Rane | RAD16z | Information Sheet | Rane RAD16z Halogen Interface with Dual Inputs / Dual Outputs / Dual Logic I/O Information Sheet

Rane RAD16z Halogen Interface with Dual Inputs / Dual Outputs / Dual Logic I/O Information Sheet
RAD16z
Manual Version v1.1
Introduction & Support
Thanks for purchasing the Rane RAD16z. It’s a finely crafted interface for the HAL system, converting analog audio to and/or
from 24-bit, 48 kHz digital audio. RAD16z is an alternative to standard switch boxes for impractical areas such as stage floor
pockets or above ceilings. The operating manual and all related software documentation can be found at rane.com/hal
For system applications, design examples and related HAL information, please see the HAL Notes library at rane.com/library
If you need additional assistance, please contact our HAL technical agents at halogen@rane.com
For additional product support, visit rane.com/support
Panels
(Front & Rear)
Technical Specifications
Digital Codec
Inputs
24-bit, 48 kHz
1
Euroblock, 6 pins, 3.81 mm pitch, green
Microphone Impedance
2.16 kΩ
1%, balanced, 1.08 kΩ + 1.08 kΩ
(level set in
software)
Gain Range (dynamic)
+26 to +46 dB Typical, 1 dB steps
Gain Range (condenser)
+14 to +34 dB Typical, 1 dB steps
Maximum Input (dynamic)
-16 dBu
Minimum, balanced, gain = 26 dB
Maximum Input (condenser)
-4 dBu
Minimum, balanced, gain = 14 dB
Equivalent Input Noise
-121 dBu
Typical, 20 kHz BW, RS = 150 Ω, 26 dB gain
CMRR
-70 dB
Typical, RS = 150 Ω, 1 kHz, 26 dB gain
Frequency Response
20 Hz – 20 kHz Typical, +0.0/-0.5 dB, at all gain settings
THD+N
< 0.010%
Typical, @ 1 kHz, 20 kHz BW, Rs = 150 Ω, -6 dBFS output, 26 dB gain
Phantom Power
+24 V
2%, 10 mA maximum
Impedance
10 kΩ
1%, balanced
Gain Range
0–20 dB
Typical
Maximum Input (Line Mode)
14 dBu
Minimum, < 1% THD
Line/Line+
Connectors
(balanced)
Maximum Input (Line+ Mode) 14 dBu
Typical, @ 1 kHz, active, left [+] & right [–] signals summed to mono
Dynamic Range
103 dB
Typical, 0 dBFS, 20 kHz BW, A-weighted, unity gain
CMRR
-50 dB
Typical, Rs = 150 Ω, 1 kHz
Frequency Response
20 Hz – 20 kHz Typical, +0.0/-0.5 dB
rane.com
RAD16z
Outputs
Connectors
1
Euroblock, 6 pins, 3.81 mm pitch, orange
Impedance
200 Ω
1%, each leg
Maximum Output
14 dBu
Minimum, < 1% THD, 10 kΩ load
Dynamic Range
106 dB
Typical, 0 dBFS, 20 kHz BW, A-weighted
Frequency Response 20 Hz – 20 kHz
Typical, +0.0/-0.5 dB
THD+N
0.008%
Typical, @ 1 kHz, 20 kHz BW, -6 dBFS output, RAD16z input to output
Signal
-50 dBFS
Unbalanced/balanced output, green LED, peak-reading
Overload
-0.5 dBFS
Unbalanced/balanced output, red LED, peak-reading
Connectors
1
RJ-45
Cable Length
500 ft. / 152 m
Shielded Cat 5e cable or better; must be shielded
Connectors
1 (shared)
Euroblock, 6 pins, 3.81 mm pitch, black, contact closure to ground
Internal Pull-Up
51.1 kΩ, 5.0 V
Protected to +24 V
High-Input Level
> 2.0 V
Minimum, normal state
Low-Input Level
< 0.9 V
Maximum, external circuit must sink > 80 μA to assert
Connectors
1 (shared)
Euroblock, 6 pins, 3.81 mm pitch, black, relay drive, LED or logic
level output
Internal Pull-Up
1.0 kΩ, 5.0 V
Protected to +30 V, reverse-polarity-protected
Sink Current
200 mA
Maximum, output FET on
LED Drive Current
2 mA
Output FET off, driving an LED with Vf = 2.0 V
High-Output Level
4.7 V
Minimum, output FET off, 0 mA output current
Low-Output Level
0.1 V
Maximum, output FET on, < 200 mA sink current
Dimensions
4.92” x 3.31” x 1.05”
12.5 x 8.4 x 2.7 cm
Width x depth x height
Weight
11.9 oz.
337 g
Indicators
RAD Port
Logic
Inputs
Outputs
Specifications are subject to change without notice. Rane is a trademark of inMusic Brands, Inc., registered in the U.S. and other countries. All
other product names, company names, trademarks, or trade names are those of their respective owners.
rane.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising