Lorex | LWF2080B-64 | Quick Connection Guide | Lorex LWF2080B-64 1080p Wire Free Camera System, 4 Battery Powered Black Outdoor Metal Cameras, Ultra-Wide Lens, 65ft Night Vision, Two-Way Audio Speaker-Mic, 1TB Hard Drive Quick Connection Guide

Lorex LWF2080B-64 1080p Wire Free Camera System, 4 Battery Powered Black Outdoor Metal Cameras, Ultra-Wide Lens, 65ft Night Vision, Two-Way Audio Speaker-Mic, 1TB Hard Drive Quick Connection Guide
STEP 2: Setting Up the Recorder
Next, you must set up the recorder and connect the wireless receiver.
To set up the recorder:
1. Connect the wireless receiver to
the USB port on the back panel of
the recorder.
NOTE: The receiver includes double-sided tape and
mounting screws for optional wall mounting for
improved line-of-sight with cameras.
HD Wire-Free Security System G2
GUIDE
2. Connect the recorder to your router
using the included Ethernet cable.
1/2
LHB926 / LHB927
Quick Connection Guide
English Version 1.0
www.lorex.com
Package Contents
3. Connect the included power
adapter to the recorder. Wait a few
minutes for the system to start
up.
* Per camera in multi-camera packs
OPTIONAL: Full Recorder Setup
OR
HD Recorder
HD Wire-Free Security Cameras
(Model Number: LHB926 / LHB927)
Wireless Receiver
& Antennas
Rechargeable
Power Pack*
(Model Number: LWB4800 / LWB4900 / LWB5800 / LWB6800 Series)
• This guide describes basic setup of the recorder
only. This installation is intended for users who
wish to monitor their system using the free Lorex
Cirrus app on their smartphone or tablet.
HDMI OR
• You may choose to connect the included USB
mouse and a monitor with HDMI or VGA cable (not
included) for complete control over your WireFree security system using the recorder. See the
included Quick Reference Guide for details.
Camera Antenna*
USB Mouse
Toolkit
VGA*
* Not included
HDMI Cable
STEP 3: Connecting with Lorex Cirrus
Camera Mounting Kit*
Remote Control
Recorder Power
Adapter
Ethernet Cable
Power Pack
Adapter
STEP 1: Initial Setup
Before you begin, you will need to prepare the Wire-Free cameras and Power Packs.
NOTE: Power Packs come fully charged with no need for initial charging.
To prepare the cameras:
LWB4800 / LWB4900 Series
1. Attach an antenna to each camera. For
LWB4800 / LWB4900 Series cameras,
twist the adjustment ring counterclockwise
to reposition each camera as shown to
the right. Twist clockwise to tighten when
finished.
Connect to your system using the free Lorex Cirrus app for smartphones and
tablets (iOS and Android).
To connect with Lorex Cirrus:
1. Download and install the free Lorex Cirrus app from the
App Store or Google Play Store.
2. Tap the Lorex Cirrus icon to launch the app.
LWB5800 / LWB6800 Series
3. Tap
to open the menu. Tap Devices, then tap Add.
4. Enter the following:
F
Adjustment
ring
2. Peel off the PLEASE REMOVE label
covering the contacts on each Power
Pack. Insert the charged Power Packs
into each camera base. Push up until the
Power Pack ‘clicks’ into place.
NOTE: The camera will ‘beep’ when the
Power Pack is properly inserted. If you do
not hear this alert, remove the Power Pack
by pushing on the release tabs then reinsert.
3. Connect the two black antennas to the
wireless receiver.
A
B
A Ensure Device ID is selected.
B Tap to scan the QR code on the top
of your recorder using the camera on
your mobile device.
C Ensure the Client Port reads 35000.
D Enter the username (default: admin).
E Enter the password (default:
00000000).
F Tap Save.
C
D
E
5. Enter a new, secure 8-15 character password. This password will be used
to connect to your system from now on.
Record your password below and store in a secure place:
6. Your cameras will appear on the Live screen of the app. Tap the play
) to stream live video on channels that are in sleep mode.
button (
Initial setup is now complete! Turn the guide over for instructions on
positioning and mounting the cameras.
Need Help?
Visit us online for up-to-date software and complete instruction manuals.
Dimensions
1.9”
48mm
11.8”
300mm
1
Visit lorex.com
2
Search for the model number
of your product
3
Click on your product in the
search results
4
Click on the Downloads tab
Copyright © 2019 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right to modify product design,
specifications and prices, without notice and without incurring any obligation. E&OE. All rights reserved.
8.2”
208mm
LWB4800 / LWB4900 Series
5.3”
130mm
LWB5800 / LWB6800 Series
5.5”
134mm
2.9”
73mm
5.0”
126mm
2.9”
73mm
6.6”
168mm
LHB926_LHB927_QCG_EN_R1
STEP 4A: Installation Tips
Optimizing Motion Detection
Follow the tips below for more accurate motion detection and to optimize battery life:
Customize motion detection settings to ensure motion events are being recorded and
reduce false alarms.
• See images to the right for ideal setup. It is recommended to
place your camera at least 7ft (2.1m) above the ground and
angle it slightly downward toward the monitoring area, excluding
any busy areas (e.g., sidewalks or roadways).
• Ensure the camera image is free of obstructions (i.e., tree
branches).
• Position the camera no more than 20ft (6.1m) away from the
area you wish to monitor.
• See the “Optimizing Motion Detection” section to customize
motion settings for each camera on your system.
• For best performance, position the camera so that objects of
interest will move from side-to-side across the camera image,
rather than moving towards or away from the camera.
• Install the camera within range of the recorder (noted in the
camera’s specifications).
• This camera is weather resistant for outdoor use (IP66 rated).
Installation in a sheltered location is recommended.
• Battery life will vary based on temperature, settings and number of events.
To optimize motion detection:
1.
2.
3.
4.
Launch the Lorex Cirrus app.
Tap a channel in Live View to select it.
, then tap Motion.
Tap
Configure the following as needed:
a
b
c
a. Sensitivity: The amount of motion needed
to trigger recording (e.g., higher sensitivity
d
requires less motion to trigger recording).
b. Area Selection: Not supported.
c. Distance Setting: Configure distance setting for motion detection. While watching
the camera’s video on your mobile device, recreate a motion event in front of your
camera. The icon will change from
to
when motion is detected by the camera.
Change the distance setting if motion detection is being triggered by unwanted
events.
NOTE: Distance will be affected by temperature.
d. Buzzer: Set the recorder to sound an alarm when motion is detected.
STEP 4B: Installing the Cameras
Follow the instructions below to mount the cameras. It is recommended that you refer
to the “Installation Tips” section to help you select good mounting locations.
5.
Tap Save when finished. Repeat for other cameras on the system.
To install your cameras:
Pairing the Camera
1. Set the mounting bracket in the desired mounting position. Mark
holes through the mounting bracket (shown as orange X’s on the
right).
Your cameras should be paired to the recorder and ready to use out of the package. If a
camera becomes unpaired, or if you have purchased a Wire-Free add-on camera
(max. 6 cameras per system), follow the instructions below.
2. Drill holes where marked for the mounting screws using the
included drill bit (item C in toolkit).
To pair cameras using the Lorex Cirrus app:
1. From Live view, tap any free
channel you would like to pair
a camera to (marked with a
icon).
3. Secure the bracket to the mounting surface with
the included mounting screws (×4). Make sure all
screws are fastened tightly using the included
screwdriver (item A+B in toolkit).
NOTES:
• Insert the included drywall anchors if you are mounting the camera
onto drywall.
• The hole at the top of the mounting bracket will be used in step 5,
once the camera is attached to the mounting plate.
LWB4800 / LWB4900 Series
LWB5800 / LWB6800 Series
NOTE: A “pairing successful” message should appear on screen. If you do not see this message,
repeat the steps above.
Charging the Power Pack
Connect the included power adapter to the micro USB port on the
Power Pack.
NOTE: The Power Pack LED flashes red while outside the safe charging
temperature of 32-113°F (0-45°C). In this state, the camera remains
powered up, but the Power Pack will not charge outside the safe
temperature range.
Problem
Mounting
surface
ATTENTION:
This camera includes an Auto Mechanical IR Cut Filter. When the camera changes between Day/Night viewing
modes, an audible clicking noise may be heard from the camera. This clicking is normal, and indicates that the
camera filter is working.
Available Accessories
The following accessories are available for purchase. Visit lorex.com and search for the
model numbers below for details:
WHITE
ACPWF1
LWB4901AC2
LWB6801AC3
LWB6850AC3
ACPWFBK1
BLACK
Green
Red
Meaning
Fully charged
Currently charging
2-cell
Accessory
Power Pack
3-cell Accessory
Power Pack
PLUS
Solar
Panel
ACBATT2
ACBATTR2
ACBATT3
ACBATTR3
ACSOL1B*
* Compatible with select Wire-Free cameras only. Visit lorex.com/compatibility for
details.
Solution
• Ensure the camera is not pointing at a high-traffic area. Position the camera so it
only captures areas of interest with no high-traffic areas (e.g., a busy sidewalk or
roadway) visible in the image.
• Live video is being viewed too frequently. Viewing live video often will impact battery
performance.
• Ensure you have set an active area and distance setting for motion detection to
reduce false alarms. See “Optimizing Motion Detection” for details.
• Battery life will vary based on temperature, settings and number of events.
Picture is dropping
• Move the camera closer to the receiver.
• Try repositioning the camera, receiver, or both to improve the reception.
Picture is or has
become choppy
• Ensure the camera resolution is set to 720p using the Lorex Cirrus app or the DVR.
• Try moving the camera closer to the receiver.
• Remove obstructions between the receiver and camera.
Camera is not
detecting motion
• Your camera may be too far away from the area of interest. Try to keep the camera
within 20ft (6.1m) of the area you want to monitor.
• Review the “Installation Tips” and “Optimizing Motion Detection” sections to ensure
your camera is installed in an optimal location and motion detection is properly
configured.
Picture is too bright
• Ensure your camera isn’t pointed directly at a source of light (e.g., sun or spot light).
• Move your camera to a different location.
Night vision is not
working
• The night vision activates when light levels drop. The area may have too much light.
Picture is not clear
• Check the camera lens for dirt, dust, spiderwebs. Clean the lens with a soft, clean
cloth.
• Too much environmental interference will affect picture clarity. Move the camera to a
different location.
Bright spot in video
when viewing at night
• Night vision reflects when pointing a camera through a window. Move the camera to
a different location.
Arm
rotation
8. Use the included cable clips to complete the installation.
LWB4801AC2
LWB4801AC3
LWB4850AC2
LWB4850AC3
LWB5801AC2
Approx. 8 hours
Battery life is too
short
Arm
angling
Camera
levelling
Power cable
Extra Power
Pack Power
Adapters
3-cell
• Ensure the camera is connected to a compatible DVR. For full camera compatibility,
visit lorex.com/compatibility
• Ensure the wireless receiver is properly connected to the DVR.
• Ensure the Power Pack is properly inserted into the camera base.
• Ensure you have removed the PLEASE REMOVE label from the Power Pack.
• Connect the power adapter to your Power Pack to ensure the Power Pack is charged.
The LED indicator on the power pack glows green for full charge, red for less than full
charge.
• Remove obstructions between the receiver and camera. Materials such as brick,
concrete and wood can significantly impact the wireless signal strength.
• Try repositioning the camera, receiver, or both to improve the reception. The receiver
can be wall mounted using the included double-sided tape or mounting screws.
LWB5800 / LWB6800 Series
NOTE: For LWB5800 / LWB6800 Series cameras, if you are angling the camera
down and to the right, position the antenna as shown to the right.
Wire-Free Add
On Cameras
Approx. 6 hours
No picture / signal
7. Adjust the angle of the camera:
Use the included
Allen Key (item D
in toolkit) to loosen
the adjustment
screws labelled
below. Tighten all
adjustment screws
when finished.
Charge Time
2-cell
Troubleshooting
NOTE: You will need to loosen the locking screw to
remove the Power Pack in the future.
COLOR
Power Pack
LED Color
6. OPTIONAL: Tighten the pre-installed locking screw on the
base of the Power Pack using the included screwdriver
(item A+B in toolkit).
Adjustment
ring
LWB4800 / LWB4900 Series
LWB5800 / LWB6800 Series
5. Insert the security screw
through the fasteners on the
top of the camera base and
mounting bracket to secure
the camera to the mounting
bracket. Tighten using the
included screwdriver (item A+B
in toolkit).
Twist the
adjustment ring
counterclockwise
to reposition the
camera. Tighten
the adjustment
ring when finished.
2. Tap PAIR. A timer for 30
seconds appears.
4. Lower the camera base onto
the mounting bracket so
the 2 tabs in the mounting
bracket lock into the 2 slots
in the camera base.
LWB4800 / LWB4900 Series
3. Press and hold the pair button on the
back of the camera for 3 seconds.
LHB926_LHB927_QCG_EN_R1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising