Honeywell | SNDH-H Series Hall-Effect Speed Sensors | Installation Instruction | Honeywell SNDH-H Series Hall-Effect Speed Sensors Installation Instruction

Honeywell SNDH-H Series Hall-Effect Speed Sensors Installation Instruction
ISSUE 1
Installation Instructions for the
SNDH-H Series Hall-Effect Speed Sensor
GENERAL INFORMATION
The SNDH-H Series Hall-Effect Speed Sensors use a
magnetically biased Hall-effect integrated circuit to accurately
sense movement of ferrous metal targets.
Optimum performance is dependent upon variables which
must be considered in combination: target material, geometry
and speed, sensor/target gap, and environmental temperature.
50071164
INSTALLATION
Mount sensor so that the center of the sensor face is over
the center of the gear teeth or target. Ensure the mounted
sensor is stable and vibration free.
Locate sensor wires as far as possible from electrical
motors, relays, etc. Do not run sensor wires in parallel with
power cables.
Table 1. Specifications
Characteristic
Supply voltage range
Output
Supply current
Output current
Output leakage current
Reverse output voltage
Rise time (10% to 90%)
Fall time (90% to 10%)
Target orientation
Zero speed
Operating frequency
range
Operating temp. range
Dielectric
Housing material
Sensing air gap
Target tooth width
Target slot width
Tooth height
Target width
Sensor misposition to
target
Probe length
Probe diameter
Connector
SNDH-H3L-G01 SNDH-H3C-G03 SNDH-H3C-G04 SNDH-H3C-G05 SNDH-H3C-G06 SNDH-H3P-G01
4 Vdc to 24 Vdc 4.5 Vdc to 24 Vdc 6.5 Vdc to 24 Vdc
4.5 Vdc to 24 Vdc
digital current sinking (open collector)
6 mA max.
20 mA max.
14 mA max.
20 mA max.
30 mA1
20 mA sinking
10 µA
-0.5 V
400 ns
15 µs max.
1 µs
15 µs max.
400 ns
0.01 µs max.
0.6 µs
0.01 µs max.
omnidirectional
alignment
omnidirectional
required
yes
no
yes
no
0 kHz to 15 kHz 2 Hz to 15 kHz
0 kHz to 12 kHz
2 Hz to 15 kHz
6.5 Vdc to 24 Vdc
-40 °C to 100 °C -40 °C to 150 °C
[-40 °F to 212 °F] [-40 °F to 302 °F]
200 Vdc
stainless steel
up to 2,5 mm
up to 2 mm
[0.098 in]
[0.079 in]
2 mm [0.079 in] 2,5 mm [0.098 in]
may vary
2 mm [0.079 in] 5 mm [0.197 in],
constant
5 mm [0.197 in] 3 mm [0.118 in]
>3 mm
[0.118 in]
-40 °C to 125 °C
[-40 °F to 257 °F]
-40 °C to 125 °C
[-40 °F to 257 °F]
-40 °C to 150 °C
[-40 °F to 302 °F]
14 mA max.
1 µs
0.6 µs
alignment
required
yes
0 kHz to 12 kHz
plastic
up to 2,5 mm
[0.098 in]
3 mm [0.118 in]
up to 2 mm
[0.079 in]
2,5 mm [0.098 in]
may vary
>2 mm [0.079 in]
5 mm [0.197 in]
constant
>2 mm [0.079 in]
3 mm [0.118 in]
>2 mm [0.079 in]
up to 2,5 mm
[0.098 in]
3 mm [0.118 in]
>2 mm[0.079 in]
>2 mm [0.079 in]
dependent on target geometry
40 mm [1.57 in] 24 mm [0.94 in]
9,53 mm
17,98 mm
[0.375 in]
[0.71 in]
leaded3
Bosch 928000453
Notes:
1. Short circuit protected.
Sensing and Control
27,5 mm [1.08]
18,6 mm
[0.73 in]
Delphi-Packard
Metripak 150.2
Type 101
46 mm [1.81 in]
67 mm [2.64 in]
17,98 mm
[0.71 in]
Bosch 928000453
20,3 mm [0.80]
15,37 mm
[0.605 in]
Deutsch
DT06-3S
SNDH-H Series
Figure 1. Mounting Dimensions and General Mounting Geometry (For reference only: mm [in].)
SNDH-H3L-G01
SNDH-H3C-G03
SNDH-H3C-G04
2 Honeywell
Sensing and Control
SNDH-H Series
Figure 1. Mounting Dimensions and General Mounting Geometry (For reference only: mm [in].) (continued)
SNDH-H3C-G05
SNDH-H3C-G06
3 Honeywell
Sensing and Control
SNDH-H Series
Figure 1. Mounting Dimensions (For reference only. mm/[in] (continued)
SNDH-H3P-G01
WARNING
WARNING
PERSONAL INJURY
MISUSE OF DOCUMENTATION
DO NOT USE these products as safety or emergency stop
devices or in any other application where failure of the
product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
The information presented in this application note is for
reference only. Do not use this document as a product
installation guide.
Complete installation, operation, and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
WARRANTY/REMEDY
Honeywell warrants goods of its manufacture as being free of
defective materials and faulty workmanship. Honeywell s
standard product warranty applies unless agreed to otherwise
by Honeywell in writing; please refer to your order
acknowledgement or consult your local sales office for specific
warranty details. If warranted goods are returned to Honeywell
during the period of coverage, Honeywell will repair or replace,
at its option, without charge those items it finds defective. The
foregoing is buyer s sole remedy and is in lieu of all other
warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special,
or indirect damages.
While we provide application assistance personally, through
our literature and the Honeywell web site, it is up to the
customer to determine the suitability of the product in the
application.
Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this printing.
However, we assume no responsibility for its use.
SALES AND SERVICE
Honeywell serves its customers through a worldwide network
of sales offices, representatives and distributors. For
application assistance, current specifications, pricing or name
of the nearest Authorized Distributor, contact your local sales
office or:
E-mail: info.sc@honeywell.com
Internet: www.honeywell.com/sensing
Phone and Fax:
Asia Pacific
+65 6355-2828
+65 6445-3033 Fax
Europe
+44 (0) 1698 481481
+44 (0) 1698 481676 Fax
Latin America
+1-305-805-8188
+1-305-883-8257 Fax
USA/Canada
+1-800-537-6945
+1-815-235-6847
+1-815-2
Sensing and Control
Honeywell
1985 Douglas Drive North
Golden Valley, MN 55422
www.honeywell.com/sensing
50071164-1-EN
February 2012
Copyright © 2012 Honeywell International Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising