Honeywell | FSA Series | Installation Instruction | Honeywell FSA Series Installation Instruction

Honeywell FSA Series Installation Instruction
Installation Instructions for the
Honeywell Force Sensors
FSA Series Compensated/Amplified
32311097
Issue B
Table 1. Operating Specifications
Analog
Digital
Characteristic
Unit
Supply voltage (Vsupply):
3.3 Vdc
5.0 Vdc
Min.
Typ.
Max.
Min.
Typ.
Max.
3.0
4.75
3.3
5.0
3.6
5.25
3.0
4.75
3.3
5.0
3.6
5.25
Vdc
—
—
2.0
2.6
—
—
—
—
2.8
3.9
3.9
4.6
mA
1, 2, 3
Supply current:
3.3 Vdc
5.0 Vdc
13
Power input
20
mW
Operating temperature range4
0 [32]
—
70 [158]
0 [32]
—
70 [158]
°C [°F]
Compensated temperature range5
5 [41]
—
50 [122]
5 [41]
—
50 [122]
°C [°F]
-40 [-40]
—
85 [185]
-40 [-40]
—
85 [185]
°C [°F]
Startup time (power up to data ready)
—
—
5
—
—
3
ms
Response time
—
1
—
—
0.42
0.84
ms
—
2.5
—
—
97.5
—
—
—
—
—
—
—
%Vsupply
—
—
—
—
—
—
—
80
—
—
20
—
%Vsupply
Pull up on SDA/MISO, SCL/SCLK, SS
—
—
—
1
—
—
kOhm
Accuracy6
—
—
±3
—
—
±3
%FSS7 BFSL
Total Error Band8
—
—
±5
—
—
±5
%FSS
Output resolution
—
—
—
12
—
—
bits
Long term stability9
—
±1.3
—
—
±1.3
—
%FSS
Storage temperature range
Clipping limit:
upper
lower
SPI/I2C voltage level:
low
high
Sensors are either 3.3 Vdc or 5.0 Vdc based on the catalog listing selected.
2
Ratiometricity of the sensor (the ability of the device output to scale to the supply voltage) is achieved within the specified operating voltage.
3
The sensor is not reverse polarity protected. Incorrect application of supply voltage or ground to the wrong pin may cause electrical failure.
4
Operating temperature range: The temperature range over which the sensor will produce an output proportional to force.
5
Compensated temperature range: The temperature range over which the sensor will produce an output proportional to force within the specified
performance limits.
6
Accuracy: The maximum deviation in output from a Best Fit Straight Line (BFSL) fitted to the output measured over the force range at 25°C [77°F].
Includes all errors due to force non-linearity, force hysteresis, and non-repeatability.
7
Full Scale Span (FSS): The algebraic difference between the output voltage at full scale force and the output at zero force.
8
Total Error Band (TEB): Combined error from calibration, accuracy and temperature effects over the compensated temperature range at 5.0 V from
15 %FSS to 95 %FSS.
9
Long-term stability after 1000 hr of operation at 25°C [77°F].
1
Sensing and Internet of Things
Honeywell Force Sensors
FSA Series Compensated/Amplified
Issue B
32311097
Table 2. Environmental Specifications
Characteristic
Parameter
Humidity
0% to 95% RH, non-condensing
Vibration
MIL-STD-202, Method 214, Condition 1E (16.9 G)
Shock
MIL-STD-202, Method 213, Condition F (1500 G)
Life1
1
1 million full scale force cycles minimum
Life may vary depending on specific application in which the sensor is utilized.
Table 3. Materials1
Component
Material
Covers
high temperature polyamide
Plunger
stainless steel 316
Substrate
alumina, ceramic
Adhesives
epoxy, silicone
Electronic components
1
ceramic silicon, glass, solder
Contact Honeywell customer service for detailed material information.
Table 4. Absolute Maximum Specifications
Characteristic
Min.
Max.
Unit
Supply voltage
-0.3
6.0
Vdc
Voltage on any pin
-0.3
Vsupply + 0.3
V
Digital interface clock frequency:
SPI
I2C
50
100
800
400
kHz
2
—
kV
-40 [-40]
85 [185]
°C [°F]
—
6804 [15]
g [lb]
ESD susceptibility (human body model)
Storage temperature range
Overforce limit
Minimum operating voltage
Lead soldering time and temperature
2
Sensing and Internet of Things
2.8 Vdc
4 s max. at 220°C [428°F]
Honeywell Force Sensors
FSA Series Compensated/Amplified
Issue B
32311097
Figure 2. Transfer Function Limits1
Analog Version
Compensated Force Range
Output (%Vsupply)
100
90
80
70
60
Ideal
50
40
5% Total Error Band
30
20
10
0
0
F min.
Output (V) =
1
2
3
4
5
6
7
8
9
Force (example unit)
0.8 x Vsupply
Force range
10
F max.
x (Force applied ) + 0.10 x Vsupply
Digital Version
Compensated Force Range
Output (%Vsupply)
100
90
80
70
60
50
40
30
20
10
0
Ideal
5% Total Error Band
0
F min.
1
2
3
4
6
7
Force (example unit)
Output (% of 214 counts) =
1
5
8
9
10
F max.
80%
x (Force applied ) + 10%
Force range
Transfer Function “A” is shown. See Figure 1 for other available transfer function options.
Sensing and Internet of Things
3
Honeywell Force Sensors
FSA Series Compensated/Amplified
Issue B
32311097
Figure 2. Mounting Dimensions (For reference only: mm/in.)
Analog version
25,02
[0.99]
23,57
[0.93]
ø12,70
1,79
[0.07]
[0.5]
6,11
[0.24]
3,68
[0.14]
3X 0,63
[0.02]
3X 2,54
[0.1]
17,36
[0.68]
5,74
[0.23]
5,7
[0.22]
Pin 1
3X 6,48
[0.26]
12,19
[0.48]
3X 1,31
[0.05]
Plunger
3X 0,61
[0.02]
7,1
[0.28]
2X 3,94
[0.15]
Function
Pin 1
Pin 2
Pin 3
analog
Vsupply
Vout
GND
Digital version
8,25
[0.32]
25,02
[0.99]
23,57
[0.93]
1,79
[0.07]
ø12,70
[0.5]
3,68
[0.14]
5X 0,63
[0.02]
3,57
[0.14]
4X 2,54
[0.1]
5,74
[0.23]
17,36
[0.68]
5,7
[0.22]
Pin 1
5X 6,48
[0.26]
12,19
[0.48]
5X 1,31
[0.05]
Plunger
5X 0,61
[0.02]
7,1
[0.28]
2X 3,94
[0.15]
Function
Pin 1
Pin 2
SPI
GND
GND
2
IC
4
Sensing and Internet of Things
8,25
[0.32]
Pin 3
Pin 4
Pin 5
Vsupply
SS
MISO
SCLK
Vsupply
N/C
SDA
SCL
Force Sensors
FSA Series Compensated/Amplified
Issue B
32311097
WARNING
PERSONAL INJURY
DO NOT USE these products as safety or emergency stop
devices or in any other application where failure of the
product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
Warranty/Remedy
Honeywell warrants goods of its manufacture as being free
of defective materials and faulty workmanship during the
applicable warranty period. Honeywell’s standard product
warranty applies unless agreed to otherwise by Honeywell
in writing; please refer to your order acknowledgment or
consult your local sales office for specific warranty details.
If warranted goods are returned to Honeywell during the
period of coverage, Honeywell will repair or replace, at its
option, without charge those items that Honeywell, in its sole
discretion, finds defective. The foregoing is buyer’s sole
remedy and is in lieu of all other warranties, expressed or
implied, including those of merchantability and fitness for a
particular purpose. In no event shall Honeywell be liable for
consequential, special, or indirect damages.
While Honeywell may provide application assistance personally,
through our literature and the Honeywell web site, it is buyer’s
sole responsibility to determine the suitability of the product in
the application.
Find out more
Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this writing.
However, Honeywell assumes no responsibility for its use.
Honeywell serves its customers through
a worldwide network of sales offices and
distributors. For application assistance, current
specifications, pricing or name of the nearest
Authorized Distributor, contact your local sales
office.
To learn more about Honeywell’s sensing and
switching products, call
+1-815-235-6847 or 1-800-537-6945, visit
sensing.honeywell.com, or e-mail inquiries to
info.sc@honeywell.com
Honeywell Sensing and Internet of Things
9680 Old Bailes Road
Fort Mill, SC 29707
honeywell.com
32311097-B-EN | B | 1/17
© 2017 Honeywell International Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising