Gardena Electronic Pressure Pump Operators Manual

Gardena Electronic Pressure Pump Operators Manual
D
GB
Art. 1763
4000/5 LCD
Art. 1765
5000/5 LCD
Art. 1767
S
NL
6000/5 Inox LCD Art. 1769
F
4000/4 LCD
E
P
DK
Betriebsanleitung
Hauswasserautomat
GB Operating Instructions
Electronic Pressure Pump
F
Mode d’emploi
Station de pompage
NL Instructies voor gebruik
Hydrofoorpomp
S Bruksanvisning
Pumpautomat
I
Istruzioni per l’uso
Pompa ad intervento automatico
E Manual de uso
Estación de Bombeo
P Instruções de utilização
Bomba de Pressão
DK Brugsanvisning
Husvandværk
I
D
GARDENA Electronic Pressure Pump 4000/4
LCD, 4000/5 LCD, 5000/5 LCD, 6000/5 Inox LCD
Welcome to the Garden of GARDENA ...
GB
Translation of the original instructions from German. Please read
these operating instructions carefully and observe the notes given.
Use these operating instructions to familiarise yourself with the
Pressure Tank Unit, its correct use and the notes on safety.
For safety reasons, children under the age of 16 and people not
familiar with these operating instructions must not use this Pressure
Tank Unit.
➔ Please keep these operating instructions in a safe place.
Contents:
1. Suitable uses for Your GARDENA Elelctronic
Pressure Pump . . . . . . . . . . . . . . . . . . . . . .
2. Safety Instructions . . . . . . . . . . . . . . . . . . . .
3. Function and Display . . . . . . . . . . . . . . . . . .
4. Using the Equipment for the First Time . . . . .
5. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .
6. Preparation for Storage . . . . . . . . . . . . . . . . .
7. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . .
8. Troubleshooting / Service . . . . . . . . . . . . . . . .
9. Accessories Available . . . . . . . . . . . . . . . . . .
10. Technical Data . . . . . . . . . . . . . . . . . . . . . . .
11. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
14
15
15
17
18
20
20
21
24
24
25
1. Suitable uses for Your GARDENA Electronic Pressure Pump
Correct use:
GARDENA Electronic Pressure Pumps have been designed for
private use around the house and garden. Pressure Tank Units are
predominantly used for operating watering implements and
systems in private gardens.
When using the pump for pressure intensification, the maximum
permissible internal pressure of 6 bar (on the delivery side) must
not be exceeded. The in creased delivery pressure and the pump
pressure have to be added together.
• Example: pressure at the tap = 1.5 bar, maximum pressure of
the Pressure Tank Unit 4000/4 LCD = 4.4 bar, total pressure =
5.9 bar.
Liquids that can be pumped:
Please note:
14
The GARDENA Electronic Pressure Pump can be used for pumping
rainwater, tap water and chlorinated swimming pool water.
The GARDENA Electronic Pressure Pump is not suitable for
continuous operation (e.g. industrial applications, continuous
circulating operation). Corrosive, easily combustible,
aggressive or explosive liquids (such as gasoline, petroleum
or nitrothinner), saltwater and food must not be pumped. The
temperature of the liquid must not exceed 35 °C.
Empty your Electronic Pressure Pump before the first frost of
the season (see 6. Preparation for Storage).
2. Safety Instructions
Risk of injury due to electric shock.
➔ Always unplug your Electronic Pressure
Pump before filling, after operation,
when trouble-shooting and before
carrying out any maintenance work.
Location
Caution: Pursuant to DIN VDE 0100-702 and
0100-738 use of the pump near to swimming
pools and garden ponds and other similar
places is only permissible if the pump is
operated via a residual-current device (FI switch)
with a residual current rating of 울 30 mA. The
pump must not be operated when there are
persons in the swimming pool or garden pond.
The pump must be located on solid, even
ground, protected from flooding. Take care that
the pump cannot fall into water. As an additional safety device an authorised safety switch
can be used.
➔ Please ask your electrician for advice.
Extension cables
Data indicated on the type plate must match
technical data of the mains supply.
Pursuant to DIN VDE 0620, power cable as
well as extension cables must not have a
smaller diameter than rubber sheathed cables
described with letter symbols H07 RNF.
Protect the power cable from heat, oil and
sharp edges.
➔ Do not use the power cable for carrying the
pump or for unplugging.
In Austria
In Austria, the electrical connections must be
made according to ÖVE-EM 42, T2 (2000)/
1979 § 22 based on § 2022. Pursuant to this
regulation it is imperative to operate pumps for
swimming pools and garden ponds exclusively
via an isolating transformer.
➔ Please ask your electrician for advice.
In Switzerland
In Switzerland mobile appliances which are
used outdoors must be connected via a
residual-current device.
GB
Warning ! Electric shock !
Visual check
➔ Before operating the pump, first make a
visual check, if there is any damage to the
pump (especially regarding power cable
and plug).
A damaged pump must not be used.
➔ In case of damage, please have the pump
checked by our GARDENA Service Centre
or by an authorised electrician.
Safety in operation
➔ Protect the pump from rain. Do not use the
pump in a wet or moist area.
In order to avoid dry-running of the pump, take
care that the end of the suction hose is always
submerged into the water.
➔ Before each operation, fill the pump to
overflowing with approx. 2 to 3 l of water to
be pumped !
When in manual mode for troubleshooting, the
pump may not be operated for longer than
10 min. with the output side closed (1 cycle).
The pump must not perform more than 4
suction cycles (duration 4 minutes respectively)
one after the other.
➔ Allow pump to cool down before further use.
Sand and other abrasive substances in the
water cause increased wear and reduce the
pump’s output.
➔ Use a preliminary filter on the pump if the
water is sandy.
The minimum flow rate is 140 l/h (= 2.3 l/min).
Watering accessories with lower rate must not
be operated.
When using the pump for domestic water
supply, please adhere to the local water and
sewerage regulations. In addition observe the
regulations of DIN 1988.
➔ If necessary, contact your local water authority.
3. Function and Display
The Electronic Pressure Pump is electronically controlled. The
electronic control is activated by pulses from the manometric switch
and from the throughput detector of the dry-running preventer.
The manometric switch is set to a switch-on pressure of approx
2.0 bar (= 20 m head) at the factory. The dry-running preventer
protects the pump from damage by turning the pump off if necessary.
15
Electronic control display
GB
Power ON display:
The pump is connected to the mains.
Pump ON display:
The pump is pumping.
Manual display:
Only displayed in manual operation.
l/h or bar display:
Indicates whether throughput or pressure is being displayed.
Frost symbol:
The temperature in the pump was or is below 3 °C.
M I N M A X display:
MIN: The throughput is below 300 l/h (5 l/min)
MAX: The throughput is at maximum.
Reset key:
Used for resetting the throughput indicator
the frost symbol and restarting after a fault.
, cancelling
Shift key:
Used for moving the display forwards.
Manual key:
Used for pumping manually if the shift key is pressed at the
same time.
Operating modes
Priming cycle
Pump ON
flashes.
Throughput during operation
(pump is delivering water)
Pump tries to draw in water
for a maximum of 4 minutes.
Throughput > 300 l/h to MAX
(display in 100 l/h increments).
Maximum throughput.
Throughput > 140 l/h and
less than 300 l/h.
Pump ON
flashes.
Standby
16
Throughput < 140 l/h.
No water is being drawn off
and the pump has switched
off at maximum pressure.
Position of equipment:
The point at which the unit is fixed must be sound, dry and well
ventilated and must permit the pump to be set up in a stable
position.
➔ Install the pump at a safe distance (min. 2 m) from the pumping medium.
The pump must be installed in a location with low air humidity
and sufficient ventilation in the area of the ventilation slots. It
must be at a distance of at least 5 cm from the walls. No dirt
contamination (e.g. sand or earth) may be sucked in through the
ventilation slots.
Install automatic domestic
water system permanently:
The mounting plate prevents the pump moving.
1. Screw mounting plate
on to an appropriate base.
2. Place pump on the base with both feet .
Set the pump such that a suitably large container can be positioned
below the drain screw for emptying the pump or unit .
If possible, install the pump higher than the surface of the water to
be pumped. If this is not possible, install a vacuum-resistant shutoff device between the pump and the suction hose, for example
for cleaning the integrated filter.
If you install your Electronic Pressure Pump permanently indoors to
supply water for domestic use, connect your pump to the pipe
network using flexible hoses rather than rigid pipes. This will help
reduce noise and prevent damage to the manometric switch
due to vibration.
If the system is being installed permanently, please fit suitable
shut-off devices on both the intake and delivery sides. This is
important e.g. for maintenance and cleaning work or if the system
is being shut down.
The connection pieces on the intake and delivery sides must
only be tightened by hand.
Connect the hose to the
suction side:
Do not use any water hose snap connection system components
on the intake side. A vacuum-tight suction hose must be used e.g.
• GARDENA Suction Hose art. 1411
• GARDENA borehole Suction Hose art. 1729.
To reduce the pump repriming time, we recommend:
Art. 1723 /
Art. 1724
• using a suction hose with backflow preventer, which prevents
the suction hose emptying automatically when the Pressure
Tank Unit is switched off
• If the suction heights are high, use a suction hose with a small
diameter.
1. Connect vacuum-tight suction hose via a connection piece
(e.g. art. 1723 / 1724) to the connection on the intake side
and screw in place so that it is airtight.
2. For suction heights exceeding 4 m also secure the suction
hose (e.g. by fastening it to a wooden post).
This relieves the pump of the weight of the suction hose.
If very fine dirt is present, we recommend the use of a
GARDENA pump preliminary filter art. 1730 / 1731 in addition
to the integrated filter.
17
GB
4. Using the Equipment for the First Time
Connect hose to output side:
6b
GB
The hose can be connected either to the delivery side 33.3 mm
(G 1)-thread of the 120° swivelling connection 6b and/or of the
horizontal connection .
1. Seal the connection not required with the sealing cap provided.
2. Connect delivery hose to the delivery side connection.
TIP:
Use pressure-tight hoses, such as e.g. the GARDENA Profi Plus
hose with 19 mm (3/4“) diameter, art. no. 4432 / 8452, in conjunction
with the GARDENA fast connection threaded connector with a
33.3 mm (G1) internal thread art. no. 7109 and the GARDENA
suction and high pressure connector, art. no. 7120, for 19 mm
(3/4“) hoses and a GARDENA hose clamp art. no. 7192.
Never use suction hoses.
5. Operation
Electronic Pressure Pump
turn on:
Danger ! Electric shock !
Risk of injury due to electric shock.
➔ Unplug the pump from the mains before filling.
Warning ! Pump running dry.
➔ Fill the pump to the overflow (approx. 2 to
3 litres) with the water each time before the
pump is switched on.
1. Unscrew the cover of the filter chamber by hand.
2. Turn rotary switch to START.
The integrated non-return valve will open.
3. Open any shut-off devices in the delivery line (watering
accessories, water stop, etc.) so that air can escape before the
priming procedure begins.
4. Empty any water remaining in the delivery hose so that the air
can escape during filling and priming.
5. Fill slowly with water via the filler connection until it
overflows (approx. 2 to 3 l).
6. Close cover of the filter chamber by hand again.
The maximum self-priming head of 9 m (art. 1769 8 m) is only
achieved if the pump is filled until it overflows via the filler connection
and the delivery hose is held high enough so that no water can
escape via the delivery hose. It is not necessary to hold up the
delivery hose if filled suction hoses with backflow preventer are
used.
7. Insert mains plug into a 240 V / 50 Hz AC socket.
Warning! The pump will start immediately!
Priming cycle
18
During the priming cycle (01) the pump will try to draw in
water for 4 minutes.
In some circumstances ERROR 06 may appear. This does not
impair the further operation of the pump.
8. When the pump has drawn in the water, turn the rotary switch
to RUN.
The pump switches off automatically when the maximum
pressure is reached. Normal mode (standby) has been reached
(
).
Normal mode
(standby)
Change display information:
In operation:
Throughput display in
l/h
(in 100 l/h increments)
Press shift key.
In operation:
Pressure display
in bar.
Standby:
Pump has reached
max. pressure.
(in 0,2 bar increments)
Press shift key.
Normal mode
(display for 3 seconds)
Normal mode
(display for 3 seconds)
Press shift key.
Quantity delivered in
m3 since first start-up
(display for 3 seconds)
Press shift key.
Quantity delivered in
m3 since last reset.
(display for 3 seconds)
Press shift key to return to throughput display, pressure display or standby.
and
RESET key:
automatically return to throughput display or standby after one minute..
Reset quantity delivered display
:
If the RESET key is pressed whilst
is operating (quantity
conveyed in m3 since last reset) only the
display is reset to 0.
This permits the quantity delivered to be measured at any desired
time interval.
➔ Hold RESET key down for 2 seconds.
Restart after a fault:
If a fault has occurred, the pump can be switched on again
prematurely by pressing the RESET key.
➔ Press RESET key.
The frost symbol goes out after the RESET key is pressed.
19
GB
9. Close shut-off devices in the delivery pipeline again.
6. Preparation for Storage
Winter storage / out of use:
Empty the Electronic Pressure Pump before the first frost.
1. Unplug the pump from the mains.
2. Turn rotary switch to .START.
GB
3. Unscrew drain bolt .
The pump will be drained.
4. Store the pump in a frost-free, dry place.
Disposal:
Unit may not be disposed of with normal household waste but
must be disposed of in accordance with environmental
regulations.
(in accordance with
directive 20002/96/EC)
7. Maintenance
Danger ! Electric shock !
There is a risk of injury from electric power.
➔ Pull out mains plug before undertaking any maintenance.
Clean built-in filter:
Clean non-return valve:
20
1. Turn rotary switch to RUN.
2. If necessary, close all the shut-off devices on the intake side.
3. Unscrew and remove cover of the filter chamber.
4. Draw out filter unit vertically
upwards.
5. Hold beaker firmly, turn filter
anti-clockwise 1 and draw
out 2 (bayonet fitting).
6. Clean beaker under running
water and clean the filter e.g.
with a soft brush.
7. Refit filter again in reverse order.
1. Pull out mains plug.
2. Turn rotary switch to START.
3. If necessary, close all the shut-off
devices on the intake side.
4. Open all the valves so that the delivery
side is not under pressure.
5. Unscrew the drain screw bolt and
drain out water.
6. Unscrew screw and push the
holder upwards 1 and backwards
2 into the bearing groove.
7. Unscrew cover of non-return
valve with a suitable tool.
8. Remove valve body and clean under running water.
9. Refit non-return valve again in reverse order.
10. Switch Electronic Pressur Pump on again (see 5. Operation).
GB
8. Troubleshooting / Service
Danger ! Electric shock !
Risk of injury due to electric shock.
➔
Unplug your Electronic Pressure Pump from the mains
before troubleshooting.
No display appears
Possible cause
Remedy
Power failure.
➜ Check fuses and cables.
Thermal overload switch of
pump has switched off
because of overload.
➜ Unplug from mains and
allow pump to cool down.
➜ Ensure compliance with
maximum temperature of the
delivery medium (35 °C).
➜ Ensure the pump is located
in a well-ventilated area.
Interruption to power supply.
➜ Contact GARDENA Service.
Direct sunlight
(Display temperature > 65 °C).
➜ The function continues to
operate. The display
reappears after the
temperature drops.
The pump attempted to draw in water for 4 min. after start-up.
The pump is now in the wait position for one minute before
starting a new suction attempt (display 01 ).
After 4 attempts at suction the pump has switched off
automatically.
Possible cause
Remedy
Leak on the suction side.
➜ Check all suction hose
connections.
Suction hose is no longer in
the water.
➜ Submerge end of suction
hose fully in the water.
Water reservoir (e.g.
underground storage tanks)
empty.
➜ Check the water level is high
enough.
Suction filter or backflow
preventer blocked.
➜ Clean filter or backflow
preventer.
21
GB
The pump has switched off.
Possible cause
Remedy
Rotary switch of non-return
valve is set to START.
➜ Turn rotary switch to RUN.
Non-return valve of the
manometric switch is blocked.
➜ Clean non-return valve
(see 7. Maintenance).
Seal failed on the output side
(leak).
➜ Check outlet and all hose
and accessories connected
to it for leaks.
Deposits of dirt on the impeller
of the dry-running safety
device.
➜ Contact GARDENA Service.
Throughput was < 140 l/h for
several minutes.
➜ Increase throughput.
Note: Even a small leak (loss of just a few ml) can cause the
pressure to drop below the pressure needed for switching
on the pump. The cause is often small leaks in taps or WCcisterns.
Pump ON
flashes
Shortage of water during operation. The pump tries to draw in
water twice (4 min. pumping time with 1 minute interval).
The pump is in the wait position before starting new attempts at
suction after 1 min / 1 h / 5 h / 24 h.
Pump ON
flashes
The pump tries to draw in water 3 times (4 minutes pumping time
in each case after 1 h / 5 h / 24 h interval).
After 5 suction attempts, the pump switches off.
Possible cause
Remedy
Leak on the suction side.
➜ Check all the suction
connections.
Suction hose is no longer in the ➜ Submerge end of suction
hose fully in the water.
water.
Water reservoir (e.g. underground storage tanks) empty.
➜ Check the water level is
high enough.
Suction filter or backflow
preventer blocked.
➜ Clean filter or backflow
preventer.
After rectifying the faults ERROR 02, ERROR 03, ERROR 04, ERROR 07,
ERROR 09 the pump can only be restarted by pressing the reset
key.
The pump has switched on and off frequently although no water
has been drawn off.
22
Possible cause
Remedy
Not watertight on the delivery
side (leak).
➜ Check delivery pipeline and
valves/ taps connected to it
for leaks.
Remedy
➜ Contact GARDENA Service.
➜ Increase throughput.
➜ Turn rotary switch to RUN.
GB
Possible cause
Deposits of dirt on the impeller
of the dry-running safety device.
Throughput was < 140 l/h for
several minutes.
Rotary switch of non-return
valve is set to START.
Non-return valve of the
manometric switch is blocked.
➜ Clean non-return valve
(see 7. Maintenance).
Note: Even a small leak (loss of just a few ml) can cause the
pressure to drop below the pressure needed for switching
on the pump. The cause is often small leaks in taps or WCcisterns.
If ERROR 10 (leakage) occurs, the pump can only be switched on
again by unplugging the mains plug and plugging it in again.
Pump ON
flashes
Reduction in throughput on the output side:
The pump indicates on the throughput display or pressure display
that the throughput on the output side is < 140 l/h.
(The pump also switches on and off frequently)
Possible cause
Remedy
Relatively large leak on the
delivery side.
➜ Rectify leak.
Filter blocked.
➜ Clean filter and make sure
water level is adequate.
Throughput < 140 l/h
➜ Increase throughput
Reduction in throughput on the intake side:
The pump displays MAX l/h or MIN bar, although a low throughput
is present.
Manual operation for
fault location:
Manual
flashes
Manual
flashes
Possible cause
Remedy
Leak on the suction side.
➜ Check all intake connections.
Suction hose end is partially in
the water.
➜ Submerge end of suction
hose fully in the water.
Water reservoir (e.g. underground tank) is almost empty.
➜ Ensure water level is high
enough.
Inlet filter or backflow preventer
blocked.
➜ Inlet filter or backflow
preventer blocked.
The pump can be switched on for 10 minutes for fault location
without the pump being switched off prematurely by the electronic
control system and an error being reported ( ERROR).
1. Press shift and manual keys simultaneously.
The control electronics of the pump are disabled, OFF.
2. Press shift and manual keys again simultaneously.
Pump starts in manual mode, Manual flashes and the time
remaining is shown in minutes (10).
3. Press shift and manual key again simultaneously.
Manual operation is discontinued prematurely.
Pressing the reset key returns the system to normal mode.
If any other faults occur, please contact GARDENA Service.
23
GB
9. Accessories Available
GARDENA suction kit
Vacuum-tight spiral hose, ready
• Art. no. 1411/1418
for connection with suction filter
and backflow preventer, 25 mm (1“).
GARDENA Suction Hoses
Kink- and vacuum-resistant, sold by the metre with 19 mm (3/4”)
or 25 mm (1”) diameter without fittings or in fixed length,
complete with fittings.
GARDENA Suction Hose Fittings
• Art. no. 1723/1724
GARDENA Suction Filter
To equip suction hoses with
• Art. no. 1726/1727/1728
Backflow Preventer sold by the metre.
GARDENA
Pump Preliminary Filter
Recommended for pumping
sandy water.
GARDENA
Bore Hole Suction Hose
For vacuum-resistant connection
• Art. no. 1729
of the pump to boreholes or pipe
networks. Length 0.5 m. With 33.3 mm
(G1) female thread at both ends.
• Art. no. 1730/1731
10. Technical Data
Art. 1763
Art. 1765
Art. 1767
Art. 1769
6000/5 Inox LCD
Type:
4000/4 LCD
4000/5 LCD
5000/5 LCD
Rated power:
850 W
1000 W
1300 W
1000 W
Weight:
10 kg
10 kg
12 kg
12 kg
Max. delivery capacity:
3600 l/h
3600 l/h
4500 l/h
5500 l/h
Max. delivery head:
44 m
50 m
52 m
46 m
Max. pressure:
4,4 bar
5,0 bar
5,2 bar
4,6 bar
Cut-in pressure approx.:
2,0 bar
2,0 bar
2,0 bar
2,0 bar
9m
9m
8m
Max. self-priming suction height: 9 m
Perm. internal pressure
(delivery side):
6 bar
6 bar
6 bar
6 bar
Pump drive:
Jet
Jet
Jet
4-stage
Voltage / Frequency:
230 V / 50 Hz
230 V / 50 Hz
230 V / 50 Hz 230 V / 50 Hz
Noise emission value LWA1)
Measured:
Guaranteed:
74 dB (A)
75 dB (A)
76 dB (A)
79 dB (A)
80 dB (A)
81 dB (A)
1) Measuring method complying with directive 2000/14/EC
24
74 dB (A)
77 dB (A)
11. Warranty
This guarantee covers all serious defects of the unit that can be
proved to be material or manufacturing faults. Under warranty we
will either replace the unit or repair it free of charge if the following
conditions apply:
• The unit must have been handled properly and in keeping with
the requirements of the operating instructions.
• Neither the purchaser or a non-authorised third party have
attempted to repair the unit.
The impeller and filter are wearing parts and are not covered by
the warranty.
This manufacturer’s guarantee does not affect the user’s existing
warranty claims against the dealer/seller.
If a claim under the warranty arises, please send the defective
piece of equipment together with a copy of the proof of
purchase and a description of the fault, postage paid, to the
Service Address stated on the back.
We will return the piece of equipment to you free of charge on
completion of the repair.
25
GB
GARDENA guarantees this product for 2 years (from date of
purchase).
1763-04_Konform
D
25.04.2007
Produkthaftung
GB Product Liability
F
Responsabilité
NL Productaansprakelijkheid
11:24 Uhr
Seite 110
Wir weisen ausdrücklich darauf hin, dass wir nach dem Produkthaftungsgesetz nicht für durch unsere Geräte hervorgerufene Schäden einzustehen
haben, sofern diese durch unsachgemäße Reparatur verursacht oder bei
einem Teileaustausch nicht unsere originale GARDENA Teile oder von uns
freigegebene Teile verwendet wurden und die Reparatur nicht vom
GARDENA Service oder dem autorisierten Fachmann durchgeführt wird.
Entsprechendes gilt für Ergänzungsteile und Zubehör.
We expressly point out that, in accordance with the product liability law,
we are not liable for any damage caused by our units if it is due to improper repair or if parts exchanged are not original GARDENA parts
or parts approved by us, and, if the repairs were not carried out by a
GARDENA Service Centre or an authorised specialist. The same applies
to spare parts and accessories.
Nous vous signalons expressément que GARDENA n’est pas responsable des dommages causés par ses appareils, dans la mesure où ces
dommages seraient causés suite à une réparation non conforme, dans la
mesure où, lors d’un échange de pièces, les pièces d’origine GARDENA
n’auraient pas été utilisées, ou si la réparation n’a pas été effectuée par
le Service Après-Vente GARDENA ou l’un des Centres SAV agréés
GARDENA. Ceci est également valable pour tout ajout de pièces et
d’accessoires autres que ceux préconisés par GARDENA.
Wij wijzen er nadrukkelijk op, dat wij op grond van de wet aansprakelijkheid voor producten niet aansprakelijk zijn voor schade ontstaan door onze
apparaten, indien deze door onvakkundige reparatie veroorzaakt zijn, of er
bij het uitwisselen van onderdelen geen gebruik gemaakt werd van onze
originele GARDENA onderdelen of door ons vrijgegeven onderdelen en de
reparatie niet door de GARDENA technische dienst of de bevoegde vakman uitgevoerd werd. Ditzelfde geldt voor extra-onderdelen en accessoires.
S
Produktansvar
Tillverkaren är inte ansvarig för skada som orsakats av produkten om
skadan beror på att produkten har reparerats felaktigt eller om, vid reparation eller utbyte, andra än Original GARDENA reservdelar har använts.
Samma sak gäller för kompletteringsdelar och tillbehör.
I
Responsabilità
del prodotto
Si rende espressamente noto che, conformemente alla legislazione sulla
responsabilità del prodotto, non si risponde di danni causati da nostri articoli se originati da riparazioni eseguite non correttamente o da sostituzioni
di parti effettuate con materiale non originale GARDENA o comunque da
noi non approvato e, in ogni caso, qualora l’intervento non venga eseguito
da un centro assistenza GARDENA o da personale specializzato autorizzato. Lo stesso vale per le parti complementari e gli accessori.
E
Responsabilidad
de productos
Advertimos que conforme a la ley de responsabilidad de productos no nos
responsabilizamos de daños causados por nuestros aparatos, siempre y
cuando dichos daños hayan sido originados por arreglos o reparaciones
indebidas, por recambios con piezas que no sean piezas originales
GARDENA o bien piezas no autorizadas por nosotros, así como en aquellos
casos en que la reparación no haya sido efectuada por un Servicio Técnico GARDENA o por un técnico autorizado. Lo mismo es aplicable para
las piezas complementarias y accesorios.
P
Responsabilidade
sobre o produto
Queremos salientar que segundo a lei da responsabilidade do fabricante,
nós não nos responsabilizaremos por danos causados pelo nosso equipamento, quando estes ocorram em decorrência de reparações inadequadas
ou da substituição de peças por peças não originais da GARDENA, ou peças não autorizadas. A responsabilidade tornar-se-à nula também depois
de reparações realizadas por oficinas não autorizadas pela GARDENA.
Esta restrição valerá também para peças adicionais e acessórios.
DK Produktansvar
110
Vi gør udtrykkeligt opmærksom på at i henhold til produktansvarsloven
er vi ikke ansvarlige for skader forårsaget af vores udstyr, hvis det er på
grund af uautoriserede reparationer eller hvis dele er skiftet ud og der ikke
er anvendt originale GARDENA dele eller dele godkendt af os, eller hvis
reparationerne ikke er udført af GARDENA-service eller en autoriseret
fagmand. Det samme gælder for ekstra udstyr og tilbehør.
1763-04_Konform
D
25.04.2007
11:24 Uhr
Seite 111
EU-Konformitätserklärung
MaschinenVerordnung (9. GSGVO) / EMVG / Niedersp. RL
Der Unterzeichnete GARDENA Manufacturing GmbH · Hans-Lorenser-Straße 40,
D-89079 Ulm bestätigt, dass die nachfolgend bezeichneten Geräte in der von
uns in Verkehr gebrachten Ausführung die Anforderungen der harmonisierten
EU-Richtlinien, EU-Sicherheitsstandards und produktspezifischen Standards
erfüllen. Bei einer nicht mit uns abgestimmten Änderung der Geräte verliert
diese Erklärung ihre Gültigkeit.
Bezeichnung des Gerätes:
Description of the unit:
Désignation du matériel :
Omschrijving van het apparaat:
Produktbeskrivning:
Descrizione del prodotto:
Descripción de la mercancía:
Descrição do aparelho:
Beskrivelse af enhederne:
Hauswasserautomat
Pressure Tank Unit
Pompe d’arrosage automatique
Hydrofoorpomp
Pumpautomat
Pompa a intervento automatico
Bomba doméstico
Bomba de Pressão
Husvandværk
Typ:
Type:
Type :
Typ:
Typ:
Modello:
Tipo:
Tipo:
Type:
Art.-Nr.:
Art. No.:
Référence :
Art. nr.:
Art. nr.:
Art.:
Art. No:
Art. No:
Varenr.:
GB EU Certificate of Conformity
The undersigned GARDENA Manufacturing GmbH · Hans-Lorenser-Str. 40 ·
D-89079 Ulm hereby certifies that, when leaving our factory, the units indicated below are in accordance with the harmonised EU guidelines, EU standards
of safety and product specific standards. This certificate becomes void if the
units are modified without our approval.
F
Certificat de conformité aux directives européennes
Le constructeur, soussigné : GARDENA Manufacturing GmbH · Hans-LorenserStr. 40 · D-89079 Ulm déclare qu’à la sortie de ses usines le matériel neuf
désigné ci-dessous était conforme aux prescriptions des directives européennes énoncées ci-après et conforme aux règles de sécurité et autres règles qui
lui sont applicables dans le cadre de l’Union européenne. Toute modification
portée sur ce produit sans l’accord express de GARDENA supprime la validité
de ce certificat.
NL EU-overeenstemmingsverklaring
Ondergetekende GARDENA Manufacturing GmbH · Hans-Lorenser-Str. 40 ·
D-89079 Ulm bevestigt, dat de volgende genoemde apparaten in de door ons
in de handel gebrachte uitvoering voldoen aan de eis van, en in overeenstemming zijn met de EU-richtlijnen, de EU-veiligheidsstandaard en de voor het
product specifieke standaard. Bij een niet met ons afgestemde verandering
aan de apparaten verliest deze verklaring haar geldigheid.
S
EU Tillverkarintyg
Undertecknad firma GARDENA Manufacturing GmbH · Hans-Lorenser-Straße
40 · D-89079 Ulm intygar härmed att nedan nämnda produkter överensstämmer med EU:s direktiv, EU:s säkerhetsstandard och produktspecifikation. Detta
intyg upphör att gälla om produkten ändras utan vårt tillstånd.
I
Dichiarazione di conformità alle norme UE
La sottoscritta GARDENA Manufacturing GmbH · Hans-Lorenser-Str. 40 ·
D-89079 Ulm certifica che il prodotto qui di seguito indicato, nei modelli da
noi commercializzati, è conforme alle direttive armonizzate UE nonché agli
standard di sicurezza e agli standard specifici di prodotto. Qualunque modifica
apportata al prodotto senza nostra specifica autorizzazione invalida la presente dichiarazione.
E
Declaración de conformidad de la UE
El que subscribe GARDENA Manufacturing GmbH · Hans-Lorenser-Str. 40 ·
D-89079 Ulm declara que la presente mercancía, objeto de la presente declaración, cumple con todas las normas de la UE, en lo que a normas técnicas, de
homologación y de seguridad se refiere. En caso de realizar cualquier modificación en la presente mercancía sin nuestra previa autorización, esta declaración pierde su validez.
P
4000/4
4000/5
5000/5
6000/5
LCD
LCD
LCD
Inox LCD
EU-Richtlinien:
EU directives:
Directives européennes :
EU-richtlijnen:
EU direktiv:
Direttive UE:
Normativa UE:
Directrizes da UE:
EU Retningslinier:
Schall-Leistungspegel:
Noise level:
Puissance acoustique :
Geluidsniveau:
Ljudnivå:
Livello rumorosità:
Nivel sonoro:
Nível de ruido:
Lydtryksniveau:
1763
1765
1767
1769
74
76
80
74
1763
1765
1767
1769
98/37/EG : 1998
2006/42/EG : 2006
2004/108/EG
2006/95/EG
93/68/EG
2000/14/EG
gemessen / garantiert
measured / guaranteed
mesurée / garantie
gemeten / gegarandeerd
uppmätt / garanterad
testato / garantito
medido / garantizado
medido / garantido
afmålt / garanti
dB (A)
dB (A)
dB (A)
dB (A)
/
/
/
/
75
79
81
77
Anbringungsjahr der CE-Kennzeichnung:
Year of CE marking:
Date d’apposition du marquage CE :
Installatiejaar van de CE-aanduiding:
CE-Märkningsår:
Anno di rilascio della certificazione CE:
Colocación del distintivo CE:
Ano de marcação pela CE:
CE-Mærkningsår:
dB
dB
dB
dB
(A)
(A)
(A)
(A)
2004
Certificado de conformidade da UE
Os abaixo mencionados GARDENA Manufacturing GmbH · Hans-Lorenser-Str.
40 · D-89079 Ulm Por este meio certificam que ao sair da fábrica os aparelhos abaixo mencionados estão de acordo com as directrizes harmonizadas
da UE, padrões de segurança e de produtos específicos. Este certificado
ficará nulo se as unidades forem modificadas sem a nossa aprovação.
DK EU Overensstemmelse certificat
Undertegnede GARDENA Manufacturing GmbH · Hans-Lorenser-Str. 40 ·
D-89079 Ulm bekræfter hermed, at enheder listet herunder, ved afsendelse fra
fabrikken, er i overensstemmelse med harmoniserede EU retningslinier, EU
sikkerheds standarder og produkt specifikations standarder. Dette certifikat
træder ud af kraft hvis enhederne er ændret uden vor godkendelse.
Peter Lameli
Ulm, den 12.07.2004
Ulm, 12.07.2004
Fait à Ulm, le 12.07.2004
Ulm, 12.07.2004
Ulm, 2004.07.12
Ulm, 12.07.2004
Ulm, 12.07.2004
Ulm, 12.07.2004
Ulm, 12.07.2004
Technische Leitung
Technical Dept. Manager
Direction technique
Technisch directeur
Technical Director
Direzione Tecnica
Dirección Técnica
Director Técnico
Teknisk direktør
111
1763-04_Konform
25.04.2007
11:24 Uhr
Seite 112
Pumpen-Kennlinie:
m
Performance
characteristics
Courbes de performance
40
Prestatiegrafiek
30
Pumpens kännetecken
20
Curva di rendimento
10
Curva característica
de la bomba
0
Características
de performance
bar
50
00
/5
LC
D
50
Ydelses karakteristika
4
40
00
/4
LC
D
3
40
00
/5
0
D
5
1000
2000
LC
D
3000
2
60
00
/5
Ino
xL
CD
4000
5000
1
6000
l/h
Die Leistungsdaten der Pumpenkennlinie sind gemessen bei einer
Saughöhe von 0,5 m und unter Verwendung eines 25 mm (1”)Saugschlauchs.
GB Technical data of the above performance e characteristics is measured at a suction height of 0.5 m using a 25 mm (1”) suction
hose.
F
Les performances ont été déterminées avec une hauteur d’aspiration de 0,5 m et en utilisant un tuyau d’aspiration de Æ int. 25
mm.
NL De capaciteitsgegevens in de grafiek zijn gemeten bij een
aanzuighoogte van 0,5 m en bij gebruik van een 25 mm (1”)aanzuigslang.
S
Värdena ovan är utmätta på en sughöjd av 0,5 m med 25 mm (1”)
sugslang.
I
Le prestazioni indicate nella curva di rendimento presuppongono
un’altezza di aspirazione pari a 0,5 m e l’impiego di un tubo da
25 mm (1”).
E
Los datos de rendimiento de la curva característica de la bomba
se han medido con una altura de succión de 0,5 m y con una
manguera de succión de 25 mm (1”).
P
A informação técnica com as características de performance
acima descritas foram medidas com uma altura de sucção de
0,5 m, com uma mangueira de sucção de25 mm (1”).
DK Tekniske data for de ovennævnte ydelses karakteristika er målt
ved en sugehøjde på 0,5 m og en sugeslange på 25 mm (1”).
112
1763-04_Konform
25.04.2007
Deutschland/Germany
GARDENA Manufacturing GmbH
Service Center
Hans-Lorenser-Straße 40
D-89079 Ulm
Produktfragen: (+49) 731 490-123
Reparaturen: (+49) 731 490-290
service@gardena.com
Argentina
Argensem S.A. Calle Colonia
Japonesa s/n - (1625) Loma
Verde, Escobar, Buenos Aires
Phone: (+54) 34 88 49 40 40
info@argensem.com.ar
Australia
Nylex Consumer Products
50-70 Stanley Drive
Somerton, Victoria, 3062
Phone: 1800 658 276
spare.parts@nylex.com.au
Austria/Österreich
GARDENA Österreich Ges.m.b.H.
Stettnerweg 11-15
2100 Korneuburg
Tel.: (+43) 22 62 745 45-36 od. -30
kundendienst@gardena.at
Belgium
GARDENA Belgium NV/SA
Sterrebeekstraat 163
1930 Zaventem
Phone: (+32) 27 20 921 2
info@gardena.be
Brazil
Palash Comércio e Importação Ltda.
Rua Américo Brasiliense,
2414 - Chácara Sto Antonio
São Paulo - SP - Brasil CEP 04715-005
fone: 55 11 5181-0909
fax: 55 11 5181-2020
Bulgaria
Sofia 1404 Bulgaria
2 Luis Ahalier Str.
7th floor, DENEX LTD.
Phone: (+359) 2 9581821
office@denex-bg.com
Canada
GARDENA Canada Ltd. 100,
Summerlea Road Brampton,
Ontario, L6T 4X3
Phone: (+1) 905 792 93 30
info@gardenacanada.com
Chile
Antonio Martinic Y CIA. LTDA.
Gilberto Fuenzalida 185 Loc.
Las Condes, Santiago de Chile
Phone: (+56) 2 20 10 708
garfar_cl@yahoo.com
Costa Rica
Compania Exim Euroiberoamericana S.A. Los Colegios, Moravia,
200 metros al Sur del Colegio
Saint Francis, San José, Costa
Rica. Phone: (+506) 297 68 83
exim_euro@racsa.co.cr
116
11:24 Uhr
Seite 116
Croatia
KLIS d.o.o., Stančičeva 79
10419 Vukovina
Phone: (+385) 1 622 777 0
gardena@klis-trgovina.hr
Cyprus
FARMOKIPIKI LTD
P.O. Box 7098
74, Digeni Akrita Ave.
1641 Nicosia
Phone: (+357) 22 75 47 62
condam@spidernet.com.cy
Czech Republic
GARDENA spol. s.r.o.
¤ípská 20a, ã.p. 1153
62700 Brno
Phone: (+420) 800 100 425 (Hotline)
gardena@gardenabrno.cz
Denmark
GARDENA Norden AB
Box 9003, 200 39 Malmö, Sverige
info@gardena.dk
Finland
Habitec Oy, Martinkyläntie 52
01720 Vantaa
Italy
GARDENA Italia S.p.A.
Via Donizetti 22,
20020 Lainate (Mi)
Phone: 02.93.94.79.1
info@gardenaitalia.it
Japan
KAKUICHI Co. Ltd.
Yamato Bldg. 5-3-1
Kojimachi Chiyoda-ku.
Tokyo 102-0083
Phone: (+81)-(0)3-3264-4721
m_ishihara@kaku-ichi.co.jp
Luxembourg
Magasins Jules Neuberg
39, rue Jacques Stas
Luxembourg-Gasperich 2549
Case Postale No. 12
Luxembourg 2010
Phone +352-40 14 01
api@neuberg.lu
Netherlands
GARDENA Nederland BV
Postbus 50176
1305 AD ALMERE
Phone: (+31) 36 521 00 00
info@gardena.nl
France
GARDENA France
Service Après-Vente
BP 50080
95948 ROISSY CDG Cedex
Tél.: (+33) 0826 101 455
service.consommateurs@gardena.fr
Neth. Antilles
Jonka Enterprises N.V.
Sta. Rosa Weg 196
P.O. Box 8200, Curaçao
Phone: (+599) 9 767 66 55
pgm@jonka.com
Great Britain
GARDENA UK Ltd.
27-28 Brenkley Way
Blezard Business Park
Seaton Burn
Newcastle upon Tyne NE13 6DS
info@gardena.co.uk
New Zealand
NYLEX New Zealand Ltd.
Building 2
118 Savill Drive
Mangere, Auckland
Phone: 0800 22 00 88
spare.parts@nylex.com.au
Greece
Agrokip - Psomadopoulos S.A.
Ifaistou 33A - Ind. Area Koropi,
194 00 Athens Greece
V.A.T. EL093474846
Phone: (+30) 210 66 20 225
info@agrokip.gr
Norway
GARDENA Norden AB
Karihaugveien 89, 1086 Oslo
Hungary
GARDENA Magyarország Kft.
Késmárk utca 22
1158 Budapest
Phone: (+36) 80 20 40 33 (Hotline)
gardena@gardena.hu
Iceland
Ó. Johnson & Kaaber
Tunguhalsi 1
110 Reykjavik
Ireland
Michael McLoughlin & Sons
Hardware Limited, Long Mile Road
Dublin 12
Poland
GARDENA Polska Sp. z o.o.
Szymanów 9d, 05-532 Baniocha
Phone: (+48) 22 727 56 90
gardena@gardena.pl
Portugal
GARDENA, Lda.
Recta da Granja do Marquês
Edif. GARDENA Algueirão,
2725-596 Mem Martins
Phone: 219228530
info@gardena.pt
Romania
MADEX INTERNATIONAL SRL
Soseaua Odaii 117-123, sector 1
Bucuresti, RO 013603
Phone: (+40) 21 352 760 3/4/5/6
madex@ines.ro
Russia/Россия
АO AMИДА ТТЦ
ул. Мосфилмовская 66
117330 Москва
Phone: +7 495 647 25 10
amida@col.ru
Singapore
Hy-Ray Private Limited
40 JALAN PEMIMPIN
#02-08 Tat Ann Building
Singapore 577 185
Phone: (65) 6253 2277
hyray@singnet.com.sg
Slovak Republic
GARDENA Slovensko, s. r. o.
Panónska cesta 17
851 04 Bratislava
Phone: (+421) 263 453 722
info@gardena.sk
Slovenia
GARDENA d.o.o., Brodišče 15, 1236 Trzin
Phone: (+386) 1 580 93 32
servis@gardena.si
South Africa
GARDENA South Africa (Pty.) Ltd.
P.O. Box 11534, Vorna Valley 1686
Phone: (+27) 11 315 02 23
sales@gardena.co.za
Spain
GARDENA IBÉRICA S.L.
C/Basauri, no¯ 6
La Florida, 28023 Madrid
Phone: (+34) 91 708 05 00 (4 líneas)
atencioncliente@gardena.es
Sweden
GARDENA Norden AB
Box 9003, 20039 Malmö
info@gardena.se
Switzerland/Schweiz
GARDENA Schweiz AG
Bitziberg 1, 8184 Bachenbülach
Tel.: (+41)-848 800 464
info@gardena.ch
Turkey
GARDENA/Dost Diș Ticaret
Mümessillik A.Ș. Sanayi
Çad. Adil Sokak No. 1
Kartal - Istanbul
Ukraine
ALTSEST JSC
4 Petropavlivska Street
Petropavlivska Borschahivka Town
Kyivo Svyatoshyn Region
08130 Ukraine
Phone: +380 44 4595703
upyr@altsest.kiev.ua
USA
Melnor, 3085 Shawnee Drive
Winchester, VA 22604
Phone: (540) 722-9080
service_us@melnor.com
1763-20.960.05/0407
© GARDENA Manufacturing GmbH
D-89070 Ulm
http://www.gardena.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement