Honeywell | SS40F Enhanced Low Cost Bipolar Hall-Effect Position Sensor | Installation Instruction | Honeywell SS40F Enhanced Low Cost Bipolar Hall-Effect Position Sensor Installation Instruction

Honeywell SS40F Enhanced Low Cost Bipolar Hall-Effect Position Sensor Installation Instruction
Installation Instructions for the
SS40F Enhanced Low Cost Bipolar
Hall-Effect Position Sensor
ISSUE 2
50028565
CLEANING
WARNING
PERSONAL INJURY
DO NOT USE these products as safety or emergency stop
devices or in any other application where failure of the
product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
CAUTION
IMPROPER CLEANING
Do not use pressure wash. High-pressure stream could
force contaminants into the package.
Failure to comply with these instructions may result in
product damage.
Use agitated rinse to clean the sensor.
NOTICE
Bipolar Hall-effect sensors may have an initial output in
either the ON or OFF state if powered up with an applied
magnetic field in the differential zone (applied magnetic field
>Brp and <Bop). Honeywell recommends allowing 10 s for
output voltage to stabilize after supply voltage has reached
5 V.
SOLDERING/ASSEMBLY
Support leads during all forming or shearing operations to
ensure they are not stressed inside the plastic case. Wave
solder at 250 C to 260 C (482 F to 500 F) for a maximum of
5 s.
TABLE 1. SPECIFICATIONS (At Vs = 4.5 V to 24 V with 20 mA load with Ta = 25 C [77 F] unless otherwise noted.
Characteristic
Condition
Minimum
Typical
Maximum
Unit
Supply voltage
4.5
24.0
V
Supply current
6.8
10.0
mA
Output current
20.0
mA
Vsat at 15 mA
gauss >170
0.4
V
Output leakage
gauss <-170
1.0
A
Rise time
Vs = 4.5 V
0.5
1.5
s
Fall time
Vs = 4.5 V
0.2
1.5
s
Operate (Bop)
4.5 (45)
11 (110)
mT (gauss)
-4.5 (-45)
Release (Brp)
-11 (-110)
mT (gauss)
Differential
5.0 (50)
mT (gauss)
Operating temperature
-40 C to 125 C [-40 F to 257 F]
Storage temperature
-65 C to 160 C [-85 F to 329 F]
TABLE 2. ABSOLUTE MAXIMUM RATINGS*
Characteristic
Supply voltage
Applied output voltage
Output current
Magnetic flux
*Note:
Minimum
-28
-0.5
Typical
Maximum
28
28
20
no limit
Unit
V
V
mA
gauss
Absolute maximum ratings are the extreme limits the device is designed to withstand without damage to the device. However, the electrical and
mechanical characteristics are not guaranteed as the maximum limits (above recommended operating conditions) are approached, nor will the
device necessarily operate at absolute maximum ratings.
Sensing and Control
SS40F
Hall
Sensor
Issue 2
Trigger
Circuit
And
Amplifier
Vs (+)
Output (O)
Ground (-)
50028565
SS40F
Issue 2
50028565
SS40F
Issue 2
WARRANTY/REMEDY
Honeywell warrants goods of its manufacture as being free of
defective materials and faulty workmanship. Honeywell’s
standard product warranty applies unless agreed to otherwise
by Honeywell in writing; please refer to your order
acknowledgement or consult your local sales office for specific
warranty details. If warranted goods are returned to Honeywell
during the period of coverage, Honeywell will repair or replace,
at its option, without charge those items it finds defective. The
foregoing is buyer’s sole remedy and is in lieu of all other
warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special,
or indirect damages.
While we provide application assistance personally, through
our literature and the Honeywell web site, it is up to the
customer to determine the suitability of the product in the
application.
Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this printing.
However, we assume no responsibility for its use.
50028565
SALES AND SERVICE
Honeywell serves its customers through a worldwide network
of sales offices, representatives and distributors. For
application assistance, current specifications, pricing or name
of the nearest Authorized Distributor, contact your local sales
office or:
E-mail: info.sc@honeywell.com
Internet: www.honeywell.com/sensing
Phone and Fax:
Asia Pacific
+65 6355-2828
+65 6445-3033 Fax
Europe
+44 (0) 1698 481481
+44 (0) 1698 481676 Fax
Latin America
+1-305-805-8188
+1-305-883-8257 Fax
USA/Canada
+1-800-537-6945
+1-815-235-6847
+1-815-235-6545 Fax
50028565-2-EN IL50 GLO Printed in USA
June 2009
Copyright © 2009 Honeywell International Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising