Metra 95-3009 Radio Install kit Instructions

Add to my manuals
8 Pages

advertisement

Metra 95-3009 Radio Install kit Instructions | Manualzz

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) (1) #10 x 1/2” Phillips screw A B

Chevrolet

Camaro

1993-1996

KIT FEATURES

• ISO DDIN radio provision • Replacement trim panel is textured to match the factory finish

95-3009

I N S TA L L AT I O N I N S T R U C T I O N S

TABLE OF CONTENTS

Dash Disassembly ..................................................2

Kit Preparation .......................................................2

Kit Assembly ..........................................................3

WIRING & ANTENNA CONNECTIONS

(sold separately) Wiring Harness: 70-1858 Antenna Adapter: 40-GM10

Metra. The World’s Best Kits.

®

MetraOnline.com

C © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver • 9/32”, 10mm Socket wrench • Cutting tool

CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

REV. 1/4/18 INST95-3009

DASH DISASSEMBLY

1.

Remove (2) Phillips screws from the top of the driver’s side knee bolster.

2.

Remove (2) 9/32” screws from the bottom of the knee bolster.

3.

Open the glove box, remove (3) 9/32” screws exposed on the right edge of the radio trim bezel and remove the bezel. (Figure A)

4.

Remove (2) 9/32” screws securing the left side of the factory radio and (1) 10mm nut securing the right.

5.

Slide the radio from the dash and disconnect the wiring.

Continue to Kit Preparation (Figure A)

KIT PREPARATION

1.

Using a cutting tool, remove the section of subdash indicated. (Figure A)

Continue to Kit Assembly (Figure A)

2 1.800.221.0932 | MetraOnline.com

ISO DDIN radio provision 1.

Attach the

radio brackets

radio. (Figure A) to the radio using the screws supplied with the

2.

Locate the factory wiring harness and connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra. Test the radio for proper operation.

3.

Secure the completed assembly into the dash. Use the factory screws for the drivers side radio bracket and (1) #10 x 1/2” Phillips screw provided into the passenger side of the radio bracket.

4.

Reassemble the dash in reverse order of disassembly, using the

radio trim panel

instead of the factory panel.

(Figure A)

KIT ASSEMBLY

REV. 1/4/2018 INST95-3009 3

95-3009

I N S TA L L AT I O N I N S T R U C T I O N S

IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

Metra. The World’s Best Kits.

®

MetraOnline.com

© COPYRIGHT 2017 METRA ELECTRONICS CORPORATION ®

K NOWLEDGE IS P OWER

E nhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.

Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

REV. 1/4/18 INST95-3009

95-3009

I N S T R U C C I O N E S D E I N S TA L AC I Ó N

Chevrolet

Camaro

1993-1996

CARACTERÍSTICAS DEL KIT

• Provisión de radio ISO DDIN • El panel de acabado de repuesto está texturizado para que coincida con el acabado de fábrica

INDICE

Desmontaje del tablero ........................................2

Preparación del kit .................................................2

Ensamble del kit ....................................................3

CABLEADO Y CONEXIONES DE ANTENA

(se venden por separado) Arnés de cables: • 70-1858 Adaptador de antena: • 40-GM10

COMPONENTES DEL KIT

• A) Panel de moldura del radio • B) Soportes ISO DDIN • C) (1) tornillos Phillips #10 de 1/2” A B C

HERRAMIENTAS REQUERIDAS

• Herramienta para quitar paneles • Destornillador Phillips • Llave de tubo 9/32”, 10mm • Herramienta de corte

¡PRECAUCIÓN! Todos los accesorios, interruptores, paneles de controles de clima y especialmente las luces del indicador de las bolsas de aire deben estar conectados antes ciclar la ignición. Además, no quite el radio de fábrica con la llave en la posición o de encendido ni con el vehículo funcionando.

The World’s best kits.

®

MetraOnline.com

© COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 1/4/18 INST95-3009

DESMONTAJE DEL TABLERO

1.

Quite los (2) tornillos Phillips de la parte de arriba del lado del chofer. (Figura A)

2.

Quite los (2) tornillos de 9/32” de la parte de abajo del protector de la rodilla.

3.

Abra el compartimiento para los guantes y quite los (3) tornillos de 9/32” expuestos en el lado derecho de la terminación del cajón del radio y quite el cajón. (Figura A)

4.

Quite los (2) torninllos de 9/32” que aseguran el lado derecho de la unidad central y (1) tornillo de 10 mm que asegura el lado derecho.

5.

Saque la unidad del tablero y desconecte el cableado.

Continuar la preparación del kit (Figura A)

PREPARACIÓN DEL KIT

1.

Usando una herramienta de corte, quite la sección de subdash indicada. (Figura A)

Continúe con el ensamble del kit (Figura A)

2 1.800.221.0932 | MetraOnline.com

Provisión de radio ISO DDIN 1.

Una los

soportes al radio

(Figura A) usando los tornillos que vienen con el radio.

2.

Localice el arnés de cableado de fábrica y el conector de la antena en el tablero y realice todas las conexiones necesarias al radio. Metra recomienda el uso de adaptadores adecuados de acoplamiento de Metra. Pruebe el radio para verificar si funciona bien.

3.

Asegure el conjunto completo en el tablero. Use los tornillos de fábrica para el soporte del radio del lado del conductor y (1) tornillo Phillips # 10 x 1/2” proporcionado en el lado del pasajero del soporte del radio.

4.

Vuelva a ensamblar el tablero en el orden inverso al de desmontaje, utilizando el

panel de moldura de radio

en lugar del panel de fábrica.

(Figura A)

ENSAMBLE DEL KIT

REV. 1/4/2018 INST95-3009 3

The World’s best kits.

®

95-3009

I N S T R U C C I O N E S D E I N S TA L AC I Ó N

IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.

MetraOnline.com

© COPYRIGHT 2018 METRA ELECTRONICS CORPORATION ® E

EL CONOCIMIENTO ES PODER K NOWLEDGE IS

avance hacia un futuro mejor.

P OWER

fabricación inscribiéndose en la escuela de dispositivos electrónicos móviles más reconocida y respetada de nuestra industria. Regístrese en www.installerinstitute.com o llame al 800-354-6782 para obtener más información y

Metra recomienda MECP Técnicos certificados

REV. 1/4/18 INST95-3009

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement