minimum
value] to set the sequence to repeat indefinitely until you
stop playback)
•
the tempo of the sequence
•
the number of bars the step occupies (based on how
many times it plays)
Each used sequence is assigned to a pad. Empty pads
correspond to unused sequences. Use the Pad Bank buttons
to access the sequences assigned to pads in other banks.
To insert a step:
1. Tap a step in the sequence playlist after which you want to insert a step.
2. Tap Insert in the lower-right corner of the screen.
Alternatively, “record” a song using the pads:
Note: The sequences or song will not play back as you use the pads to create your song in this way. Pressing the
pads just enters their corresponding sequences as steps.
1. Press Rec or Overdub to “record-arm” the song.
2. Press or tap the pad that corresponds to the first sequence you want to use. That sequence will appear in the
sequence playlist as the first step.
3. Repeat Step 2 for each additional step you want to add to the sequence playlist. Press or tap a pad multiple
times to add to the number of times it plays.
4. Press Stop to stop “recording.”
277
To change a step’s sequence:
1. In the desired step, tap the sequence name.
2. Use the data dial or –/+ buttons to select another sequence.
To delete a step, tap it, and then tap Delete in the lower-right corner of the screen.
To clear the entire sequence playlist (delete all steps), tap Clear.
To switch to the next sequence at the beginning of the next bar during playback, tap Next. This is useful if you
want to switch to another sequence before the current one ends without having to worry about timing issues.
To switch to the next sequence immediately during playback, tap Sudden. The new sequence will start playing
whether or not the current sequence is done. This is useful in live performances if you need to switch to the next
sequence instantly at a certain cue.
To convert the current song to a single sequence:
1. Tap Convert > Seq to open the Convert to Sequence
window.
2. Use the To Sequence field to select which sequence
you want the song to export to.
3. Use the Track Status field to select whether you want
the song to Ignore Muted Tracks or Include Muted
Tracks in the new sequence.
4. To confirm your selections, tap Do It.
To cancel the process, tap Close.
To render/export your song as an audio file, tap Export
to open the Audio Mixdown screen. See General Features
> Audio Mixdown to learn how to use this screen to export
your song.
278
Q-Link Edit Mode
Q-Link Edit Mode lets you determine what the Q-Link knobs control in other modes. This is
helpful when you want to use the Q-Link knobs to control parameters that might not be
shown in the current mode—or parameters that are shown across different modes.
To enter Q-Link Edit Mode, do any of the following:
•
Press Menu, and then tap Q-Link Edit.
•
Press Shift+Screen Control/Edit (MPC X).
•
Press and hold one of the five Q-Link buttons above the Q-Link knobs, and then tap Q-Link Edit at the
bottom of the window that appears (MPC X).
To select an edit mode for the Q-Link knobs, tap one of the five buttons at the bottom of the screen. If you are
using MPC X, you can also press one of the five Q-Link buttons above the Q-Link knobs (Project, Program, Pad
Scene, Pad Param, or Screen Control/Edit):
Project: In this edit mode, the Q-Link knobs can control 16 parameters within the current project overall. See the
following Project section to learn about this specific Q-Link Edit Mode.
Program/Audio Track: In this edit mode, the Q-Link knobs can control 16 program or audio track parameters.
See the following Program/Audio Track section to learn about this specific Q-Link Edit Mode.
Pad Scene (for drum programs only): In this edit mode, the Q-Link knobs can control 16 parameters for the
currently selected pad. See the following Pad Scene section to learn about this specific Q-Link Edit Mode.
Pad Parameter: In this edit mode, the 16 Q-Link knobs correspond to the 16 pads, each one controlling the
same parameter for each pad. This is useful if you need to adjust the same parameter on multiple pads at once
rather than having to select and edit each pad individually. See the following Pad Parameter section to learn
about this specific Q-Link Edit Mode.
Screen: In this edit mode, the Q-Link knobs will control a parameter or group of parameters in your currently
selected mode (e.g., Main Mode, Sample Edit Mode, etc.).
Use the Track field to select a track that uses the desired program (and therefore pad/pads). The contents of the
screen below will vary based on (1) the type of program each track uses and (2) the Q-Link Edit Mode you selected.
279
Tap the Learn button to turn Learn Mode on or off. When on, adjusting a control in the MPC software window will
immediately assign it to the currently selected Q-Link knob.
This button is not available while in Screen Q-Link Edit Mode where the Q-Link knobs are unassignable.
To assign a function to a Q-Link knob in Learn Mode:
1. Tap Learn so the button is lit. (This will stop playback. Resuming playback will exit Learn Mode.)
2. Touch or turn the desired Q-Link knob.
3. In the MPC software on your computer, click and drag the slider or knob you want to assign to the Q-Link knob.
The Q-Link knob will be able to control that parameter immediately.
To assign functions to other Q-Link knobs, repeat Steps 2–3.
To exit Learn Mode, tap Learn (or resume playback).
The automation button indicates the global automation state. This is shown in several modes. See General Features
> Automation to learn about this.
At any time, in any mode, you can show the QLinks window over the touchscreen’s current contents. These are the
same parameters and settings as what is shown in Q-Link Edit Mode.
To show the QLinks window, press and hold any of the Q-Link buttons: Project, Program, Pad Scene, Pad
Param, or Screen Control/Edit (MPC X) or the Q-Link button (MPC Live, MPC Touch).
To close the QLinks window, release that Q-Link button.
While the QLinks window is shown:
To adjust the settings of the selected knobs, turn the corresponding Q-Link knobs on your MPC hardware.
To select an edit mode for the Q-Link knobs, tap one of the five buttons at the bottom of the screen. If you are
using MPC X, you can also press one of the five Q-Link buttons above the Q-Link knobs: Project, Program, Pad
Scene, Pad Parameter, or Screen.
To turn Learn Mode on or off, tap Learn. (This button is not available while in Screen Q-Link Edit Mode where
the Q-Link knobs are unassignable.)
To enter Q-Link Edit Mode immediately (regardless of the current mode), tap Q-Link Edit at the bottom of the
window.
280
Project
In the Project Q-Link Edit Mode, the Q-Link knobs control 16 parameters within the current project.
Next to the top row of Q-Link knobs on the screen, tap one of these tabs to select the type of parameters you want
to control with the Q-Link knobs:
MIDI Track: MIDI track parameters. Use the MIDI Track field to select one of the MIDI tracks in your project.
Audio Track: audio track parameters. Use the Audio Track field to select one of the audio tracks in your project.
Program: program parameters. Use the Program field to select one of the programs in your project.
Return: return parameters. Use the Return field to select one of Returns 1–4.
Submix: submix parameters. Use the Submix field to select one of Submixes 1–8.
Master: master parameters. Use the Master field to select one of the output pairs: Outputs 1/2–7/8 in Standalone
Mode or Outputs 1/2–31/32 in Controller Mode (MPC Live does not use Out 7/8 in Standalone Mode but displays
them to maintain compatibility with MPC X, which does use them).
Next to the second row of Q-Link knobs on the screen, tap one of these tabs to select the type of parameters you
want to control with the Q-Link knobs:
Mixer: general mixer parameters
Program (in the Program tab if a drum program or clip program is selected): program parameters
Insert 1–4 (not available in the MIDI Track tab or Program tab if a MIDI program is selected): parameters for its
program insert effects
If the Program tab is selected, use the Type selector to determine whether the Q-Link knobs will control the parameters
of the entire program (Program) or for a single pad (Pad).
To select a program, use the Program field next to the top row of Q-Link knobs on the screen.
To select a pad (if Type is set to Pad), use the Pad field.
281
Use the Parameter field to select the parameter you want to control with the currently selected Q-Link knob.
When the MIDI Track tab is selected:
Mixer: Off, Volume, Pan, Mute, Solo
When the Audio Track tab is selected:
Mixer: Off, Volume, Pan, Mute, Solo, Send 1–4
Insert 1–4: Off, other available parameters depend on the effect
When the Program tab is selected and Type is set to Program:
Mixer: Off, Volume, Pan, Mute, Solo, Send 1–4
Program: Off, Master Semi Tune, Master Fine Tune
Insert 1–4: Off, other available parameters depend on the effect
When the Program tab is selected and Type is set to Pad:
Mixer: Off, Level, Pan, Pad Mute, Pad Solo, Send 1–4
Program:
Off
Amp Env Hold
Layer Sample Pan (1–4)
LFO to Filter
Velocity to Amp
Tuning
Amp Env Sustain
Layer Semi Tune (1–4)
LFO to Amp
Velocity to Pan
Filter Cutoff
Filter Env Attack
Layer Fine Tune (1–4)
LFO to Pan
Layer Direction (1–4)
Filter Resonance
Filter Env Hold
Velocity to Start
LFO Wave
Layer Offset (1–4)
Filter Env Amount
Filter Env Decay
Vel to Filter Attack
LFO Rate
Amp Env Attack
Filter Env Sustain
Velocity to Env Amount
LFO Sync
Amp Env Decay
Filter Env Release
Velocity to Filter
Velocity to Pitch
Amp Env Release
Layer Level (1–4)
LFO to Pitch
Vel to Volume Attack
Insert 1–4: Off, other available parameters depend on the effect
When the Return tab is selected:
Mixer: Off, Volume, Pan, Mute
Insert 1–4: Off, other available parameters depend on the effect
When the Submix tab is selected:
Mixer: Off, Volume, Pan, Mute, Send 1–4
Insert 1–4: Off, other available parameters depend on the effect
When the Master tab is selected:
Mixer: Off, Volume, Pan, Mute
Insert 1–4: Off, other available parameters depend on the effect
Tap the Momentary checkbox to turn momentary behavior on or off.
When on, moving the Q-Link knob will adjust its parameter, but the parameter will immediately return to its
original position (when you turned Momentary on) when you release the Q-Link knob.
When off, moving the Q-Link knob will adjust its parameter, and the parameter will remain at its new setting
when you release the Q-Link knob.
282
Program/Audio Track
In the Program/Audio Track Q-Link Edit Mode, the Q-Link knobs control 16 parameters within the currently selected
program or audio track.
When a MIDI track is selected:
Next to the top row of Q-Link knobs on the screen, tap one of these tabs to select the type of parameters you want
to control with the Q-Link knobs:
Mixer: general mixer parameters
Program: program parameters
Insert 1–4: parameters for its program insert effects
Use the Type selector to determine whether the Q-Link knobs will control the parameters of the entire program
(Program) or for a single pad (Pad).
To select a program, use the Track field at the top of the screen to select a track that uses it. The program
name will appear in the Program field next to the top row of Q-Link knobs on the screen.
To select a pad (if Type is set to Pad), use the Pad field.
Use the Parameter field to select the parameter you want to control with the Q-Link knobs.
When Type is set to Program:
Mixer: Off, Volume, Pan, Mute, Solo, Send 1–4
Program: Off, Master Semi Tune, Master Fine Tune
Insert 1–4: Off, other available parameters depend on the effect
283
When Type is set to Pad:
Mixer: Off, Level, Pan, Pad Mute, Pad Solo, Send 1–4
Program:
Off
Amp Env Hold
Layer Sample Pan (1–4)
LFO to Filter
Velocity to Amp
Tuning
Amp Env Sustain
Layer Semi Tune (1–4)
LFO to Amp
Velocity to Pan
Filter Cutoff
Filter Env Attack
Layer Fine Tune (1–4)
LFO to Pan
Layer Direction (1–4)
Filter Resonance
Filter Env Hold
Velocity to Start
LFO Wave
Layer Offset (1–4)
Filter Env Amount
Filter Env Decay
Vel to Filter Attack
LFO Rate
Amp Env Attack
Filter Env Sustain
Velocity to Env Amount
LFO Sync
Amp Env Decay
Filter Env Release
Velocity to Filter
Velocity to Pitch
Amp Env Release
Layer Level (1–4)
LFO to Pitch
Vel to Volume Attack
Insert 1–4: Off, other available parameters depend on the effect
Tap the Momentary checkbox to turn momentary behavior on or off.
When on, moving the Q-Link knob will adjust its parameter, but the parameter will immediately return to its
original position (when you turned Momentary on) when you release the Q-Link knob.
When off, moving the Q-Link knob will adjust its parameter, and the parameter will remain at its new setting
when you release the Q-Link knob.
When an audio track is selected:
Next to the top row of Q-Link knobs on the screen, tap one of these tabs to select the type of parameters you want
to control with the Q-Link knobs:
Mixer: general mixer parameters
Insert 1–4: parameters for its program insert effects
Use the Parameter field to select the parameter you want to control with the Q-Link knobs.
Tap the Momentary checkbox to turn momentary behavior on or off.
When on, moving the Q-Link knob will adjust its parameter, but the parameter will immediately return to its
original position (when you turned Momentary on) when you release the Q-Link knob.
When off, moving the Q-Link knob will adjust its parameter, and the parameter will remain at its new setting
when you release the Q-Link knob.
284
Pad Scene
In the Pad Scene Q-Link Edit Mode, the Q-Link knobs control your favorite 16 parameters for the currently selected
pad. You can select another pad simply by pressing it, allowing you to adjust the same 16 parameters for that new pad.
(These assignments are automatically saved with other user settings. Any project you load will use these assignments.)
To select a pad, press it.
Next to the top row of Q-Link knobs on the screen, tap one of these tabs to select the type of parameters you want
to control with the Q-Link knobs:
Mixer: general mixer parameters
Program: pad parameters (i.e., parameters used in Program Edit Mode)
Use the Parameter field to select the parameter you want to control with the Q-Link knobs.
Mixer: Off, Level, Pan, Pad Mute, Pad Solo, Send 1–4
Program:
Off
Amp Env Hold
Layer Sample Pan (1–4)
LFO to Filter
Velocity to Amp
Tuning
Amp Env Sustain
Layer Semi Tune (1–4)
LFO to Amp
Velocity to Pan
Filter Cutoff
Filter Env Attack
Layer Fine Tune (1–4)
LFO to Pan
Layer Direction (1–4)
Filter Resonance
Filter Env Hold
Velocity to Start
LFO Wave
Layer Offset (1–4)
Filter Env Amount
Filter Env Decay
Vel to Filter Attack
LFO Rate
Amp Env Attack
Filter Env Sustain
Velocity to Env Amount
LFO Sync
Amp Env Decay
Filter Env Release
Velocity to Filter
Velocity to Pitch
Amp Env Release
Layer Level (1–4)
LFO to Pitch
Vel to Volume Attack
Tap the Momentary checkbox to turn momentary behavior on or off.
When on, moving the Q-Link knob will adjust its parameter, but the parameter will immediately return to its
original position (when you turned Momentary on) when you release the Q-Link knob.
When off, moving the Q-Link knob will adjust its parameter, and the parameter will remain at its new setting
when you release the Q-Link knob.
285
Pad Parameter
In the Pad Parameter Q-Link Edit Mode, the Q-Link knobs control the same pad parameter for the each of the 16
pads in the current pad bank.
For example, if the Parameter is set to Level, the 16 Q-Link knobs will adjust the 16 independent Level settings for
each pad in the current pad bank. You could then set the Parameter to Pan and use the Q-Link knobs to adjust the
panning of all 16 pads.
Next to the top row of Q-Link knobs on the screen, tap one of these tabs to select the type of parameter you want to
control with the Q-Link knobs:
Mixer: general mixer parameters
Program: pad parameters (i.e., parameters used in Program Edit Mode)
Use the Parameter field to select the parameter you want to control with the Q-Link knobs.
Mixer: Off, Level, Pan, Pad Mute, Pad Solo, Send 1–4
Program:
Off
Amp Env Hold
Layer Sample Pan (1–4)
LFO to Filter
Velocity to Amp
Tuning
Amp Env Sustain
Layer Semi Tune (1–4)
LFO to Amp
Velocity to Pan
Filter Cutoff
Filter Env Attack
Layer Fine Tune (1–4)
LFO to Pan
Layer Direction (1–4)
Filter Resonance
Filter Env Hold
Velocity to Start
LFO Wave
Layer Offset (1–4)
Filter Env Amount
Filter Env Decay
Vel to Filter Attack
LFO Rate
Amp Env Attack
Filter Env Sustain
Velocity to Env Amount
LFO Sync
Amp Env Decay
Filter Env Release
Velocity to Filter
Velocity to Pitch
Amp Env Release
Layer Level (1–4)
LFO to Pitch
Vel to Volume Attack
Tap the Momentary checkbox to turn momentary behavior on or off.
When on, moving the Q-Link knob will adjust its parameter, but the parameter will immediately return to its
original position (when you turned Momentary on) when you release the Q-Link knob.
When off, moving the Q-Link knob will adjust its parameter, and the parameter will remain at its new setting
when you release the Q-Link knob.
286
Screen
In the Screen Q-Link Edit Mode, the Q-Link knobs will control only the parameter or group of parameters in your
currently selected mode (e.g., Main Mode, Sample Edit Mode, etc.).
287
Pad Color Mode
Pad Color Mode lets you assign specific colors to your pads in each program.
To enter Pad Color Mode, make sure you have first selected a track that uses the desired program, and then press
Menu, and tap Pad Color.
Important: If you are already in Pad Color Mode and want to assign pad colors for another program, exit Pad Color
Mode first, and then select a track that uses the desired program in another mode.
Use the field in the upper-left corner to set how the pad lights will display:
Off: The pads will be unlit whether you are playing them or not.
Classic Velocity: The pads will be unlit while you are not playing them. When you press them, they will light with
colors according to the velocity: red indicates a high velocity, yellow indicates a low velocity.
Fixed: The pads will be lit with their assigned colors whether you are playing them or not.
Off->Velocity: The pads will be unlit when you are not playing them. When you press them, they will light with
their assigned color with a brightness that corresponds with the velocity.
Dim->Velocity: The pads will be dimly lit when you are not playing them. When you press them, they will light
with their assigned color with a brightness that corresponds with the velocity.
Bright->Velocity: The pads will be brightly lit when you are not playing them. When you press them, they will
light with their assigned color with a brightness that corresponds with the velocity.
Use the Empty Pads field in the upper-left corner to set how empty pads will display:
Empty pads off: Pads without any sounds will remain off.
Empty pads dim: Pads without any sounds will remain more dimly lit than pads with sounds assigned.
Empty pads normal: Pads without any sounds will appear the same as pads with sounds assigned.
288
Use the Single Pad/All Pads select to determine whether you are setting the color for a Single Pad or All Pads.
Tip: To quickly assign that color to all pads in the program, press and hold Shift while tapping a color button.
Use the color buttons to select which color you are assigning.
Tip: To select the color button corresponding a specific pad’s color, press and hold Shift, and then press the
pad or tap it on the screen.
Press a pad on your MPC hardware or tap it on the screen to assign the selected color to it.
To make the current pad color settings the defaults for all programs on the same type (e.g., drum programs,
keygroup programs, etc.), tap Make Default. In the window that appears, tap Do It to confirm your choice or Cancel
to cancel.
289
MIDI Control Mode
You can use MIDI Control Mode on your MPC hardware to customize what MIDI messages
are sent from certain controls on your hardware. This custom “control map” will then work
whenever you are in MIDI Control Mode. The edits you make in MIDI Control Mode will be
retained with the current MPC project.
In Standalone Mode, this feature enables you to use your MPC X or MPC Live to control external MIDI devices
connected to its MIDI out.
In Controller Mode, this is helpful when using MPC as a plugin: you can use MIDI Control Mode to use your MPC
hardware to control your host software, and then switch back to any other mode to control the MPC plugin.
To enter MIDI Control Mode, press Menu, and then tap MIDI Control.
Important:
In Standalone Mode: Make sure your MPC hardware is using the correct MIDI output. You can set this in the
Preferences (see General Features > Menu > Preferences > Hardware).
In Controller Mode: In your host software, make sure your MPC hardware is selected as a MIDI controller device.
In the touchscreen, use the fields and selectors to set each control’s parameters to your preference. The available
parameters depend on its type: a pad, or button, a Q-Link knob, or each axis of the XY pad. When you have set all
of the parameters as desired, you can select another control or enter another mode.
To select a control to edit, do any of the following:
•
Press or turn it. In the lower-left corner, tap the Hardware tab to edit a pad, button, or Q-Link knob, or tap
the XY tab to edit the XY pad.
•
Tap the Control field in the upper-left corner, and then turn the data dial to select one.
•
Double-tap the Control field, and then tap a control name in the menu that appears.
Note: The Control field menu will show many more hardware controls than are actually available on your MPC
hardware. This is because the list includes all possible controls from all current MPC models (MPC X, MPC Live,
MPC Touch, etc.). You can edit only the controls that are described in this chapter.
Note: The software window will also display a graphical interface resembling your MPC hardware. Editable controls
show their current MIDI message. Pads and Q-Link knobs show their current MIDI channels.
290
Pads
These are the MIDI parameters you can edit for each pad:
Control: This is the hardware control you are currently editing (Pad 1–Pad 16).
Bank: This is the pad bank the pad belongs to. If you check the Set All box, the pad’s messages and
parameters will be identical across all eight banks.
Set All: When this box is checked, the pad’s messages and parameters will be identical across all eight banks.
When this box is unchecked, the pad’s messages and parameters will apply to the current pad only.
Light LED: This determines how the pad’s LEDs will behave.
When set to Never, the LEDs will always be off.
When set to MIDI Input, the LEDs will light up when the software receives a MIDI message that matches the pad.
When set to Local, the LEDs will light up when you press the pad and/or MIDI input is received.
MIDI Channel: This determines which MIDI channel (1–16) the pad will use to send its message to the software.
Note: This is the MIDI note number the pad will send to the software when you press it (0–127 or C-2 to G8).
Velocity: This determines whether the pad will be velocity-sensitive (On) or not (Off). When set to Off, pressing
the pad will send a note at full-level (127) always.
Aftertouch: This determines how the pad’s aftertouch (pressure applied to the pad after the initial press) behaves.
Off: The pad will not send any aftertouch messages.
Channel: If you press multiple pads that have this setting, the aftertouch messages they send will be identical.
Poly: If you press multiple pads, the aftertouch message each pad sends will be independent from the others.
291
Buttons
These are the MIDI parameters you can edit for each button. You can edit the Erase, Tap, Undo/Redo, or
Copy/Delete buttons:
Control: This is the hardware control you are currently editing (Erase, Tap, Undo, or Copy).
Light LED: This determines how the button’s LED (or multiple LEDs) will behave.
When set to Never, the LEDs will always be off.
When set to MIDI Input, the LEDs will light up when the software receives a MIDI message that matches the
button.
When set to Local, the LEDs will light up when you press the button and/or MIDI input is received.
MIDI Channel: This determines which MIDI channel (1–16) the button will use to send its message to the software.
CC Number: This determines what MIDI Control Change number the button will send to the software.
Type: This determines whether the button will behave as a Momentary switch or Toggle (latching) switch.
292
Q-Link Knobs
These are the MIDI parameters you can edit for each Q-Link knob:
Control: This is the hardware control you are currently editing (QLink 1–4).
Light LED: Although you can edit this parameter, it does not actually have a function on your MPC hardware.
When set to Never, the LEDs will always be off.
When set to MIDI Input, the LEDs will light up when the software receives a MIDI message that matches the
Q-Link knob.
When set to Local, the LEDs will light up when you touch or turn the Q-Link knob and/or MIDI input is received.
MIDI Channel: This determines which MIDI channel (1–16) the Q-Link knob will use to send its message to the
software.
CC Number: This determines what MIDI Control Change number the Q-Link knob will send to the software.
Mode: This determines how the Q-Link knob will control its parameter.
Absolute: The Q-Link knob’s current position determines its parameter’s value; moving it may cause its
parameter to “snap” to a new position if you’re using it to control different parameters in different modes.
Relative: Moving the Q-Link knob will increase or decrease its parameter regardless of its physical position.
Low Range: This is the Q-Link knob’s lowest possible value (0–127).
High Range: This is the Q-Link knob’s highest possible value (0–127).
Touch Sense: This activates or deactivates the Q-Link knob’s touch-capacitive circuitry.
On: You can touch the Q-Link knob to send a Note On message to the software (this is how your MPC
hardware normally works).
Off: The Q-Link knob will not send any Note On messages; it will only send CC messages when you turn it.
Note: This is the MIDI note number the Q-Link knob will send to the software when you touch it (0–127 or C-2 to
G8). Touch Sense must be set to On for this to work.
293
XY Pad
These are the MIDI parameters you can edit for each axis of the XY pad:
Control: This is the axis you are currently editing (XYFX X-Axis or XYFX Y-Axis). This field will be hidden if you
tapped the XY tab to show the XY pad’s parameters. You can tap the Hardware tab to show this field.
Mute: This button determines whether the axis is muted or not. When muted, its MIDI output is disabled. You
must be viewing the Settings to do this.
MIDI Channel: This determines which MIDI channel (1–16) the axis will use to send its message to the software.
CC Number: This determines what MIDI Control Change number the axis will send to the software.
Low Range: This is the axis’s lowest possible value (0–127).
High Range: This is the axis’s highest possible value (0–127).
MIDI Learn
You can use the MIDI Learn function to assign external MIDI controllers to various parameters in your specific MPC
project:
•
Mixer parameters such as volume, pan, mute, and solo for MIDI or audio tracks, programs, returns, submixes,
and master outputs
•
Pad parameters (for drum programs and clip programs only) such as tuning, filter and amp envelopes, layer
settings, LFO settings, and velocity
•
Program parameters, which depend on the program type
•
Insert effects parameters, which depend on the effect type
These assignments will be saved with your MPC project.
See Addenda > Updates in MPC 2.2 > New Features > MIDI Control Mode: MIDI Learn for more information.
294
Pad Perform Mode
Pad Perform Mode lets you assign musical scales/modes, chords, or progressions to the pads
for more creative performance.
To enter Pad Perform Mode, do either of the following while using a keygroup program, MIDI program, plugin
program, or CV program:
•
Press Menu, and then tap Pad Perform.
•
Press Pad Perform (MPC X).
Although you can enter Pad Perform Mode while using a drum program or clip program, it does not work with these
programs.
The touchscreen will show the current pad bank’s mapping of notes or chords.
295
Use the type selector in the top-left to determine what will be mapped over the pads:
Chromatic: Each pad is assigned a note, ascending by one semitone with each pad. Pads with notes in the key
determined by the Scale will be lit, while pads with notes between the scale degrees will be unlit.
Notes: Each pad is assigned a note, ascending by one scale degree with each pad.
Chords: Each pad is assigned a chord, the root note ascending by one scale degree with each pad. All available
chords will play in the key determined by the Scale.
Chromatic Chords: Each pad is assigned a chord, the root note ascending by one scale degree with each pad.
You can play any chord type regardless of the key determined by the Scale. Essentially, this is like the Chords
setting but with more options to play chords out of the set key.
Progressions: Each pad is assigned a chord in a chord progression. You can play the pads in (or out of) order to
construct songs quickly. The available chords are determined by the Chord field.
Tip: You can use your own progressions (created in the desktop version of the MPC software) on your MPC X or
MPC Live. See Addenda > Updates in MPC 2.1 > New Features > Pad Perform Mode: User Progressions to
learn more about this.
Chromatic Notes in Pad Perform Mode.
Notes in Pad Perform Mode.
Chords in Pad Perform Mode.
Chromatic Chords in Pad Perform Mode.
Progressions in Pad Perform Mode.
296
Use the Scale & Octave fields to determine the root note and the scale type.
Root Note (pitch and register): This is the starting point of the scale. The available notes are all chromatic notes
across the range of the pads. The pad that’s assigned the root note will be lit differently (and highlighted on the
screen) to indicate where the scale starts in each octave.
Scale Type: This is the scale or mode based on the root note (this is disabled when Type is set to Progressions).
The available scales are:
Major
Blues (minor)
Major Bebop
Lydian
Natural Minor
Flamenco
Whole Tone
Mixolydian
Harmonic Minor
Gypsy
Chromatic
Aeolian
Pentatonic Major
Hungarian Gypsy
Dorian
Locrian
Pentatonic Minor
Persian
Phrygian
Use the Chord fields to determine what chord type will play when pressing a pad. The chord will use those scale
degrees based off of the pad’s root note. You can use this only when the Type is set to Chords or Chromatic Chords.
When set to Chords, the available chords are:
1-3-5 (major/minor)
1-3-5-7 (major7/minor7)
1-4-5 (sus4)
1-3-5-7b (dominant)
1-2-5 (sus2)
When set to Chromatic Chords, the available chords are:
Major
Major7
Augmented
Minor
Minor7
Diminished
Sus2
Major9
Sus4
Minor9
Use the Banks field to determine how the notes are mapped across the pad banks.
Continuous: Pad 01 of one bank is always one scale degree higher than Pad 16 of the previous bank.
Start on Root: Pad 01 will always be the root note of the scale in every pad bank.
You can use the buttons at the bottom of the screen to quickly select different Types and Chords:
Tap Notes to automatically set the Type to Notes.
Tap 1-3-5 to automatically set the Type to Chords and set the Chord to 1-3-5 (major/minor).
Tap 1-3-5-7 to automatically set the Type to Chords and set the Chord to 1-3-5-7 (major7/minor7).
Tap Progressions to automatically set the Type to Progressions.
Tap Octave –/+ to shift the pad assignments down or up by an octave.
Press Shift+1-4-5 to automatically set the Type to Chords and set the Chord to 1-4-5 (sus4).
Press Shift+1-3-5-7b to automatically set the Type to Chords and set the Chord to 1-3-5-7b (dominant).
Press Shift+Note –/+ to shift the pad assignments down or up by a semitone, essentially raising or lowering the
Root Note field by a half-step.
297
Appendix
Effects & Parameters
This chapter lists the available effects. To learn more about how effects work with MPC, please see General Features
> Effects.
Note: Some of these effects have a “sync” version (e.g., Flanger Sync, Autopan Sync, etc.) whose rates will be
affected by the current tempo. While viewing the rate of these effects, a “.” next to the time division indicates a
triplet-based rate.
Reverbs
Options: Reverb Small, Reverb Medium, Reverb Large, Reverb Large 2, Reverb In Gate, Reverb Out Gate
Reverb Small
This is a spatial effect, designed to emulate a small room.
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
50
Pre-Delay
1–100
50
Early Reflection
0–100
50
Density
0–100
50
Diffuse
0–100
50
Decay
0–100
50
Lo-Cut
0–100
15
Hi-Cut
0–100
10
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
50
Pre-Delay
1–100
50
Early Reflection
0–100
50
Density
0–100
50
Diffuse
0–100
50
Decay
0–100
50
Lo-Cut
0–100
15
Hi-Cut
0–100
10
Reverb Medium
This is a spatial effect, designed to emulate a medium room.
298
Reverb Large
This is a spatial effect, designed to emulate the sound of a
large hall.
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
50
Pre-Delay
1–100
50
Early Reflection
0–100
50
Density
0–100
50
Diffuse
0–100
50
Decay
0–100
75
Lo-Cut
0–100
10
Hi-Cut
0–100
10
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
50
Pre-Delay
1–100
50
Early Reflection
0–100
50
Density
0–100
50
Diffuse
0–100
50
Decay
0–100
75
Lo-Cut
0–100
10
Hi-Cut
0–100
10
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
50
Pre-Delay
1–100
50
Early Reflection
0–100
50
Density
0–100
50
Diffuse
0–100
50
Decay
0–100
75
Lo-Cut
0–100
10
Hi-Cut
0–100
10
Gate In
0–100
0
Reverb Large 2
This is a less CPU-intensive spatial effect, emulating the
sound of a large hall.
Reverb In Gate
This is a hall reverb with an additional control. The reverb
effect is cut off when the input drops below the level set in
the Gate In parameter.
299
Reverb Out Gate
This is a hall reverb that has an additional control. The reverb Parameter
effect is cut off when the output drops below the level set in
Dry/Wet
the Gate Out parameter.
Pre-Delay
Value Range
Default Value
0–100 (dry–wet)
50
1–100
50
Early Reflection
0–100
50
Density
0–100
50
Diffuse
0–100
50
Decay
0–100
75
Lo-Cut
0–100
10
Hi-Cut
0–100
10
Gate Out
0–100
0
Delays
Delays the original signal for a specified period of time and plays it back over an adjustable period of time.
Options: Delay Mono, Delay Mono Sync, Delay Stereo, Delay Sync (Stereo), Delay LP, Delay HP, Delay Analog,
Delay Analog Sync, Delay Tape Sync, Delay Ping Pong, Delay Multi-Tap
Delay Mono
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
50
Time
2–2000 ms
100
Feedback
0–100
25
Damping
0–100
100
Delay Mono Sync
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
50
Time
1 bar – 1/16 triplets 1/4
Feedback
0–100
50
Damping
0–100
100
300
Delay Stereo
Stereo Delay operates similarly to Mono Delay but in true
stereo.
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
50
Time
2–2000 ms
100
Feedback
0–100
25
Damping
0–100
100
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
50
Time
1 bar – 1/16 triplets 1/4
Feedback
0–100
50
Damping
0–100
100
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
50
Time
2–2000 ms
500
Feedback
0–100
50
Cutoff
0–100
50
Resonance
0–100
20
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
50
Time
2–2000 ms
100
Feedback
0–100
50
Cutoff
0–100
33
Resonance
0–100
33
Delay Sync (Stereo)
Stereo Delay operates similarly to Mono Delay but in true
stereo.
Delay LP
LP Delay is identical to the Mono Delay, but it uses a
resonant low-pass filter in the delay line.
Delay HP
HP Delay is identical to the Mono Delay, but it uses a
resonant high-pass filter in the delay line.
301
Delay Analog
Analog Delay is similar to the Mono Delay, except that it’s
Parameter
designed to emulate an analog “Bucket Brigade”-style delay.
Dry/Wet
This delay has a unique character to it that gives a warmer
sound by adding subtle inaccuracies in phase and timing.
Time
Feedback
Value Range
Default Value
0–100 (dry–wet)
50
2–2000 ms
100
0–100
25
Value Range
Default Value
0–100 (dry–wet)
50
Delay Analog Sync
Analog Delay is similar to Mono Delay, except that it’s
Parameter
designed to emulate an analog “Bucket Brigade”-style delay.
Dry/Wet
This delay has a unique character to it that gives a warmer
sound by adding subtle inaccuracies in phase and timing.
Time
1 bar – 1/16 triplets 1/4
Feedback
0–100
50
Ramp
0–100
50
Value Range
Default Value
0–100 (dry–wet)
50
Delay Tape Sync
Tape Delay emulates a delay system using an analog tape
Parameter
loop and a series of tape heads to produce an echo effect.
This delay type yields a very distinct echo sound often heard Dry/Wet
in reggae and dub-style music.
Time
1 bar – 1/16 triplets 1/4
Feedback
0–100
50
Ramp
0–100
50
Head 1
0–100
100
Head 2
0–100
0
Head 3
0–100
0
Head 4
0–100
0
Tone
0–100
50
Spread
0–100
50
Wow & Flutter
0–100
50
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
50
Time, Left
2–2000 ms
100
Time, Right
2–2000 ms
100
Feedback
0–100
25
Damping
0–100
100
Delay Ping Pong
This stereo delay allows you to set different delay times for
its left and right repeats.
302
Delay Multi-Tap
This delay is a mono delay which has three delay generators
with independently adjustable delay times and stereo
position.
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
50
Time 1
2–2000 ms
100
Time 2
2–2000 ms
100
Time 3
2–2000 ms
100
Feedback
0–100
25
Pan 1
0–100
50
Pan 2
0–100
50
Pan 3
0–100
50
Damping
0–100
100
Gain 1
0–100
25
Gain 2
0–100
25
Gain 3
0–100
25
Flangers
A flanger is a modulated delay to emulate the sound created when running two analog tape machines in parallel with
a slight time misalignment. Slow Rate settings can produce a “whooshing” jet engine sound, while faster rates result
in more of a “warble.”
Options: Flanger, Flanger Sync
Flanger
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Rate
0–100
10
Feedback
-100 – 100
0
Delay
0–100
20
Width
0–100
80
Flanger Sync
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Rate
8 bars – 1/16 triplets
1/4
Feedback
-100 – 100
0
Delay
0–100
20
Width
0–100
80
303
Chorus
A chorus effect uses an LFO to modulate the pitch and a delay of the input signal, which are then added to the dry
signal. In small amounts, this creates the illusion of multiple voices playing at once. Turn up the Feedback and
Depth for more pronounced “shimmering” and “watery” sounds.
Options: Chorus 2-Voice, Chorus 4-Voice
Chorus 2-Voice
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Delay
0–100
20
Amount
0–100
80
Width
0–100
80
Feedback
0–100
50
Rate
0–100
10
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Delay
0–100
20
Amount
0–100
80
Width
0–100
80
Feedback
0–100
50
Rate
0–100
10
Chorus 4-Voice
Autopans
This effect uses an LFO to move the incoming signal back and forth across the stereo field, creating a rotary effect.
Options: Autopan, Autopan Sync
Autopan
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Rate
0–100
10
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Rate
8 bars – 1/32
1/4
Autopan Sync
304
Tremolos
This effect uses an LFO to increase and decrease the volume of the signal. Depending on the LFO shape, this can
produce a smooth wave effect (sine wave) or a stuttering “on-off” effect (square wave).
Options: Tremolo, Tremolo Sync
Tremolo
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Rate
0–100
10
Sine to Square 0–100 (sine–square) 0
Tremolo Sync
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Rate
1 bar – 1/16 triplets
1/4
Sine to Square 0–100 (sine–square) 0
Phasers
The phaser is a classic effect, created by multiple ganged all-pass filters to create “notches,” or sharp spikes, in the
frequency spectrum. The frequencies of these all-pass filters are usually modulated by an LFO to create a sweeping
sound.
Options: Phaser 1, Phaser 2, Phaser Sync
Phaser 1
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Rate
0–100
10
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Rate
0–100
10
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Rate
1 bar – 1/16 triplets
1/4
Phaser 2
Phaser Sync
305
HP (High-Pass) Filters
Options: HP Filter, HP Filter Sweep, HP Filter Sync, HP Shelving Filter
HP Filter
This effect is a static filter without modulation.
Parameter
Value Range
Default Value
Frequency
10–19999 Hz
1500
Resonance
0–100
0
HP Filter Sweep
This effect is a high-pass filter with its cutoff frequency
modulated by an LFO.
HP Filter Sync
This effect is a high-pass filter with its cutoff frequency
modulated by an LFO.
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
80
Low Frequency 0–100
50
High Frequency 0–100
100
Resonance
0–100
33
Rate
0–100
10
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Low Frequency 0–100
0
High Frequency 0–100
100
Resonance
0–100
50
Rate
8 bars – 1/32
1/4
Value Range
Default Value
10–19999 Hz
1500
Resonance
0–100
0
Gain
-18.0 – 18.0 dB
0.0
HP Shelving Filter
This filter differs from the standard filter type, as it attenuates Parameter
all frequencies after the cutoff point equally.
Frequency
306
LP (Low-Pass) Filters
Options: LP Filter, LP Filter Sweep, LP Filter Sync, LP Shelving Filter
LP Filter
This effect is a static filter without modulation.
LP Filter Sweep
This effect is a low-pass filter with its cutoff frequency
modulated by an LFO.
LP Filter Sync
This effect is a low-pass filter with its cutoff frequency
modulated by an LFO.
Parameter
Value Range
Default Value
Frequency
10–19999 Hz
1500
Resonance
0–100
0
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
80
Low Frequency 0–100
0
High Frequency 0–100
100
Resonance
0–100
33
Rate
0–100
10
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Low Frequency 0–100
0
High Frequency 0–100
100
Resonance
0–100
50
Rate
8 bars – 1/32
1/4
Value Range
Default Value
10–19999 Hz
1500
Resonance
0–100
0
Gain
-18.0 – 18.0 dB
0.0
LP Shelving Filter
This filter differs from the standard filter type, as it attenuates Parameter
all frequencies after the cutoff point equally.
Frequency
307
Parametric EQs
Options: PEQ 2-Band, 2-Shelf, PEQ 4-Band
PEQ 2-Band, 2-Shelf
This effect is a combination of one two-band parametric
equalizer and two shelving filters.
Parameter
Value Range
Default Value
Low Frequency
22–1000 Hz
220
Frequency 1
82–3900 Hz
820
Frequency 2
220–10000 Hz
2200
High Frequency
560–19999 Hz
5600
Q1
0–100
0
Q2
0–100
0
Low Gain
-18.0 – 18.0 dB
0.0
Gain 1
-18.0 – 18.0 dB
0.0
Gain 2
-18.0 – 18.0 dB
0.0
High Gain
-18.0 – 18.0 dB
0.0
PEQ 4-Band
This effect is a powerful four-band parametric equalizer with
four independent EQ ranges.
Parameter
Value Range
Default Value
Low Frequency
22–1000 Hz
220
Frequency 1
82–3900 Hz
820
Frequency 2
220–10000 Hz
2200
High Frequency
560–19999 Hz
5600
Q1
0–100
5
Q2
0–100
5
Q3
0–100
5
Q4
0–100
5
Gain 1
-18.0 – 18.0 dB
0.0
Gain 2
-18.0 – 18.0 dB
0.0
Gain 3
-18.0 – 18.0 dB
0.0
Gain 4
-18.0 – 18.0 dB
0.0
308
Distortions
Options: Distortion Amp, Distortion Fuzz, Distortion Grimey, Distortion Overdrive, Distortion Custom
Distortion Amp
This effect is designed to reproduce the sound of a tube
amplifier at high volumes.
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Drive
0–100
50
Tone
0–100
50
Dynamics
0–100
50
Output
0–100
50
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Drive
0–100
50
Output
0–100
50
Low
0–100
50
Low-Mid
0–100
50
High-Mid
0–100
50
High
0–100
50
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Drive
0–100
50
Grime
0–100
50
Center
0–100
50
Width
0–100
50
Resonance
0–100
50
Output
0–100
50
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Drive
0–100
50
Tone
0–100
50
Output
0–100
50
Distortion Fuzz
This popular effect uses hard clipping of the audio signal,
which, at extreme settings, can turn a standard waveform
into a square wave, producing a “razor” effect.
Distortion Grimey
This is a unique distortion effect that distorts a frequency
range in a selectable band.
Distortion Overdrive
This distortion is designed to sound like a mildly distorting
amplifier at medium volumes. It is the smoothest distortion
type available.
309
Distortion Custom
This effect is a highly customized distortion, capable of a
wide range of useable sounds.
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Drive
0–100
50
+Soft
5–75
2
+Clip
5–50
25
–Soft
5–75
2
–Clip
5–50
25
Low
-18.0 – 18.0 dB
0.0
Mid
-18.0 – 18.0 dB
0.0
High
-18.0 – 18.0 dB
0.0
Output
-18.0 – 18.0 dB
50
Compressors
A compressor is an effect that changes the dynamic range of a signal by automatically reducing its gain.
Options: Compressor Master, Compressor Opto, Compressor VCA, Compressor Vintage
Compressor Master
This is the most transparent compressor, able to perform
substantial volume adjustments without artifacts.
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Attack
0–100
50
Release
0–100
50
Threshold
-50 – 0 dB
0
Ratio
1–20
1
Oldskool
Off, On
Off
Output
-6 – 24 dB
0
Value Range
Default Value
0–100 (dry–wet)
100
-6 – 18 dB
0
0–100
50
Release
0–100
50
Threshold
-50 – 0 dB
0
Ratio
1–20
1
Knee
1–100
1
Output
-6 – 24 dB
0
Compressor Opto
The Opto Compressor is modeled after a vintage
Parameter
compressor type using an optical circuit to control the
volume reduction of the input signal. These compressors are Dry/Wet
usually associated with soft and unobtrusive attack and
Input
release characteristics.
Attack
310
Compressor VCA
This compressor is more modern-sounding, with a slightly
more transparent sound. A VCA Compressor tends to have
quicker attack and release times than an Opto Compressor.
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Input
-6 – 18 dB
0
Attack
0–100
50
Release
0–100
50
Threshold
-50 – 0 dB
0
Ratio
1–20
1
Knee
1–100
1
Output
-6 – 24 dB
0
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Input
-6 – 18 dB
0
Attack
0–100
50
Release
0–100
50
Threshold
-50 – 0 dB
0
Ratio
1–20
1
Knee
1–100
1
Output
-6 – 24 dB
0
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Decimate
0–100
0
Bit Reducer
4–32
32
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Rate
0–100
0
Decimate
0–100
0
Compressor Vintage
This compressor has a sound similar to classic tube
compressors, with their gentle yet pumping response and a
dash of tube saturation.
Bit Reducers
Options: Decimator, Resampler
Decimator
Decimator down-samples the incoming signal by removing
bits from the digital signal. The difference between
decimation and resampling is that Decimator does not use
any filtering to mask or correct digital artifacts. The result is
an effect ranging from mild to almost completely pure digital
distortion, depending on the setting and the source material.
Resampler
Resampler is similar to Decimator in that it removes bits from
an incoming signal. The difference is that Resampler applies
a complex suite of filters and anti-aliasing to attempt to
retain the original sound quality. This is a method used by
popular vintage samplers and sampling drum machines from
the 1980s. Resampler can be used to achieve a “dirty”
sound on drum loops, without the harshness of distortion.
311
Other
Options: Auto Wah, Frequency Shifter, Transient Shaper
Auto Wah
This effect is a low-pass filter modulated by an envelope that Parameter
yields a classic funky “wah-wah”- like sound. The envelope
is triggered by the incoming signal’s amplitude. The amount Dry/Wet
of the envelope on the cutoff frequency is user-definable.
Resonance
Value Range
Default Value
0–100 (dry–wet)
100
0–100
75
Attack
0–100
30
Release
0–100
30
Center
0–100
50
Sensitivity
0–100
50
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Frequency
-1000 – 1000
0
Asynchrony
0–1000
0
A Pan
0–100
0
B Pan
0–100
100
A Gain
0–100
75
B Gain
0–100
75
Parameter
Value Range
Default Value
Dry/Wet
0–100 (dry–wet)
100
Attack
0–100
50
Release
0–100
50
Output
0–100
50
Frequency Shifter
A frequency shifter changes the frequencies of an input
signal by a fixed amount and alters the relationship of the
original harmonics. This can produce a chorus-like effect as
well as very crazy artificial timbres.
Transient Shaper
A transient shaper can be used to enhance or soften the
Attack and Release phases of audio material.
312
Glossary
This glossary briefly defines and explains many of the technical terms used throughout this manual.
Aftertouch
The majority of contemporary keyboards are capable of generating aftertouch messages. On this
type of keyboard, when you press harder on a key you are already holding down, a MIDI aftertouch
message is generated. This feature makes sounds even more expressive (e.g., through vibrato).
Aliasing
Aliasing is an audible side effect arising in digital systems as soon as a signal contains harmonics
higher than half the sampling frequency.
Amount
Describes to which extent a modulation source influences a given parameter.
Amplifier
An amplifier is a component that influences the volume level of a sound via a control signal. It
can be modulated by a control signal (e.g., generated by an envelope or an LFO).
Attack
An envelope parameter. This term describes the ascent rate of a time-relevant process (e.g., an
envelope from its starting point to the point where it reaches its highest value). The attack phase
is initiated immediately after a trigger signal is received (e.g., after you play a note on a trigger
pad or a keyboard).
Bit Rate
Bit rate (also known as word length), is the number of bits used to store the level information of
each single sample slice within a whole sample. The higher the bit rate, the more precise the
information about a sample (i.e., its dynamics’ resolution). Normal audio CDs are 16-bit. The
MPC hardware supports full 24-bit resolution.
Bounce
When you “bounce” a sequence, track, or program, you are rendering that part of your project as
an audio file (as opposed to a MIDI file). The MPC hardware lets you bounce sequences, tracks,
or programs as samples (saved to your project’s sample pool) or as full audio tracks (saved to
your project’s sample pool and added directly to the current sequence).
Bouncing a track will render that track after it is sent through its program. Bouncing a program
will render all tracks that use that program after they are sent through it. Bouncing a sequence
will render all tracks in that sequence after they are sent through their respective programs.
Clipping
Clipping is a sort of distortion that occurs when a signal exceeds the maximum value that can be
handled by a signal processing system it is fed into. The curve of a clipped signal is dependent
on the system where the clipping occurs. In the analog domain, clipping effectively limits the
signal to a given maximum level. In the digital domain, clipping is similar to a numerical overflow,
resulting in negative polarity of the signal’s portions exceeding the maximum level.
Control Change
MIDI messages enable you to manipulate the behavior of a sound generator to a significant
degree. This message essentially consists of two components:
(Controllers)
•
The controller number, which defines the parameter to be influenced. It can range from 0
to 127.
•
The controller value, which determines the extent of the modification.
Controllers can be used for effects such as slowly swelling vibrato, changing the stereo panning
position and influencing filter frequency.
Cutoff
The cutoff frequency is a significant factor for a filter. A low-pass filter for example dampens the
portion of the signal that lies above this frequency. Frequencies below this value are allowed to
pass through without being processed.
313
CV
CV stands for control voltage, an analog method of sending control messages to external
synthesizers, drum machines, etc. CV messages are typically used in conjunction with Gate
messages (CV messages determine the pitch of notes while Gate messages determine note
activation and length). CV messages are sent from the CV out ports of your MPC hardware and
to the CV in ports of your external MIDI device.
Please note that each external MIDI device uses a specific control voltage range, which
determines how many volts are used in each octave (e.g., 1V/oct). Be mindful of this when
setting it up with the MPC software and/or controller hardware—mismatched voltage ranges can
produce unusual/undesirable “re-scaling” of the octaves.
Decay
Decay describes the descent rate of an envelope once the attack phase has reached its
maximum and the envelope drops to the level defined by the sustain value.
Envelope
An envelope is used to modulate a sound-shaping component within a given time. For instance,
an envelope that modulates the cutoff frequency of a filter opens and closes this filter over a
period of time. An envelope is started via a trigger, usually a MIDI note.
The classic ADSR envelope consists of four individually variable phases: attack, decay, sustain,
and release. Attack, decay and release are time or slope values, while sustain is an adjustable
level. Once an incoming trigger is received, the envelope runs through the attack and decay
phases until it reaches the programmed sustain level. This level remains constant until the trigger
is terminated. The envelope then initiates the release phase until it reaches the minimum value.
You can see and read about the envelopes used in MPC Live in Operation > Modes > Program
Edit Mode > Anatomy of an Envelope.
Filter
A filter is a component that allows some of a signal’s frequencies to pass through it and
dampens other frequencies. The most important aspect of a filter is the filter cutoff frequency.
Filters generally come in four categories: low-pass, high-pass, band-pass, and band-stop.
These are the available filters:
A low-pass filter (the most common type) dampens all frequencies above the cutoff frequency.
A high-pass filter in turn dampens the frequencies below the cutoff.
A band-pass filter allows only those frequencies around the cutoff frequency to pass. All
others are dampened.
A band-stop filter does the opposite of a band-pass: it dampens only the frequencies around
the cutoff frequency.
A band-boost filter boosts the frequencies around the cutoff frequency, similar to what a band
on an equalizer would do. All other frequencies pass through normally.
The number of poles in a filter’s “slope” determines how extreme or subtle the effect of the
filter will be. Filters with one or two poles produce a subtler sound while filters with six or eight
poles are much more pronounced.
The Model filters are analog-style emulations of famous vintage synth filters. Model1 is a fourpole filter that distorts at high input levels. Model2 uses a mellow resonance with a “fattening”
distortion in the lower frequencies. Model3 can produce howling, piercing resonances and
extreme sub frequencies—watch your speakers!
The Vocal filters are formant filters that emulate the human voice. Vocal1 produces “ah” and
“ooh” vowel sounds. Vocal2 uses three bands to produce “oh” and “ee” vowel sounds.
Vocal3 uses five bands to emulate an idealized model of the vocal tract.
MPC3000 LPF is a dynamic, resonant low-pass filter (12 dB/oct) that was used on the original
MPC3000, released in 1994.
Please also see the entry for Resonance, an essential characteristic of a filter’s sound.
Gate
Gate messages are analog messages sent to external synthesizers, drum machines, etc. Gate
messages are typically used in conjunction with CV messages (CV messages determine the pitch
of notes while Gate messages determine note activation and length). Gate messages are sent from
the CV out ports of your MPC hardware and to the CV/Gate in ports of your external MIDI device.
314
LFO
LFO is an acronym for low-frequency oscillator. The LFO generates a periodic oscillation at
a low frequency and features variable waveshapes. Similar to an envelope, an LFO can be
used to modulate a sound-shaping component.
MIDI
MIDI stands for musical instrument digital interface. Developed in the early 1980s, MIDI
enables interaction between various types of electronic music instruments from different
manufacturers. At the time a communications standard for heterogeneous devices did not
exist, so MIDI was a significant advance. It made it possible to link various devices with one
another through simple, standardized connectors.
Essentially, this is how MIDI works: One sender is connected to one or several receivers. For
instance, if you want to use a computer to play a MIDI synthesizer, the computer is the sender
and the synthesizer acts as the receiver. With a few exceptions, the majority of MIDI devices
are equipped with two or three ports for this purpose: MIDI In, MIDI Out and in some cases
MIDI Thru. The sender transfers data to the receiver via the MIDI Out jack. Data are sent via a
cable to the receiver’s MIDI In jack.
MIDI Thru has a special function. It allows the sender to transmit to several receivers. It routes
the incoming signal to the next device without modifying it. Another device is simply
connected to this jack, thus creating a chain through which the sender can address a number
of receivers. Of course, it is desirable for the sender to be able to address each device
individually. To achieve this, a MIDI channel message is sent with each MIDI event.
MIDI Channel
This is a very important element of most messages. A receiver can only respond to incoming
messages if its receive channel is set to the same channel as the one the sender is using to
transmit data. Subsequently, the sender can address specific receivers individually. MIDI
Channels 1–16 are available for this purpose.
MIDI Clock
The MIDI clock message transmits real-time tempo information to synchronize processes
among several connected devices (e.g., a sound generator’s delay time to a MIDI sequencer).
Modulation
A modulation influences or changes a sound-shaping component via a modulation source.
Modulation sources include envelopes, LFOs or MIDI messages. The modulation destination
is a sound-shaping component such as a filter or a VCA.
Note On & Note Off This is the most important MIDI message. It determines the pitch and velocity of a generated
note. A note-on message will start a note. Its pitch is derived from the note number, which
can range from 0 to 127. The velocity ranges from 1 to 127. A velocity value of 0 is equivalent
to a note-off message.
Normalize
Normalization is a function to raise the level of a sample to its maximum (0 dB) without
causing distortion. This function automatically searches a sample for its maximum level and
consequently raises the entire sample’s level until the previously determined maximum level
reaches 0 dB. In general, this results in a higher overall volume of the sample.
Panning
The process or the result of changing a signal’s position within the stereo panorama.
Pitch-Bend
Pitch-bend is a MIDI message. Although pitch-bend messages are similar in function to
control change messages, they are a distinct type of message. The resolution of a pitch-bend
message is substantially higher than that of a conventional controller message. The human
ear is exceptionally sensitive to deviations in pitch, so the higher resolution is used because it
relays pitch-bend information more accurately.
315
Program
A program is a file that contains a list of all samples to be used, and settings for each sample
(e.g., pad assignments, loop points, pitch tuning, effects, etc.) Program Edit Mode is where
you can edit and assign samples (read more about this in Operation > Modes > Program
Edit Mode). You can have a total of 128 programs in a project.
There are three kinds of programs that use samples for their sound source. Drum programs
are mostly used for creating drum programs and easy and quick assigning of samples to a
pad. With keygroup programs, you can use one sample (or more) and spread it across two or
more keys and play the sample chromatically over a keyboard. That way, there is no need to
sample every key of, for instance, a piano. Clip programs use several samples that can be
looped (clips), each of which can assigned to a pad; launching different combinations of clips
together lets you create intriguing, layered performances.
Program Change
These are MIDI messages that select sound programs. Programs 1–128 can be changed via
program change messages.
Release
An envelope parameter. This term describes the descent rate of an envelope to its minimum
value after a trigger is terminated. The release phase begins immediately after the trigger is
terminated, regardless of the envelope’s current status. For instance, the release phase may
be initiated during the attack phase.
Resonance
Resonance or emphasis is an important filter parameter. It emphasizes the frequencies around
the filter cutoff frequency by amplifying them with a narrow bandwidth. This is one of the most
popular methods of manipulating sounds. If you increase the emphasis to a level where the
filter enters a state of self-oscillation, it will generate a relatively pure sine waveform.
Root Key
The root key defines the original pitch of a recorded instrument or of a sample. Samples in
MPC contain the dedicated root key information. This information will be created
automatically during recording or importing.
Sample
When you tap the pads on your MPC hardware, you can trigger sounds that we call
samples. Samples are digitized snippets of audio that can be recorded using the recording
(sampling) function of your MPC hardware or loaded from the Browser.
You can edit and process a sample in different ways. For example, a sample can be
trimmed, looped, pitch-shifted or processed, using various effects. When you have finished
editing your sample, you can assign it to one or more drum pads to play it. Samples can be
either mono or stereo.
Sample Rate
This is the frequency representing the amount of individual digital sample scans per second
that are taken to capture an analog signal digitally. For normal CD audio recordings, 44100
samples per second are used, also written as 44.1 kHz.
You can export audio using sampling rates up to 96 kHz (see Operation > General Features
> Audio Mixdown) and play audio using 44.1 kHz.
Sequence
A sequence is the most basic “building block” of music you can create within an MPC
project. MIDI information from your MPC hardware pads, buttons, and Q-Link knobs are
recorded to the tracks of a sequence. Each sequence on your MPC hardware can contain
128 MIDI tracks and 8 audio tracks. Each project can store up to 128 separate sequences.
The length of a sequence can be set from 1 to 999 bars, which would be enough to create an
entire song using only one sequence. However, MPC Live has a dedicated Song Mode that
lets you chain sequences together to create a song.
Song
Song Mode that allows you to arrange different sections (verse, chorus, hook, etc.) in order
to build a song. Each song can have up to 999 “steps” (stages in which a sequence may play
one or more times). Each project can store up to 32 songs.
316
Stretch Factor
The stretch factor is a value generated by the Warp algorithm in the software. When you
record an audio file, the current sequence tempo will be embedded with it. This information
is stored within the sample file when you save the project. When you warp an audio track
region, the warping algorithm uses this sequence tempo and the current value in the BPM
field to generate the stretch factor.
Sustain
This term describes the level of an envelope remaining constant after it has passed the attack
and decay phases. Once reached, the sustain level is kept until the trigger is terminated.
Time-Stretch
See Warp below.
Track
A sequence on your MPC hardware can contain 128 MIDI tracks and 8 audio tracks.
Each MIDI track contains MIDI note events and controller data. In this case, the track
contains no audio information—only MIDI information that uses the samples in a program (or
an external MIDI sound module) to generate its audio. You can edit your performance in
many different ways once the performance has been captured.
Each audio track contains an audio signal that has been recorded or imported into your
project. You can edit this audio within the software and incorporate it into your sequences
alongside your MIDI tracks.
Trigger
A trigger is a signal that initiates events. Trigger signals are very diverse. For instance, a MIDI
note or an audio signal can be used as a trigger. The events a trigger can initiate are also
very diverse. A common application for a trigger is its use to start an envelope.
Warp
The Warp feature lengthens or shortens a region of an audio track or sample without
changing its pitch. This enables you to fit the length of an audio track or sample to the length
of a sequence, a bar in your sequence, etc. while maintaining its original key.
Please note that the Warp algorithms are very CPU-intensive and can result in audio dropouts during playback if used too freely. Be mindful of how (and how often) you use the warp
function. You can reduce the CPU resources required by doing any/all of the following:
Minimize the amount of pitch adjustment of warped audio.
In Program Edit Mode, avoid using extreme Stretch values.
Avoid warping very small audio regions.
Warp as few tracks or track regions as possible (i.e., reduce the number of total number
of voices of the polyphonic limit that use the Warp algorithm at a given time), especially
instances where the warped regions start at the same time.
Avoid rapidly triggering samples that are warped.
If you have warped samples used in a drum program, consider using the Flatten Pad
function to consolidate the affected pad’s layers into one audio sample (see here to learn
about this). After you flatten the pad, its sample/samples no longer need to be warped.
317
SATA Drive Installation
To create more internal storage space on your MPC hardware, you can purchase a SATA (Serial ATA) drive and
install it yourself, but read this chapter first.
Your MPC X or MPC Live can support nearly any standard 2.5” SATA drive on the market—either a solid-state drive
(SSD) or hard-disk drive (HDD). Make sure it uses a 2.5” (63.5 mm) form factor and uses (or can use) one of these file
systems: exFAT, FAT32, NTFS, or EXT4 (for read and write capability) or HFS+ (for read-only capability).
Note: We recommend using an exFAT file system as it is the most robust one supported by both Windows and macOS.
Note: Alternatively, you could install an mSATA (mini-SATA) drive, but make sure you also purchase an adapter that
enables it to fit into a typical 2.5” SATA interface.
1. Make sure your MPC hardware is powered off.
2. Locate the SATA drive panel in the center of the bottom panel of your MPC hardware. Use a Phillips-head
screwdriver to remove the screws (don’t lose them!), and remove the SATA drive panel.
3. Gently pull the SATA connector and cable out from inside your MPC hardware. Be careful not to disturb
anything inside—handle just the SATA connector and cable.
4. Connect your SATA drive to the SATA connector. Make sure the connection is secure.
5. Use four 3x5mm mounting screws (included with MPC hardware or with your SATA drive) to secure the SATA drive
to the SATA drive panel. Do not overtighten the screws, but make sure the drive is secure and does not shake.
6. Place the SATA drive panel back onto the bottom panel of your MPC hardware, and use the original screws to
secure it in place.
You can now access this drive while using your MPC hardware!
In Standalone Mode, this drive will appear as a second internal drive.
In Controller Mode, this drive will appear as another drive connected to your computer (just as a USB drive or SD
card connected does when connected to your MPC hardware).
318
MIDI Machine Control (MMC)
Your MPC hardware can send and receive MIDI Machine Control (MMC) messages, a standard protocol for transport
controls.
The MPC hardware can send these messages:
MPC Button
MMC Command Sent
Rec
MMC Record Strobe (when recording starts), then MMC Record Exit
Overdub
MMC Record Strobe (when recording starts), then MMC Record Exit
Stop
MMC Stop
Play
MMC Deferred Play
Play Start
MMC Locate Zero, then Deferred Play
Data Dial, –/+, Step </>, Bar <</>>
MMC Locate values
To set up your MPC hardware to send MMC messages to an external device:
1. Use a standard 5-pin MIDI cable to connect your MPC hardware’s MIDI Out A to the MIDI input of your external
device.
2. Press Menu to show the menu, and tap the gear icon to enter the Preferences.
3. Tap the Sync tab.
4. Tap the Send Port 1 field, and use the data dial or –/+ buttons to select Midi Out A.
5. Tap the Send MMC box so it is enabled (checked).
6. Exit the Preferences.
7. Configure your other device properly so it can receive MMC messages.
The MPC hardware can receive these messages:
MPC Command Received
MPC Function
MMC Deferred Play
Play
MMC Locate Zero, then Deferred Play
Play Start
MMC Stop
Stop
MMC Record Strobe
Record (Rec)
MMC Pause
Stop
MMC Locate values
Change location in sequence
To set up your MPC hardware to receive MMC messages from an external device:
1. Use a standard 5-pin MIDI cable to connect your MPC hardware’s MIDI In A to the MIDI output of your external
device.
2. Press Menu to show the menu, and tap the gear icon to enter the Preferences.
3. Tap the Sync tab.
4. Tap the Receive MMC box so it is enabled (checked).
5. Exit the Preferences.
6. Configure your other device properly so it can send MMC messages.
319
Technical Specifications
Specifications are subject to change without notice.
MPC X
ADCs
24-bit @ 44.1, 48, or 96 kHz
DACs
24-bit @ 44.1, 48, or 96 kHz
Digital Signal Processing
32-bit floating point
Mic Inputs 1–2
Dynamic Range
112 dB (A-weighted)
(2) balanced XLR+1/4”
(6.35 mm) TRS
SNR
111 dB (1 kHz, +4 dBu, A-weighted)
THD+N
0.003% (1 kHz, +4 dBu, -1 dBFS)
Preamp EIN
-135 dBu (max gain, 40 Ω source, A-weighted)
Digital Audio System
-129.5 dBu (max gain, 150 Ω source, unweighted)
Frequency Response
20 Hz – 20 kHz (+0.2 / -0.2 dB)
Maximum Input Level
+12.5 dBu
Sensitivity
-46 dBu
Gain Range
58 dB
Line Inputs 1–2
Dynamic Range
114 dB (A-weighted)
(2) balanced XLR+1/4”
(6.35 mm) TRS
SNR
112 dB (1 kHz, +4 dBu, A-weighted)
THD+N
0.003% (1 kHz, +4 dBu, -1 dBFS)
Frequency Response
20 Hz – 20 kHz (+0.1 / -0.1 dB)
Maximum Input Level
+20 dBu
Sensitivity
-9.5 dBu
Gain Range
29.5 dB
Line Inputs 3–4
Dynamic Range
114.5 dB (A-weighted)
(2) balanced 1/4”
(6.35 mm) TRS
SNR
112.5 dB (1 kHz, +4 dBu, A-weighted)
THD+N
0.003% (1 kHz, +4 dBu, -1 dBFS)
Frequency Response
20 Hz – 20 kHz (+0.1 / -0.1 dB)
Maximum Input Level
+20 dBu
Sensitivity
-10 dBu
Gain Range
30 dB
Inst Inputs 1–2
Dynamic Range
113.5 dB (A-weighted)
(2) unbalanced 1/4”
(6.35 mm) TS
SNR
111.5 dB (1 kHz, +4 dBu, A-weighted)
THD+N
0.003% (1 kHz, +4 dBu, -1 dBFS)
Frequency Response
20 Hz – 20 kHz (+0.1 / -0.2 dB)
Maximum Input Level
+10 dBu
Sensitivity
-20 dBu
Gain Range
30 dB
Input Impedance
~ 1 MΩ
320
Phono Inputs
Dynamic Range
108 dB (A-weighted, 63 mVrms @ 1kHz, -1 dBFS, 20 Ω source)
(2) unbalanced RCA
SNR
86 dB (A-weighted, 4 mVrms @ 1kHz, 20 Ω source)
THD+N
0.005% (1 kHz, -46 dBu, -1 dBFS)
Maximum Input Level
63 mVrms (1 kHz)
Sensitivity
2 mVrms (1 kHz)
Master Outputs 1–2
Dynamic Range
114 dB (A-weighted)
(2) impedance-balanced
1/4” (6.35 mm) TRS
THD+N
0.006% (1 kHz, -1 dBFS)
Frequency Response
20 Hz – 20 kHz (+0.0 / -0.2 dB)
Maximum Input Level
+20 dBu
Sensitivity
51 Ω
Outputs 3–4
Dynamic Range
114 dB (A-weighted)
(2) impedance-balanced
1/4” (6.35 mm) TRS
THD+N
0.006% (1 kHz, -1 dBFS)
Frequency Response
20 Hz – 20 kHz (+0.0 / -0.2 dB)
Maximum Input Level
+20 dBu
Sensitivity
51 Ω
Outputs 5–8
Dynamic Range
118.5 dB (A-weighted)
(4) impedance-balanced
1/4” (6.35 mm) TRS
THD+N
0.001% (1 kHz, -1 dBFS)
Frequency Response
20 Hz – 20 kHz (+0.1 / -0.0 dB)
Maximum Input Level
+20 dBu
Sensitivity
51 Ω
Headphone Outputs
Dynamic Range
111 dB (A-weighted)
(1) 1/4” (6.35 mm)
stereo headphone
THD+N
0.007% (1 kHz, -1 dBFS, 10 mW/channel into 32 Ω headphones)
(1) 1/8” (3.5 mm)
stereo headphone
Frequency Response
20 Hz – 20 kHz (+0.0 / -0.2 dB)
Maximum Power Delivered
360 mW (<1% THD)
Maximum Output Level
+20 dBu
321
Mechanical
Pads
(16) velocity- and pressure-sensitive pads, RGB-backlit
(8) banks accessible via Pad Bank buttons
Knobs
(16) 360° touch-sensitive Q-Link knobs for parameter adjustment
(7) 270° knobs for gain, mix & level adjustment
(1) 360° encoder for value/data adjustment
Memory
File System Compatibility
Display
10.1” (25.6 cm) full-color 1280x800 display with capacitive multi-touch
RAM
2 GB
Internal
Storage
16 GB (6 GB user storage + 10 GB pre-installed content)
Expandable via SATA connections
exFAT (read & write) (recommended)
FAT32 (read & write)
NTFS (read & write)
EXT4 (read & write)
HFS+ (read only)
Audio Files: AIF/AIFF, FLAC, MP3, OGG, WAV
Connections
(2) XLR+1/4” (6.35 mm) TRS inputs (Input 1/2)
(2) 1/4” (6.35 mm) TRS inputs (Input 3/4: 1 stereo pair)
(2) 1/4” (6.35 mm) TS instrument inputs (Inst 1/2)
(2) RCA inputs (Input 3/4: 1 stereo pair, phono- or line-level)
(2) 1/4” (6.35 mm) TS footswitch inputs (FS 1/2)
(2) 5-pin MIDI inputs
(8) 1/4” (6.35 mm) TRS outputs (Main L/R, Outputs 3/4–7/8: 4 stereo pairs)
(4) 5-pin MIDI outputs
(8) 1/8” (3.5 mm) CV/Gate outputs
(1) 1/4” (6.35 mm) stereo headphone output
(1) 1/8” (3.5 mm) stereo headphone output
(2) USB Type-A ports
(1) USB Type-B port
(1) SD card slot
(1) power adapter input
Power
via power adapter: 19 V, 3.42 A, center-positive, included
Dimensions
19.9” x 16.7” x 3.4” / 50.5 x 42.4 x 8.7 cm (display flat)
(width x depth x height)
19.9” x 15.3” x 8.4” / 50.5 x 38.8 x 21.4 cm (display upright)
Weight
12.57 lb.
5.66 kg
322
MPC Live
ADCs
24-bit @ 44.1, 48, or 96 kHz
DACs
24-bit @ 44.1, 48, or 96 kHz
Digital Signal Processing
32-bit floating point
Line Inputs
Dynamic Range
113.5 dB (A-weighted)
(2) balanced
1/4” (6.35 mm) TRS
SNR
108 dB (1 kHz, +4 dBu, A-weighted)
THD+N
0.001% (1 kHz, +4 dBu, -1 dBFS)
Frequency Response
20 Hz – 20 kHz (+0.0 / -0.1 dB)
Maximum Input Level
+11 dBu
Sensitivity
-13.5 dBu
Gain Range
24.5 dB
Phono Inputs
Dynamic Range
107 dB (A-weighted, 63 mVrms @ 1 kHz, -1 dBFS, 20 Ω source)
(2) unbalanced RCA
SNR
86 dB (A-weighted, 4 mVrms @ 1 kHz, 20 Ω source)
THD+N
0.009% (1 kHz, -46 dBu, -1 dBFS)
Maximum Input Level
63 mVrms (1 kHz)
Sensitivity
2 mVrms (1 kHz)
Master Outputs 1–2
Dynamic Range
113 dB (A-weighted)
(2) impedance-balanced
1/4” (6.35 mm) TRS
THD+N
0.002% (1 kHz, -1 dBFS)
Frequency Response
20 Hz – 20 kHz (+0.0 / -0.5 dB)
Maximum Input Level
+9 dBu
Sensitivity
51 Ω
Outputs 3–6
Dynamic Range
116 dB (A-weighted)
(4) impedance-balanced
1/4” (6.35 mm) TRS
THD+N
0.001% (1 kHz, -1 dBFS)
Frequency Response
20 Hz – 20 kHz (+0.0 / -0.1 dB)
Maximum Input Level
+9 dBu
Sensitivity
51 Ω
Headphone Output
Dynamic Range
112 dB (A-weighted)
(1) 1/8” (3.5 mm)
stereo headphone
THD+N
0.005% (1 kHz, -1 dBFS, 10 mW/channel into 32 Ω headphones)
Frequency Response
20 Hz – 20 kHz (+0.0 / -0.2 dB)
Maximum Power Delivered
+35 mW (<1% THD, 32 Ω headphones)
Maximum Output Level
+10 dBu
Digital Audio System
323
Mechanical
Pads
(16) velocity- and pressure-sensitive pads, RGB-backlit
(8) banks accessible via Pad Bank buttons
Knobs
(4) 360° touch-sensitive Q-Link knobs
(4) Q-Link knob columns accessible via Q-Link button
(1) 360° encoder for value/data adjustment and selection via push
Memory
File System Compatibility
Display
7” (17.8 cm) full-color 1280x800 display with capacitive multi-touch
RAM
2 GB
Internal
Storage
16 GB (6 GB user storage + 10 GB pre-installed content)
Expandable via SATA connections
exFAT (read & write) (recommended)
FAT32 (read & write)
NTFS (read & write)
EXT4 (read & write)
HFS+ (read only)
Audio Files: AIF/AIFF, FLAC, MP3, OGG, WAV
Connections
(2) 1/4” (6.35 mm) TRS inputs (1 stereo pair)
(6) 1/4” (6.35 mm) TRS outputs (3 stereo pairs)
(1) 1/8” (3.5 mm) stereo headphone output
(2) RCA inputs (1 stereo pair)
(2) 5-pin MIDI inputs
(2) 5-pin MIDI outputs
(2) USB Type-A ports
(1) USB Type-B port
(1) SD card slot
(1) power adapter input
Power
via power adapter: 19 V, 3.42 A, center-positive, included
via battery: lithium-ion, rechargeable, up to 6 hours of battery life
Dimensions
16.7” x 8.8” x 2.7”
(width x depth x height)
42.4 x 22.4 x 6.9 cm
Weight
5.9 lb.
2.7 kg
324
MPC Touch
Line Inputs
Dynamic Range
102 dB (A-weighted)
(2) balanced
1/4” (6.35 mm) TRS
SNR
99 dB (1 kHz, +4 dBu, A-weighted)
THD+N
0.002% (1 kHz, +4 dBu, -1 dBFS)
Frequency Response
20 Hz – 20 kHz (+0.1 / -0.1 dB)
Maximum Input Level
+15 dBu
Input Impedance
12 KΩ (balanced), 5 KΩ (unbalanced)
Sensitivity
-16 dBu
Gain Range
31 dB
Main Outputs
Dynamic Range
100 dB (A-weighted)
(2) impedancebalanced 1/4”
(6.35 mm) TRS
THD+N
0.006% (1 kHz, -1 dBFS)
Frequency Response
20 Hz – 20 kHz (+0.25 / -0.25 dB)
Maximum Input Level
+8 dBu
Output Impedance
100 Ω
Headphone Output
THD+N
0.009% (1 kHz, -1 dBFS, 10 mW/channel into 32 Ω headphones)
(1) 1/8” (3.5 mm)
stereo headphone
Frequency Response
20 Hz – 20 kHz (+0.3 / -0.3 dB)
Maximum Output Level
+6 dBu
Maximum Power Delivered 12 mW/channel
Mechanical
Output Impedance
33 Ω
Pads
(16) velocity- and pressure-sensitive pads, RGB-backlit
(8) banks accessible via Pad Bank buttons
Knobs
(4) 360° touch-sensitive Q-Link knobs
(4) Q-Link knob columns accessible via Q-Link button
(1) 360° encoder for value/data adjustment and selection via push
Display
Connections
7.0” (17.8 cm) full-color 1280x800 display with capacitive
multi-touch
(2) 1/4” (6.35 mm) TRS inputs (1 stereo pair)
(2) 1/4” (6.35 mm) TRS outputs (1 stereo pair)
(1) 1/8” (3.5 mm) stereo headphone output
(1) 1/8” (3.5 mm) MIDI input (1/8”-to-5-pin adapter included)
(1) 1/8” (3.5 mm) MIDI output (1/8”-to-5-pin adapter included)
(1) USB Type-B port
(1) power adapter input
Power
via power adapter: 6 VDC, 3 A, center-positive, included
Dimensions
16.2” x 8.6” x 1.9”
(width x depth x height)
41.1 x 21.8 x 4.8 cm
Weight
4.6 lb.
2.1 kg
325
Trademarks & Licenses
Akai Professional and MPC are trademarks of inMusic Brands, Inc., registered in the U.S. and other countries.
Ableton is a trademark of Ableton AG.
ASIO and VST are trademarks of Steinberg Media Technologies GmbH.
The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such
marks by Akai Professional is under license.
MPC software incorporates élastique Pro V3 by zplane.development.
Apple and macOS are trademarks of Apple Inc., registered in the U.S. and other countries.
SD and SDHC are registered trademarks of SD-3C, LLC.
Windows is a registered trademark of Microsoft Corporation in the United States and other countries.
Pro Tools is a trademark of Avid Technology, Inc. in the U.S. and other countries.
All other product names, company names, trademarks, or trade names are those of their respective owners.
For complete legal information, visit akaipro.com/product-legal
326
Addenda
Updates in MPC 2.1
New Features
Exporting Expansions
You can export MPC Expansion Packs (installed on your computer) to your MPC X or MPC Live for use in its
Standalone Mode. (This has been added to Operation > Modes > Browser > Browse.)
To export MPC Expansions:
1. Connect your MPC X or MPC Live to your computer. Make sure both are powered on.
2. On your computer, open the MPC software.
3. On your MPC X or MPC Live, enter Controller Mode.
4. In the MPC software window, click the menu icon (≡), select File > Export, and then click Expansion….
5. In the Export Expansion to Standalone MPC window that appears, click the Drive menu and select a storage
device that you will use with your MPC X or MPC Live: the internal SATA drive (if you have installed one in your
MPC X or MPC Live), an SD card, or a USB flash drive.
6. In the Expansions list, click the box next to each one to select or deselect it. Only the selected ones will be
exported. Click Select all to select all of them or Select none to deselect all of them.
7. Click Export to start exporting, or click Cancel to close the window and not export anything.
The exporting process creates an Expansions folder at the root level of your storage device and copies your
MPC Expansions into it.
To use your expansions, restart your MPC X or MPC Live in Standalone Mode, enter the Browser, and tap
Expansion.
327
Snap: Absolute & Relative
While editing a MIDI or audio track, you can now use
the Grid View or Audio Edit Mode to move or copy
events using two different ways of “snapping” note
events to the grid: Absolute or Relative. (This has
been added to Operation > Modes > Grid View and
Audio Edit Mode.)
To view the Settings, tap the gear icon.
Use the Snap Mode selector to set how events “snap”
to the grid.
Absolute: Events will “snap” to the nearest time
division on the grid (as determined by the TC
field or Time Correct window). This is the
typical and traditional method of using the
snap/quantization feature.
Relative: Events will “snap” to the nearest time
division on the grid (as determined by the TC
field or Time Correct window) plus the original
time position of the event (e.g., an event that is
originally three ticks past a time division on the
grid will snap only to positions that are three
ticks past every time division).
List Edit Settings: Auto-Advance
The Settings window now has some additional lets
you configure certain List Edit Mode settings. (This has
been added to Operation > Modes > List Edit Mode.)
To view the Settings, tap the gear icon.
Use the Auto-Advance on Step Record selector to
turn the feature on or off.
When set to On, pressing a pad when the track is
record-armed will move the audio playhead forward
by a length determined by the current Time Division
setting in the TC/Timing Correct window.
When set to Off, pressing a pad when the track is
record-armed will not change the audio playhead
position.
328
Pitch Quantization
In a MIDI track, you can now force the pitches of note events into a specific scale. This quantization process is available
with other track editing processes. (This has been added to Operation > Modes > Main Mode > Track Section.)
To edit the track, tap the pencil icon on the right edge of the section. The Track Edit window will open.
To open the Pitch Quantize window, tap Pitch Quantize.
To select the desired root note of the scale, use the Root Note field.
To select a type of scale, use the Scale field.
To determine which note events will be quantized, tap the Only apply to selected events checkbox.
When on, only the currently selected note events will be quantized.
When off, all pitches in the current track will be quantized.
To set lowest-possible and highest-possible pitches where the quantized note events will be placed,
use the Start Note and End Note fields (respectively). If a note event is originally outside of this range, it
will be forced to the nearest pitch (within the scale) inside the range.
To continue and quantize the note events, tap Do It.
To cancel, tap Close.
329
Step Sequencer: Velocity Adjustment via Q-Links
While using the Step Sequencer, you can now use the Q-Link knobs to adjust the velocity of the note event at each
step (the Q-Link knobs must be in the Screen edit mode). On MPC X, the number of each step will be shown under
the corresponding Q-Link knob. (This has been added to Operation > Modes > Step Sequencer).
To adjust the velocity of each note event, use the corresponding Q-Link knob to select a value (1–127).
To enter a note event at a step, use the corresponding Q-Link knob to change its velocity from 0 (Off) to a
value of 1 or greater.
To delete a note event from a step, set the corresponding Q-Link knob to its minimum position, 0 (Off).
Pad Perform Mode: User Progressions
You can now use your own progressions (created in the desktop version of the MPC software) on your MPC X or
MPC Live.
To transfer progressions to your MPC X or MPC Live:
1. Connect the storage device that you will use with your MPC X or MPC Live (e.g., the internal drive, an SD card, a
USB drive) to your computer.
2. On your computer, access the storage device and create a folder named Progressions on its root level.
3. Copy your progression files (.progression) from your computer to that Progressions folder.
By default, progressions are saved here:
Windows: C:\Program Files\Akai Pro\MPC\Progressions and/or C:\ProgramData\Akai\MPC\Progressions
macOS: ~/Library/Application Support/Akai/MPC/Progressions
4. Eject and disconnect the storage device from your computer, and connect it to your MPC X or MPC Live.
To use your progressions, start your MPC X or MPC Live in Standalone Mode, enter Pad Perform Mode, and tap
Progressions. Your MPC X or MPC Live will scan the Progressions folder you created and add them to the list of
available progressions.
Faster Attack for Amp Envelopes
In the amp envelope of a drum program or keygroup program, an attack value of 0 now produces a much faster
response, thus making your drum hits even punchier than before. (You can set the attack value in Program Edit Mode.
See Operation > Modes > Program Edit Mode > Drum Programs > Filter/Envelope and Keygroup Programs >
Filter/Envelope to learn more.)
Important: Any drum or keygroup programs that you created and saved before this update will load in MPC 2.1 with
an attack value of 1 to ensure backwards compatibility.
330
Updates in MPC 2.2
New Features
MIDI Control Mode: MIDI Learn
You can now use the MIDI Learn function to assign external MIDI controllers to various parameters in your specific
MPC project:
•
Mixer parameters such as volume, pan, mute, and solo for MIDI or audio tracks, programs, returns, submixes,
and master outputs
•
Pad parameters (for drum programs and clip programs only) such as tuning, filter and amp envelopes, layer
settings, LFO settings, and velocity
•
Program parameters, which depend on the program type
•
Insert effects parameters, which depend on the effect type
These assignments will be saved with your MPC project.
Tip: Because these MIDI assignments are saved within a project, you can use them while working with a project on
both the desktop version of the MPC software or on your MPC hardware in Standalone Mode. You can also include
them with a user template.
To display the MIDI Learn window, press
Menu, tap MIDI Control to enter MIDI Control
Mode, and then tap the MIDI Learn tab.
Each assignment has the following settings:
Source: This is the name or number of the
track, program, return, submix, or master
output.
Target: This is the name of the assigned
command or parameter.
Type: This is the type of message:
•
Toggle Button: When the control is a
button, pressing it will activate or
deactivate its command or parameter.
It will remain in that state until you
press it again.
•
Momentary Button: When the control is a button, pressing and holding it down will activate its command
or parameter. Releasing the button will deactivate it.
•
Fixed Button: When the control is a button, pressing it will send its command.
•
Note: When the control is a button, pressing it will send the MIDI note (determined by the Data field).
•
Abs CC: When the control is a knob, turning it will send its CC message (determined by the Data field)
according to the precise physical position of the knob. (When you start turning it, the value may “jump”
from its current value to the one corresponding to the knob’s position.) This is for use with knobs that
have a maximum and minimum position.
•
Rel CC Offset: When the control is a knob, turning it will send the CC message (determined by the Data
field), starting from the current value. This is for use with 360° knobs controlling parameters that have a
maximum and minimum position.
•
Rel CC 2’s Complement: When the control is a knob, turning it will send the CC message (determined
by the Data field), starting from the current value. This is for use with 360° knobs controlling bipolar
parameters where there is a center (12:00) position (e.g., panning).
This is automatically detected based on the Source and Target fields, though you can use this field to assign it
manually if it does not detect it properly.
331
Ch: This is the MIDI channel the control is using.
Data: This is the MIDI note number or CC number.
Flip: Tap this box to select or deselect it. When selected, the control’s polarity will be reversed (e.g., a button’s
“off” state will become its “on” state and vice versa).
To assign a parameter to a hardware control:
1. Tap Learn in the upper-left corner so it is on. (The Enable Mapping button will also activate if it is not already on.)
2. Tap + in the lower-left corner to create an “empty” assignment (its Target menus will be set to None and Off).
Alternatively, tap an assignment that is already in the list if you want to change it.
3. Move or press the desired control on your MIDI controller. The Type, Ch, and Data fields will be automatically
assigned.
4. Use the Source field to select a MIDI or audio track, program, return, submix, or master output (for drum programs
and clip programs, you can select the entire program or a single pad within it). The Target menu will indicate the
source you selected.
5. Use the Target menu to select the parameter. Your selection will be shown under Target in the list, as well.
The control on your MIDI controller will now control the Target parameter.
To assign more controls, repeat Steps 2–5.
To stop assigning controls, tap Learn again so it turns off.
To clear an assignment, follow the steps above to reassign its Source field to None and assign its Target field to Off.
To delete an assignment (the entire slot), tap it in the list, and then tap the trash-can icon in the lower-right corner.
To delete all assignments, press and hold Shift, and then tap the trash-can icon in the lower-right corner. In the
window that appears, tap Remove All to continue or tap Cancel to not delete any assignments.
Humanize
You can now apply randomization to the timing, length, and/or velocity of MIDI events. This process is available with
other track editing processes. (This has been added to Operation > Modes > Main Mode > Track Section).
To edit the track, tap the pencil icon on the right edge of the section. The Track Edit window will open.
To open the Humanize window, tap Humanize.
332
The Humanize function applies randomization to the timing, length, and/or velocity of MIDI note events.
To select whether or not humanization will be applied to the timing of MIDI events, tap the Humanize Time
checkbox.
To select the maximum number of pulses by which the timing of an event will be adjusted, use the Amount
(Pulses) slider.
To set how dramatically the humanization effect is applied to the timing, use the Eagerness slider. Negative
values correspond to playing “ahead of the beat” while positive values correspond to playing “behind the beat.”
To set whether or not humanization will be applied to the duration of MIDI note events, tap the Humanize
Note Length checkbox.
To set how dramatically the humanization effect is applied to note lengths, use the Length (%) slider.
To set whether or not humanization will be applied to the velocities of MIDI note events, tap the Humanize
Velocity checkbox.
To set how dramatically the humanization effect is applied to note velocities, use the Strength (%) slider.
To determine which notes will use these humanization values, tap the Only Apply to Selected Events checkbox.
When on, just the currently selected notes will be humanized.
When off, all notes in the track will be humanized.
To apply humanization and keep this window open, tap Apply.
To apply humanization and close the window, tap Do It.
To close the window without making any changes, tap Close.
333
Generate Random Events
You now create random melodic or drum patterns on the current MIDI track. This process is available with other
track editing processes. (This has been added to Operation > Modes > Main Mode > Track Section).
To edit the track, tap the pencil icon on the right edge of the section. The Track Edit window will open.
To open the Generate Random Events window, tap Generate Random Events.
The Generate Random Events function creates random melodic or drum patterns on the current MIDI track.
To select the type of events you want to create, use the Event Type field to select Drum Events or Melodic
Events.
To select how the events will be created relative to the existing events on the track, use the Replace field:
Replace All Events: Select this option to replace all events on the track with the randomly generated ones.
Replace Events in Note Range: Select this option to replace all events in the designated note range on the
track with the randomly generated ones. Use the Bank or Start Pad and End Pad menus to set the note
range for drum events or the Start Note and End Note menus to set the note range for melodic events.
Add to Existing Events: Select this option to add the randomly generated events to the track without
replacing or overwriting the existing ones.
To set how many bars the events will use, use the Pattern Size (Bars) field. The highest possible value is the
number of bars in the current sequence.
To select the duration of the events, use the Note Length field. (This feature is nonfunctional if Legato is
enabled while generating melodic events.)
To generate the events and keep this window open, tap Apply.
To generate the events and close the window, tap Do It.
To close the window without generating any events, tap Close.
334
If Event Type is set to Drum Events:
To select the pad bank that will be used to generate the events, use the Bank field or select Range to
use the Start Pad and End Pad menus to define a specific pad range instead.
To define a specific pad range over which the events will be generated, use the Start Pad or End Pad
fields. You can use these fields only if the Bank menu is set to Range.
To set how closely together the events will be placed in the track, use the Density (%) slider.
To set how widely or narrowly the rhythmic patterns of the generated notes vary, use the Rhythm
Variation slider.
If Event Type is set to Melodic Events:
To define a specific note range over which the events will be generated, use the Start Note or End Note
fields.
To enable or disable legato, tap the Legato checkbox.
Without legato applied.
With legato applied.
When on, the generated notes will be extended or shortened to create a long, unbroken phrase from the
first note event’s start point to the last note event’s end point. Each note event will sustain until another
note event starts. If multiple note events start at the same time (and are not the last note events), their
lengths will become identical.
When off, the generated notes will use the duration set by the Note Length menu.
335
To set the maximum number of note events that can be sounding simultaneously in the track, use the
Polyphony field to select 1–8.
To determine whether or not the notes will use a scale, tap the Constrain Notes to Scale checkbox.
When on, the notes will be within the scale determined by the Scale menu.
When off, the notes will be chromatic.
To set how closely together the events will be placed in the track, use the Density (%) slider.
To set the root note of the scale that the notes will use, use the Root Note field.
To select the scale or mode that the generated notes will use, use the Scale field.
Project Template
You can now select a project file to use as a template for new projects. (This has been added to Operation > General
Features > Menu > Save and Menu > Preferences > Project Load/Save.)
To select a project template file, do either of the following:
1. Tap the icon in the upper-left corner to enter the Menu.
2. Tap the gear icon to enter the Preferences.
3. Tap Project Load/Save.
4. Tap the magnifying-glass icon next to the Template File field to select the project you want to use as a
template.
1. In Main Mode, tap the Project field in the upper-left corner.
2. Tap Save As… at the bottom of the screen.
3. Tap the Save as Template checkbox to check it.
4. Name and select a location for the project, as usual.
5. Tap Save. (The file will now be shown in the Template File field in the Preferences’ Project Load/Save tab.)
To load the project template from the startup screen (when you power on your MPC hardware), tap User
Template at the bottom of the screen. In order for this option to be available, New Project Dialog (in the
Project Defaults tab) in the Preferences must be set to Demo or Demo/Template/Recent.
336
Updates in MPC 2.3
New Features
Arpeggiator
MPC now includes a full-featured arpeggiator and phrase player for melodic program types.
To open the Arpeggiator settings:
1. Set the current track type to Plugin, Keygroup, MIDI, or CV.
2. Open the Arpeggiator window by doing either of the following:
• Press and hold the Note Repeat button, then tap Arp at the bottom-right of the screen.
• Alternatively, press the Arpeggiator F-Key (MPC X).
To activate the Arpeggiator, tap Enable so it is checked.
Tap again to Disable the Arpeggiator.
To latch the Arpeggiator, tap Latch so it is checked. Tap
again to Disable Latch.
The Setup section of the Arpeggiator window sets what
kind of arpeggiator will be used and its functions:
Use the Action field to set the type: Arp, Note
Repeat, Rhythm and Pattern. See below for more
details about these types and their additional
parameters.
Use the Step Size field to set the note value of each
arpeggiator step from 1/1–1/64 beats, including T
(triplet) variations. This field is not used in Pattern
mode.
Use the Note Length slider to set the length of the
played note in each step, from 1–100%.
Use the Velocity field to set the velocity of the
arpeggiator notes. Choose As played, From first
note, Accented, Full, 3/4, Half or 1/4.
Use the Swing field to set the amount of swing in the
arpeggiator from 50% to 75%. Swing lets you
"shuffle" your beats—from subtle to extreme.
The Arp mode section of the Arpeggiator window is
available when the Action is set to Arp. When this action
is selected, hold down a chord and the arpeggiator will
play a pattern based on the notes held.
Use the Pattern field to set how the arpeggiator
triggers the held notes.
Use the Octaves field to set how many octaves of the
held notes the arpeggiator will cycle through.
Use the Variation field to apply rhythmic variation to
the set pattern.
337
The Rhythm section of the Arpeggiator window is
available when Action is set to Note Repeat or Rhythm.
The Note Repeat action provides traditional MPC Note
Repeat behavior. When the Rhythm arpeggiator action is
selected, hold down a chord and the arpeggiator will play
the held notes in a rhythmic pattern.
Use the Spread field to spread the timing of the held
notes, creating a glissando effect.
Use the Rhythm Pattern field to choose the pattern
played when notes are held. This is only available for
the Rhythm action.
The Pattern section of the Arpeggiator window is
available when the Action is set to Pattern. When this
arpeggiator action is selected, hold down a single note to
trigger a melodic phrase. As you change what note is
held, the melodic phrase will be transposed.
Use the Pattern field to choose the pattern.
The Settings section of the Arpeggiator window offers
additional options to control the arpeggiator.
If you have a sustain pedal connected, you can enable
Sustain Pedal Latches to use it to control latching.
Use the Latch Mode setting to set the latch behavior.
When set to Reset, adding a new note(s) will reset the
currently latched note(s). When set to Add, new notes
will be added to currently latched notes.
Tap Close to close the Arpeggiator window.
338
Auto Sampler
You can now capture and convert any plugin preset or external instrument preset into a Keygroup sampler patch.
To open the Auto Sampler:
1. Open the Sampler mode by doing either of the following:
• Press Menu and then tap Sampler.
• Press Sampler (MPC X).
2. Press the Auto Sampler icon in the toolbar.
Sample Source Information
The Track name and Program name fields show the
target track and program that will be sampled. This
will be automatically selected as the active track and
program when Auto Sampler is opened.
Use the Record from field to select an external or
resample input to record from:
To capture the output of a plugin, simply select
a Plugin track before opening Auto Sampler.
Note: When a plugin track is selected, the Auto
Sampler will only sample the plugin track,
regardless of the setting in the Record From
field.
To capture a preset from an external
instrument such as a sound module, select the
Input that the external instrument is connected to.
Note Range
Use the Min note and Max note settings to determine
the lowest and highest notes used to create the
sampler patch.
Use the Note stride to determine the range of notes
that each sample will cover. For instance, a note
stride of 5 means that every 5 notes will utilize a
different sample.
Check the Extend min/max notes box to sample all
the way to the lowest and highest notes, regardless of
the Min Note and Max Note settings.
Velocity
Tap the boxes next to Layers 1–4 to select how many
layers will be used to create the sampler patch.
Use the Velocity value sliders to set the velocity of
each layer.
339
Sampling
Use the Note length slider to set the length of the
sampled note in seconds.
Use Tail slider to set the length of the Audio Tail in
seconds. This will add extra seconds to the end of the
resulting audio file. This is useful if you are capturing
samples whose sounds exceed the defined audio
length (e.g., long reverb or delay, one-shot samples
with long decays, etc.). We recommend using an
audio tail of at least a couple of seconds.
Use Base name to set the naming convention for the
samples that will be created by the Auto Sampler.
Looping
Use the Enable looping field to select how the
resulting samples can or cannot be looped:
•
Off: The sample will not loop.
•
Forward: You can hold down the pad to
cause that sample to repeat from the Loop
Position to the end of the sample. Release
the pad to stop the repeating playback.
•
Reverse: You can hold down the pad to
cause that sample to play in reverse,
repeating from the end of the sample to the
Loop Position. Release the pad to stop the
repeating playback.
•
Alternating: You can hold down the pad to
cause that sample to play from the Loop
Position to the end of the sample and then
play in reverse until it reaches the Loop
Position again. This will repeat as long as you
are holding the pad down. Release the pad to
stop the repeating playback.
Use the Loop start and Loop end sliders to set the starting and ending points in the sample where the loop will
occur.
Use the Crossfade field to set the amount of crossfade between the loop end and loop start in seconds.
Use the Crossfade Type field to select Equal Power or Linear crossfade.
Under On completion, check Make current program to
load the completed sampler patch as the current
program.
Under Info, the Session Duration field provides an
estimate of how long the auto sampling process will take.
Tap OK to initiate the auto sampling process. A Progress
window will appear. Click Cancel to stop the auto
sampling process. Any samples already created will be
retained.
Tap Cancel to close the Auto Sampler window without
continuing.
340
Crossfade Looping
You can now add real time crossfade looping to sample playback.
To apply crossfade looping to a sample:
1. Open Sample Edit mode by doing either of the following:
• Press Menu, and then tap Sample Edit.
• Press Sample Edit (MPC X).
2. Make sure the loop Lock setting is set to Off.
3. Tap the Loop button to select the Forward (FWD) loop mode.
4. Make sure there is at least 10 samples of space between the Start point and Loop point.
5. Tap the X-Fade button to open the X-Fade window:
To set the length of the crossfade in samples, use the Length field.
To set the type of crossfade, use the Type field. Select Equal Power or Linear.
To close the window and return to Trim Mode, tap the X or tap Close.
When you are finished, press Pad A16 – Play Continuous Loop in Sample Edit Trim Mode to hear the crossfade
applied to the sample.
341
Mode Selection Shortcut
You can now press and hold the Menu button on your MPC X, MPC Live or MPC Touch and press a pad to select a
menu mode. The pads follow the 4x4 layout of the Mode Menu.
Pad Perform Mode: Chromatic Type
You can now use Pad Perform Mode to set the pads to follow a chromatic layout. When the Chromatic type is
selected, each pad is assigned a note, ascending by one semitone with each pad. Pads with notes in the key
determined by the Scale will be lit, while pads with notes between the scale degrees will be unlit.
Q-Link Navigation Enhancements
Q-Link functionality has been enhanced in the following modes: Main Mode, Track View, Next Sequence, Grid Editor,
and Audio Edit Mode.
Set the Q-Link Mode to Screen in these pages to access the following controls:
Use Q-Link Knob 2 to adjust the playhead position.
Use Q-Link Knob 3 to scroll through the waveform in the large waveform display.
Use Q-Link Knob 4 to zoom in or zoom out at the playhead position.
Note: For MPC Live and MPC X in standalone mode, the Zoom and Scroll Q-Links are only available in the Grid
Editor and Audio Edit Mode.
342
Split Events
You can now easily split note events, useful for creating intricate hi-hat parts or quintuplet/sextuplet motifs or drum
beats. (This has been added to Operation > Modes > Main Mode > Track Section.)
To edit the track, tap the pencil icon on the right edge of the Main Mode screen. The Track Edit window wlll
open.
To open the Split Events window, tap Split Events.
To set how many events notes will be divided into, use the Into slider.
To determine which notes will be divided, tap the Only selected events checkbox.
To split the events and close the window, tap Do It.
To close the window without making any changes, tap Close.
343
AIR Instrument Plugins
MPC now includes three new plugin instruments: AIR TubeSynth, AIR Bassline, and AIR Electric.
AIR Bassline
The AIR Bassline plugin emulates the sound of classic
mono synths, with a contemporary twist. Bassline also
comes packaged with four integrated AIR effects (Chorus,
Delay, Compressor and Hype), as well as two built-in
distortion algorithms (Overdrive and Clip).
Osc/Filter/Envelope
Use this tab to adjust the settings for the oscillators,
as well as their filter and envelope settings.
Parameter
Oscillator
Filter
Envelope
Waveform
Description
Value Range
Continuously variable waveshape for the oscillator.
Saw Octave, Saw,
Square, Sine
Sub-Octave Amount of sub-octave oscillator.
0–100%
Fifth
Amount of fifth-oscillator.
0–100%
Start Phase
Position of the waveform when a note is triggered.
Free, 0 degr., 180
degr.
Glide Time
Amount of time to slide from the pitch of one note to the next
note played.
10.0 ms – 2.00 s
Boost
Boosts the signal of the oscillator.
0.0 – 48.0 dB
Boost Freq.
Center frequency of the boost.
* 1.0 – * 240.0
Boost
Envelope
Amount of effect of the envelope on the Boost section.
Gain 0–100%, Off,
Frequency 0–100%
Adjust Gain to control the amount of boost.
Adjust Frequency to control the center frequency of the boost.
LP Cutoff
Cutoff frequency for the low-pass filter.
20.0 Hz – 20.0 kHz
Reso
Resonance of the filter.
0–100%
Filter Env
Envelope of the filter.
At negative values, decreases the cutoff value based on the
decay value.
At positive values, increases the cutoff value based on the
decay value.
-100% – 0 – +100%
HP Cutoff
Cutoff frequency for the high-pass filter.
10.0 – 500 Hz
Amp Attack
Length of time for the note to reach full volume.
0–100 Soft,
0–100% Hard
Amp Decay
Length of time for the note to reach the sustained volume.
0–100%
Filter Decay Length of time for the filter to reset after being released.
0–100%
Pitch Mod
0–100%
Amount of pitch modulation applied to the envelope.
344
Velocity/Master/Chorus
Use this tab to adjust the Velocity Control settings, Master volume. You can also apply and adjust the settings
for the built-in Chorus effect.
Parameter
Velocity
Master
Chorus
Description
Value Range
Amp Control
The amount of effect velocity has on amplitude
control.
0–100%
Filter Control
The amount of effect velocity has on filter control.
0–100%
Boost Control
The amount of effect velocity has on boost control.
0–100%
Env Retrigger
Sets whether the envelope will retrigger when a note is Off, On
played while another note is being held.
Master Volume
Sets the volume level.
-Inf dB – +6.0 dB
Drive Type
Choose one of two drive algorithms.
Overdrive, Clip
Drive Amount
Amount of drive applied.
0–100%
Bend Range
Number of semitones up or down controlled by MIDI
pitch bend messages.
0–12
Rate
Modulation speed of the chorus effect.
20.0 Hz – 20.0 kHz
Depth
Modulation depth of the chorus effect.
0–100%
Mix
Wet/dry amount of the chorus effect.
-100% – 0 – 100%
On/Off
Enables or disables the effect.
Off, On
Delay
Use this tab to apply and adjust the settings for the built-in delay effect.
Parameter
Description
Time
Length of time of the delayed signal.
Value Range
When Sync is set to Free: 1 ms – 2.00 s
When Sync is set to Sync: 1/32 – 8/4
Sync
Sync the Delay Time to the Global Tempo or set to Free to adjust Time
by milliseconds.
Free, Sync
Mix
Wet/dry amount of the delay effect.
0–100%
Feedback
Amount of signal fed back into the delay line.
0–100%
Damp
Center frequency of where the delay signal will be dampened.
1.00 – 20.0 kHz
Reso
Amount of resonance of the feedback signal.
0–100%
Reso Freq
Center frequency for feedback resonance.
100 Hz – 10.0 kHz
Ratio
Reduces the delay Time in either the Left or Right stereo field. This is
useful for creating offset, panned delays.
L 50:100, R 50:100
HPF
Center frequency for delay signal high-pass filter.
20.0 Hz – 1.0 kHz
Width
Stereo width of delay signal. Higher values give wider stereo separation.
0–100%
On/Off
Enables or disables the effect.
Off, On
345
Compressor/Hype
Use this tab to apply and adjust the settings for the built-in Compressor and Hype effects.
Parameter
Compressor
Hype
Description
Value Range
Threshold
Signal level after which the compressor will be applied.
0.0 – -60. dB
Ratio
Amount of compression applied.
1.0:1 – 100.0:1
Output
Amount of additional output gain for the compressed
signal.
0.0 – 30.0 dB
Mix
Wet/dry mix of the compressor effect.
0–100%
Knee
How gradually the compressor reacts as the threshold
is reached.
Lower values apply a "soft" knee (compression is
applied more slowly as signal approaches the
threshold), and higher values apply a "hard" knee
(compression is immediately applied when the
threshold is reached).
0–100%
Attack
Length of time to apply the compression.
100 us – 300 ms
Release
Length of time for compressed signal to return to
original level.
10 ms – 4.00 s
On/Off
Enables or disables the effect.
Off, On
High
Dampens or maximizes high end frequencies.
-100 – 0 – +100%
Low
Dampens or maximizes low end frequencies.
-100 – 0 – +100%
On/Off
Enables or disables the effect.
Off, On
346
AIR Electric
The AIR Electric plugin emulates the sound of classic
electric pianos. Dedicated Pickup, Envelope, Bell and
Noise parameter sections provide a huge amount of
flexibility to configure the timbre of the electric piano
sound. Electric also includes five AIR effects: Tremolo,
Tube Distortion, Chorus, Delay and Spring Reverb.
While viewing any of the tabs listed below, you can
quickly enable or disable the Bell and Noise sounds, as
well as the built-in effects (Tremolo, Tube, Chorus, Delay
and Spring Reverb).
When viewing a specific tab, you can enable or disable
the sound or effect by pressing the circle in the upperright corner of each section.
Pickup/Env
Use this tab to edit the settings for the emulated pickup and the sound envelope.
Description
Value Range
Type
Type of pickup emulated.
Pickup, 0–100%
Electro-Static,
0–100% ElectroMagnetic
Height
Height of the pickup to the tines.
0.0 – 5.0 mm
Distance
Distance of the pickup to the tines.
0.1 – 10.0 mm
Clip
Amount of clipping applied to the signal.
0–100%
Keytrack
Ties the pickup parameters to the pitch being played. 0–100%
At higher values, the Distance is increased as the
pitch is increased.
Attack
Length of time for the note to reach full volume.
100–0% Hard,
0–100% Soft
Decay
Length of time for the note to reach the sustained
volume.
100 ms – 20.0 s
Release
Length of time for the note to become silent after
being released.
100 ms – 5.0 s
Peak Length
Length of time full volume is held before decaying.
3–50 ms
Keytrack
Ties the envelope parameters to the pitch being
played.
At higher values, the envelope time is decreased as
the pitch is increased.
0–100%
Parameter
Pickup
Envelope
347
Bell/Noise
Use this tab to apply and adjust the settings for the Bell and Noise sounds.
Parameter
Bell
Noise
Description
Value Range
Tune
Pitch of the bell sound, in semitones above the root
pitch.
0– 60 semitones
Dry/PU
Mix of Dry versus Pickup signal for the bell sound.
-100% – 0% – +100%
Volume
Level of the bell sound.
-Inf dB – 0.0 – +6.0 dB
Tune Keytrack
Ties the tuning of the bell sound to the pitch being
played.
0–100%
Decay
How long it takes for the bell sound to dissipate.
100 ms – 7.0 s
Keytrack
Ties the amount of bell sound to the pitch being
played.
At negative values, the bell sound is increased as the
pitch increases.
At positive values, the bell sound is increased as the
pitch decreases.
-100% – 0% – +100%
Freq
Center frequency of the noise effect.
200 Hz – 16.0 kHz
Random
Amount of randomization applied to the noise effect.
0–100%
Mix
Level of noise effect present.
-Inf dB – 0.0 – +6.0 dB
Attack
Length of time for the noise effect to reach full level.
1–50 ms
Decay
Length of time for the noise effect to dissipate.
100 ms – 3.00 s
Keytrack
Ties the Freq to the pitch being played.
0–100%
Setup
Use this tab to adjust general settings for the plugin.
Parameter
Description
Value Range
Polyphony
Number of voices available.
1–16 Voices
Master Volume
Overall level of the plugin.
-Inf dB – 0.0 – +6.0 dB
Velo Level
Adjusts how much incoming velocity is applied.
0–100%
Velo Tone
Ties the incoming velocity to tone.
At higher values, increased velocity increases tone brightness.
0–100%
Velo Attack
Ties the incoming velocity to the attack envelope.
At higher values, lower velocities feature longer attack times.
0–100%
348
Trem/Tube/Chorus
Use this tab to apply and adjust the settings for the built-in Tremolo, Tube (Overdrive), and Chorus effects.
Parameter
Tremolo
Description
Rate
Value Range
Modulation speed of the effect.
When Sync is set to Free: 0.25 – 13.00 Hz
When Sync is set to Sync: 8/4 – 1/16
Tube
Chorus
Sync
Sync the Tremolo Rate to the Global Tempo or let it
run Free.
Free, Sync
Mode
Select Pan for stereo field modulation, or Tremolo for
amplitude modulation.
Pan, Tremolo
Depth
Amount of modulation applied.
0–100%
Drive
Amount of drive applied.
0–100%
Headroom
Amount of gain reduction between the clean signal
and the driven signal.
-30.0 – 0.0 dB
Saturation
Amount of saturation applied.
0–100%
Output
Output level of the tube driven signal.
-20.0 – 0.0 – +20.0 dB
Rate
Modulation speed of the effect.
0.40 – 3.20 Hz
Depth
Amount of pitch modulation of the effect.
0–100%
Mix
Wet/dry amount of the chorus effect.
0–100%
Delay
Use this tab to apply and adjust the settings for the built-in Delay effect.
Value Range
Parameter
Description
Time
Amount of time between the dry signal and the delayed signal.
When Sync is set to Free: 1 ms – 2.00 s
When Sync is set to Sync: 1/32 – 8/4
Sync
Sync the Delay Time to the Global Tempo or set to Free to adjust Time
by milliseconds.
Free, Sync
Mix
Wet/dry amount of the delay effect.
0–100%
Feedback
Amount of signal fed back into the delay line.
0–100%
Damp
Center frequency of where the delay signal will be dampened.
1.00–20.0 kHz
Reso
Amount of resonance of the feedback signal.
0–100%
Reso Freq
Center frequency for feedback resonance.
100 Hz – 10.0 kHz
Ratio
Reduces the delay Time in either the Left or Right stereo field. This is
useful for creating offset, panned delays.
L 50:100, R 50:100
HPF
Center frequency for delay signal high-pass filter.
20.0 Hz – 1.0 kHz
Width
Stereo width of delay signal. Higher values give wider stereo separation.
0–100%
349
Spring Reverb
Use this tab to apply and adjust the settings for the built-in Spring Reverb effect.
Parameter
Description
Value Range
Pre-Delay
Length of time between dry signal and reverberated signal.
0–250 ms
Time
Length of reverb tail.
1.0 – 10.0 s
Mix
Wet/dry amount of the reverb effect.
0–100%
Diffusion
Rate of increasing density of reverb reflections.
At lower settings, the sound of individual reflections is more present.
At higher settings, reflections are more uniform.
0–100%
Width
Stereo width of reverb signal. Higher values give wider stereo separation.
0–100%
Low Cut
Center frequency for reverb signal low-cut filter.
20.0 Hz – 1.00 kHz
350
AIR TubeSynth
The AIR TubeSynth plugin emulates the sound of classic
vintage analog polysynths. TubeSynth is based on the
highly acclaimed AIR Vacuum Pro desktop synth plugin
and also includes 5 integrated AIR effects.
Oscillator
Use this tab to adjust the settings for the two variable
Oscillators and the Sub Oscillator.
Description
Value Range
Octave
Coarse tuning of the oscillator by octaves.
The Wide setting provides additional Fine
tuning controls.
Wide, 32', 16', 8', 4', 2'
Fine
Fine tuning of the oscillator by semitones.
Parameter
Oscillator 1
When Octave is set to Wide: -70.00 – 0.00 – +70.00
When Octave is set to 32'–2': -12.00 – 0.00 – +12.00
Oscillator 2
Shape
Waveshape of Oscillator 1 (continuously
variable).
Triangle, Saw, Square, Pulse
F-EnvShape
Amount of Filter Envelope output subtracted
from or added to the value defined by the
Osc 1 Shape parameter.
-100 – 0 – +100%
Quad
Enables or disables four-voice emulation for
the oscillator.
Off, On
Detune
Adjusts tuning of the additional Quad voices.
0–100%
Octave
Coarse tuning of the oscillator by octaves all
the way down to LFO speed.
LFO, 32', 16', 8', 4', 2'
Fine
Fine tuning of the oscillator.
When Octave is set to LFO: 0.01 – 20.00 Hz
When Octave is set to 32'–2': -12.00 – 0.00 – +12.00
semitones
Shape
Waveshape of Oscillator 2 (continuously
variable).
Noise, Saw, Square, Pulse
F-EnvShape
Amount of Filter Envelope output subtracted
from or added to the value defined by the
Osc 2 Shape parameter.
-100 – 0 – +100%
Sync
Enables or disables syncing of Oscillator 2 to
Oscillator 1.
Off, On
Micro Detune
Additional detuning of Oscillator 2.
0–100%
Phase
Position of the waveshape when the sound is 0–360 degrees
triggered.
Sub Oscillator Shape
Waveshape of the sub oscillator (continuously Triangle, Saw, Square, Pulse
variable).
351
Mixer / Filter
Use this tab to control EQ for Oscillator 2, set the levels of the oscillators and effects, and edit the low-pass filter.
Parameter
Osc 2 EQ
Mixer
LP Filter
Description
Value Range
Gain
Amount of gain applied to the selected Frequency.
-48 – 0 – +48 dB
Frequency
Center frequency for the equalization band.
25–10,000 Hz
Drive
Amount of drive added to the EQ signal.
0–100%
Keytrack
Ties the EQ settings to the pitch being played
0–100%
Osc 1
Level of Oscillator 1.
0–100%
Osc 2
Level of Oscillator 2.
0–100%
Sub Osc
Level of the Sub Oscillator.
0–100%
Ring Mod
Level of Ring Modulation effect.
0–100%
Drive
Level of Drive effect.
0–100%
Cutoff
Center frequency of the low-pass filter cutoff.
0–100%
Reso
Amount of resonance of the low-pass filter.
0–100%
Slope
Amount of attenuation applied above the cutoff
frequency.
0–24 dB/oct
Saturation
Amount of saturation applied to the low-pass filter.
0–100%
Env
Percentage of the envelope output subtracted from or
added to the LP Filter Cutoff.
-100 – 0 – +100%
Keytrack
Ties the LP Filter Cutoff to the pitch being played.
0–100%
352
Envelope
Use this tab to adjust the various envelope settings.
Parameter
Description
Value Range
Filter Envelope Attack
Length of time for the filter to reach full level.
1.00 ms – 100 s
Decay
Length of time for the filter to reach sustain level.
1.00 ms – 100 s
Sustain
Length of time for the filter to hold sustain level.
0–100%
Release
Length of time for the filter to dissipate when released. 1.00 ms – 100 s
Attack
Length of time for the note to reach full level.
1.00 ms – 100 s
Decay
Length of time for the note to reach sustain level.
1.00 ms – 100 s
Sustain
Length of time for the note to hold sustain level.
0–100%
Release
Length of time for the note to dissipate when released. 1.00 ms – 100 s
Start Level
Initial velocity level of the envelope.
0–100%
Start Time
Length of time for the envelope to start.
0–5000 ms
Slope Hold
Percentage of Envelope subtracted from or added to
the Destination when a note is held.
-100 – 0 – +100%
Slope Rel
Percentage of Envelope subtracted from or added to
the Destination when a note is released.
-100 – 0 – +100%
Destination
Where the envelope will be applied to.
Off, Pitch, Osc 2
Pitch, LFO 1/2 Rate,
Osc1 Quad Det., Osc
1/2 Shape, Osc 1/2
Level, Ring Level
Amp Envelope
Envelope 3
353
LFO
Use this tab to adjust the settings for the low-frequency oscillators.
Parameter
LFO 1/LFO 2
Description
Value Range
Shape
Waveshape of the low-frequency oscillator.
Sine, Square. Saw
Up, Saw Down,
Pump, S&H, Drift
Destination
Where the low-frequency oscillator is sent.
LFO1: Off, Pitch, Filter,
Level, Pan
LFO2: Pitch, Osc 1/2 Shape,
Osc 1/2 Pitch, LPF,
Quad Detune, Osc
EQ Freq, Osc 2 EQ
Gain, Ring Level
Rate
Speed of modulation.
When Sync is Off: 0.01 – 20.00 Hz
When Sync is On: 8/4 – 1/32
Modulation
Depth
Amount of modulation applied.
0–100%
Fade
Apply a fade-in or fade-out of the LFO signal.
0.00 – 20.00 s out,
No fade,
0.00 – 20.00 s in
Sync
Sync the LFO Rate to the Global Tempo or turn Off to Off, On
adjust Rate by Hertz.
Source
Where the modulation signal is sent from.
Filter Env, Amp Env,
Osc 1, Osc 2
Destination
Where the modulated signal is received.
Pitch, Osc 1/2 Shape,
Osc 1/2 Pitch, LPF,
Quad Detune, Osc
EQ Freq, Osc 2 EQ
Gain, Ring Level
Depth
Amount of modulation applied.
0–100%
354
Setup
Use this tab to adjust plugin setup parameters.
Parameter
Description
Value Range
Velocity 1
Send Velocity data to one of the following control
destinations.
Amp, Cutoff, Osc1
Shape, Osc2 Shape,
Osc1&2 Shape
Depth
Amount of modulation applied.
0–100%
Velocity 2
Send Velocity data to one of the following control
destinations.
Amp, Cutoff, Osc1
Shape, Osc2 Shape,
Osc1&2 Shape
Depth
Amount of modulation applied.
0–100%
Modwheel
Send Modwheel data to one of the following
control destinations.
Amp, Cutoff, Osc1
Shape, Osc2 Shape,
Osc1&2 Shape
Depth
Amount of modulation applied.
-100 – 0 – 100%
Aftertouch
Send Aftertouch data to one of the following
control destinations.
LFO 1 Depth, Cutoff,
Osc1 Shape, Osc2
Shape, Osc1&2 Shape
Depth
Amount of modulation applied.
-100 – 0 – 100%
Polyphony
Number of allowable voices, and how voices are
triggered.
Legato, Retrigger, 2, 3, 4
Bend Range
Number of semitones up or down controlled by
MIDI pitch bend messages.
0–12 (semitones)
Glide Time
Amount of time to slide from the pitch of one note
to the next note played.
1.00 ms – 100 s
Glide All
Enables or disables pitch gliding for all triggered
notes, not just legato notes.
Off, On
Detune
Amount of detuning applied. This setting is only
applied when Doubling is enabled.
0–100%
Doubling
Enables or disables voice doubling.
Off, On
Shape
Amount of signal sent to a Tube Drive.
0–100%
Width
Stereo width of the audio signal. Higher values
give wider stereo separation.
0–100%
Level
Overall output volume of the plugin.
-Inf dB – +12.0 dB
Controller Destinations
Setup
Output
355
Chorus
Use this tab to apply and adjust the settings for the built-in Chorus effect.
Parameter
Description
Value Range
Rate
Modulation speed of the effect.
0.01 – 10.0 Hz
Delay
Length of time the wet signal is offset from the dry signal.
0.00 – 24.00 ms
Voices
Number of voices used in the chorus effect.
3, 4, 6
LFO Wave
Waveshape of the low-frequency oscillator for the chorus effect.
Tri, Sine
Depth
Amount of pitch modulation of the effect.
0.00 – 24.00 ms
Width
Stereo width of the chorus effect. Higher values give wider stereo
separation.
0–100%
Lo Cut
Center frequency for the chorus low-cut filter.
20.0 Hz – 1.0 kHz
Mix
Wet/dry amount of the chorus effect.
0–100%
Delay
Use this tab to apply and adjust the settings for the built-in delay effect.
Value Range
Parameter
Description
Time
Length of time between the dry signal and the delayed signal.
When Sync is set to Free: 1 ms – 2.00 s
When Sync is set to Sync: 1/32 – 8/4
Sync
Enable to sync the Delay Time to the Global Tempo, disable to set the
Time in milliseconds.
Off, On
Feedback
Amount of delay signal fed back into the delay line.
0–100%
Mix
Wet/dry amount of the delay effect.
0–100%
Damp
Center frequency of where the delayed signal will be dampened.
1.00 – 20.0 kHz
Reso
Amount of resonance of the feedback signal.
0–100%
Reso Freq
Center frequency for feedback resonance.
100 Hz – 10.0 kHz
Ratio
Reduces the delay Time in either the Left or Right stereo field. This is
useful for creating offset, panned delays.
L 100:50, R 50:100
HPF
Center frequency for delay signal high-pass filter.
20.0 Hz – 1.0 kHz
Width
Stereo width of delay signal. Higher values give wider stereo separation.
0–100%
356
Reverb / Compressor / Hype
Use this tab to apply and adjust the settings for the built-in Reverb, Compressor and Hype effects.
Parameter
Reverb
Compressor
Hype
Description
Value Range
Mode
Type of reverb applied.
Hall, Stadium, Room,
Abstract
Time
Length of reverb tail.
0.4 s – +Inf s
Lo Cut
Center frequency for the reverb low-pass filter.
1 – 1000 Hz
Hi Cut
Center frequency for the reverb high-pass filter.
1.0 – 20.0 kHz
Mix
Wet/dry mix of the reverb effect.
0–100%
Threshold
Signal level after which the compressor will be
applied.
0.0 – -60. dB
Output
Amount of additional output gain for the compressed
signal.
0.0 – +30.0 dB
Mix
Wet/dry mix of the compressor effect.
0–100%
Ratio
Amount of compression applied.
1.0:1 – 100.0:1
Knee
How gradually the compressor reacts as the threshold 0–100%
is reached.
Lower values apply a "soft" knee (compression is
applied more slowly as signal approaches the
threshold), and higher values apply a "hard" knee
(compression is immediately applied when the
threshold is reached).
Attack
Length of time to apply the compression.
100 us – 300 ms
Release
Length of time for compressed signal to return to
original level.
10 ms – 4.00 s
High
Dampens or maximizes high end frequencies.
-100 – 0 – +100%
Low
Dampens or maximizes low end frequencies.
-100 – 0 – +100%
357
Plugin Preset Support
Internal Akai effects now include all new plugin editors and factory presets.
To load a plugin preset:
1. Open a plugin instrument or effects plugin editor.
2. At the top of the instrument or effect editing window will be a dropdown menu for selecting presets. Double-tap
the menu to open it, and tap a preset to select it.
A number of third-party VST plugins will also display a bank of presets when used with MPC.
Additionally, you can now save and load plugin presets.
To save or load a plugin preset:
1. Open a plugin instrument or effects plugin.
2. To the right of the dropdown menu for selecting presets are Folder and Disc icons.
Tap the Folder icon to load a plugin preset saved on your MPC or any connected drive. Use the window that
opens to select the location where the preset is saved.
Tap the Disc icon to save your plugin settings as a new preset. Use the window that opens to select where you
would like to save the preset.
358
Updates in MPC 2.4
New Features
AIR FX Bundle
Your MPC now includes the AIR FX Bundle—a collection
of 28 effects designed with ease of use in mind with all
new touch-interface layouts. These effects include the
legendary AIR Creative FX collection that has been used
by countless professionals as part of Pro Tools® software
since Version 8. They also include 10 new plugins that
have been expertly designed by the DSP gurus at AIR
Music Technology.
16 classic effects from Pro Tools® now available include
the following:
AIR Distortion
This effect is a multi-type distortion that adds color to
your audio signal with varying types and amounts of
distortion.
Parameter
Value Range
Default Value
Mode
Hard, Soft, Wrap
Hard
Drive
0 – 60 dB
15 dB
Output
0–100%
100%
Mix
0–100% (dry-wet) 100%
Tone Pre-Shape -100 – 0 – +100% 0%
Tone High Cut
1.00 – 20.0 kHz
20.0 kHz
Stereo
On, Off
Off
Clipping Thresh. -20.0 – 0.0 dB FS -10.0 dB FS
Clipping Edge
0–100%
0%
Parameter
Value Range
Default Value
High Gain
0.0 – 12.0 dB
0.0 dB
Low Gain
0.0 – 12.0 dB
0.0 dB
Output
- Inf – 0.0 dB
0.0 dB
Freq. High
1.0 – 10.0 kHz
3.16 kHz
Freq. Low
40.0 – 640 Hz
160 Hz
Harmonics
0.0 – 12.0 dB
0.0 dB
Phase
+ (positive),
- (negative)
+
AIR Enhancer
This effect enhances the low and high broadband
frequencies of the audio signal.
359
AIR Ensemble
This effect applies fluid, shimmering modulation effects
to the audio signal.
Parameter
Value Range
Default Value
Rate
0.01 – 10.0 Hz
1.00 Hz
Depth
0.00 – 24.00 ms
6.00 ms
Width
0–100%
100%
Mix
0–100% (dry–wet) 75%
Mod. Delay
0.00 – 24.00 ms
0.00 ms
Mod. Shimmer
0–100%
50%
AIR Filter Gate
This effect chops your audio signal
into rhythmic patterns with variable
filtering, amplitude and panning.
Parameter
Value Range
Default Value
Pattern
Straight, Pulse, Pumper, Marching,
Fader, Offbeats, Off+Pan, L/R Pan,
LL/RR Pan, Slow Pan, Rand Pan,
Shorter, Longer, Reverse, Random,
Keyed 1–2, Half Time, 12-Step,
Ducked, Trance 1–6, Tech 1–6
Straight
Rate
1/2–1/32, including Dotted and Triplet 1/16
Swing
50.0–66.7%
50.0%
Mix
0–100%
100%
Filter Mode
Off, LP, BP, HP, Phaser
LP
Filter Cutoff
-100 – 0 – 100%
0%
Filter Reso
-100 – 0 – 100%
0%
Gate Attack
0–100%
25%
Gate Hold
0–100%
50%
Gate Release
0–100%
25%
Mod LFO Wave Random; 2–12, 16, 24, 32, 48, 64,
96, 128, 192, 256 Steps
Random
Mod Env
-100 – 0 – 100%
0%
Mod LFO
0–100%
0%
AIR Flanger
This effect applies a short, modulating delay to the audio Parameter
signal.
Rate
Value Range
Default Value
0.02 – 10.00 Hz
0.40 Hz
Depth
0–100%
50%
Feedback
0–100%
50%
Mix
0–100% (dry–wet) 50%
Headroom
-20.0 – 0.0 dB FS -10.0 dB FS
360
AIR Freq Shift
This effect shifts the audio signal's individual frequencies Parameter
for unique effects.
Mode
Value Range
Default Value
Up, Down, Up &
Down, Stereo
Up
Frequency
10.0 mHz – 10.0 kHz 316 mHz
Feedback
0–100%
0%
Mix
0–100% (dry–wet)
100%
AIR Fuzz Wah
This is a multi-effect that combines transistor-like distortion and wah.
Tab
Parameter
Value Range
Default Value
Fuzz-Wah
Mix
0–100% (dry–wet)
100%
Order
Fuzz>Wah, Wah>Fuzz
Fuzz>Wah
Fuzz Mix
0–100% (dry–wet)
100%
Wah Mix
0–100% (dry–wet)
100%
Fuzz Drive
0 – 40 dB
20 dB
Fuzz Tone
1.00 – 10.0 kHz
3.16 kHz
Fuzz Output
-Inf – 0.0 dB
0.0 dB
Fuzz Enable
Off, On
Off
Wah Pedal
0–100%
50%
Wah Filter Mode
Lowpass, Bandpass, Highpass
Bandpass
Min. Freq.
50.0 Hz – 4.00 kHz
428 Hz
Max Freq.
50.0 Hz – 4.00 kHz
2.07 kHz
Min. Resonance
0–100%
55%
Max Resonance
0–100%
33%
Wah Enable
Off, On
On
Mode
LFO, Env
LFO
Rate
LFO
Env
8/4 – 16
0–100%
4T
75%
Depth
-100 – 0 – 100%
0%
Modulation
361
AIR Kill EQ
This effect can zap out the Low, Mid or High broadband
frequency from an audio signal.
Parameter
Value Range
Default Value
High
Thru, Kill
Thru
Mid
Thru, Kill
Thru
Low
Thru, Kill
Thru
Output
-20.0 – +20.0 dB
0.0 dB
High Gain
-Inf – +12.0 dB
0.0 dB
Mid Gain
-Inf – +12.0 dB
0.0 dB
Low Gain
-Inf – +12.0 dB
0.0 dB
High Freq.
500 Hz – 8.00 kHz
2.00 kHz
Offset
-100 – +100%
0%
Low Freq.
50.0 – 800 Hz
200 Hz
AIR Lo-Fi
This effect is used to bit-crush, down-sample, clip, rectify and mangle an audio signal.
Tab
Parameter
Value Range
Default Value
Lo-Fi
Bit Depth
1.0 – 16.0 bit
16.0 bit
Sample Rate
500 Hz – 50.0 kHz
50.0 kHz
Mix
0–100%
100%
Clip
0.0 – 40.0 dB
0.0 dB
Rectify
0–100%
0%
Noise Mod
0–100%
0%
Pre
0.125 – 2.000 Fs
0.5000 Fs
Post
0.125 – 2.000 Fs
1.000 Fs
Enable
On, Off
Off
Wave
Sine, Tri, Saw, Square, Morse,
S&H, Random
Sine
Rate
Sync Off:
Sync On:
0.01 – 10.0 Hz
8/4 – 16
1.00 Hz
2T
Sync
On, Off
Off
Depth
-100 – 0 – 100%
0%
Attack
0.1 – 10.0 s
0.5 s
Release
0.1 – 10.0 s
0.5 s
Depth
-100 – 0 – 100%
0%
Distortion
Anti-Alias
LFO / Env
362
AIR Multi-Chorus
This effect applies a thick, complex chorus effect to your Parameter
audio signal.
Rate
Value Range
Default Value
0.01 – 10.0 Hz
1.00 Hz
Depth
0.00 – 24.00 ms
6.00 ms
Voices
3, 4, 6
4
Mix
0–100% (dry–wet)
50%
Chorus Low
Cut
20.0 Hz – 1.00 kHz
20.0 Hz
Chorus Width 0–100%
100%
Mod Wave
Sine, Tri
Tri
Mod Delay
0.00 – 24.00 ms
6.0 ms
AIR Non-Lin Reverb
This is a spatial effect, designed to produce synthetic,
processed ambience with special gated and reversed
reverb effects.
Parameter
Value Range
Default Value
Pre-Delay
0–250 ms
0 ms
Dry Delay
0–1500 ms
0 ms
Time
0–1000 ms
250 ms
Mix
0–100% (dry–wet) 50%
Diffusion
0–100%
100%
Width
0–100%
50%
Shape
Gated, Reverse
Gated
Low-Cut
20.0 Hz–1.00 kHz 141 Hz
High-Cut
1.00–20.0 kHz
9.46 kHz
AIR Phaser
This effect applies a phaser to your audio signal, for that
wonderful "wooshy," "squishy" sound.
Parameter
Value Range
Default Value
Rate
0.10 – 10.00 Hz
1.00 Hz
Depth
0–100%
50%
Feedback
0–100%
0%
Mix
0–100% (dry–wet)
50%
Phaser Model Vibe, Stone, Ninety,
Tron,
Ninety
Offset
Phase
Rate
Type
-180 – +180 deg.
25–400%
0 deg.
100%
Phase, Rate
Phase
363
AIR Reverb
This is a spatial effect, with a wide range of reverb types to add space or room to your audio signal.
Tab
Parameter
Values
Default Value
Reverb
Pre-Delay
0–250 ms
0 ms
Room Size
0–100%
100%
Time
0.4 ms – +inf s
1.9 s
Mix
0–100%
50%
Type
Off, Booth, Club, Room, Small
Chamber, Medium Chamber, Large
Chamber, Small Studio, Large
Studio, Scoring Stage,
Philharmonic, Concert Hall, Church,
Opera House, Vintage 1, Vintage 2
Off
Length
0–100%
100%
ER / Tail Mix
0–100%
50%
Input Width
0–100%
0%
Output Width
0–100%
0%
Delay
0–250 ms
0 ms
Ambience
0–100%
0%
Density
0–100%
100%
Time
-100 – 0 – 100%
0%
Freq
2.00 – 20.0 kHz
6.32 kHz
Cut
1.0 – 20.0 kHz
9.46 kHz
Time
-100 – 0 – 100%
0%
Freq
20.0 Hz – 2.00 kHz
200 Hz
Cut
1 – 1000 Hz
1 Hz
Early Reflection
Reverb
Room
Hi/Lo Freq
Hi Freq
Lo Freq
AIR Spring Reverb
This is a spatial effect, designed to emulate the sound of Parameter
a spring reverb tank.
Pre-Delay
Value Range
Default Value
0–250 ms
3 ms
Time
1.0–10.0 s
4.0 s
Mix
0–100 (dry–wet)
50%
Diffusion
0–100%
100%
Width
0–100%
0%
Low Cut
20.0 Hz –1.0 kHz
141 Hz
364
AIR Stereo Width
This effect creates a wider stereo presence in an audio
signal.
Parameter
Value Range
Default Value
Width
0–200%
100%
Delay
0.0 – 8.0 ms
0.0 ms
Level Trim
-Inf – 0.0 – +12.0 dB 0.0 dB
Pan Trim
L100 – <C> – R100
<C>
High
0–200%
100%
Mid
0–200%
100%
Low
0–200%
100%
Parameter
Value Range
Default Value
Vowel
OO, OU, AU, AH,
AH
AA, AE, EA, EE, EH,
ER, UH, OH, OO
Env Depth
-100 – 0 – +100%
0%
Formant
-12.00 – +12.00
0.00
Mix
0–100%
100%
LFO Wave
Sine, Tri, Saw,
Square, S&H,
Random
Sine
LFO Rate
Sync Off:
Sync On:
0.01 – 10.0 Hz
8/4 – 16
1.00 Hz
2T
LFO Sync
Off, On
Off
LFO Depth
-100 – 0 – +100%
0%
Env Thresh
-60.0 – 0.0 dB
-30.0 dB
Env Attack
0.1 – 10.0 s
0.5 s
Env Release
0.1 – 10.0 s
0.5 s
AIR Talk Box
This effect adds voice-like resonances to audio signals.
365
12 all new plugins from AIR include the following:
AIR Channel Strip
This specially-designed plugin combines multiple effects with a fast interface. The EQ section provides a
highpass filter, low and high shelves, and a fully parametric mid-band. For dynamics, the AIR Compressor and
Gate algorithms are perfect for achieving hard-hitting drum sounds.
Tab
EQ
Gate/Comp
Parameter
Value Range
Default Value
EQ Enable
Enabled, Bypass
Enabled
Gate Enable
Enabled, Bypass
Enabled
Comp Enable
Enabled, Bypass
Enabled
Output
-Inf – +24.00 dB
0.00 dB
High Shelf Gain
-12.0 – +12.0 dB
0.0 dB
High Shelf Freq
1.20 – 20.0 kHz
6.00 kHz
Mid Gain
-18.0 – +18.0 dB
0.0 dB
Mid Freq
40.0 Hz – 16.0 kHz
247 Hz
Mid Q
0.40 – 10.00
1.00
Low Shelf Gain
-12.0 – +12.0 dB
0.0 dB
Low Shelf Freq
20.0 Hz – 1.00 kHz
100 Hz
HP Filter
0 – 1000 Hz
0 Hz
Gate Thresh
-120.0 – 0.0 dB
-120.0 dB
Gate Depth
0 – -120.0 dB
-120.0 dB
Gate Attack
0.01 – 1000.00 ms
0.18 ms
Gate Release
1.00 – 3000.00 ms
7.40 ms
Comp Thresh
0.0 – -60.0 dB
0.0 dB
Comp Ratio
1.0:1 – 100.0:1
3.9:1
Comp Attack
100 us – 300 ms
5.48 ms
Comp Release
10.0 ms – 4.00 s
200 ms
AIR Compressor
This basic compressor effect changes the dynamic
range of a signal by automatically reducing its gain if it
exceeds a certain level (the threshold).
Parameter
Value Range
Default Value
Threshold
-60.0 – 0 dB
-48.0 dB
Ratio
1.0:1 – 100.0:1
3.9:1
Output
0.0 – 30.0 dB
15.0 dB
Mix
0–100% (dry-wet)
100%
Knee
0–100%
50%
Attack
100 us – 300 ms
5.48 ms
Release
10.0 ms – 4.00 s
200 ms
366
AIR Delay
This is a classic delay line effect with a variable feedback Parameter
filter. Additional Ratio and Width parameters enable you
Time
to achieve a wide range of stereo delay effects.
Sync Off
Sync On
Value Range
Default Value
1 ms – 2.00 s
1/32 – 8/4
388 ms
1/8D
Sync
Off, On
Off
Feedback
0–100%
40%
Mix
0–100% (dry–wet) 50%
Delay Ratio
50:100 – 100:50
Delay HPF
20.0 Hz – 1.0 kHz 20.0 Hz
Delay Width
0–100%
100%
Feedback Damp
1.0 – 20.0 kHz
20.0 kHz
Feedback Reso
0–100%
0%
Fdbk. Reso Freq
100 Hz – 10.0 kHz 1.0 kHz
Parameter
Value Range
Default Value
Time
1/64 – 4/4
(including Triplet
and Dotted
variations)
1/16D
Mix
0–100% (dry–wet) 40%
Feedback
0–100%
50%
Fdbk. Diffusion
0–100%
40%
Fdbk. High Damp 0–100%
35%
Parameter
Value Range
Default Value
Cutoff Freq
55.0 Hz – 20.0 kHz
20.0 kHz
Reso Factor
0.7 – 20.0
1.0
Type
LP4–1, BP2, BP4, HP2_LP1,
HP3_LP1, HP4–1, BR2, BR4,
BR2_LP1, BR2_LP2, HP1_BR2,
BP2_BR2, HP1_LP2, HP1_LP3,
AP3, AP3_LP1, HP1_AP3
LP4
Output Gain
-Inf dB – 0.0 dB
0.0 dB
Saturation
Type
Resample, Bit Crush, Rectify, Hard
Clip, Distort, Overdrive
Overdrive
Saturation
Drive
0.0 – 12.0 dB
0.0 dB
Saturation
Mode
DCF, CVF
DCF
100:100
AIR Diff Delay
This is a delay line effect that is synchronized to your
session tempo and uses an adjustable amount of
diffusion to emulate the dissipation of echoes in
reverberant space.
AIR Filter
This effect applies a filter to the audio
signal and then applies selectable
saturation or reduction to the filtered
signal.
367
AIR Maximizer
This effect is a limiter optimized for professional
mastering.
Parameter
Value Range
Default Value
Threshold
-40.0 – 0.0 dB
-20.0 dB
Ceiling
-20.0 – 0.0 dB FS
-5.0 dB FS
Look Ahead
0.0 – 20.0 ms
0.0 ms
Knee
Hard, Soft
Hard
Release
10.0 ms – 10.0 s
316 ms
LF Mono
10.0 Hz – 1.00 kHz
10.0 Hz
Parameter
Value Range
Default Value
Threshold
-120.0 – 0.0 dB
-48.0 dB
Depth
0 dB – -120.0 dB
-120 dB
Denoise Filter
Off, On
Off
AIR Noise Gate
This effect is similar to a compressor, but instead of
attenuating audio signal that rises above a threshold, a
noise gate attenuates audio signal that falls below a
threshold by a set amount. This can help reduce
background noise in your audio signal.
Denoise Thresh -120.0 – 0.0 dB
-60.0 dB
Attack
0.01 – 1000.00 ms
0.18 ms
Hold
0 – 1000 ms
250 ms
Release
1.00 – 3000.00 ms
7.40 ms
368
AIR Para EQ
This effect is a powerful four-band parametric equalizer
with four independent EQ ranges, adjustable Low and
High EQ filter types, and dedicated Low Cut and High
Cut.
Parameter
Value Range
Default Value
High Freq
1.2 – 20.0 kHz
6.00 kHz
High Q
Shelf
Bell
0.40 – 2.00
0.40 – 10.00
1.00
1.00
High Gain
Shelf
Bell
-12.0 – +12.0 dB
-18.0 – 18.0 dB
0.0 dB
0.0 dB
High Type
Shelf, Bell
Shelf
High Out/In
Out, In
High Mid Freq
120 Hz – 16.0 kHz
2.00 kHz
High Mid Q
0.40 – 10.00
1.00
High Mid Gain
-18.0 – 18.0 dB
0.0 dB
High Mid Out/In
Out, In
Low Mid Freq
40.0 Hz – 16.00 kHz 247 Hz
Low Mid Q
0.40 – 10.00
1.00
Low Mid Gain
-18.0 – 18.0 dB
0.0 dB
Low Mid Out/In
Out, In
Low Freq
20.0 Hz – 1.00 kHz 100 Hz
Low Q
Shelf
Bell
0.40 – 2.00
0.40 – 10.00
1.00
1.00
Low Gain
Shelf
Bell
-12.0 – +12.0 dB
-18.0 – 18.0 dB
0.0 dB
0.0 dB
Low Type
Shelf, Bell
Shelf
Low Out/In
Out, In
Output
-20.0 – +20.0 dB
0.0 dB
High Cut Freq
120 Hz – 20.0 kHz
20.0 kHz
High Cut Type
6, 12, 18, 24 dB
12 dB
High Cut Out/In
Out, In
Low Cut Freq
20.0 Hz – 8.00 kHz 100 Hz
Low Cut Type
6, 12, 18, 24 dB
Low Cut Out/In
Out, In
12 dB
369
AIR Pitch Shifter
This effect alters the pitch of the audio signal and can be Parameter
adjusted based on the source or style of the signal.
Mode
Value Range
Default Value
Vocal, Bass, Beats,
Chords, Textures
Vocal
Shift
-24.0 – 0 – 24.0
0.0
Mix
0–100%
100%
Parameter
Value Range
Default Value
Depth
0–100%
80%
Speed
Bar, 1/2 – 1/32T
1/4
AIR Pumper
This effect creates a rhythmic pumping effect, similar to
that of sidechain compression.
Release Shape 0–100%
10%
Trigger Offset
-100.0 – +100.0 ms
0.0 ms
Attack
0–100%
5%
Hold
0–100%
10%
Release
0–100%
60%
Parameter
Value Range
Default Value
Attack
-100 – 0 – +100%
0%
Attack Shape
0–100%
50%
Sustain
-100 – 0 – +100%
0%
Output
-20.0 – +20.0 dB
0.0 dB
Limit
Off, On
On
AIR Transient
This effect is used to enhance or soften the Attack and
Release phases of audio material.
AIR Tube Drive
This effect is designed to reproduce the sound of an
overdriven tube amplifier.
Parameter
Value Range
Default Value
Drive
0–100%
0%
Headroom
-30.0 – 0.0 dB
-15.0 dB
Saturation
0–100%
50%
Output
-20.0 – +20.0 dB
0.0 dB
AIR Instrument Layouts
MPC now contains stunning new touch-interface layouts for the following AIR Music Technology instrument plugins:
Hybrid, Loom, Vacuum Pro, Velvet, Xpand!2 and theRiser.
370
Clip Program Improvements
Internal Clip Program architecture has been significantly improved, allowing you to play up to 16 clip programs at the
same time. Clips will continue to play when changing tracks or sequences, allowing you to seamlessly integrate them
into live performance.
FLAC and OGG Support
You can now load and export FLAC and OGG files with MPC.
Mother Ducker
You can now apply sidechain ducking effects in MPC using the new Mother Ducker and Mother Ducker Input
insert effects.
Mother Ducker
Add this effect as an insert to the track you want to have
the ducking effect applied to. Use the meters to monitor
the level from your trigger input and tweak the Threshold
and Ratio parameters to adjust the amount of ducking.
The Attack and Release parameters can be used to
sculpt the envelope of the gain reduction to achieve
exactly the pumping effect you are after. Mother Ducker
has eight internal buses so you can set up multiple
channel strips with ducking effects from different
sources.
Parameter
Value Range
Default Value
Ratio
1.00:1 – 60.00:1
6.00:1
Knee
0.000 – 6.000 dB
0.000 dB
Attack
1.0 – 1000.0 ms
10.0 ms
Release
1.0 – 1000.0 ms
100.0 ms
Threshold
-100.000 – 0.000 dB
-6.021 dB
Gain
-100.000 – +12.000 dB -0.000 dB
Auto Gain
On, Off
On
From
Bus 1–8
Bus 1
Parameter
Value Range
Default Value
To
Bus 1–8
Bus 1
Mother Ducker Input
Add this effect as an insert to the track you want to use
as a trigger input, such as a kick drum track.
371
Next Sequence Mode
Next Sequence Mode now remembers the next sequence change when switching to another mode.
Additional Transport Controls
You can now hold Shift and press Stop to return the playhead to the beginning of the timeline.
372
Updates in MPC 2.5
New Features
Splice Integration
Your standalone MPC hardware now integrates with the Splice platform, allowing you to download and browse your
Splice sample library on your standalone device.
To access Splice:
1. First, make sure your MPC hardware is connected to a Wi-Fi network. See Preferences > Wi-Fi to learn how to
connect to a wireless network. You will also need access to a web browser.
2. On your MPC, press Menu and tap the gear icon at the top of the screen to open the Preferences page.
3. Navigate to the Splice tab.
4. Tap the Get Login Code button. (If you are not connected to a network, you will be prompted to do so before
the Get Login Code button appears.)
5. Follow the on-screen instructions to link your MPC to your Splice account via a web browser. It may take your
MPC a few moments to successfully link.
6. A message will appear on screen when the link has been successfully established. Tap OK to continue and
return to the Splice Preferences page.
7. Once the process is complete and your MPC has been paired to your Splice account, tap the Sync Files button
to download samples from your Splice account via Wi-Fi to a drive of your choice.
By default, files will be stored on the Internal drive. You can change the selected drive by tapping the Change
button under Sync Files To Drive.
To browse samples imported from Splice:
1. Open the Browser.
2. Under the Content tab, tap the Splice shortcut icon to view samples downloaded from your Splice account.
If nothing appears, make sure that you have connected your Splice account and synced your files by following
the directions above.
3. The right-side of the browser will display your Splice samples organized into a series of top level folders, allowing
you to easily browse your sample library by BPM, Instrument, Key, Pack or Tag. The All Your Samples folder will
show a list of all samples you have downloaded.
Note: The original sample files are stored in the By Pack folder on your drive. Other folders such as By Instrument
contain internal links to help sort the samples by various tags. If the By Pack folder on your drive is deleted, the files
in the remaining folders will become unusable. To fully remove all files, the entire Splice directory should be deleted.
IMPORTANT: Drives formatted using the FAT32 system do not support these internal links. For these drives, and on
the internal storage drives of some earlier MPCs, samples will only be sorted in the By Pack folder. We recommend
using an exFAT file system on external drives used with MPC, as it is the most robust one supported by both
Windows and macOS.
To view the number of samples available to download from your account, tap the Check For Update button.
To log out of a Splice account, tap the Log Out button.
373
Browser Audition Warp and Sync
In the Browser, you can now audition samples that have an MPC-embedded tempo in sync with the project tempo.
1. Open the Browser by doing either of the following:
• Press Menu and then tap Browser.
• Press Browse (MPC X) or Shift+Menu/Browse (MPC Live, MPC Touch)
2. Tap Audition at the bottom of the screen, or press the respective F-Key (MPC X only).
3. In the options that appear, enable Sync to set samples to be auditioned at the beginning of the next bar of the
sequence when playback is active.
Enable Warp to set samples with an embedded tempo to be warped to the project tempo. Samples with no
embedded tempo or externally-embedded tempo will not be affected by this setting.
4. Select a sample, loop, program or project to preview, then tap the Play button to audition. If Auto Audition is
turned on, samples will audition when selected.
374
Updates in MPC 2.6
New Features
Ableton Live Set Export
You can now export MPC sequences as an Ableton Live
Set (.ALS) file.
To export the current sequence as an Ableton Live Set:
1. Open Main Mode by pressing Main, or by pressing
Menu and then tapping Main.
2. Tap the Project field at the top of the display to open
the Project window.
3. Tap ALS Export.
4. In the window that appears, you can adjust the
following settings for your export:
Use the Export MIDI As settings to choose how MIDI programs and sequences are exported, either as
Audio files or MIDI files. When using Plugin, Drum or Keygroup programs, you can render sequences as
Audio to preserve the sound of the instruments, or render sequences as MIDI data.
Check the Include Program Volume/Pan Settings box to include these settings in the export. When
disabled, the volume and pan settings will be set to 0 dB and center (C), respectively.
Check the Bypass Program Effects Plugins box to deactivate any third-party effect plugins used with the
program for the export. When disabled, those effects will be activated.
Use the Audio Tail field to set the amount, in seconds, of extra time added to the end of the resulting audio
files.
Use the Bit Depth field to set the bit depth to 8, 16 or 24.
Use the Sample Rate field to set the sample rate to 44.1, 48, 88.2 or 96 kHz. In most cases, we recommend
selecting 44.1 kHz.
5. Tap Export to begin the export, or tap Close to cancel and return to the previous page.
Erase Parameters
From the Erase window, you can now erase selected
automation parameters.
1. While the sequence is stopped, press the Erase button
to open the Erase window.
2. Tap Automation to select it.
3. By default, the Parameter field is set to All. Doubletap this field to display a list of all parameters that have
been automated on the current track.
4. Select the parameter you would like to erase, and then
tap Do It to erase the automation.
375
Grid Automation Lanes
You can now input, view and edit automation in Grid View and Audio Edit Mode.
To add automation to a sequence:
1. Select a MIDI program or Audio program.
2. For MIDI programs, tap the grid icon to open Grid View. For Audio programs, tap the waveform-and-box icon
to open Audio Edit Mode.
3. Tap the up arrow on the parameter bar to expand the velocity/automation lane.
4. By default, Velocity is shown in this lane for MIDI programs and PRG: Volume is shown for Audio programs.
Double-tap this field to open the Parameter drop-down menu.
5. In the menu that appears, tap Add New to add an automation parameter. You can choose from a variety of
parameters depending on the type of program, insert effects added and other options.
To edit automation, do any of the following in Grid View or Audio Edit View:
• Use the pencil tool to draw your automation in the automation lane.
• Use the eraser tool to erase automation points. If you erase all automation points, the parameter will be
removed.
• Tap the trash can icon to delete all automation for the selected parameter at once (Grid View only).
You can also edit automation using the Step Sequencer (see below).
376
Step Automation
You can now input, view and edit automation in the Step Sequencer.
To add a step automation parameter:
1. Open the Step Sequencer by doing either of the following:
• Press Menu, and then tap Step Sequencer.
• Press Step Seq (MPC X).
2. By default, the Parameter field of the Step Sequencer displays Velocity for MIDI programs and PRG: Volume
for audio programs. Double-tap this field to open the drop-down menu.
3. In the menu that appears, tap Add New to add an automation parameter. You can choose from a variety of
parameters depending on the type of program, insert effects added and other options.
To edit step automation, do any of the following:
• Tap and drag your finger in the step area to freely draw step values.
• Press and hold the Q-Link button, and then tap Screen to set the Q-Link knobs to Screen Mode. While viewing
the step sequencer, you can use the Q-Link knobs for tactile control of each step's automation value, emulating
traditional knob-based step sequencers. While it is being adjusted, the current automation value will be shown
next to the Parameter field, as well as in the display strip above the knobs (MPC X only).
For MPC Live and MPC Touch, use Bank 1 of the knobs to control Steps 1–4, Bank 2 to control Steps 5–8,
Bank 3 to control Steps 9–12 and Bank 2 to control Steps 13–16.
• Press and hold Shift and tap Clear to clear all automation for the selected parameter in the selected sequence.
• Press and hold Shift and tap Clear Bar to clear all automation for the selected parameter in the current bar of
the selected sequence.
• Use the Nudge < and > buttons to shift the current automation parameter to the left or right at the current Timing
Correct value.
• Use the slider on the right edge of the screen to increase or decrease the parameter values of all automation
steps in the visible time range.
• Tap Presets and use the buttons to apply the presets to the step automation (See Operation > Modes > Step
Sequencer for more information).
Note: When editing step automation, if a step is not activated, a darkened step bar will indicate the current
parameter value at that step, based on the last active step.
377
Submixes
MPC X and MPC Live now contain 8 submixes in Standalone Mode for additional track and program routing options.
To assign an audio track or program to a submix:
1. Press Menu, and then tap Channel Mixer. Alternatively, press Ch. Mixer (MPC X only).
2. Set the Mixer field at the top of the display to Audio Tracks or Programs.
3. Double-tap the Output field of the audio track or program channel strip.
4. In the drop-down menu, scroll to the top of the list and tap to select Sub 1–8. The audio track or program's
audio will now be routed to the selected submix.
To edit a submix:
1. Press Menu, and then tap Channel Mixer. Alternatively, press Ch. Mixer (MPC X only).
2. Set the Mixer field at the top of the screen to Submixes.
3. Use the mixer grid to select a submix, and then use the channel strip on the left side of the screen to add effects
or adjust level, pan and other parameters.
Workflow Enhancements
The Keep or Discard window in Sample Record Mode and the Export Loop as Sample window in Looper Mode
now have easy-access buttons to Save or Edit the recorded sample or loop.
In Sequence Edit Mode, you can now copy events from individual or multiple pads or notes from the Copy Events
window.
In the Sequence Edit > Copy Sequence and Track Edit > Copy Track windows, you can now rename the
destination sequence or track.
The FX list can now be sorted by type of effect for easier navigation.
Timing Correct can now be applied to all tracks by pressing the All Track button in the Timing Correct window.
378
Updates in MPC 2.7
New Features
Ableton Live Control
Your MPC X or MPC Live hardware is now pre-mapped to control Ableton Live 10.1.2 or later for instant performance
and production setup, providing an unparalleled level of integration with Ableton Live from a standalone device.
MPC's Live Control Mode has been carefully designed to allow you to instantly switch between using MPC X or MPC
Live in standalone mode and Live Control mode without ever stopping playback. You can control Ableton Live over a
Wi-Fi network for cableless operation, or connect MPC X or MPC Live to your computer using a USB-to-Ethernet
adapter for a more tightly controlled setup.
To get started with Ableton Live Control, you will need to follow the directions in the sections below download,
install and configure the necessary software.
Akai Network Driver
The Akai Network Driver will allow your MPC X or MPC Live to seamlessly communicate with and control Ableton
Live.
1. Download the Akai Network Driver from akaipro.com and install it by following the directions.
2. Once the installation has completed, restart your computer.
3. Power on your MPC.
4. Press Menu and tap the gear icon to open the Preferences menu.
5. Tap Wi-Fi to open the Wi-Fi settings. Make sure Wi-Fi is set to On, and then connect to your local wireless
network.
Alternatively, you can connect MPC to your network using a USB-to-Ethernet adapter. In this case, select
Ethernet from the Preferences menu and make sure the Enabled option is checked.
6. Open the Akai Network Driver application.
7. In the Configured Remote Device field, locate the IP address and Serial Number of your MPC and select it. If
you need to verify you are selecting the correct unit, you can view network information on your MPC in the Wi-Fi
menu by holding Shift and tapping Info.
8. If you still do not see your unit's Serial Number and IP, click the Add a Device button to manually enter your
unit's IP address.
9. Once your unit has been successfully configured, you can rename it by pressing the Rename a Selected Device
button. When you are finished, you can close the Akai Network Driver application and open Ableton Live.
Configuring Ableton Live
1. Important: To use MPC v2.7 to control Ableton Live, you will need to download and install version 10.1.2 or
later.
2. Open Ableton Live 10.1.2 or later.
3. Open the Preferences menu by selecting Live > Preferences.
4. Make sure you have selected your preferred Audio Device in the Audio tab.
5. In the Link / MIDI tab, click the first available Control Surface field and select Akai Force MPC.
6. In the same row, select Akai Network – DAW Control as the Input and Output.
7. Under the MIDI Ports section, set Remote for the Akai_Force_MPC Input and Akai_Force_MPC Output to
On.
Once the previous steps have been completed, you can begin controlling Ableton Live with your MPC.
379
Live Control Mode
To open Live Control mode, press Menu (or tap the icon in the upper-left corner of the screen) on your MPC X
or MPC Live and then tap Live Control.
Alternatively, press and hold the Menu button and then tap Pad 4 to jump to Live Control mode.
To exit Live Control mode, press Menu (or tap the icon in the upper-left corner of the screen) on your MPC X or
MPC Live and then select another mode.
Alternatively, press and hold the Menu button and then tap a pad to jump to another mode.
Live Control Mode consists of three main views, which can be selected by tapping the tabs on the left side of the
display: Matrix View, Mixer View and Device Control View. Click the links to jump to that section.
In each of these modes, you will always have access to the following controls and functions on the display:
Tap a track name to select it.
Tap the stop icons at the bottom of the display to stop clips in the selected track.
Tap the Launch Quantize field (above the scene launch arrows) to set the Launch Quantize value.
Tap the Scene Launch arrows on the right side of the display to launch all clips in that row.
Additionally, MPC's hardware controls are pre-mapped to give you hands-on control of parameters and functions.
See the MPC X Control Map and MPC Live Control Map for the complete mappings.
Control Bar
At the top of the interface is the Control Bar. This toolbar can be configured to one of three presets based on typical
Ableton Live use cases in the Settings window.
To open the Settings window, tap the gear icon in the top-right corner of the display.
Use the Control Bar field to select one of the three preset configurations: Settings, Arrangement or
Performance.
• Session: The Session View configuration is ideal for working in Ableton Live's 8x8 clip launch matrix.
Use the BPM field to adjust the tempo in Ableton Live.
Tap the Phase Nudge Down and Phase Nudge Up icons to temporarily decrease or increase the tempo
in Ableton Live.
Tap the metronome icon to enable to disable the metronome in Ableton Live.
Tap the follow icon to turn following on or off. When set to on, your Ableton Live software display will
move along with playback to keep the current playback position in view. You can adjust the Follow
Behavior in Ableton Live's Preferences.
Use the Position field to select the playback position.
Tap the + icon to enable or disable MIDI Arrangement Overdubbing.
Tap the automation icon to enable to disable automation recording.
• Arrangement: The Arrangement configuration is ideal for working with Ableton Live's linear Arrangement
view.
Use the BPM field to adjust the tempo in Ableton Live.
Use the Position field to select the playback position.
Use the Start field to select the Arrangement loop start point.
Tap the loop icon to enable or disable Arrangement looping.
Use the Length field to select the Arrangement loop length.
• Performance: The Performance configuration is ideal for real-time performance with Ableton Live.
Use the BPM field to adjust the tempo in Ableton Live.
Tap the Phase Nudge Down and Phase Nudge Up icons to temporarily decrease or increase the tempo
in Ableton Live.
Use the Quantize To field to set the time division for quantization: 1/4, 1/8, 1/8T, 1/8 and 1/8T, 1/16, 1/16T,
1/16 and 1/16T or 1/32.
380
Matrix View
The Matrix View provides an overview of the clip matrix from Ableton Live's Session view, displaying up to eight
tracks and eight rows of clips on the display. The tracks and clips displayed on your MPC's touchscreen will be
shown in Ableton Live with a colored box outline.
Your MPC's pads control up to four tracks and four rows of clips, marked by a white outline on the display.
To move the 4x4 Session Matrix focus one row or column at a time:
MPC X: Use the cursor buttons.
MPC Live: Use the Bank buttons.
To move the 4x4 Session Matrix focus by eight rows or eight columns at a time:
MPC X: Hold Shift and use the cursor buttons.
MPC Live: Hold Shift and use the Bank buttons.
To launch a clip from the 4x4 Session Matrix, press the corresponding pad on your MPC X or MPC Live.
You can also use the pads to launch scenes.
To toggle between launching clips and scenes:
MPC X: Press the XYFX button.
MPC Live: Press the 16 Level button.
To launch a scene, press a pad in the corresponding row.
See the MPC X Control Map and MPC Live Control Map for more information.
All tracks, clips and scenes will display the same color and names as assigned in Ableton Live. The pads on your
MPC hardware will also change color depending on the playback or recording state:
When a clip is stopped, it will display the color set in Ableton Live on both the hardware pads and display.
When a clip is playing, the hardware pad will blink green, and the clip on the display will fill with white based on
the clip length.
When a clip is preparing to record, it will flash red on both the hardware pads and display until the launch
quantization value is reached.
When a clip is recording, it will blink red on the hardware pads and be lit red on the display.
You can also access the following controls and features by tapping the buttons at the bottom of the display:
Tap Quantize at the bottom of the screen to quantize the currently selected clip according to the Quantize To
value (set in the Ableton Live Control Settings).
Tap Delete at the bottom of the screen to delete the currently selected clip.
Tap Insert Scene at the bottom of the screen to insert a new scene after the currently selected clip.
Tap Rec at the bottom of the screen to enable or disable Ableton Live's Arrangement Record. Use this to
capture your Session performance into the Arrangement view.
381
Mixer View
The Mixer View gives you control of Ableton Live's key mixing features, such as levels, stereo panning, sends and
returns and more. Use the tabs at the bottom of the display to select what information is shown on MPC's display.
• Levels: The Levels tab gives you an overview of the volume level of your tracks, including the Returns and the
Master track.
Tap a level slider and then use the data dial or –/+ buttons to adjust the volume level of the currently
selected track, return or master. Alternatively, tap and drag a level slider to adjust the volume level.
The level sliders and meters in each pad show a visual representation of the level. Double-tap a track on the
screen to open a large version of the level slider and meter.
• Main: The Main tab gives you a full channel strip with a number of mixing options for your tracks.
Tap the track activator (under the track name) to enable or disable (mute) the track.
Tap the S button to solo the track.
Tap the record button to arm the track for recording.
The pan sliders in each track show a visual representation of the pan. Tap a pan slider and then use the
data dial or –/+ buttons to adjust the panning of the currently selected track, return or master. Alternatively,
tap and drag the pan slider to adjust the panning. Double-tap a pan slider on the screen to open a large
version of the slider.
Tap a level slider and then use the data dial or –/+ buttons to adjust the volume of the currently selected
track, return or master. Double-tap a level slider on the screen to open a large version of the slider.
Alternatively, tap and drag a level slider to adjust the volume level.
• Sends: The Sends tab gives you an overview of the Send and Return controls in Ableton Live.
Use the send knobs to adjust the send level of tracks. Tap the knob and use the data dial or –/+ buttons to
adjust the level. Alternatively, tap and drag the send knob to adjust the send level.
Tap the A or B icons to assign the track to the Ableton Live's A or B cue mix.
Device Control View
The Device Control View allows you to control MIDI Instruments, Audio Effects and other Devices in Ableton Live
directly from your MPC. The current view of the Device Control Tab is determined by the "blue hand" remote control
icon in Ableton Live's Detail View.
Tap the Track Name under the Control Bar to select the Track. If there is a Device(s) associated with the Track,
the first will be shown below.
Tap the lock icon on the right side to lock parameter changes to the device.
Use the sliders to adjust the parameters of the device. Tap a slider and then use the data dial or –/+ buttons to
adjust the parameter. Alternatively, tap and drag a slider to adjust the parameter.
Use the Device – and + buttons to change devices on the same track. The white and grey boxes below the
parameter sliders represent the number of available Devices.
Use the Bank – and + buttons to cycle through banks of controls for the device, if available. For internal Ableton
Live plugins, you will see the name of the current bank. For third party plugins, you will see the number of the
current bank.
Tap Device On to enable or disable (bypass) the device.
Q-Links
The Q-Links on your MPC give you hands-on control of Ableton Live's key parameters.
On MPC X, Q-Links 1–8 control track volume for the eight tracks currently in view, while Q-Links 9–16 control the
device on the currently selected track, based on the "blue hand" in Ableton Live's Detail View. The OLED screens
above each Q-Link also provide clear visual feedback of the parameter name and value being controlled.
On MPC Live, Q-Link Banks 1 and 2 control track volume, and Q-Link Banks 3 and 4 control the current device at
the "blue hand" position. Press and hold the Q-Link button to bring up the Q-Links Overview on the touchscreen,
where you can view the current assignments and quickly select another bank.
382
MPC X Control Map
1
26
27
24 25
22 23
28 29 30 31 32
18
19 20 21
3
17
33
4
5
2
7
13 14
6
15 16
8 9 10 11 12
General Controls and Features
#
Device Control
Ableton Live Function
1
Display
In Ableton Live Control Mode, MPC X's display will show a dynamic representation of
Ableton Live's software.
2
Pads
Press the pads to launch clips or scenes. Press the XYFX button to toggle between
launching clips (the button is off) and launching scenes (the button is on).
3
Data Dial
Adjusts the highlighted field.
4
-/+
Decreases or increases the value of the highlighted field.
5
Numeric Input
If the selected field on the screen is a number, press these numbered buttons as you
would on a standard numeric keypad to enter a value. Press the keypad’s Enter to enter
it. (A numeric keypad with additional operations will appear on the screen, as well.)
6
Directional Cursors
Moves the 4x4 Session Matrix focus on the display by one row or one column at a time.
7
Shift
Hold this button to access secondary button functions. See Shift Controls for more
details.
383
Transport Controls
#
Device Control
Ableton Live Function
8
Record
Enable and disable Arrangement Record
9
Overdub
Enable and disable Session Record.
10 Stop
Stop playback.
11 Play
Start playback from the Stop position.
12 Play Start
Start playback from the Arrangement start (1:1:1).
13 <
Move Playhead back by one bar
14 >
Move Playhead forward by one bar
15 <<
Phase Nudge down
16 >>
Phase Nudge up
Right-Hand Side Buttons
#
Device Control
Ableton Live Function
17 Tap Tempo
Tap this button at the desired rate to set a new tempo in Ableton Live.
18 XYFX
Toggles the MPC pads between launching clips (XYFX off) and launching scenes (XYFX on).
19 Erase
Deletes the selected clip.
20 Undo
Undo the last action.
21 Copy
Duplicates the selected clip into the next available clip slot.
22 Mute
Mutes/deactivates the current track.
23 Solo
Solos the current track.
24 Rec Arm
Arms the current track for recording.
25 Read/Write
Arms Global Automation.
Left-Hand Side Buttons
#
Device Control
Ableton Live Function
26 Next Seq
Opens the Ableton Clip Launch Matrix tab
27 Ch. Mixer
Opens the Ableton Mixer tab.
28 Q-Link Project
Moves to the previous device.
29 Q-Link Program
Moves to the next device.
30 Q-Link Pad Scene
Device Control Bank Left
31 Q-Link Pad Param
Device Control Bank Right
32 Q-Link Screen Control Opens the Ableton Device Control tab
33 Q-Links
Adjusts the currently selected parameters displayed in the OLED screens above.
Q-Links 1–8 control track volume for the eight tracks currently in view, while Q-Links 9–
16 control the device on the currently selected track, based on the "blue hand" in Ableton
Live's Detail View.
384
Shift Controls
Press and hold MPC X's Shift button, and then press the following buttons for additional actions.
#
Device Control
Ableton Live Function
2
Pads
Selects a clip without launching it.
6
Directional Cursors
Moves the 4x4 Session Matrix focus on the display by eight rows or eight columns at a
time.
10 Stop
Stop playback and return song position to 1:1:1.
17 Tap Tempo
Toggle the metronome on and off.
21 Undo
Redo the last action.
MPC Live Control Map
7
8
9
12
10
11
5
6
6
1
6
2
13
14 15 4
6
3
16 17 18 19 20 21 4
Basic Controls
#
Device Control
Ableton Live Function
1
Display
In Ableton Live Control Mode, MPC Live's display will show a dynamic representation of
Ableton Live's software.
2
Pads
Press the pads to launch clips or scenes. Press the 16 Level button to toggle between
launching clips (the button is off) and launching scenes (the button is on).
3
Data Dial
Adjusts the highlighted field.
4
-/+
Decreases or increases the value of the highlighted field.
5
Q-Link Button
Press this button to move forward between Q-Link Banks 1–4. Push and hold this button
to bring up the Q-Links Overview window on the display.
385
#
Device Control
Ableton Live Function
6
Q-Links
Adjusts the currently selected parameters.
Use the Q-Link button to toggle between Q-Link Banks 1 and 2 (which control Track
Level for the eight tracks currently viewed) and Banks 3 and 4 (which are mapped to
control the device on the current track, based on the location of the "blue hand" in
Ableton Live's Detail View).
7
Bank A/E
Move the 4x4 Session Matrix focus up by one row.
8
Bank B/F
Move the 4x4 Session Matrix focus down by one row.
9
Bank C/G
Move the 4x4 Session Matrix focus left by one column.
10 Bank D/H
Move the 4x4 Session Matrix focus right by one column.
11 Erase
Deletes the selected clip.
12 16 Level
Toggles the MPC pads between launching clips (16 Level off) and launching scenes (16
Level on).
13 Shift
Hold this button to access secondary button functions. See Shift Controls for more
details.
14 Undo
Undo the last action.
15 Copy
Duplicates the selected clip into the next available clip slot.
16 Tap
Tap this button at the desired rate to set a new tempo in Ableton Live.
17 Rec
Enable and disable Arrangement Record.
18 Overdub
Enable and disable Session Record.
19 Stop
Stop playback.
20 Play
Start playback from the current playhead position.
21 Play Start
Start playback from the Arrangement start (1:1:1).
Shift Controls
Press and hold MPC's Shift button, and then press the following buttons for additional actions.
#
Device Control
Ableton Live Function
2
Pads
Selects a clip without launching it.
5
Q-Link Button
Move backward between Q-Link Banks 1–4.
7
Bank A/E
Move the 4x4 Session Matrix focus up by eight rows.
8
Bank B/F
Move the 4x4 Session Matrix focus down by eight rows.
9
Bank C/G
Move the 4x4 Session Matrix focus left by eight columns.
10 Bank D/H
Move the 4x4 Session Matrix focus right by eight columns.
13 Undo
Redo the last action.
15 Tap
Toggle the metronome on and off.
18 Stop
Stop playback and return song position to 1:1:1.
386
Ethernet Adapter Support
MPC X and MPC Live now support USB-to-Ethernet adapters. Ethernet settings can be set in the Ethernet tab of the
Preferences menu.
Improved Preferences Organization
The Preferences menu has been updated with improved organization. Wi-Fi, Ethernet and Bluetooth tabs have been
grouped and are now located beneath the Info tab. (This has been updated in Operation > General Features >
Menu > Preferences.)
Corrections
Operation > Modes > Main Mode > Track Section (page 121)
Operation > Modes > Main Mode > Program Section (page 131)
Operation > Modes > Program Edit Mode (page 189)
We removed the following sentence related to plugin programs on standalone MPC hardware:
For MPC X and MPC Live, plugin programs are available only in Controller Mode with the desktop version of the
MPC software.
387
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising