Honeywell | 1103 Low Capacity Torque Transducer | Datasheet | Honeywell 1103 Low Capacity Torque Transducer Datasheet

Honeywell 1103 Low Capacity Torque Transducer Datasheet
Model 1103
Low Capacity Torque Sensor
DESCRIPTION
A line of low capacity rotary slip ring torque sensors primarily
designed for fractional horsepower motor test applications. Instrumental in monitoring start up, running, and stall torque levels
during development and qualification of these motors. Capacity
range from 10 in-oz to 20 in-oz for small shaft mounting configurations.
FEATURES
•
10 in-oz and 20 in-oz capacities
•
0.05 % non-linearity and hysteresis
•
Lower cost for general “in-line” applications
•Can be used with almost all existing dc and ac signal
conditioning equipment
•
Manual brush lifter (standard)
Model 1103
PERFORMANCE SPECIFICATIONS
Characteristic
Measure
Torque range
10, 20 oz-in
Non-linearity
±0.05 % of rated output
Hysteresis
±0.05 % of rated output
Repeatability
±0.05 % of rated output
Output @ rated capacity
±0.95 mV/V (nominal)
ENVIRONMENTAL SPECIFICATIONS
Characteristic
Measure
Temperature, operating
-29 °C to 93 °C [-20 °F to 200 °F]
Temperature, compensated
21 °C to 77 °C [70 °F to 170 °F]
Temperature effect, zero
±0.002 % of rated output/°F
Temperature effect, output
±0.002 % of reading/°F
TYPICAL SYSTEM DIAGRAM
Customer Supplied
Chart Recorder
Alarm Panel
Data Acquisition
Computer
PLC
In-Line Amplifiers
(Used with unamplified units only)
Output
Amplifier
Universal In-Line Amplifiers
+/-5 VDC
UV
+/-10 VDC
UV-10
0 +/-5 VDC
UBP
4-20mA (3 wire)
U3W
4-20mA (2 wire)
U2W
DIN rail Mount In-Line Amplifiers
0 +/- 5 VDC (3 wire)
DV-05
4-20mA (3 wire)
DA-05
0 +/- 10 VDC (3 wire)
DV10
Power Supply
Honeywell
For long cable runs or electrically
noisy environments an amplified
sensor or locally mounted amplifier
is often preferred
In-Line Amplifier
Output
Input
Serial Number
11540 Optional
Calibration Arm
2003.1 lb.
L1 L2 L3 L4
OR
VALUE
CLEAR
UP
DOWN
SETUP
CHAN
TARE
ENTER
EXIT
MODEL 1103
Display Units
OR
OR
SC500
SC2001
GM
7541
SC2000
SC3004
NK
7558
Lebow Products
ELECTRICAL SPECIFICATIONS
Characteristic
Measure
Excitation (maximum)
20 Vdc or Vac RMS
Insulation resistance
> 5000 mOhm @ 50 Vdc
Bridge resistance
240 ohm (nominal)
Number of bridges
1
Zero balance
±1.0 % of rated output
Electrical termination
PT02E-10-6P
2 Honeywell • Sensing and Control
MENU
VIEW
TEST
HH
7561-PSD
MODEL 7541
TARE
HOLD
ESC
RESET
ENTER
Mating Connectors & Cables
023-LW181-023-LF Mating Connector
7205-76-XX* Mating connector & 6 conductor cable
(unamplified unit with sense leads but not shunt cal)
7205-75-XX** Mating connector & 4 conductor cable
(unamplified unit without sense leads but not shunt cal)
7205-83-XX* Mating connector & 6 conductor cable
(for connection to instrument 7541)
7205-82-XX** Mating connector & 4 conductor cable
(for connection to instrument 7541)
* XX represents length in feet
** XX represents length in feet
100ft maximum
20ft maximum
Low Capacity Torque Sensor
MECHANICAL SPECIFICATIONS
oz-in
N-m
Max
speed
RPM
Overload capacity
(% of nominal
capacity)
Torsional
stiffness
lb-in/rad
Rotating
inertia
lb-in sec2
Weight
(lb)
10
0.07
20000
150
112
2.59 x 10-5
0.75
20
0.15
20000
150
113
2.59 x 10-5
0.75
MOUNTING DIMENSIONS
C
cm [in]
L
cm [in]
N
cm [in]
P
cm [in]
U
cm [in]
K
cm [in]
A
cm [in]
B
cm [in]
D
cm [in]
E
cm [in]
F
cm [in]
H
cm [in]
10,16
[4.00]
7,30
[2.88]
1,43
[0.56]
3,81
[1.50]
0,32
[0.12]
0,64 flat
[0.25 flat]
0,24
[0.09]
5,70
[2.25]
2,50
[1.00]
2,38
[0.94]
1,90
[0.75]
0,37
[0.14]
P
MANUAL BRUSH LIFTER
STANDARD
PTO2E-10-6P
K
A
U DIA.
H
4 MOUNTING
HOLES
D
N
N
F
F
L
E
E
B
C
For reference only
Honeywell • Sensing and Control
3
Model 1103
Low Capacity Torque Sensor
Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
Honeywell’s standard product warranty applies unless agreed
to otherwise by Honeywell in writing; please refer to your
order acknowledgement or consult your local sales office for
specific warranty details. If warranted goods are returned to
Honeywell during the period of coverage, Honeywell will repair
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
While we provide application assistance personally, through our
literature and the Honeywell web site, it is up to the customer to
determine the suitability of the product in the application.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
Find out more
Honeywell serves its customers
through a worldwide network of
sales offices, representatives
and distributors. For application
assistance, current specifica-
MISUSE OF DOCUMENTATION
• The information presented in this datasheet is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
tions, pricing or name of the
nearest Authorized Distributor,
contact your local sales office.
To learn more about Honeywell’s
test and measurement products,
call +1-614-850-5000, visit
http://measurementsensors.
honeywell.com, or e-mail inquiries to info.tm@honeywell.com
Sensing and Control
Honeywell
1985 Douglas Drive North
Golden Valley, MN 55422 USA
honeywell.com
008770-2-EN IL50 GLO
July 2014
Copyright © 2014 Honeywell International Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising