Lorex | 4KHDIP822NWW | Quick Start Guide | Lorex 4KHDIP844NVW 4K Ultra HD IP NVR System, 4 Outdoor 4K (8MP) IP Bullet and 4 4K Audio Dome Cameras, Quick Start Guide

Lorex 4KHDIP844NVW 4K Ultra HD IP NVR System, 4 Outdoor 4K (8MP) IP Bullet and 4 4K Audio Dome Cameras, Quick Start Guide
Audio Settings
Package Contents
•
•
•
•
4K Motorized Varifocal HD IP Dome Security Camera
Mounting Kit*
Mounting Template*
CAT5e Ethernet Extension Cable with Pre-attached
RJ45 Cable Gland*
• Allen Key*
* Per camera in multi-camera packs.
ATTENTION:
It is recommended to connect the camera to the NVR or an external PoE switch. If
using a DC power adapter (not included) with the camera, a REGULATED power supply
is REQUIRED for use with this camera. Use of a non-regulated, non-conforming power
supply can damage this product and voids the warranty.
Cable Extension Options
Extend the cable run for your camera. Additional extension cables sold
separately. See table below:
Cable Type
Max Cable Run
Distance
Max # of
Extensions
CAT5e (or higher) Ethernet cable
300ft (92m)
3
• You can use a RJ45 coupler or switch (not included) to connect male
ends of Ethernet cable together.
• To extend the cable run beyond 300ft (92m), a switch will be required
(sold separately).
ATTENTION:
Audio recording without consent is illegal in certain jurisdictions. Lorex
Corporation assumes no liability for use of its products that does not
conform with local laws.
Audio is disabled by default. To enable camera audio through a Lorex HD NVR:
1. In Live View, right-click anywhere on the screen to open the Quick Menu.
2. Click Main Menu. If prompted, enter the system user name and password.
3. Click
and select Recording > Recording.
4. Configure the following:
A. Under Channel, select the channel
that the audio-enabled camera is
A
B
connected to.
B. Under Type, select Continuous.
C. Check the check box to enable audio
for Main Stream.
C
D
E
D. You can also enable audio for Sub
Stream. Check the check box to enable
audio for Sub Stream.
E. Video must be enabled for Sub
F
Stream to enable/disable audio.
F. Click Apply to save your changes.
NOTE: You must enable audio for all recording types under the Type dropdown.
Repeat the above steps to enable camera audio for all recording types.
4.8” / 122mm
4.8” /
122mm
4.1” /
105mm
Disclaimers
Using the RJ45 Cable Gland (Optional)
The RJ45 cable gland covers the camera’s Ethernet connector and the RJ45 plug to
provide weather-resistance and protection from dust, dirt and other environmental
contaminants.
Installation Tips
The RJ45 cable gland is pre-attached to the
included CAT5e ethernet extension cable.
RJ45 Cable Gland
To use the RJ45 cable gland:
Twist the RJ45 cable gland barrel securely onto the camera Ethernet connector.
English Version 1.0
Dimensions
• For a full list of compatible recorders, visit lorex.com/compatibility
• Not intended for submersion in water. Installation in a sheltered
location recommended.
• This camera includes an Auto Mechanical IR Cut Filter. When the
camera changes between Day/Night viewing modes, an audible clicking
noise may be heard from the camera. This clicking is normal, and
indicates that the camera filter is working.
CAT5e
Ethernet
Extension
Cable
Quick Start Guide
5. Click OK.
NOTE: These instructions are based on current Lorex HD NVR interface. For more
information, see your NVR’s instruction manual on lorex.com.
Safety Precautions
• Read this guide carefully and keep it for future reference.
• Follow all instructions for safe use of the product and handle with care.
• Use the camera within given temperature, humidity and voltage levels
noted in the camera’s specifications.
• Do not disassemble the camera.
• Do not point the camera directly towards the sun or a source of
intense light.
• Use only the supplied regulated power supply provided with the
product. Use of a non-regulated, non-conforming power supply can
damage the product and void the warranty.
• Periodic cleaning may be required. Use a damp cloth only. Do not use
any harsh, chemical-based cleaners.
• The supplied cable is rated for surface mounting only. Cables for in-wall
and floor-to-floor installations are sold separately (CMR type). These
and other cables are available at lorex.com
4K Motorized Varifocal HD IP Dome
Security Camera with Audio
• Point the camera where there is the least amount of obstructions
(i.e., tree branches).
• Install the camera where vandals cannot easily reach.
• Secure cabling so that it is not exposed or easily cut.
• This camera is rated for outdoor use. Installation in a sheltered
location is recommended.
LNE8964A / LNE8974A SERIES
RJ45 Cable
Gland Barrel
Camera Ethernet
Connector
NOTE: The RJ45 cable gland is weather-resistant. Seal the cap with silicone and/or
electrical tape for additional sealing if it will be exposed to precipitation regularly.
Copyright © 2018 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right
to modify product design, specifications and prices, without notice and without
incurring any obligation. E&OE. All rights reserved.
LNE8964_LNE8974_QSG_EN_R1
www.lorex.com
Adjusting Zoom and Focus
Connecting the Camera
Installing the Camera
Adjust the camera’s zoom and focus using a compatible NVR.
For more information, see your NVR’s instruction manual on
lorex.com.
Right-click on the
camera’s live view
and then click
AutoFocus. Use the
sliders to adjust zoom and focus.
ATTENTION:
Test your camera prior to selecting a permanent mounting location by temporarily
connecting the camera and cable to your NVR.
Before Installing the Camera
Ethernet Cable
• Decide whether to run the cables through the wall /
ceiling (drilling required) or along the wall / ceiling.
• If you run the cables along the wall / ceiling, you must
run the cable through the cable notch on the base. This
will keep the camera base flush to the surface when
mounted.
To install your camera:
Cable
Notch
Camera
NVR
Connect the other end of the
Ethernet cable to the NVR’s PoE
ports. The camera may take a
minute to power up after
being connected.
Mounting
Surface
Camera Base
Drywall Anchors
Mounting
Screws
Ball Camera
Dome Cover
Screw
Dome Cover
1. Use the included Allen key to loosen the screw on the dome
cover. Do not loosen all the way.
2. Separate the camera base, ball camera, and dome cover.
3. Use the included mounting template to mark holes for the
mounting screws and camera cable.
4. Drill holes for the mounting screws and camera cable.
5. Feed the camera cable through the camera base. If you are
running the cables against a wall or ceiling, make sure to
pass the cable through the cable notch as shown above.
6. Connect the cables as shown in the section ‘Connecting the
Camera’.
7. Mount the camera base to the mounting surface using the
included screws and optional drywall anchors.
8. Place the dome cover over the ball camera.
9. To attach the dome cover to the camera base:
Dome Cover
Problem
• Ensure the camera is connected to a compatible NVR. For full
camera compatibility, visit lorex.com/compatibility.
• The camera may take up to 1 minute to power up after being
connected to the NVR. Wait two minutes before following the
steps below.
• Ensure the camera is connected to your NVR or to your local
network.
• If you are not using PoE, you must connect the camera to a
12V DC power adapter (not included).
• If the camera is connected to the LAN, you must search your
network for cameras using the NVR. See the NVR’s instruction
manual.
• Ensure your NVR is properly connected to a TV/monitor.
• There may be an issue with your extension cable run. Connect
the camera to the NVR using a different Ethernet cable.
Picture is too bright
• Ensure your camera isn’t pointed directly at a source of light
(e.g., sun or spot light).
• Move your camera to a different location.
• Check the brightness and contrast settings on the NVR.
Picture is too dark
• Check the brightness and contrast settings on the NVR.
Night vision is not
working
• The night vision activates when light levels drop. The area may
have too much light.
Picture is not clear
• Check the camera lens for dirt, dust, spiderwebs. Clean the
lens with a soft, clean cloth.
• Make sure that the cable run is within the limitations specified
in the section ‘Cable Extension Options’.
Bright spot in video
when viewing camera
at night
• Night vision reflects when pointing a camera through a
window. Move the camera to a different location.
Picture is in color in
dark conditions
• This camera comes with an image sensor that is extra
sensitive to light, meaning that the camera stays in color
mode at low-light conditions. For instructions on how to make
your camera switch to night mode, visit lorex.com, and search
for “How do I make my camera switch to night mode?”
No audio
• Audio is only supported on Lorex HD NVRs. For a list of
compatible recorders, visit lorex.com/compatibility.
• Ensure NVR volume is turned on / turned up.
• Ensure audio function on camera is turned on (see ‘Audio
Settings’).
• Ensure audio is turned up on viewing device.
OR
Connect the Ethernet cable to
the camera.
NOTES:
• For weatherproofing instructions,
see “Using the RJ45 Cable Gland
(Optional)”.
• A 12V DC power adapter (model#:
ACCPWR12V2A, not included) is
only required if connecting the
camera’s Ethernet cable to a
router or switch that does not
support PoE.
Connect the other end of the
Ethernet cable to a router or
switch on your network. See
your NVR manual for details on
connecting the camera to your
NVR using a switch or router.
Connecting
Setup Diagram
the Cameras
Scenario 1: Connect Cameras to NVR
Router
HD NVR
Camera
Scenario 2: Connect Cameras to Local Area Network (LAN)
Router
Camera Base
Solution
No picture / signal
(Optional)
12V DC Power
A. Angle the dome cover as shown below.
B. Align the protruding metal tab inside the dome cover with the
indent on the camera base.
C. Attach the dome cover onto the camera base. Ensure that the
dome cover lays flat against the camera base.
C
Troubleshooting
HD NVR
Camera
Need Help?
Visit us online for up-to-date software and
complete instruction manuals
Camera Base
Indent
B
Metal Tab
10. Use the included Allen key to tighten the dome cover screw
halfway onto the camera base. Do not tighten all the way.
11. Move the ball camera to the desired position. Tighten the
dome cover screw all the way.
PoE Switch
ATTENTION:
This camera is only compatible with select NVRs. For a list of compatible
recorders, visit lorex.com/compatibility.
LNE8964_LNE8974_QSG_EN_R1
1
Visit lorex.com
2
Search for the model number of your product
3
Click on your product in the search results
4
Click on the Downloads tab
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising