Montigo | PVVEX58-200 PVVEX510-300 Roof Power Vent System | Instruction | Montigo PVVEX58-200 PVVEX510-300 Roof Power Vent System Instruction

Montigo PVVEX58-200 PVVEX510-300 Roof Power Vent System Instruction
Installation & Maintenance Manual
PVVEX58-200 & PVVEX510-300
5/8 AND 5/10 EXTERNAL ROOF
POWER VENT
•
The installation of this fireplace must be done by a
qualified and certified gas appliance installer.
•
Check local codes and read all instructions prior to
installation.
®
C
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury,
death, or property damage.
US
NOTICE
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for suture reference.
— Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
•
Do not try to light any appliance.
•
Do not touch any electrical switch; do not use any
phone in your building.
•
Leave the building immediately.
•
Immediately call your gas supplier from a neighbour's
phone. Follow the gas supplier’s instructions.
•
If you cannot reach your gas supplier, call the fire
department.
— Installation and service must be performed by a qualified
installer, service agency or the gas fitter.
CAUTION
Installation and service must be performed by a qualified installer,
service agency or the gas fitter.
DANGER
Read and understand this manual. Improper installation, adjustment,
alteration, service or maintenance can cause serious injury, property
damage or even death. For assistance or additional information
consult a qualified installer, service agency or the gas supplier.
WARNING
Some materials used in the manufacturing process of this product can
expose you to Benzene which is known in the State of California to
cause cancer and birth defects or other reproductive harm. For more
information go to www.P65warnings.ca.gov
XG0518 - 100319
General
Safety Alert Key
Indicates practices that are important, but
not related to personal injury.
Introduction
This installation guide covers installation of the Inline Power Vent
System only. This system is designed to allow installation of gas
fireplaces that cannot be done with a standard Direct Vent gas
fireplace installation. Only for use on DelRay, Distinction, H Series
that uses the 4/7 venting system.
ONLY USE WITH APPROVED FIREPLACES - see fireplace installation
manual.
Read through the fireplace's installation & maintenance manual,
as it must also be adhered to.
Power Cord Harnesses:
The Montigo warranty will be voided by, and Montigo disclaims any
responsibility for, the following actions:
•
EPVH10 - 10 foot power cord and harness
•
EPVH20 - 20 foot power cord and harness
•
EPVH40 - 40 foot power cord and harness
•
EPVH50 - 50 foot power cord and harness
•
EPVH60 - 60 foot power cord and harness
•
EPVH80 - 80 foot power cord and harness
•
EPVH100 -100 foot power cord and harness
IMPORTANT:
For vent configurations and power vent locations,
refer to fireplace manual.
2
MODEL
Congratulations on your purchase of a Montigo Fireplace.
PVVEX58-200
PVVEX510-300
X
X
Speed
Indicates a hazardous situation which, if not
avoided, WILL result in minor or moderate
injury.
NOTICE
Maximum Airflow
CAUTION
Indicates a hazardous situation which, if not
avoided, COULD result in death or serious
injury or property damage.
5/8 Pipe Dimentions
Indicates a hazardous situation which, if
not avoided, WILL result in death or serious
injury or property damage.
WARNING
5/8 Pipe Dimentions
DANGER
200 CFM
2700 RPM
300 CFM
2700 RPM
Figure 1 PV Specifications
CAUTION
When cold air enters the building interior, primarily at the air intake
end, condensation may occur on the exterior of the pipe. To limit this
condensation, install insulation over the last twenty feet of pipe. Also,
by sloping the last 20' of pipe downwards towards the exterior of the
building will help eliminate any condensation problems, should they
occur. Ensure the termination is securely fastened and sealed to the
pipe. Fasten the termination to the exterior of the building with water
tight sealant and the appropriate fasteners.
XG0521 - 180904
General
Section A: Before You Begin
IMPORTANT MESSAGE: SAVE THESE INSTRUCTIONS
The unit must be installed in accordance with these instructions.
Carefully read all the instructions in this manual first. Consult the Local
Gas Branch to determine the need for a permit prior to starting the
installation. It is the responsibility of the installer to ensure this fireplace
is installed in compliance with the manufacturers instructions and all
applicable codes.
NOTICE
Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the appliance
and to replace any part of the control system and any gas control that
has been under water
Contents
Safety Alert Key���������������������������������������������������������������������������������� 2
Introduction��������������������������������������������������������������������������������������� 2
Section A: Before You Begin ........................................................................3
Section 1: Dimensions����������������������������������������������������������������������� 4
PVVEX58-200 Product Dimensions.............................................................4
PVVEX510-300 Product Dimensions..........................................................5
Section 2: Installing the power vent������������������������������������������������ 6
Installing the power vent...............................................................................6
Conduit and Wiring Clearances...................................................................7
Power Vent Wiring...........................................................................................7
Capacitor Removal and Servicing................................................................8
Motor and Capacitor Replacement.............................................................9
Wiring schematic for Proflame 2 with power vent................................11
NOTICE
Appendix A: Venting Terminations������������������������������������������������ 12
Due to high temperatures, the appliance should be located out of
traffic and away from furniture and draperies
Appendix B: Warranty Continued�������������������������������������������������� 14
Appendix B: Warranty��������������������������������������������������������������������� 13
Appendix C: Amendment���������������������������������������������������������������� 15
(Gas Fireplace / Equipment sold in the State of Massachusetts)
����������������������������������������������������������������������������������������������������������� 15
NOTICE
Children and adults should be alerted to the hazards of high surface
temperature and should stay away to avoid burns or clothing ignition
NOTICE
Clothing or other flammable material should not be placed on or near
the appliance
NOTICE
Installation and repair should be done by a qualified service person.
The appliance should be inspected before use and at least annually
by a professional service person. More frequent cleaning might be
required due to excessive lint from carpeting, bedding material, etc. It
is imperative that control compartments, burners, and circulating air
passageways of the appliance be kept clean
XG0521 - 180904
3
REV.
DESCRIPTION
DATE
APPROVED
B
WAS 24" BASE NOW 18" BASE
09/30/2019
-
Thursday, October 03, 2019 10:42:29 AM
General
Section 1: Dimensions
A
PVVEX58-200 Product Dimensions
18.000
18.000
!IMPORTANT!
DIMENSIONS ARE IN INCHES
MAINTAIN AT LEAST
TOLERANCES:
2.00" CLEARANCE
FRACTIONAL 1/32"
.015"
TWO PLACE DECIMAL
TO COMBUSTIBLES
THREE PLACE DECIMAL .005"
ALL BENDS ARE ASSUMED
ALL AROUND THETOCOLLAR
BE 90 UNLESS NOTED
OTHERWISE.
DIMENSIONS
SECTION A-A
DRAWN BY
PVVEX58-200
18.000
DATE
NAME
DB 10/3/2019
CHECKED BY
MATERIAL
MTK
K-FACTOR
REV.
SIZE DWG. NO.
A
B
PVVEX58-200
SCALE 1:6
SHEET 2 OF 4
WEIGHT:
Y:\Products\Residential Products\Ventilation Systems\Roof Mounr Power Vent PVVEX58-200\PVVEX58-200
.913
18.000
3.660
2.000
20.73
[527]
PROPRIETARY AND CONFIDENTIAL
7.918
10.500
[267]
18.000
[457]
2.000
B THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
R
1275
F1I7N.0IS .500MAX
HED
CUR
B
FRAMING DIMENSIONS
(NTS)
18.000
4.950
7.918
17
.02
5
ROUGH IN KIT
PVVEX58-200
f Mounr Power Vent PVVEX58-200\PVVEX58-200
2.000
U
ROUGH IN KIT
Thursday, October 03, 2019 10:42:29 AM
4.950
A
14.288
2.000
18.000
[457]
5
[126]
6.997
3.252
18.897
18.000
[457]
8
[203]
DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN BY
Figure 2.d Unit dimensions (Tolerance
± ⅛"). 1/32"
FRACTIONAL
.015"
TWO PLACE DECIMAL
CHECKED BY
THREE PLACE DECIMAL .005"
MATERIAL
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
K-FACTOR
OTHERWISE.
18.000 DATE
NAME
DB 10/7/2019
MTK
SIZE DWG. NO.
A PVVEX58-200 FULL A
FRAMING DIMENSIONS
SCALE 1:12 WEIGHT:
ION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN
PERMISSION OF CANADIAN HEATING PRO
PVVEX58-200
NS
4.950
4
7.918
DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN BY
FRACTIONAL 1/32"
.015"
TWO PLACE DECIMAL
CHECKED BY
THREE PLACE DECIMAL .005"
MATERIAL
ALL BENDS ARE ASSUMED
DATE
NAME
DB 10/3/2019
XG0521 - 180904
MTK
SIZE DWG. NO.
Installation
PVVEX510-300 Vertical Power Vent Termination
PVVEX510-300 Product Dimensions
10"
253
24"
610
5"
126
24"
610
1
"
2
419
16
3
"
8
466
18
7
"
8
175
6
13"
330
18"
458
XG0518 - 100319
18"
458
5
Installation
Section 2: Installing the power vent
Power Vent Components
Installing the power vent
Step 3: Remove the last section
of vent pipe and put off to the
side to be used later. Take the
rough in box from the power.
Power Head
Vent Clamp
Framing Box
Vent
Figure 3.d Installing the Rough-in Kit.
Chase
Step 4: Unscrew 6 screws
securing the control cable cover
and remove it.
Figure 3.a Power vent components Exploded View
Step 1: Construct a chase box around the vent penetration with
dimensions as shown in figure 2a.
PVVEX58-200 PVVEX58-300
5
17½" MAX.
10 "
8
PVVEX510-300 PVVEX58-200
270
20"
10⅝"
23½"Max
MAX.
Min
Note: Follow local
and/or national code
requirements for roof
clearances.
Step 5: Unscrew 2 screws
securing strain relief plate and
remove it.
PVVEX510-300
PVVEX510-300
13"
13"
[330]
PVVEX58-200
17½"
20"MAX.
PVVEX510-300
Max
23½" MAX.
Figure 3.f Removing strain relief plate.
24
Min
5
PVVEX58-200
10 "
8
10⅝" MIN.
270
PVVEX510-300
Min
13" MIN.
Control Cable
Step 2: Install the electrical
harness (EPVH-10-100) that will
communicate with the Power
Vent. Run vent pipe from the
fireplace to the chase. Make sure
the last section is female end up
and is flush with the top of the
chase without going above it.
See figure 2b.
Vent Pipe
Figure 3.c Installing the Rough-in Kit.
6
Figure 3.e Unscrewing control cable cover
Step 6: Loosen nut on the strain
relief of the control cable. Pass
control cable through slot in
rough in box making sure the
nut stays is on the opposite
side of the rough in box as the
strain relief. Push the strain
relief through the hole in the
roughin box.
Figure 3.g
Step 7: Reinstall the strain relief
plate. Make sure the strain relief
nut is above the strain relief
plate. Tighten the nut on the
strain relief.
Figure 3.h
XG0518 - 100319
Min
chase box around the
ation with the dimensions
ere.
20"
Max
Installation
24
Min
e
5
10 "
8
270
Min
Step #4
Step #2
the Power Vent module.
the base plate in any location
necessary to keep the structure
of the building free of water or
moisture.
Figure 3.i
Attachment
screw
locations
Figure 3.n
Conduit and Wiring Clearances
Step 9: Drop the rough in box
over top of and inside the Chase.
Connect the power vent harness as outlined. Connect the wiring to the
fireplace as outlined in the schematic showin in Figure 14 Section 3.
Ensure that the proper clearances are maintained for the wiring and
conduit. When installing the wiring, it must never run above the vent
pipe and it must be at lest 1" clear of all venting and other hot surfaces.
power vent Rought-in Kit.
he electrical cover plate
e of the rough in kit. Pull
l cable through the slot in
m of the box and insert the
he rectangular hole in the
e. Re-attach the cover
Figure 3.j
wire harness throught the
hole in the bottom corner of
-in box and
snap
intothe
thelast section of
Step
10: Take
ded.
pipe and install the vent clamp
around the pipe. The bottom of
the band should be 6 3/8" from
the top of the pipe. Tighten the
clamp using the supplied nut
and screw.
1” Clearance
Wire
6⅜
Power Vent Wiring
Figure 3.k
Step 11: Drop pipe down into
the frame box. The pipe should
be flush with the top of the frame
box. Secure pipe connection
below.
BLUE
BLACK
BROWN
C
WHITE
BLACK
GREEN
BLUE
Step 12: Connect power cable
of termination to the molex of
the control cable.
6 PIN MOLEX
CONNECTOR
Figure 3.l
Power Vent Wiring
RED
KEY WAY
Step 8: Push the molex
connector of the control cable
through the hole in the control
cable cover. Make sure the
molex clicks in place so it does
not fall out. Screw control cable
cover back in place.
Place termination head over chase
and fasten with 4 screws on the
vertical
sides
the base
Stepof13:
Placeplate.
power vent
Install the vent pipe female end
up 2"
or
sealchase
the base
over
and plate
fasteninwith 4
- 3" from the top of the chaseSilicone
box.
any location
necessary
to keep the
on the vertical sides of
Install the electrical harness structure
(EPVH- screws
of the building free of
the base plate. Silicone of seal
10-100) that will communicate
withor moisture.
water
AIR SWITCH
Figure 3.m
XG0518 - 100319
7
Installation
Vacuum Switch Replace
Vacuum Switch Replacement [REC1226]
Turn off power and gas before servicing.
Step 1: Disconnect 2 red wires
connected to the vacuum switch.
Figure 5.aa
Step 2: Unscrew vacuum switch from top seperator. Remove silicone
hose from nipple.
Figure 5.bb
Step 3: Connect new vacuum switch to existing wires, do not connect
a wire to the center terminal. Reconnect silicone tube.
Figure 5.cc
Step 4: Reconnect the screws securing the switch to the top separator.
8
XG0518 - 100319
Installation
Capacitor Removal and Servicing
Capacitor Replacement [REC1252]
Turn off power and gas before servicing.
PVVEX58-300
Motor
Servicing
Step
1: Removal
Remove/ the
4 outer
screws that fasten the top cover
Top Cover
toStep
the 1:
termination. Remove the
Screws x 4 plcs
cover.
Step 5: Strip ends of all cut wires and new capacitor. Screw new
capacitor and ground wire to the motor using the existing screw you
saved. Using a small bell connector, connect the blue wire from the
motor to the black fibre wire from the power cable.
Top Cover
a) Remove the 4 outer screws
that fasten the Top Cover to
the termination
b) Remove the Cover.
Figure 5.e
Figure 5.a
Step 2: Cut zap straps.
Step 2:
Unscrew ground wire/capacitor bracket from motor.
a) Remove the 4 outer screws
WARNING:
this Baffle
screw.
that fastenSave
the Wind
to
the termination.
b) Lower the Wind Baffle to
rest on the Rain Skirt.
Screw Locations
x 4 plcs
Step 6: Using the large bell connector, attach the white fibre wire
from the power cable to the black from the motor and a black wire
from capacitor. Attach the brown from the motor to the other black
from the capacitor.
Wind Baffle
Rain Skirt
Step 3:
Top Separator
Figure 5.b
a) Remove the 5 outer screws
Screw Locations
that fasten the Top Separator
x 5 plcs
to the termination.
Step
3: Cutthebrown
wire from motor and black wire from capacitor.
b) Remove
Top Separator.
Cut black fibre wire from power cable and blue wire from motor.
Figure 5.f
Step 7: Zap strap wires together in a neat bunch so that no wires can
fall into the motor. Zap strap wires to loop in the top of the capacitor.
Figure 5.c
Step 4: Cut white fibre from power cable, black wire from capacitor
and black wire from motor. Remove and dispose of old capacitor and
open REC1252
Figure 5.d
XG0518 - 100319
Figure 5.g
Step
8: Test the power vent and
PVVEX58-300
Motor
/ Servicing
make
sureRemoval
it is working
properly.
When looking down at the top
of the
the fan should be
Stepmotor
1:
spinning counterclockwise. If it
a) Remove the 4 outer screws
is spinning
the
wrong
way or
that fasten
the
Top Cover
to not
theittermination
at all
is wired incorrectly. Put
Remove the Cover.
theb)top
cover back on using the
supplied replacement screws.
Step 2:
a) Remove the 4 outer screws
that fasten the Wind Baffle to
the termination.
b) Lower the Wind Baffle to
rest on the Rain Skirt.
Top Cover
Top Cover
Screws x 4 plcs
Figure 5.h
Screw Locations
x 4 plcs
Wind Baffle
9
Installation
Motor and Capacitor Replacement
Step 5: Cut the black fibre wire from the power cable. Cut the white
fibre wire from the power cable.
[REC 1253]
Turn off power and gas before servicing.
PVVEX58-300
Motor
Servicing
Step
1: Removal
Remove/ the
4 outer
PVVEX58-300
Motor
Removal
/
Servicing
PVVEX58-300
screws that fasten the
top cover
Motor
Removal / Remove
Servicingthe
Top Cover
toStep
the 1:
termination.
Screws x 4 plcs
cover.
Top Cover
Step 1:
a) Remove the 4 outer screws
that fasten
the Top Cover to
Step
1:
a)
the 4 outer screws
theRemove
termination
that
fastenthe
the4
Top
Cover
to
b) Remove
Cover.
a)
outer
screws
the
thattermination
fasten the Top Cover to
b) Remove
the Cover.
the
termination
b) Remove the Cover.
Top Cover
Top Cover
Top Cover
Screws x 4 plcs
Top Cover
Screws x 4 plcs
Figure 5.c
Step 6: Remove 4 screws securing the motor mounting plate. Lift out
motor and capacitor.
Figure 5.a
Step 2:
2: Remove the 4 outer
Step
screws
wind
Step
2: that
a) Remove
thefasten
4 outer the
screws
that fasten
Wind BaffleLower
to
Step
2: the the
baffle
to
termination.
a)
the 4 outer screws
theRemove
termination.
the
wind
baffle
toBaffle
rest
ontothe
that
fasten
the
Baffle
b) Remove
Lower
the
Wind
to
a)
the
4Wind
outer
screws
the
termination.
restskirt.
on
the Rain
Skirt.
that
fasten
the Wind
Baffle to
rain
b)
the Wind Baffle to
theLower
termination.
rest
on the
Skirt.
b)
Lower
theRain
Wind
Baffle to
rest on the Rain Skirt.
Screw Locations
x 4 plcs
Screw Locations
x 4 plcs
ScrewBaffle
Locations
Wind
x 4 plcs
Wind Baffle
Wind Baffle
Rain Skirt
Rain Skirt
Rain Skirt
Figure 5.b
Step 3:
Top Separator
Step
3:
the 5 outer
Step
3: Remove
a) Remove
the 5 outer screws
screws
the top
that fasten
thefasten
Top Separator
Step
3: that
a)
thethe
5 outer
screws
to Remove
the termination.
separator
to
termination.
that
fastenthe
the5
Top
Separator
b)
Top
Separator.
a)
Remove
outer
screws
Remove
thethe
topTop
separator.
to
the
termination.
that
fasten
Separator
b) Remove
the Top Separator.
to
the termination.
b) Remove the Top Separator.
Top Separator
TopLocations
Separator
Screw
x 5 plcs
Screw Locations
x 5 plcs
Screw Locations
x 5 plcs
Figure 5.c
Step 7: Drop new motor assembly into the power vent and screw with
supplied 4 screws and star washers. Line up cut out in motor mounting
plate with electrical conduit. Remove the ground wire screw from the
motor. NOTE: Save this screw for later.
Figure 5.c
Figure 5.c
Step 8: Using the ground screw, screw the capacitor bracket and the
ground wire to the motor. Strip the ends of all the wires. Using the large
bell connector, connect the white fibre wire from the power cable to the
black wire from the motor and one of the black wires from the capacitor.
Step 4: Cut zap straps.
Unscrew ground wire/capacitor bracket from motor.
Figure 5.b
Figure 5.c
10
XG0518 - 100319
Step 1:
Screws x 4 plcs
a) Remove the 4 outer screws
that fasten the Top Cover to
the termination
b) Remove the Cover.
Installation
Step 2:
a) Remove the 4 outer screws
that fasten the Wind Baffle to
the termination.
b) Lower the Wind Baffle to
rest on the Rain Skirt.
Screw Locations
x 4 plcs
Wind Baffle
Rain Skirt
Step 9: Using a small bell connector, connect the black fibre wire from
the power cable to the blue wire of the motor. Using the other small
bell connector, connect the other black wire from the capacitor to the
brown wire from the motor.
Step
12: Reinstall the top
PVVEX58-300
Motor
separator
with /5Servicing
supplied
Step
3: Removal
screws.
a) Remove the 5 outer screws
that
the Top Separator
Step fasten
1:
to the termination.
b)
Remove
the
Top
Separator.
a) Remove the 4
outer
screws
that fasten the Top Cover to
the termination
b) Remove the Cover.
Top Separator
Top Cover
Screw Locations
Cover
x Top
5 plcs
Screws x 4 plcs
Figure 5.a
Step 13: Reinstall the wind
baffle
with supplied screws.
Step 2:
Figure 5.c
Step 10: Using a zap strap to bundle the wires neatly together. Using
another zap strap, secure the bundle to the capacitor.
a) Remove the 4 outer screws
that fasten the Wind Baffle to
the termination.
b) Lower the Wind Baffle to
rest on the Rain Skirt.
Screw Locations
x 4 plcs
Wind Baffle
Rain Skirt
Figure 5.b
Figure 5.c
Step 11: Using the last two zap
straps secure the wires to the leg
of the motor. Make sure none
of the wires can get caught in
the motor.
PVVEX58-300
Step
Step14:
3: Test the power vent and
Motor
Removal
/ Servicing
make
sure
it is working
properly.
a)
Remove
the
5
outer
screws
When
looking down at
the top
that fasten the Top Separator
ofStep
motor
the fan should be
tothe
the1:
termination.
b) Remove
the Top Separator.If it
spinning
counterclockwise.
a) Remove the 4 outer screws
isthat
spinning
wayto
or not
fastenthe
thewrong
Top Cover
atthe
alltermination
it is wired incorrectly. Put
b) Remove the Cover.
the top cover back on using the
supplied replacement screws.
Screw Locations
x 5 plcs
Top Cover
Screws x 4 plcs
Figure 5.c
Step 2:
a) Remove the 4 outer screws
that fasten the Wind Baffle to
the termination.
b) Lower the Wind Baffle to
rest on the Rain Skirt.
Figure 5.c
Screw Locations
x 4 plcs
Wind Baffle
Rain Skirt
Step 3:
a) Remove the 5 outer screws
that fasten the Top Separator
to the termination.
b) Remove the Top Separator.
XG0518 - 100319
Top Separator Top Cover
Top Separator
Screw Locations
x 5 plcs
11
Installation
Wiring schematic for Proflame 2 with power vent
SPARK
GREEN
WHITE
BLACK
SENSOR
MAIN
Power
120VAC 60 Hz
6 Amps
MAIN ON/OFF
SWITCH
ELLOW
ELLOW
CPI/IPI SWITCH
6
WHITE
ELLOW/GREEN
ORANGE
PILOT
10
GREEN
Wht
BLACK
BROWN
ELLOW
ORANGE
R
Wht
VARIABLE SPEED
COMFORT FANS
BLACK
WHITE
6
SW1
GREEN
GREEN
BLACK
BLACK
WHITE
ELLOW
ELLOW
BROWN
AIR
SWITCH
RED
WHITE
Lights
ON/OFF
BLACK
SPARK
POWER
VENT
GREEN
WHITE
WIRED
TO WALL
SWITCH
BLACK
SENSOR
OR
MAIN
Power
120VAC 60 Hz
6 Amps
OPTIONAL
MAIN ON/OFF
SWITCH
ELLOW
ELLOW
CPI/IPI SWITCH
6
WHITE
ELLOW/GREEN
PILOT
ORANGE
GREEN
R
10
W
BLACK
BROWN
ELLOW
ORANGE
W
(OPTIONAL) STEPPER MOTOR
VARIABLE SPEED
COMFORT FANS
(OPTIONAL)
BLACK
WHITE
6
SW1
12
GREEN
GREEN
BLACK
BLACK
WHITE
ELLOW
ELLOW
BROWN
POWER
VENT
AIR
SWITCH
RED
XG0518 - 100319
Appendix
Appendix A: Venting Terminations
Covered
Alcove Detail
2’
2’
17.5’’
2’
Covered
Alcove Detail
Vinyl Siding
2’
29.5’’
11.5’’
17’’
Must use Vinyl Siding
Termination Shield
Location
Canada*
USA**
A
clearance to the termination frame above grade, veranda, porch, deck, or balcony
12 inches
12 inches
B
clearance to top of doors or operable windows
12 inches
12 inches
C
clearance to sides or bottom of door or operable windows
12 inches
9 inches
D
clearance to permanently closed window when installed with approved glass penetration termination
0
0
E
clearance to permanently closed window Recommended to prevent condensation
16 inches
16 inches
F
clearance to ventilated soffit located within a horizontal distance to 24 inches from centerline of termination
22 inches
22 inches
30 inches to combustibles
16 inches to non-combustibles
30 inches to combustibles
16 inches to non-combustibles
G
clearance to unventilated soffit
H
clearance to outside corner
9 inches
9 inches
I
clearance to inside corner
12 inches
12 inches
J
clearance to each side of the vertical centerline of a metre or regulatory assembly to a maximum vertical distance of 15ft
3 feet
3 feet
K
clearance to service regulator vent outlet
3 feet
3 feet
L
clearance to non mechanical air supply inlet to the building or combustion air inlet to other appliance for appliance <=
100.000 BTU/H (30 KW)
12 inches
12 inches
3 feet above air inlet
M
clearance to forced air supply inlet
6 feet
N
clearance above paved sidewalk or paved driveway located on public property
7 feet
7 feet
P
clearance under veranda, porch, deck, or balcony
22 inches to combustibles
16 inches to non-combustibles
22 inches to combustibles
16 inches to non-combustibles
Q
clearance above roof
2 feet
2 feet
R
clearance to adjacent walls and neighboring buildings
2 feet
18 inches
S
clearance from corner in recessed location
12 inches
12 inches
T
Maximum depth of recessed location
4 feet
4 feet
U
Maximum width for back wall of recessed location
2 feet
2 feet
V
Horizontal clearance between two terminations that are level
W
Horizontal clearance (centre to centre) between two terminations that are not level
0
0
18 inches
18 inches
Note 1: For N a vent shall not terminate directly above the sidewalk or paved driveway which is located between two single family dwellings and serve both dwelling.
Note 2: For P only permitted if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor
Note 3: For J, K, and as specified in CGA B149 installation code. Local codes or regulations may vary.
* Based on CGA B149.1 Natural Gas and Propane installation code. Local codes may vary, please check with local regulatory agency.
** Based on ANSI Z223.1/NFPA 54 National Fuel Gas Code. Local codes may vary, please check with local regulatory agency.
XG0518 - 100319
13
Appendix
Appendix B: Warranty
MONTIGO RESIDENTIAL WARRANTY PROGRAM
Canadian Heating Products Inc. and/or Montigo DelRay Corp
(collectively referred to herein as "The Companies"), warrants the
Montigo gas appliance (referred to herein as 'the appliance') to
be free from defects in materials and workmanship at the time
of manufacture. The gas appliance and related components are
further subject to the terms and conditions set forth below.
This warranty covers the following Montigo product series:
Distinction, H, I, L, Linear P and PL, R, RP, Mahana and DelRay
Component
Coverage Period
Labor Coverage
Firebox, heat exchanger
15 years
1 year
Main burner
15 years
1 year
Gas control valve and related control components
(pilot assembly, spark electrode flame sensors,
thermopile)
1 year
1 year
Electrical components (internal blowers, ignition
control module, wiring, switches, remote control
systems, blower control module, accent bulbs)
1 year
1 year
Firebox media (logset, glass beads, river rocks)
1 year
1 year
Glass (thermal breakage)
1 year
1 year
Plated, painted finishes (including interior reflective
glass)*
1 year
1 year
Refractory lining
1 year
1 year
Mesh/Glass safety barriers
1 year
1 year
Power Vent Control box
1 year
1 year
Montigo Venting (excluding terminations)
15 years
1 year
* Exterior painted surfaces exempt
QUALIFICATIONS TO THE WARRANTY
This Warranty only covers gas appliances installed in the United
States or Canada.
To receive the benefits of this warranty, the appliance must
be purchased, installed and serviced annually by a dealer
authorized by The Companies for the warranty to be valid.
The gas appliance must be installed by a licensed professional
in accordance with The Companies' installation instructions
and local building codes. The warranty on the appliance covers
only components manufactured by The Companies. The use of
components manufactured or supplied by other manufacturers
and used in conjunction with the appliance could create serious
safety hazards, may result in the denial of certification by
recognized national safety agencies and could violate local
building codes. Such use may untimely void this warranty. This
warranty does not cover any damages occurring from the
use of any components not manufactured or supplied by The
Companies.
warranties. This warranty is transferable. The appliance must
remain in its original place of installation to be valid.
If the components of the appliance covered by this warranty
are found to be defective within the time frame stated (see The
Companies investigation of claims), The Companies will, at its
option, replace or repair defective components of the appliance
manufactured by The Companies at no charge and will also
pay for labor costs (in accordance with schedule) incurred in
replacing or repairing components. If repair or replacement
is not commercially practical, The Companies will, at its sole
discretion, fully discharge all obligations under the warranty by
refunding the verified dealer purchase price of the appliance,
excluding the cost of labor unless the labor is covered by the
terms of the warranty.
This warranty covers only parts and labor as provided above.
In no case shall the companies be responsible for materials,
components or construction, which are not manufactured or
supplied by The Companies, or for the labor necessary to install,
repair or remove such materials, components or construction. All
replacement or repair components will be shipped F.O.B. from
the nearest Company factory.
LIMITATION ON LIABILITY
It is agreed and understood that The Companies sole obligation,
and purchaser's exclusive remedy under this warranty, under
any other warranty, expressed or implied, or in contract, tort or
otherwise, shall be limited to repair, replacement or refund as
specified above. The opinion of The Companies with respect to
these matters shall be final.
In no event shall The Companies be responsible for any
incidental or consequential damages caused by (but not limited
to) improper installation, installation by an unqualified or
unauthorized installer, accident, lack of regular maintenance,
user error, abuse, misuse, Acts of God, power surges, floods,
natural disasters, force majeure, defects in its appliance whether
such damage occurs or is discovered before or after replacement
or repair, and whether or not such damage is caused by The
Companies negligence. Some jurisdictions do not allow the
exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you. The
duration of any implied warranty with respect to the appliance
is limited to the duration of the foregoing warranty. Some
jurisdictions do not allow limitations on how long an implied
warranty lasts, so the above limitation or exclusion may not
apply to you.
The appliance must be subjected to normal use. The appliance
is designed to burn natural gas (NG) or liquefied petroleum (LP)
only. Burning conventional fireplace fuels such as wood, coal or
any other solid fuel will cause damage to the appliance, produce
excessive temperatures will result in a fire hazard and void all
14
XG0518 - 100319
Appendix
Appendix B: Warranty Continued
EXCLUSIONS TO WARRANTY
USA Offices
Corrosion or rust of any kind due to a lack of maintenance,
inadequate combustion air or improper venting and corrosive
chemicals/environments, expansion and contraction of metals or
minor movements of components causing noise are not covered
by this warranty.
6955 Salashan Parkway
Willful misconduct (i.e. use of the appliance with problems
known to the purchaser and causing further damages), including
unauthorized or self-performed 'fixing' or exploration of the
appliance's internal workings will void the warranty.
Appliances on which the serial number has been altered, defaced,
removed or made illegible will void the warranty.
Costs incurred for diagnosis, service work, shipping and handling
of defective or replacement parts are not covered under this
warranty.
The published warranties are not applicable for any equipment
manufactured by The Companies that has been sold direct to
the consumer via internet or auction websites. The Companies
do not endorse, approve or certify any online sale of its products
through auction websites, online retailers or any other method
of online sales direct to consumers.
Ferndale WA, 98248
techsupport@montigo.com
Canadian Offices
27342 Gloucester Way
Langley, BC V4W 4A1
techsupport@montigo.com
The terms and conditions of this warranty may be altered or
amended from time to time without prior notice.
WARRANTY PERIOD: Warranty coverage begins on the date of
original purchase. In the case of new construction, warranty
coverage begins on the date of first occupancy of the dwelling
or six months after the sale of the product by an independent,
authorized Company dealer/ distributor, whichever occurs
earlier.
INVESTIGATION OF CLAIMS AGAINST
WARRANTY
The Companies reserve the right to investigate any and all claims
against this warranty and decide upon method of settlement.
The Companies are not responsible for work done without
written consent of The Companies.
The Companies shall in no event be responsible for any warranty
work done without first obtaining the Companies written
consent.
The Companies employees and dealers have no authority to
make any warranties to neither alter this warranty nor authorize
any remedies in addition to or inconsistent with those stated
within this warranty.
IF WARRANTY SERVICE IS NEEDED
To make a claim under this warranty, contact your installing
dealer or contractor. The installing dealer is responsible for
providing service and will contact the companies to initiate
warranted parts replacements. In the event the installing dealer
is unavailable, contact your nearest authorized Montigo dealer
(www.Montigo.com) or contact Montigo direct at techsupport@
montigo.com. Ensure you have your sales receipt and the model
and serial number of your appliance.
DO NOT ATTEMPT TO DO ANY SERVICE WORK YOURSELF
If you cannot locate the installing dealer, or nearest dealer/
distributor, you must notify The Companies in writing.
XG0518 - 100319
15
Appendix
Appendix C: Amendment
(Gas Fireplace / Equipment sold in the State of Massachusetts)
5.08: Modifications to NFPA-54, Chapter 10
(1) Revise NFPA-54 section 10.5.4.2 by adding a second exception as
follows:
Existing chimneys shall be permitted to have their use continued
when a gas conversion burner is installed, and shall be equipped
with a manually reset device that will automatically shut off the
gas to the burner in the event of a sustained back-draft.
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in whole
or in part for residential purposes, including those owned
or operated by the Commonwealth and where the side wall
exhaust vent termination is less than seven (7) feet above
finished grade in the area of the venting, including but not
limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time
of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gas fitter shall observe
that a hard wired carbon monoxide detector with an alarm and
battery back-up is installed on the floor level where the gas
equipment is to be installed. In addition, the installing plumber
or gas fitter shall observe that a battery operated or hard wired
carbon monoxide detector with an alarm is installed on each
additional level of the dwelling, building or structure served by
the side wall horizontal vented gas fueled equipment. It shall be
the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired
carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled
equipment is installed in a crawl space or an attic, the hard
wired carbon monoxide detector with alarm and battery backup may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply with
the above requirements; provided, however, that during said
thirty (30) day period, a battery operated carbon monoxide
detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon
monoxide detector as required in accordance with the above
provisions shall comply with NFPA 720 and be ANSI/UL 2042 listed
and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be
permanently mounted to the exterior of the building at a
minimum height of eight (8) feet above grade directly in line with
the exhaust vent terminal for the horizontally vented gas fueled
heating appliance or equipment. The sign shall read, in print
size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY
BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
4. INSPECTION. The state or local gas inspector of the side wall
horizontally vented gas fueled equipment shall not approve
the installation unless, upon inspection, the inspector observes
carbon monoxide detectors and signage installed in accordance
with the provisions of 248 CMR 5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248
CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled “Equipment Not
Required To Be Vented” in the most current edition of NFPA 54 as
adopted by the Board; and
2. Product Approved side wall horizontally vented gas fueled
equipment installed in a room or structure separate from the
dwelling, building or structure used in whole or in part for
residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING
SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment
provides a venting system design or venting system
components with the equipment, the instructions provided
by the manufacturer for installation of the equipment and the
venting system shall include:
1. Detailed instructions for the installation of the venting system
design or the venting system components; and
2. A complete parts list for the venting system design or venting
system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING
SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled
equipment does not provide the parts for venting the flue
gases, but identifies “special venting systems”, the following
requirements shall be satisfied by the manufacturer:
1. The referenced “special venting system” instructions shall
be included with the appliance or equipment installation
instructions; and
2. The “special venting systems” shall be Product Approved by
the Board, and the instructions for that system shall include a
parts list and detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved
side wall horizontally vented gas fueled equipment, all venting
instructions, all parts lists for venting instructions, and/or all
venting design instructions shall remain with the appliance or
equipment at the completion of the installation.
(3) After NFPA-54 section 10.10.4.2 add a new section 10.10.4.3 as
follows:
When more than four gas appliances are to be vented through a
common gas vent or common horizontal vent manifold, a plan of
the proposed vent installation shall be submitted to the Inspector
and the serving gas supplier for review and approval.
Extraction from: Massachusetts Rules and Regulations
5.00: Amendments To 2002 Edition Of ANSI Z223.1-NFPA-54
16
XG0518 - 100319
Notes
XG0226 - 180904
17
Installation & Maintenance Manual
PVVEX58-200
PVVEX510-300
Roof Power Vent
XG0518 - 100319
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising