Lorex | LWF2080B-64 | Quick Reference Guide | Lorex LWF2080B-64 1080p Wire Free Camera System, 4 Battery Powered Black Outdoor Metal Cameras, Ultra-Wide Lens, 65ft Night Vision, Two-Way Audio Speaker-Mic, 1TB Hard Drive Quick Reference Guide

Lorex LWF2080B-64 1080p Wire Free Camera System, 4 Battery Powered Black Outdoor Metal Cameras, Ultra-Wide Lens, 65ft Night Vision, Two-Way Audio Speaker-Mic, 1TB Hard Drive Quick Reference Guide
Lorex Cirrus: Playback
Play back recorded video using the Lorex Cirrus app.
To play back recorded video:
1.
Launch the Lorex Cirrus app.
2.
Tap
3.
Set search options for playback:
, then tap Playback.
c
a. Tap a recorder to reveal available channels.
b. Tap channels to include in search.
c. Tap a date from the calendar to seach for recordings from. Dates with
recordings available are marked with a
red dot.
HD Wire-Free Security System G2
GUIDE
a
b
NOTE: Tap
to filter recordings by
type and resolution.
2/2
4.
Tap Play to begin playback.
Playback Controls:
Quick Reference Guide
LHB926 / LHB927
English Version 1.0
www.lorex.com
Before You Start
You can use playback mode in portrait or landscape mode. Landscape mode
shown below:
Playback
time
Playback
date
Video timeline.
Tap to start
playback from
the selected
time. Pinch or
spread fingers
to change the
time period.
Video
playback
• Upgrade your recorder firmware and mobile app to the latest versions.
• Please note that an upload speed of 3.5Mbps is required for remote
video streaming. Up to 3 devices may connect to the system at the
same time.
• Ensure you have completed initial setup of the Lorex Cirrus app and
the recorder as detailed in the Quick Connection Guide.
Lorex Cirrus: App Overview
Slower
Play / Pause
Faster
Next Frame
Stop
Snapshot
Manual
Mute / Unmute
Recording
Lorex Cirrus: Camera Settings
Configure settings for
selected channel
Main menu
Select channels for
live viewing from all
connected devices
Battery strength
indicator
Channel name
Date and time
stamp
Wireless signal
strength indicator
Change camera settings using the Lorex Cirrus app.
To change camera settings:
1.
2.
3.
4.
Launch the Lorex Cirrus app.
Tap a channel in Live View to select it.
to open settings for the selected Tap
channel.
a
Configure the following as needed:
a. Channel Name: Enter a name of your choice
b
for the channel (e.g., Porch Camera).
Tap to start live view
b. Record Length: Set the recording length
when motion is detected.
c
c. Video Resolution: Set 720p or 1080p
recording.
d
d. Motion Settings: Configure motion
detection settings. See the “Optimizing
Motion Detection” section in the Quick
Connection Guide for details.
e
e. Recording Schedule: Configure the recording
schedule for the selected camera by day. Tap Day to select the day of the week.
Tap squares on the timeline to enable motion recording during specified times
(yellow for enabled, white for disabled). Tap Save when finished.
Split-screen options
Tap to enable the
camera’s intercom;
tap again to stop
Save a snapshot
of the current
live view
Tap to start manual
recording; tap again
to stop
Tap to switch
between muted and
unmuted
Tap to switch to full HD video
quality; tap again for reduced
video quality that is optimized
for streaming
5.
Tap SAVE to save settings.
Lorex Cirrus: Device Settings
Change recorder name and format storage using the Lorex Cirrus app.
To change device settings:
1.
2.
3.
4.
Launch the Lorex Cirrus app.
Tap a channel on the device you want to
edit from Live View.
, then tap Settings.
Tap
Configure the following as needed:
a. Device Name: Enter a name of your
choice for the recorder (e.g., Wire-Free
System).
a
b
b. Format: Tap to select a storage device
(hard drive or microSD card) to format.
Tap Format to confirm the selected
device and begin formatting.
IMPORTANT: Formatting a storage device
will erase all recordings and snapshots.
This step cannot be undone.
NOTE: Only the admin user can format
memory.
5.
Tap Save to save settings.
LHB926_LHB927_QRG_EN_R1
Recorder: Full Setup
Recorder: Quick Menu
The recorder setup detailed in the Quick Connection Guide is a simplified
setup. In order to access features using the recorder, you must complete the
full setup detailed below.
To set up the recorder:
Right-click anywhere on the live viewing screen to open the Quick Menu.
Open the Main Menu.
1. Connect the wireless receiver to
the USB port on the back panel of
the recorder.
Select camera / live display view.
Search for and play back recordings.
NOTE: The receiver includes double-sided tape and
mounting screws for optional wall mounting for
improved line-of-sight with cameras.
Back up video recordings or snapshots
to a USB flash drive (not included).
Recorder: Using the Mouse
2. Connect the recorder to your
router using the included
Ethernet cable.
1. LEFT-CLICK:
• During split-screen display mode: Double-click an
individual channel to view it in full-screen. Double-click
again to return to the split-screen display mode.
• While navigating menus: Click to open a menu option.
1
2. RIGHT-CLICK:
3. Connect the included mouse to
the USB port on the front panel
of the recorder.
• During live view: Right-click anywhere on the screen
to open the Quick Menu.
2
3
• While navigating menus: Right-click to exit menus.
3. SCROLL WHEEL:
• While navigating menus: Scroll to move up / down
through the menu content.
4. Connect a monitor (not included)
to the HDMI or VGA port of the
recorder (HDMI cable included;
VGA cable not included).
HDMI
OR
NOTE: In live view, hover the mouse cursor over the top of the screen to
open the Navigation Bar. Move the mouse cursor away from the top of the
screen to close the Navigation Bar.
VGA*
Recorder: Search and Playback
Search for and play back video recordings on the recorder.
To play back recorded video:
5. Connect the included power
adapter to the recorder. Wait a few
minutes for the system to start
up.
Recorder: Initial Setup Wizard
1.
From live view, right-click and then click Playback.
2.
Log in using the system user name (default: admin) and your new, secure
password you recorded on the Quick Connection Guide.
3.
Use the calendar on the left-side of the screen to select the date to playback.
4.
Check off the channels you would like to search for recordings from on the leftside of the screen.
5.
Click
6.
Search results appear as thumbnails. Double-click any recording to begin video
playback.
For users who wish to use the recorder interface rather than connecting to
the system using the Lorex Cirrus app, you will have to complete the recorder
Setup Wizard to confirm the correct date and time for the system.
NOTE: If you did not use the Lorex Cirrus app for initial setup, you will be
prompted to enter the default username (admin) and password (00000000),
and then create a new password for the recorder.
To complete the setup wizard:
1.
2.
Log in using the system user name (default: admin) and your new, secure
password you recorded on the Quick Connection Guide.
The Setup Wizard launches. Click Next to begin.
to search for recordings.
Select
the day to
playback
Double-click
any event
to begin
playback
Select
channels to
playback
Click to
search for
recordings
Recorder: Backup
Back up video recordings to a USB flash drive (not included).
To back up recorded video:
1.
3.
4.
5.
Click the arrow keys to select a
language for the on-screen display. Click Next
to confirm.
NOTE: It is recommended to format USB flash drives prior to using them with your
wire-free system.
2.
From live view, right-click and then click Backup.
3.
Log in using the system user name (default: admin) and your new, secure password
you recorded on the Quick Connection Guide.
4.
Configure the following:
a. Date: Enter the date to search
for recordings from.
Click the arrow keys to select your region. Click
Next to confirm.
c. Channel / Type: Select the
channel and recording type
to search for, or select All
to browse all channels and
recording types.
Click to select the correct date
from the calendar.
6.
Review the information you have set for the recorder. Click Accept to confirm.
b
d
c
e
d. Search / Quick Backup: Click
Search to show all recordings
that fit your search criteria, or
click Quick Backup to back up
all recordings that fit the search criteria.
Select the correct time zone from
the dropdown.
Click Next to confirm.
a
b. Time: Enter a start and end
time for your search.
Enter the date and time:
Select a time format from the
dropdown. For 12Hour format,
select either AM or PM from the
second dropdown.
Insert a USB flash drive (not included) into one of the USB ports marked Mouse /
Backup on the back of the recorder.
e.
(Not applicable for Quick Backup) Recordings that fit the search are shown on
screen. Check recordings you want to back up, then click Backup.
5.
The Backup Type screen appears. Select a filetype for your backup files, then
click Save.
6.
The USB flash drive contents are shown on screen. Navigate to the location you
want to save the backup files in, then click OK to begin the back up. Progress is
shown on screen.
NOTE: Do not disconnect the USB flash drive until the backup is complete.
LHB926_LHB927_QRG_EN_R1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising