Honeywell | RF Rod End Load Cell | Datasheet | Honeywell RF Rod End Load Cell Datasheet

Honeywell RF Rod End Load Cell Datasheet
Model RF
Rod End In-line Tension Load Cell
DESCRIPTION
Model RF, with female threads, is a high output rod end load cell
The optional high output signal offers resistance to electrical
designed to be mounted inline to the load axis to measure ten-
noise as well as additional signal resolution. Additional options
sion. The outputs for these load cells are ±5 Vdc or 10 Vdc, or
include an internal buffered shunt calibration circuit for ease of
4 mA to 20 mA (two wire) all calibrated in tension. The mount-
setup with an associated indicator, and a variety of thread selec-
ing thread configurations and the all welded stainless steel
tions, including metric sizes.
construction make these tension load cells ideal for a variety of
rugged field applications as well as in the laboratory.
FEATURES
•
2000 lb to 200000 lb range
•
Female/female threads
•
Stainless steel, all-welded construction
•
0 Vdc to 5 Vdc or 4 mA to 20 mA outputs
•
Up to 0.15 % linearity
•
CE approved10
Model RF
PERFORMANCE SPECIFICATIONS
MECHANICAL SPECIFICATIONS
Characteristic
Measure
Characteristic
Measure
Load ranges12
2000 lb to 200000 lb
Maximum allowable load
150 % FS1
Linearity
100 lb to 1000 lb
±0.2 % full scale
Weight
See table
Linearity
2000 lb to 50000 lb
Material
Stainless steel
±0.15 % full scale
Deflection full scale
See table
Linearity
75000 lb to 20000 lb
Natural frequency
See table
±0.2 % full scale
Hysteresis
100 lb to 1000 lb
±0.2 % full scale
Hysteresis
2000 lb to 50000 lb
±0.15 % full scale
Hysteresis
75000 lb to 20000 lb
±0.2 % full scale
Non-repeatability
± 0.05 % full scale
Output
2 mV/V
Operation
Tension
Resolution
Infinite
ENVIRONMENTAL SPECIFICATIONS
Characteristic
Measure
Temperature, operating
-54 °C to 121 °C [-65 °F to 250 °F]
Temperature, compensated
15 °C to 71 °C [60 °F to 160 °F]
Temperature effect, zero
0.005 % full scale/°F
Temperature effect, span
0.005 % full scale/°F
ELECTRICAL SPECIFICATIONS
Characteristic
Measure
Strain gage type
Bonded foil
Excitation (calibration)
10 Vdc
Excitation (acceptable)
Up to 15 Vdc or Vac
Insulation resistance
5000 mOhm @ 50 Vdc
Bridge resistance (tolerance)
350 ohm
Zero balance (tolerance)
±1% full scale
Shunt calibration data
RANGE CODES
Range
Code
Available ranges Range
Code
Available ranges
DL
2000 lb
EL
20000 lb
DN
3000 lb
EN
30000 lb
DP
4000 lb
EP
50000 lb
DR
5000 lb
ER
75000 lb
DT
75000 lb
ET
100000 lb
DV
10000 lb
FJ
150000 lb
EJ
15000 lb
FL
200000 lb
WIRING CODES
Connector
Unamplified (Std.)
A
(+) excitation
B
(+) excitation
C
(-) excitation
D
(-) excitation
E
(-) output
F
(+) output
DEFLECTIONS AND RINGING FREQUENCIES
Capacity (lb)
Deflection at
full scale mm
[in]
Ringing frequency (Hz)
Weight kg
[lb]
2000
0,076 [0.003]
5000
0,58 [1.3]
3000
0,076 [0.003]
5000
0,58 [1.3]
4000
0,076 [0.003]
5100
0,58 [1.3]
Included
5000
0,076 [0.003]
5200
0,58 [1.3]
Electrical termination (std)
2000 lb to 50000 lb
PTIH-10-6P or equivalent (hermetic
stainless)
7500
0,076 [0.003]
8000
0,72 [1.6]
Electrical termination (std)
75000 lb to 200000 lb
MS3102E-14S-6P or equivalent
10000
0,076 [0.003]
8500
0,72 [1.6]
15000
0,076 [0.003]
9000
0,72 [1.6]
Mating connector (not included) 2000 lb to 50000 lb
PT06A-10-6S or equivalent (AA111)
20000
0,102 [0.004]
9000
0,77 [1.7]
30000
0,102 [0.004]
8000
1,58 [3.5]
50000
0,127 [0.005]
8000
1,67 [3.7]
75000 to
100000
0,152 [0.006]
3500
18,00 [39.7]
150000 to
200000
0,178 [0.007]
3000
33,02 [72.8]
Mating connector (not
included) 75000 lb to
200000 lb
MS3106A-14S-6S or equivalent (AA121)
2 Honeywell • Sensing and Control
Rod End In-Line Tension Load Cell
INTERNAL AMPLIFIERS
Amplifier
specifications
Voltage output:
Option 2b
Voltage output:
Option 2c
Voltage output:
Option 2t
Current threewire: Option 2j
Current twowire: Option 2k
Intrinsically safe
amp: Option 2n
(2N)***
Output signal
±5 V
0 V to 5 V or ±5 V
@ 45 mA
0 V to 10 V or ±10
V @ 45 mA
4 mA to 20 mA
4 mA to 20 mA
4 mA to 20 mA
Input power
(voltage)
±15 V or 26 Vdc to
32 Vdc
11 Vdc to 28 Vdc
15 Vdc to 28 Vdc
22 Vdc to 32 Vdc
15 Vdc to 40 Vdc
9 Vdc to
28 Vdc
Input power
(current)
45 mA
40 mA
40 mA
65 mA
4 mA to 28 mA
4 mA to 24 mA
Freq. resp
(amp)
3000 Hz
3000 Hz
3000 Hz
2500 Hz
300 Hz
2000 Hz
Power supply
rej.
60 db
60 db
60 db
60 db
60 db
60 db
Operating
temp.
-20 °F to 185 °F
-20 °F to 185 °F
-20 °F to 185 °F
0 °F to 185 °F
0 °F to 185 °F
-20 °F to 185 °F
Reverse
voltage
protection
Yes
Yes
Yes
Yes
Yes
Yes
Short cir.
protection
Momentary
Momentary
Momentary
Yes
Yes
Yes
Wiring code:
connector
(std)5
A (+) Supply
B Output common
C Supply return
D (+) Output
E Shunt cal 1
F Shunt cal 2
A (+) Supply
B Output common**
C Supply return **
D (+) Output
E Shunt cal 1
F Shunt cal 2
A (+) Supply
B Output common**
C Supply return**
D (+) Output
E Shunt cal 1
F Shunt cal 2
A (+) Supply
B Output common**
C Supply return**
D (+) Output
E Shunt cal 1
F Shunt cal 2
A (+) Supply
B No connection
C No connection
D (+) Output
E Case ground
F No connection
A (+) Supply
B No connection
C No connection
D (+) Output
E Case ground
F No connection
Wiring code:
cable5,6,7
R (+) Supply
Bl Output common
G Supply return
W (+) Output
B Shunt cal 1
Br Shunt cal 2
R (+) Supply
Bl Output common*
G Supply return*
W (+) Output
B Shunt cal 1
Br Shunt cal 2
R (+) Supply
Bl Output common*
G Supply return*
W (+) Output
B Shunt cal 1
Br Shunt cal 2
R (+) Supply
Bl Output common*
G Supply return*
W (+) Output
B Shunt cal 1
Br Shunt cal 2
R (+) Supply
Bl (+) Output
W Case ground
R (+) Supply
Bl (+) Output
W Case ground
* Black and green wires are internally connected.
** Pins B and C are internally connected.
*** See our Web site for the most up-to-date information regarding intrinsically safe approvals, ref. #008-0547-00.
Honeywell • Sensing and Control 3
Model RF
OPTION CODES
Many range/option combinations are available in our quick-ship and fast-track manufacture programs. Please see http://
sensing.honeywell.com/TMsensor-ship for updated listings.
Load ranges
2K, 3K, 4K, 5K, 7.5K, 10K, 15K, 20K, 30K, 50K, 75K, 100K, 150K, 200K
Temperature
compensation
1a. 60 °F to 160 °F
1b. 30 °F to 130 °F
1c. 0 °F to 185 °F
1d. -20 °F to 130 °F
1e. -20 °F to 200 °F
1f. 70 °F to 250 °F
1g. 70 °F to 325 °F8
1h. 70 °F to 400 °F8
1i. -65 °F to 250 °F8
1j. 0 °C to 50 °C
1k. -20 °C to 85 °C
1m. -25 °C to 110 °C
Internal
amplifiers
2b. 4 wire, ±5 Vdc output
2c. 0 Vdc to 5 Vdc
2j. 4 mA to 20 mA (three-wire) output
2k. 4 mA to 20 mA (two-wire)12
2n (2N) 4 mA to 20 mA (two-wire) intrinsically safe12
2t. 0 Vdc to 10 Vdc output
2u. Unamplified, mV/V output
Internal amp
enhancements
3a. Input/output isolation7
3d. Remote buffered shunt calibration
Electrical
termination
6a. Bendix PTIH-10-6P (or equivalent) 6-pin, (max. 250 °F)
(ranges 50000 lb and below)
6b. MS connector MS3102E-14S-6P (mates with MS3106E14S-6), (max. 160 °F) (ranges above 50000 lb)6
6e. Integral cable: Teflon
6f. Integral cable: PVC
Shunt
calibration
8a. Precision internal resistor8
Bridge type
11a. Square bridge8
11b. Symmetrical bridge8
11c. Square and symmetrical bridge8
31a. Dual bridge
Bridge
resistance
12b. 5000 ohm (foil) (max. 250 °F)
Zero and
span
adjustment
14a. No access to zero and span adjustment
Electrical
connector
orientation
15a. Horizontal electrical exit port orientation
15b. Vertical electrical exit port orientation
15c. Radial electrical exit port orientation
15d. Connector on end of cable
Shock and
vibration
44a. Shock and vibration resistance
Interfaces
53e. Signature calibration8
53t. TEDS IEEE 1451.4 module9
4 Honeywell • Sensing and Control
6g. Integral cable: Neoprene
6h. Integral cable: Silicone
6i. Integral underwater cable
6j. 1/2-14 conduit fitting with 5 ft of 4 conductor PVC cable
6q. Integral cable: Polyurethane
6v. Phoenix connector on end of cable
Rod End In-Line Tension Load Cell
MOUNTING DIMENSIONS
Unamplified only
Amplified only
Order code
(Unamp/Amp)
D mm [in]
L1 mm [in]
A mm [in]
B mm [in]
L2 mm [in]
E mm [in]
F mm [in]
AL414/AL614
38,1 [1.50]
107,95 [4.25]
19,05 [0.75]
20,82 [0.82]
see below
49,53 [1.95]
38,1 [1.50]
AL416/AL616
44,45 [1.75]
127 [5.00]
19,05 [0.75]
20,82 [0.82]
see below
49,53 [1.95]
38,1 [1.50]
AL418/AL618
63,5 [2.50]
177,8 [7.00]
19,05 [0.75]
20,82 [0.82]
see below
49,53 [1.95]
38,1 [1.50]
THREAD SIZES AND OPTION CODES
TYPICAL SYSTEM DIAGRAM
13a
13b
13c
13d
13e
Range (lb)
1/2-20
UNF
3/4-16
UNF
7/8-14
UNF
1-14
UNF
1 1/2-12
UNF
2000 to 5000
AL414
AL414
–
–
–
7500 to
15000
–
AL416
AL416
AL416
AL418
20000
–
–
AL416
AL416
AL418
30000 to
50000
–
–
–
–
AL418
L2 mm [in]
19,05
[0.75]
24,13
[0.95]
24,13
[0.95]
25,4
[1.0]
38,1
[1.50]
NON-STANDARD RANGES - ORDER CODE AL412
Range (lb)
Thread
type
D mm [in]
L1 mm
[in]
L2 mm
[in]
75000 to
100000
2 1/2-12
UNF
114,3 [4.50]
342,9
[13.50]
88,9 [3.50]
150000 to
200000
3 1/2-8 UNF
139,7 [5.50]
457,2
[18.00]
114,3 [4.50]
Honeywell • Sensing and Control 5
Model RF
Rod End In-Line Tension Load Cell
NOTES
1.
2.
3.
4.
5.
6.
7.
8.
9. 10.
11.
12.
Allowable maximum loads – maximum load to be applied without
damage.2
Without damage - loading to this level will not cause excessive zero
shift or performance degradation. The user must consider fatigue
life for long term use and structural integrity. All structurally critical
applications (overhead loading, etc.) should always be designed
with safety redundant load paths.
Interconnecting shunt cal. 1 terminal with shunt cal. 2 terminal
provides 50 % (unamplified units), 75 % (4 mA to 20 mA three-wire
units) or 80 % (voltage amplified units) of full scale output for quick
calibration. Shunt calibration comes standard with internal amplifier option 2a, 2b, 2c, 2t and 2j.
O=Orange; Y=Yellow; B=Blue; Bl=Black; R=Red; Br=Brown;
W=White; G=Green. Color specifying cable and number or letter
specifying connector.
No mating connector necessary for cable option.
Cannot be used with options 1c, 1e, 1f, 1g, 1h, or 1i.
Only available with option 2b or 2c.
Not available with amplified option.
Consult factory for TEDS availability with amplified models.
Termination dependent; consult factory.
This unit calibrated to Imperial (non-Metric) units.
5000 ohm bridge required.
Warranty. Honeywell warrants goods of its manufacture as
being free of defective materials and faulty workmanship.
Honeywell’s standard product warranty applies unless agreed
to otherwise by Honeywell in writing; please refer to your
order acknowledgement or consult your local sales office for
specific warranty details. If warranted goods are returned to
Honeywell during the period of coverage, Honeywell will repair
or replace, at its option, without charge those items it finds
defective. The foregoing is buyer’s sole remedy and is in lieu
of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special, or
indirect damages.
While we provide application assistance personally, through our
literature and the Honeywell web site, it is up to the customer to
determine the suitability of the product in the application.
Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this printing.
However, we assume no responsibility for its use.
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
Find out more
WARNING
Honeywell serves its customers
MISUSE OF DOCUMENTATION
through a worldwide network of
• The information presented in this datasheet is for
reference only. DO NOT USE this document as product
installation information.
• Complete installation, operation and maintenance
information is provided in the instructions supplied with
each product.
sales offices, representatives
and distributors. For application
assistance, current specifications, pricing or name of the
nearest Authorized Distributor,
contact your local sales office.
To learn more about Honeywell’s
Failure to comply with these instructions could result in
death or serious injury.
test and measurement products,
call +1-614-850-5000, visit
www.honeywell.com/sensotec,
or e-mail inquiries to
info.tm@honeywell.com
Sensing and Control
Honeywell
1985 Douglas Drive North
Golden Valley, MN 55422
www.honeywell.com
008656-2-EN IL50 GLO
January 2010
Copyright © 2010 Honeywell International Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising