Rane | RS 1 | Data Sheet | Rane RS 1 & 2 Remote Power Supply Data Sheet

Rane RS 1 & 2 Remote Power Supply Data Sheet
RS 1/RS 2
Professional Audio Products Data Sheet
120 VAC REMOTE POWER SUPPLIES
A
RS 1
4.2"/10.7
RS 2
4.3"/11
B
C
D
E
cm
3.7"/9.4
cm
1.9"/4.8
cm
2.2"/5.6
cm
1.7"/4.3
cm
cm
3.8"/9.6
cm
2.2"/5.6
cm
2.7"/6.8
cm
2.2"/5.6
cm
General Description
The RS 1 Remote Power Supply is a general purpose AC
to AC adapter designed to power any Rane products equipped
with red AC remote power mod jacks. And since the output
voltage is classified as safety extra-low voltage, then all units
powered from this unit are exempt from safety agency
approval requirements.
The table-top design of the RS 1, along with a 2 meter line
cord and the 2 meter output cable, allows it to be installed in
any convenient location away from the powered unit and the
AC outlet strip. Convenient mounting tabs are integral to the
rugged high impact housing. Tip: RS 1’s mount diagonally on
standard EIA rack spacing (4").
Daisychaining Precautions: Daisychaining is acceptable
only where balanced wiring is used exclusively (see the Flex
User's Guide for more details), and the total current demand
of all products being powered does not exceed the maximum
output current rating.
The connector wiring (see diagram) of the RS 1/RS 2
allows for easy daisychaining. Plug a 6-wire modular wye
adaptor (male to 2 females) into the first product to be
powered. Connect the RS 1/RS 2 output cable into one side of
this adaptor, and then use another 6-wire mod cable from the
other side of the adaptor to the
next unit to be powered.
IMPORTANT: BOTH THE
ADAPTOR AND THE CABLE
MUST BE 6-WIRE; 4-WIRE
VERSIONS WILL NOT WORK.
Caution—Thermal Switch Resetting
If the thermal protection switch is activated (due to short circuit, etc.):
1. Remove the AC mains power.
2. Wait 15 minutes for the thermal switch to reach ambient temperature and reset itself.
3. Reapply AC mains power.
Caution—Damage to the power supply will occur if this supply is plugged into older Rane
products with DC (black color) power jacks. Use only with AC (red color) power jacks.
Parameter
Output Voltage
Maximum Output Current
Max/Min Output Voltage
Input Cord
Output Cord
Safety Agency
..........U.L. Listed
..........C.S.A. Certified
Maximum Power
Line Voltage
Enclosure
Weight
Specifications
18 CT (center-tap: 9+9)
750/1500
23.3 CT/16.2 CT
2-Wire, 2-Prong AC Line Cord
6-Wire Modular RJ-12 Plug
E90493 & E88261
LR91687 & LR58948
25/46.5
105-130VAC, 50/60Hz
Black High Impact Plastic
1.5 lb/2.0 lb
Limit
10%
+10%
10%
Units
VAC
mA
VAC
W
Conditions/Comments
Rated Load, 120VAC line
RS 1/RS 2
No-Load/Full-Load, ±10% Line
18 AWG, 6 Feet Long
26 AWG, 6 Feet Long
Class 2 Transformer
U.L. 1012
C.S.A. C22.2 No. 223
RS 1/RS 2
With Integral Mounting Tabs
(0.7 kg/0.9 kg) RS 1/RS 2
RS 1/RS 2
Professional Audio Products Data Sheet
230 VAC REMOTE POWER SUPPLIES
A
RS 1
10.7
RS 2
11
B
C
D
E
cm
9.4
cm
4.8
cm
5.6
cm
4.3
cm
cm
9.6
cm
5.6
cm
6.8
cm
5.6
cm
General Description
The RS 1/RS 2 Remote Power Supply is a general purpose AC
to AC adapter designed to power any Rane products equipped with
red AC remote power mod jacks. The RS 1 and RS 2 meet the EN
60950 Safety Standard and comply with the European EMC
directive 89/336/EEC. And since the output voltage is classified as
safety extra-low voltage, then all units powered from this unit are
exempt from safety agency approval requirements.
The 230VAC version of the RS 1/RS 2 comes from the factory
with an integral mounted Eurocord.
The table-top design of the RS 1/RS 2, along with the two meter
line cord and the two meter output cable, allows installation in any
convenient location away from the powered unit and the AC outlet
strip. Convenient mounting tabs are integral to the rugged high
impact housing.
Daisychaining Precautions: Daisychaining is acceptable only
where balanced wiring is used exclusively (see the Flex User’s
Guide for more details), and the total current demand of all products
being powered does not exceed the maximum output current rating.
The connector wiring (see diagram) of the RS 1/RS 2 allows for
easy daisychaining. Plug a 6-wire modular wye adapter (male to 2
females) into the first product to be powered. Connect the RS 1/RS
2 output cable into one side of this adapter, and then use another 6wire mod cable from the other side of the adapter to the next unit.
IMPORTANT: BOTH THE ADAPTER AND THE CABLE
MUST BE 6-WIRE; 4-WIRE VERSIONS WILL NOT WORK.
Caution—Thermal Switch Resetting
If the thermal protection switch is activated (short circuit, etc.):
1. Remove the AC mains power.
2. Wait 15 minutes for the thermal switch to reach ambient
temperature and reset itself.
3. Reapply AC mains power.
Caution—Use only with Rane products with AC (red color) power
jacks. Damage will occur into older DC (black color) power jacks.
Finnish Note: Laitteen verkkoliitantajomtoa ei voi vaihtaa johdon
viottuessa on koko verkkomuuntaja johtoineen vaimdettava uuteen.
Swedish Note: Anslutningssladden till denna transformator kan icke
ersattas. Om sladden skadas skall darfor transformatorn kasseras.
Parameter
Output Voltage
Maximum Output Current
Max/Min Output Voltage
Input Cord
Output Cord
Safety Agency
..........EMC
..........IEC
..........Scandinavian
Maximum Power
Line Voltage
Enclosure
Weight
Specifications
2x9 CT (center-tap: 9+9)
750/1500
23.3 CT/16.2 CT
Class II, CEE 7/16
6-Wire Modular RJ-12 Plug
European Directive 89/336/EEC
Meets EN 60950 Standard
Approved Semko, Nemko
20/46.5
190-250 VAC, 50 Hz
Black High Impact Plastic
0.7 kg/0.9 kg
Limit
10%
+10%
10%
Units
VAC
mA
VAC
Conditions/Comments
Rated Load, 230 VAC line
RS 1/RS 2
No-Load/Full-Load, ±10% Line
Eurocord, 2 Meters Long
26 AWG, 2 Meters Long
Class II Transformer
E1 and E2 Environments
TUV Approved With GS Mark
W
RS 1/RS 2
With Integral Mounting Tabs
RS 1/RS 2
©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5098 TEL (206)355-6000 FAX (206)347-7757 WEB http://www.rane.com
Printed in the U.S.A. on Recycled Paper
All features & specifications subject to change without notice 520-290 MAY96
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising