Honeywell | PK 80143SR16/17 Series Hall-Effect Vane Sensors, Issue 2 | Installation Instruction | Honeywell PK 80143SR16/17 Series Hall-Effect Vane Sensors, Issue 2 Installation Instruction

Honeywell PK 80143SR16/17 Series Hall-Effect Vane Sensors, Issue 2 Installation Instruction
Installation Instructions for the
SR16/17 Series Hall-Effect Vane Sensors
WARNING
PERSONAL INJURY
•= DO NOT USE these products as safety or
emergency stop devices or in any other application
where failure of the product could result in personal
injury.
Failure to comply with these instructions could
result in death or serious injury.
ISSUE 2
PK 80143
SOLDERING/ASSEMBLY
Leads must be adequately supported during any
forming/shearing operation to ensure that the leads
are not stressed inside the plastic case. Recommended PC board wave soldering temperature is
o
o
o
o
250 C to 260 C (482 F to 500 F) for 3 seconds
maximum. Hand solder 3 to 5 seconds using 650ÛC
soldering iron and no-clean solder.
No-clean fluxes are recommended. Test for
compatibility with water-soluble fluxes and cleaning
systems.
CAUTION
SOLVENT CLEANING DAMAGE
Do NOT use solvents to clean systems. Solvent
cleaning can result in the chemical attack of the
polycarbonate sensor components.
Failure to comply with these instructions will
result in product damage.
ABSOLUTE MAXIMUM RATINGS*
Temperature range
Supply voltage
Voltage externally
applied to output
Output current
-20ÛC to +85ÛC (-4ÛF to +185ÛF)
3.8 VDC to 30 VDC
-0.5 VDC to +30 VDC
50 mA
Magnetic flux
No limit. Circuit cannot be
damaged by magnetic overdrive.
* Absolute maximum ratings are the extreme limits that the
device will withstand without damage to the device.
However, the electrical and mechanical characteristics are
not guaranteed as the maximum limits (above
recommended operating conditions) are approached, nor
will the device necessarily operate at absolute maximum
ratings.
ELECTRICAL CHARACTERISTICS –20°°C TO 85°°C, 3.8 TO 30 VDC
Min.

Max.
3.8 to 30
9
Remarks
VDC
mA (off) 10 mA (on)

0.40 V
Sinking 20 mA max.
Sink current (operated)

20
mA
Output leakage current (released)

10 µA
VOUT = 30 VDC, VCC = 24 VDC
Output switching time
Rise, 10 to 90%

1.5 µs
VCC = 12 V, RL = 1.6 KΩ, CL = 20 pF
Fall, 90 to 10%

1.5 µs
VCC = 12 V, RL = 1.6 KΩ, CL = 20 pF
Supply voltage
Current consumption
Output voltage (operated)
Operating Temperature
Sensing and Control
-20°C to +85°C (-4°F to +185°F)
SR16/17 Series Hall Effect Vane Sensors
ISSUE 2
PK 80143
BLOCK CIRCUIT WIRING DIAGRAM
Vs (+)
HALL
SENSOR
TRIGGER
CIRCUIT
AND
AMPLIFIER
OUTPUT
(O) N. H.
GROUND (-)
SPEED SENSING INTERFACE
High
Impedance
Input
Vcc +5
Vcc
Ground Black (
10 K Ohm
100 Ohm
100 Ohm
100 pF Capacitor
)
Vcc Red (+)
Input Green(O)
MOUNTING DIMENSIONS (for reference only) mm/in
SR16/17 Series Vane Sensors
SR16C-J4
2 Honeywell • Sensing and Control
For application help: call 1-800-537-6945
SR16/17 Series Hall Effect Vane Sensors
ISSUE 2
PK 80143
MOUNTING DIMENSIONS (for reference only) mm/in
SR16/17 SERIES VANE SENSORS
SR16C-J6
SR16C-N
SR17C-J6
For application help: call 1-800-537-6945
Honeywell • Sensing and Control 3
SR16/17 Series Hall Effect Vane Sensors
WARRANTY/REMEDY
Honeywell warrants goods
of its manufacture as being
free of defective materials and
faulty workmanship. Contact
your local sales office for
warranty information. If
warranted goods are returned
to Honeywell during the period
of coverage, Honeywell will
repair or replace without
charge those items it finds
defective. The foregoing is
Buyer’s sole remedy and is in
lieu of all other warranties,
expressed or implied,
including those of
merchantability and fitness
for a particular purpose.
Specifications may change
without notice. The
information we supply is
believed to be accurate and
reliable as of this printing.
However, we assume no
responsibility for its use.
While we provide application
assistance personally, through
our literature and the
Honeywell web site, it is up to
the customer to determine the
suitability of the product in the
application.
Sensing and Control
Honeywell Inc.
11 West Spring Street
Freeport, Illinois 61032
Printed with Soy Ink
on 50% Recycled Paper
PK 80143-2-EN IL50 GLO 0303 Printed in USA
www.honeywell.com/sensing
ISSUE 2
PK 80143
For application assistance,
current specifications, pricing
or name of the nearest
Authorized Distributor, contact
a nearby sales office. Or call:
1-800-537-6945 USA
1-800-737-3360 Canada
1-815-235-6847 International
FAX
1-815-235-6545 USA
INTERNET
www.honeywell.com/sensing
info.sc@honeywell.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising