Honeywell | 50035271RPNR090KAAA3A11X Hall-Effect Rotary Position Sensor, Issue 1 | Installation Instruction | Honeywell 50035271RPNR090KAAA3A11X Hall-Effect Rotary Position Sensor, Issue 1 Installation Instruction

Honeywell 50035271RPNR090KAAA3A11X Hall-Effect Rotary Position Sensor, Issue 1 Installation Instruction
Installation Instructions for the
RPNR090KAAA3A11X
Hall-Effect Rotary Position Sensor
50035271
Figure 1. Mounting and Dimensional Diagram (For
Reference Only mm/[in].)
4.75 Vdc
0.25 Vdc
L
WW/YY
RPNR090KAAA3A11X
40,8
[1.61]
Ø5.3
[0.20]
50
[1,97]
27,7
[1.09]
Pinout
Channel 1
1=0V
2 = 10 Vdc to 30 Vdc Supply
3 = 0.25 Vdc to 4.75 Vdc
Channel 2
4=0V
5 = 10 Vdc to 30 Vdc
6 = 4.75 Vdc to 0.25 Vdc Output
Characteristic Curve
Channel 1
Channel 2
0.25
45
0
Angle (°)
123456
24,8
[0.98]
4,12
[0.16]
Ø6
[0.24]
45
Table 2. Specifications
Characteristic
Supply voltage:
Channel 1
Channel 2
Current consumption
Output signal delay
Accuracy
Hysteresis
Linearity
Reverse polarity protection
Operating and storage temperature range
EMC
Expected life
Protection class
Housing material
Shaft material
Mechanical end stop
63
[2.48]
5
[0.20]
Output (Vdc)
4.75
4.75
Output (Vdc)
Channel 2
Angle
Output
4.75 Vdc
L (-45°)
0°
2.5 Vdc
R (+45°)
0.25 Vdc
0.25
Sensing and Control
0.25 Vdc
4.75 Vdc
R
56
[2.20]
MOUNTING INFORMATION
Mount the sensor using the two easily accessible mounting
holes. Mounting screw tightening torque is 2,5 N m ±0,5 N m
[22.1 in lb ±4.4 in lb].
Table 1. Output Signals
Channel 1
Angle
Output
L (-45°)
0.25 Vdc
0°
2.5 Vdc
R (+45°)
4.75 Vdc
2.5 Vdc
90°
Receptacle: AMP 1-1419168-1
Mating Connector: AMP 1438199-2
249155
GENERAL INFORMATION
The RPN Series Rotary Position Sensors use a magnetically
biased, Hall-effect integrated circuit (IC) to accurately sense
rotary movement of the actuator shaft. Rotation of the actuator
shaft changes the IC’s position relative to the magnets. The
resulting flux density change is converted to a linear output.
ISSUE 1
Parameter
10 Vdc to 30 Vdc
10 Vdc to 30 Vdc
20 mA max.
3 ms approx.
±1.6%
none
±2°
yes
-40 °C to 125 °C [-40 °F to 257 °F]
200 V/m ISO 11452-3
6
30x10 cycles
IP69K DIN 40050
PA66 plastic
stainless steel
no
14
[0.55]
8,3
[0.33]
4,6
[0.18]
Ø2
[0.08]
Ø20
[0.79]
RPNR090KAAA3A11
WARNING
PERSONAL INJURY
DO NOT USE these products as safety or emergency stop
devices or in any other application where failure of the
product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARRANTY/REMEDY
Issue 1
SALES AND SERVICE
Honeywell serves its customers through a worldwide network
of sales offices, representatives and distributors. For
application assistance, current specifications, pricing or name
of the nearest Authorized Distributor, contact your local sales
office or:
E-mail: info.sc@honeywell.com
Internet: www.honeywell.com/sensing
Honeywell warrants goods of its manufacture as being free of
defective materials and faulty workmanship. Honeywell’s
standard product warranty applies unless agreed to otherwise
by Honeywell in writing; please refer to your order
acknowledgement or consult your local sales office for specific
warranty details. If warranted goods are returned to Honeywell
during the period of coverage, Honeywell will repair or replace,
at its option, without charge those items it finds defective. The
foregoing is buyer’s sole remedy and is in lieu of all other
warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special,
or indirect damages.
Phone and Fax:
Asia Pacific
+65 6355-2828
+65 6445-3033 Fax
Europe
+44 (0) 1698 481481
+44 (0) 1698 481676 Fax
Latin America
+1-305-805-8188
+1-305-883-8257 Fax
USA/Canada
+1-800-537-6945
+1-815-235-6847
+1-815-235-6545 Fax
While we provide application assistance personally, through
our literature and the Honeywell web site, it is up to the
customer to determine the suitability of the product in the
application.
Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this printing.
However, we assume no responsibility for its use.
Sensing and Control
Honeywell
1985 Douglas Drive North
Minneapolis, MN 55422
www.honeywell.com/sensing
50035271
50035271-1-EN IL50 GLO Printed in USA
October 2008
Copyright © 2008 Honeywell International Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising