Honeywell | SS361CT/SS461C High Sensitivity Bipolar Latching, Hall-Effect Digital Sensor ICs | Installation Instruction | Honeywell SS361CT/SS461C High Sensitivity Bipolar Latching, Hall-Effect Digital Sensor ICs Installation Instruction

Honeywell SS361CT/SS461C High Sensitivity Bipolar Latching, Hall-Effect Digital Sensor ICs Installation Instruction
Installation Instructions for the
SS361CT/SS461C High Sensitivity Bipolar
Latching, Hall-Effect Digital Sensor ICs
ISSUE 1
50050501
Table 1. Absolute Maximum Ratings
GENERAL INFORMATION
CAUTION
ELECTROSTATIC DISCHARGE DAMAGE
This component is sensitive to electrostatic discharge (ESD). Take
normal ESD precautions in handling this product to prevent ESDinduced damage and/or degradation.
Failure to comply with these instructions may result in product
damage.
Characteristic
Supply voltage
Applied output
voltage
Output current
Magnetic flux
1
Min.
-26.0
-0.5
Typ.
–
–
Max.
28.0
28.0
Unit
Vdc
Vdc
–
–
–
–
20.0
no limit
mA
Gauss
Note 1: Absolute maximum ratings are the extreme limits that the device will
withstand without damage to the device. However, the electrical and mechanical
characteristics are not guaranteed as the maximum limits (above recommended
operating conditions) are approached, nor will the device necessarily operate at
absolute maximum ratings.
NOTICE
SOLDERING/ASSEMBLY
CAUTION
IMPROPER SOLDERING
Ensure leads are adequately supported during any
forming/shearing operation so that they are not stressed inside
the plastic case.
Limit exposure to high temperatures.
Do not wave solder the SS361CT.
Failure to comply with these instructions may result in product
damage.
SS361CT: Use an infrared reflow process with temperatures of 245 °C
[473 °F] peak for 10 s max.
SS461C: PC board wave soldering temperature is 250 °C to 260 °C
[482°F to 500 °F] peak for 3 s max.
Figure 1. Typical Magnetic Characteristics
The magnetic field strength (Gauss) required to cause the switch to
change state (operate and release) will be as specified in the
magnetic characteristics. To test the switch against the specified
magnetic characteristics, the switch must be placed in a uniform
magnetic field.
NOTICE
Bipolar Hall-Effect sensor ICs may have an initial output in either
the ON or OFF state if powered up with an applied magnetic field in
the differential zone (applied magnetic field >Brp and <Bop).
Honeywell recommends allowing 10 µs for output voltage to
stabilize after supply voltage has reached 5 V.
Figure 2. Current Sinking Output Block Diagram
Table 2. SS361CT/SS461C Performance Specifications (At 4 Vdc to 24 Vdc supply, 20 mA load, TA = -40 ºC to 125 ºC [-40 ºF to 257 ºF]
unless otherwise specified.
Characteristic
Condition
Min.
Typ.
Max.
Unit
-40 °C to 125 °C [-40 °F to 257 °F]
–
Supply voltage
4
24
Vdc
Vsupply = 5 V at 25 °C [77 °F]
–
Supply current
4
6
mA
–
–
Vsat
Gauss >95
0.4
V
–
–
µA
Output leakage current
Gauss >95
10
Vsupply = 12 V at 25 °C [77 °F]
–
–
µs
Rise/fall time
1.5
-40 °C to 85 °C [-40 °F to 185 °F]
Operate
5
50
80
Gauss
-40 °C to 125 °C [-40 °F to 257 °F]
5
50
95
-40 °C to 85 °C [-40 °F to 185 °F]
Release
-80
-50
-5
Gauss
-40 °C to 125 °C [-40 °F to 257 °F]
-95
-50
-5
-40 °C to 85 °C [-40 °F to 185 °F]
Differential
50
100
160
Gauss
-40 °C to 125 °C [-40 °F to 257 °F]
50
100
190
–
Operating temperature
Vsupply = 4 Vdc to 24 Vdc
-40 [-40]
125 [257]
°C [°F]
–
–
Storage temperature
-40 [-40]
150 [302]
°C [°F]
Sensing and Control
SS361CT/SS461C
50050501
Issue 1
Figure 2. Mounting Dimensions (For reference only. mm/[in])
SS361CT
SS461C
2,90
[0.114]
3
GND
(-)
2, 80
[0. 110]
2,5
[0.100]
NOMINAL
IC CENTER
1, 60
[0. 063]
0,46
[0.018]
4,1
[0.161]
NOMINAL
IC CENTER
1
VCC
(+)
2
OUTPUT
3.0
[0.118]
3X 0,50
[0.20]
0,95
[0.037]
NOMINAL
TO IC
SENSING
SURFACE
14,61
[0.575]
0,413
[0.016]
VS
1,20
1,45 [0.047]
[0.057]
0,787
[0.031]
2X 1,3
[0.050]
OUT
WARNING
PERSONAL INJURY
DO NOT USE these products as safety or emergency stop
devices or in any other application where failure of the
product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARRANTY/REMEDY
Honeywell warrants goods of its manufacture as being free of
defective materials and faulty workmanship. Honeywell’s
standard product warranty applies unless agreed to otherwise
by Honeywell in writing; please refer to your order
acknowledgement or consult your local sales office for specific
warranty details. If warranted goods are returned to Honeywell
during the period of coverage, Honeywell will repair or replace,
at its option, without charge those items it finds defective. The
foregoing is buyer’s sole remedy and is in lieu of all other
warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special,
or indirect damages.
While we provide application assistance personally, through
our literature and the Honeywell web site, it is up to the
customer to determine the suitability of the product in the
application.
3X 0,43
[0.017]
0,76
[0.03]
3X 0,3
[0.015]
3X 0,38
[0.015]
Figure 3. SS361CT Tape and Reel Dimensions (For reference only. mm/[in])
Tape
Reel
Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this printing.
However, we assume no responsibility for its use.
SALES AND SERVICE
Honeywell serves its customers through a worldwide network
of sales offices, representatives and distributors. For
application assistance, current specifications, pricing or name
of the nearest Authorized Distributor, contact your local sales
office or:
E-mail: info.sc@honeywell.com
Internet: www.honeywell.com/sensing
Phone and Fax:
Asia Pacific
+65 6355-2828
+65 6445-3033 Fax
Europe
+44 (0) 1698 481481
+44 (0) 1698 481676 Fax
Latin America
+1-305-805-8188
+1-305-883-8257 Fax
USA/Canada
+1-800-537-6945
+1-815-235-6847
+1-815-235-6545 Fax
Sensing and Control
Honeywell
1985 Douglas Drive North
www.honeywell.com/sensing
GND
0,77
[0.030]
0,60
[0.024]
Golden Valley, MN 55422
NS
1,83
[0.072]
1,90
[0.075]
S
N
NOMINAL
TO IC
SENSING
SURFACE
1,6
[0.062]
50050501-1-EN IL50 GLO Printed in USA
March 2010
Copyright © 2010 Honeywell International Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising