Honeywell | CSN Series Closed Loop Current Sensors | Installation Instruction | Honeywell CSN Series Closed Loop Current Sensors Installation Instruction

Honeywell CSN Series Closed Loop Current Sensors Installation Instruction
PK XP-4062
Issue 1
Installation instructions for CSN Series
Closed loop linear current sensors
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency stop devices, or in any other application
where failure of the product could result in personal
injury.
Failure to comply with these instructions could
result in death or serious injury.
CAUTION
•
Electrical – Do not exceed maximum supply voltage
ratings. Do not reverse the supply voltage polarity.
Ensure your power supply is sufficiently rated to
provide current for the sensor operation plus the
sensor output current.
• Handling – Sensors intended for PCB mounting
should be handled with care to avoid damaging
solder terminals.
• Isolation – Sensors that do not include an integral
primary circuit (e.g. a busbar) have a rated insulation
voltage that is relative only to the primary conductor
aperture of the sensor. Sensors with an integral
primary circuit have a rated insulation voltage that is
relative only to that integral circuit.
Failure to comply with these instructions may
result in product damage.
General description
The CSN Series of closed loop current sensors are based
on the principles of the Magnetoresistive or Hall effects,
and the null balance or zero magnetic flux method
(feedback system). The magnetic flux in the sensor core
is constantly controlled at zero. The amount of current
required to balance zero flux is the measure of the
primary current flowing through the conductor, multiplied
by the ratio of the primary to secondary windings. This
closed loop current is the output from the device and
presents an image of the primary current reduced by the
number of secondary turns at any time. This current can
be expressed as a voltage by passing it through a
resistor.
Interface details
Soldering – Sensors intended for PCB mounting are
compatible with wave soldering methods. Select soldering
parameters for your system to provide optimum solder
conditions. Guidance available on request. The PCB
requires rigid support during wave soldering.
Mechanical – Please refer to the ‘M’ (mounting) drawing
and technical data sheet associated with the listing in
question for appropriate details on non-soldered
connections. Drawings and datasheets are available from
our website, www.honeywell.com/sensing.
Mounting
The CSN Series of closed loop current sensors has a
wide variety of mounting styles available. Please refer to
the ‘M’ (mounting) drawing associated with the listing in
question for appropriate details on mounting
arrangements and dimensions. Mounting drawings are
available from our website, www.honeywell.com/sensing.
Cleaning
Proper cleaning fluids should be selected based on the
type of contaminants to be removed. Honeywell
recommends alcohols, chlorinated solvents and
fluorinated solvents.
Sensing and Control
PK XP-4062
CSN Series
Issue 1
Electrical connections
CSN Series of closed loop current sensors are connected as follows, depending on whether a bipolar (+/-) or unipolar
(+/0) power supply is required by the sensor:
+V
+
-V
-
Sensor using
bipolar power
supply
+V
+
0V
0 V
O/P
O/P
0V
Sensor using
unipolar power
supply
OUTPUT
OUTPUT
REF
Measuring resistor
Warranty/Remedy
Honeywell warrants goods of its manufacture as being
free of defective materials and faulty workmanship.
Contact your local sales office for warranty information. If
warranted goods are returned to Honeywell during the
period of coverage, Honeywell will repair or replace
without charge those items it finds defective. The foregoing is Buyer’s sole remedy and is in lieu of all other
warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose.
Specifications may change without notice. The information we supply is believed to be accurate and reliable as
of this printing. However, we assume no responsibility for
its use.
While we provide application assistance personally,
through our literature and the Honeywell web site, it is up
to the customer to determine the suitability of the product
in the application.
Sensing and Control
www.honeywell.com/sensing
Honeywell Control Systems Ltd
Newhouse Industrial Estate
Motherwell, Lanarkshire ML1 5SB
Scotland, UK
PK XP-4062 Issue 1 UK07 GLO 06/04
Copyright 2004 Honeywell International Inc. All Rights Reserved.
For application assistance, current specifications or
name of the nearest Authorized Distributor, check the
Honeywell web site or call:
Telephone:
International
1-800-537-6945
USA/Canada
1-815-235-6847
United Kingdom
+44 (0)1698 481 481
France
+33 1 60 19 80 40
Germany
+49 69 8064 444
Asia Pacific
+65 6355-2828
FAX:USA
1-815-235-6545
Internet:
www.honeywell.com/sensing
E-mail:
info.sc@honeywell.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising