Honeywell | SS41G Low Cost, Digital Bipolar Hall-Effect Sensor ICs | Installation Instruction | Honeywell SS41G Low Cost, Digital Bipolar Hall-Effect Sensor ICs Installation Instruction

Honeywell SS41G Low Cost, Digital Bipolar Hall-Effect Sensor ICs Installation Instruction
Installation Instructions for the
Low-cost, Bipolar Digital Hall-effect
Sensor ICs: SS41G
50028377
Issue C
CLEANING
GENERAL INFORMATION
CAUTION
CAUTION
CAUTION
ELECTROSTATIC
DISCHARGE DAMAGE
Ensure proper ESD
precautions are followed when
handling this product.
Failure to comply with these
instructions may result in
product damage.
ELECTROSTATIC
SENSITIVE
DEVICES
DO NOT OPEN OR HANDLE
EXCEPT AT A
STATIC FREE WORKSTATION
ESD SENSITIVITY:
CLASS 2
IMPROPER CLEANING
Do not use pressure wash. High-pressure stream could force
contaminants into the package.
Failure to comply with these instructions may result in
product damage.
Use agitated rinse to clean the sensor.
Table 2. Absolute Maximum Specifications
Characteristic
SOLDERING/ASSEMBLY
CAUTION
IMPROPER SOLDERING
• Ensure leads are adequately supported during any forming/
shearing operation so that they are not stressed inside the
plastic case.
• Limit exposure to high temperatures.
Failure to comply with these instructions may result in
product damage.
See Table 1 for soldering information.
Min.
Typ.
Max.
Unit
Supply voltage
-50.0
—
50.0
V
Applied output voltage
-0.5
—
50.0
V
Output current
—
—
20
mA
Magnetic flux
—
—
no limit
Gauss
NOTICE
Absolute maximum ratings are the extreme limits the device will
momentarily withstand without damage to the device. Electrical and mechanical characteristics are not guaranteed if the
rated voltage and/or currents are exceeded, nor will the device
necessarily operate at absolute maximum ratings.
Table 2. Electrical and Environmental Specifications
(At Vsupply = 4.5 Vdc to 24.0 Vdc, 20 mA load, TA = -40 ºC to 150 ºC [-40 ºF to 302 ºF] except where otherwise specified.
Characteristic
CCondition
Min.
Typ.
Max.
Unit
Supply voltage
Supply current:
ouptut off
output on
Output current
—
4.5
—
24.0
Vdc
—
—
—
—
—
—
6.8
—
—
10.0
11.3
20.0
mA
Vsat at 20 mA
mA
Vsupply = 12.0 Vdc, Brp >170, 25 ºC [77 ºF]
—
—
0.4
V
Vsupply = 24.0 Vdc, Brp <-170
—
—
10.0
μA
Rise time
25 ºC [77 ºF]
—
0.5
1.5
μs
Fall time
Magnetic characteristics:
operate (Bop)
operate (Bop)
release (Brp)
release (Brp)
differential
Operating temperature
25 ºC [77 ºF]
—
0.2
1.5
μs
25 ºC [77 ºF]
—
25 ºC [77 ºF]
—
—
—
—
—
-140
-250
40
-40 [-40]
40
—
-40
—
—
—
150
250
—
—
—
150 [302]
°C [°F]
—
-40 [-40]
—
150 [302]
°C [°F]
per JEDEC JS-001
--3
—
+3
kV
Output leakage current
Storage temperature
ESD (Human Body Model)
Soldering temperature and time
NOTICE
PC board wave soldering process: 250 °C to 260 °C [482 °F to 500 °F] for 3 s max.
These Hall-effect sensor ICs may have an initial output in either
the ON or OFF state if powered up with an applied magnetic field
in the differential zone (applied magnetic field >Brp and <Bop).
Honeywell recommends allowing 10 μs after supply voltage has
reached 3 V for the output voltage to stabilize.
Sensing and Productivity Solutions
Gauss
NOTICE
The magnetic field strength (Gauss) required to cause the
switch to change state (operate and release) will be as
specified in the magnetic characteristics. To test the switch
against the specified limits, the switch must be placed in a
uniform magnetic field.
Low-cost, Bipolar Digital Hall-effect Sensor ICs:
SS41G
Figure 1. Magnetic Performance vs Temperature (Vsupply = 12 Vdc)
Issue C
50028377
Figure 2. Current Sinking Ouptut Block Diagram
250
Magnetic Swith Point (Gauss)
200
150
Operate max.
100
Operate typ.
50
Vsupply (+)
0
-50
Hall
Sensor IC
Release typ.
-100
Trigger
Circuit
and Amplifier
Output (O)
Ground (-)
Release min.
-150
-200
-250
-40
[-40]
-20
[-4]
0
[32]
20
[68]
40
[104]
60
[140]
80
[176]
100
[212]
120
[248]
140
[284]
160
[320]
Ambient Temperature (°C [°F])
Figure 3. Wiring Diagrams
+DC
5 Vdc
5 Vdc
R
10 kΩ
Sensor
IC
+ 5 Vdc
2N3638
PNP
Transistor
R
47 kΩ
+
R1
Sensor 550 Ω
IC
5 Vdc
TTL or
DTL Gate
R
100 Ω
LED
R
47 kΩ
+
R1
Sensor 680 Ω
IC
+13 Vdc
2N3638
PNP
Transistor
100 mA
Relay
Coil
-
2
Load
Sensor
IC
50 mA
-
-
13 Vdc
+10 Vdc
5 Vdc
R
+ 1.2 kΩ
Sensing and Productivity Solutions
10 Vdc
+
Sensor
IC
R1
47 kΩ
R
750 Ω
PNP
Transistor
R
2N2222
NPN
Transistor
-
HI
+15 Vdc
150 mA
5 Vdc
+
Load
SCR
R
LOW
Sensor
IC
R
4.7 kΩ
R1
1.8 kΩ
AC
HI
+15 Vdc
PNP
Transistor
R
Load
TRIAC
R
LOW
Low-cost, Bipolar Digital Hall-effect Sensor ICs:
SS41G
Issue C
50028377
Figure 4. Sensor IC Mounting Dimensions (For reference only. mm/in.)
4,00
[0.157]
1,52
[0.060]
2,50
[0.098]
0,75
[0.030]
41G
1,74
[0.069]
0,45
[0.018]
NS
3,00
[0.118]
14,5
[0.571]
Ground
Vs
3X 0,38
[0.015]
Output
3X 0,56 Max.
[0.022]
2X 1,27
[0.05]
3X 0,38
[0.015]
Sensing and Productivity Solutions
3
WARNING
PERSONAL INJURY
DO NOT USE these products as safety or emergency stop
devices or in any other application where failure of the product
could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARRANTY/REMEDY
Honeywell warrants goods of its manufacture as being free
of defective materials and faulty workmanship. Honeywell’s
standard product warranty applies unless agreed to otherwise
by Honeywell in writing; please refer to your order acknowledgement or consult your local sales office for specific warranty
details. If warranted goods are returned to Honeywell during the
period of coverage, Honeywell will repair or replace, at its option, without charge those items it finds defective. The foregoing is buyer’s sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. In no event shall
Honeywell be liable for consequential, special, or indirect
damages.
While we provide application assistance personally, through our
literature and the Honeywell web site, it is up to the customer to
determine the suitability of the product in the application.
Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this printing.
However, we assume no responsibility for its use.
Honeywell serves its customers through a worldwide network of
sales offices, representatives and distributors. For application
assistance, current specifications, pricing or name of the nearest
Authorized Distributor, contact your local sales office or:
E-mail: info.sc@honeywell.com
Internet: sensing.honeywell.com
Phone and Fax:
USA/Canada
+1-800-537-6945
International
+1-815-235-6847; +1-815-235-6545 Fax
Sensing and Productivity Solutions
Honeywell
1985 Douglas Drive North
Golden Valley, MN 55422
honeywell.com
50028377-C-EN IL50
October 2015
© 2015 Honeywell International Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising