Honeywell | HIH6120/6121 Seriess | Installation Instruction | Honeywell HIH6120/6121 Seriess Installation Instruction

Honeywell HIH6120/6121 Seriess Installation Instruction
Honeywell HumidIcon™ Digital
Humidity/Temperature Sensors:
HIH6120/6121 Series
GENERAL INFORMATION
The following associated literature is available on the Web:
Product data sheet
Product application note
Application sheets:
– Humidity Sensor Performance Characteristics
– Humidity Sensor Theory and Behavior
– Humidity Sensor Moisture and Psychrometrics
– Humidity Sensor Chemical Resistivity
– Thermoset Polymer-based Capacitive Sensors
Technical Notes:
2
– I C Communication with the Honeywell HumidIcon™
Digital Humidity/Temperature Sensors
– Using Alarms on the Honeywell HumidIcon™ Digital
Humidity/Temperature Sensors
– Entering and Using Command Mode on the Honeywell
HumidIcon™ Digital Humidity/Temperature Sensors
Series
– Total Error Band Specification for Honeywell Digital
Humidity/Temperature Sensors
CAUTION
IMPROPER HANDLING
Do not remove the sensor from its original protective
packaging until it is ready to be installed.
Do not touch the sensor surface. Use latex finger cots.
Handle the sensor by its package edges or leads.
Do not allow objects to enter the cavity of the sensor
element.
Do not allow debris or contaminants to accumulate on
the filter.
Failure to comply with these instructions may result in
product damage.
SOLDERING AND ASSEMBLY
CAUTION
IMPROPER CLEANING
Insert and solder the sensor after the PCB cleaning
process.
Failure to comply with these instructions may result in
product damage.
CAUTION
IMPROPER SENSOR POSITIONING
Position the sensor so that its face is exposed to the
atmosphere being monitored.
Failure to comply with these instructions may result in
product damage.
Sensing and Control
CAUTION
IMPROPER SOLDERING
For better product reliability, the HIH6120/6121 Series is
factory-shipped with a protective tape on the cover
(sensing face). This tape must remain in place during
soldering.
After soldering, remove the protective tape as described
below to activate the sensor.
Failure to comply with these instructions may result in
product damage.
PROTECTIVE TAPE REMOVAL
1. Use proper ESD protection.
2. Using covered fingers or tweezers to ensure that no debris
falls into the filter, sensor cover or die, grip the
overhanging front edge of the protective tape and peel it
back from the top surface of the sensor.
3. Ensure the complete rectangle of protective tape is
removed.
Figure 1. Protective Tape Removal
SOLDERING
Process
Automated: Use a no-clean flux. Limit the contact of the
flux to the leads only. Reflow soldering profile is specified
by J-STD-020D for a small package with a peak
temperature of 260 C [500 F].
Manual: Do not exceed 350 C [662 F] for 4 s max.
HIH6120/6121 Series
SENSOR REHYDRATION
NOTICE
SENSOR REHYDRATION
Exposure to elevated temperatures, such as those
experienced during solder reflow, may dry out the sensing
element. It is recommended that the sensor be allowed
time to rehydrate after soldering or other high
temperature/dry exposures.
Exposure to these conditions will not permanently
damage the sensor. It will generally return to its factorycalibrated value after rehydration.
If rehydration is not performed, the sensor may read a
slight offset that slowly disappears over time as the
sensor becomes exposed to ambient conditions.
Conversely, extended exposure to condensing and high
humidity environments (>90 %RH) may cause a revisable
shift in readings which will generally return to normal after
the sensor has been allowed to dry off.
50068121
Issue 2
To rehydrate the sensor, expose it to room temperature under
ambient conditions (>50 %RH) for a minimum of five hours.
MOISTURE SEALING THE LEADS
If, in the presence of intermittent moisture or other
contaminants, there is the possibility of galvanic paths between
the leads, moisture seal the leads and exposed pads.
Table 1. Environmental Specifications
Characteristic
Condition
Min.
Typ.
Max.
Operating temperature range
–
-25 [-13]
–
85 [185]
Storage temperature range
–
-40 [-40]
–
85 [185]
Storage humidity
–
30
–
50
Soldering:
automated
IPC/EIA/JEDEC J-STD-020D
–
–
260 [500]
manual
apply heat for 4 s max. for manual soldering
–
–
350 [662]
ESD
MIL-STD 883H, Method 3015.7
–
–
±4
Latch-up immunity
–
–
–
±100
Shock
MIL-STD 202G, Method 213D, Test Condition C,
half-sine, 6 ms ±3 perpendicular axis, 3 shock
–
–
100
pulses per axis
Vibration
MIL-STD 202G, Method 204D, Test Condition D,
–
–
20
10 Hz to 2000 Hz
Light sensitivity
exposed to 50 lumens yellow light; exhibited no change in output
Table 2. Humidity Performance Specifications
Characteristic
Condition
Supply voltage variation
2.3 Vdc to 5.5 Vdc
1
Compensated humidity range
–
1
Compensated temp. range
–
Resolution
14 bit ADC resolution
2
Accuracy
–
3
Total error band
–
Response time
airflow minimum 20 l/min
Operating range
non-condensing
Long term stability
50 %RH for 5 years
Impact of soldering
IPC/EIA/JEDEC J-STD-020D, peak temp. of
260 °C [500 °F]
Min.
–
10
5 [41]
–
–
–
–
0
–
–
Typ.
0.1
–
–
–
–
–
6
–
±0.05
–
Max.
0.5
90
50 [122]
0.04
±4
±5
8
100
±1.2
±2.5
Unit
°C [°F]
°C [°F]
%RH
°C [°F]
kV
mA
g
g
Unit
%RH
%RH
°C [°F]
%RH
%RH
%RH
s
%RH
%RH
%RH
Notes:
1. Conversion formulas:
14 bit ADC output for humidity to %RH:
Humidity(%RH)
Humidity_ 14 _ bit _ ADC _output
100
214 2
14 bit ADC output for temperature conversion to ºC:
Temperature( C)
Temperature _ 14 _ bit _ ADC _output
165 40
214 2
2. Accuracy is specified at the typical supply voltage of 3.3 Vdc and at 25 °C [77 °F]. It is the maximum deviation from the ideal transfer function of
relative humidity measured over the humidity range of 10 %RH to 90 %RH and includes all errors due to humidity non-linearity, humidity
hysteresis and humidity non-repeatability.
3. Total error band is the maximum deviation from the ideal transfer function of relative humidity over the compensated range of 5 °C [41 °F] to
50 °C [122 °F]. It includes all errors due to humidity non-linearity, humidity hysteresis, humidity non-repeatability, thermal effect on zero, thermal
effect on span and thermal hysteresis.
2 Honeywell
Sensing and Control
HIH6120/6121 Series
Issue 2
Table 3. Temperature Performance Specifications
Characteristic
Condition
Supply voltage variation
2.3 Vdc to 5.5 Vdc
Compensated temp. range
–
Resolution
14 bit ADC resolution
1
Accuracy (BFSL)
–
Response time
1/e slow moving air
Long term stability
25 °C for 5 years
Impact of soldering
IPC/EIA/JEDEC J-STD-020D, peak temp.
of 260 °C [500 °F]
Note:
1. Accuracy is specified over the compensated temperature range.
Table 4. Current Consumption
Characteristic
Sleep current
Supply current
VDD
3.3
3.3
Abbr.
ISLEEP
IDD
Condition
–
14 bit fastest update, no sleep
Table 5. Input and Output Characteristics
Characteristic
Abbr.
Supply voltage
VDD
Low level output voltage
VOL
High level output voltage
VOH
Low level input voltage
VIL
High level input voltage
VIH
2
I C pull-up resistor
RP
Table 6. Measurement Timing
Characteristic
Start-up time (Power-On to
data ready)
Update rate
Abbr.
TSTA
Min.
–
5 [41]
–
–
5
–
–
50068121
Typ.
0.5
–
–
–
–
–
–
Max.
1.0
50 [122]
0.025
±1.0
30
±0.05
±0.1
Unit
°C
°C [°F]
°C
°C
s
°C/yr
°C
Typ.
0.6
0.65
Max.
1
1
Unit
µA
mA
Unit
Vdc
VDD
VDD
VDD
VDD
kOhm
Unit
ms
Condition
–
IOL = 2.8 mA min.
IOH = -2.8 mA min.
–
–
–
Min.
2.3
–
80%
–
80%
–
Typ.
3.3
–
2.2
Max.
5.5
20%
–
20%
–
–
Condition
14 bit TH and 14 bit humidity resolution
Min.
–
Typ.
50
Max.
60
–
application dependent: measurements are taken only when the application requests them
2
Figure 2. I C Timing
SDA
tLOW
tSUDAT
tHDSTA
tBUS
SCL
tHDSTA
tHDDAT
Characteristic
SCL clock frequency
Start condition hold time relative to SCL edge
Minimum SCL clock low width
Minimum SCL clock high width
Start condition setup time relative to SCL edge
Data hold time on SDA relative to SCL edge
Data setup time on SDA relative to SCL edge
Stop condition setup time on SCL
Bus free time between stop and start condition
tHIGH
tSUSTO
tSUSTA
Abbr.
FSCL
tHDSTA
tLOW
tHIGH
tSUSTA
tHDDAT
tSUDAT
tSUSTO
tBUS
Min.
100
0.1
0.6
0.6
0.1
0
0.1
0.1
1
Typ.
–
–
–
–
–
–
–
–
–
Honeywell
Max.
400
–
–
–
–
-0.5
–
–
–
Unit
kHz
µs
µs
µs
µs
µs
µs
µs
µs
Sensing and Control 3
HIH6120/6121 Series
Issue 2
50068121
Figure 3. SIP 4 PIN Dimensions and Pinout (For reference only. mm/[in], shown with protective tape removed.)
Mounting
Pin ASIC Pad
1
VDD
2
VSS
3
SCL
4
SDA
Landing Pattern
Description
connect via 0.22 µF to ground
supply ground
2
I C clock
2
I C data
1,05 DIA.
[0.040]
0,65 DIA.
[0.025]
1,27
[0.050]
Tape and Reel
Honeywell
Sensing and Control 4
HIH6120/6121 Series
Issue 2
50068121
Figure 4. Typical Application Circuit
VSUPPLY = 2.3 Vdc to 5.5 Vdc
2.2
kOhm
Digital Humidity/Temp.
Sensor
1
0.22 µF
2
VDD
SCL
VSS
SDA
2.2
kOhm
3
4
GND
1
Figure 5. HIH6120/6121 Series Maximal Accuracy (Performance is specified between 10 %RH and 90 %RH.)
90
Relative Humidity (%RH)
80
70
60
50
40
30
20
10
0
±1
±1
±1
±2
±2
±2
±2
±2
±2
±2
±2
±2
±2
±2
±1
±1
±1
±2
±2
±2
±2
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
10
±2
±2
±2
±2
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±2
±2
±2
±2
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
20
±3
±3
±2
±2
±2
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±2
±2
±2
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
30
±3
±3
±2
±2
±2
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±2
±2
±2
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
40
±3
±3
±2
±2
±2
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±3
±2
±2
±1
±2
±2
±2
±2
±2
±2
±2
±2
±2
±2
±2
±1
±1
±1
50
Temperature ( C)
Note:
1. Maximal accuracy is the mean value between rising and falling RH points.
Honeywell
Sensing and Control 5
HIH6120/6121 Series
WARNING
PERSONAL INJURY
DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
The sensor’s housing does not provide electrical safety
isolation. Mount the sensor in a location where it cannot
be touched, or where a surrounding barrier prevents
human contact.
Failure to comply with these instructions could result in
death or serious injury.
WARRANTY/REMEDY
Honeywell warrants goods of its manufacture as being free of
defective materials and faulty workmanship. Honeywell’s
standard product warranty applies unless agreed to otherwise
by Honeywell in writing; please refer to your order
acknowledgement or consult your local sales office for specific
warranty details. If warranted goods are returned to Honeywell
during the period of coverage, Honeywell will repair or replace,
at its option, without charge those items it finds defective. The
foregoing is buyer’s sole remedy and is in lieu of all other
warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special,
or indirect damages.
Issue 2
SALES AND SERVICE
Honeywell serves its customers through a worldwide network
of sales offices, representatives and distributors. For
application assistance, current specifications, pricing or name
of the nearest Authorized Distributor, contact your local sales
office or:
E-mail: info.sc@honeywell.com
Internet: www.honeywell.com/sensing
Phone and Fax:
Asia Pacific
+65 6355-2828
+65 6445-3033 Fax
Europe
+44 (0) 1698 481481
+44 (0) 1698 481676 Fax
Latin America
+1-305-805-8188
+1-305-883-8257 Fax
USA/Canada
+1-800-537-6945
+1-815-235-6847
+1-815-235-6545 Fax
While we provide application assistance personally, through
our literature and the Honeywell web site, it is up to the
customer to determine the suitability of the product in the
application.
Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this printing.
However, we assume no responsibility for its use.
Sensing and Control
Honeywell
1985 Douglas Drive North
Golden Valley, MN 55422
www.honeywell.com/sensing
50068121
50068121-2-EN
March 2012
Copyright © 2012 Honeywell International Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising