Honeywell | 50066001 | Installation Instruction | Honeywell 50066001 Installation Instruction

Honeywell 50066001 Installation Instruction
Relialign™ CDI Series
Commercial Door Interlock
ISSUE 3
50066001
Installation Instructions for the
Relialign™ CDI Series
Commercial Door Interlock
Issue 3
50066001
WARRANTY/REMEDY
Honeywell warrants goods of its manufacture as being free of
defective materials and faulty workmanship. Honeywell’s standard product warranty applies unless agreed to otherwise by
Honeywell in writing; please refer to your order acknowledgement
or consult your local sales office for specific warranty details. If
warranted goods are returned to Honeywell during the period of
coverage, Honeywell will repair or replace, at its option, without
charge those items it finds defective. The foregoing is buyer’s
sole remedy and is in lieu of all other warranties, expressed
or implied, including those of merchantability and fitness for
a particular purpose. In no event shall Honeywell be liable for
consequential, special, or indirect damages.
While we provide application assistance personally, through our
literature and the Honeywell web site, it is up to the customer to
determine the suitability of the product in the application.
Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this printing.
However, we assume no responsibility for its use.
Honeywell serves its customers through a worldwide network of
sales offices, representatives and distributors. For application
assistance, current specifications, pricing or name of the nearest
Authorized Distributor, contact your local sales office or:
PERSONAL INJURY WARNING
DO NOT USE these products as safety or emergency stop
devices or in any other application where failure of the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
ELEVATOR INTERLOCK
29BR
WARNING
WARNING
Honeywell does not recommend using devices for critical
control applications where there is, or may be, a single point
of failure or where single points of failure may result in an
unsafe condition. It is up to the end-user to weigh the risks
and benefits to determine if the products are appropriate for
the application based on security, safety and performance.
Additionally, it is up to the end-user to ensure that the control
strategy results in a safe operating condition if any crucial
segment of the control solution fails. Honeywell customers
assume full responsibility for learning and meeting the
required Declaration of Conformity, Regulations, Guidelines,
etc. for each country in their distribution market.
E-mail: info.sc@honeywell.com
Internet: sensing.honeywell.com
Phone and Fax:
USA/Canada
+1-800-537-6945
International
+1-815-235-6847; +1-815-235-6545 Fax
Relialign™ CDI Series Commercial Door Interlocks are not a
sealed switch. It is not recommended to be used in the areas
where liquid or oil may splash.
RISK TO LIFE OR PROPERTY
GENERAL INFORMATION
Honeywell Relialign™ CDI Series Residential Door Interlock
switches are electromechanical devices designed for use in
swing door applications, specifically dumbwaiters, material lifts,
lifts for the mobility impaired and private residence swing-door
elevators in the USA. In Canada, the CDI is designed for use in
swing door applications, specifically dumbwaiters, material lifts,
and residential elevators, but is not designed for use in lifts for
the mobility impaired. The interlock holds the door in place and
prevents it from being opened in potentially unsafe conditions
(e.g. the elevator/lift car is not present at the door).
Featuring a custom internal solenoid control mechanism that uses
Honeywell MICRO SWITCH™ switches, the Relialign™ Series
of door interlocks may reduce complexity of the host controller,
reduce power consumption, extend solenoid life, and reduce
solenoid timeouts. CDI Series interlocks are configurable and
available in left- and right-hand versions, allowing for simplified
installation, customization, and retrofitting into current designs.
Honeywell CDI Commercial Door Interlocks comply with ASME
A17.1 & A18.1 :2010, (the safety code standards for elevator
and escalators), CAN/CSAB44, and UL104 standards. A robust
key and cam mechanism extends the life to 1 million mechanical
operations. The snap-action cam mechanism reduces adjustment
set-up time and the key engagement was designed to minimize
maintenance costs due to false alarms. The CDI Series has a
robust zinc die cast housing and cover with white powder coat
finish.
Never use this product for an application involving serious risk
to life or property without ensuring that the system as a whole
has been designed to address the risks, and that this product
is property rated and installed for the intended use within the
overall system.
Failure to comply with these instructions could result in
death or serious injury.
MOUNTING
Note mounting dimension drawings for the installation locations.
(See Figure 1). A separate mounting template provided in the
product packaging will guide the installer on how to prepare for
the installation of the switch. The switch shall be mounted only
in vertical orientation with the conduit opening up. For the switch
that use the 6-pin terminals, remove the terminal block assembly
inside the housing to reach the mounting holes. Ensure that the
terminal block is assembled back onto the housing securely using the screws, once the switch is mounted.
ADJUSTMENT
The mounting template aligns the key to the center of the opening
in the interlock housing allowing for door sag over time without
any adjustment.
WIRING INSTRUCTIONS
1.
2.
3.
4.
Sensing and Control
Honeywell
1985 Douglas Drive North
Golden Valley, MN 55422
sensing.honeywell.com
50066001-3-EN IL50 GLO Printed in Juarez, Mexico
March 2014
© 2014 Honeywell International Inc. All rights reserved.
Sensing and Control
Remove the cover by unscrewing the cover screws.
CAT5 option only – Plug the mating CAT5 connector into the
female receptacle on the CDI interlock.
Terminal Block option – Unscrew the terminal screws. Connect wires per the schematics provided on the inside of the
interlock’s cover. Torque all terminal screws with a tightening
torque of 0.5 Nm to 0.7 Nm.
Assemble back the cover. Securely tighten the four screws.
Recommended tightening torque for the cover screws is 1.99
Nm max.
Relialign™ CDI Series
Commercial Door Interlock
ISSUE 3
50066001
Relialign™ CDI Series
Commercial Door Interlock
ISSUE 3
50066001
FIGURE 1. DIMENSIONS
This page intentionally left blank.
2
Honeywell Sensing and Control
Honeywell Sensing and Control
7
Relialign™ CDI Series
Commercial Door Interlock
ISSUE 3
50066001
Relialign™ CDI Series
Commercial Door Interlock
CLEARANCE BETWEEN HOIST WAY DOORS,
LANDING SILLS, AND CAR DOOR
PERFORMANCE SPECIFICATIONS
Characteristic
Measure
Endurance life
1 million operations minimum
Operating temperature
4 °C to 38 °C [40 °F to 100 °F]
Storage temperature
-40 °C to 60 °C [-40 °F to 140 °F]
Standards/approvals
cULus listed per UL 104
Complies with ANSI/ASME A17.1, A18.1
Complies with CAN/CSA B44
The clearance between the hoistway doors or gates and the
hoistway edge of the landing sill shall not exceed 75 mm [3 in].
The distance between the hoistway face of the landing door or
gate and the car door or gate shall not exceed 125 mm [5 in].
(See Figure 2).
CAR DOOR
(OR GATE)
5 in max.
R
CDI Series
Relialign™
Commerical
Door Interlock
L
Left
R
Right
ac/dc
1
S
Solenoid
Type
B
A.
INTERLOCK
B.
Wiring
W
Color
Connector
P
Parallel
1
Terminal strip
S
Series
2
RJ-45 Category 5
connector
3
Other
4
RJ-45 Category 5 no solenoid switch
5
Terminal strip no solenoid switch
W
White
Specials
Two characters,
letters or numbers
to signify
customer name or
other unique features
of the product not
covered in the
nomenclature.
This field is
not required.
3 in max.
EDGE OF
LANDING SILL
FIGURE 3. WIRING SCHEMATIC
PARALLEL CONNECTION
(CAT 5 CONNECTOR)
FIGURE 4. WIRING SCHEMATIC
PARALLEL CONNECTION
(6-PIN TERMINAL)
FIGURE 5. CAT 5 CONNECTOR
PIN DETAILS
7
5
PIN #1
3
DOOR CLOSED
5
PIN #8
DOOR CLOSED
4
1
SOLENOID CONTROL
2
SOLENOID
DOOR LOCKED
6
-
SOLENOID CONTROL
2
3
SOLENOID
-
DOOR LOCKED
6
FIGURE 6. WIRING SCHEMATIC
SERIES CONNECTION (CAT5 CONNECTOR)
FIGURE 7. WIRING SCHEMATIC
SERIES CONNECTION (4-PIN TERMINAL)
7
C
8
3
2
Honeywell Sensing and Control
D.
The actuator key for the switch MUST move freely without
jamming during operation
The alignment of the key to the switch MUST be checked as
per the mounting template
Visually ensure that no mechanical damage has occurred
to the switch body or key. If damage is found the complete
switch assembly MUST be replaced
Test the switch for correct electrical operation while installed
and operated normally
LANDING
DOOR
MAXIMUM CLEARANCES ACCORDING
TO ASME A17.1, CLAUSE 5.3.1.7.2
8
6
Strict compliance with installation instructions / mounting template is essential for safety. It is the customer’s responsibility to
ensure they are followed. It is imperative any wear on the actuator
key or on the switch itself are identified at an early stage and the
necessary corrective actions implemented (replacement), thus
ensuring safety.
C.
B
Key Entry
Position
Switch Type
IMPORTANT NOTICE
GENERAL DIRECTIONS
RELIALIGN™ CDI SERIES NOMENCLATURE
CDI
50066001
FIGURE 2. CLEARANCE
0.20 A max., 24 Vdc
0.35 A max., 24 Vac, 60 Hz
Electrical rating
ISSUE 3
DOOR CLOSED
D
DOOR LOCKED
B
SOLENOID CONTROL
SOLENOID
-
A
DOOR CLOSED
DOOR LOCKED
SOLENOID CONTROL
SOLENOID
-
Honeywell Sensing and Control
3
.500
2.025
1.200
Honeywell Relialign™
R
ELEVA
ATOR
INTERLLOCK
MOUN
NTING
TEMPLLATE
INTERLOCK
MOUNTING
TEMPLATE
VERIFY OUTLINE
AREA ALIGNS WITH
POSITION OF
INTERLOCK BEFORE
DRILLING HOLES.
STEP 4
LOCATION FOR
EMERGENCY
OVERRIDE
OPENING.
USE Ø 0.625
DRILL
RECOMMENDE
ED DISTANCE
BETWEEN TOP OF SWITCH
AND BOTTOM
M OF DOOR
HEADER. FIELD
CONDITIONS MAY VARY.
.500
INTERLOCK
MOUNTING
TEMPLATE
STEP
P1
CENTER PUN
NCH HOLE
LOCATIO
ON FOR
INITIAL MOUNTING
(2 PLACES)
8.250
8.250
FOLD LINE (PLACE IN CORNER OF DOOR JAMB)
TEMPLATE FOR
LEFT HAND
INTERLOCK
FOLD LINE (PLACE IN CORNER OF DOOR JAMB)
FOLD LINE
2.025
1.200
FOLD LINE
TEMPLATE FOR
RIGHT HAND
INTERLOCK
VERIFY OUTLINE
AREA ALIGNS WITH
POSITION OF
INTERLOCK BEFORE
DRILLING HOLES.
1.600
1.600
9.75
9.75
STEP 2
CENTER PUNCH
HOLE LOCATION
(2 PLACES)
1.150
1.150
KEY
MOUNTING
TEMPLATE
3.500
2.5
STEP 4
LOCATION FOR
EMERGENCY
OVERRIDE
OPENING.
USE Ø 0.625
DRILL
KEY
ENTRY
1.750
.375
.59
STEP
P3
ADD COR
RNER
SCREWS AFTER
A
ADJUSTM
MENTS.
(4 PLACES)
KEY
MOUNTING
TEMPLATE
.59
.902
.260
3.500
2.5
KEY
ENTRY
1.750
.375
ALL DIMEN
NSIONS
ARE IN IN
NCHES
SCALE
E 1:1
.375
STEP 2
CENTER PUNCH
HOLE LOCATION
(2 PLACES)
.375
.260
.902
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising