Caple Wi6141 Wine Cabinet Instruction Manual

Caple Wi6141 Wine Cabinet Instruction Manual
undercounter wine cabinet
instruction manual
WI6141
Contact Caple on 0117 938 7420 or for spare parts www.caple.co.uk
CONTENTS
Important safety instructions
2
Installation instructions
8
Before using your wine cabinet
8
Operating and setting the temperature
10
Control Panel
10
Using the shelves
12
How to change the door opening
13
Installing the bar handle
14
Fitting a kitchen plinth
15
Wine bottle stacking
16
Installation dimensions
17
Fixing the top fixing bracket
17
Using the foot sliders
18
Care and maintenance
19
Troubleshooting guide
21
Defrosting/condensation
22
The humidity system
22
Recommended storage temperatures
22
Recommended drinking temperatures
22
Technical data
23
Please keep this instruction manual for future reference
2
Instruction manual Wi6141
INTRODUCTION
Thank you for buying your new Caple Wine Cabinet.
To ensure that you get the best results from your new purchase, we strongly suggest
that you read this instruction manual thoroughly before use. This manual contains
installation advice, usage instructions and other important facts about your Caple
Wine Cabinet. If treated with care your Caple Wine Cabinet will give you many years
of trouble free use.
Please keep this instruction manual for future reference
Instruction manual Wi6141
3
WARNINGS
--To prevent damaging the door gasket, make sure the
door is fully open when pulling shelves out of the rail
compartment.
--The appliance must be positioned so that the plug is
accessible. Release the electric cord and move your
cabinet to its final location. Do not move your cabinet
while loaded with wine as you may distort the body.
--The wine cabinet should be installed in a suitable place
in order to avoid touching the compressor.
--After unpacking, make sure that the appliance is in
perfect order. If you have any doubt, do not use it and
contact your retailer.
--If the supply cord is damaged, it must be replaced by
a Caple service agent or a similarly qualified person in
order to avoid a hazard.
--This product is not designed for commercial use, it is a
household appliance only.
It is not intended to be used in:
•
•
•
Staff kitchen areas in shops, offices and other working
environments
Bed and breakfast type environments
By clients in hotels, motels and any other residential
type environments
Please keep this instruction manual for future reference
4
Instruction manual Wi6141
--This appliance is intended to be used exclusively for the
storage of wine.
IMPORTANT
Caple cannot be held liable for any non
compliance with these instructions.
ELECTRICAL SHOCK HAZARD
To reduce the risk of fire, electrical shock, or injury when using
your appliance, follow these basic precautions:
--Read all instructions before using the wine cabinet.
--DANGER or WARNING: Risk of child entrapment.
--Before you throw away your old wine cabinet: Take off
the door, leaving the shelves in place so that children
cannot easily climb inside.
--Never allow children to operate, play with, or crawl
inside the appliance.
--Never clean appliance parts with flammable fluids. The
fumes can create a fire hazard or explosion.
--Do not store or use gasoline or any other flammable
vapours and liquids in the vicinity of this or any other
appliance. The fumes can create a fire hazard or
explosion.
Please keep this instruction manual for future reference
Instruction manual Wi6141
5
--The refrigerant of this appliance is R600a, flammable
and explosive articles should not be put in or near the
cabinet, to avoid the risk of fire or explosion.
--This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance.
--Cleaning and user maintenance shall not be made by
children without supervision.
--When positioning the appliance, ensure the supply cord
is not trapped or damaged.
--Do not locate multiple portable socket-outlets or
portable power supplies at the rear of the appliance.
--Do not use plug adapter.
Symbol ISO 7010 W021
Warning; Risk of fire / flammable materials
Please keep this instruction manual for future reference
6
Instruction manual Wi6141
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household waste. Please
recycle where facilities exist. Check with your Local Authority or retailer for recycling
advice. This appliance is marked according to the European directive on Waste
Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product. The symbol
on the product indicates that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection point for the recycling of
electrical and electronic equipment. Disposal must be carried out in accordance with
local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this
product, please contact your local council, your household waste disposal service or
the retailer where you purchased the product
CE DECLARATIONS OF CONFORMITY
This appliance has been manufactured to the strictest standards and complies
with all applicable legislation, Low Voltage Directive (LVD) and Electromagnetic
Compatibility (EMC).
Please keep this instruction manual for future reference
Instruction manual Wi6141
7
INSTALLATION
Before using your wine cabinet
-- Remove the exterior and interior packing.
-- IMPORTANT: Before connecting the wine cabinet to the power source, let it stand
upright for at least 12 hours. This will reduce the possibility of a malfunction in the
cooling system from handling during transportation.
-- Clean the interior surface with lukewarm water using a soft cloth.
Before installation, turn the unit off and unplug it from the outlet.
NOTE
To protect the appliance in transit and delivery the door is packed tightly against the
cabinet. When first installed this can mean the door seal appears thinner on one
side of the door due to compression, this is normal and once out of the box it will
relax over a short period of time and the door will return to the normal position. If
you wish to speed up the process you can gently warm the seal with a hair dryer on
a low temperature setting. This can help relax the seal helping it return to normal
thickness a little faster.
INSTALLATION OF YOUR WINE CABINET
-- Place your wine cabinet on a floor that is strong enough to support it when it is
fully loaded.
-- To level your wine cabinet, adjust the front levelling leg at the bottom of the
cabinet.
-- Ensure it is perfectly level, as this will minimise any vibrations.
-- This appliance uses flammable refrigerant. Never damage the cooling pipework
during transportation.
-- Locate the wine cooler away from direct sunlight and sources of heat (ovens,
hobs, heaters, radiators, etc.). Never clean appliance parts with flammable fluids.
The fumes can create a fire hazard or explosion. When disposing your appliance,
please choose an authorized disposal site.
-- Avoid locating the unit in moist areas.
-- It is fitted with a power cord having an earth wire terminating in a 13amp plug.
-- Ensure the product is correctly ventilated (see page 15).
Please keep this instruction manual for future reference
8
Instruction manual Wi6141
-- Consult a qualified electrician or service engineer if the earthing instructions are
not completely understood.
-- Plug the wine cabinet into an exclusive, properly installed-grounded wall outlet.
Do not under any circumstances cut or remove the third (ground) pin from the
plug. Any questions concerning power and/or grounding should be directed
toward a certified electrician or Caple service.
WARNING: INCORRECT EARTHING CAN RESULT IN THE
RISK OF ELECTRIC SHOCK
Attention!
-- Store wine in sealed bottles
-- Do not overload the cabinet
-- Do not open the door unless necessary
-- Do not cover shelves with aluminium foil or any other shelf material which may
prevent air circulation
-- Should the wine cabinet be stored without use for long periods it is suggested,
after careful cleaning, to leave the door ajar to allow air to circulate inside the
cabinet in order to avoid possible formations of condensation, mould or odours.
-- Keep ventilation openings, in the appliance enclosure or in the built-in structure,
clear of obstruction;
-- Do not use mechanical devices or other means to accelerate the defrosting
process, other than those recommended by the manufacturer;
-- Do not damage the refrigerant circuit;
-- Do not use electrical appliances inside the storage compartments of the appliance,
unless they are the type recommended by the manufacturer
Please keep this instruction manual for future reference
Instruction manual Wi6141
9
OPERATING YOUR WINE CABINET
Please use the cabinet within ambient temperatures between 16-32ºC, if the
ambient temperature is higher or lower than this, it will cause the temperature to
fluctuate in the cabinet, possibly preventing it from reaching 5-18ºC.
SETTING THE TEMPERATURE
Set the desired cooling temperature by pressing the / keys. Each press of the
key will scroll through the available temperature settings in increments of 1°C.
The temperature setting can be adjusted from 5°C to 18°C
To view the actual temperature at anytime press and hold / for approximately
5 seconds, the actual temperature will temporarily flash in the LED display for 5
Seconds. After this it will revert back to the set temperature.
Flashing LED = Cabinet temperature
Steady LED = Set temperature
NOTE
If the unit is unplugged, power lost or turned off, you must wait 3 to 5 minutes
before restarting the unit. If you attempt to restart before this time delay, the wine
cabinet will not start.
When you use the wine cabinet for the first time or you restart the cabinet after
having been shut off for a long time, there could be a few degrees variance
between the temperature you select and the one indicated on the LED readout. This
is normal and it is due to the length of the activation time. Once the wine cabinet
has been running for a few hours everything will be back to normal.
Please keep this instruction manual for future reference
10
Instruction manual Wi6141
Control panel
•
•
CONTROL PANEL
Indicator
light illuminates to signify the cooling mode is currently in operation
“
”
Indicator light illuminates to signify the cooling mode is currently in operation.
TOUCH CONTROL KEYS
“
”Button
Used
to switch the internal light on/off
Used to switch the internal light on/off.
To switch the appliance on/off
(press
and hold this button for approximately 3 seconds)
” Button
“
To switch
thetoappliance
on/off (press
andincrements
hold this buttons for approximately 3 se
Used
raise the temperature
in 1ºC
tes to signify the cooling mode is currently in operation.
Temperature
Alarm
to lower the
temperature in 1ºC increments
• “
”Used
Button
If
inner
temperature
is
higher
than
is shown in the display panel, and the
Used to raise the temperature
in23°C,
1ºC“HI”
increments.
alarm sounds after one hour continuously. It warns you that the inner temperature is too
ernal light on/off.
high.
ALARM
tes
signify
the
mode
currently
operation.
If innercooling
temperature
is loweris
than
0°C, “LO” isin
shown
in the display panel, the
• to
“ TEMPERATURE
” Button
alarm sounds and the malfunction indicator lights at the same time.
Used
to lower
the temperature
by in
1ºC“HI”
increments.
If inner
temperature
is higher than
23°C,
is shown in the display panel,
s currently
in
in operation.
operation.
es currently
on/off
(press
andsounds
hold this
approximately
3 you
seconds).
and
the
alarm
afterbuttons
one hourfor
continuously.
It warns
that the inner
ernal
light
on/off.
temperature
is
too
high.
Setting the temperature
•
If inner temperature is lower than 0°C, “LO” is shown in the display panel, the
perature
in 1ºC
increments.
• Toalarm
set
the
temperature,
connect indicator
the power
cord
to asame
properly
sounds
thethis
malfunction
lights
at the
time. grounded outlet. In
e on/off
(press
andand
hold
buttons for approximately
3 seconds).
a power interruption, the previous temperature setting is automatically erased and
to afor
preset temperature3setting
of 12°C
uttons
uttons
forbyapproximately
approximately
3 seconds).
seconds).
perature
in 1ºC increments.
perature in 1ºC increments.
• Set the desired cooling temperature by pressing the buttons adjacent to the “
ure indicators. Each press of the buttons will scroll through the available temperature s
increments of 1°C.
perature by in 1ºC increments.
re, connect the power cord to a properly grounded outlet. In the event of
• previous
The temperature
setting
can be
adjusted fromerased
5°C to and
18°Cit will default
the
temperature
setting
is automatically
ure
re setting of 12°C
• To view the actual temperature at anytime press and hold the temperature adjustm
re,
the power
cord tothe
a properly
grounded
ng connect
temperature
by
buttons
adjacent
tooutlet.
thetemperature
“ In the /event
" temporarily fla
(up
or down)
for pressing
approximately
5 seconds,
the actual
willof
the
previous
temperature
setting
is
automatically
erased
and
it
will
default
s of LED
the buttons
will
through
thethis
available
temperature
in
display
for 5scroll
Seconds.
After
it will revert
back to settings
the set temperature.
a
outlet.
the
re
setting
ofgrounded
12°C
a properly
properly
grounded
outlet. In
In
the event
event of
of
Flashing
LED
=
Cabinet
temperature
ng
automatically
erased
and
Please keep this instruction manual for future reference
ng is
isSteady
automatically
erased
and itit will
will default
default
LED = Set
temperature
ng can
temperature
by pressing
buttons adjacent to the “
/
"
ing
be adjusted
from 5°C the
to 18°C
11
Instruction manual Wi6141
s of the buttons will scroll through the available temperature settings in
e
//
""
e buttons
buttons adjacent
adjacent to
to the
the ““
Internal light
In order to reduce energy consumption, the LED light within this wine cabinet will
automatically switch off after 10 minutes. If you would prefer the LED light to
for 5 seconds, the
remain on continuously, this is possible. Please press and hold
display will show “LP”. After 4 seconds the display will revert back to normal and
the light will remain on until manually switched off.
If you would like to revert back and conserve energy (recommended), press and
hold
for 5 seconds, the display will show “LF”. After 4 seconds the display will
revert back to normal, and the light will automatically switch off after 10 minutes.
USING THE SHELVES
Temperature Alarm
To prevent damaging the door gasket, make sure
to have the door opened fully
If inner temperature is higher than 23°C, “HI” is shown in the display panel, and th
alarm sounds after one hour continuously. It warns you that the inner temperature is
when pulling shelves out of the rail compartment.
high.
If inner temperature is lower than 0°C, “LO” is shown in the display panel, the
alarm sounds and the malfunction indicator lights at the same time.
For easy access to the storage content, you must pull the shelves approximately 1/3
out of the rail compartment, however this unit was designed with a notch on each
erature Alarm
sides of the shelf tracks to prevent bottles from falling.
mperature is higher than 23°C, “HI” is shown in the display panel, and the
unds after one hour continuously. It warns you that the inner temperature is too
Removing or installing shelves
mperature is lower than 0°C, “LO” is shown in the display panel, the
unds and the malfunction indicator lights at the same time.
To install or remove a shelf, tilt the shelf as per the diagram and simply pull out, or
push in the shelf until it sits on the support brackets securely.
Visit our Caple website to view a ‘How to video’ on this. www.caple.co.uk
Please keep this instruction manual for future reference
12
Instruction manual Wi6141
How to change the door opening
This appliance has reversible doors but is delivered with a right hinged door. The left hand
hinge kit comes with the unit (in the box), should you wish to reverse the hinge on your unit
follow the directions below:
HOW TO CHANGE THE DOOR OPENING
1. Lower
hinge (Right)
. Screwsbut is delivered with
3 .Door
axishinged door. The
This
appliance
has reversible2 doors
a right
4. Door
5. Top
hinge
(Right)
6. Hingeyou
Screws
left
hand hinge kit comes with
the
unit
(in the box), should
wish to reverse the
7. Top hinge (Left)
8. Decorative plugs
9. Lower hinge (Left)
hinge
on your unit follow the
directions below:
10. Door limit device
11. Screw
12. Plug
1. Lower hinge (Right)
4. Door
7. Top hinge (Left)
10. Door limit device
2 . Screws
5. Top hinge (Right)
8. Decorative plugs
11. Screw
3 .Door axis
6. Hinge Screws
9. Lower hinge (Left)
12. Plug
1. Open the door to 90 degrees, take out 2 screws (2) from lower door axis (3), remove the door (4),
1.then
Open
door
toand
90 door
degrees,
take
pullthe
out the
door
axis (Fig.
A).out 2 screws (2) from lower door axis (3),
2. Put
the door
safely
take
outout
the the
plugdoor
(12) from
of door
unscrew 1 screw
remove
thedown
door
(4), and
then
pull
andtop
door
axis frame,
(Fig. A).
(11) at bottom and remove the door limit device (10), then install the door limit device (10) at top
2.ofPut
the
door
down
taketoout
the
top
of door
frame,
door
frame,
please
usesafely
spare and
plug (12)
block
theplug
hole (12)
at topfrom
of door
frame.
(Fig. A/B)
3. Take
out 3 hinge
screws
(6)at
from
top hinge
(5) and
(Fig.device
C)
unscrew
1 screw
(11)
bottom
and(right)
remove
theremove
door it.
limit
(10), then
4. Remove decorative nail (8) from left top of cabinet and install spare top hinge (Left) (7) at left top
install the door limit device (10) at top of door frame, please use spare plug (12)
of cabinet with 3 screws. (Fig. D)
to blockabove
the hole
at topinstall
of door
(Fig. (left)
A/B)(9). (Fig. E)
5. According
procedure,
spareframe.
lower hinge
6. The door revolves 180 degrees, install the door with same way it was removed and fix it with door
3.aligned.
Take out 3 hinge screws (6) from top hinge (right) (5) and remove it. (Fig. C)
7. Block the hole at right top of cabinet with spare decorative plugs (8).
4. Remove decorative nail (8) from left top of cabinet and install spare top hinge
(Left) (7) at left top of cabinet with 3 screws. (Fig. D)
5. According above procedure, install spare lower hinge (left) (9). (Fig. E)
6. The door revolves 180 degrees, install the door with same way it was removed
and fix it with door aligned.
7. Block the hole at right top of cabinet with spare decorative plugs (8).
Please keep this instruction manual for future reference
7
Instruction manual Wi6141
13
INSTALLING THE BAR HANDLE
Remove the door gasket on the drilled holes side by pulling from the top corner.
(see below drawing). Fix the handle to the screws and push the gasket back
into place.
Visit our caple website to view a ‘How to video’ at www.caple.co.uk.
Please keep this instruction manual for future reference
14
Instruction manual Wi6141
FITTING A KITCHEN PLINTH
Once the handle is fixed, replace the gasket by pushing back into place.
This model is recessed to fit a kitchen plinth. A H55mm vent slot is required in
Fitting
a kitchen
plinth
the plinth
to ensure
air is able to ventilate correctly. See diagram below. Failure to
This
model
is
recessed
to fitwill
a kitchen
plinth.
A H55mm
vent The
slot isappliance
required incomes
the plinth
to ensure
include this vent slot
invalidate
the
guarantee.
included
See
diagram
below.
Failure
to
include
this
vent
slot
will
invalidate
the
airwith
is ablea to
ventilate
correctly.
decorative plinth grille which slots onto the kitchen plinth.
guarantee. The appliance comes included with a decorative plinth grille which slots onto the kitchen
plinth.
Please keep this instruction manual for future reference
Instruction manual Wi6141
15
WINE BOTTLE STACKING
Stores max. 52 Bordeaux style wine bottles 750ml.
Please note, if you wish to store other style bottles i.e champagne, the removal of
some shelves is recommended to be able to accommodate these.
Instruction manual Wi6140
Please keep this instruction manual for future reference
16
Instruction manual Wi6141
INSTALLATION DIMENSIONS
INSTALLATION DIAGRAM
60
0m
min 825mm
m
m
3m
57
m
3m
58 r
min c doo
in
820-885mm
716mm
59
5m
m
FIXING THE TOP FIXING BRACKET
Fixing the top fixing bracket
After installing the wine cabinet, please
open the door, adjust the fixing bracket (a)
and fix this in position with three screws (c)
using a screwdriver (d) into the work
please
open cabinet.
the door, adjust the
surface/kitchen
After installing the wine cabinet,
fixing bracket (a)
and fix this in position with three screws
(c)
using
a
screwdriver
(d)
into the work
a) Top fixing bracket
16 surface
Instruction
b) Kitchen Cabinet
(b). manual Wi3121
c) Screw
Please keep this instruction manual for future reference
a kitchen plinth
d) Fitting
Screwdriver
a) Top fixing bracket
This model is recessed to fit a kitchen plinth. A H55mm vent slot is required in the plinth to ensure
Seesecure
diagram below. Failure to include this vent slot will invalidate the
air is able
ventilate
This bracket
willtokeep
thecorrectly.
product
guarantee.
appliance when
comes included
and help
preventThe
it moving
in use.with a decorative plinth grille which slots onto the kitchen
plinth.
!
b) Work surface
c) Screw
d) Screwdriver
10
This bracket will keep the product secure and help prevent it moving when in use.
Please keep this instruction manual for future reference
7
Instruction manual Wi6141
17
(!a ccple
(!aUSING
ccpleTHE FOOT SLIDERS
USING THE FOOT SLIDERS
If you want to adjust the height over 820mm, please install the product using
USING
THE
FOOT
SLIDERS
you want
toThese
adjust the
over 820mm,
install
thefeet
product
using on
the foot slidersIf provided.
areheight
provided
to helpplease
prevent
the
catching
the foot sliders provided. These are provided to help prevent the feet catching on
thewant
floortowhen
sliding
theover
appliance
into
aperture.
Place
the back foot in the
If you
adjust
height
820mm,
pleasethe
install
the aperture.
product
using
thethe
floor
when
sliding
the appliance
into the
Place the back foot in the
thelocation
foot sliders
provided.
These
are
provided
to
help
prevent
the
feet
catching
on
marked
‘Back’
below
and
the
front
foot
in
the
location
marked
location marked 'Back' below and the front foot in the location
marked ‘Front’.
'Front'.
theOnce
floor when
thefitted
appliance
into
theofaperture.
back
footcan
in can
the
fittedsliding
to Once
both
sides
the
wine
cabinet
thethe
appliance
bebegently
toof
both
sides
the
winePlace
cabinet
the
appliance
gently positioned
positioned
location marked 'Back'
and thetaking
front care
footnot
in the
location
marked
'Front'.
into below
the
aperture,
toexcess
place
excess
pressure
feetwhen
when
into the aperture,
taking
care not
to
place
pressure
on on
thethefeet
Once fitted to bothlocating
sides of the
thecabinet.
wine cabinet the appliance can be gently positioned
locating
the cabinet.
into
the aperture,
taking care not to place excess pressure on the feet when
locating the cabinet.
Front
Back
Front
Back
Foot slider
Foot slider
Please keep this instruction manual for future reference
18
Instruction manual Wi3123
Please keep this instruction manual for future reference
18
Wi3121 v.1ne cabinet.indd 18
Please keep this instruction manual for future reference
18
06/12/2016 10:551
Instruction
Wi3123
Wi3121manual
v.1ne cabinet.indd
18
Instruction manual Wi6141
06/12/2016 10:551
CARE AND MAINTENANCE
Cleaning your wine cabinet
-- Turn off the power, unplug the appliance, and remove all items including shelves
and rack.
-- Wash the inside surfaces with a warm water and baking soda solution. The
solution should be about 2 tablespoons of baking soda to 2 pints of water.
-- Wash the shelves with a mild detergent solution.
-- Wring excess water out of the sponge or cloth when cleaning the area of the
controls, or any electrical parts.
-- Wash the outside cabinet with warm water and mild liquid detergent. Rinse well
and wipe dry with a clean soft cloth.
NOTE
Please take care when cleaning the plinth grille as this may contain sharp edges.
Power failure
-- Most power failures are corrected within a few hours and should not affect the
temperature of your appliance if you minimise the number of times the door is
opened. If the power is going to be off for a longer period of time, you need to
take the proper steps to protect your contents.
Holiday
-- Short holidays: Leave the wine cabinet operating during holidays of less than three
weeks.
-- Long holidays: If the appliance will not be used for several months, remove
all items and turn off the appliance. Clean and dry the interior thoroughly. To
prevent odour and mould growth, leave the door open slightly (blocking it open if
necessary).
Please keep this instruction manual for future reference
Instruction manual Wi6141
19
Moving your wine cabinet
-- Remove all items.
-- Securely tape down all loose items (shelves) inside your appliance.
-- Wind the adjustable legs up to the base to avoid damage.
-- Tape the door shut.
-- Be sure the appliance stays secure in the upright position during transportation.
Also protect outside of appliance with a blanket, or similar item.
Energy saving tips
-- The wine cabinet should be located in the coolest area of the room, away from
heat producing appliances, and out of the direct sunlight.
Please keep this instruction manual for future reference
20
Instruction manual Wi6141
PROBLEMS WITH YOUR WINE CABINET
You can solve many common wine cabinet problems easily, saving you the cost of a
possible service call. Try the suggestions below to see if you can solve the problem
before calling Caple Service.
TROUBLESHOOTING GUIDE
Problem
Possible Cause
The wine cabinet
does not operate
Not plugged in.
The appliance is turned off.
The circuit breaker tripped or a blown fuse.
The wine cabinet is
not cold enough
Check the temperature control setting.
External environment may require a higher setting.
The door is opened too often.
The door is not closed completely.
The door gasket does not seal properly.
The compressor
turns on and off
frequently
The room temperature is hotter than normal.
A large amount of contents has been added to the wine cabinet.
The door is opened too often.
The door is not closed completely.
The temperature control is not set correctly.
The door gasket does not seal properly.
The light does not
work
The circuit breaker tripped or a blown fuse.
The bulb has burned out.
The light button is “OFF”.
Vibrations
check that the appliance is level and installed on a flat, even surface
The wine cabinet
seems to make too
much noise.
The rattling noise may come from the flow of the refrigerant, which is
normal.
As each cycle ends, you may hear gurgling sounds caused by the flow of
refrigerant in your wine cabinet.
Contraction and expansion of the inside walls may cause popping and
crackling noises, this is normal.
The wine cabinet is not level.
The door will not
close properly
The wine cabinet is not level.
The door was reversed and not correctly installed.
The gasket is dirty.
The shelves are out of position.
If the above table has not solved the problem please contact Caple Service by
phone on 0117 938 7420 or by email service@caple.co.uk
Please keep this instruction manual for future reference
Instruction manual Wi6141
21
DEFROSTING/CONDENSATION
Your wine cabinet is designed with an “Auto-cycle” defrost system. When the RUN
cycle is OFF, the refrigerated surface of the wine cabinet (interior rear wall) defrosts
automatically. The defrosted water is channelled into a drain pan which is located at
the back of the cabinet next to the compressor from where it evaporates.
HUMIDITY SYSTEM
The wine cabinet is equipped with a system for maintaining the correct level of
humidity. If humidity is too low, insert the small plastic reservoir on to the top shelf.
Fill this reservoir 3/4 full with water. Check the water level occasionally and refill as
necessary.
Recommended storage temperatures
For storing ALL TYPES OF WINES
12˚C to 14˚C
Recommended drinking temperatures
Champagne NV, Sparkling
Champagne Vintage
Dry White Semillon, Sauvignon Blanc
Dry White Gewürztraminer, Riesling
Dry White Chardonnay
Vintage Chardonnay 1
Sweet White Sauternes Monbazillac, Late Harvest ice wine
Sweet whites vintage Sauternes
Beaujolais
Red Pinot Noir
Vintage Pinot Noir red
Red Cabernet, Merlot, French, Australian, New Zealand, Chilean,
Argentinean, Italian, Spanish, Californian
6˚C
10˚C
8˚C
10˚C
10˚C
4˚C
10˚C
14˚C
13˚C
16˚C
18˚C
Red Grenache, Syrah
16˚C
Please keep this instruction manual for future reference
22
Instruction manual Wi6141
18˚C
TECHNICAL DATA
Model
Brand: CAPLE
Reference: Wi6141
Category of household refrigerating appliance :2
Supply
220-240V~ 50Hz
Dimension (WxDxH cm)
59.5 x 57.7 x 82 cm
Weight (kg)
48kg
Energy efficiency class
A
Annual Energy
Consumption (AEC)
145 kWh of energy per annum calculated on the basis of the
result obtained for 24h in standard test consumption. The
actual energy consumption will depend on use and the location
of the device.
Useful volume of the
compartments (l)
146L
Defrosting
Automatic defrost
Climate class
Climate class : N
This unit is designed to be used at an ambient temperature
between 16°C (the lowest temperature) and 32°C(the highest)
Acoustic emissions in the
air in dB (A) re 1 pW
43dB
Type installation
Free standing or/and built-in
Please keep this instruction manual for future reference
Instruction manual Wi6141
23
Caple Service
Fourth Way
Avonmouth
Bristol
BS11 8DW
t: 0117 938 7420
e: service@caple.co.uk
www.caple.co.uk
Please keep this instruction manual for future reference
24
Instruction manual Wi6141
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement