Caple Wi3122 & Wi3122WH Wine Cabinet Instruction Manual

Caple Wi3122 & Wi3122WH Wine Cabinet Instruction Manual
undercounter wine cabinet
instruction manual
WI3122 & WI3122WH
Contact Caple on 0117 938 7420 or for spare parts www.caple.co.uk
Wi3122_Wi3122WH Wine Cabinet manual.indd 1
24/10/2016 10:05
CONTENTS
Important safety instructions
2
Installation instructions
8
Before using your wine cabinet
8
Operating and setting the temperature
10
Control Panel
10
Using the shelves
12
How to change the door opening
13
Installing the bar handle
14
Fitting a kitchen plinth
15
Wine bottle stacking
16
Installation dimensions
17
Fixing the top fixing bracket
17
Using the foot sliders
18
Care and maintenance
19
Troubleshooting guide
21
Defrosting/condensation
22
The humidity system
22
Recommended storage temperatures
22
Recommended drinking temperatures
22
Technical data
23
Please keep this instruction manual for future reference
2
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 2
24/10/2016 10:05
INTRODUCTION
Thank you for buying your new Caple Wine Cabinet.
To ensure that you get the best results from your new purchase, we strongly suggest
that you read this instruction manual thoroughly before use. This manual contains
installation advice, usage instructions and other important facts about your Caple
Wine Cabinet. If treated with care your Caple Wine Cabinet will give you many years
of trouble free use.
Please keep this instruction manual for future reference
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 3
3
24/10/2016 10:05
WARNINGS
--To prevent damaging the door gasket, make sure the
door is fully open when pulling shelves out of the rail
compartment.
--The appliance must be positioned so that the plug is
accessible. Release the electric cord and move your
cabinet to its final location. Do not move your cabinet
while loaded with wine as you may distort the body.
--The wine cabinet should be installed in a suitable place
in order to avoid touching the compressor.
--After unpacking, make sure that the appliance is in
perfect order. If you have any doubt, do not use it and
contact your retailer.
--If the supply cord is damaged, it must be replaced by
a Caple service agent or a similarly qualified person in
order to avoid a hazard.
--This product is not designed for commercial use, it is a
household appliance only.
It is not intended to be used in:
•
•
•
Staff kitchen areas in shops, offices and other working
environments
Bed and breakfast type environments
By clients in hotels, motels and any other residential
type environments
Please keep this instruction manual for future reference
4
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 4
24/10/2016 10:05
--This appliance is intended to be used exclusively for the
storage of wine.
IMPORTANT
Caple cannot be held liable for any non
compliance with these instructions.
ELECTRICAL SHOCK HAZARD
To reduce the risk of fire, electrical shock, or injury when using
your appliance, follow these basic precautions:
--Read all instructions before using the wine cabinet.
--DANGER or WARNING: Risk of child entrapment.
--Before you throw away your old wine cabinet: Take off
the door, leaving the shelves in place so that children
cannot easily climb inside.
--Never allow children to operate, play with, or crawl
inside the appliance.
--Never clean appliance parts with flammable fluids. The
fumes can create a fire hazard or explosion.
--Do not store or use gasoline or any other flammable
vapours and liquids in the vicinity of this or any other
appliance. The fumes can create a fire hazard or
explosion.
Please keep this instruction manual for future reference
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 5
5
24/10/2016 10:05
--The refrigerant of this appliance is R600a, flammable
and explosive articles should not be put in or near the
cabinet, to avoid the risk of fire or explosion.
--This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance.
--Cleaning and user maintenance shall not be made by
children without supervision.
Please keep this instruction manual for future reference
6
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 6
24/10/2016 10:05
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household waste. Please
recycle where facilities exist. Check with your Local Authority or retailer for recycling
advice. This appliance is marked according to the European directive 2002/96/EC on
Waste Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product. The symbol
on the product indicates that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection point for the recycling of
electrical and electronic equipment. Disposal must be carried out in accordance with
local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this
product, please contact your local council, your household waste disposal service or
the retailer where you purchased the product
CE DECLARATIONS OF CONFORMITY
This appliance has been manufactured to the strictest standards and complies
with all applicable legislation, Low Voltage Directive (LVD) and Electromagnetic
Compatibility (EMC).
Please keep this instruction manual for future reference
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 7
7
24/10/2016 10:05
INSTALLATION
Before using your wine cabinet
-- Remove the exterior and interior packing.
-- IMPORTANT: Before connecting the wine cabinet to the power source, let it stand
upright for at least 12 hours. This will reduce the possibility of a malfunction in the
cooling system from handling during transportation.
-- Clean the interior surface with lukewarm water using a soft cloth.
Before installation, turn the unit off and unplug it from the outlet.
NOTE
To protect the appliance in transit and delivery the door is packed tightly against the
cabinet. When first installed this can mean the door seal appears thinner on one
side of the door due to compression, this is normal and once out of the box it will
relax over a short period of time and the door will return to the normal position. If
you wish to speed up the process you can gently warm the seal with a hair dryer on
a low temperature setting. This can help relax the seal helping it return to normal
thickness a little faster.
INSTALLATION OF YOUR WINE CABINET
-- Place your wine cabinet on a floor that is strong enough to support it when it is
fully loaded.
-- To level your wine cabinet, adjust the front levelling leg at the bottom of the
cabinet.
-- Ensure it is perfectly level, as this will minimise any vibrations.
-- This appliance uses flammable refrigerant. Never damage the cooling pipework
during transportation.
-- Locate the wine cooler away from direct sunlight and sources of heat (ovens,
hobs, heaters, radiators, etc.). Never clean appliance parts with flammable fluids.
The fumes can create a fire hazard or explosion. When disposing your appliance,
please choose an authorized disposal site.
-- Avoid locating the unit in moist areas.
-- It is fitted with a power cord having an earth wire terminating in a 13amp plug.
-- Ensure the product is correctly ventilated (see page 15).
Please keep this instruction manual for future reference
8
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 8
24/10/2016 10:05
-- Consult a qualified electrician or service engineer if the earthing instructions are
not completely understood.
-- Plug the wine cabinet into an exclusive, properly installed-grounded wall outlet.
Do not under any circumstances cut or remove the third (ground) pin from the
plug. Any questions concerning power and/or grounding should be directed
toward a certified electrician or Caple service.
WARNING: INCORRECT EARTHING CAN RESULT IN THE
RISK OF ELECTRIC SHOCK
Attention!
-- Store wine in sealed bottles
-- Do not overload the cabinet
-- Do not open the door unless necessary
-- Do not cover shelves with aluminium foil or any other shelf material which may
prevent air circulation
-- Should the wine cabinet be stored without use for long periods it is suggested,
after careful cleaning, to leave the door ajar to allow air to circulate inside the
cabinet in order to avoid possible formations of condensation, mould or odours.
-- Keep ventilation openings, in the appliance enclosure or in the built-in structure,
clear of obstruction;
-- Do not use mechanical devices or other means to accelerate the defrosting
process, other than those recommended by the manufacturer;
-- Do not damage the refrigerant circuit;
-- Do not use electrical appliances inside the storage compartments of the appliance,
unless they are the type recommended by the manufacturer
Please keep this instruction manual for future reference
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 9
9
24/10/2016 10:05
OPERATING YOUR WINE CABINET
Please use the cabinet within ambient temperatures between 16-32ºC, if the
ambient temperature is higher or lower than this, it will cause the temperature to
fluctuate in the cabinet, possibly preventing it from reaching 5-18ºC.
SETTING THE TEMPERATURE
To set the temperature, connect the power cord to a properly grounded outlet. In
the event of a power interruption, the previous temperature setting is automatically
erased and it will default to a preset temperature setting of 12°C
Set the desired cooling temperature by pressing the buttons adjacent to the /
indicators. Each press of the buttons will scroll through the available temperature
settings in increments of 1°C.
The temperature setting can be adjusted from 5°C to 18°C
To view the actual temperature at anytime press and hold the temperature
adjustment button (up or down) for approximately 5 seconds, the actual
temperature will temporarily flash in the LED display for 5 Seconds. After this it will
revert back to the set temperature.
Flashing LED = Cabinet temperature
Steady LED = Set temperature
NOTE
If the unit is unplugged, power lost or turned off, you must wait 3 to 5 minutes
before restarting the unit. If you attempt to restart before this time delay, the wine
cabinet will not start.
When you use the wine cabinet for the first time or you restart the cabinet after
having been shut off for a long time, there could be a few degrees variance
between the temperature you select and the one indicated on the LED readout. This
is normal and it is due to the length of the activation time. Once the wine cabinet
has been running for a few hours everything will be back to normal.
Please keep this instruction manual for future reference
10
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 10
24/10/2016 10:05
Control panel
Control panel
•
CONTROL PANEL
Indicator
light illuminates to signify the cooling mode is currently in operation
“
”
Indicator
light illuminates to signify the cooling mode is currently in operation.
“
” Button
Used
to switch to
thesignify
internalthe
light
on/off mode is currently in operation.
Indicator
illuminates
cooling
• “ light
”Button
•
Used toButton
switch the internal light on/off.
“
”Button
To switch the appliance on/off
Used
switch
the internal
light
on/off.
(press
hold mode
this
buttons
for approximately
3 seconds)
• to
“tosignify
” Button
minates
theand
cooling
is currently
in operation.
To switch
the appliance on/off (press and hold this buttons for approximately 3 second
Button
• “
” Button
Used to raise the temperature in 1ºC increments
To
appliance on/off (press and hold this buttons for approximately 3 seconds).
• switch
“ lightthe
”on/off.
Button
e internal
Used toButton
raise the temperature in 1ºC increments.
• “ to”signify
Button
Used
lower the
temperature
by in
increments
minates
thetocooling
mode
is currently
in1ºC
operation.
Used
to
raise
the
temperature
in
1ºC
increments.
• on/off
“
” Button
liance
(press
and hold this buttons for approximately 3 seconds).
Used to lower the temperature by in 1ºC increments.
•e internal
“
”light
Button
on/off.
ode Used
is currently
currently
in operation.
operation.
ode
is
in
to lower
the temperature by in 1ºC increments.
temperature
1ºCtemperature
increments.
Settinginthe
•
Setting
the(press
temperature
liance on/off
and hold this buttons for approximately 3 seconds).
• To set the temperature, connect the power cord to a properly grounded outlet. In the
e temperature
by in
1ºC increments.
a power
interruption,
the previous temperature setting is automatically erased and it wi
• To set
temperature,
connect
the
to athe
preset
temperature
setting
of power
12°C cord to a properly grounded outlet. In the even
a
power
interruption,
the
previous
temperature
setting is automatically erased and it will de
temperature in 1ºC increments.
erature
his
for
approximately
3
seconds).
his buttons
buttons
for
approximately
3
seconds).
to• a preset
setting
of 12°C
Set thetemperature
desired cooling
temperature
by pressing the buttons adjacent to the “
/
press
scroll through
thethe
available
temperature settin
erature, indicators.
connect theEach
power
cordoftothe
a buttons
properlywill
grounded
outlet. In
event of
•temperature
Set increments
the desired
temperature by pressing the buttons adjacent to the “
/
eion,
by intemperature
1ºC
increments.
ofcooling
1°C.
the previous
setting is automatically erased and it will default
indicators. Each press of the buttons will scroll through the available temperature settings in
erature setting of 12°C
increments
of 1°C.
erature
• The temperature
setting can be adjusted from 5°C to 18°C
cooling
temperature
by
pressing
the buttons adjacent to the “
/
"
nts.
nts.
• The
temperature
settingtemperature
can to
beaadjusted
from
5°C
tooutlet.
18°Chold
erature,
connect
power
cord
properly
grounded
In
the
event
of
•
To
view
the
actual
at
anytime
press
and
temperature
adjustment b
press of the buttons will scroll through the available temperature settings in
ion,
the
previous
temperature
setting
is
automatically
erased
and
it
will
default
(up or down) for approximately 5 seconds, the actual temperature will temporarily flash i
C.
• To setting
view
anytime
and hold
temperature
adjustment butto
erature
ofactual
12°C
LEDthe
display
fortemperature
5 Seconds. at
After
this it press
will revert
backthe
to the
set temperature.
(up
or
down)
for
approximately
5
seconds,
the
actual
temperature
will
temporarily
flash in the
edsetting
can be grounded
adjusted
from
5°C
tothe
18°C
Flashing
LED = Cabinet
temperature
to
a
outlet.
In
event
of
Please keep
this
instruction
manual for future reference
dcooling
toLED
a properly
properly
grounded
outlet.
In
the
event
of
display
for
5
Seconds.
After
this
it
will
revert
back
to
the
set
temperature.
temperature
pressing
the buttons adjacent to the “
/
"
LED =by
Set
temperature
setting
isSteady
automatically
erased
and itit will
will default
default
setting
is
automatically
erased
and
Flashing
LED
=
Cabinet
temperature
press
of
the
buttons
will
scroll
through
the
available
temperature
settings
in
al temperature at anytime press and hold
the temperature
button
Instruction
manual adjustment
Wi3122 & Wi3122WH
11
Steady LED
= Set temperature
C.
approximately
5 seconds,
the actual temperature will temporarily flash in the
Seconds.
Afteradjacent
this it willto
revert
ng
the
buttons
the
““back to// the set"" temperature.
ng
the Wi3122_Wi3122WH
buttons
to
the5°C
e
setting
can be adjacent
adjusted
from
to 18°C
Wine Cabinet
manual.indd
24/10/2016 10:05
Note
Cabinet
temperature
hrough the available temperature11settings in
Internal light
In order to reduce energy consumption, the LED light within this wine cabinet will
automatically switch off after 10 minutes. If you would prefer the LED light to
remain on continuously, this is possible. Please press and hold the “LIGHT” button
for 5 seconds, the display will show “LP”. After 4 seconds the display will revert
back
to normal
Internal
light and the light will remain on until manually switched off.
order
to reduce
consumption,
theconserve
LED light within
this(recommended),
wine cabinet will automatically
IfInyou
would
likeenergy
to revert
back and
energy
press and
switch off after 10 minutes. If you would prefer the LED light to remain on continuously, this is
hold
the
“LIGHT”
button
for
5
seconds,
the
display
will
show
“LF”.
After
4 seconds
possible. Please press and hold the "LIGHT" button for 5 seconds, the display will show "LP".
After
4 seconds
display
will back
revert to
back
to normal
andthe
thelight
light will
on until manually
the
displaythewill
revert
normal,
and
willremain
automatically
switchswitched
off
off. 10 minutes.
after
If you would like to revert back and conserve energy (recommended), press and hold the "LIGHT"
button for 5 seconds, the display will show "LF". After 4 seconds the display will revert back to
USING
normal, andTHE
the lightSHELVES
will automatically switch off after 10 minutes.
To prevent damaging the door gasket, make sure to have the door opened fully
when
shelves out of the rail compartment.
Usingpulling
the shelves
• easy
To prevent
damaging
the door gasket,
make
sure
to have
door
openedapproximately
fully when pulling1/3
For
access
to the storage
content,
you
must
pullthethe
shelves
shelves out of the rail compartment.
out of
the rail compartment, however this unit was designed with a notch on each
• For easy access to the storage content, you must pull the shelves approximately 1/3 out of the rail
sidescompartment,
of the shelfhowever
tracks to
bottles from
thisprevent
unit was designed
with afalling.
notch on each sides of the shelf tracks to
prevent bottles from falling.
Removing or installing shelves
Removing or installing shelves
To install or remove a shelf, tilt the shelf as per the diagram and simply pull out, or
• To
or remove
tilt the
as perbrackets
the diagram
and simply pull out, or push in
push
ininstall
the shelf
until aitshelf,
sits on
theshelf
support
securely.
the shelf until it sits on the support brackets securely.
• Visit
Caple
websiteto
to view
view aa'How
to video'
on this.
Visit
our our
Caple
website
‘How
to video’
on www.caple.co.uk
this. www.caple.co.uk
Please keep this instruction manual for future reference
12
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 12
24/10/2016 10:05
How to change the door opening
This appliance has reversible doors but is delivered with a right hinged door. The left hand
hinge kit comes with the unit (in the box), should you wish to reverse the hinge on your unit
follow the directions below:
HOW TO CHANGE THE DOOR OPENING
1. Lower
hinge (Right)
. Screwsbut is delivered with
3 .Door
axishinged door. The
This
appliance
has reversible2 doors
a right
4.
Door
5.
Top
hinge
(Right)
6.
Hinge
Screws
left hand hinge kit comes with the unit (in the box), should you
wish to reverse the
7. Top hinge (Left)
8. Decorative plugs
9. Lower hinge (Left)
hinge on your unit follow the directions below:
10. Door limit device
11. Screw
12. Plug
1. Lower hinge (Right)
4. Door
7. Top hinge (Left)
10. Door limit device
2 . Screws
5. Top hinge (Right)
8. Decorative plugs
11. Screw
3 .Door axis
6. Hinge Screws
9. Lower hinge (Left)
12. Plug
1. Open the door to 90 degrees, take out 2 screws (2) from lower door axis (3), remove the door (4),
1.then
Open
door
toand
90 door
degrees,
take
pullthe
out the
door
axis (Fig.
A).out 2 screws (2) from lower door axis (3),
2. Put
the door
safely
take
outout
the the
plugdoor
(12) from
of door
unscrew 1 screw
remove
thedown
door
(4), and
then
pull
andtop
door
axis frame,
(Fig. A).
(11) at bottom and remove the door limit device (10), then install the door limit device (10) at top
2.ofPut
the
door
down
taketoout
the
top
of door
frame,
door
frame,
please
usesafely
spare and
plug (12)
block
theplug
hole (12)
at topfrom
of door
frame.
(Fig. A/B)
3. Take
out 3 hinge
screws
(6)at
from
top hinge
(5) and
(Fig.device
C)
unscrew
1 screw
(11)
bottom
and(right)
remove
theremove
door it.
limit
(10), then
4. Remove decorative nail (8) from left top of cabinet and install spare top hinge (Left) (7) at left top
install the door limit device (10) at top of door frame, please use spare plug (12)
of cabinet with 3 screws. (Fig. D)
to blockabove
the hole
at topinstall
of door
(Fig. (left)
A/B)(9). (Fig. E)
5. According
procedure,
spareframe.
lower hinge
6. The door revolves 180 degrees, install the door with same way it was removed and fix it with door
3.aligned.
Take out 3 hinge screws (6) from top hinge (right) (5) and remove it. (Fig. C)
7. Block the hole at right top of cabinet with spare decorative plugs (8).
4. Remove decorative nail (8) from left top of cabinet and install spare top hinge
(Left) (7) at left top of cabinet with 3 screws. (Fig. D)
5. According above procedure, install spare lower hinge (left) (9). (Fig. E)
6. The door revolves 180 degrees, install the door with same way it was removed
and fix it with door aligned.
7. Block the hole at right top of cabinet with spare decorative plugs (8).
Please keep this instruction manual for future reference
7
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 13
13
24/10/2016 10:05
INSTALLING THE BAR HANDLE
Remove
the door gasket on the drilling holes side to install the handle. Once the
lling the bar
handle
been
removed,
handle
place.
(see
below
drawing).
ve the door gasket
gasket has
on the
drilling
holes screw
side tothe
install
the into
handle.
Once
the
gasket
een removed, screw the handle into place. (see below drawing)
Front
Back
the handle isOnce
fixed,
replace
the
by pushing
back into
the
handle
is gasket
fixed, replace
the gasket
by place.
pushing back into place.
ng a kitchen plinth
model is recessed to fit a kitchen plinth. A H75mm vent slot is required in the plinth to ensure
able to ventilate correctly. See diagram below. Failure to include this vent slot will invalidate the
ntee. The appliance comes included with a decorative plinth grille which slots onto the kitchen
.
RUN
DOWN
DISPLAY
Please keep this instruction manual for future reference
14
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 14
24/10/2016 10:05
FITTING A KITCHEN PLINTH
Once the handle is fixed, replace the gasket by pushing back into place.
This model is recessed to fit a kitchen plinth. A H75mm vent slot is required in
the plinth to ensure air is able to ventilate correctly. See diagram below. Failure to
Fitting a kitchen
plinth
include this
vent slot will invalidate the guarantee. The appliance comes included
This model iswith
recessed
to fit a kitchen
plinth.
A H75mm
ventthe
slotkitchen
is required
in the plinth to ensure
a decorative
plinth grille
which
slots onto
plinth.
air is able to ventilate correctly. See diagram below. Failure to include this vent slot will invalidate the
guarantee. The appliance comes included with a decorative plinth grille which slots onto the kitchen
plinth.
RUN
DOWN
DISPLAY
8
Please keep this instruction manual for future reference
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 15
15
24/10/2016 10:05
WINE BOTTLE STACKING
Wi3121 Wi3122 Wi3122WH bottle stacking guide
Without humidity tank
With humidity tank
Full shelf
Half shelf
With humidity tank
www.caple.co.uk
Stores max. 19 Bordeaux style wine bottles 750ml.
Please note, if you wish to store other style bottles i.e champagne, the removal of
some shelves is recommended to be able to accommodate these.
Please keep this instruction manual for future reference
16
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 16
24/10/2016 10:05
Installation dimensions
min 825mm
INSTALLATION DIAGRAM
Installation dimensions
min 825mm
Fixing the top fixing bracket
Fixing the top fixing bracket
FIXING
THE TOP FIXING BRACKET
After installing th
open the door, ad
and fix this in pos
using a screwdriv
surface/kitchen ca
a)
b)
c)
d)
After installing the wine cabinet, please
open the door, adjust the fixing bracket (a)
and fix this in position with three screws (c)
using a screwdriver (d) into the work
surface/kitchen cabinet.
a)
b)
c)
d)
This bracket will k
and help prevent
Top fixing bracket
Kitchen Cabinet
Screw
Screwdriver
! secure
This bracket will keep the product
help prevent it moving when in use.
After installing the wine cabinet,andplease
open the door, adjust the fixing bracket (a)
and fix this in position with three screws (c) using a screwdriver (d) into the work
10
surface
(b).
!
a) Top fixing bracket
10
b) Work surface
c) Screw
d) Screwdriver
This bracket will keep the product secure and help prevent it moving when in use.
Please keep this instruction manual for future reference
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 17
Top fixing
Kitchen C
Screw
Screwdriv
17
24/10/2016 10:05
Using the foot sliders
USING THE FOOT SLIDERS
If you want to adjust the height over 820mm, please install the product using the foot sliders
provided. These are provided to help prevent the feet catching on the floor when sliding the appliance
into the
aperture.
Placetotheadjust
back foot
the location
marked
‘Back’ below
and install
the frontthe
foot product
in the
If you
want
thein height
over
820mm,
please
using
location marked ‘Front’. Once fitted to both sides of the wine cabinet the appliance can be gently
the
foot
sliders
provided.
These
are
provided
to
help
prevent
the
feet
catching
on
positioned into the aperture, taking care notUsing
to place
excess
the
foot pressure
sliders on the feet when locating the
the floor when sliding the appliance
the the
aperture.
Place
theplease
backinstall
foottheinproduct
the using the foot slid
cabinet.
If you want into
to adjust
height over
820mm,
provided.
Thesefront
are provided
prevent
the feetmarked
catching on‘Front’.
the floor when sliding the applia
location marked ‘Back’ below
and the
foottoinhelp
the
location
aperture.
Place the
foot in the location
‘Back’
below and the front foot in
Back
Once fitted to both sides of into
thethe
wine
cabinet
theback
appliance
can bemarked
gently
positioned
location marked ‘Front’. Once fitted to both sides of the wine cabinet the appliance can be ge
into the aperture, taking care
not tointo
place
excesstaking
pressure
positioned
the aperture,
care noton
to the
place feet
excesswhen
pressure on the feet when locating
cabinet.
locating the cabinet.
Back
Front
Front
!
!
Back
Front
Back
Front
Foot slider
11
Foot slider
Please keep this instruction manual for future reference
18
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 18
11
24/10/2016 10:05
CARE AND MAINTENANCE
Cleaning your wine cabinet
-- Turn off the power, unplug the appliance, and remove all items including shelves
and rack.
-- Wash the inside surfaces with a warm water and baking soda solution. The
solution should be about 2 tablespoons of baking soda to 2 pints of water.
-- Wash the shelves with a mild detergent solution.
-- Wring excess water out of the sponge or cloth when cleaning the area of the
controls, or any electrical parts.
-- Wash the outside cabinet with warm water and mild liquid detergent. Rinse well
and wipe dry with a clean soft cloth.
NOTE
Please take care when cleaning the plinth grille as this may contain sharp edges.
Power failure
-- Most power failures are corrected within a few hours and should not affect the
temperature of your appliance if you minimise the number of times the door is
opened. If the power is going to be off for a longer period of time, you need to
take the proper steps to protect your contents.
Holidays
-- Short holidays: Leave the wine cabinet operating during holidays of less than three
weeks.
-- Long holidays: If the appliance will not be used for several months, remove
all items and turn off the appliance. Clean and dry the interior thoroughly. To
prevent odour and mould growth, leave the door open slightly (blocking it open if
necessary).
Please keep this instruction manual for future reference
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 19
19
24/10/2016 10:05
Moving your wine cabinet
-- Remove all items.
-- Securely tape down all loose items (shelves) inside your appliance.
-- Wind the adjustable legs up to the base to avoid damage.
-- Tape the door shut.
-- Be sure the appliance stays secure in the upright position during transportation.
Also protect outside of appliance with a blanket, or similar item.
Energy saving tips
-- The wine cabinet should be located in the coolest area of the room, away from
heat producing appliances, and out of the direct sunlight.
Please keep this instruction manual for future reference
20
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 20
24/10/2016 10:05
PROBLEMS WITH YOUR WINE CABINET
You can solve many common wine cabinet problems easily, saving you the cost of a
possible service call. Try the suggestions below to see if you can solve the problem
before calling Caple Service.
TROUBLESHOOTING GUIDE
Problem
Possible Cause
The wine cabinet
does not operate
Not plugged in.
The appliance is turned off.
The circuit breaker tripped or a blown fuse.
The wine cabinet is
not cold enough
Check the temperature control setting.
External environment may require a higher setting.
The door is opened too often.
The door is not closed completely.
The door gasket does not seal properly.
The compressor
turns on and off
frequently
The room temperature is hotter than normal.
A large amount of contents has been added to the wine cabinet.
The door is opened too often.
The door is not closed completely.
The temperature control is not set correctly.
The door gasket does not seal properly.
The light does not
work
The circuit breaker tripped or a blown fuse.
The bulb has burned out.
The light button is “OFF”.
Vibrations
Check that the appliance is level and installed on a flat,even surface.
The wine cabinet
seems to make too
much noise.
The rattling noise may come from the flow of the refrigerant, which is
normal.
As each cycle ends, you may hear gurgling sounds caused by the flow of
refrigerant in your wine cabinet.
Contraction and expansion of the inside walls may cause popping and
crackling noises, this is normal.
The wine cabinet is not level.
The door will not
close properly
The wine cabinet is not level.
The door was reversed and not correctly installed.
The gasket is dirty.
The shelves are out of position.
If the above table has not solved the problem please contact Caple Service by
phone on 0119 938 7420 or by email service@caple.co.uk
Please keep this instruction manual for future reference
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 21
21
24/10/2016 10:05
DEFROSTING/CONDENSATION
Your wine cabinet is designed with an “Auto-cycle” defrost system. When the RUN
cycle is OFF, the refrigerated surface of the wine cabinet (interior rear wall) defrosts
automatically. The defrosted water is channelled into a drain pan which is located at
the back of the cabinet next to the compressor from where it evaporates.
HUMIDITY SYSTEM
The wine cabinet is equipped with a system for maintaining the correct level of
humidity. If humidity is too low, insert the small plastic reservoir on to the top shelf.
Fill this reservoir 3/4 full with water. Check the water level occasionally and refill as
necessary.
Recommended storage temperatures
For storing ALL TYPES OF WINES
12˚C to 14˚C
Recommended drinking temperatures
Champagne NV, Sparkling
Champagne Vintage
Dry White Semillon, Sauvignon Blanc
Dry White Gewürztraminer, Riesling
Dry White Chardonnay
Vintage Chardonnay 1
Sweet White Sauternes Monbazillac, Late Harvest ice wine
Sweet whites vintage Sauternes
Beaujolais
Red Pinot Noir
Vintage Pinot Noir red
Red Cabernet, Merlot, French, Australian, New Zealand, Chilean,
Argentinean, Italian, Spanish, Californian
6˚C
10˚C
8˚C
10˚C
10˚C
4˚C
10˚C
14˚C
13˚C
16˚C
18˚C
Red Grenache, Syrah
16˚C
18˚C
Please keep this instruction manual for future reference
22
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 22
24/10/2016 10:05
TECHNICAL DATA
Model
Brand: CAPLE
Reference: Wi3122WH & Wi3122
Category of household refrigerating appliance :2
Supply
220-240V~ 50Hz
Dimension (WxDxH cm)
29.5 x 57.2 x 82 cm
Weight (kg)
29kg
Energy efficiency class
B
Annual Energy
Consumption (AEC)
190 kWh of energy per annum calculated on the basis of the
result obtained for 24h in standard test consumption. The
actual energy consumption will depend on use and the location
of the device.
Useful volume of the
compartments (l)
56L
Defrosting
Automatic defrost
Climate class
Climate class : N
This unit is designed to be used at an ambient temperature
between 16°C (the lowest temperature) and 32°C (the highest).
Acoustic emissions in the
air in dB (A) re 1 pW
43dB
Type installation
Free standing or/and built-in
Please keep this instruction manual for future reference
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 23
23
24/10/2016 10:05
Caple Service
Fourth Way
Avonmouth
Bristol
BS11 8DW
t: 0117 938 7420
e: service@caple.co.uk
www.caple.co.uk
Please keep this instruction manual for future reference
24
Instruction manual Wi3122 & Wi3122WH
Wi3122_Wi3122WH Wine Cabinet manual.indd 24
24/10/2016 10:05
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement