Hirschmann Antennas of the BAT family Wireless LAN User Manual

Add to my manuals
72 Pages

advertisement

Hirschmann Antennas of the BAT family Wireless LAN User Manual | Manualzz

Antenna Guide Wireless LAN Antennas of the BAT family

WLAN Antenna Guide Release 12 09/2017 Technical Support https://hirschmann-support.belden.eu.com

The naming of copyrighted trademarks in this manual, even when not specially indicated, should not be taken to mean that these names may be considered as free in the sense of the trademark and tradename protection law and hence that they may be freely used by anyone.

© 2017 Hirschmann Automation and Control GmbH Manuals and software are protected by copyright. All rights reserved. The copying, reproduction, translation, conversion into any electronic medium or machine scannable form is not permitted, either in whole or in part. An exception is the preparation of a backup copy of the software for your own use.

The performance features described here are binding only if they have been expressly agreed when the contract was made. This document was produced by Hirschmann Automation and Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right to change the contents of this document without prior notice. Hirschmann can give no guarantee in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network components or the associated operating software. In addition, we refer to the conditions of use specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site (www.hirschmann.com).

Hirschmann Automation and Control GmbH Stuttgarter Str. 45-51 72654 Neckartenzlingen Germany WLAN Antenna Guide 11.10.2017

Contents

1

2

3

4 4.1

4.2

4.3

4.4

4.5

Introduction

Current BAT portfolio

Schematic representation for connecting

antennas and protectors to the devices

8

Antenna Selection Criteria 9

External antennas 15 Legal regulations for operation external antennas 4.1.1 Relevant for use in the USA and in Canada:FCC

compliant antennas

4.1.2 Relevant for use in Japan:

15

Omni-Directional Antennas 4.2.1 Omni-Directional Antenna for 2.4 GHz band

4.2.2 Omnidirectional antenna for 5 GHz band

4.2.3 Omnidirectional Antenna for 2.4 and 5 GHz band

4.2.4 Omni-directional dual-band antennae for MiMo for

the 2.4 GHz and 5 GHz bands

4.2.5 Dual band Hemispherical Antenna for 2.4 and 5 GHz

band

34

Sector Antennas 36 4.3.1 Polarization-diversity antenna for 2.4 GHz band, linear 36

4.3.2 Polarization-diversity antenna for 5 GHz band, linear 38

4.3.3 Sectoral MiMoantenna for 5 GHz band 40

42 Directional Antennas 4.4.1 Directional antenna for the 2.4 GHz band with 14 dBi

gain

4.4.2 Directional antenna for 5 GHz band with 18 dBi gain

4.4.3 Directional antenna for 5 GHz band with a gain of

23 dBi

Radiating Cable Antennas (Leaky Cable)

33

42

46

50

53

15

22

24 24

26

27

5

6

WLAN Antenna Guide BAT Release 12 09/2017 3

5

A

B

C

4.5.1 Leaky Cable for 2.4 GHz; black

Cables/Adapter

Explanation of passive

antennas in explosive hazard areas

Antenna diagrams

Index

53

57

64

65

69

4 WLAN Antenna Guide BAT Release 12 09/2017

Introduction

Since 2004, Hirschmann Automation and Control GmbH has provided a continually expanding product portfolio relating to WLAN. Our product portfolio comprises the following integral WLAN network elements:  active devices such as access points or clients  passive components such as cables, antennas, and overvoltage protectors With our product portfolio, we focus on a high industrial suitability. In order to improve our products, in particular with regard to vibration resistance, grounding behavior, impermeability and emission behavior, we have further developed our antenna portfolio.

You benefit from the following modifications of our antenna portfolio:  All antennas comply with the IP65 degree of protection for a high industrial suitability. The sole exception to this is the BAT-ANT-N-14G IP23 antenna.

 The emission behavior of the new antennas is more homogeneous, with improved transmit and receive power during operation.

 The new antennas, equipped with N sockets, allow you to connect the antennas easily and quickly with other cables and overvoltage protectors.

 The scope of delivery comprises a complete solution, with an antenna, 3.28 ft (1 m) cable and pigtail included. The complete solution allows you to immediately connect the antenna to the following devices: BAT-C, BAT-F, BAT-R, BAT300-Rail, BAT450-F, BAT867-R  You obtain every antenna with vibration resistant, weatherproof, and sturdy mounting material.

We continually improve our product portfolio and include WLAN technology innovations in our portfolio. As a result, our portfolio is subject to short term changes. Check regularly for updates of our portfolio by visiting the Hirschmann product pages (www.hirschmann.com).

WLAN Antenna Guide BAT Release 12 09/2017 5

1 Current BAT portfolio

Device

BAT-C BAT867-R BAT300 family BAT450-F OpenBAT family

Table 1:

Supported standards

IEEE 802.11a/b/g/h/n IEEE 802.11a/b/g/n/ac IEEE 802.11a/b/g/h/n IEEE 802.11a/b/g/h/n IEEE 802.11a/b/g/h/n

Current BAT portfolio

Maximum gross data rate

65 MBit/s 867 MBit/s (2x MIMO) 300 MBit/s (2x MIMO) 450 MBit/s (3x MIMO) 450 MBit/s (3x MIMO) 6 WLAN Antenna Guide BAT Release 12 09/2017

BAT-C BAT867-R BAT300 family BAT300-Rail BAT300 family BAT300-F

The devices are supplied with an IP67 aluminum housing. They are suitable for use in an industrial environment.

The devices are supplied in metal casings that can be mounted on DIN rails of automation technology.

The devices are supplied in metal enclosures for mounting on DIN rails in automation or vehicle applications.

The devices are supplied in IP65/67 metal housings. They are designed for field level applications or harsh industrial environments.

BAT450-F

Industrial WLAN Access Points with different interfaces for connections using WLAN, WWAN (Wireless Wide Area Network, for example LTE) and Ethernet.

OpenBAT family BAT-F BAT-R

The devices are supplied in a metal housing that can be fastened to DIN rails using automation technology. They provide impressive flexibility and high speeds.

Table 2: BAT-Family: Overview

For further information, see the "User Manual Installation" for the corresponding device.

2 Schematic representation for connecting antennas and protectors to the devices

Access Point Pigtail 1 × – 3 × Optional Protector Optional Cable 6.56. ft (2 m), 16.4 ft (5 m), 49.2 ft (15 m) Cable 3.28 ft (1 m) 1 × – 3 × 1 × – 3 × Linear antenna BAT-C / BAT300-F / BAT450-F / BAT-F Dual Slant antenna 1 × – 3 × 1 × – 3 × 1 × – 3 × BAT300-Rail / BAT-R / BAT867-R MiMo antenna

f-m f-m f-m m-f

The provided accessories listed in the antenna description provides you with the following options:  3.28 ft (1 m ) cable with N plugs at both ends: connection of the antenna with this cable  Pigtail, R-SMA plug to N socket: connection of the antenna to devices with R-SMA socket

Note:

The BAT Protector can be screwed onto the BAT-C / BAT300-F / BAT450-F / BAT-F directly, or be connected between two cables, as it is equipped with a plug and a socket.

8 WLAN Antenna Guide BAT Release 12 09/2017

3 Antenna Selection Criteria

 Take into account the national regulations that apply to the operation of antennas before considering any other criteria.

See “Legal regulations for operation external antennas” on page 15.

Note:

Hirschmann recommends that you perform an on-site inspection and an analysis to prepare for the installation of a WLAN.

Typical antenna ranges, based on the frequency range and the antenna type:  Frequency range: 2.4 GHz – Short range: up to 218 yards (200 m) with omnidirectional antennas.

– Medium range: up to 0.62 miles (1 km) with sector antennas.

– Long range: up to 3.11 miles (5 km) with directional antennas.

 Frequency range: 5 GHz – Short range: up to 328 yards (300 m) with omnidirectional antennas.

– Medium range: up to 1.86 miles (3 km) with sector antennas.

– Long range: up to 9.32 miles (15 km) with directional antennas.

The typical ranges provide orientation for the first-time antenna selection. The actual antenna range depends on several factors such as output power, line of sight, and interference.

In the following table you find antenna descriptions. Together with the above described typical ranges, the descriptions provide orientation for the first-time antenna selection.

WLAN Antenna Guide BAT Release 12 09/2017 9

Art.-No Antenna Product Image

943 981-022 BAT ANT-N 6G-IP65

Description

Omnidirectional antenna for 2.4 GHz band

BAT-C BAT867-R BAT300 family

+++ +

BAT300 Rail

+ +

BAT450-F BAT300-F non-LTE LTE

+ + 943 981-003 BAT ANT-N 5A-IP65 Omnidirectional antenna for 5 GHz band +++ + + + + + 942 110-001 BAT ANT-N 3AGN IP67 Omnidirectional antenna for 2.4 GHz band and 5 GHz band +++ + + 942 047-001 BAT ANT-N 3AGN-F Omnidirectional antenna for 2.4 GHz band and 5 GHz band +++ + + +

OpenBAT family BAT-R BAT-F

+ + + + + +

Table 3: +++ very good; ++ good; + possible; – cannot be used; nr = not relevant Whether an antenna is actually suitable depends on the application case.

Art.-No Antenna Product Image

942 046-001 BAT ANT RSMA 2AGN-R

Description

Omnidirectional antenna for 2.4 GHz band and 5 GHz band -

BAT-C BAT867-R BAT300 family

+

BAT300 Rail

+ -

BAT450-F BAT300-F non-LTE LTE

-

OpenBAT family BAT-R BAT-F

+ 943 981-004 BAT ANT-N 6ABG IP65 943 981-005 BAT ANT-N 14G-IP23 943 981-006 BAT ANT-N 18A-V IP65 943 981-007 BAT ANT-N 23A-V IP65

Table 3:

Hemispherical antenna for 2.4 GHz band and 5 GHz band Directional antenna for 2.4 GHz band with 14 dBi gain Directional antenna for 5 GHz band with 18 dBi gain Directional antenna for 5 GHz band with a high gain of 23 dBi +++ + + + + +

+++ very good; ++ good; + possible; – cannot be used; nr = not relevant Whether an antenna is actually suitable depends on the application case.

+ + + + + + + + + + + + + + + + + + + +

Art.-No Antenna Product Image

943 981-008 BAT ANT-N 23A-VH IP65 943 981-014 BAT ANT-N MiMo5 18N-IP65

Description

Directional antenna for 5 GHz band with a high gain of 23 dBi Directional antenna for 5 GHz band with 18 dBi gain -

BAT-C BAT867-R BAT300 family

-

BAT300 Rail

+++ +++

BAT450-F BAT300-F non-LTE LTE

+++ +++ +++ +++ +++ +++ ++ ++ 943 981-009 BAT ANT-N 8G-DS IP65 943 981-010 BAT ANT-N 9A-DS IP65 943 981-012 BAT ANT-N MiMoDB 5N-IP65 943 981-013 BAT ANT-N MiMo5 9N-IP65

Table 3:

Polarization diversity antenna for 2.4 GHz band, linear Polarization diversity antenna for 5 GHz band, linear Omni-directional dual-band antenna for MiMo for the 2.4 GHz and 5 GHz bands Sectoral MiMoantenna for 5 GHz band + ++ ++ +++

+++ very good; ++ good; + possible; – cannot be used; nr = not relevant Whether an antenna is actually suitable depends on the application case.

++ ++ +++ +++ ++ +++ +++ ++ +++ +++

OpenBAT family BAT-R BAT-F

+++ +++ +++ +++ ++ ++ ++ ++ +++ +++ +++ +++

Art.-No Antenna Product Image

943 981-001 BAT ANT-N LC-G 50m-IP65 943 981-101 BAT ANT-N LC-G 100m IP65 943 903-373 BAT ANT Protector m-f 943 903-374 BAT-LAN Protector IP68 943 903-360 BAT Pigtail 943 903-514 BAT-CLB 2 N m-f

Description BAT-C BAT867-R BAT300 family

+++

BAT300 Rail

+++ +++

BAT450-F BAT300-F non-LTE LTE

+++ +++ Leaky wave conductor for 2.4 GHz, black, 50m Leaky wave conductor for 2.4 GHz, black, 100m +++ +++ Overvoltage Protector +++ +++ +++ +++ +++ +++ +++ +++ +++ +++ +++ Surge Arrestor LAN/PoE Adapter cable (N socket/RP SMA plug) +++ nr Antenna Cable N-Plug to N-Jack 2 m (6.56 ft) +++ +++ +++ +++ +++ +++ +++ +++ +++ +++ +++ +++ +++

Table 3: +++ very good; ++ good; + possible; – cannot be used; nr = not relevant Whether an antenna is actually suitable depends on the application case.

OpenBAT family BAT-R BAT-F

+++ +++ +++ +++ +++ +++ +++ +++ +++ +++ +++

Art.-No Antenna Product Image

943 903-516 BAT-CLB 5 N m-f 943 903-515 BAT-CLB 15 N m-f

Description

Antenna Cable N-Plug to N-Jack 5 m (16.40 ft)

BAT-C BAT867-R BAT300 family

+++ +++

BAT300 Rail

+++

BAT450-F BAT300-F non-LTE LTE

+++ +++ +++ Antenna Cable N-Plug to N-Jack 15 m (49.21 ft) +++ +++ +++ +++ +++ +++

Table 3: +++ very good; ++ good; + possible; – cannot be used; nr = not relevant Whether an antenna is actually suitable depends on the application case.

OpenBAT family BAT-R BAT-F

+++ +++ +++ +++

4 External antennas

This chapter is structured as follows: 

“Legal regulations for operation external antennas” on page 15

“Omni-Directional Antennas” on page 24

  

“Sector Antennas” on page 36

“Directional Antennas” on page 42

“Radiating Cable Antennas (Leaky Cable)” on page 53

4.1

Legal regulations for operation external antennas

You find additional information on approvals, certifications, and self declarations in the Installation user manuals for the devices.

 Before operating the antennas, refer to the “Safety instructions” chapter in the “User Manual Installation” for your device or devices.

4.1.1

Relevant for use in the USA and in Canada: FCC compliant antennas  OpenBAT, BAT450-F For the operation of the OpenBAT and BAT450-F devices in the USA and in Canada (characteristic value US for country approval) you require a permit for the operation of antennas. If the operation of a specific antenna is legal depends on the frequency band and the WLAN module used. The following tables provide you an overview of the approved antennas.

WLAN Antenna Guide BAT Release 12 09/2017 15

Art.-No

942 046 001

Antennas operating with this device model:

BAT-ANT-RSMA-2AGN-R

Product Image Description

Omnidirectional antenna for 2.4 GHz band and 5 GHz band

Permitted band of operation 2.4 GHz band 5.15 GHz ... 5.25 GHz band

Yes Yes

5.725 GHz ... 5.825 GHz band

Yes 942 110 001 BAT-ANT-N-3AGN-IP67 Omnidirectional antenna for 2.4 GHz band and 5 GHz band Yes Yes Yes 943 981 012

Table 4:

BAT-ANT-N-MiMoDB-5N-IP65 Omni-directional dual-band antenna for MiMo for the 2.4 GHz and 5 GHz bands Yes Yes

This table applies exclusively to OpenBAT and BAT450-F devices that are labeled as follows: Contains Transmitter Module FCC ID: U99EWLAN1 IC: 4019A-EWLAN1

Yes

Art.-No

943 981 013

Antennas operating with this device model:

BAT-ANT-N-MiMo5-9N-IP65

Product Image Description

Sectoral MiMoantenna for 5 GHz band

Permitted band of operation 2.4 GHz band 5.15 GHz ... 5.25 GHz band

No Yes 943 981 009

Table 4:

BAT-ANT-N-8G-DS-IP65 Polarization diversity antenna for 2.4 GHz band, linear Yes No

This table applies exclusively to OpenBAT and BAT450-F devices that are labeled as follows: Contains Transmitter Module FCC ID: U99EWLAN1 IC: 4019A-EWLAN1

5.725 GHz ... 5.825 GHz band

Yes No The FCC approval is valid only in conjunction with the listed antennas. If other antennas are used, the approval expires. The responsibility lies with the operator of the system. The required antenna impedance is 50 Ω .

Art.-No

942 046-001

Antennas operating with this device model:

BAT-ANT-RSMA-2AGN-R

Product Image Description

Omnidirectional antenna for 2.4 GHz band and 5 GHz band

Permitted band of operation 2.4 GHz band 5.15 GHz ... 5.25 GHz band

Yes Yes

5.725 GHz ... 5.825 GHz band

Yes 942 110-001 BAT-ANT-N-3AGN-IP67 Omnidirectional antenna for 2.4 GHz band and 5 GHz band Yes Yes 943 981-012 943 981-013 BAT-ANT-N-MiMoDB-5N IP65 BAT-ANT-N-MiMo5-9N-IP65 Omni-directional dual-band antenna for MiMo for the 2.4 GHz and 5 GHz bands Sectoral MiMoantenna for 5 GHz band Yes No Yes Yes

Table 5: This table applies exclusively to OpenBAT and BAT450-F devices that are labeled as follows: Contains Transmitter Module FCC ID: U99EWLAN2 IC: 4019A-EWLAN2

Yes Yes Yes

Art.-No

943 981-009 943 981-014

Antennas operating with this device model:

BAT-ANT-N-8G-DS-IP65

Product Image

BAT-ANT-N-MiMo5-18N IP65

Description

Polarization diversity antenna for 2.4 GHz band, linear Directional antenna for 5 GHz band with 18 dBi gain

Permitted band of operation 2.4 GHz band

Yes

5.15 GHz ... 5.25 GHz band

No No No

5.725 GHz ... 5.825 GHz band

No Yes

Table 5: This table applies exclusively to OpenBAT and BAT450-F devices that are labeled as follows: Contains Transmitter Module FCC ID: U99EWLAN2 IC: 4019A-EWLAN2

The FCC approval is valid only in conjunction with the listed antennas. If other antennas are used, the approval expires. The responsibility lies with the operator of the system. The required antenna impedance is 50 Ω .

 BAT867-R For the operation of the BAT867-R devices in the USA and in Canada (characteristic value US for country approval) you require a permit for the operation of antennas. If the operation of a specific antenna is legal depends on the frequency band and the WLAN module used. The following table provides you an overview of the approved antennas.

20 WLAN Antenna Guide BAT Release 12 09/2017

Art.-No

942 046 001

Antennas operating with this device model:

BAT-ANT-RSMA-2AGN-R

Product Image Description

Omnidirectional antenna for 2.4 GHz band and 5 GHz band

Permitted band of operation 2.4 GHz band 5 GHz band

Yes

5180 ... 5240 MHz

Yes

5260 ... 5320 MHz

Yes

5500 ... 5720 MHz

Yes

5745 ... 5825 MHz

Yes 943 981 012

Table 6:

BAT-ANT-N-MiMoDB-5N IP65 Omni-directional dual-band antenna for MiMo for the 2.4 GHz and 5 GHz bands Yes Yes

This table applies exclusively to BAT867-R devices that are labeled as follows: Contains Transmitter Module FCC ID: TK4WLE600VX IC: 7849A-WLE600VX

Yes Yes Yes The FCC approval is valid only in conjunction with the listed antennas. If other antennas are used, the approval expires. The responsibility lies with the operator of the system. The required antenna impedance is 50 Ω .

4.1.2

Relevant for use in Japan: The following table applies to OpenBAT variants with the characteristic value JP (Japan) that are labeled as follows:  "Contains MIC ID: 204-310014" 

„5GHz band: この製品は屋内においてのみ使用可能です “

Art.-No

942 110 001

Antennas operating with this device model:

BAT-ANT-N 3AGN-IP67

Product Image Description

Omnidirectional antenna for 2.4 GHz band and 5 GHz band

Permitted band of operation 2.4 GHz band

Yes

5 GHz band

Yes 942 046 001 BAT-ANT RSMA-2AGN R Omnidirectional antenna for 2.4 GHz band and 5 GHz band Yes Yes 943 981 004 BAT-ANT-N 6ABG-IP65 943 981 012 BAT-ANT-N MiMoDB-5N IP65 943 981 009 BAT-ANT-N 8G-DS-IP65 943 981 010 BAT-ANT-N 9A-DS-IP65 943 981 022 BAT-ANT-N 6G-IP65 Hemispherical antenna for 2.4 GHz band and 5 GHz band Yes Omni-directional dual-band antenna for MiMo for the 2.4 GHz and 5 GHz bands Polarization diversity antenna for 2.4 GHz band, linear Yes Yes No Polarization diversity antenna for 5 GHz band, linear Omnidirectional antenna for 2.4 GHz band Yes Yes Yes No Yes No 22 WLAN Antenna Guide BAT Release 12 09/2017

Art.-No

943 981 003

Antennas operating with this device model:

BAT-ANT-N 5A-IP65

Product Image Description

Omnidirectional antenna for 5 GHz band

Permitted band of operation 2.4 GHz band 5 GHz band

No Yes 943 981 013 BAT-ANT-N MiMo5-9N IP65 Sectoral MiMo antenna for 5 GHz band No Yes Using antennas that are not on this list is prohibited. The 5 GHz band is restricted to indoor usage.

WLAN Antenna Guide BAT Release 12 09/2017 23

4.2

Omni-Directional Antennas

4.2.1

Omni-Directional Antenna for 2.4 GHz band  BAT-ANT-N-6G-IP65 Order number: 943 981-022 2 5 0 ± 5 1 2 2 6 5 1 5 1 5 2 x 3 . 5 4 5 1 5 1 5 24 WLAN Antenna Guide BAT Release 12 09/2017

Radiation Pattern horizontal 2400 MHz vertical 2400 MHz Frequency range Gain VSWR (voltage standing wave ratio) Polarization HPBW (half power bandwidth) 2400 MHz ... 2500 MHz 6.0 dBi < 1.8

Linear, vertical horizontal 360° Downtilt 0° Max. Power 25 W Impedance Connector 50 Ω N female

Table 7: Electrical Specification

Operating temperature Storage temperature Radome color Radome material − 40 ºF ... +185 ºF ( − 40 ºC ... +85 ºC) − 67 ºF ... +185 ºF ( − 55 °C ... +85 °C) RAL 9003 Fiber glass Dimensions Protection class Flammability

Table 8:

ø 0.87 in × 9.84 in (ø 22 mm × 250 mm) IP67 UL 94-HB

Environmental & Mechanical Characteristics

3.28 ft (1 m) with N plugs at both ends.

Pigtail, R-SMA male to N female Mounting material

Table 9: Cable and Accessories

WLAN Antenna Guide BAT Release 12 09/2017 25

4.2.2

Omnidirectional antenna for 5 GHz band  BAT-ANT-N-5A-IP65 Order Number: 943 981-003 Radiation Pattern horizontal 5470 MHz vertical 5470 MHz Frequency range Gain VSWR (voltage standing wave ratio) Polarization HPBW (half power bandwidth) HPBW (half power bandwidth) Max. Power Impedance Connector

Table 10: Electrical Specification

5150 MHz ... 5875 MHz 5 dBi 1.5

Linear, vertical horizontal 360° vertical 25° 6 W 50 Ω N female 26 WLAN Antenna Guide BAT Release 12 09/2017

Temperature Radome color − 49 °F ... +158 °F ( Grey-white Radome material Polypropylene (0.3 kg) − 45 °C ... +70 °C) Dimensions Protection class 0.63 in. × 6.30 in. (16 mm × 160 mm) IP65

Table 11: Environmental & Mechanical Characteristics

3.28 ft (1 m) with N plugs at both ends.

Pigtail, R-SMA male to N female Mounting material

Table 12: Cable and Accessories

4.2.3

Omnidirectional Antenna for 2.4 and 5 GHz band  BAT-ANT-N-3AGN-IP67 Order number: 942 110-001 (10 pcs.) Ø 12,9 Ø 0.50

mm inch Ø 12,9 Ø 0.50

Radiation Pattern horizontal 2.4 GHz WLAN Antenna Guide BAT Release 12 09/2017 horizontal 5 GHz Ø 20 Ø 0.79

27

10 0 -10 -20 150 180 -20 -10 0 10 210 vertical 2.4 GHz 120 240 -20 -10 0 10 10 0 -10 -20 150 180 210 120 240 90 270 90 60 30 H_Plane 2400 2450 2500 300 330 0 60 30 E_Plane 2400 2450 2500 300 330 0 10 0 -10 -20 150 180 -20 -10 0 10 210 vertical 5 GHz -20 -10 0 10 10 0 -10 -20 150 180 210 120 240 120 240 270 90 270 90 270 60 30 0 H_Plane 5150 5250 5350 5450 5550 5650 5750 5850 300 60 30 0 E_Plane 5150 5250 5350 5450 5550 5650 5750 5850 300 330 330 Frequency range Gain VSWR (voltage standing wave ratio) Polarization HPBW (half power bandwidth) HPBW (half power bandwidth) Max. Power Impedance Connector 2400 MHz ... 2485 MHz 5150 MHz ... 5850 MHz 2.0 dBi 2.0 dBi ≤ 2.0

Linear, vertical horizontal 360° vertical 30° 2.0 W 50 Ω N-type male

Table 13: Electrical Specification

vertical 15° Temperature Radome color Radome material − 40 °F ... +185 °F ( − 40 °C ... +85 °C) Black PC Dimensions Protection class 0.79 in. × 3.15 in. (20 mm × 80 mm) IP65 / IP67

Table 14: Environmental & Mechanical Characteristics

28 WLAN Antenna Guide BAT Release 12 09/2017

 BAT-ANT-N-3AGN-F Order Number: 942 047-001 (10 pcs.) The antenna is supplied with all BAT-F and BAT-C devices.

mm inch 22 0.87

The antenna is directly screwed on the BAT. Radiation Pattern horizontal 2400 MHz horizontal 5000 MHz WLAN Antenna Guide BAT Release 12 09/2017 29

vertical 2400 MHz vertical 5000 MHz Frequency range Gain VSWR (voltage standing wave ratio) Polarization HPBW (half power bandwidth) HPBW (half power bandwidth) Max. Power Impedance Connector 2400 MHz - 2500 MHz 2.5 dBi 2.0

Linear, vertical horizontal 360° vertical 30° 2.0 W 50 Ω N-type male

Table 15: Electrical Specification

5150 MHz ... 5875 MHz 5.0 dBi vertical 15° Temperature Radome color − 40 °F ... +158 °F ( Grey-white Radome material ABS (70 g) − 40 °C ... +70 °C) Dimensions Protection class 22 mm x 183 mm (0.87 in x 7.20 in) IP65

Table 16: Environmental & Mechanical Characteristics

30 WLAN Antenna Guide BAT Release 12 09/2017

 BAT-ANT-RSMA-2AGN-R Order Number: 942 046-001 (10 pcs.) 21,2 0.83

mm inch Radiation Pattern horizontal 2450 MHz 90° vertical 2450 MHz horizontal 5250 MHz WLAN Antenna Guide BAT Release 12 09/2017 vertical 5250 MHz 31

horizontal 5750 MHz vertical 5750 MHz Frequency range Gain VSWR (voltage standing wave ratio) Polarization HPBW (half power bandwidth) HPBW (half power bandwidth) Impedance Connector 2400 MHz 3 dBi 2.0

Linear, vertical horizontal 360° vertical 30° 50 Ω Reverse-SMA male

Table 17: Electrical Specification

5250 MHz and 5750 MHz 5 dBi vertical 15° Temperature Radome color − 4 °F ... +149 °F ( − 20 °C ... +65 °C) Black Radome material PC/PU (26 g) Dimensions 0.83 in × 6.3 in (21 mm × 160 mm)

Table 18: Environmental & Mechanical Characteristics

32 WLAN Antenna Guide BAT Release 12 09/2017

4.2.4

Omni-directional dual-band antennae for MiMo for the 2.4 GHz and 5 GHz bands  BAT-ANT-N-MiMoDB-5N-IP65 Order Number: 943 981-012 Radiation Pattern horizontal 2400 MHz 180 150 120 -150 -120 port 1 port 2 port 3 vertical 2400 MHz 180 150 120 -150 -120 port 1 port 2 port 3 90 -40 -30 -20 -10 0 -90 90 -40 -30 -20 -10 0 -90 60 30 0 horizontal 5470 MHz 120 150 180 -60 60 -30 -150 -120 port 1 port 2 port 3 30 vertical 5470 MHz 150 180 120 -30 -60 -150 -120 port 1 port 2 port 3 90 60 30 -40 -30 -20 -10 0 -90 -60 -30 0 90 60 30 -40 -30 -20 -10 0 -90 -60 -30 0 WLAN Antenna Guide BAT Release 12 09/2017 33

Frequency range Gain VSWR (voltage standing wave ratio) Polarization HPBW (half power bandwidth) Connector 2400 MHz ... 2500 MHz 5150 MHz ... 5875 MHz 3.5 dBi / 5.5 dBi 1.8

3 × Linear, vertical horizontal 360° Downtilt 0° Max. Power Impedance 50 Ω 3 × N male at 3.28 ft (1 m) cable directly attached

Table 19: Electrical Specification

Temperature Radome color − 40 °F ... +176 °F ( − 40 °C ... +80 °C) 7035 (Light Gray) Radome material plastic (0.3 kg) Dimensions Protection class 12.2 in × 4.33 in × 1.57 in (310 mm × 110 mm × 40 mm) IP65

Table 20: Environmental & Mechanical Characteristics

3 × 3 ft (90 cm) directly mounted to the antenna with N male connectors 3 × Pigtail, R-SMA male to N female Mounting material

Table 21: Cable and Accessories

4.2.5

Dual band Hemispherical Antenna for 2.4 and 5 GHz band  BAT-ANT-N-6ABG-IP65 Order Number: 943 981-004 Radiation Pattern horizontal 2400 MHz 34 vertical 2400 MHz WLAN Antenna Guide BAT Release 12 09/2017

horizontal 5470 MHz vertical 5470 MHz Ø 86 Ø 3.39

17,7 0.7

mm inch Ø 4,5 Ø 0.18

WLAN Antenna Guide BAT Release 12 09/2017 70 2.76

42,89 1.69

35

Frequency range Impedance VSWR (voltage standing wave ratio) Polarization Gain 3 dB beamwidth horizontal 3 dB beamwidth horizontal Max. Power

Table 22: Electrical Specification

3.28 ft (1 m) with N plugs at both ends.

Pigtail, R-SMA male to N female

Table 23: Cable and Accessories

2300 MHz ... 2500 MHz 4900 MHz ... 5935 MHz 50 Ω 1.8

Linear, vertical 6 dBi at 2.4 GHz 8 dBi at 5 GHz at 2.4 GHz 360° at 5 GHz 173° 75 W (CW) at 77 °F (25 °C)

4.3

Sector Antennas

4.3.1

Polarization-diversity antenna for 2.4 GHz band, linear  BAT-ANT-N-8G-DS-IP65 Order Number: 943 981-009 36 WLAN Antenna Guide BAT Release 12 09/2017

Radiation Pattern horizontal 2400 MHz vertical 2400 MHz

Table 24: Directional characteristic

Frequency range Impedance VSWR (voltage standing wave ratio) Polarization Isolation between ports Front to back ratio Max. Power Connector 2400 MHz ... 2485 MHz 50 Ω 1.5

dual linear, ± 45° slant Gain 3 dB beamwidth horizontal 8 dBi 75° 3 dB beamwidth vertical 70° Downtilt 0° 25 dB 14 dB 10 W (CW) at 77 °F (25 °C) 2 × N female

Table 25: Electrical Specification

Dimensions Radome material Radome color Operating temperature range Storage temperature range Windload Protection class

Table 26: Mechanical Properties

3.98 in × 3.15 in × 1.38 in (101 mm × 80 mm × 35 mm) LEXAN EXL 9330 RAL 7044 (silk gray) − 40 °F ... +176 °F ( − 40 °C ... +80 °C) − 40 °F ... +176 °F ( − 40 °C ... +80 °C) 3.37 lbf at 99 m/h (15 N at 160 km/h) IP65 WLAN Antenna Guide BAT Release 12 09/2017 37

2 × 3.28 ft (1 m) with N male connectors at both ends 2 × Pigtail, R-SMA male to N female Mounting material

Table 27: Cable and Accessories

4.3.2

Polarization-diversity antenna for 5 GHz band, linear  BAT-ANT-N-9A-DS-IP65 Order Number: 943 981-010 Radiation Pattern horizontal 5470 MHz vertical 5470 MHz 38 WLAN Antenna Guide BAT Release 12 09/2017

81 3.19

mm inch Frequency range Impedance VSWR (voltage standing wave ratio) Polarization Gain 3 dB beamwidth horizontal 3 dB beamwidth vertical 60° Downtilt 0° Isolation between ports Front to back ratio 20 dB 20 dB Max. Power Connector 5150 MHz ... 5925 MHz 50 Ω 2 dual linear, ± 45° slant 9 dBi 70° 10 W (CW) at 77 °F (25 °C) 2 × N female

Table 28: Electrical Specification

WLAN Antenna Guide BAT Release 12 09/2017 39

Dimensions Housing material Radome material Radome material Radome color Operating temperature range Storage temperature range Windload Protection class

Table 29: Mechanical Properties

3.98 in × 3.15 in × 1.38 in (101 mm × 80 mm × 35 mm) ASA and aluminum ASA LEXAN EXL 9330 RAL 7044 (silk gray) − 40 °F ... +176 °F ( − 40 °C ... +80 °C) − 40 °F ... +176 °F ( − 40 °C ... +80 °C) 3.37 lbf at 99 m/h (15 N at 160 km/h) IP65 2 × 3.28 ft (1 m) with N male connectors at both ends 2 × Pigtail, R-SMA male to N female Mounting material

Table 30: Cable and Accessories

4.3.3

Sectoral MiMoantenna for 5 GHz band  BAT-ANT-N-MiMo5-9N-IP65 Order Number: 943 981-013 Radiation Pattern horizontal – connection 1 vertical – connection 1 40 WLAN Antenna Guide BAT Release 12 09/2017

horizontal – connection 2 vertical – connection 2 horizontal – connection 3 vertical – connection 3 Frequency range Impedance VSWR (voltage standing wave ratio) Polarization

Table 31: Electrical Specification

WLAN Antenna Guide BAT Release 12 09/2017 5150 MHz ... 5875 MHz 50 Ω 1.5

3 × linear vertical / horizontal / +45° 41

Gain 3 dB beamwidth horizontal 3 dB beamwidth vertical 9 dBi 65° 65° Downtilt 0° Max. Power 2 W (CW) at 77 °F (25 °C) Connector N female

Table 31: Electrical Specification

Dimensions Radome material Radome color Operating temperature range Storage temperature range Windload Protection class

Table 32: Mechanical Properties

3.98 in × 3.15 in × 1.38 in (101 mm × 80 mm × 35 mm) LEXAN EXL 9330 RAL 7044 (silk gray) − 40 °F ... +176 °F ( − 40 °C ... +80 °C) − 40 °F ... +176 °F ( − 40 °C ... +80 °C) 3.37 lbf at 99 m/h (15 N at 160 km/h) IP65 3 × 3.28 ft (1 m) with N male connectors at both ends 3 × Pigtail, R-SMA male to N female Mounting material

Table 33: Cable and Accessories

4.4

Directional Antennas

4.4.1

Directional antenna for the 2.4 GHz band with 14 dBi gain  BAT-ANT-N-14G-IP23 Order Number: 943 981-005 42 WLAN Antenna Guide BAT Release 12 09/2017

Radiation Pattern horizontal 2400 MHz vertical 2400 MHz WLAN Antenna Guide BAT Release 12 09/2017 43

mm inch 40 1.57

252,99 9.96

200 7.87

Frequency range Impedance VSWR (voltage standing wave ratio) Polarization 2300 MHz ... 2500 MHz 50 Ω 1.5

vertical Gain 3 dB beamwidth horizontal 14 dBi 35° 3 dB beamwidth vertical 30° Downtilt 0° Front to back ratio Max. Power Connector 20 dB 75 W (CW) at 77 °F (25 °C) N female

Table 34: Electrical Specification

Dimensions Radome material Radome color Operating temperature range Storage temperature range Windload Protection class

Table 35: Mechanical Properties

3.98 in × 3.15 in × 1.38 in (101 mm × 80 mm × 35 mm) LEXAN EXL 9330 RAL 7044 (silk gray) − 40 °F ... +176 °F ( − 40 °C ... +80 °C) − 40 °F ... +176 °F ( − 40 °C ... +80 °C) 3.37 lbf at 99 m/h (15 N at 160 km/h) IP23 44 WLAN Antenna Guide BAT Release 12 09/2017

3.28 ft (1 m) with N plugs at both ends.

Pigtail, R-SMA male to N female Mounting material

Table 36: Cable and Accessories

Note:

Applies for use in the EU: If you use the antenna BAT-ANT-N-14G IP23 in combination with OpenBAT family devices, use the supplied 1 m (3.28ft) antenna cable in combination with BAT-CLB-2 N m-f cable.

WLAN Antenna Guide BAT Release 12 09/2017 45

4.4.2

Directional antenna for 5 GHz band with 18 dBi gain  BAT-ANT-N-18A-V-IP65 Order Number: 943 981-006 Due to their compact design, several of these antennas can be mounted on a single post. For better separation of the spatial streams with MiMo, you mount the antennas with different alignments (polarizations). Example: 1st antenna: vertical 2nd antenna: horizontal 3rd antenna: 45° horizontal Radiation Pattern horizontal 5470 MHz vertical 5470 MHz Frequency range Gain

Table 37: Electrical Specification

46 5150 MHz ... 5250 MHz 5250 MHz ... 5350 MHz 5350 MHz ... 5725 MHz 5725 MHz ... 5875 MHz 18 dBi 19 dBi 18.5 dBi 18 dBi WLAN Antenna Guide BAT Release 12 09/2017

Polarization HPBW / horizontal HPBW / vertical Front to back ratio Power handling Impedance Connector

Table 37: Electrical Specification

Linear, vertical 18° 18° > 30 dB 6 W (CW) 50 Ω N Jack Windload @ wind speed Temperature Radome material Radome color Weight Dimensions Protection class 23.4 lbf at 134 mi/h (104 N at 216 km/h) − 49 °F ... +158 °F ( − 45 °C ... +70 °C) plastic 7035 (Light Gray) 0.11 kg, 0.24 lb 7.48 in × 7.48 in × 1.2 in (190 mm × 190 mm × 30.5 mm) IP65 / IP67

Table 38: Environmental & Mechanical Characteristics

3.28 ft (1 m) with N plugs at both ends.

Pigtail, R-SMA male to N female Mounting material

Table 39: Cable and Accessories

 BAT-ANT-N-MiMo5-18N-IP65 Order Number: 943 981-014 MiMo is achieved via polarization diversity.

Relevant for North America:

See “Legal regulations for operation external antennas” on page 15.

WLAN Antenna Guide BAT Release 12 09/2017 47

305 12.0

66 2.60

+45° 14 0.55

mm inch 15,5 0.59

72,8 2.83

63,3 2.48

–45° Radiation Pattern 5 GHz horizontal - connection on the right (+45°)

Radiation Pattern

Amplitude [dB] Azimuth [deg] vertical - connection on the right (+45°)

Radiation Pattern

Amplitude [dB] Horizontal-Plane: Copolar horizontal - connection on the left (–45°) Elevation [deg] Vertical-Plane: Copolar vertical - connection on the left (–45°) 48 WLAN Antenna Guide BAT Release 12 09/2017

Amplitude [dB] Azimuth [deg]

Radiation Pattern

Amplitude [dB]

Radiation Pattern

Horizontal-Plane: Copolar horizontal - vertical connection

Radiation Pattern

Amplitude [dB] Azimuth [deg] Elevation [deg] Vertical-Plane: Copolar vertical - vertical connection Horizontal-Plane: Copolar

Radiation Pattern

Amplitude [dB] Horizontal-Plane: Copolar Elevation [deg] Vertical-Plane: Copolar

Band 1 Band 2 Band 3

Frequency range 4900 MHz ... 5150 MHz 5150 MHz ... 6000 MHz 6000 MHz ... 6100 MHz VSWR (voltage standing wave ratio) Gain HPBW / vertical 1.8

17 dBi 20° 1.8

18 dBi 1.8

16 dBi 15°

Table 40: Electrical Specification

Polarization Max. Power Impedance Connector

Table 41: General data

0°, +/ − 45° inclination 6 W 50 Ω N Jack WLAN Antenna Guide BAT Release 12 09/2017 49

Windload @ survival speed Temperature Radome material Radome color Weight Dimensions Protection class 263 N at 136 m/h (263 N at 220 km/h) − 49 °F ... +158 °F ( − 45 °C ... +70 °C) plastic Grey-white 3.31 lb (1.5 kg) 12.01 in × 12.01 in × 0.59 in (305 mm × 305 mm × 15 mm) IP67

Table 42: Environmental & Mechanical Characteristics

3 × 3.28 ft (1 m) with N male connectors at both ends 3 × Pigtail, R-SMA male to N female Mounting material for wall and mast mount

Table 43: Cable and Accessories

4.4.3

Directional antenna for 5 GHz band with a gain of 23 dBi  BAT-ANT-N-23A-V-IP65 Order Number: 943 981-007 50 Relevant for North America: Operate the antennas BAT-ANT-N-23A-V-IP65 and BAT-ANT-N-23A VH-IP65 exclusively in point-to-point connections.

Due to their compact design, several of these antennas can be mounted on a single post. For better separation of the spatial streams with MiMo, you mount the antennas with different alignments (polarizations). Example: 1st antenna: vertical 2nd antenna: horizontal 3rd antenna: 45° horizontal WLAN Antenna Guide BAT Release 12 09/2017

Radiation Pattern horizontal 5470 MHz vertical 5470 MHz Frequency range Gain VSWR (voltage standing wave ratio) Polarization HPBW / horizontal HPBW / vertical Front to back ratio Max. Power Impedance Connector

Table 44: Electrical Specification

3.28 ft (1 m) with N plugs at both ends.

Pigtail, R-SMA male to N female Mounting material for wall and mast mount

Table 46: Cable and Accessories

5150 MHz ... 5350 MHz 5470 MHz ... 5875 MHz 23 dBi < 1.5

Linear, vertical 9° 9° > 30 dB 6 W 50 Ω N Jack Windload @ wind speed Temperature Radome material Radome color 59.3 lbf at 136 m/h (264N at 220 km/h) − 49 °F ... +158 °F ( − 45 °C ... +70 °C) plastic Grey-white Dimensions Protection class 12.01 in × 12.01 in × 0.98 in (305 mm × 305 mm × 25 mm) IP65 / IP67

Table 45: Environmental & Mechanical Characteristics

WLAN Antenna Guide BAT Release 12 09/2017 51

 BAT-ANT-N-23A-VH-IP65 Order number: 943 981-008 Radiation Pattern Connection: horizontal / polarization: horizontal (5,470 MHz) Connection: horizontal / polarization: vertical (5,470 MHz) Connection: vertical / polarization: horizontal (5,470 MHz) Connection: vertical / polarization: vertical (5,470 MHz) 52 WLAN Antenna Guide BAT Release 12 09/2017

Frequency range Gain VSWR (voltage standing wave ratio) Polarization HPBW / horizontal HPBW / vertical Front to back ratio Max. Power Impedance Connector

Table 47: Electrical Specification

5150 MHz ... 5875 MHz 23 dBi < 1.7

dual Linear, vertical and horizontal 9° 9° − 30 dB 6 W 50 Ω 2 × N female Windload @ survival speed Temperature Radome material Radome color 59.3 lbf at 136 m/h (264N at 220 km/h) − 49 °F ... +158 °F ( − 45 °C ... +70 °C) plastic Grey-white Dimensions Protection class 14.61 in. × 14.61 in. × 1.57 in. (371 mm × 371 mm × 40 mm) IP65 / IP67

Table 48: Environmental & Mechanical Characteristics

2 × 3.28 ft (1 m) with N male connectors at both ends 2 × Pigtail, R-SMA male to N female Mounting material for wall and mast mount

Table 49: Cable and Accessories

4.5

Radiating Cable Antennas (Leaky Cable)

4.5.1

Leaky Cable for 2.4 GHz; black Radiating cables are coaxial cables that are equipped with small slots in their shields at regular intervals that operate as antennas. This leads to a homogeneous field around the cable.

100 m; 328 ft 50 m; 164 ft WLAN Antenna Guide BAT Release 12 09/2017 53

The 100 m (328 ft) cable is designed to be fed by 2 access points, each feeding the cable for approximately 50 m (164 ft). The 50 m (164 ft) cable is designed to be used with one Access Point and equipped with a terminator at the end.

 BAT-ANT-N-LC-G-50m-IP65 Order Number: 943 981-001 Cable length Cable specification

Table 50: Specification

Frequency band Antenna connector

Table 51: Radio technology

164 ft (50 m) 2 × N male connectors; 0.15 dB at 2.4 GHz 2000 MHz ... 2900 MHz N-type male Operating temperature Storage/transport temperature − 40 ºF ... +185 ºF ( − 40 ºC ... +85 ºC) − 70 ºC ... +85 ºC Dimensions 164 ft (50 m); d = 0.6 in (15 mm) Protection class IP65 (12 kg)

Table 52: Ambient conditions

Halogen free and flame retardant outer sheath Low corrosive gas emission according to IEC 60754-2 Flame retardant according to IEC 60332-1 and IEC 60332-3 cat. C Low smoke emission according to IEC 61034

Table 53: Flammability Characteristics

Leaky Cable 2 × N-connector, pre-assembled 1 × terminating resistor 50 Ohm 50 × fastening clip

Table 54: Scope of delivery and accessories

54 WLAN Antenna Guide BAT Release 12 09/2017

 BAT-ANT-N-LC-G-100m-IP65 Order Number: 943 981-101 Cable length Cable specification

Table 55: Specification

Frequency band Antenna connector

Table 56: Radio technology

Operating temperature Storage/transport temperature Dimensions Protection class

Table 57: Ambient conditions

100 m, 328 ft 2 × N male connectors; 0.15 dB at 2.4 GHz 2000 MHz ... 2900 MHz N-type male − 40 ºF ... +185 ºF ( − 40 ºC ... +85 ºC) − 70 ºC ... +85 ºC 328 ft (100 m); d = 0.6 in (15 mm) IP65 Halogen free and flame retardant outer sheath Low corrosive gas emission according to IEC 60754-2 Flame retardant according to IEC 60332-1 and IEC 60332-3 cat. C Low smoke emission according to IEC 61034

Table 58: Flammability Characteristics

Leaky Cable 2 × N-connector, preassembled 1 × terminating resistor 50 Ohm 100 × fastening clip

Table 59: Scope of delivery and accessories

Configurations Longitudinal Attenuation LC at 4 in (10 cm) from a concrete floor db/328 ft (dB/100 m) 15 LC at 0.6 in (15 mm) from a metal surface 17 LC directly against a metal surface 34

Table 60: Longitudinal attenuation of both cables between 2.4 and 2.485 GHz

WLAN Antenna Guide BAT Release 12 09/2017 55

Figure 1: Mounting a leaky wave conductor in the tunnel. Fastening clips are included in the delivery.

56 WLAN Antenna Guide BAT Release 12 09/2017

5 Cables/Adapter

All antennas are supplied with 1 m cable / N-plug to N-plug and pigtail.

 BAT-CLB-2 N m-m, BAT-CLB-2 N m-f Order Number: m-m: 943 903-513 m-f: 943 903-514 Length Diameter Attenuation Connector Protection class

Table 61: Characteristics

6.56 ft (2 m) 6 mm 1.4 dB / 2.4 GHz 3 dB / 5 GHz N male to female IP65 Temperature range Installation temperature range Flammability Halogen-free 2002/95/EC (RoHS) compliant

Table 62: Flammability Characteristics

− 40 ºF ... +185 ºF ( − 40 ºC ... +85 ºC) − 20 °C ... +60 °C UL 1581 § 1080 (VW-1) in compliance with IEC 60754 WLAN Antenna Guide BAT Release 12 09/2017 57

 BAT-CLB-5 N m-f Order Number: 943 903-516 Length Diameter Attenuation Connector

Table 63: Characteristics

16.4 ft (5 m) 13 mm 1.3 dB / 2.4 GHz 2.3 dB / 5 GHz N male/ N female Temperature range Installation temperature range Flammability Halogen-free 2002/95/EC (RoHS) compliant

Table 64: Flammability Characteristics

− 40 ºF ... +185 ºF ( − 40 ºC ... +85 ºC) − 20 °C ... +60 °C UL 1581 § 1080 (VW-1) in compliance with IEC 60754 58 WLAN Antenna Guide BAT Release 12 09/2017

 BAT-CLB-15 N m-f Order Number: 943 903-515 Length Diameter Attenuation Connector

Table 65: Characteristics

49.21 ft (15 m) 13 mm 3 dB / 2.4 GHz 4 dB / 5 GHz N male/ N female Temperature range Installation temperature range Flammability Halogen-free 2002/95/EC (RoHS) compliant

Table 66: Flammability Characteristics

− 40 ºF ... +185 ºF ( − 40 ºC ... +85 ºC) − 20 °C ... +60 °C UL 1581 § 1080 (VW-1) in compliance with IEC 60754 WLAN Antenna Guide BAT Release 12 09/2017 59

 BAT-Pigtail Order Number: 943 903-360 Length Diameter Attenuation Connector

Table 67: Characteristics

0.66 ft (0.2 m) 6 mm 0.5 dB / 2.4 GHz 1 dB / 5 GHz N female/ RPSMA-Plug 60 WLAN Antenna Guide BAT Release 12 09/2017

 BAT-ANT-Protector m-f Order Number: 943 903-373 The BAT-ANT-Protector m-f is a bandpass with electrical insulation. It helps prevent damage due to electrostatic discharging. The BAT-ANT-Protector m-f can enable a watertight connection to the switch cabinet.

This device is strongly recommended to be used in- and outdoor wherever electrical discharge, overvoltage or unclear grounding occur.

Please refer to the Outdoor Installation Guide for how to mount and plan the installation.

Main path connectors 1 2 Mounting and grounding Side of bulkhead Design specialty

Table 68: Product Configuration

Impedance Frequency range Return loss Insertion loss RF CW power Surge current handling capability Residual pulse energy

Table 69: Electrical Specification

Connection 1:

N socket, unprotected

Connection 2:

N plug, protected (electrically isolated) MH170/brk (MH=bulkhead mounting/brk=bracket) protected side inline design 50 Ω 2000 MHz ... 6000 MHz ≥ 20 dB ≤ 0.2 dB ≤ 300 W 50 multiple kA (test pulse 8/20 μ s) 0.0001 μ J typically (test pulse 4 kV 1.2/50 μ s / 2 kA 8/20 μ s) Main path - protected side WLAN Antenna Guide BAT Release 12 09/2017 61

Operating temperature Waterproof degree 2002/95/EC (RoHS) − 40 ºF ... +185 ºF ( − 40 ºC ... +85 ºC) IP65 (according to IEC 60529, data refers to the coupled state) compliant

Table 70: Environmental & Mechanical Characteristics

62 WLAN Antenna Guide BAT Release 12 09/2017

 BAT-LAN-Protector IP68 Order Number: 943 903-374 Overvoltage protector for the PoE/LAN cable.

Please refer to the Outdoor Installation Guide for how to mount and plan the installation.

Main path connectors RJ45 jack (female) – RJ45 jack (unprotected side – protected side) Grounding via mounting bracket or grounding M6 screw (ring of cable shoe > 0.26 in (6.5 mm))

Table 71: Product Configuration

Data transmission rate Frequency range Impedance Current rating Response Time Current handling capability Protection level Clamping voltage 1000 Mbit/s DC to 100 MHz 100 Ω per pair 2 ns wire - wire wire - ground shield – ground wire - wire wire - ground shield – ground wire - wire wire - ground shield – ground 1.5 A max.

0.1 kA (test pulse 8/20 µs) 2.5 kA (test pulse 8/20 µs) 6 kA (test pulse 8/20 µs) 20 V typically (test pulse 4 kV 1.2/50 μ s / 2 kA 8/20 µs) 700 V typically (test pulse 4 kV 1.2/50 μ s / 2 kA 8/20 µs) 700 V typically (test pulse 4 kV 1.2/50 μ s / 2 kA 8/20 µs) 15 V 90 V 90 V

Table 72: Electrical Specification

Cable category Operating temperature according to ISO/IEC 11801:2002 class D specified (up to CAT-5e system) − 40 ºF ... +185 ºF ( Protection class IP68 (0.33 kg) − 40 ºC ... +85 ºC)

Table 73: Environmental & Mechanical Characteristics

WLAN Antenna Guide BAT Release 12 09/2017 63

A Explanation of passive antennas in explosive hazard areas

Hirschmann BAT antennas are passive devices which are not able to increase the power by themselves. Devices which are specified in accordance with the ATEX directive complying with the technical standards EN 60079-0 and EN 60079-15 can be operated with all associated Hirschmann BAT antennas. You recognize the specified devices by their device label.

With the use of the prescribed device configuration, the 2 Watts maximum power permitted for the ATEX equipment group IIC is not reached in the following bands:  2.4 GHz ... 2.4835 GHz   5.15 GHz ... 5.35 GHz 5.47 GHz ... 5.725 GHz 64 WLAN Antenna Guide BAT Release 12 09/2017

B Antenna diagrams

This chapter was produced with the generous support of Huber+Suhner GmbH.

 Polarization and transmission The following section explains the vertical and horizontal polarization:  Vertical polarization With vertical polarization, the electrical field runs perpendicular to the earth’s surface. The magnetic field runs perpendicular to the electrical field in transmission direction ‘z’ - that is, parallel to the earth’s surface.

x z y

Figure 2: Electrical field in transmission direction ‘z’

 Horizontal polarization With horizontal polarization, the electrical field runs parallel to the earth’s surface. The magnetic field runs perpendicular to the electrical field in transmission direction ‘z’ - that is, perpendicular to the earth’s surface.

WLAN Antenna Guide BAT Release 12 09/2017 65

x z y h

Figure 3: Electrical field in transmission direction ‘z’

 Interpreting antenna diagrams The antenna diagrams used in this document show the directional characteristic of the relevant antenna in horizontal and vertical cross sections. When interpreting antenna diagrams, note the following:  Antenna diagrams only specify relative outputs.

  The relative output of the antenna depends on the observed angle.

The maximum output of an antenna is standardized to 0 dB in the antenna diagram.

Angles in the antenna diagram with 0 dB are known as main lobes.

  Angles in the antenna diagram with less than 0 dB are known as side lobes.

 The antenna diagram does not tell you anything about the absolute output of the antenna nor about the range of the antenna nor the antenna gain.

The following is an example of an interpretation of antenna diagrams: 66 WLAN Antenna Guide BAT Release 12 09/2017

Omni-directional antenna, horizontal cross-section, antenna viewed from above

in all angles ca. 0 dB

Omni-directional antenna, vertical cross-section, antenna viewed from the side

side lobe (~ -12 dB) side lobe (-10 dB) main lobe (0 dB) main lobe (0 dB) side lobe (~ -9 dB) side lobe (~ -11 dB)

Table 74: Interpreting antenna diagrams

 Decibels (dB) The remaining output of an antenna at a specific angle is shown in negative decibels (dB) on the antenna diagram.

See “Interpreting antenna diagrams” on page 67.

How do you interpret the negative decibel values on the antenna diagram?

Definition dB: Q (P) = 10 × lg 10 P 1 /P 2 dB The following table shows the attenuation in steps of − 3 dB:

Attenuation in decibels

− 3 − 6 − 9 − 12

Remaining output

1/2 1/4 1/8 1/16 In antenna diagrams, circles are used to display the attenuation – usually in steps of 10:

Attenuation in decibels

− 10 − 20 − 30 − 40

Remaining output

1/10 1/100 1/1000 1/10 000 Example: The above antenna diagram shows the output at − 30° as − 10 decibels.

WLAN Antenna Guide BAT Release 12 09/2017 67

See “Interpreting antenna diagrams” on page 67.

This means that the antenna transmits 1/10 of the maximum output at an angle of − 30°.

Example: The above antenna diagram shows the output at 150° as − 9 decibels.

See “Interpreting antenna diagrams” on page 67.

This means that the antenna transmits 1/8 of the maximum output at an angle of 150°.

68 WLAN Antenna Guide BAT Release 12 09/2017

C Index

A ATEX zone II F FAQ R Radiating cable T Technical questions Training courses

64

70

53

70 70

WLAN Antenna Guide BAT Release 12 09/2017 69

D Further support

Technical questions

For technical questions, please contact any Hirschmann dealer in your area or Hirschmann directly.

You find the addresses of our partners on the Internet at http://www.hirschmann.com

.

A list of local telephone numbers and email addresses for technical support directly from Hirschmann is available at https://hirschmann-support.belden.eu.com

.

This site also includes a free of charge knowledge base and a software download section.

Hirschmann Competence Center

The Hirschmann Competence Center is ahead of its competitors on three counts with its complete range of innovative services:    Consulting incorporates comprehensive technical advice, from system evaluation through network planning to project planning.

Training offers you an introduction to the basics, product briefing and user training with certification.

You find the training courses on technology and products currently available at http://www.hicomcenter.com

.

Support ranges from the first installation through the standby service to maintenance concepts.

With the Hirschmann Competence Center, you decided against making any compromises. Our client-customized package leaves you free to choose the service components you want to use.

Internet: http://www.hicomcenter.com

70 WLAN Antenna Guide BAT Release 12 09/2017

WLAN Antenna Guide BAT Release 12 09/2017 71

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement