Montigo | PVHEX 58/510-300 Wall Power Vent System | Instruction | Montigo PVHEX 58/510-300 Wall Power Vent System Instruction

Montigo PVHEX 58/510-300 Wall Power Vent System Instruction
Installation & Maintenance Manual
PVHEX58-300 & PVHEX510-300
5/8 and 5/10 External Wall
Power Vent
•
The installation of this fireplace must be done by a
qualified and certified gas appliance installer.
•
Check local codes and read all instructions prior to
installation.
®
C
US
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury,
death, or property damage.
NOTICE
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.
— Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
•
Do not try to light any appliance.
•
Do not touch any electrical switch; do not use any
phone in your building.
•
Leave the building immediately.
•
Immediately call your gas supplier from a neighbour's
phone. Follow the gas supplier’s instructions.
•
If you cannot reach your gas supplier, call the fire
department.
— Installation and service must be performed by a qualified
installer, service agency or the gas fitter.
WARNING
Do not store or use gasoline or any other flammable vapours or
liquids in the vicinity of this or any other gas burning appliance. A fire
or explosion may occur resulting in serious injury, property damage
or death
Installation and service must be performed by a qualified installer,
service agency or the gas fitter.
NOTICE
This power vent is approved for use with Montigo fireplaces only and
is certified to ANSI Z21.50 / CSA 2.22 vented gas fireplace standard
along with the fireplace
WARNING
Some materials used in the manufacturing process of this product can
expose you to Benzene which is known in the State of California to
cause cancer and birth defects or other reproductive harm. For more
information go to www.P65warnings.ca.gov
XG0517
General
Safety Alert Key
General Information
This installation guide covers installation of the External Power
Vent System only. This system is designed to allow installation of
gas fireplaces that cannot be done with a standard Direct Vent gas
fireplace installation. Only for use on R-Series, R-Series See-Through
and RP-Series.
ONLY USE WITH APPROVED FIREPLACES - see fireplace installation
manual.
Read through the fireplace's installation & maintenance manual,
as it must also be adhered to.
Power Cord Harnesses:
CAUTION
When cold air enters the warmer building interior, primarily at the air
intake end, condensation may occur on the exterior of the flex pipe.
To limit this condensation, install insulation over the last 20' of flex
pipe. Also, by sloping the last 20'-0' of flex pipe downwards towards
the exterior of the building will help eliminate any condensation
problems, should they occur. Ensure the termination is securely
fastened and sealed to the flex pipe. Fasten the termination to the
exterior of the building with water tight sealant and the appropriate
fasteners.
EPVH10 - 10 foot power cord and harness
EPVH20 - 20 foot power cord and harness
NOTICE
EPVH30 - 30 foot power cord and harness
EPVH40 - 40 foot power cord and harness
EPVH50 - 50 foot power cord and harness
EPVH60 - 60 foot power cord and harness
You must read and understand this manual prior to installation,
operation or troubleshooting the appliance. Please retain this owner's
manual for future reference and maintenance.
EPVH70 - 70 foot power cord and harness
EPVH80 - 80 foot power cord and harness
EPVH90 - 90 foot power cord and harness
Specifications
2
Power
Speed
Maximum
Airflow
Pipe Dimensions
EPVH100 -100 foot power cord and harness
PVHEX58-300
5"/8"
300
CFM
2700 RPM
Connect to
fireplace
control
box
PVHEX510-300
5"/10"
300
CFM
2700 RPM
Connect to
fireplace
control
box
XG0517
General
Contents
Safety Alert Key���������������������������������������������������������������������������������� 2
General Information�������������������������������������������������������������������������� 2
Specifications������������������������������������������������������������������������������������� 2
Product Dimensions�������������������������������������������������������������������������� 4
Unit Dimensions..............................................................................................4
Installation Locations������������������������������������������������������������������������ 5
Install��������������������������������������������������������������������������������������������������� 6
Installing the Power vent...............................................................................6
Installing the Power vent...............................................................................6
Wiring Diagram................................................................................................8
Wiring Installation............................................................................................8
Capacitor Replacement..................................................................................8
Motor and Capacitor Replacement...........................................................10
Appendix B: Warranty��������������������������������������������������������������������� 12
XG0517
3
PVHEX58-300 External Horizontal Power Vent
13"
330
1
"
2
114
4
PVHEX58-300 External Horizontal P
General
2"
51
1
"
8
156
6
9 "
2
Product Dimensions
8"
241
1
5"
127
203
7
"
8
505
19
Unit Dimensions
1
4 "
2
114
13"
330
8"
203
1
"
4
566
22
13"
330
1
"
2
114
2"
51
4
1
"
8
156
6
1
"
4
465
18
1
"
4
439
17
1
"
2
241
7
"
8
403
15
13"
330
13"
330
1
"
4
541
2"
51
1
"
8
156
9
21
5"
127
6
7
"
8
505
19
1
"
2
241
9
Front View
7
"
8
505
19
1
22 "
4
566
Top View
1
"
4
566
22
1
"
4
465
1
"
4
439
18
17
7
"
8
403
15
13"
330
13"
330
1
"
4
465
1
"
4
439
18
PVHEX58-300
8"
203
PVHEX10-300
10"
254
1 5"
"
4
127
541
21
Rear View
17
7
"
8
403
15
13"
330
Side View
Power Head
Framing Kit
1
21 "
4
541
Electrical Box
Vent Retainer
Figure 1. PVHEX58-300 & PVHEX510-300 (Tolerance ± ⅛") [mm]
1
"
2
368
14
4
Framing
XG0517
Installation
Installation Locations
PVHEX58-300
E
INSID ETAIL
ER D
N
R
O
C
G
v
H
A
D
E
V
B
FIXED
ED
CLOS
v
V
L
F
B
B
C
ABLE
OPER
v
ABLE
OPER
v
FIXED
ED
CLOS
A
I
M
X
v
X
v
B
v
K
J
B
V VENTER TERMINAL
Canadian Installations
X AIR SUPPLY INLET
1
US Installations
2
A= Clearance above grade, veranda,
porch, deck, or balcony
12 in (30 cm)
12 in (30 cm)
B= Clearance to window or door that
may be opened
6 in (15 cm) for appliances <
10,000 Btuh (3 kW), 12 in
(30 cm) for appliances >
10,000 Btuh (3 kW) and <
100,000 Btuh (30 kW), 36 in
(91 cm) for appliances >
100,000 Btuh (30 kW)
6 in (15 cm) for appliances <
10,000 Btuh (3 kW), 9 in
(23 cm) for appliances >
10,000 Btuh (3 kW) and <
50,000 Btuh (15 kW), 12 in
(30 cm) for appliances >
50,000 Btuh (15 kW)
C= Clearance to permently closed
window
D= Vertical clearance to ventilated
soffit located above the terminal within
a horizontal distance of 2 feet (61 cm)
from the center line of the terminal
E= Clearance to unventilated soffit
B
B
15 in (38 cm)
15 in (38 cm)
15 in (38 cm)
6 in (15 cm)
15 in (38 cm)
15 in (38 cm)
6 in (15 cm)
15 in (38cm)
H= Clearance to each side of center
line extended above meter/regulator
assembly
3 ft (91 cm) within a height 15
ft. (4.5 m) above the meter/
regulator assembly
*
I= Clearance to service regulator
vent outlet
3 ft (91 cm)
F= Clearance to outside corner
G= Clearance to inside corner
XG0517
AREA WHERE TERMINAL IS
NOT PERMITTED
Canadian Installations
1
US Installations
2
J= Clearance to nonmechanical air
supply inlet to building or the
combustion air inlet to any other
appliance
6in (15 cm) for appliances <
10,000 Btuh (3 kW), 12 in (30
cm) for appliances > 10,000
Btuh (3 kW) and < 100,000
Btuh (30 kW), 36 in (91 cm)
for appliances > 100,000
Btuh (30 kW)
6in (15 cm) for appliances <
10,000 Btuh (3 kW), 9 in (23
cm) for appliances > 10,000
Btuh (3 kW) and < 50,000
Btuh (15 kW), 12 in (30 cm)
for appliances > 50,000 Btuh
(15 kW)
K= Clearance to a mechanical air
supply inlet
6 ft (1.83 m)
3 ft (91 cm) above if within 10
ft (3 m) horizontally
7 ft (2.13 m)
L= Clearance above paved sidewalk
*
or paved driveway located on
public property
M= Clearance under veranda porch
12 in (30 cm)
*
deck, or balcony
1 In accordance with the current CSA B149.1, Natural Gas and Propane Installation Code
2 In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code
A vent shall not terminate directly above a sidewalk or paved driveway that is located between two
single family dwellings and serves both dwellings.
Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath
the floor.
* For clearances not specified in ANSI Z223.1/NFPA or CSA B149.1, one of the following shall be
indicated
a) A minimum clearance value determined by testing in accordance with section 2.23.5, or;
b) A reference to the following footnote:
"Clearance in accordance with local installation codes and the requirements of the gas supplier"
*
5
Installation
Install
Installing the Power vent
2. Remove Power head from rough in box.
1
"
2
368
14
Framing
Figure 2.d
1
"
4
389
3. Screw rough in box to wall.
15
Wall board
Rough in box
Figure 2. Framing dimensions (combustible material construction)
Installing the Power vent
1. Unscrew Power Head from rough in Box by unscrewing four
screws.
Figure 2.e
4. Remove six screws securing the electrical cover. Remove cover
Figure 2.f
5. Remove two screws on the strain relief plate. Remove plate
Figure 2.b Unscrewing four screws
Figure 2.g
Figure 2.c
6
XG0517
Installation
6. Take the electrical harness (EPVH-10-100) that will
communicate with the Power vent and pass the cable through
the slot in the rough box. Make sure the nut for the strain
relief is inside the box and the strain relief is outside the box.
10. Pass the vent pipe through the rough in box so it extends 6
1/2 inches into the rough in box.
Figure 2.l
Figure 2.h
7. Reinstall the strain relief plate underneath the strain relief
nut and screw the strain relief plate down. Then tighten strain
relief nut.
11. Slip the Vent Support Band over the vent so that it sits flush
against the back of the rough in box. Tighten the band around
the vent so the vent cannot be pushed back through the hole
in the rough in box.
Figure 2.m
Figure 2.i
8. Push the molex connector through the hole in the electrical
cover until it clicks into place.
12. Plug the power cable from the power vent head into the
control cable.
Figure 2.n
Figure 2.j
9. Secure the electrical cover back down with the six screws
making sure the control cable curls up safely.
13. Secure power head onto the rough in box with the supplied
4 screws. Make sure the power head makes good contact with
the gasket on the top and sides of the rough in box.
NOTE:
Make sure the power cable
for the power head does
not get pinched or caught.
Exhaust chute is pointed
towards the ground.
Figure 2.k
Figure 2.o
XG0517
7
Operation
Wiring Diagram
Capacitor Replacement
1. Turn off power and gas.
BLUE
GREEN
BLACK
WHITE
6 PIN MOLEX
CONNECTOR
C
KEY WAY
Power Vent Wiring
BROWN
BLACK
Figure 3.a
2. Remove 8 screws securing the outer cover of the power head.
8 fasteners (4 oposite side)
Outer Cover
Figure 3.b
3. Cut 3 zap straps securing wiring.
Wiring Installation
Figure 3.c
Conduit & Wiring clearances
Connect the power vent harness as outlined. Connect the wiring to
the fireplace as outlined in the schematic shown in figure 4. Ensure
that the proper clearances are maintained for the wiring and conduit.
When installing the wiring it must never run above the vent run
and it must be at least 1" clear of all venting.
4. Cut Brown Wire From Motor.
Wire
1” Clearance
8
Figure 3.d
XG0517
Operation
5. Cut white wire from power cable, black wire from motor, and
black wire from capacitor.
9. Using the small bell connector, connect the brown wire from
the motor to the black wire from the capacitor.
Figure 3.h
Figure 3.e
6. Remove ground screw that secures the ground wire and
capacitor bracket to the motor. Note: Keep this screw for later
use. Dispose of old capacitor.
10. Using three supplied zap straps, neatly secure wiring. Make
sure no wires can get caught in the motor or pinched.
Figure 3.i
Figure 3.f
11. Check operation and rotation. Motor should spin counter
clockwise.
7. Strip all the wires for connection. Using old ground screw
secure the ground wire and new capacitor to the motor.
8. Using the large bell connector, connect the white fiber wire
from the power cable to the black wire from the motor and the
black wire from the capacitor.
Figure 3.j
12. Secure outer cover with supplied 8 screws.
Figure 3.g
8 fasteners (4 oposite side)
Outer Cover
Figure 3.k
XG0517
9
Operation
Motor and Capacitor Replacement
5. Cut white wire from power cable, black wire from motor, and
black wire from capacitor.
1. Turn off power and gas.
Figure 4.e
Figure 4.a
2. Remove 8 screws securing the outer cover of the power head.
8 fasteners (4 oposite side)
Outer Cover
Figure 4.b
3. Cut 3 zap straps securing wiring.
Figure 4.c
4. Cut Brown Wire From Motor.
Figure 4.d
10
6. Cut the black fiber wire from power cable.
Figure 4.f
7. Remove eight screws securing the motor plate to power head.
Figure 4.g
8. Lift motor assembly out. Put new motor assembly in.
Figure 4.h
XG0517
Operation
9. Secure motor plate with supplied eight screws.
13. Using the other supplied small bell connector, connect
the brown wire from the motor to the black wire from the
capacitor.
Figure 4.i
10. Attach new capacitor and the ground wire to the ground on
the motor. Strip all the wire ends.
Figure 4.m
14. Using three supplied zap straps, neatly secure wiring. Make
sure no wires can get caught in the motor or pinched.
Figure 4.j
11. Using a supplied small bell connector, connect the black wire
from the power cable to the blue wire from the motor.
Figure 4.n
15. Check operation and rotation. Motor should spin counter
clockwise
Figure 4.k
12. Using the supplied large bell connector, connect the white
fiber wire from the power cable to the black wire from the
motor and the black wire from the capacitor.
Figure 4.o
16. Secure outer cover with supplied eight screws.
8 fasteners (4 oposite side)
Outer Cover
Figure 4.l
XG0517
Figure 4.p
11
Appendix
Appendix B: Warranty
MONTIGO RESIDENTIAL WARRANTY PROGRAM
Canadian Heating Products Inc. and/or Montigo DelRay Corp
(collectively referred to herein as "The Companies"), warrants the
Montigo gas appliance (referred to herein as 'the appliance') to
be free from defects in materials and workmanship at the time
of manufacture. The gas appliance and related components are
further subject to the terms and conditions set forth below.
This warranty covers the following Montigo product series:
Distinction, H, I, L, Linear P and PL, R and Mahana
Component
Coverage Period
Labor Coverage
Firebox, heat exchanger
15 years
1 year
Main burner
15 years
1 year
Gas control valve and related control components
(pilot assembly, spark electrode flame sensors,
thermopile)
1 year
1 year
Electrical components (internal blowers, ignition
control module, wiring, switches, remote control
systems, blower control module, accent bulbs)
1 year
1 year
Firebox media (logset, glass beads, river rocks)
1 year
1 year
Glass (thermal breakage)
1 year
1 year
Plated, painted finishes (including interior reflective
glass)
1 year
1 year
Refractory lining
1 year
1 year
Mesh/Glass safety barriers
1 year
1 year
Power Vent Control box
1 year
1 year
Montigo Venting (excluding terminations)
15 years
1 year
QUALIFICATIONS TO THE WARRANTY
This Warranty only covers gas appliances installed in the United
States or Canada.
To receive the benefits of this warranty, the appliance must
be purchased, installed and serviced annually by a dealer
authorized by the Companies for the warranty to be valid.
The gas appliance must be installed by a licensed professional
in accordance with The Companies' installation instructions
and local building codes. The warranty on the appliance covers
only components manufactured by The Companies. The use of
components manufactured or supplied by other manufactures
and used in conjunction with the appliance could create serious
safety hazards, may result in the denial of certification by
recognized national safety agencies and could violate local
building codes. Such use may untimely void this warranty. This
warranty does not cover any damages occurring from the
use of any components not manufactured or supplied by The
Companies.
If the components of the appliance covered by this warranty
are found to be defective within the time frame stated (see The
Companies investigation of claims), the companies will, at its
option, replace or repair defective components of the appliance
manufactured by the company at no charge and will also pay for
labor costs (in accordance with schedule) incurred in replacing
or repairing components. If repair or replacement is not
commercially practical, the companies will, at its sole discretion,
provide a current or most like unit, excluding the cost of labor
unless the labor is covered by the terms of the warranty.
This warranty covers only parts and labor as provided above.
In no case shall the companies be responsible for materials,
components or construction. All replacement or repair
components will be shipped F.O.B. from the nearest Company
factory.
LIMITATION ON LIABILITY
It is agreed and understood that The Companies sole obligation,
and purchaser's exclusive remedy under this warranty, under
any other warranty, expressed or implied, or in contract, tort or
otherwise, shall be limited to repair or replacement as specified
above. The opinion of The Companies with respect to these
matters shall be final.
In no event shall The Companies be responsible for any
incidental or consequential damages caused by (but not limited
to) improper installation, installation by an unqualified or
unauthorized installer, accident, lack of regular maintenance,
user error, abuse, misuse, Acts of God, power surges, floods,
natural disasters, force majeure, defects in its appliance whether
such damage occurs or is discovered before or after replacement
or repair, and whether or not such damage is caused by The
Companies negligence. Some jurisdictions do not allow the
exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you. The
duration of any implied warranty with respect to the appliance
is limited to the duration of the foregoing warranty. Some
jurisdictions do not allow limitations on how long an implied
warranty lasts, so the above limitation or exclusion may not
apply to you.
The appliance must be subjected to normal use. The appliance
is designed to burn natural gas (NG) or liquefied petroleum (LP)
only. Burning conventional fireplace fuels such as wood, coal or
any other solid fuel will cause damage to the appliance, produce
excessive temperatures will result in a fire hazard and void all
warranties. This warranty is transferable. The appliance must
remain in its original place of installation to be valid.
12
XG0517
Appendix
Appendix B: Warranty Continued
EXCLUSIONS TO WARRANTY
Corrosion or rust of any kind due to a lack of maintenance,
inadequate combustion air or improper venting and corrosive
chemicals/environments, expansion and contraction of metals or
minor movements of components causing noise are not covered
by this warranty.
Willful misconduct (i.e. use of the appliance with problems
known to the purchaser and causing further damages), including
unauthorized or self-performed 'fixing' or exploration of the
appliance's internal workings will void the warranty.
Appliances on which the serial number has been altered, defaced,
removed or made illegible will void the warranty.
Costs incurred for diagnosis, service work, shipping and handling
of defective or replacement parts are not covered under this
warranty.
The published warranties are not applicable for any equipment
manufactured by The Companies that has been sold direct to
the consumer via internet or auction websites. The Companies
do not endorse, approve or certify any online sale of its products
through auction websites, online retailers or any other method
of online sales direct to consumers.
USA Offices
6955 Salashan Parkway
Ferndale WA, 98248
techsupport@montigo.com
Canadian Offices
27342 Gloucester Way
Langley, BC V4W 4A1
techsupport@montigo.com
The terms and conditions of this warranty may be altered or
amended from time to time without prior notice.
WARRANTY PERIOD: Warranty coverage begins on the date of
original purchase. In the case of new construction, warranty
coverage begins on the date of first occupancy of the dwelling
or six months after the sale of the product by an independent,
authorized Company dealer/ distributor, whichever occurs
earlier.
INVESTIGATION OF CLAIMS AGAINST
WARRANTY
The Companies reserve the right to investigate any and all claims
against this warranty and decide upon method of settlement.
The Companies are not responsible for work done without
written consent of The Companies.
The Companies shall in no event be responsible for any warranty
work done without first obtaining the Companies written
consent.
The Companies employees and dealers have no authority to
make any warranties to neither alter this warranty nor authorize
any remedies in addition to or inconsistent with those stated
within this warranty.
IF WARRANTY SERVICE IS NEEDED
To make a claim under this warranty, contact your installing
dealer or contractor. The installing dealer is responsible for
providing service and will contact the companies to initiate
warranted parts replacements. In the event the installing
dealer is unavailable, contact your nearest authorized Montigo
dealer (www.Montigo.com) or contact Montigo direct at
techsupport@ montigo.com. Ensure you have your sales receipt
and the model and serial number of your appliance.
DO NOT ATTEMPT TO DO ANY SERVICE WORK YOURSELF
If you cannot locate the installing dealer, or nearest dealer/
distributor, you must notify The Companies in writing.colors,
styles and products.
XG0517
13
Appendix
Appendix C: Amendment
(Gas Fireplace / Equipment sold in the State of Massachusetts)
5.08: Modifications to NFPA-54, Chapter 10
(1) Revise NFPA-54 section 10.5.4.2 by adding a second exception as
follows:
Existing chimneys shall be permitted to have their use continued
when a gas conversion burner is installed, and shall be equipped
with a manually reset device that will automatically shut off the
gas to the burner in the event of a sustained back-draft.
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in whole
or in part for residential purposes, including those owned
or operated by the Commonwealth and where the side wall
exhaust vent termination is less than seven (7) feet above
finished grade in the area of the venting, including but not
limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time
of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gas fitter shall observe
that a hard wired carbon monoxide detector with an alarm and
battery back-up is installed on the floor level where the gas
equipment is to be installed. In addition, the installing plumber
or gas fitter shall observe that a battery operated or hard wired
carbon monoxide detector with an alarm is installed on each
additional level of the dwelling, building or structure served by
the side wall horizontal vented gas fueled equipment. It shall be
the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired
carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled
equipment is installed in a crawl space or an attic, the hard
wired carbon monoxide detector with alarm and battery backup may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply with
the above requirements; provided, however, that during said
thirty (30) day period, a battery operated carbon monoxide
detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon
monoxide detector as required in accordance with the above
provisions shall comply with NFPA 720 and be ANSI/UL 2042 listed
and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be
permanently mounted to the exterior of the building at a
minimum height of eight (8) feet above grade directly in line with
the exhaust vent terminal for the horizontally vented gas fueled
heating appliance or equipment. The sign shall read, in print
size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY
BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
4. INSPECTION. The state or local gas inspector of the side wall
horizontally vented gas fueled equipment shall not approve
the installation unless, upon inspection, the inspector observes
carbon monoxide detectors and signage installed in accordance
with the provisions of 248 CMR 5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248
CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled “Equipment Not
Required To Be Vented” in the most current edition of NFPA 54 as
adopted by the Board; and
2. Product Approved side wall horizontally vented gas fueled
equipment installed in a room or structure separate from the
dwelling, building or structure used in whole or in part for
residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING
SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment
provides a venting system design or venting system
components with the equipment, the instructions provided
by the manufacturer for installation of the equipment and the
venting system shall include:
1. Detailed instructions for the installation of the venting system
design or the venting system components; and
2. A complete parts list for the venting system design or venting
system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING
SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled
equipment does not provide the parts for venting the flue
gases, but identifies “special venting systems”, the following
requirements shall be satisfied by the manufacturer:
1. The referenced “special venting system” instructions shall
be included with the appliance or equipment installation
instructions; and
2. The “special venting systems” shall be Product Approved by
the Board, and the instructions for that system shall include a
parts list and detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved
side wall horizontally vented gas fueled equipment, all venting
instructions, all parts lists for venting instructions, and/or all
venting design instructions shall remain with the appliance or
equipment at the completion of the installation.
(3) After NFPA-54 section 10.10.4.2 add a new section 10.10.4.3 as
follows:
When more than four gas appliances are to be vented through a
common gas vent or common horizontal vent manifold, a plan of
the proposed vent installation shall be submitted to the Inspector
and the serving gas supplier for review and approval.
Extraction from: Massachusetts Rules and Regulations
5.00: Amendments To 2002 Edition Of ANSI Z223.1-NFPA-54
14
XG0517
Notes
XG0517
15
Installation & Maintenance Manual
PVHEX58-300 &
PVHEX510-300
5/8 and 5/10 External Wall
Power Vent
XG0517
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising