Honeywell | 50069443RTY Series Hall-Effect Rotary Position Sensors | Installation Instruction | Honeywell 50069443RTY Series Hall-Effect Rotary Position Sensors Installation Instruction

Honeywell 50069443RTY Series Hall-Effect Rotary Position Sensors Installation Instruction
Installation Instructions for the
RTY Series Hall-Effect Rotary Position Sensor
GENERAL INFORMATION
The RTY Series uses a magnetically biased, Hall-effect integrated
circuit (IC) to sense rotary movement of the actuator shaft over a
set operating range. Rotation of the actuator shaft changes a magnet’s position relative to the IC. The resulting flux density change is
converted to a linear output.
Issue 4
50069443
MOUNTING INFORMATION
Mount the sensor and/or lever using flat washers and screws as
shown in Figures 1 and 2.
In harsh applications, treat the screw threads with a suitable
thread locking compound.
Table 1. Specifications
ParameterL
Characteristic
Supply voltage
Supply current
Supply current (during
output to ground short)
Output:
standard
inverted2
Output signal delay
Overvoltage protection
Reverse polarity protection
Output to ground short
circuit protection
Output load resistance
(pull down to ground)
EMI:
radiated immunity
conducted immunity
EMC
Operating temp. range
Storage temperature range
Ingress protection
Expected life
Media compatibility
Housing material
Shock1
LV (Low Voltage) LV
5 ±0.5 Vdc
20 mA max.
HV (High Voltage) L
10 Vdc to 30 Vdc
32 mA max.
25 mA max.
47 mA max.
0.5 Vdc to 4.5 Vdc ratiometric
4.5 Vdc to 0.5 Vdc ratiometric
0.5 Vdc to 4.5 Vdc non-ratiometric
4.5 Vdc to 0.5 Vdc non-ratiometric
4 ms typ.
10 Vdc
-10 Vdc
-30 Vdc
continuous
10 kOhm typ.
100 m/V per ISO11452-2 from 200 MHz to 1000 MHz
100 m/V per ISO11452-2 from 200 MHz to 1000 MHz
100 mA BCI per ISO11452-4 from 1 MHz to 200 MHz 100 mA BCI per ISO11452-4 from 1 MHz to 400 MHz
exceeds CE requirements
-40 °C to 125 °C [-40 °F to 257 °F]
-40 °C to 125 °C [-40 °F to 257 °F]
IP67 according to DIN 40050
35 M cycles
heavy transportation fluids
PBT plastic
Vibration1
Salt fog
Resolution
Mating connector
Mechanical end stop
Approvals
50 G peak
20 G peak tested from 10 Hz to 2000 Hz
coconcentration 5% ±1% for 240 hr per SAE M1455 Section 4.3.3.1
(at 5.0 Vdc, 38 °C [100 F °])
12 bit
AMA AMP Superseal 282087-1
no
CE
1
Applies to RTY sensor without lever only.
2
Removes the requirement for the customer to have to invert the logic associated with the application. This is a convenience for the customer,
and in some cases, can simplify the customer’s overall solution.
Sensing and Control
RTY Series Hall-Effect Rotary Position Sensor
ISSUE 4
50069443
Table 2. Output
B
A
Standard Output
C
Inverted Output
A = Left output: 0.5 Vdc
A = Left output: 4.5 Vdc
B = Zero reference
B = Zero reference
C = Right output: 4.5 Vdc
C = Right output: 0.5 Vdc
Table 3. Pinout
North American
European
Pin 1 = Vcc
Pin 1 = GND
Pin 2 = GND
Pin 2 = Vcc
Pin 3 = Output
Pin 3 = Output
Notice
Ferrous material or more than 300 Gauss magnet within a 10 mm
[0.39 in] radius of sensor may affect sensor performance.
2
Honeywell Sensing and Control
RTY Series Hall-Effect Rotary Position Sensor
ISSUE 4
50069443
Table 4. Functional Characteristics
Accuracy
Error
50°
(±25°)
60°
(±35°)
70°
(±35°)
90°
(±45°)
Standard Input
Clamp High
4.5
Clamp High
4.5
2.5
0.5
Clamp Low
0.0
120°
(±60°)
A
-25
-30
-35
-45
-60
-90
-135
180°
(±90°)
270°
(±135°)
±1.0%
Inverted Input
Output Voltage (Vdc)
Linearity
Error
Output Voltage (Vdc)
Sensing
Angle
±1.6%
0.5
Clamp Low
0.0
B
C
0
0
0
0
0
0
0
+25
+30
+35
+45
+60
+90
+135
Actuator Position (°)
Output Voltage (Vdc)
Output Voltage (Vdc)
2.5
0.5
0.0
A
B
C
-25
-30
-35
-45
-60
-90
-135
0
0
0
0
0
0
0
+25
+30
+35
+45
+60
+90
+135
A
B
C
-180
0
+180
Actuator Position (°)
4.5
4.5
360°
(±180°)
2.5
A
-180
B
C
0
+180
Actuator Position (°)
2.5
0.5
0.0
Actuator Position (°)
• See table 2 for A, B, C references.
• The linearity error is the deviation of the measured value from the best fit line and is the quotient of the measured output ratio
deviation from the best fit line at the measured temperature to the best fit line output ratio span at the measured temperature.
• Accuracy is measured as a deviation from the index line, where the index line is defined as the line with the ideal slope and
sensor output voltage corrected at 0º position for its ideal value at 25 °C ±5 °C. Accuracy is valid only when the sensor output is
correct at 0º position for its ideal value in the application.
Honeywell Sensing and Control
3
RTY Series Hall-Effect Rotary Position Sensor
Figure 1. Dimensional Drawings for Sensor with Lever (For reference only: mm [in])
5,35
[0.21]
8,3
[0.33]
22,0
[0.87]
10,0
5,00 [0.39]
[0.20]
37.0
[1.46]
B
9,5
[0.37]
13,8
[0.54]
15,7
[0.62]
14,0
[0.55]
C
A
Mount sensor with non-magnetic stainless steel M5 screws. Mounting torque is 2,5 ± 0,5 N m [22.1 ±4.4 in-lb].
B
Mounting surface.
C
Mating connector: AMP superseal 282087-1.
D
Mount lever using M6x1 screws. Mounting torque 8 N m [70.8 in-lb] max.
4
Honeywell Sensing and Control
40,0
[1.57]
15,0
[0.59]
D
A
26,0
[1.02]
50069443
22,0
[0.87]
55
[2.17]
36,4
[1.43]
ISSUE 4
RTY Series Hall-Effect Rotary Position Sensor
ISSUE 4
50069443
Figure 2. Dimensional Drawings for Sensor without Lever (For reference only: mm [in])
5,35
[0.21]
22,0
[0.87]
40,0
[1.57]
5,3
[0.21]
8,3
[0.33]
37.0
[1.46]
36,4
[1.43]
15,50
[0.61]
55
[2.17]
3 2 1
A
B
9,5
[0.37]
13,8
[0.54]
26,0
[1.02]
15,6
[0.61]
1
6,00
[0.24]
2
3
C
25
[0.98]
4,12
[0.16]
A
Mount sensor with non-magnetic stainless steel M5 screws. Mounting torque is 2,5 ± 0,5 N m [22.1 ±4.4 in-lb].
B
Mounting surface.
C
Mating connector: AMP superseal 282087-1.
Honeywell Sensing and Control
5
RTY Series Hall-Effect Rotary Position Sensor
WARNING
PERSONAL INJURY
DO NOT USE these products as safety or emergency stop
devices or in any other application where failure of the product
could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARRANTY
Honeywell warrants goods of its manufacture as being free of
defective materials and faulty workmanship. Honeywell’s standard
product warranty applies unless agreed to otherwise by Honeywell
in writing; please refer to your order acknowledgement or consult
your local sales office for specific warranty details. If warranted
goods are returned to Honeywell during the period of coverage,
Honeywell will repair or replace, at its option, without charge those
items it finds defective. The foregoing is buyer’s sole remedy
and is in lieu of all warranties, expressed or implied, including
those of merchantability and fitness for a particular purpose.
In no event shall Honeywell be liable for consequential,
special, or indirect damages.
E-mail: info.sc@honeywell.com
Internet: sensing.honeywell.com
Phone and Fax:
Asia Pacific
+65 6355-2828
+65 6445-3033 Fax
Europe
+44 (0) 1698 481481
+44 (0) 1698 481676 Fax
Latin America
+1-305-805-8188
+1-305-883-8257 Fax
USA/Canada
+1-800-537-6945
+1-815-235-6847
+1-815-235-6545 Fax
Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this printing.
However, we assume no responsibility for its use.
Honeywell Sensing and Control
1985 Douglas Drive North
sensing.honeywell.com
50069443
SALES AND SERVICE
Honeywell serves its customers through a worldwide network
of sales offices, representatives and distributors. For application
assistance, current specifications, pricing or name of the nearest
Authorized Distributor, contact your local sales office or:
While we provide application assistance personally, through our
literature and the Honeywell web site, it is up to the customer to
determine the suitability of the product in the application.
Golden Valley, MN 55422
ISSUE 4
50069443-4-EN
October 2013
© 2013 Honeywell International Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising