Honeywell | SS49/SS19 Series Analog Position Sensors | Installation Instruction | Honeywell SS49/SS19 Series Analog Position Sensors Installation Instruction

Honeywell SS49/SS19 Series Analog Position Sensors Installation Instruction
Installation Instructions for the
SS49/SS19 Series Analog Position Sensors
PERSONAL INJURY
• DO NOT USE these products as safety or
emergency stop devices, or in any other
application where failure of the product could
result in personal injury.
Failure to comply with these instructions could
result in death or serious injury.
SS49/SS19 ELECTRICAL CHARACTERISTICS
Supply Voltage
4 to 10 VDC
Supply Current
4 mA typ.
Output Type
Analog Sourcing
Output Voltage @ 0
Gauss, 25°C
1.75 to 2.25 V @ 5 V
Sensitivity (measured
between -400 and +400
gauss), mV/G
Min.
0.60
Operating Temperature
-40 to +100°C (-40 to 212°F)
Typ.
0.90
Max.
1.25
ABSOLUTE MAXIMUM RATINGS*
Supply Voltage (Vs)
± 12 VDC
Output Current
20 mA
Storage Temperature
-55 to +150°C (-67 to
+302°F)
Magnetic Flux
No limit. Circuit cannot be
damaged by magnetic
overdrive.
* Absolute maximum ratings are the extreme limits that
the device will withstand without damage to the device.
However, the electrical and mechanical characteristics
are not guaranteed as the maximum limits (above
recommended operating conditions) are approached, nor
will the device necessarily operate at absolute maximum
ratings.
ISSUE 4
PK 88740
SOLDERING/ASSEMBLY
SS49
Support leads during any forming/shearing
operation. Do not stress leads inside plastic case.
Hand soldering - Use 60/40 rosin core solder,
and a 399°C (750°F) controlled temperature, 1/8”
chisel tip soldering iron. Do not hold iron on
terminals for more than four seconds. Lead
temperature at package must not exceed 250°C
(482°F).
Wave soldering - Use Loncoflux 106A35 or
equivalent. Set preheaters at 95°C (200°F) for top
(component side) of PC board just prior to entering
wave. (This may be adjusted depending upon
board thickness.) Set solder temperature at 252°C
to 260°C max. (485°F to 500°F). Set conveyor
speed to about 4.5 feet per minute (1,37
meter/min.), choosing a speed which gives full
solder fillets and minimum bridging and icicles.
Provide rigid support for the board.
SS19/SS19T
Honeywell recommends an infrared reflow
process with peak temperatures not to exceed 190 200°C (374 - 392°F) for 10 seconds maximum.
Keep exposure to high temperatures minimal.
CLEANING
Clean appropriately in accordance with applicable
safety procedures. Honeywell recommends manual
cleaning.
BLOCK DIAGRAM
TRANSFER CHARACTERISTICS
Sensing and Control
SS49/SS19 Series
Issue 4 PK 88740
TYPICAL OUTPUT CHARACTERISTICS
2 Honeywell • Sensing and Control
For application help: call 1-800-537-6945
SS49/SS19 Series
ISSUE 4
PK 88740
MOUNTING DIMENSIONS (for reference only)
SS49 SERIES
SS19 SERIES
For application help: call 1-800-537-6945
Honeywell • Sensing and Control 3
SS49/SS19 Series
WARRANTY/REMEDY
Honeywell warrants goods of its manufacture as
being free of defective materials and faulty
workmanship. Contact your local sales office for
warranty information. If warranted goods are
returned to Honeywell during the period of
coverage, Honeywell will repair or replace without
charge those items it finds defective. The
foregoing is Buyer’s sole remedy and is in lieu
of all other warranties, expressed or implied,
including those of merchantability and fitness
for a particular purpose.
Specifications may change without notice. The
information we supply is believed to be accurate
and reliable as of this printing. However, we assume
no responsibility for its use.
While we provide application assistance
personally, through our literature and the Honeywell
web site, it is up to the customer to determine the
suitability of the product in the application.
For application assistance, current specifications
or name of the nearest Authorized Distributor,
contact a nearby sales office. Or call:
1-800-537-6945 USA/Canada
1-815-235-6847 International
FAX
1-815-235-6545 USA
INTERNET
www.honeywell.com/sensing
info.sc@honeywell.com
Sensing and Control
www.honeywell.com/sensing
Honeywell
11 West Spring Street
Freeport, Illinois 61032
88740-4-EN IL50 GLO 104 Printed in USA
Copyright 2004 Honeywell International Inc. All Rights Reserved.
Issue 4 PK 88740
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising