C4 Remote Control
SPECIFICATION and INSTRUCTION SHEET
DESCRIPTION: One Ceiling Fan & Light, 3 Speed Remote Control
ELECTRICAL SPECS: 120 Volts, 60 Hertz, Fan 1.0 amp, Light Rating 250W
Incandescent or Halogen, 5 Wire Installation
FAN MODELS USED: May be used in conjunction with C25 Wall Control
See Catalog or visit our website www.fanimation.com for more
information
How to Wire and Operate Your C4 Remote Control
NOTE: If fan or supply wires are different colors than indicated,
have this unit installed by a qualified electrician.
WARNING
Remote Transmitter
Unit Detail
Receiver Unit Detail
Figure 1a
Figure 1b
9V
Battery
To avoid possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advice, as it must be
grounded for safe operation.
WARNING
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not operate
fan until the blades is in place. Noise and fan damage
could result.
Ceiling
Bracket
(Open End)
Receiver Unit
NOTE: Receiver wires omitted for clarity.
Figure 2
GRN or BARE GROUND
WH-TO MOTOR N
BLK-TO MOTOR L
BLUE-FOR LIGHT DOWN
GRN from bracket
GRN from hanger ball
1. Setting the Code: The remote unit has 16 different code
combinations. It may be necessary to test a couple frequency
code settings to improve signal reception and/or eliminate
interference from other remote control household items. Multiple
fans should have different code settings to allow independent fan
control. To set the code, perform these steps.
• Transmitter: remove battery cover. Press firmly below arrow
and slide battery cover off. Slide code switches to your choice
of up or down position. Factory setting is all up. Do not use this
position. With a small screwdriver or ball point pen slide firmly up
or down (Figure 1a). Replace battery cover on the transmitter.
• Receiver: Slide code switches to the same positions as set
on your transmitter (Figure 1b).
2. Installing Receiver in Hanger Bracket:
• Slide remote Receiver into the Hanger Bracket (Figure 2).
• Connect wires as indicated: (Figure 3)
– Green Hanger Bracket and Hanger Ball wires to BARE
(ground) wire.
– BLACK Receiver Unit wire (AC IN L) to BLACK supply wire.
– WHITE Receiver Unit wire (AC IN N). to WHITE supply
wire.
– WHITE Receiver Unit wire (TO MOTOR N) to WHITE fan
wire.
– BLACK Receiver Unit wire (TO MOTOR L) to BLACK fan
wire.
– BLUE Receiver Unit wire (FOR LIGHT DOWN) to BLUE
light wire.
• Position all connected wires and receiver antenna to allow
installation of ceiling canopy.
• Using canopy screws threaded into the hanger bracket
reinstall ceiling canopy.
• Restore electrical power.
WH-AC IN N
BL-AC IN L
BLK-ANT
120 VAC SUPPLY
(User Supplied)
Figure 3
3. Operating & Using Remote Transmitter:
Install 9 volt battery (If not using for long periods of time, remove
battery to prevent damage to transmitter). Store the transmitter
away from excess heat or humidity.
• HI Push Button – high fan speed
• MED Push Button – medium fan speed
• LOW Push Button – low fan speed
• OFF Push Button – fan off
• Light Push Button – no function (unless light kit is installed)
NOTE: Set pull chain to high speed before using
the remote control. You can now use your speed
control to select any of the 3-speeds plus OFF.
10983 Bennett Parkway
Zionsville, IN 46077
(888) 567-2055 • FAX (866) 482-5215
Outside U.S. call (317) 733-4113
Visit Our Website @ www.fanimation.com
NOTE: To control light hold down key to increase
or decrease brightness. Tap key quickly to turn
light on or off. The light keys have auto resume
and will stay at the same brightness as the last
time it was turned off.
Copyright 2010 Fanimation
2010/02
">
