Bartscher 150718 Bar Blender Rio Operating instructions

Bartscher 150718 Bar Blender Rio Operating instructions | Manualzz




Rio Series Bar blender

Operation Manual (2)

Mélangeur de bar série Rio

Manuel d’utilisation (4)

Mezcladora para bar Rio

Manual de operación (6)

Liquidificador Série Rio

Manual do Utilizador (8)

Frullatore per bar Rio

Manuale per il funzionamento (10)

Standmixer der Rio Serie

Bedienungsanleitung (12)

Rio Serie Barmixer

Gebruiksaanwijzing (14)

Rio Series Bar–blender

Betjeningsvejledning (16)

Rio-serien barblandare

Bruksanvisning (18)

Serie Rio Hurtigmikser

Brukerhåndbok (20)







Liquidificador Série RIO

Manual de Instrucções (28)









2 GB


When using electrical appliances, basic safety precautions should be followed, including the following:

• • • • • • • • • •

Plug into a grounded outlet.

Do not remove ground.

Do not use an adapter.

Do not use an extension cord.

Disconnect power before cleaning or servicing.

To reduce risk of personal injury, unplug cord from outlet when not in use, and before putting on or taking off parts.

• • • •

Do not spray the base with a high-pressure spray gun.

Extreme caution must be used when moving an appliance containing hot oil or other hot liquids.

• •

Do not use appliance for other than intended use.

Not intended for use by or near children.

• Children should be supervised to ensure that they do not play with the appliance.

This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

To protect against electrical shock, do not immerse cord, plug, or blender base in water or any other liquid.

The use of accessory attachments not recommended by the appliance manufacturer may cause injuries.

Unplug the blender and inspect the power cord insulation for cracks on a weekly basis. Refer to “Technical Service” for repair or replacement. To reduce risk of personal injury and to prevent damage to blender or container and cutter assembly, DO NOT insert utensils into blender container while operating blender.

Do not store any kitchen utensils in the container because the blender would be damaged if inadvertently turned on.

Before first use, wash container assembly in hot, soapy water. Do NOT place in dishwasher.

To prevent possibility of serious personal injury, keep hands out of blender container while operating blender.

Always operate blender with container cover in place.

Read the Operation Manual before using blender. Keep Operation Manual handy.

Avoid contacting moving parts. Switch off the appliance and disconnect from power supply before changing accessories or approaching parts that move in use.

Blades are sharp. Handle carefully.

If cutter assembly blades are loose, discontinue use immediately and replace cutter assembly. Do not attempt to repair or tighten cutter assembly.

• • • • •

Inspect container and cutter assembly daily. Do not use broken, chipped, or cracked container. Check cutter for wear, nicks, or broken blades. Do not use broken, loose, or cracked cutting blades.

Do not use outdoors.

This appliance is intended for short periods of operation, with a rated operating time of 3 minutes.

Do not leave blender unattended while it is operating.

To prevent damage to blender, container, or cutter assembly, DO NOT move or shake blender while in operation. If blending action stops during operation, turn blender OFF (


), remove container from base, remove container cover, and use a thin rubber spatula to push mixture towards cutters.

When blending hot liquids, remove center-piece of two-piece lid. Hot liquids may push lid off jar during blending. To prevent possible burns: Do not fill blender jar beyond the 1 quart (1 liter) level. With the protection of an oven mitt or thick towel, place one hand on top of lid. Keep exposed skin away from lid. Start blending at lowest speed.

Always operate blender with container cover in place.

• • • •

This blender is designed with motor overload protection. If the motor stops during operation due to overheating, unplug the unit and allow it to cool down for 15 minutes. Plug unit back after 15 minutes to resume normal operation.

The normal function of this product may be disturbed by strong electromagnetic interference. If this occurs, simply reset the product and resume normal operation by following the operation manual. If normal operation cannot be resumed, place the product in a different location.

Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Refer to “Technical Service” for instructions on examination, repair, or electrical or mechanical adjustment.

If the supply cord of this appliance is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person.


If fitted with a non-rewirable U.K. plug, the 13 amp fuse approved by ASTA to be B.S. 1362 must be used. If you need a replacement fuse carrier, it must be replaced with the same colour coded carrier with the same markings. Fuse covers and carriers can be obtained from approved service agents.


Safety Alert Symbols The following safety alert symbols are used throughout this manual to alert you to the safety hazards described below.

Electrical Shock Hazard Disconnect power before cleaning blender base.

Failure to follow these instructions can result in death or electrical shock.

Electrical Shock Hazard Plug into a grounded outlet.

Do not remove ground.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Cut Hazard Always place cover on container when blending.

Do not put hands, spoons, or other utensils in container when blending.

Failure to follow these instructions can result in broken bones, cuts, or other injuries.

Burn Hazard Always use caution when blending hot contents.

Failure to follow these instructions can result in burns.


Sanitize using 1 tablespoon (15 ml) of household bleach per 1 gallon (3.8 liter) of clean, cool water (60°F/16°C), mixed according to the instructions on the bleach.


Fill container with sanitizing solution, replace cover and filler cap and run on LOW (1) speed for 2 minutes. Empty container.



Wipe exterior with soft cloth dampened with sanitizing solution.

Immerse cover and filler cap in sanitizing solution for 2 minutes.


Place empty container on base and run on HIGH (2) speed for 2 seconds to remove any moisture from the cutter assembly.

5. When ready to use

, rinse with clean water.

38 39

Technical Services

For assistance or replacement parts, call our Technical Services number:




Please do not dispose of any electrical equipment as ordinary waste. Help conserve natural resources and protect the environment: when you have finished using this product, please dispose of it at your local waste collection or recycling centre in the area reserved for electrical equipment. Contact your local authority to find the nearest waste collection centre. To remind you to dispose of this product responsibly and separately from ordinary waste, it is marked with the symbol of a crossed-out trash bin.


1 2 3


4 5 6

1 4 2 3 5 6 00:02 :00


Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Download PDF