Lorex | LHV514K86 | Quick Start Guide | Lorex LHV514K86 4K Ultra HD 8 Channel Security System Quick Start Guide

Lorex LHV514K86 4K Ultra HD 8 Channel Security System Quick Start Guide
Package Contents
•
•
•
•
Troubleshooting
4K Ultra HD Active Deterrence Security Camera
Mounting Kit*
BNC / Power Extension Cable*
Power Adapter**
Problem
No picture / signal
* Per camera in multi-camera packs.
** A multi-camera power adapter that provides power to multiple
cameras or individual power adapters may be provided depending on
product configuration.
ATTENTION:
A REGULATED UL / CSA APPROVED power supply is REQUIRED for use with
this camera (included). Only the included power adapter can be used. Use of
a non-regulated, non-conforming power supply can damage this product and
voids the warranty.
Safety Precautions
• Read this guide carefully and keep it for future reference.
• Follow all instructions for safe use of the product and handle with care.
• Use the camera within given temperature, humidity and voltage levels noted in
the camera’s specifications.
• Do not disassemble the camera.
• Do not point the camera directly towards the sun or a source of
intense light.
• Use only the supplied regulated power supply provided with the product. Use of
a non-regulated, non-conforming power supply can damage the product and void
the warranty.
• Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh,
chemical-based cleaners.
• The supplied cable is rated for surface and in-wall mounting only. Cables for
floor-to-floor installations are sold separately (CMR type). These and other cables
are available at lorex.com.
Changing the DVR
4K Resolution
Connecting
the to
Cameras
The output resolution of a Lorex HD DVR is set to 1080p as a default. To view 4K
resolution on a 4K monitor, the output resolution must be changed using the DVR
menu.
To change the output resolution through a Lorex HD DVR:
Click Main Menu and then click the Setting icon (
Click Setting > Display.
Click the Display tab.
In the Resolution drop-down menu, select 3840 x 2160.
Click Apply to save and click OK to exit.
• Ensure your camera isn’t pointed directly at a
source of light (e.g., sun or spot light).
• Check the brightness settings of the DVR and
monitor.
• Move your camera to a different location.
Picture is too dark
• Check the brightness and contrast settings of the
DVR and monitor.
Night vision is not working
• Only use the approved power supply and 4K
extension cables provided with camera.
• The night vision activates when light levels drop.
The area may have too much light.
Picture is not clear
• Only use the approved power supply and 4K
extension cables provided with camera.
• Check the camera lens for dirt, dust, spiderwebs.
Clean the lens with a soft, clean cloth.
• Make sure that the cable run is within the
limitations specified in the section ‘Cable Extension
Options’.
Bright spot in video when
viewing camera at night
• Night vision reflects when pointing a camera
through a window. Move the camera to a different
location.
The camera warning
light is not switching on
automatically
• Ensure that you have enabled and configured white
light deterrence using a compatible DVR. See your
DVR’s documentation for more information.
• Ensure the active areas and schedule for white
light deterrence are set properly. The default
schedule for the warning light is night times
(between 5PM and 7AM).
The camera siren is not
switching on automatically
• The camera siren cannot switch on automatically.
You can control the camera siren manually using
the Lorex Cloud app or a compatible DVR.
).
Installation Tips
• Point the camera where there is the least amount of obstructions
(i.e., tree branches).
• Install the camera where vandals cannot easily reach.
• Secure cabling so that it is not exposed or easily cut.
• This camera is rated for outdoor use. Installation in a sheltered location is
recommended.
Disclaimers
• Only use the approved power supply and 4K
extension cables provided with camera.
• Ensure that you have set the DVR to 4K output
resolution. See ‘Changing DVR to 4K Resolution’
for details.
• The cameras are only compatible with certain Lorex
HD DVRs. For the full list of compatible recorders,
visit lorex.com/compatibility.
• Ensure your TV or monitor is on the correct input
channel. Common terms for input channels: INPUT,
AV CHANNEL, LINE1, LINE2, AUX.
• Ensure your DVR is properly connected to your TV
or monitor.
• Ensure connections are properly connected.
• Ensure the camera power supply is plugged in.
• Ensure that you only use the included power cable.
Picture is too bright
1. Right-click on the Live View to access the Quick Menu.
2.
3.
4.
5.
6.
Solution
4K Ultra HD Active Deterrence
Security Camera
Quick Start Guide
English Version 3.0
Dimensions
3.2” / 80mm
5.9” / 150mm
2.8”
71mm
• For a full list of compatible recorders, visit lorex.com/compatibility.
• Not intended for submersion in water. Installation in a sheltered location
recommended.
• This camera includes an Auto Mechanical IR Cut Filter. When the camera changes
between Day/Night viewing modes, an audible clicking noise may be heard from
the camera. This clicking is normal, and indicates that the camera filter is working.
LBV8541X / LBV8543X SERIES
Copyright © 2019 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right
to modify product design, specifications and prices, without notice and without
incurring any obligation. E&OE. All rights reserved.
LBV8541X_LBV8543X_QSG_EN_R3
www.lorex.com
Male Power
ATTENTION:
Test your camera prior to selecting a permanent mounting location by
temporarily connecting the camera and cable to your DVR.
Before Installing the Camera
Female Power
This camera can only be used with 4K rated extension
cables. For details, see ‘Cable Extension Options’.
• Decide whether to run the cables
through the wall / ceiling (drilling
required) or along the wall / ceiling.
• If you run the cables along the
wall / ceiling, you must run the
cable through the cable notch on the
base. This will keep the camera base
flush to the surface when mounted.
Activating Deterrence
Connecting the Camera
Installing the Camera
Camera
DVR
Connect the BNC connector
to a video input on your DVR.
Cable Notch
To install your camera:
1. Set the camera in the desired mounting position and mark
holes for screws through the camera base.
2. Drill the holes, then feed the cable through the mounting
surface or cable notch.
NOTE: Insert the included drywall anchors if you are
mounting the camera onto drywall.
3. Mount the camera stand to the mounting surface using
the provided screws. Make sure all screws are fastened
tightly.
4. Adjust the camera as shown below:
Connect the female power
head to the included power
adapter.
Connect the male power head
and the BNC connector to the
camera.
Power
Connecting
Adapter
the Types
Cameras
A multi-camera power adapter that provides power to multiple cameras
or individual power adapters may be provided, depending on product
configuration.
Individual Power Adapter*
Multi-Camera Power Adapter*
* Only the included power adapter can be used. Images for representation only.
The camera’s deterrence features deter suspicious activities
from occurring by flashing a warning light and/or sounding a
siren from the camera. You can manually control these features
using the Lorex Cloud app.
NOTES:
• See your DVR’s documentation for more information about
enabling and automating deterrence features using a
compatible DVR.
• For a full list of compatible recorders, visit
lorex.com/compatibility.
REQUIREMENTS:
• Connect the camera to a compatible DVR. See ‘Connecting
the Camera’ section for more information.
• Ensure the compatible DVR is set up remotely via the
Lorex Cloud app. See your DVR’s documentation for more
information.
To activate deterrence manually through the Lorex Cloud app:
1. From live view, double-tap the deterrence camera to open
the channel in full screen.
2. Tap the deterrence icons on the camera display to switch
on/off the following deterrence features:
• Tap the icon to switch on ( ) / off ( ) the camera warning
light.
• Tap the icon to switch on ( ) / off ( ) the camera siren.
NOTE: The camera warning light / siren will automatically
switch off after 10 seconds.
Resources
Need Help?
Connecting
Setup Diagram
the Cameras
BNC Video
Extension Cable
Camera
Visit us online for up-to-date software and
complete instruction manuals
12V DC Power
HD DVR
B
C
A
A. ROTATING THE ARM: Loosen the adjustment ring by turning it
counter-clockwise. Rotate the arm of the camera up to 360°, then
tighten the adjustment ring against the base.
B. BENDING THE ARM: Use a Phillips head screwdriver (not included)
to loosen the adjustment screw closest to the camera base. Bend the
arm of the camera up to 90°, then tighten the screw.
C. LEVELING THE CAMERA: Use the screwdriver to loosen the
adjustment screw furthest from the camera base. Rotate the camera
until it is level with the viewing area, then tighten the screw.
5. Remove the vinyl film from the camera lens when your
installation is complete.
Power Adapter
Cable Extension Options
Extend the cable run for your camera depending on the cable type used. Additional
extension cables sold separately. See table below:
Option
Model Number
Cable Length
1
CB120URB1A
120ft (37m)
2
CB250URB1A
250ft (76m)
Notes:
1. The extension cable must be a single stretch of cable between the DVR and
camera. You cannot connect multiple extension cables to each other.
2. Indicators that your cable run may be too long:
• Camera loses video when switching to night vision.
• Video is permanently black & white (even during day time).
• Video is unclear, soft, or distorted.
3. For more information on extension cables, visit lorex.com.
1
Visit lorex.com
2
Search for the model number
of your product
3
Click on your product in the
search results
4
Click on the Downloads tab
LBV8541X_LBV8543X_QSG_EN_R3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising