Grizzly G0513X2BF 2 HP Extreme-Series Bandsaw Owner Manual

Grizzly G0513X2BF 2 HP Extreme-Series Bandsaw Owner Manual
MODEL G0513 SERIES
HEAVY-DUTY 17" BANDSAW
OWNER'S MANUAL
(MODELS G0513, G0513ANV
& EXTREME MODELS G0513X2, G0513X2B,
G0513X2BF & G0513X2F)
Model
G0513X2F
For Models
G0513,
G0513X2,
G0513X2BF,
G0513X2F
Only
Model
G0513X2B
For Model
G0513X2B
Only
COPYRIGHT © NOVEMBER, 2012 BY GRIZZLY INDUSTRIAL, INC. REVISED NOVEMBER, 2018 (MN)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
(FOR MACHINES MFD. SINCE 07/18) #TS15097 PRINTED IN TAIWAN
V3.11.18
This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and comprehension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
•
•
•
Lead from lead-based paints.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.
Table of Contents
INTRODUCTION................................................ 3
Manual Accuracy............................................ 3
Contact Info.................................................... 3
G0513 Series Combination Manual................ 3
Basic Controls................................................. 4
Control Panel................................................ 4
Front Controls............................................... 4
Motor Brake.................................................. 4
Rear Controls............................................... 5
G0513 Series Combination Data Sheet......... 6
SECTION 1: SAFETY........................................ 8
Safety Instructions for Machinery................... 8
Additional Safety for Bandsaws.................... 10
SECTION 2: POWER SUPPLY....................... 11
Availability................................................... 11
Full-Load Current Rating............................ 11
Circuit Information...................................... 11
Circuit Requirements.................................. 12
Grounding Requirements........................... 12
Extension Cords......................................... 14
Voltage Conversion.................................... 14
SECTION 3: SETUP........................................ 15
Unpacking..................................................... 15
Needed for Setup.......................................... 15
Hardware Recognition Chart........................ 16
Inventory....................................................... 17
G0513 & G0513ANV.................................. 17
G0513X2.................................................... 18
G0513X2F.................................................. 19
G0513X2B & G0513X2BF.......................... 20
Cleanup......................................................... 21
Site Considerations....................................... 22
Floor Load.................................................. 22
Placement Location.................................... 22
Moving & Placing Bandsaw.......................... 22
Using Eye Bolt............................................ 22
Using Wood Blocks.................................... 23
Mounting....................................................... 23
Bolting to Concrete Floors.......................... 23
Assembly...................................................... 24
Installing Guide Post Handwheel, Positive
Stop Bolt, & Table...................................... 24
Installing Fence (G0513, G0513ANV,
G0513X2 & G0513X2F)............................. 25
Installing
Fence
(G0513X2B
&
G0513X2BF)............................................... 26
Installing Resaw Fence (G0513X2,
G0513X2B, G0513X2BF & G0513X2F)..... 27
Initial Blade Tracking.................................... 28
Adjusting Positive Stop................................. 29
Dust Collection.............................................. 30
Power Cord Connection (G0513X2BF &
G0513X2F)................................................... 31
Test Run....................................................... 32
Tensioning Blade.......................................... 33
Flutter Method............................................ 33
Deflection Method....................................... 34
Adjusting Blade Support Bearings................ 35
Adjusting Blade Guides................................ 36
Adjusting Blade Guides (G0513 &
G0513ANV)................................................ 37
Adjusting Blade Guide Bearings
(G0513X2, G0513X2B, G0513X2BF, &
G0513X2F)................................................. 38
Aligning Table............................................... 39
Aligning Fence.............................................. 40
Aligning Fence (G0513, G0513ANV,
G0513X2 & G0513X2F)............................. 40
Aligning
Fence
(G0513X2B
&
G0513X2BF)............................................... 41
Calibrating Miter Gauge................................ 41
SECTION 4: OPERATIONS............................ 42
Operation Overview...................................... 42
Disabling & Locking Switch (G0513,
G0513ANV, G0513X2)................................. 43
Disabling & Locking Switch (G0513X2B,
G0513X2BF, G0513X2F)............................. 43
General Overview......................................... 44
Straight Cuts............................................... 44
Irregular Cuts.............................................. 44
Basic Cutting Tips...................................... 44
Workpiece Inspection................................... 44
Table Tilt....................................................... 45
Models G0513 & G0513ANV..................... 45
Models
G0513X2,
G0513X2B,
G0513X2BF & G0513X2F.......................... 45
Guide Post.................................................... 46
Fine Tune Tracking....................................... 46
Blade Selection............................................. 47
Blade Length.............................................. 47
Blade Width................................................ 47
Blade Material............................................. 47
Tooth Set.................................................... 48
Tooth Type................................................. 48
Blade Selection Chart................................... 49
Blade Breakage............................................ 50
Blade Care & Break-In.................................. 50
Blade Changes............................................. 51
Removing Blade......................................... 51
Installing Blade........................................... 51
Blade Speed................................................. 52
Crosscutting.................................................. 53
Resawing...................................................... 53
Cutting Curves.............................................. 54
Stacked Cuts................................................ 55
SECTION 5: ACCESSORIES.......................... 56
Basic Eye Protection.................................. 57
SECTION 6: MAINTENANCE.......................... 58
Schedule....................................................... 58
Wheel Brush................................................. 58
Cleaning & Protecting................................... 58
Lubrication.................................................... 58
Blade Post Rack......................................... 58
Tension Adjustment Assembly................... 59
Trunnions.................................................... 59
SECTION 7: SERVICE.................................... 60
Troubleshooting............................................ 60
V-Belt Service............................................... 63
Checking V-Belt.......................................... 63
Replacing V-Belt......................................... 63
Blade Lead.................................................... 64
Adjusting Wheel Brush................................. 65
Adjusting Tension Lever............................... 65
Adjusting Guide Post Travel......................... 66
Checking/Adjusting Guide Post Parallel
with Blade Side-to-Side.............................. 66
Checking/Adjusting Guide Post Parallel
with Blade Front-to-Back............................ 67
Aligning Wheels............................................ 68
Checking Coplanarity................................. 68
Shimming Upper Wheel............................. 69
Adjusting Lower Wheel............................... 70
Magnetic Brake Adjustment (G0513X2B,
G0513X2BF)................................................. 70
SECTION 8: WIRING....................................... 71
Wiring Safety Instructions............................. 71
G0513, G0513ANV & G0513X2 Wiring
Diagram........................................................ 72
G0513X2B Wiring Diagram.......................... 73
G0513X2BF Wiring Diagram........................ 74
G0513X2F 220V Wiring Diagram................. 75
G0513X2F 110V Wiring Diagram................. 76
SECTION 9: PARTS........................................ 77
G0513 & G0513ANV Main........................... 77
G0513 & G0513ANV Table, Trunnion &
Lower Blade Guides..................................... 79
G0513 & G0513ANV Fence......................... 80
G0513 & G0513ANV Upper Blade Guides
& Miter Gauge............................................... 81
G0513 Labels............................................... 83
G0513ANV Labels........................................ 84
G0513X2 Main.............................................. 85
G0513X2 Labels........................................... 87
G0513X2B Main........................................... 88
G0513X2B Labels......................................... 90
G0513X2BF Main......................................... 91
G0513X2BF Labels...................................... 93
G0513X2F Main............................................ 94
G0513X2F Labels......................................... 96
G0513X2, G0513X2B, G0513X2BF &
G0513X2F Guides & Trunnions................... 97
G0513X2 & G0513X2F Fence Assembly &
Table............................................................. 99
G0513X2B & G0513X2BF Fence Assembly
& Table....................................................... 100
G0513X2BF & G0513X2F Foot Brake....... 101
WARRANTY & RETURNS............................ 105
INTRODUCTION
Manual Accuracy
Contact Info
We are proud to provide a high-quality owner’s
manual with your new machine!
We stand behind our machines! If you have questions or need help, contact us with the information
below. Before contacting, make sure you get the
serial number and manufacture date from the
machine ID label. This will help us help you faster.
We made every effort to be exact with the instructions, specifications, drawings, and photographs
in this manual. Sometimes we make mistakes, but
our policy of continuous improvement also means
that sometimes the machine you receive is
slightly different than shown in the manual.
If you find this to be the case, and the difference
between the manual and machine leaves you
confused or unsure about something, check our
website for an updated version. We post current
manuals and manual updates for free on our website at www.grizzly.com.
Alternatively, you can call our Technical Support
for help. Before calling, make sure you write down
the Manufacture Date and Serial Number from
the machine ID label (see below). This information
is required for us to provide proper tech support,
and it helps us determine if updated documentation is available for your machine.
Manufacture Date
Serial Number
G0513 Series Bandsaws (Mfd. Since 07/18)
Grizzly Technical Support
1815 W. Battlefield
Springfield, MO 65807
Phone: (570) 546-9663
Email: techsupport@grizzly.com
We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.
Grizzly Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Email: manuals@grizzly.com
G0513 Series
Combination Manual
The G0513 Series Bandsaws share many similarities. Thus, this combination manual includes information for all seven models of the G0513 Series
Bandsaws.
Unless otherwise specified, information applies to
all models. Headers are used to identify information that only applies to specific models.
-3-
Basic Controls
Refer to Figures 1–4 and the following descriptions to become familiar with the basic controls
and components of your bandsaw. Knowledge of
these controls and terminology will help you better
understand this manual.
Control Panel
The 2-button power switch on Models G0513,
G0513ANV, and G0513X2 is located on the column for easy access (see Figure 1). The power
button can be disabled with a padlock to prevent
unauthorized startup of the bandsaw (refer to
Page 43 for additional details).
Front Controls
A. Blade Tension Scale: Allows for easy monitoring of blade tension in arbitrary numbers
1–8.
B. Blade Tension Handwheel: Tensions blade
in gradual increments.
C. Blade Tracking Window: Allows you to
monitor blade tracking on the wheel without
opening the wheel cover.
D. Fence and Miter Gauge: Supports workpiece
for controlled straight or angled cuts.
C
A
B
D
Figure 1. 2-Button power switch.
E
The Models G0513X2B, G0513X2BF, and
G0513X2F feature a power switch that can be
disabled with a key to prevent unauthorized starting of the machine (see Figure 2). To disable
the switch, turn the key to "0" and remove it. To
enable the switch, insert the key and turn it to "1."
Figure 3. Front controls
(G0513X2BF shown).
Power Switch
Key
On Button
E.
Foot Brake (Models G0513X2BF &
G0513X2F): Quickly stops bandsaw blade
and motor.
Motor Brake
Off Button
Figure 2. Control panel with a switch disabling
lock.
-4-
The Models G0513X2B and G0513X2BF have a
motor brake that activates and quickly stops the
blade when the OFF button is used, or the foot
pedal is pressed on the Model G0513X2BF.
G0513 Series Bandsaws (Mfd. Since 07/18)
Rear Controls
F.
Wheel Cover Lock Knobs: Secure the
wheel covers.
F
G
G. Quick-Release Blade Tension Lever:
Adjusts blade tension for quick blade changes.
H. Blade Tracking Knob and Lock Lever:
Moves and locks upper wheel tilt for blade
tracking.
I.
J.
Table Tilt Controls: Adjusts table tilt and
locks the table in place.
I
Magnetic Switch: Provides thermal overload
protection for the motor.
K. Lower Wheel Adjustment Hub: Used when
adjusting coplanarity of the wheels.
L.
H
L
J
K
F
Guide Post Handwheel and Lock Knob:
Quickly moves the upper guide post to the
desired height; locks setting.
Figure 4. Rear controls
(G0513X2B shown).
To reduce your risk of
serious injury, read this
entire manual BEFORE
using machine.
G0513 Series Bandsaws (Mfd. Since 07/18)
-5-
G0513 Series Combination Data Sheet
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
MODEL G0513 SERIES 17" BANDSAWS
Model Number
G0513/
G0513ANV
G0513X2
G0513X2B
G0513X2BF
G0513X2F
266 lbs.
325 lbs.
352 lbs.
357 lbs.
335 lbs.
460 lbs.
434 lbs.
Product Dimensions
Weight
Width (side-to-side) x Depth
(front-to-back) x Height
32" x 32" x 73"
Footprint (Length x Width)
27" x 17 3 ⁄4"
Shipping Dimensions
Type
Weight
Length x Width x Height
Wood Slat Crate
342 lbs.
418 lbs.
20" x 30" x 81"
31" x 21" x 81"
446 lbs.
31" x 20" x 81"
31" x 21" x 81"
220V, Single-Phase, 60 Hz
110V/220V,
Single-Phase,
60 Hz
8.7A
19A at 110V,
9.5A at 220V
15A
30A at 110V,
15A at 220V
Electrical
Power Requirement
110V/220V, Single-Phase, 60 Hz
Full Load Current
20A at 110V,
10A at 220V
Minimum Circuit Size
19A at 110V,
9.5A at 220V
30A at 110V, 15A at 220V
Prewired
Switch
Switch Voltage
220V
2-Button Power Switch
Magnetic w/Thermal Overload Protection
110V/220V
Cord Included
220V
Yes
Plug Included
110V/220V
No
No
Yes, NEMA 6-15
No
Motor
Type
TEFC Capacitor Start Induction
Horsepower
Voltage
2 HP
110V/220V
Phase
Amperage
220V
110V/220V
8.7A
19A at 110V,
9.5A at 220V
Single-Phase
20A at 110V,
10A at 220V
19A at 110V,
9.5A at 220V
Speed
1720 RPM
Cycle
60 Hz
Power Transfer
Belt Drive
Bearings
Shielded and Permanently Lubricated
Operation
Blade Speeds
Table Tilt
-6-
1700, 3500 FPM
Left 10°, Right
45°
Left 5°, Right 45°
G0513 Series Bandsaws (Mfd. Since 07/18)
Model Number
G0513/
G0513ANV
G0513X2
G0513X2B
G0513X2BF
G0513X2F
Cutting Capacities
Maximum Cutting Height
12 1⁄ 8"
12 "
Maximum Capacity Left of
Blade
16 1⁄4"
Blade Information
Standard Blade Length
131 1⁄ 2"
Blade Width Range
1
Blade Guides
⁄ 8"–1"
Roller Disc, Ball
Bearings
Ball Bearings
Guide Post Size
1.18" (30mm) Square
Guide Post Type
Square Tubing, 0.075" in Wall Thickness
Table Dimensions
Length x Width x Thickness
17" x 17" x 1 1⁄ 2"
23 5 ⁄ 8" x 17 1⁄4" x 1 1⁄ 2"
37 1⁄ 2"
Floor to Table Height
Fence Information
Locks in Front
Yes
Locks in Rear
No
Adjustable for Blade Lead
Resaw Fence Included
Yes
No
Yes
Construction
Table
Fence
Precision-Ground Cast Iron
Deluxe Extruded
Aluminum
Cast Iron Fence w/ Extruded Aluminum Resaw Fence
Body
Wheels
Re-Inforced Steel
ComputerBalanced Cast
Aluminum
Computer-Balanced Cast Iron
Wheel Tire
Polyurethane
Wheel Covers
Pre-Formed Steel
Paint
Powder Coated
Other Related Information
Foot Brake
No
Motor Brake
Yes
No
Yes
Wheel Diameter
16 ⁄4"
Wheel Width
1 1⁄4"
No
3
Dust Ports
2 at 4"
Mobile Base Model
D2057A
Other Specifications
Country of Origin
Taiwan
Warranty
1 Year
ISO Factory
Yes
Serial Number Location
ID Label on Upper Wheel Cover
Assembly Time
CSA Certified
1 Hour
G0513 Only
G0513 Series Bandsaws (Mfd. Since 07/18)
Yes
-7-
SECTION 1: SAFETY
For Your Own Safety, Read Instruction
Manual Before Operating This Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
NOTICE
Alerts the user to useful information about proper operation of the
machine to avoid machine damage.
Safety Instructions for Machinery
OWNER’S MANUAL. Read and understand this
owner’s manual BEFORE using machine.
TRAINED OPERATORS ONLY. Untrained operators have a higher risk of being hurt or killed.
Only allow trained/supervised people to use this
machine. When machine is not being used, disconnect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially
around children. Make your workshop kid proof!
DANGEROUS ENVIRONMENTS. Do not use
machinery in areas that are wet, cluttered, or have
poor lighting. Operating machinery in these areas
greatly increases the risk of accidents and injury.
MENTAL ALERTNESS REQUIRED. Full mental
alertness is required for safe operation of machinery. Never operate under the influence of drugs or
alcohol, when tired, or when distracted.
-8-
ELECTRICAL EQUIPMENT INJURY RISKS.
You can be shocked, burned, or killed by touching
live electrical components or improperly grounded
machinery. To reduce this risk, only allow qualified
service personnel to do electrical installation or
repair work, and always disconnect power before
accessing or exposing electrical equipment.
DISCONNECT POWER FIRST. Always disconnect machine from power supply BEFORE making adjustments, changing tooling, or servicing
machine. This prevents an injury risk from unintended startup or contact with live electrical components.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. Everyday
eyeglasses are NOT approved safety glasses.
G0513 Series Bandsaws (Mfd. Since 07/18)
WEARING PROPER APPAREL. Do not wear
clothing, apparel or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to reduce
risk of slipping and losing control or accidentally
contacting cutting tool or moving parts.
HAZARDOUS DUST. Dust created by machinery
operations may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece material. Always wear a NIOSH-approved respirator to
reduce your risk.
HEARING PROTECTION. Always wear hearing protection when operating or observing loud
machinery. Extended exposure to this noise
without hearing protection can cause permanent
hearing loss.
REMOVE ADJUSTING TOOLS. Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys, wrenches,
or any other tools on machine. Always verify
removal before starting!
USE CORRECT TOOL FOR THE JOB. Only use
this tool for its intended purpose—do not force
it or an attachment to do a job for which it was
not designed. Never make unapproved modifications—modifying tool or using it differently than
intended may result in malfunction or mechanical
failure that can lead to personal injury or death!
AWKWARD POSITIONS. Keep proper footing
and balance at all times when operating machine.
Do not overreach! Avoid awkward hand positions
that make workpiece control difficult or increase
the risk of accidental injury.
CHILDREN & BYSTANDERS. Keep children and
bystanders at a safe distance from the work area.
Stop using machine if they become a distraction.
GUARDS & COVERS. Guards and covers reduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged, and working correctly BEFORE
operating machine.
G0513 Series Bandsaws (Mfd. Since 07/18)
FORCING MACHINERY. Do not force machine.
It will do the job safer and better at the rate for
which it was designed.
NEVER STAND ON MACHINE. Serious injury
may occur if machine is tipped or if the cutting
tool is unintentionally contacted.
STABLE MACHINE. Unexpected movement during operation greatly increases risk of injury or
loss of control. Before starting, verify machine is
stable and mobile base (if used) is locked.
USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for recommended accessories. Using improper accessories will increase the risk of serious injury.
UNATTENDED OPERATION. To reduce the
risk of accidental injury, turn machine OFF and
ensure all moving parts completely stop before
walking away. Never leave machine running
while unattended.
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to keep
machine in good working condition. A machine
that is improperly maintained could malfunction,
leading to serious personal injury or death.
DAMAGED PARTS. Regularly inspect machine
for damaged, loose, or mis-adjusted parts—or
any condition that could affect safe operation.
Immediately repair/replace BEFORE operating
machine. For your own safety, DO NOT operate
machine with damaged parts!
MAINTAIN POWER CORDS. When disconnecting cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the cord
may damage the wires inside. Do not handle
cord/plug with wet hands. Avoid cord damage by
keeping it away from heated surfaces, high traffic
areas, harsh chemicals, and wet/damp locations.
EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the intended operation, stop using the machine! Contact our
Technical Support at (570) 546-9663.
-9-
Additional Safety for Bandsaws
Serious cuts, amputation, or death can occur from contact with the moving saw blade during
operation or if blade breakage occurs. To reduce this risk, anyone operating this machine
MUST completely heed the hazards and warnings below.
HAND PLACEMENT. Placing hands or fingers
in line with blade during operation may result in
serious injury if hands slip or workpiece moves
unexpectedly. Do not position fingers or hands in
line with blade, and never reach under table while
blade is moving.
SMALL/NARROW WORKPIECES. If hands slip
during a cut while holding small workpieces
with fingers, serious personal injury could occur.
Always support/feed small or narrow workpieces
with push sticks, push blocks, jig, vise, or some
type of clamping fixture.
BLADE SPEED. Cutting workpiece before blade
is at full speed could cause blade to grab workpiece and pull hands into blade. Allow blade to
reach full speed before starting cut. DO NOT start
machine with workpiece contacting blade.
FEED RATE. To avoid risk of workpiece slipping
and causing operator injury, always feed stock
evenly and smoothly.
BLADE CONDITION. Dull blades require more
effort to perform cut, increasing risk of accidents.
Do not operate with dirty, dull, cracked or badly
worn blades. Inspect blades for cracks and missing teeth before each use. Always maintain proper
blade tension and tracking while operating.
CLEARING JAMS AND CUTOFFS. Always stop
bandsaw and disconnect power before clearing
scrap pieces that get stuck between blade and
table insert. Use brush or push stick, not hands,
to clean chips/cutoff scraps from table.
BLADE CONTROL. To avoid risk of injury due to
blade contact, always allow blade to stop on its
own. DO NOT try to stop or slow blade with your
hand or the workpiece.
-10-
GUARDS/COVERS. Blade guards and covers
protect operator from the moving bandsaw blade.
The wheel covers protect operator from getting
entangled with rotating wheels or other moving
parts. ONLY operate this bandsaw with blade
guard in proper position and wheel covers completely closed.
BLADE REPLACEMENT. To avoid mishaps that
could result in operator injury, make sure blade
teeth face down toward table and blade is properly tensioned and tracked before operating.
UPPER BLADE GUIDE SUPPORT. To reduce
exposure of operator to blade and provide maximum blade support while cutting, keep upper
blade guides adjusted to just clear workpiece.
CUTTING TECHNIQUES. To avoid blade getting
pulled off wheels or accidentally breaking and
striking operator, always turn bandsaw OFF and
wait for blade to come to a complete stop before
backing workpiece out of blade. DO NOT back
workpiece away from blade while bandsaw is running. DO NOT force or twist blade while cutting,
especially when sawing small curves. This could
result in blade damage or breakage.
WORKPIECE SUPPORT. To maintain maximum
control and reduce risk of blade contact/breakage, always ensure adequate support of long/
large workpieces. Always keep workpiece flat and
firm against table/fence when cutting to avoid loss
of control. If necessary, use a jig or other workholding device.
WORKPIECE MATERIAL. This machine is
intended for cutting natural and man-made wood
products, and laminate covered wood products.
This machine is NOT designed to cut metal,
glass, stone, tile, etc.
G0513 Series Bandsaws (Mfd. Since 07/18)
SECTION 2: POWER SUPPLY
Availability
Before installing the machine, consider the availability and proximity of the required power supply
circuit. If an existing circuit does not meet the
requirements for this machine, a new circuit must
be installed. To minimize the risk of electrocution,
fire, or equipment damage, installation work and
electrical wiring must be done by an electrician or
qualified service personnel in accordance with all
applicable codes and standards.
Electrocution, fire, shock,
or equipment damage
may occur if machine is
not properly grounded
and connected to power
supply.
Full-Load Current Rating
The full-load current rating is the amperage a
machine draws at 100% of the rated output power.
On machines with multiple motors, this is the
amperage drawn by the largest motor or sum of all
motors and electrical devices that might operate
at one time during normal operations.
G0513 & G0513ANV Full-Load Current Rating
At 110V...................................................20 Amps
At 220V..................................................10 Amps
The full-load current is not the maximum amount
of amps that the machine will draw. If the machine
is overloaded, it will draw additional amps beyond
the full-load rating.
If the machine is overloaded for a sufficient length
of time, damage, overheating, or fire may result—
especially if connected to an undersized circuit.
To reduce the risk of these hazards, avoid overloading the machine during operation and make
sure it is connected to a power supply circuit that
meets the specified circuit requirements.
Circuit Information
A power supply circuit includes all electrical
equipment between the breaker box or fuse panel
in the building and the machine. The power supply circuit used for this machine must be sized to
safely handle the full-load current drawn from the
machine for an extended period of time. (If this
machine is connected to a circuit protected by
fuses, use a time delay fuse marked D.)
Note: Circuit requirements in this manual apply to
a dedicated circuit—where only one machine will
be running on the circuit at a time. If machine will
be connected to a shared circuit where multiple
machines may be running at the same time, consult an electrician or qualified service personnel to
ensure circuit is properly sized for safe operation.
G0513X2 & G0513X2F Full-Load Current Rating
At 110V...................................................19 Amps
At 220V.................................................9.5 Amps
G0513X2B & G0513X2BF Full-Load Current
Rating
At 220V......................................................... 8.7A
G0513 Series Bandsaws (Mfd. Since 07/18)
-11-
Circuit Requirements
These machines are prewired to operate on a 220V power supply circuit that has a verified ground and meet
the 220V operation requirements listed below.
Models G0513, G0513ANV, G0513X2, and G0513X2F can be converted to operate on a 110V power supply
(refer to Voltage Conversion instructions beginning on Page 14) that has a verified ground and meets the
220V operation requirements listed below.
Model Number
G0513, G0513ANV, G0513X2, G0513X2F
Circuit Requirements For 220V Operation:
Nominal Voltage
G0513X2B & G0513X2BF
220V/240V
Cycle
60 Hz
Phase
Single-Phase
Power Supply Circuit
15 Amps
Plug/Receptacle
NEMA 6-15
Power Cord
Circuit Requirements For 110V Operation:
Nominal Voltage
“S”-Type, 3-Wire, 14 AWG, 300 VAC
110V/120V
Cycle
60 Hz
Phase
Single-Phase
Power Supply Circuit
Plug/Receptacle
Power Cord
N/A
30 Amps
NEMA L5-30
“S”-Type, 3-Wire, 12 AWG, 300 VAC
Grounding Requirements
This machine MUST be grounded. In the event
of certain malfunctions or breakdowns, grounding
reduces the risk of electric shock by providing a
path of least resistance for electric current.
GROUNDED
6-15 RECEPTACLE
Current Carrying Prongs
6-15 PLUG
Grounding Requirements for 220V: The plug
specified under “Circuit Requirements for 220V
Operation” on this page has a grounding pin that
must be attached to the equipment-grounding
wire inside the specified power cord. The plug
must only be inserted into a matching receptacle (see Figure 5) that is properly installed and
grounded in accordance with all local codes and
ordinances.
-12-
Grounding Pin
Figure 5. Typical 6-15 plug and receptacle.
G0513 Series Bandsaws (Mfd. Since 07/18)
Improper connection of the equipment-grounding
wire can result in a risk of electric shock. The
wire with green insulation (with or without yellow
stripes) is the equipment-grounding wire. If repair
or replacement of the power cord or plug is necessary, do not connect the equipment-grounding
wire to a live (current carrying) terminal.
No adapter should be used with plug. If
plug does not fit available receptacle, or if
machine must be reconnected for use on a
different type of circuit, reconnection must
be performed by an electrician or qualified
service personnel, and it must comply with
all local codes and ordinances.
Grounding Requirements for 110V: The plug
specified under “Circuit Requirements for 110V
Operation” on the previous page has a grounding
prong that must be attached to the equipmentgrounding wire inside the specified power cord.
The plug must only be inserted into a matching
receptacle (see Figure 6) that is properly installed
and grounded in accordance with all local codes
and ordinances.
L5-30 GROUNDED
LOCKING
RECEPTACLE
Check with a qualified electrician or service personnel if you do not understand these grounding
requirements, or if you are in doubt about whether
the tool is properly grounded. If you ever notice
that a cord or plug is damaged or worn, disconnect it from power, and immediately replace it with
a new one.
Serious injury could occur if you connect
machine to power before completing setup
process. DO NOT connect to power until
instructed later in this manual.
For your own safety and protection of
property, consult an electrician if you are
unsure about wiring practices or electrical
codes in your area.
Neutral
L5-30
LOCKING
PLUG
Hot
Grounding Prong
is Hooked
Figure 6. Typical L5-30 plug and receptacle.
G0513 Series Bandsaws (Mfd. Since 07/18)
-13-
Extension Cords
Voltage Conversion
We do not recommend using an extension cord
with this machine. If you must use an extension
cord, only use it if absolutely necessary and only
on a temporary basis.
The voltage conversion MUST be performed by
an electrician or a qualified service personnel.
Extension cords cause voltage drop, which can
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).
Any extension cord used with this machine must
be in good condition and contain a ground wire
and matching plug/receptacle. Additionally, it must
meet the following size requirements:
Minimum Gauge Size at 220V..............14 AWG
Minimum Gauge Size at 110V...............12 AWG
Maximum Length (Shorter is Better).......50 ft.
Models G0513, G0513ANV, & G0513X2
To perform the voltage conversion, install the
correct plug and rewire the motor to the new voltage, according to the wiring diagram provided on
Page 71.
Model G0513X2F
To perform the voltage conversion, replace the
magnetic switch with the 110V version (Part No.
P0513X2F244), install the correct power cord
and plug, and rewire the motor to the new voltage, according to the wiring diagram provided on
Page 75.
If the diagram included on the motor conflicts with the one in this manual, the motor
may have changed since the manual was
printed. Use the diagram provided on the
motor.
-14-
G0513 Series Bandsaws (Mfd. Since 07/18)
SECTION 3: SETUP
This machine presents
serious injury hazards
to untrained users. Read
through this entire manual to become familiar with
the controls and operations before starting the
machine!
Wear safety glasses during
the entire setup process!
HEAVY LIFT!
Straining or crushing injury
may occur from improperly
lifting machine or some of
its parts. To reduce this risk,
get help from other people
and use a forklift (or other
lifting equipment) rated for
weight of this machine.
Unpacking
This machine was carefully packaged for safe
transport. When unpacking, separate all enclosed
items from packaging materials and inspect them
for shipping damage. If items are damaged,
please call us immediately at (570) 546-9663.
SUFFOCATION HAZARD!
Keep children and pets away
from plastic bags or packing
materials shipped with this
machine.
Needed for Setup
The following items are needed, but not included,
for the setup/assembly of this machine.
Description
Qty
•
Additional People........................................ 1
•
Safety Glasses..........................1 per Person
•
Cleaner/Degreaser...................... As Needed
•
Disposable Shop Rags................ As Needed
•
Forklift/Strap or Chain w/Lifting Hook
(Each component rated for at least 1000 lbs)
........................................................... 1 Each
•
1x4 & 2x4 Shims (Optional)................ 1 Each
•
Feeler Gauges 0.004", 0.016"............. 1 Each
•
Straightedge................................................ 1
•
Fine Ruler.................................................... 1
•
Machinist's Square...................................... 1
•
Phillips Screwdriver #2................................ 1
•
Hex Wrench 6mm........................................ 1
•
Dust Collection System............................... 1
•
Dust Hose 4"............................................... 2
•
Hose Clamps 4".......................................... 2
IMPORTANT: Save all packaging materials until
you are completely satisfied with the machine and
have resolved any issues between Grizzly or the
shipping agent. You MUST have the original packaging to file a freight claim. It is also extremely
helpful if you need to return your machine later.
G0513 Series Bandsaws (Mfd. Since 07/18)
-15-
Hardware Recognition Chart
USE THIS CHART TO MATCH UP
HARDWARE DURING THE INVENTORY
AND ASSEMBLY PROCESS.
Flat
Head
Cap
Screw
5mm
5mm
-16-
G0513 Series Bandsaws (Mfd. Since 07/18)
Inventory
The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
C
B
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
G0513 & G0513ANV
Shipping Inventory (Figures 7–8)
Qty
A. Bandsaw (not shown).................................. 1
B. Table............................................................ 1
C. Miter Gauge................................................. 1
D. Rear Rail..................................................... 1
E. Front Rail . .................................................. 1
F. Fence Assembly.......................................... 1
G. Guide Post Handwheel............................... 1
Hardware & Tools (Not Shown)
Qty
•
Flat Washers 8mm (Table).......................... 4
•
Lock Washers 8mm (Table)........................ 4
•
Hex Bolts M8-1.25 x 16 (Table)................... 4
•
Hex Bolt M8-1.25 x 90 (Positive Stop)......... 1
•
Hex Nuts M8-1.25 (Positive Stop, Fence)... 2
•
Cap Screws M6-1 x 16 (Fence)................... 2
•
Hex Bolts M6-1 x 20 (Fence)....................... 2
•
Lock Washers 6mm (Fence)....................... 2
•
Flat Washers 6mm (Fence)......................... 2
•
Hex Nut M6-1 (Fence)................................. 1
•
Table Pin..................................................... 1
•
Table Insert.................................................. 1
•
Fence Handle M8-1.25 x 22 (Fence)........... 1
•
Rail Pad M6-1 x 18 (Fence)......................... 1
•
Hex Wrench 5mm, 8mm.................... 1 Each
•
Open-End Wrench 10 x 13mm.................... 1
Figure 7. Table and miter gauge.
D
E
F
G
Figure 8. Other bandsaw components.
NOTICE
If you cannot find an item on this list, carefully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpacking or they are pre-installed at the factory.
SUFFOCATION HAZARD!
Keep children and pets away
from plastic bags or packing
materials shipped with this
machine.
G0513 Series Bandsaws (Mfd. Since 07/18)
-17-
G0513X2
Shipping Inventory (Figures 9–10)
Qty
A. Bandsaw (not shown).................................. 1
B. Table............................................................ 1
C. Miter Gauge................................................. 1
D. Rear Rail..................................................... 1
E. Resaw Fence ............................................. 1
F. Front Rail..................................................... 1
G. Fence Assembly.......................................... 1
H. Guide Post Handwheel............................... 1
Hardware & Tools (Not Shown)
Qty
•
Flat Washers 8mm (Table, Fence, Rail)...... 5
•
Lock Washers 8mm (Table, Rail)................ 4
•
Hex Bolts M8-1.25 x 25 (Table)................... 4
•
Hex Bolt M8-1.25 x 90 (Positive Stop)......... 1
•
Hex Nuts M8-1.25 (Positive Stop, Fence)... 2
•
Cap Screws M6-1 x 16 (Rear Rail).............. 2
•
Hex Bolt M6-1 x 20 (Front Rail)................... 2
•
Lock Washers 6mm (Rail)........................... 2
•
Flat Washers 6mm (Rail)............................. 2
•
Table Pin..................................................... 1
•
Table Insert.................................................. 1
•
Locking Handle M8-1.25 x 44 (Fence)........ 1
•
Fence Handle M8-1.25 x 22 (Fence)........... 1
•
Moving Plate (Fence).................................. 1
•
Hex Wrench 5mm, 8mm.................... 1 Each
•
Open-End Wrench 10 x 13mm.................... 1
C
B
Figure 9. Table and miter gauge.
E
D
F
G
H
Figure 10. Other bandsaw components.
-18-
G0513 Series Bandsaws (Mfd. Since 07/18)
G0513X2F
Shipping Inventory (Figures 11–12)
Qty
A. Bandsaw (not shown).................................. 1
B. Table............................................................ 1
C. Miter Gauge................................................. 1
D. Rear Rail..................................................... 1
E. Resaw Fence ............................................. 1
F. Front Rail..................................................... 1
G. Fence Assembly.......................................... 1
H. Guide Post Handwheel............................... 1
Hardware & Tools (Not Shown)
Qty
•
Flat Washers 8mm (Table, Fence, Rail)...... 5
•
Lock Washers 8mm (Table, Rail)................ 4
•
Hex Bolts M8-1.25 x 25 (Table)................... 4
•
Hex Bolt M8-1.25 x 90 (Positive Stop)......... 1
•
Hex Nuts M8-1.25 (Positive Stop, Fence)... 2
•
Cap Screws M6-1 x 16 (Rear Rail).............. 2
•
Hex Bolt M6-1 x 20 (Front Rail)................... 2
•
Lock Washers 6mm (Rail)........................... 2
•
Flat Washers 6mm (Rail)............................. 2
•
Table Pin..................................................... 1
•
Table Inserts................................................ 2
•
Locking Handle M8-1.25 x 44 (Fence)........ 1
•
Fence Handle M8-1.25 x 22 (Fence)........... 1
•
Moving Plate (Fence).................................. 1
•
Hex Wrench 5mm, 8mm.................... 1 Each
•
Open-End Wrench 10 x 13mm.................... 1
C
B
Figure 11. Table and miter gauge.
E
D
F
G
H
Figure 12. Other bandsaw components.
G0513 Series Bandsaws (Mfd. Since 07/18)
-19-
G0513X2B & G0513X2BF
Shipping Inventory (Figures 13–14)
Qty
A. Bandsaw (not shown).................................. 1
B. Table............................................................ 1
C. Miter Gauge................................................. 1
D. Resaw Fence.............................................. 1
E. Front Rail..................................................... 1
F. Fence Assembly.......................................... 1
G. Guide Post Handwheel............................... 1
Hardware & Tools (Not Shown)
Qty
•
Flat Washers 8mm (Table, Fence, Rail)...... 8
•
Lock Washers 8mm (Table, Rail)................ 5
•
Hex Bolts M8-1.25 x 25 (Table)................... 4
•
Hex Bolt M8-1.25 x 90 (Positive Stop)......... 1
•
Hex Nut M8-1.25 (Positive Stop)................. 1
•
Cap Screws M6-1 x 20 (Rail)...................... 3
•
Cap Screw M8-1.25 x 20 (Rail)................... 1
•
Lock Washers 6mm (Rail)........................... 3
•
Flat Washers 6mm (Rail)............................. 3
•
Table Pin..................................................... 1
•
Table Inserts................................................ 2
•
Locking Handle M8-1.25 x 44 (Fence)........ 1
•
Moving Plate (Fence).................................. 1
•
Knobs M8-1.25 x 20.................................... 2
•
Rail Plates................................................... 3
•
Hex Wrench 5mm, 8mm.................... 1 Each
•
Open End Wrench 10 x 13mm.................... 1
C
B
Figure 13. Table and miter gauge.
D
E
F
G
Figure 14. Other bandsaw components.
-20-
G0513 Series Bandsaws (Mfd. Since 07/18)
Cleanup
The unpainted surfaces of your machine are
coated with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
This rust preventative works extremely well, but it
will take a little time to clean.
Be patient and do a thorough job cleaning your
machine. The time you spend doing this now will
give you a better appreciation for the proper care
of your machine's unpainted surfaces.
There are many ways to remove this rust preventative, but the following steps work well in a wide
variety of situations. Always follow the manufacturer’s instructions with any cleaning product you
use and make sure you work in a well-ventilated
area to minimize exposure to toxic fumes.
Before cleaning, gather the following:
•
Disposable rags
•
Cleaner/degreaser (WD•40 works well)
•
Safety glasses & disposable gloves
•
Plastic paint scraper (optional)
Basic steps for removing rust preventative:
1.
Put on safety glasses.
2.
Coat the rust preventative with a liberal
amount of cleaner/degreaser, then let it soak
for 5–10 minutes.
3.
Wipe off the surfaces. If your cleaner/
degreaser is effective, the rust preventative
will wipe off easily. If you have a plastic paint
scraper, scrape off as much as you can first,
then wipe off the rest with the rag.
4.
Repeat Steps 2–3 as necessary until clean,
then coat all unpainted surfaces with a quality
metal protectant to prevent rust.
G0513 Series Bandsaws (Mfd. Since 07/18)
Gasoline and petroleum
products have low flash
points and can explode
or cause fire if used to
clean machinery. Avoi d
u sing t h e s e p r o d u c t s
to c l e a n m a c hin e r y.
Many cleaning solvents
are toxic if inhaled. Only
work in a well-ventilated
area.
NOTICE
Avoid harsh solvents like acetone or brake
parts cleaner that may damage painted surfaces. Always test on a small, inconspicuous location first.
T23692—Orange Power Degreaser
A great product for removing the waxy shipping grease from the non-painted parts of the
machine during clean up.
Figure 15. T23692 Orange Power Degreaser.
-21-
Site Considerations
Moving & Placing
Bandsaw
Floor Load
Refer to the Machine Data Sheet for the weight
and footprint specifications of your machine.
Some residential floors may require additional
reinforcement to support both the machine and
operator.
This bandsaw is a heavy
machine. Serious personal
injury may occur if safe
moving methods are not
used. Get assistance and
use power equipment to
move the shipping crate
and remove the machine
from the shipping pallet.
Placement Location
Consider existing and anticipated needs, size of
material to be processed through each machine,
and space for auxiliary stands, work tables or
other machinery when establishing a location for
your new machine. See Figure 16 for the minimum working clearances.
Special care should be taken when moving this
bandsaw. Only use one of the following methods
to lift or move this bandsaw.
Using Eye Bolt
1.
Move the crate to the prepared location, then
remove the crate from the shipping pallet.
2.
Unbolt the bandsaw from the pallet.
3.
Place the lifting hook through the eye bolt at
the top of the machine (see Figure 17), and
lift the bandsaw slowly with a forklift.
32"
32"
Figure 16. Minimum working clearances.
Children and visitors may be
seriously injured if unsupervised around this machine.
Lock entrances to the shop
or disable start switch or
power connection to prevent
unsupervised use.
Eye Bolt
Figure 17. Lifting the bandsaw.
4.
-22-
Remove the pallet and slowly set the bandsaw
into position.
G0513 Series Bandsaws (Mfd. Since 07/18)
Using Wood Blocks
1.
Move the crate to the prepared location, then
remove the crate from the shipping pallet.
2.
Unbolt the bandsaw from the pallet.
3.
Carefully place the forklift forks under the
head and insert a 1x4 block between the head
and the left fork and a 2x4 block between the
head and right fork so the bandsaw is level,
as shown in Figure 18.
Mounting
We recommend mounting your new machine to
the floor. Because floor materials may vary, floor
mounting hardware is not included. You may also
mount your machine to a mobile base that has
wheel locking or wheel retracting capabilities that
keeps the mobile base from rolling when not in
use.
Bolting to Concrete Floors
2x4
1x4
Lag shield anchors with lag bolts (see Figure 19)
and anchor studs (see Figure 20) are two popular
methods for anchoring an object to a concrete
floor. We suggest you research the many options
and methods for mounting your machine and
choose the best that fits your specific application.
Figure 18. Example photo of lifting bandsaw with
forklift using wood shims.
4.
Lift the bandsaw off of the pallet, remove the
pallet, then slowly set the bandsaw into position.
Figure 19. Typical lag shield anchor and bolt.
Note: If you are concerned about your forklift
forks hitting the tension handwheel, remove the
handwheel before positioning the forks, then reinstall it after placing.
Serious injury could occur if you connect
machine to power before completing setup
process. DO NOT connect to power until
instructed later in this manual.
Figure 20. Typical anchor stud.
Anchor studs are stronger and more permanent alternatives to lag shield anchors;
however, they will stick out of the floor,
which may cause a tripping hazard if you
decide to move your machine.
G0513 Series Bandsaws (Mfd. Since 07/18)
-23-
Assembly
4.
Loosen blade tension by rotating the quickrelease tension lever clockwise, as shown in
Figure 23.
Installing Guide Post Handwheel,
Positive Stop Bolt, & Table
1.
Secure the guide post handwheel onto the
handwheel shaft flat with the included set
screw (see Figure 21).
Loosen
Tighten
Guide Post
Handwheel
Figure 23. Quick-release tension lever.
5.
Adjust the upper and lower blade guides
away from the blade. Refer to Adjusting
Blade Guides beginning on Page 36 for
more details.
Figure 21. Guide post handwheel installed.
2.
Thread the M8-1.25 hex nut halfway onto the
M8-1.25 x 90 hex bolt (this is the positive stop
bolt).
3.
Thread the positive stop bolt into the threaded hole on bandsaw body (see Figure 22).
Positive Stop
All saw blades are dangerous and may cause personal injury. To reduce the
risk of being injured, wear
leather gloves when handling saw blades.
6.
Remove the saw blade (refer to Blade
Changes on Page 51 for detailed instructions).
7.
With the help of another person, lift the table
onto the trunnions.
Figure 22. Positive stop bolt installed.
-24-
G0513 Series Bandsaws (Mfd. Since 07/18)
The table is heavy and requires two people
to lift it onto the trunnions. Remove the saw
blade to make table installation easier.
8.
Models G0513 and G0513ANV: Secure the
table to the trunnions, as shown in Figure 24
with the (4) M8-1.25 x 16 hex bolts, 8mm lock
washers, and 8mm flat washers.
Installing Fence (G0513, G0513ANV,
G0513X2 & G0513X2F)
1.
Attach the rear rail to the table with the (2)
M6-1 x 16 cap screws, as shown in Figure 25.
2.
Attach the front rail with the (2) M6-1 x 20 hex
bolts, 6mm lock washers, and 6mm flat washers, as shown in Figure 25.
Rear Rail
Trunnions
x2
x2
x4
Front Rail
Figure 24. Mounting the table.
Models G0513X2, G0513X2B, G0513X2BF,
and G0513X2F: Secure the table to the trunnions with the (4) M8-1.25 x 25 hex bolts,
8mm lock washers, and 8mm flat washers.
9.
Replace the saw blade.
Figure 25. Rail installation.
3.
Install an M8-1.25 hex nut on the fence
handle, then thread the handle into the fence
assembly, as shown in Figure 26. Tighten
the hex nut against the fence pivot block to
secure the handle.
Pivot Block
Hex
Nut
Figure 26. Example of handle installed on fence
assembly.
G0513 Series Bandsaws (Mfd. Since 07/18)
-25-
4.
Pull the fence handle up and place the fence
assembly on the front rail (see Figures
27–28).
Installing Fence (G0513X2B &
G0513X2BF)
1.
Attach the rail plates to the front rail with the
(3) M6-1 x 20 cap screws, 6mm lock washers, and 6mm flat washers (see Figure 29).
Front Rail
Rail Plate
Fence
Assembly
Flat Washer 6mm
Lock Washer 6mm
Cap Screw
M6-1 x 20
Cap Screw
M8-1.25 x 20
Figure 27. Fence assembly installed on G0513
and G0513ANV.
Flat
Washer
8mm
Knob
Lock Washer
8mm
Figure 29. Installing front rail onto table.
2.
Attach the outer two rail plates with the round
and elongated mounting holes to the outer
part of the table bottom with (2) M8-1.25 x 20
knobs and 8mm flat washers.
3.
Attach the remaining rail plate with the round
mounting holes using (1) M8-1.25 x 20 cap
screw, 8mm lock washer, and 8mm flat
washer (see Figure 29).
4.
Thread the fence handle into the fence, then
tighten the hex nut against the fence pivot
block (see Figure 30).
Fence
Assembly
Figure 28. Fence assembly installed on
G0513X2 and G0513X2F.
5.
Push the fence handle down to lock the fence
assembly in place.
6.
Adjust the rear rail pad until there is an even
gap between the bottom of the fence and the
table, then tighten the rail pad hex nut against
the fence.
Fence
Handle
Hex Nut
Figure 30. Fence handle components.
-26-
G0513 Series Bandsaws (Mfd. Since 07/18)
5.
Install the fence on the left-hand side of the
blade.
Installing Resaw Fence (G0513X2,
G0513X2B, G0513X2BF & G0513X2F)
6.
Place the fence flush against the bandsaw
blade (see Figure 31).
1.
Place the 8mm flat washer on the locking
handle (see Figure 33), slide it through the
hole in the fence, then thread the moving
plate onto the end of the locking handle
threads.
2.
Slide the resaw fence over the moving plate,
as shown in Figure 33, so the moving plate
fits inside the channel of the resaw fence,
then tighten the locking handle.
Resaw Fence
Locking
Handle
Figure 31. Fence flush with blade.
7.
Moving
Plate
Loosen the pointer adjustment nut (see
Figure 32) and set the pointer in line with "0"
on the measurement scale on the rail.
Pointer Nut
Pointer
Figure 33. Attaching resaw fence.
Locking Handle
Resaw
Fence
Figure 32. Calibrating fence pointer
(adjustment nut out of view).
8.
Figure 34. Resaw fence properly installed.
Re-tighten the pointer adjustment nut.
G0513 Series Bandsaws (Mfd. Since 07/18)
-27-
Initial Blade Tracking
Serious personal injury can
occur if the machine starts
while your hand is touching the bandsaw wheel during tracking adjustments.
Disconnect power from the
bandsaw before performing blade tracking adjustments.
Blade tracking is primarily affected by the tilt of
the upper wheel, known as “center tracking.”
However, the alignment of both wheels plays an
important part as well (see the Aligning Wheels
instructions on Page 68 for more details).
The wheels on this bandsaw were aligned at the
factory, so center tracking is the only adjustment
that needs to be performed when the saw is
new.
The wheels may have sharp edges and the
blade teeth may extend beyond the edge,
creating a laceration hazard. Be careful
when turning the wheels by hand.
5.
Spin the upper wheel by hand at least three
times and watch how the blade rides on the
crown of the wheel. Refer to Figure 36 for an
illustration of this concept.
—If the blade rides in the center of the upper
wheel and is centered on the peak of the
wheel crown, then the bandsaw is already
tracking properly and no further adjustments are needed at this time.
—If the blade does not ride in the center of
the upper wheel and is not centered on the
peak of the wheel crown, then continue
with the following steps.
To center track the blade:
1.
DISCONNECT BANDSAW FROM POWER!
2.
Make sure the upper and lower blade guides
are adjusted away from the blade.
3.
Open the upper wheel cover.
4.
Engage the quick tension lever, then turn the
blade tension handwheel until the tension
scale (see Figure 35) is between 4 and 6.
Blade Centered
on Peak of Crown
Blade
Centered
on
Wheel
Wheel
Figure 36. Center tracking profiles.
CENTER TRACKING
IMPORTANT
Blade Tension
Scale
Changes made to the blade tension may
change how the blade tracks.
Blade Tension
Handwheel
Figure 35. Blade tensioning controls.
-28-
G0513 Series Bandsaws (Mfd. Since 07/18)
6.
Adjusting Positive
Stop
Loosen the lock lever on the back of the
bandsaw (see Figure 37) so that the blade
tracking knob can rotate.
Blade Tracking
Knob
The positive stop allows the table to be quickly
and accurately returned to the horizontal (0˚) position after being adjusted to a different angle.
To position the positive stop:
1.
DISCONNECT BANDSAW FROM POWER!
2.
Adjust the blade tension until the mark on the
blade tension scale is between 4 and 6.
3.
Loosen the hex nut that locks the positive
stop bolt in place.
4.
Raise the guide post and place a machinist’s
square on the table next to the side of the
blade, as illustrated in Figure 38. Adjust the
table square with the blade, then secure it
with the table tilt lock lever.
Lock Lever
Figure 37. Blade tracking controls.
7.
Spin the upper wheel with one hand and
rotate the tracking control knob in small
amounts with the other hand until the blade
consistently rides in the center of the bandsaw
wheel tire.
8.
Tighten the tracking control lock knob and
close the upper wheel cover.
Note: For the best performance from your saw,
regularly maintain proper tracking of the blade.
Fine tune tracking must be done with the bandsaw
turned ON. This will be explained later in the
Operations section.
Figure 38. Squaring table to blade.
G0513 Series Bandsaws (Mfd. Since 07/18)
5.
Adjust the positive stop bolt against the bottom of the table and secure it by tightening
the hex nut against the trunnion bracket.
6.
Check the adjustment for accuracy once you
have tightened the hex nut.
7.
Loosen the screw on the pointer, but do not
remove it.
8.
Align the tip of the pointer with the 0˚ mark on
the table tilt scale, then re-tighten the screw
to secure the setting.
-29-
Dust Collection
DO NOT operate this bandsaw without an
adequate dust collection system. This saw
creates substantial amounts of wood dust
while operating. Failure to use a dust collection system can result in short and longterm respiratory illness.
Recommended CFM at Dust Port: 400 CFM
Do not confuse this CFM recommendation with
the rating of the dust collector. To determine the
CFM at the dust port, you must consider these
variables: (1) CFM rating of the dust collector,
(2) hose type and length between the dust collector and the machine, (3) number of branches
or wyes, and (4) amount of other open lines
throughout the system. Explaining how to calculate these variables is beyond the scope of
this manual. Consult an expert or purchase a
good dust collection "how-to" book.
-30-
To connect a dust collection hose:
1.
Fit a 4" dust hose over each dust port and
secure them in place with a hose clamp (see
Figure 39).
2.
Tug the hoses to make sure they do not
come off.
Note: A tight fit is necessary for proper performance.
Figure 39. Dust hose attached to bottom dust
port.
G0513 Series Bandsaws (Mfd. Since 07/18)
Power Cord
Connection
(G0513X2BF &
G0513X2F)
3.
Loosen the right strain relief on the junction
box, then feed the cord into the box with
enough slack in the wires to make the connections.
4.
Re-tighten the strain relief around the cord.
Tug on it to make sure the wires inside the
box will not move.
5.
Connect the incoming ground wire to the
ground post, as shown in Figure 41.
Serious injury could occur if you connect
machine to power before completing setup
process. DO NOT connect to power until
instructed later in this manual.
Power Supply Junction Box
Ground
Ground
E
The power cord connection MUST be performed
by an electrician or qualified service personnel.
Items Needed
Qty
Cord “S”-Type, 3-Wire, 14 AWG, 300 VAC,
at least 6 ft. long.......................................... 1
Phillips Screwdriver #2....................................... 1
Wire Nuts for (2) 14 AWG Wires......................... 3
Electrical Tape.................................... As Needed
To connect the power cord to the machine:
1.
2.
Attach the required plug to the cord per
the plug manufacturer's instructions (refer
to Power Supply beginning on Page 11 for
specifications and the NEMA plug wiring on
Pages 74– 75).
R
S
Strain
Relief
To
Bandsaw
From
Power Supply
Figure 41. Incoming power cord connections.
6.
Secure the two incoming hot wires to the
black and white wires from the bandsaw
with wire nuts, then wrap the nuts and wires
with electrical tape to make sure they will not
come loose.
7.
Re-attach the junction box cover.
Remove the power supply junction box cover
from the right rear of the bandsaw (see
Figure 40). It is secured by two screws.
Power Supply
Junction Box
Strain
Relief
Figure 40. Power supply junction box on rear of
bandsaw.
G0513 Series Bandsaws (Mfd. Since 07/18)
-31-
Test Run
Once the assembly is complete, test run your
machine to make sure it runs properly and is
ready for regular operation.
The test run consists of verifying the following: 1)
The motor powers up and runs correctly, and 2)
the safety disabling mechanism works correctly.
If, during the test run, you cannot easily locate
the source of an unusual noise or vibration, stop
using the machine immediately, then review
Troubleshooting on Page 60.
If you still cannot remedy a problem, contact our
Tech Support at (570) 546-9663 for assistance.
To test run the machine:
1.
2.
Make sure that you have successfully completed the Initial Blade Tracking procedure
on Page 28 before continuing.
Make sure you have read the safety instructions at the beginning of the manual and that
the machine is setup properly.
3.
Make sure all tools and objects used during
setup are cleared away from the machine.
4.
Connect the machine to the power source.
5.
Test the operation of the machine to verify
that it starts and operates correctly.
G0513, G0513ANV & G0513X2 Only
a. Verify that the machine is operating correctly by pressing the power button.
— When operating correctly, the
machine runs smoothly with little or
no vibration or rubbing noises.
— Investigate and correct strange or
unusual noises or vibrations before
operating the machine further. Always
disconnect the machine from power
when investigating or correcting
potential problems.
-32-
G0513X2B, G0513X2F, & G0513X2BF Only
a. Insert the key into the power switch (see
Figure 42), then turn it to the "1".
Power Switch
ON Button
OFF Button
Figure 42. G0513X2B and G0513X2BF control
panel.
b. Verify that the machine is operating correctly by pressing the ON button.
— When operating correctly, the
machine runs smoothly with little or
no vibration or rubbing noises.
— Investigate and correct strange or
unusual noises or vibrations before
operating the machine further. Always
disconnect the machine from power
when investigating or correcting
potential problems.
c. Press the OFF button to stop the
bandsaw.
d. WITHOUT resetting the OFF button, press
the ON button. The machine should not
start.
— If the machine does start (with the
OFF button pushed in), immediately
disconnect the machine from power.
The OFF button safety feature is not
working correctly. This safety feature
must work properly before proceeding with regular operations. Call Tech
Support for help.
G0513 Series Bandsaws (Mfd. Since 07/18)
e. Push the OFF button in, then twist it
clockwise so it pops out. When the OFF
button pops out, the switch is reset and
ready for operation (see Figure 43).
Tensioning Blade
A properly tensioned blade is essential for making accurate cuts, maximizing the life of the
blade, and making other bandsaw adjustments.
However, it will not compensate for cutting problems caused by too rapid of a feed rate, hardness
variations between workpieces, and improper
blade selection.
OFF Button
Figure 43. Resetting the OFF button.
f.
Turn the key in the power switch to "0".
g. Try to turn the machine ON. The bandsaw
should not start.
— If the bandsaw starts, immediately
disconnect the machine from power.
The switch disabling feature is not
working correctly. This safety feature
must work properly before proceeding with regular operations. Call Tech
Support for help.
6.
Test the operation of the foot brake:
G0513X2BF & G0513X2F Only
a. Start the bandsaw, then press the foot
brake. The motor should shut off and the
blade should come to a rapid stop.
— If the motor does not stop or the
blade does not come to a rapid stop,
immediately disconnect the machine
from power. The foot brake feature
is not working correctly. This safety
feature must work properly before
proceeding with regular operations.
Call Tech Support for help.
Congratulations! The test run is complete and
you are ready to proceed with the following
adjustments before putting the bandsaw into full
operation.
G0513 Series Bandsaws (Mfd. Since 07/18)
Improper blade tension is unsafe, produces
inaccurate and inconsistent results, and
introduces unnecessary wear on bandsaw
components. Over-tensioning the blade
increases the chance of the blade breaking
or wheel misalignment. Under-tensioned
blades wander excessively while cutting
and will not track properly during operation.
Tensioning the blade according to the blade
tension scale before the Test Run section
gave an approximate tension for completing
the bandsaw setup. The following procedures tension the blade for operation.
Blade tensioning method is a matter of preference.
The flutter method and the deflection method are
described below. Either method safely tensions
the blade. Experience and personal preference
will help you decide which method your prefer.
Optimal cutting results for any workpiece results
from a combination of correct blade selection,
proper blade tension, and a light and even feed
rate.
Flutter Method
1.
DISCONNECT BANDSAW FROM POWER!
2.
Make sure the blade is properly center tracking as instructed in the Initial Blade Tracking
on Page 28.
3.
Raise the guide post all the way, and move
the upper and lower blade guides away from
the blade.
-33-
4. Engage the blade tension quick-release lever
to apply tension to the blade (see Figure 44).
Blade Tension
Quick-release
Lever
Deflection Method
The deflection method is more subjective than the
flutter method. Each blade deflects differently and
every user must determine what "moderate pressure" means. The following are general guidelines for tensioning the blade with the deflection
method.
To tension the bandsaw blade:
1.
DISCONNECT BANDSAW FROM POWER!
2.
Make sure the blade is properly tracking as
instructed in the Initial Blade Tracking section on Page 28.
3.
Raise the guide post all the way, and move
the upper and lower blade guides away from
the blade.
4.
Engage the blade tension quick-release lever
to apply tension to the blade.
5.
Using moderate pressure, push the center of
the blade sideways.
Figure 44. Blade tension quick-release lever
(G0513X2 shown).
5.
Connect the bandsaw to power, and turn the
bandsaw ON.
6.
Using the blade tension handwheel
(Figure 45), slowly decrease blade tension
until the blade starts to flutter.
— If the blade deflects approximately 1⁄4", it is
properly tensioned. Proceed to Step 6.
— If the blade deflects less than 1⁄4" it is
over-tensioned. Turn the blade tensioning
handwheel counterclockwise two full turns
and repeat this step.
Blade Tension
Handwheel
— If the blade deflects more than 1⁄4", the
blade is under-tensioned. Apply tension to
the blade a small amount and repeat this
step until the blade is properly tensioned.
Figure 45. Blade tension handwheel.
7.
Slowly increase the tension until the blade
stops fluttering, then turn the blade tension
adjustment knob an additional 1⁄8 to 1⁄4 of a
turn.
8.
Turn the bandsaw OFF and disconnect it
from power.
9.
Note what the tension gauge reads. Use that
as a guide for tensioning that specific blade
in the future.
10. Re-adjust blade guides as described in
Adjusting Blade Guides beginning on Page
36 for your model bandsaw.
-34-
6.
Re-adjust the blade guides as described in
Adjusting Blade Guides beginning on Page
36 for your model bandsaw.
Whenever changing a blade or adjusting
tension and tracking, the upper and lower
blade support bearings and blade guides
must be properly adjusted before performing cutting operations.
G0513 Series Bandsaws (Mfd. Since 07/18)
Adjusting Blade
Support Bearings
Support bearings stop excessive backward deflection of the blade from the advancing workpiece.
The proper adjustment of the support bearings
is an important part of making accurate cuts and
prevents damage to the blade teeth from contact
with the blade guides.
It is important that the distance of the support
bearing behind the blade is the same as the distance of the blade guides behind the teeth gullets,
which is typically about 0.016" (see Figure 46).
Tools Needed
Qty
Hex Wrench 5mm............................................... 1
Feeler Gauge 0.016".................................. 1 Each
Crisp Dollar Bill (Optional).................................. 1
Tip: You can use a crisp dollar bill in place of the
feeler gauge for the following procedures. The
thickness of the bill when folded in half twice is
approximately 0.016".
Refer to Figures 47–48 and the following descriptions to become familiar with the controls to adjust
the support bearings. Then, adjust the surface of
the support bearings approximately 0.016" behind
the blade.
Note: The support bearing controls are similar for
all models.
0.016"
Gap
A
0.016"
Gap
B
Support
Bearing
Blade
Guide
Figure 46. Distance settings of upper support
bearings and blade guides.
C
Figure 47. Upper support bearing controls.
D
Before adjusting the blade support bearings, make sure the blade is tracking properly (Page 28) and that it is correctly tensioned (Page 33).
A
C
Figure 48. Lower support bearing controls.
G0513 Series Bandsaws (Mfd. Since 07/18)
-35-
A. Support Bearing. Stops excessive backward blade deflection from the pressure of
the advancing workpiece.
Note: The flat surface of the upper support
bearing faces the blade. The round edge of
the lower support bearing faces the blade.
B. Upper Support Bearing Shaft. Mounts the
support bearing behind the blade. When the
support bearing shaft cap screw is loose,
move this shaft by hand to adjust the upper
support bearing approximately 0.016" behind
the blade, then re-tighten the shaft cap screw
to secure the setting.
C. Support Bearing Shaft Cap Screw. When
loose, allows distance adjustment of the support bearing behind the blade.
D. Lower Support Bearing Adjustment Knob.
When the support bearing shaft cap screw is
loose, moves the support bearing toward or
away from the blade. Use this knob to adjust
the lower support bearing approximately
0.016" behind the blade, then re-tighten the
shaft cap screw to secure the setting.
Adjusting Blade
Guides
The blade guides provide side-to-side support
to keep the blade straight while cutting. These
guides are adjustable in two ways—forward-andback and side-to-side.
To keep the blade straight while cutting, the blade
guides must be as close to the sides of the blade
without exerting any clamping pressure. This distance is typically about 0.004".
To prevent damage to the blade teeth as the blade
deflects back while cutting, the guides must be
behind the teeth gullets the same amount as the
support bearing is behind the blade, which is typically about 0.016" (see Figure 46 on the previous
page for an illustration of this relationship).
Note: Models G0513 and G0513ANV use carbide
discs as guides, while the remaining models use
ball bearings.
Before adjusting the blade guides, make
sure the blade is tracking properly (Page 28)
and that it is correctly tensioned (Page 33).
IMPORTANT: Although the function and the distance adjustment of the blade guides is the same
for all the G0513 Series Models, the guide controls are not all the same. Use the set of instructions on the following pages that is correct for your
model of bandsaw.
-36-
G0513 Series Bandsaws (Mfd. Since 07/18)
Adjusting Blade Guides (G0513 &
G0513ANV)
3.
Tools Needed
Qty
Hex Wrench 5mm............................................... 1
1 Each
Feeler Gauge 0.004".................................
0.016"
1
Crisp Dollar Bill (Optional)..................................
Gap
Blade
Fine
Ruler........................................................... 1
By hand, adjust the distance of the guides
approximately 0.004" from the sides of the
blades (see Figure 50), then re-tighten the
thumb screws to secure the setting.
0.004"
Gap
Tip: You can use a crisp dollar bill in place of the
feeler gauge. The thickness of the bill is approximately 0.004" .
Blade
Guides
To adjust the upper blade guides:
1.
2.
Blade
Support
DISCONNECT BANDSAW FROM
POWER!
Bearing
Loosen the thumb screws shown in Figure 49.
Figure 50. Correct gap between guide guides
and blade.
Blade
Guides
4.
Loosen the guide block cap screw shown in
Figure 51.
Blade
Guide
0.016"
Gap
Thumb
Screws
Figure 49. Upper blade guides side-to-side controls.
0.016"
Gap
Support
Bearing
Tooth
Gullet
Guide
Block
Guide Block
Cap Screw
Figure 51. Back of upper blade guides.
Blade
G0513 Series Bandsaws (Mfd. Since 07/18)
-37-
5.
By hand, slide the guide block to position the
blade guides approximately 0.016" behind
the teeth gullets (see Figure 52), then retighten the guide block cap screw to secure
the setting.
Blade
Guide
0.016"
Gap
Adjusting Blade Guide Bearings
(G0513X2, G0513X2B, G0513X2BF, &
G0513X2F)
Tools Needed
Qty
Hex Wrench 5mm............................................... 1
Feeler Gauge 0.004", 0.016"..................... 1 Each
Crisp Dollar Bill (Optional).................................. 1
Tip: You can use a crisp dollar bill in place of the
feeler gauge. The thickness of the bill is approximately 0.004", and when folded in half twice is
approximately 0.016".
Note: The upper and lower guide bearings are
adjusted in the same manner.
Tooth
Gullet
To adjust the upper and lower blade guide
bearings:
Figure 52. Correct guide alignment behind the
teeth gullets.
Make sure that the blade teeth will not contact the guides when the blade is against the
rear support bearing during the cut or the
blade teeth will be damaged.
1.
DISCONNECT BANDSAW FROM POWER!
2.
Familiarize yourself with the blade guide controls shown in Figure 54.
Blade Guide
Bearings
Lateral Rod
Cap Screw
The lower blade guides are adjusted in the same
manner as the upper blade guides. However,
some controls are different. Refer to Figure 53 to
become familiar with these controls.
Knurled
Knob
Bearing Rotation
Cap Screw
Figure 54. Blade guide controls.
Thumb
Screw
Make sure that the blade teeth will not contact the guide bearings when the blade is
against the rear support bearing during the
cut or the blade teeth will be damaged.
Guide
Block
Guide Block
Cap Screw
Figure 53. Lower blade guide controls.
-38-
G0513 Series Bandsaws (Mfd. Since 07/18)
3.
Loosen the lateral rod cap screw and slide
the guide block to position the blade guides
approximately 0.016" behind the blade gullets, as illustrated in Figure 55.
Note: The 0.016" spacing is ideal, although
with larger blades it may not be possible.
In such cases, adjust the guide bearings as
far forward as possible to the blade gullets,
and still maintain the proper support bearing
spacing adjustment.
Blade
Gullet
Aligning Table
To ensure cutting accuracy when the table is first
installed, the table should be aligned so that the
miter slot is parallel to the bandsaw blade. This
procedure works best with a wide (3 ⁄4") blade
installed.
Tools Needed
Qty
Straightedge....................................................... 1
Fine Ruler........................................................... 1
Square................................................................ 1
Wrench or Socket 13mm.................................... 1
To align the table so the miter slot is parallel
to the bandsaw blade:
Guide
Bearings
0.016"
Gap
Figure 55. Lateral adjustment of blade guides.
4.
1.
Make sure that the blade is tracking properly
and that it is correctly tensioned.
2.
DISCONNECT BANDSAW FROM POWER!
3.
Loosen the trunnion bolts that secure the
table.
4.
Place an accurate straightedge along the
blade. The straightedge should lightly touch
both the front and back of the blade.
Tighten the lateral rod cap screw to secure
the setting.
5.
Loosen both bearing rotation cap screws.
6.
Rotate the knurled knob to position the bearings approximately 0.004" away from the
blade.
7.
Re-tighten the cap screws to lock the blade
guide bearings in position.
Note: Make sure the straightedge does not
go across a tooth.
5.
Use a fine ruler to gauge the distance
between the straightedge and the miter slot.
The distance you measure should be the
same at the front and the back of the table
(see Figure 56).
Figure 56. Measuring for miter slot to be parallel
with blade.
G0513 Series Bandsaws (Mfd. Since 07/18)
-39-
—If the distance is not the same at the front
and back of the table, adjust the table until
it is.
6.
4.
Place a square on the table and against the
back of the blade, as shown in Figure 57. The
table should be perpendicular to the back of
the blade.
Loosen the four cap screws located on the
top face of the fence (see Figures 58–59).
G0513 & G0513ANV
Fence Cap Screws
—If the table is not perpendicular to the back
of the blade, shim the table in the desired
direction by placing washers between the
table and the two trunnions.
7.
Re-tighten the trunnion bolts to secure the
settings.
Figure 58. G0513 & G0513ANV fence caps
screws.
Blade
Square
G0513X2F Fence
Cap Screws
Table
Figure 57. Squaring back of blade and table.
Aligning Fence
To ensure cutting accuracy when the fence is first
installed, the fence should be aligned with the
miter slot.
5.
Tool Needed
Qty
Hex Wrench 5mm............................................... 1
Adjust the fence face parallel with the edge of
the miter slot.
6.
Tighten the four cap screws, being careful not
to move the fence.
Figure 59. Four fence cap screws.
Aligning Fence (G0513, G0513ANV,
G0513X2 & G0513X2F)
1.
DISCONNECT BANDSAW FROM POWER!
2.
Make sure the table is aligned with the blade
(see Aligning Table on the previous page for
detailed instructions).
3.
Install the fence next to the miter slot.
-40-
G0513 Series Bandsaws (Mfd. Since 07/18)
1.
DISCONNECT BANDSAW FROM POWER!
Calibrating Miter
Gauge
2.
Make sure the table is aligned with the blade
(see Aligning Table on Page 39 for detailed
instructions).
The miter gauge needs to be calibrated to the
blade when it is first mounted in the miter slot.
3.
Install the fence and lock it in place next to
the miter slot.
Tool Needed
Qty
Phillips Screwdriver #2....................................... 1
4.
Loosen the end knobs and the center cap
screw that secure the front rail to the table
(see Figure 60).
To calibrate the miter gauge:
Aligning Fence (G0513X2B &
G0513X2BF)
1.
DISCONNECT BANDSAW FROM POWER!
2.
Use a square with one edge against the face
of the miter gauge and the other against the
blade side, as shown in Figure 62.
Loosen These
Figure 60. Loosen these knobs and cap screw.
5.
Adjust the fence face parallel with the edge of
the miter slot, as shown in Figure 61.
Figure 62. Squaring miter gauge to blade.
3.
Loosen the lock knob on the miter gauge
and adjust the face flush with the edge of the
square.
4.
Tighten the lock knob, and verify the setting.
Note: Sometimes the tightening procedure
can affect the adjustment.
Figure 61. Example of fence parallel with miter
slot.
6.
Tighten the knobs and cap screw that secure
the rail to the table, being careful not to move
the fence.
G0513 Series Bandsaws (Mfd. Since 07/18)
5.
Loosen the screw that secures the angle
pointer, and adjust the pointer to the 0˚ mark
on the scale.
6.
Re-tighten the screw to secure the setting.
-41-
SECTION 4: OPERATIONS
Operation Overview
The purpose of this overview is to provide the novice machine operator with a basic understanding
of how the machine is used during operation, so
the machine controls/components discussed later
in this manual are easier to understand.
Due to the generic nature of this overview, it is
not intended to be an instructional guide. To learn
more about specific operations, read this entire
manual, seek additional training from experienced
machine operators, and do additional research
outside of this manual by reading "how-to" books,
trade magazines, or websites.
To reduce your risk of
serious injury, read this
entire manual BEFORE
using machine.
To complete a typical operation, the operator
does the following:
1.
Examines the workpiece to make sure it is
suitable for cutting.
2.
Adjusts the fence away from the blade the
same width of the desired cut or out of the
way for curve cutting and then locks it in
place.
3.
Adjusts the table tilt, if necessary, to the correct angle of the desired cut.
4.
Adjusts the blade guide height to not more
than 1" from the top of the workpiece.
5.
Checks to make sure the workpiece can safely pass all the way through the blade without
interference from other objects.
6.
Puts on safety glasses.
7.
Starts the dust collector and bandsaw.
8.
Holds the workpiece firmly and flatly against
both the table and fence, and then pushes
the workpiece into the blade at a steady and
controlled rate until the workpiece moves
completely beyond the blade.
To reduce risk of eye injury from flying
chips or lung damage from breathing dust,
always wear safety glasses and a respirator
when operating this machine.
The operator is very careful to keep fingers
away from the blade and uses a push stick to
feed narrow workpieces.
9.
Stops the bandsaw.
If you are not experienced with this type
of machine, WE STRONGLY RECOMMEND
that you seek additional training outside of
this manual. Read books/magazines or get
formal training before beginning any projects. Regardless of the content in this section, Grizzly Industrial will not be held liable
for accidents caused by lack of training.
-42-
G0513 Series Bandsaws (Mfd. Since 07/18)
Disabling & Locking
Switch (G0513,
G0513ANV, G0513X2)
The switch can be disabled and locked by inserting a padlock through the power button, as
shown in Figure 63. Locking the switch in this
manner can prevent unauthorized operation of
the machine, which is especially important if the
machine is not stored inside an access-restricted
building.
IMPORTANT: Locking the switch with a padlock
only restricts its function. It is not a substitute
for disconnecting power from the machine when
adjusting or servicing.
Disabling & Locking
Switch (G0513X2B,
G0513X2BF,
G0513X2F)
The power switch can be disabled and locked by
removing the key, as shown. Locking the switch
in this manner can prevent unauthorized operation of the machine, which is especially important
if the machine is not stored inside an accessrestricted building.
IMPORTANT: Locking the power switch with a
key only restricts its function. It is not a substitute
for disconnecting power from the machine when
adjusting or servicing.
Padlock
Shaft
PO
0 WER
I
Figure 63. Switch disabled by a padlock.
The padlock shaft diameter is important to
the disabling function of the switch. With
any padlock used to lock the switch, test the
switch after installation to ensure that it is
properly disabled.
G0513 Series Bandsaws (Mfd. Since 07/18)
Children or untrained people can be killed
or seriously injured by this machine. This
risk increases with unsupervised operation.
To help prevent unsupervised operation,
remove the key from the switch before
leaving machine unattended! Place key in a
well-hidden or secure location.
-43-
General Overview
The bandsaw is one of the most versatile wood
cutting tools in the shop. It is capable of performing many different cutting functions including:
Straight Cuts
•
•
•
•
•
•
Miters
Angles
Compound Angles
Resawing
Ripping
Crosscutting
Workpiece
Inspection
Some wood workpieces are not safe to cut or may
require modification before they are safe to cut.
Before cutting wood, get in the habit of
inspecting all workpieces for the following:
•
Material Type: This machine is intended for
cutting natural and man-made wood products,
and laminate covered wood products. Cutting
drywall or cementitious backer board creates
extremely fine dust, which may reduce the
life of the bearings. This machine is NOT
designed to cut metal, glass, stone, tile, etc.
•
Foreign Objects: Nails, staples, dirt, rocks
and other foreign objects are often embedded in wood. While cutting, these objects can
become dislodged and hit the operator or
break the blade, which might then fly apart.
Always visually inspect your workpiece for
these items. If they can't be removed, do
NOT cut the workpiece.
•
Large/Loose Knots: Loose knots can
become dislodged during the cutting operation. Large knots can cause blade damage.
Choose workpieces that do not have large/
loose knots or plan ahead to avoid cutting
through them.
•
Wet or "Green" Stock: Cutting wood with
a moisture content over 20% causes unnecessary wear on the blade and yields poor
results.
•
Excessive Warping: Workpieces with excessive cupping, bowing, or twisting are dangerous to cut because they are unstable and can
move unpredictably when being cut. DO NOT
cut excessively warped wood.
•
Minor Warping: Workpieces with slight cupping can be safely supported if the cupped
side faces the table or fence. On the contrary,
a workpiece supported on the bowed side will
rock during a cut, leading to loss of control.
Irregular Cuts
•
•
•
•
Simple and Complex Curves
Duplicate Parts
Circles
Beveled Curves
A properly adjusted and tuned bandsaw can be
safer to operate than most other saws and performs many functions with ease and accuracy.
Basic Cutting Tips
Here are some basic tips to follow when operating the bandsaw:
•
Replace, sharpen, and clean blades as necessary and make adjustments periodically to
keep the saw always running in top condition.
•
Use a light and even feed rate while cutting.
Light contact with the blade will permit easier
line following and prevent undue friction.
•
Avoid trying to turn tight corners because this
will twist the blade. Remember, you must saw
around corners.
•
Misuse of the saw or using incorrect techniques is unsafe and results in frustration and
poor cuts. Remember—the blade does the
cutting with the operator’s guidance.
-44-
G0513 Series Bandsaws (Mfd. Since 07/18)
Table Tilt
Models G0513X2, G0513X2B,
G0513X2BF & G0513X2F
Model
Tilt Specifications
G0513, G0513ANV.................... 10° left, 45° right
G0513X2...................................... 5° left, 45° right
G0513X2B................................... 5° left, 45° right
G0513X2BF................................. 5° left, 45° right
G0513X2F.................................... 5° left, 45° right
Angle Indicator Scale
Table Tilt
Lever
Remove the positive stop bolt to tilt the table to the
left (as viewed from the front).
Refer to Figures 64–65 to familiarize yourself
with the table tilt controls for your model bandsaw.
Lock Lever
Figure 65. Table tilt controls
(G0513X2, G0513X2B, G0513X2BF, and
G0513X2F rear view).
Models G0513 & G0513ANV
Angle Indicator Scale
Located On Opposite Face
To tilt the table:
1.
DISCONNECT BANDSAW FROM POWER!
2.
Loosen the lock lever to enable table movement.
3.
Use the table tilt knob/lever to adjust the
angle of the table as displayed on the angle
indicator scale.
4.
Secure the table with the lock lever before
continuing operation.
Lock
Lever
Table Tilt Knob
Figure 64. Table tilt controls
(G0513 and G0513ANV rear view).
G0513 Series Bandsaws (Mfd. Since 07/18)
-45-
Guide Post
Fine Tune Tracking
The guide post connects the upper blade guide
assembly to the bandsaw. The guide post allows
the blade guide assembly to move up or down so
that it is as close to the workpiece as possible for
safety and blade support.
During setup, the blade was tracked without the
machine connected to power. In this procedure,
the bandsaw is turned ON to perform fine tuning of the tracking. Make small changes with the
blade tracking knob as you monitor the effect on
the blade tracking.
In order to cut accurately and safely, the bottom of
the blade guide assembly must be no more than
1" above the workpiece at all times—this positioning provides the greatest blade support and
minimizes the amount of moving blade exposed
to the operator.
To adjust the blade guide assembly on the
guide post:
1.
DISCONNECT BANDSAW FROM POWER!
2.
Make sure that the blade tension, blade tracking, support bearings, and blade guides are
adjusted correctly, as previously described in
the SETUP section.
3.
Loosen the guide post lock knob shown in
Figure 66.
Guide Post
Handwheel
To fine tune the tracking:
1.
Close the wheel covers and turn the bandsaw
ON.
2.
Observe the blade tracking path through
the clear window on the right edge of the
bandsaw, as shown in Figure 67.
Guide Post
Lock Knob
Figure 67. Blade tracking window.
Blade Guard
3.
Using the tracking controls, adjust the blade
so it tracks on the center of the wheel.
4.
Tighten the tracking lock to secure the setting.
Guide Post
Blade Guide
Assembly
Figure 66. Guide post controls.
4.
Turn the guide post handwheel to adjust the
upper blade guide assembly to within 1" from
the top of the workpiece.
5.
Lock the guide post in place with the lock
knob.
-46-
G0513 Series Bandsaws (Mfd. Since 07/18)
Blade Selection
Selecting the right blade for the cutting task
requires knowledge about blade characteristics
and cutting priorities (i.e. speed, finish, etc.).
Blade Terminology
B
C
D
G
I
Figure 68. Bandsaw blade components.
A. Kerf: The amount of material removed by the
blade during cutting.
B. Tooth Set: The amount each tooth is bent
left or right along the blade.
C. Gauge: The thickness of the blade.
D. Blade Width: The widest point of the blade
measured from the tip of the tooth to the back
edge of the blade.
E.
Tooth Rake: The angle of the tooth face
from a line perpendicular to the length of the
blade.
F.
Gullet Depth: The distance from the tooth tip
to the bottom of the curved area (gullet).
G. Tooth Pitch: The distance between tooth
tips.
H. Blade Back: The distance between the bottom of the gullet and the back edge of the
blade.
I.
Blade Width
Blade Material
H
F
Measured by the blade circumference, blade
lengths are specific to each bandsaw. They are
determined by the wheel diameter and distance
between the wheels.
Measured from the back of the blade to the tip
of the blade tooth (the widest point), blade width
is often the first consideration given to blade
selection. Blade width determines the largest and
smallest curve that can be cut, and contributes
to the accuracy of cutting straight—generally the
wider the blade, the straighter it will cut.
A
E
Blade Length
Bandsaw blades must meet two requirements:
flexibility and hardness. The flexibility of a blade
allows it to travel on the wheel as a band, while
hardness allows the teeth to cut and hold an
edge. Modern materials technology has allowed
bandsaw blades to meet these requirements in
various ways.
Carbon Steel: These blades are differentially
heat treated to provide hard teeth that will hold an
edge, and yet be flexible in the back.
Carbide Tooth: Extremely hard carbide is either
welded onto or impregnated into the carbon steel
blades, providing superior edge-holding characteristics (see Figure 69).
Carbon Steel
Carbide Impregnated Steel
Figure 69. Carbide-tooth blade composition.
TPI: The number of teeth per inch measured
from gullet to gullet.
G0513 Series Bandsaws (Mfd. Since 07/18)
-47-
Bimetal Blade: A strip of high-speed tool steel is
precision welded to a flexible carbon blade, then
teeth are ground into the blade to provide good
edge-holding qualities for blades taking a lot of
abuse (see Figure 70).
Carbon Steel Blade
Alternate: An all-purpose arrangement where the
teeth are bent evenly left and right of the blade.
Raker: Three teeth in a recurring group—one
bent left, one bent right, and then one that is not
bent. The raker set is ideal for most contour cuts.
Tooth Type
The most common tooth types for wood blades
are shown and described below (see Figure 72).
Standard (or Raker)
Weld
High-Speed Steel
Figure 70. Bimetal blade composition.
Hook (or Claw)
Tooth Set
Two common tooth sets for wood bandsaw blades
are alternate and raker. Each different type of
tooth set removes material in a different manner,
leaving cuts with different characteristics (see
Figure 71).
Skip (or Skip Tooth)
Figure 72. Typical tooth types.
Alternate
Raker
Figure 71. Common woodcutting bandsaw blade
tooth sets.
-48-
G0513 Series Bandsaws (Mfd. Since 07/18)
Blade Selection Chart
Use the blade selection chart below as a general guide when selecting a blade for your operation.
Cutting Operation
Blade Width
Medium (3 ⁄ 16"– 1 ⁄ 2")
Narrow ( ⁄ 8" – ⁄4")
1
1
Wide (1 ⁄ 2"– 3 ⁄4")
H C
Resawing
H M
R
H
H C
R
H
S
R M
R
H
S
R F
S
HS
R M
S
H
R F M
S
H
R F M
S
Ripping Thin Stock
H
Ripping Thick Stock
R M
Ripping Round Stock
Crosscutting Thin Stock
S
H
Crosscutting Thick Stock
R F M
Crosscutting Round Stock
H
Mitre Cut
H
S
H
Tenons
R M
R
R F
H
Sharp Curves
S
R M
S
S F M
Gradual Curves
S
H
S
R
Tooth Type
Key
Tooth Pitch (Teeth per Inch or TPI)
H
R
S
F
M
C
Hook
Raker
Skip
R
S
Fine
(14-32 TPI)
Medium
(4-12 TPI)
Coarse
(2-4 TPI)
S
G0513 Series Bandsaws (Mfd. Since 07/18)
-49-
Blade Breakage
Many conditions may cause a bandsaw blade to
break. Blade breakage is unavoidable in some
cases, since it is the natural result of the peculiar
stresses that bandsaw blades must endure.
Blade breakage is also due to avoidable circumstances. Avoidable blade breakage is most often
the result of poor care or judgement on the part
of the operator when mounting or adjusting the
blade or support guides.
The most common causes of blade breakage
are:
•
Faulty alignment or adjustment of the blade
guides.
•
Forcing or twisting a wide blade around a
short radius.
•
Feeding the workpiece too fast.
•
Dull or damaged teeth.
•
Over-tensioned blade.
•
Top blade guide assembly set too high above
the workpiece. Adjust the top blade guide
assembly so that there is approximately
1
⁄8"– 1⁄4" between the bottom of the assembly
and the workpiece.
Blade Care &
Break-In
Blade Care
A bandsaw blade is a thin piece of steel that is
subjected to tremendous strain. You can obtain
longer use from a bandsaw blade if you give it fair
treatment and always use the appropriate feed
rate for your operation.
Be sure to select blades with the proper width,
set, type, and pitch for each application. Using the
wrong blade will produce unnecessary heat and
shorten the life of the blade.
A clean blade will perform much better than a dirty
blade. Dirty or gummed up blades pass through
the cutting material with much more resistance
than clean blades. This extra resistance also
causes unnecessary heat.
Blade Break-In
The sharp teeth tips and edges of a new blade are
extremely sharp, and cutting at too fast of a feed
rate fractures the beveled edges of the teeth and
causes premature blade wear.
To properly break-in a new blade:
1.
Choose the correct speed for the blade and
material of the operation.
•
Using a blade with a lumpy or improperly finished braze or weld.
2.
Reduce the feed pressure by half for the first
50–100 in2 of material cut.
•
Continuously running the bandsaw when not
in use.
3.
•
Leaving the blade tensioned when not in
use.
To avoid twisting the blade when cutting,
adjust the feed pressure when the total width
of the blade is in the cut.
•
Using the wrong pitch (TPI) for the workpiece
thickness. The general rule of thumb is to
have not less than two teeth in contact with
the workpiece at all times during cutting.
-50-
G0513 Series Bandsaws (Mfd. Since 07/18)
Blade Changes
Blade changes entail removing the existing blade
from the wheel and table, installing the new blade,
then properly adjusting the blade tension and
tracking.
Installing Blade
1.
DISCONNECT BANDSAW FROM POWER!
2.
Slide the blade through the table slot, ensuring that the teeth are pointing down toward
the table.
Note: If the teeth will not point downward
in any orientation, the blade is inside-out.
Remove the blade, and twist it right side-out.
Removing Blade
1.
DISCONNECT BANDSAW FROM POWER!
2.
Release the blade tension by turning the
blade tension quick-release lever to the left
(see Figure 73).
3.
Slip the blade through the blade guides, and
mount it on the upper and lower wheels (see
Figure 74).
Move This Lever
to the Left
Blade
Guides
Table Pin
Table
Insert
Figure 74. Placing blade on the wheels.
Figure 73. Blade changing controls
(G0513X2 shown).
All saw blades are dangerous and may cause personal injury. To reduce the
risk of being injured, wear
heavy leather gloves when
handling saw blades.
3.
Remove the table insert and the table pin.
Adjust the upper and lower guide bearings as
far away as possible from the blade.
4.
Open the upper and lower wheel covers, and
with gloved hands, slide the blade off of both
wheels.
5.
Rotate the blade 90˚ and slide it through the
slot in the table to remove it.
G0513 Series Bandsaws (Mfd. Since 07/18)
4.
Tighten the blade tension lever.
5.
Adjust the blade tension (refer to Page 33)
and blade tracking (refer to Page 46).
6.
Adjust the upper/lower guide bearings and
the support bearings (refer to instructions
beginning on Page 35).
7.
Close the wheel covers.
8.
Replace the table insert and table pin.
-51-
Blade Speed
3.
Refer to Figure 76 to locate the correct V-belt
position for the desired blade speed and
move the V-belt to the indicated pulleys.
The blade speed can be adjusted to 1700 or 3500
FPM. Speed adjustments are made by moving the
V-belt position on the motor and wheel pulleys.
BANDSAW
WHEEL
Most woodcutting can be performed successfully
at the higher blade speeds. Slower blade speeds
generally produce better results when cutting
hardwoods, intricate curves, or when an exceptionally smooth cut is desired.
1700 FPM
Use the chart below as a general guide to
blade speed:
Type of Cutting Operation
MOTOR
WHEEL
Blade Speed
(FPM)
Most Species of Wood
3500
Super Dense Hardwood
1700
Fast/Average Feed Rate
3500
Requires Slow Feed Rate
1700
Rough Edges Acceptable
3500
Requires Smooth Edges
1700
Quick, Production Cuts
3500
Detailed, Intricate Cuts
1700
To adjust the blade speed:
1.
DISCONNECT BANDSAW FROM POWER!
2.
Loosen the motor mount cap screws shown
in Figure 75, and rotate the motor to loosen
the V-belt.
3500 FPM
Figure 76. V-belt speeds.
4.
Rotate the motor to tension the V-belt, then
tighten the motor mount cap screws.
5.
Check the V-belt tension by applying moderate pressure between the pulleys (see
Figure 77). If deflection is not approximately
3
⁄4", re-tension the V-belt until it is.
⁄4"
Deflection
3
Bandsaw
Wheel
Motor
Wheel
Figure 77. V-belt deflection.
Figure 75. Motor mount cap screws.
-52-
G0513 Series Bandsaws (Mfd. Since 07/18)
Crosscutting
Resawing
Crosscutting is the process of cutting across the
grain of wood. For plywood and other processed
wood, crosscutting simply means cutting across
the width of the material.
Resawing (see Figure 79 for an example) is the
process of cutting a board into two or more thinner
boards. The maximum board width that can be
resawn is limited by the maximum cutting height
of the bandsaw.
To make a 90˚ crosscut:
1.
Mark the workpiece on the edge where you
want to begin the cut.
2.
Adjust the blade guide assembly to no more
than 1" above the workpiece and the miter
gauge to 90°.
3.
Move the fence out of the way. Place the
workpiece evenly against the miter gauge.
4.
Hold the workpiece against the miter gauge
and line up the mark with the blade.
5.
After all safety precautions have been met,
turn the bandsaw ON. Slowly feed the
workpiece into the blade and continue the
cut until the blade is all the way through the
workpiece. Figure 78 shows a typical crosscutting operation.
Blade selection is one of the most important considerations when resawing. Generally, the wider
blade, the better. In most applications, a hook or
a skip tooth style blade with fewer teeth-per-inch
(from 2 to 4) is desirable because they offer larger
gullet capacities for clearing sawdust, decrease
blade heat, and reduce strain on the motor.
Figure 79. Example of resawing.
When resawing thin pieces, a wandering
blade (blade lead) can tear through the surface of the workpiece, exposing your hands
to the blade teeth. Always use push blocks
when resawing and keep your hands clear
of the blade.
Figure 78. Example of crosscutting.
G0513 Series Bandsaws (Mfd. Since 07/18)
-53-
To resaw a workpiece:
1.
2.
Verify that the bandsaw is setup properly and
that the table is perpendicular to the blade.
Use the widest blade your bandsaw will
accept.
Note: The blade must also be sharp and
clean.
3.
Install the resaw fence, set it to the desired
width of cut, and lock it in place.
Note: When resawing thin workpieces, set up
the resaw fence in the alternate position, as
shown in Figure 80, and make sure to use a
push stick.
Cutting Curves
When cutting curves, simultaneously feed and
turn the stock carefully so that the blade follows
the layout line without twisting. If a curve is so
abrupt that it is necessary to repeatedly back up
and cut a new kerf, use either a narrower blade
or a blade with more TPI (teeth per inch), or make
more relief cuts.
Always make short cuts first, then proceed to
the longer cuts. Relief cuts will also reduce the
chance that the blade will be pinched or twisted.
Relief cuts are cuts made through the waste
portion of the workpiece and are stopped at the
layout line. As you cut along the layout line, waste
wood is released from the workpiece, alleviating
any pressure on the back of the blade. Relief cuts
also make backing the workpiece out easier, if
needed.
NOTICE
The list below displays blade widths and
the corresponding minimum radii for those
blade widths.
Figure 80. Resaw fence installed in the alternate
position.
The fence scale will NOT be accurate when
using the resaw fence.
4.
Support the ends of the board if necessary.
5.
Turn the bandsaw ON.
6.
Using push paddles and a push stick, keep
pressure against the fence and table, and
slowly feed the workpiece into the moving
blade until the blade is completely through
the workpiece.
-54-
Width
Radius
1
⁄8"..................................... 1⁄8"
3
⁄16".................................... 3⁄8"
1
⁄4''..................................... 5⁄8''
3
⁄8''..................................... 11⁄4''
1
⁄2''..................................... 21⁄2''
5
⁄8''..................................... 33⁄4''
3
⁄4''..................................... 51⁄2''
G0513 Series Bandsaws (Mfd. Since 07/18)
Stacked Cuts
One of the benefits of a bandsaw is its ability to
cut multiple copies of a particular shape by stacking a number of workpieces together. Before making stacked cuts, ensure that both the table and
the blade are properly adjusted to 90°. Otherwise,
any error will be compounded.
4.
Make relief cuts perpendicular to the outline of your intended shape in areas where
changes in blade direction could strain the
woodgrain or cause the blade kerf to bind.
5.
Cut the stack of pieces as though you were
cutting a single piece. Follow your layout line
with the blade kerf on the waste side of your
line, as shown in Figure 81.
To complete a stacked cut:
1.
Align your pieces from top to bottom to
ensure that each piece has adequate scrap
to provide a clean, unhampered cut.
2.
Secure all the pieces together in a manner
that will not interfere with the cutting. Hot
glue on the edges works well, as do brad
nails through the waste portion. (Be careful
not to cut into the brads or you may break the
blade!)
3.
On the face of the top piece, lay out the
shape you intend to cut.
G0513 Series Bandsaws (Mfd. Since 07/18)
Figure 81. Example of stack cutting.
-55-
ACCESSORIES
SECTION 5: ACCESSORIES
Installing unapproved accessories may
cause machine to malfunction, resulting in
serious personal injury or machine damage.
To reduce this risk, only install accessories
recommended for this machine by Grizzly.
D2057A—Heavy-Duty SHOP FOX® Mobile Base
This patented base is the most stable on the market with outrigger type supports. Adjusts from 20"
x 201⁄2" to 291⁄2" x 291⁄2". 700 lb. capacity. Weighs
47 lbs.
NOTICE
Refer to our website or latest catalog for
additional recommended accessories.
1311 ⁄ 2" Carbon Steel Replacement Blades
Model
Width
TPI
Type
Gauge
⁄ 8"
14
Raker
0.025
H4803
1
H4804
1
⁄4"
6
Hook
0.025
H4805
1
⁄4"
18
Raker
0.025
H4806
3
⁄ 8"
10
Raker
0.025
H4807
1
⁄ 2"
6
Hook
0.025
H4808
1
⁄ 2"
10
Raker
0.025
H4809
3
⁄4"
3
Hook
0.032
H4810
1"
6
Hook
0.035
H4811
1"
2
Hook
0.035
Figure 82. D2057A SHOP FOX® Mobile Base.
T26544—LED Light w/Mag Base & Flex Arm
This high intensity LED flashlight is ultra-bright
and zoomable, allowing you to focus or disperse
the light. Has three modes: high beam, low beam,
and an emergency flash. Fish eye lens is 1x2000
zoom. Also features a powerful 30 lb. magnetic
base, so you can attach this wherever you need
light. Base has a 9" flexible clamp arm for additional mobility. Includes the LED light, base, plate,
and 3 AAA batteries.
1311 ⁄ 2" Timber Wolf Carbon Steel Blades
Model
Width
TPI
Type
Gauge
⁄ 8"
14
HP
0.025
H8591
1
H8592
1
⁄4"
4
Pos. Claw
0.025
H8593
1
⁄4"
10
Raker
0.025
H8594
3
⁄ 8"
4
Pos. Claw
0.025
H8595
3
⁄ 8"
10
Raker
0.025
H8596
1
⁄ 2"
3
Pos. Claw
0.025
H8597
1
⁄ 2"
10
Raker
0.025
H8598
3
⁄4"
3
Thin
0.025
H8599
1"
3
Pos. Claw
0.035
Figure 83. T26544 LED Light with Base and
Flexible Arm.
order online at www.grizzly.com or call 1-800-523-4777
-56-
G0513 Series Bandsaws (Mfd. Since 07/18)
T26403—The Missing Shop Manual: Bandsaw
Dedicated to providing integral information about
woodworking tools and techniques that other
manuals overlook, the books in this series contain
safety facts, explanations about basic project set
up, and tips for maximizing tool performance. In
Bandsaw, you will find out how to best utilize this
essential workshop tool, and how to get the most
for your money by getting the most from your
equipment. Filled with clear diagrams and instructions, this pocket sized durable manual is ideal for
quick reference in the workshop. 112 pages, soft
cover.
Basic Eye Protection
T20501—Face Shield Crown Protector 4"
T20502—Face Shield Crown Protector 7"
T20503—Face Shield Window
T20451—“Kirova” Clear Safety Glasses
T20452—“Kirova” Anti-Reflective S. Glasses
T20456—DAKURA Safety Glasses, Black/Clear
T20502
T20452
T20503
T20451
T20456
Figure 86. Assortment of basic eye protection.
Figure 84. The Missing Shop Manual: Bandsaw.
Recommended Metal Protectants
G5562—SLIPIT® 1 Qt. Gel
G5563—SLIPIT® 12 Oz. Spray
G2871—Boeshield® T-9 12 Oz. Spray
G2870—Boeshield ® T-9 4 Oz. Spray
H3788—G96 ® Gun Treatment 12 Oz. Spray
H3789—G96® Gun Treatment 4.5 Oz. Spray
D2272—Tilting Roller Stand
Adjusts from 26" to 44", 0º-45º. 150 lb. capacity.
D2273—Single Roller Stand
Adjusts from 26 5⁄8" to 45". 250 lb. capacity.
D2274—5 Roller Stand
Adjusts from 26" to 445⁄8". 250 lb. capacity.
These super heavy-duty roller stands feature convenient hand knobs for fast height adjustment.
D2272
D2274
D2273
Figure 85. Recommended products for protecting unpainted cast iron/steel part on machinery.
Figure 87. SHOP FOX® Roller Stands.
order online at www.grizzly.com or call 1-800-523-4777
G0513 Series Bandsaws (Mfd. Since 07/18)
-57-
SECTION 6: MAINTENANCE
To reduce risk of shock or
accidental startup, always
disconnect machine from
power before adjustments,
maintenance, or service.
Schedule
For optimum performance from your machine,
follow this maintenance schedule and refer to any
specific instructions given in this section.
Daily Check:
•
Loose mounting bolts.
•
Worn or damaged saw blade.
Worn or damaged wires.
•
•
Check/clean wheel brush.
•
Clean/protect table surface.
•
Check lubrication points.
•
Any other unsafe condition.
Monthly Check:
•
V-belt tension, damage, or wear.
•
Clean/vacuum dust build-up from inside cabinet and off motor.
Wheel Brush
The bandsaw is equipped with a lower wheel
brush to keep saw dust from building up on the
tire. The brush should be checked daily and
cleaned when it becomes dirty.
There is an adjustment bracket that allows the
brush to be adjusted for bristle wear (refer to
Adjusting Wheel Brush on Page 65 for detailed
instructions).
-58-
Cleaning &
Protecting
Cleaning the bandsaw is relatively easy. Vacuum
excess wood chips and sawdust, and wipe off the
remaining dust with a dry cloth. If any resin has
built up, use a resin dissolving cleaner to remove
it.
Protect the unpainted cast iron surfaces on the
table by wiping it clean after every use—this
ensures moisture from wood dust does not remain
on bare metal surfaces. Keep the table rust-free
with regular applications of products like G96®
Gun Treatment, SLIPIT®, or Boeshield ® T-9 (see
Page 57 for more details).
Lubrication
An essential part of lubrication is cleaning the
components before lubricating them. This step
is critical because dust and chips build up on
lubricated components, which makes them hard
to move. Simply adding more grease to builtup grime will not result in smooth moving parts.
Clean the components in this section with an oil/
grease solvent cleaner or mineral spirits before
applying lubrication.
All bearings are sealed and permanently lubricated. Leave them alone until they need to be
replaced.
Blade Post Rack
Lubrication Type......... GL2 Grease or Equivalent
Amount..................................................Thin Coat
Frequency........................................... As Needed
To lubricate the blade post rack and pinion:
1.
DISCONNECT BANDSAW FROM POWER!
2.
Lower blade guides until they reach the table.
G0513 Series Bandsaws (Mfd. Since 07/18)
3.
Using a rag and mineral spirits, wipe off any
existing grease and sawdust build-up on the
rack (see Figure 88).
4.
Apply a thin coat of lubricant to the tension
adjustment assembly and tension lever cam
(see Figure 89).
Cam
Adjustment
Assembly
Rack Exposed
for Lubrication
Figure 88. Example of rack lubrication location.
4.
Apply a thin coat of lubricant to the rack.
5.
Move the blade post up and down several
times to distribute the lubricant, then remove
any excess grease to help reduce potential
sawdust build-up.
Tension Adjustment Assembly
Lubrication Type......... GL2 Grease or Equivalent
Amount..................................................Thin Coat
Frequency........................................... As Needed
Figure 89. Example of tension adjustment
assembly locations (top wheel removed for
clarity).
Trunnions
Models G0513 and G0513ANV have steel trunnions that can be cleaned and lubricated with GL2
grease or equivalent along the sliding surfaces
(see Figure 90) when necessary.
Sliding Surfaces
To lubricate the tension adjustment assembly:
1.
DISCONNECT BANDSAW FROM POWER!
2.
Open the top wheel cover and look through
the top of the wheel.
3.
Using a rag and mineral spirits, wipe off any
existing grease and sawdust build-up on the
blade tension adjustment assembly and tension lever cam.
G0513 Series Bandsaws (Mfd. Since 07/18)
Figure 90. Trunnion lubrication location
(G0513 & G0513ANV only).
Models G0513X2, G0513X2B, G0513X2BF, and
G0513X2F have cast iron trunnions that produce
a fine graphite powder over time that acts as a
lubricant. We recommend not adding lubricant
to the trunnions which could make a sticky substance that would prevent smooth movement.
-59-
SECTION 7: SERVICE
Review the troubleshooting procedures in this section if a problem develops with your machine. If you need
replacement parts or additional help with a procedure, call our Technical Support. Note: Please gather the
serial number and manufacture date of your machine before calling.
Troubleshooting
Symptom
Possible Cause
Possible Solution
Machine does not
start or a breaker
trips.
1.
2.
3.
4.
1.
2.
3.
4.
Stop button engaged/at fault.
Switch disabling key removed.
Overload relay in magnetic switch tripped.
Wiring break or short; loose connections.
5. Plug or receptacle is corroded or miswired.
6. Power supply off/incorrect voltage.
7. Motor connection wired incorrectly.
8. Contactor has poor contacts or is at fault.
9. Blown fuse/tripped circuit breaker.
10. Power switch at fault.
11. Start capacitor has blown.
12. Centrifugal switch at fault.
13. Motor at fault.
Machine has
excessive vibration
or noise.
-60-
Reset/replace button.
Re-install switch disabling key.
Allow relay to cool. If necessary, reset.
Replace broken wires; fix shorts or loose
connections.
5. Correct the wiring.
6. Switch power supply on/verify voltage.
7. Wire motor correctly. Refer to diagram inside junction
box or the wiring diagrams beginning on Page 71.
8. Fix contacts or replace.
9. Replace fuse or reset circuit breaker. If problem is
not due to circuit overload, find/repair short.
10. Replace switch.
11. Test/replace if at fault.
12. Adjust/replace centrifugal switch.
13. Repair or replace.
V-belt tension incorrect.
1. Re-tension V-belt (Page 63).
Bent or dull blade.
2. Replace blade (Page 51).
Loose blade.
3. Re-tension blade (Page 33).
Blade weld contacting support bearing or 4. File/stone the blade weld smooth or round back of
blade guides.
blade.
5. Loose machine component.
5. Tighten loose component.
6. Machine incorrectly mounted on floor.
6. Level/shim base; tighten/adjust mounting hardware.
7. Motor fan rubbing on fan cover.
7. Adjust/replace fan cover; replace fan if loose or
damaged.
8. V-belt worn or damaged.
8. Replace V-belt (Page 63).
9. Wheels not coplanar.
9. Adjust wheels coplanar (Page 68).
10. V-belt has a high spot.
10. Replace/adjust the V-belt (Page 63).
11. Pulleys loose or not aligned; shaft bent.
11. Tighten or re-align pulleys; replace bent shaft.
12. Worn wheel bearing.
12. Check/replace wheel bearing.
13. Wheel tires worn.
13. Replace tires.
14. Wheels out of balance.
14. Replace wheels.
15. Motor at fault.
15. Repair/replace motor.
1.
2.
3.
4.
G0513 Series Bandsaws (Mfd. Since 07/18)
Symptom
Possible Cause
Possible Solution
Machine stalls
or slows when
operating.
1.
2.
3.
4.
5.
1.
2.
3.
4.
5.
Too much pressure against workpiece.
Workpiece too moist or unsuitable.
Workpiece is warped.
Fence incorrectly adjusted.
V-belt slipping.
6. Run capacitor at fault.
7. Motor connection wired incorrectly.
8. Motor overheated.
9. Contactor has poor contacts or is at fault.
10. Centrifugal switch at fault.
11. Motor at fault.
Decrease the feed rate or workpiece pressure.
Only cut wood and ensure moisture is below 20%.
Straighten workpiece or use a different one.
Adjust/calibrate fence (Page 40).
Tension/replace V-belt (Page 63); ensure pulleys
are aligned.
6. Test/repair/replace.
7. Wire motor correctly. Refer to diagram inside junction
box or the wiring diagrams beginning on Page 71.
8. Let cool, clean motor, and reduce workload.
9. Test all legs for power, test field coil, and fix contacts
or replace if at fault.
10. Adjust/replace centrifugal switch if available.
11. Test for shorted windings, bad bearings and repair
or replace.
Miter bar binds in
miter slot.
1. Miter slot dirty or gummed up.
1. Carefully clean miter slot.
Table does not tilt
to 0 degrees.
1. Pointer or scale calibrated incorrectly.
2. Positive stop bolt not set correctly.
1. Calibrate pointer/scale at true 0 degrees.
2. Adjust positive stop bolt (Page 29).
Table does not tilt
to 45 degrees.
1. Pointer or scale calibrated incorrectly.
2. Machine component blocking path.
1. Calibrate pointer/scale at true 45 degrees.
2. Remove component blocking table.
Table hard to tilt.
1. Sawdust or pitch trapped between trunnion 1. Clean/lubricate
and base.
(Page 59).
2. Metal burrs on trunnion.
2. Remove burrs.
Cuts are rough or
show scoring.
1.
2.
3.
4.
Blade
Blade
Blade
Blade
is overloaded and twists.
TPI is too coarse or speed incorrect.
is loose and slipping on wheels.
tracking is incorrect.
5. Blade has missing or bent teeth.
6. Blade has a faulty weld.
Blade or teeth
break.
sliding
surfaces
of
trunnions
1.
2.
3.
4.
Decrease the feed rate or workpiece pressure.
Use correct blade for application (Page 47).
Re-tension blade (Page 33).
Adjust blade tracking (Page 28) or adjust wheels
coplaner (Page 68).
5. Replace the blade (Page 51).
6. Replace the blade (Page 51).
Decrease blade tension (Page 33).
Use correct blade for application (Page 47).
Reduce feed rate or increase blade speed.
Use a wider arc on outside cuts, or use relief cuts to
make tight inside cuts.
5. Blade is dull.
5. Replace blade (Page 51).
6. Blade tracking is wrong.
6. Adjust blade tracking (Page 46).
7. Blade guides adjusted incorrectly.
7. Re-adjust blade guides (Page 36).
8. Inadequate blade support near cutting 8. Adjust upper blade guide closer to workpiece
area.
(Page 36).
9. Blade weld at fault.
9. Replace blade (Page 51).
10. Wheel tires worn or damaged.
10. Replace tires.
11. Fence or miter slot not aligned with blade.
11. Align miter slot and fence with blade (Page 39).
1.
2.
3.
4.
Blade tension too high.
Incorrect blade for application.
Feed rate or blade speed is too fast.
Operator is cutting corners too sharply.
G0513 Series Bandsaws (Mfd. Since 07/18)
1.
2.
3.
4.
-61-
Symptom
Possible Cause
Blade wears on one 1. Blade contacting table insert.
side, slows, smokes
or shows signs of
overheating.
2. Blade guides are mis-adjusted or worn.
3. Blade has insufficient support near cutting
area.
4. Blade installed backwards.
5. Too much side pressure when feeding
workpiece.
6. Wheels are out of alignment.
7. Dull or incorrect blade for workpiece.
8. Blade is bell-mouthed.
9. Fence not parallel with blade (pressure at
blade backside).
10. Table top is not square with blade.
Possible Solution
1. Re-adjust blade guides (Page 36) to eliminate side
pressure. Adjust table for correct blade clearance
and miter slot alignment (Page 39).
2. Adjust/replace blade guides.
3. Adjust upper blade guide closer to workpiece
(Page 36).
4. Properly install blade with teeth pointing down.
5. Feed workpiece straight into the blade.
6.
7.
8.
9.
Adjust wheels so they are coplanar (Page 68).
Replace blade (Page 51).
Install new blade.
Adjust fence parallel with blade (Page 40).
10. Adjust/shim table/trunnion position until blade and
table are parallel and square (Page 39).
1. Clean out dust port(s).
Sawdust build-up 1. Clogged dust port(s).
inside cabinet.
2. Low CFM (airflow) from dust collection 2. Repair ducting for leaks or clogs, move dust collector
system.
closer to machine, install a stronger dust collector.
1.
2.
3.
4.
5.
6.
7.
8.
Cut is crooked, or
the blade wanders
(blade lead).
1. Feed rate is too fast or blade speed is 1. Adjust feed rate and cutting speed as required.
incorrect.
2. Blade tension is low.
2. Increase the blade tension (Page 33).
3. Blade is dull or damaged.
3. Replace blade (Page 51).
4. Inadequate blade support.
4. Adjust upper blade guide closer to workpiece
(Page 36).
5. Incorrect blade for application.
5. Use wider blade.
6. Blade is tracking incorrectly.
6. Adjust blade tracking (Page 28) (Page 46).
7. Table is loose.
7. Tighten table mounting bolts or tilt lock lever.
8. Fence/miter slot out of alignment.
8. Align table miter slot and fence with blade
(Page 39).
9. Blade guides mis-adjusted.
9. Adjust blade guides (Page 36).
-62-
Tracking is not adjusted properly.
Wheels are not coplanar.
Blade tension is too loose.
Blade guides not adjusted correctly.
Feed rate too fast.
Incorrect blade for bandsaw.
Blade is bell-mouthed, worn or dull.
Rubber tire on wheel is damaged or worn.
1.
2.
3.
4.
5.
6.
7.
8.
Adjust tracking (Page 46).
Adjust wheel coplanarity (Page 68).
Increase blade tension (Page 33).
Adjust blade guides (Page 36).
Decrease feed rate.
Install correct blade for machine.
Install new blade/de-tension blade when not in use.
Replace rubber tires.
Blade tracks
incorrectly, or
comes off wheels.
G0513 Series Bandsaws (Mfd. Since 07/18)
V-Belt Service
Checking V-Belt
To ensure optimum power transmission from the
motor to the blade, the V-belt must be in good
condition and properly tensioned. The belt should
be free of cracks, fraying, and wear. Belt tension
and condition should be checked at least every
3 months—more often if the bandsaw is used
daily.
To replace the V-belt:
1.
DISCONNECT BANDSAW FROM POWER!
2.
Open both wheel covers, and remove the
blade (refer to Blade Changes on Page 51).
3.
Unthread the lower wheel mount bolt shown
in Figure 92, and slide the lower wheel off
the bearing shaft.
To check V-belt tension:
1.
DISCONNECT BANDSAW FROM POWER!
2.
Open the lower wheel cover.
3.
Check the condition of the V-belt. If the V-belt
is cracked, frayed, or glazed, replace it.
4.
Check the V-belt tension by applying moderate pressure between the pulleys (see
Figure 91). If deflection is not approximately
3
⁄4", re-tension the V-belt following the same
steps you normally use when changing blade
speeds (refer to Blade Speed on Page 52 if
necessary).
⁄4"
Deflection
3
Wheel Mount Bolt
Figure 92. Example of wheel mount bolt.
4.
Loosen the motor mount cap screws shown
in Figure 93.
Bandsaw
Wheel
Motor
Wheel
Figure 93. Motor mount cap screws.
5.
Slip the old V-belt off of the wheel pulley and
install the new V-belt in its place.
Replacing V-Belt
6.
To replace the V-belt, you must remove the blade
and the lower wheel. After re-installation, you
must properly re-tension the V-belt.
Properly tension the V-belt and re-tighten the
motor mount cap screws.
7.
Re-install the lower wheel back and secure it
with the wheel mount bolt.
8.
Re-install the blade and close the wheel covers.
Figure 91. V-belt deflection.
Tools Needed:
Qty
Hex Wrench 6mm................................................1
Hex Wrench 8mm................................................1
G0513 Series Bandsaws (Mfd. Since 07/18)
-63-
Blade Lead
"Blade Lead" means that the blade does not cut
straight when using the fence or miter gauge (see
Figure 94). This is a common condition with all
bandsaws. Worn or damaged blades may cause
lead and replacing them will fix the problem. Still, if
your bandsaw is setup correctly and lead occurs,
compensate for it by skewing the fence.
2.
Slide the fence out of the way and cut freehand along the line. Stop at the halfway point.
Turn the bandsaw OFF and wait for the blade
to come to a complete stop.
3.
Clamp the board to the bandsaw table without moving it. Now slide the fence over to
the board so it barely touches one end of
the board.
4.
Loosen the four cap screws on top of the
fence.
5.
Skew the fence as needed until it is parallel to the edge of the scrap piece. You may
need to re-adjust the fence locking mechanisms to gain maximum adjustment.
6.
While maintaining the skew, re-tighten the
fence cap screws.
To compensate for lead when making straight
crosscuts with the miter gauge, you will need
to shift the table:
Figure 94. Example of blade leading away from
line of cut.
To correct blade lead, do the following steps
and make a test cut before skewing the
fence:
1.
Ensure that you have proper blade tension
(refer to Page 33).
2.
Ensure that the blade guides are adjusted
correctly (refer to Pages 36–39).
3.
Ensure that the fence (refer to Page 40) and
miter gauge (refer to Page 41) is parallel to
the blade.
To skew your fence:
1.
-64-
Cut a piece of scrap wood approximately 3⁄4"
thick x 3" wide x 17" long. On a wide face of
the board, draw a straight line parallel to the
long edge.
1.
Set the miter gauge to 90°.
2.
On a scrap piece of wood, mark a line that
is perpendicular to the front edge. Starting
where the line begins, cut the board by
pushing it through the blade with the miter
gauge.
3.
Loosen the table mounting bolts, and shift
the table to compensate for the blade lead.
4.
Repeat Steps 1–3 until the blade cuts
straight when wood is pushed through with
the miter gauge.
If the table is shifted, the fence will be
affected since it is attached.
Lead adjustments will change when new
blades are mounted on the saw.
G0513 Series Bandsaws (Mfd. Since 07/18)
Adjusting Wheel
Brush
Adjusting Tension
Lever
The lower wheel has a brush, as shown in Figure
95, that is designed to sweep sawdust off the
wheel tire as the wheel rotates. In order to work
properly, the brush must make firm contact with
the wheel.
The quick-release tension lever was setup at the
factory for use with the pre-installed 131 1⁄ 2" blade.
However, if you install a different length blade,
you will need to adjust the quick-release adjustment screw so that the quick-release lever works
correctly.
Keep in mind that actual blade lengths may vary
slightly by manufacture.
Tools Needed:
Qty
Hex Wrench 5mm............................................... 1
Wrench 10mm.................................................... 1
Wheel Brush
Figure 95. A wheel brush.
To adjust the quick-release lever:
1.
DISCONNECT BANDSAW FROM POWER!
2.
Open the wheel covers and install a new
blade.
3.
Loosen the jam nut on the tension adjustment
screw 7-10 turns (see Figure 96).
Tools Needed:
Qty
Wrench/Socket 10mm.........................................2
Tension
Adjustment
Screw
To adjust the brush:
1.
DISCONNECT BANDSAW FROM POWER!
2.
Open the lower wheel cover.
3.
Loosen the bolt and nut that secures the
brush in place.
4.
Adjust the brush so it makes firm, even contact with the wheel—without bending the
bristles.
5.
Tighten the bolt and nut to secure the brush
in place.
G0513 Series Bandsaws (Mfd. Since 07/18)
Jam Nut
Wheel Block
Plate
Figure 96. Example of quick-release tension
lever adjustment screw.
4.
Engage the quick-release lever, then turn the
blade tension handwheel until the blade tension matches the mark on the blade tension
scale for the appropriate blade width.
5.
Thread the tension adjustment screw (see
Figure 96) down until it contacts the wheel
block plate, then back it off 1-2 turns.
6.
Re-tighten the jam nut.
-65-
Adjusting Guide
Post Travel
The guide post assembly should remain parallel with the blade front-to-back and side-to-side
along its length of travel. If it does not, follow these
instructions to adjust it.
—If there is no gap between the square and
the guide post along its full length, no
adjustments need to be made. Proceed to
the next procedure.
—If there is a gap between the square and
the guide post, the guide post is not parallel
to the blade. Go to Step 4.
4.
Important: Make sure the table is aligned with the
blade from side-to-side and front-to-back before
beginning these procedures (refer to Aligning
Table on Page 39 for detailed instructions).
Loosen each of the four screws shown in
Figure 98 1⁄4 turn.
Tools Needed:
Machinist's Square............................................. 1
Small Ruler......................................................... 1
Hex Wrench 4mm............................................... 1
Hex Wrench 5mm............................................... 1
Metal Shims...................................... (As Needed)
Checking/Adjusting Guide Post
Parallel with Blade Side-to-Side
1.
DISCONNECT BANDSAW FROM POWER!
2.
Loosen the guide post lock knob, lower the
guide post to within 1" of the table top, then
tighten the knob.
5.
Gently tap the lower part of the guide post in
the appropriate direction until there is no gap
between the square and the guide post.
3.
Place a machinist's square on the table next
to the right hand side of the guide post, as
shown in Figure 97.
6.
Tighten the screws shown in Figure 98.
Guide Post
Figure 98. Guide post adjustment screws.
(Front View)
Figure 97. Example of checking guide post
squareness.
-66-
G0513 Series Bandsaws (Mfd. Since 07/18)
1.
DISCONNECT BANDSAW FROM POWER!
2.
Loosen the guide post lock knob, lower the
blade guide assembly to within 1" of the table
top, then tighten the lock knob.
3.
Remove the screws that secure the guide
post guard and move it up and out of the
way.
4.
Measure the distance "A" between the upper
front face of the guide post rack and the back
of the blade (see Figure 99).
6.
Place the guide post guard on top of the
guide post assembly so you can access the
guide post bracket.
7.
Loosen the four screws shown in Figure 98
on the previous page enough to fit metal
shims between the frame and the guide post
bracket (see Figure 100).
—If the guide post to blade distance is greater
at the bottom than at the top, place a shim
between the bottom of the bracket and the
frame (Shim "A"). This will tilt the bottom of
the guide post toward the blade.
—If the guide post to blade distance is less
at the bottom than at the top, place a shim
between the top of the bracket and the
frame (Shim "B"). This will tilt the bottom of
the guide post away from the blade.
Frame
(Right Side View)
Shim "B"
Guide Post
Blade
Distance "A"
Distance "B"
Guide
Bracket
Figure 99. Example of measuring distance
between rack and blade at top of guide post.
5.
Shim "A"
Guide
Post
Measure the distance "B" between the bottom front face of the guide post rack and the
back of the blade (see Figure 99).
­—If the measurements taken in Steps 4–5
are equal, no adjustments need to be
made. Go to Step 9.
Figure 100. Location for placing shims.
8.
Tighten the four screws shown in Figure 98
on the previous page, then repeat Steps 4–5.
—If the measurements are equal, go to
Step 9.
—If the measurements taken in Steps 4–5
are not equal, go to Step 6.
—If the measurements are not equal, continue adding shims as needed until guide
post rack to blade distance is the same at
the top and bottom.
9.
G0513 Series Bandsaws (Mfd. Since 07/18)
(Left Side View)
Blade
Checking/Adjusting Guide Post
Parallel with Blade Front-to-Back
Re-install the guide post guard with the
screws removed in Step 3.
-67-
Aligning Wheels
3-1⁄2"
Components and Hardware Needed:
Qty
56" Long 2x4...................................................... 1
Tools Needed:
Hex Wrenches 4 & 6 mm..............................1 Ea
Wrench 13mm.................................................... 1
Tape Measure..................................................... 1
Coplanarity Gauge (see Figure 101)................. 1
Straightedge.........................................................
Fine Ruler........................................................... 1
17"
Wheel alignment is one of the most critical factors
for optimal performance from your bandsaw.
56"
22"
Heat, vibration, wandering, blade wear, tire wear
and overall bandsaw wear are considerably
decreased when the wheels are properly aligned
or “coplanar.”
1-1⁄2"
Coplanar wheels automatically track the blade
by balancing it on the crown of the wheel. This is
known as coplanar tracking.
17"
Checking Coplanarity
1.
Make the "Coplanarity Gauge" shown in
Figure 101.
Note: For best results, straighten the 2x4
with a jointer before cutting.
2.
DISCONNECT BANDSAW FROM POWER!
3.
Remove the fence and open both wheel covers.
4.
Adjust the blade guides away from the blade,
loosen blade tension, remove the table insert
and pin, then remove the blade.
5.
Remove the table.
6.
Reinstall the blade, making sure the guide
bearings and support bearings are away from
the blade, then tighten your blade to the tension that it will be used during operation.
7.
Place your coplanarity gauge up against both
wheels in the positions shown in Figure 102.
-68-
Side View
Figure 101. Dimensions of coplanarity gauge.
Coplanarity
Gauge
Gauge Positions
Tracking
Knob
Adjustment
Hub
Wheels
Figure 102. Checking for coplanarity.
G0513 Series Bandsaws (Mfd. Since 07/18)
—If the wheels are coplanar (Figure 104, A),
the straightedge will evenly touch the top
and bottom of both wheels.
A
Coplanar
Coplanarity Gauge
—If the wheels are not coplanar (Figure 104,
B), place the straightedge on the lower
wheel first (ensuring that it touches both
the top and bottom rim), then adjust the
upper wheel tracking knob to make the
upper wheel coplanar and parallel with the
lower wheel.
—If the straightedge does not touch both
wheels evenly, the upper wheel needs to
be shimmed (Figure 104, D) or the lower
wheel needs to be adjusted (Figure 104,
C).
Shimming Upper Wheel
1.
DISCONNECT BANDSAW FROM POWER!
2.
Make sure the top wheel is adjusted parallel
with the bottom wheel.
3.
With a straightedge touching both points of
the wheel that does not need to be adjusted,
measure the distance away from the wheel
that is out of adjustment (see Figure 103).
B
Not Coplanar
Solution:
Adjust
Tracking
Knob
Gauge
Contacts Top
And Bottom of
Both Wheels
C
Gauge Only
Contacts Bottom
Wheel. Top Wheel
Needs to Be Tilted.
D
Not Parallel
Not Coplanar
Parallel, Not
Coplanar
Solution:
Shim Upper
Wheel Out
Gauge Contacts
Wheels Unevenly
Gauge Only
Contacts Bottom
Wheel
Solution:
Adjust
Lower
Wheel
Hub
Difference Between
Wheels
Wheel Out of
Adjustment
Figure 103 Determining distance needed to
shim upper wheel.
4.
Remove the blade from the saw, then remove
the wheel that needs to be shimmed.
5.
Determine how many shim washers you need
to compensate for the distance measured in
Step 3 and place them on the wheel shaft.
G0513 Series Bandsaws (Mfd. Since 07/18)
Figure 104. Coplanar diagram.
6.
Replace the wheel, the original washers, the
securing screw, and the blade.
7.
Tighten the blade, then check the wheels with
the coplanarity gauge. (Wheel coplanarity
changes as the blade is tightened, so it is
best to check the wheel alignment when the
blade is tensioned as it would be for normal
operations.)
-69-
8.
Magnetic Brake
Adjustment
(G0513X2B,
G0513X2BF)
When the wheels are coplanar, place a mark
on each wheel where you held the straightedge. This assures repeated accuracy every
time you adjust your wheels.
Note: When wheels are properly coplanar,
the blade may not be centered on the crown
of the wheel, but it will be balanced.
Adjusting Lower Wheel
Only do this procedure if you cannot make the
wheels coplanar with the tracking knob or by
shimming the upper wheel. Make sure the upper
wheel is adjusted as close as possible to being
coplanar with the lower wheel before beginning.
Do this procedure with the blade fully tensioned.
To adjust the lower wheel:
1.
DISCONNECT BANDSAW FROM POWER!
2.
Loosen the jam nuts on the lower wheel
adjustment hub (see Figure 105).
Adjustment
Hub
Top Tilt
Side
Tilt
Side
Tilt
The space between the magnetic motor brake
and brake shoe is preset by the factory at 0.008"
(0.2mm). To compensate for this wear, you should
adjust this space every two to three years, or if
the brake takes over five seconds for to stop the
motor.
Tools Needed
Phillips Head Screwdriver................................... 1
Feeler Gauge 0.008".......................................... 2
Dollar Bill, Folded Once (Optional)..................... 1
Hex Wrench 3mm............................................... 1
Hex Wrench 4mm............................................... 1
To adjust the magnetic brake:
1.
DISCONNECT BANDSAW FROM POWER!
2.
Remove the motor fan cover, then loosen the
cap screws securing the motor fan and brake
shoe (see Figure 106).
ON
OFF
Brake
Shoe
Bottom Tilt
Figure 105. Lower wheel adjustment control.
3.
4.
5.
-70-
Magnetic
Brake
Loosen one tilt adjustment set screw, then
tighten the opposing set screw approximately
an equal amount.
Check the wheels with the coplanarity gauge,
then adjust the lower wheel at the hub as
needed until it is parallel and coplanar with
the top wheel.
Optional
Dollar Bill
Cap
Screw
Motor
Fan
Figure 106. Adjusting distance between
magnetic brake and brake shoe.
3.
Place the feeler gauge (or dollar bill folded
once) between the brake shoe and magnetic
brake on either side.
4.
Tighten the cap screws on the brake shoe
and motor fan, remove the feeler gauge, then
reinstall the motor fan cover.
Tighten the jam nuts to lock the tilt adjustment set screws in position.
G0513 Series Bandsaws (Mfd. Since 07/18)
machine
SECTION 8: WIRING
These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Compare the manufacture date of your machine to the one
stated in this manual, and study this section carefully.
If there are differences between your machine and what is shown in this section, call Technical Support at
(570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine. An updated
wiring diagram may be available. Note: Please gather the serial number and manufacture date of your
machine before calling. This information can be found on the main machine label.
Wiring Safety Instructions
SHOCK HAZARD. Working on wiring that is connected to a power source is extremely dangerous.
Touching electrified parts will result in personal
injury including but not limited to severe burns,
electrocution, or death. Disconnect the power
from the machine before servicing electrical components!
MODIFICATIONS. Modifying the wiring beyond
what is shown in the diagram may lead to unpredictable results, including serious injury or fire.
This includes the installation of unapproved aftermarket parts.
WIRE CONNECTIONS. All connections must
be tight to prevent wires from loosening during
machine operation. Double-check all wires disconnected or connected during any wiring task to
ensure tight connections.
CIRCUIT REQUIREMENTS. You MUST follow
the requirements at the beginning of this manual
when connecting your machine to a power source.
WIRE/COMPONENT DAMAGE. Damaged wires
or components increase the risk of serious personal injury, fire, or machine damage. If you notice
that any wires or components are damaged while
performing a wiring task, replace those wires or
components.
MOTOR WIRING. The motor wiring shown in
these diagrams is current at the time of printing
but may not match your machine. If you find this
to be the case, use the wiring diagram inside the
motor junction box.
CAPACITORS/INVERTERS. Some capacitors
and power inverters store an electrical charge for
up to 10 minutes after being disconnected from
the power source. To reduce the risk of being
shocked, wait at least this long before working on
capacitors.
EXPERIENCING DIFFICULTIES. If you are experiencing difficulties understanding the information
included in this section, contact our Technical
Support at (570) 546-9663.
The photos and diagrams
included in this section are
best viewed in color. You
can view these pages in
color at www.grizzly.com.
G0513 Series Bandsaws (Mfd. Since 07/18)
-71-
G0513, G0513ANV & G0513X2 Wiring Diagram
Ground
Neutral
Power Switch
(viewed from behind)
POTS
Ground
G
110 VAC
Rewired to 110V
TRATS
Hot
R. Cap 40M 250V
S. Cap 300M 250V
L5-30 Plug
(As Recommended)
Ground
G
Hot
220
VAC
Hot
220 VAC
6-15 Plug
(As Recommended)
1
4
Ground
W
3
2
Motor @220V
Rewired to 110V
R. Cap 40M 250V
S. Cap 300M 250V
1
2
3
4
Ground
Motor @110V
-72-
READ ELECTRICAL SAFETY
ON PAGE 71!
G0513 Series Bandsaws (Mfd. Since 07/18)
G0513X2B Wiring Diagram
Ground
Hot
L2
G
220 VAC
6-15 PLUG
Hot L1
Ground
R
CONTROL PANEL
(viewed from behind)
S
L1/1
L2/3
NO13
L3/5
SDE
MA-18
NC15
SDE
NC16
Ground
A
U
T2/4
AMP
SDE
RA-20
8-12
1/2
3/4
5/6
12
22
8
14
10
96
U
14
RWP
21
13
NO14
T3/6
RESET
Rectifier
PU-23-2
T1/2
22
NO
21
13
98
V
95
22
14
MAGNETIC
SWITCH
FFO
21
13
Ground
U
V
Magnetic Brake
YZG
220V MOTOR
Run
Capacitor
45MFD
450VAC
G0513 Series Bandsaws (Mfd. Since 07/18)
READ ELECTRICAL SAFETY
ON PAGE 71!
-73-
G0513X2BF Wiring Diagram
Ground
Power Supply Junction Box
Ground
Ground
E
G
Hot
R
S
220
VAC
Hot
220V 6-15 Plug
(As Recommended)
Magnetic Switch Assembly
A
Control Panel
(Viewed from Behind)
S
R
22
E
Power
13
14
L1/1
L2/3
L3/5
NO13
Ground
Contactor
SDE MA-18
Rectifier PU-23-2
21
Foot Brake
Switch
NC15
NC16
22
T2/4
T3/6
OL Relay
SDE RA-20
1/2
3/4
ON
E
NO14
8
22
95
10
96
U
13
Set at
8.7A
5/6
12
14
21
RESET
T1/2
98
14
21
OFF
13
V
E
Motor
E
U
V
Ground
Magnetic
Brake YZG
Run Capacitor
45MFD 450VAC
-74-
READ ELECTRICAL SAFETY
ON PAGE 71!
G0513 Series Bandsaws (Mfd. Since 07/18)
G0513X2F 220V Wiring Diagram
Ground
Power Supply Junction Box
Ground
Ground
E
G
Hot
R
S
220
VAC
Hot
220V 6-15 Plug
(As Recommended)
Magnetic Switch Assembly
A
Control Panel
(Viewed from Behind)
1
S
R
L1/1
L2/3
L3/5
22
E
2
Power
1
Ground
Conctactor
SDE MA-09
NC15
NC16
22
T1/2
T2/4
T3/6
Foot Brake Switch
13
14
NO13
21
21
ON
E
NO14
13
14
3
3
1/2
3/4
5/6
RESET
2
OL Relay
SDE RA-20
Set at
9.5A
8
12
U
22
95
10
96
98
14
2
V
3
1
3
E
21
OFF
13
2
1
E
U
Start Capacitor
300MFD 250VAC
V
220V
Motor
Ground
Run Capacitor
40MFD 250VAC
G0513 Series Bandsaws (Mfd. Since 07/18)
READ ELECTRICAL SAFETY
ON PAGE 71!
-75-
G0513X2F 110V Wiring Diagram
Power Supply Junction Box
Ground
Ground
Ground
E
Neutral
R
S
W
G
110 VAC
Magnetic Switch Assembly
A
Control Panel
(Viewed from Behind)
L5-30 Plug
(As Recommended)
1
S
R
L1/1
L2/3
L3/5
22
E
2
Power
Foot Brake Switch
13
14
NO13
21
1
Ground
Conctactor
SDE MA-18
NC15
NC16
22
T1/2
T2/4
T3/6
21
ON
E
NO14
13
14
3
3
1/2
3/4
5/6
RESET
2
OL Relay
SDE RA-30
18
26
Set at
19A
U
22
95
22
98
96
14
2
V
3
3
1
21
OFF
13
2
1
E
E
U
Start Capacitor
300MFD 250VAC
V
Ground
110V
Motor
Run Capacitor
40MFD 250VAC
-76-
READ ELECTRICAL SAFETY
ON PAGE 71!
G0513 Series Bandsaws (Mfd. Since 07/18)
SECTION 9: PARTS
G0513 & G0513ANV Main
55
55V2 (G0513ANV)
55A
55AV2 (G0513ANV)
50
5
5V2 (G0513ANV)
4
71
61
68
49
9
48
11-1
13
19
18
17
16
67
46
15
45
11
12
8
44
22
36 42
17
20
28
18
26
23
22
80
79
87
61
152
84
30
83
82
83
61
27
58
57
25
56
86
21
89
82-6
119 97
92
We do our best to stock replacement
parts when possible, but we cannot
guarantee that all parts shown are available for purchase. Call (800) 523-4777
or visit www.grizzly.com/parts to check
for availability.
78
60
31
29
81
75
62
41
40
43
43V2 (G0513ANV)
18
17
24
39
32 33 34 35
175
24
39
64 88
37
76
39
60
152
63
61
65
38
20
74
48
50
176 39
21
73
66
47 10
14
69
72
70
59
61
84
90
82-5
82-1
82-4
91
93
85
82-2
82-3
82-9
82-8
94
82-7
82-9A
82-10 82-11
95
95V2 (G0513ANV)
G0513 Series Bandsaws (Mfd. Since 07/18)
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
-77-
G0513 & G0513ANV Main Parts List
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
4
5
5V2
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
43V2
44
45
46
47
48
49
50
55
55V2
55A
55AV2
56
57
58
P0513004
P0513005
P0513ANV005V2
P0513008
P0513009
P0513010
P0513011
P0513012
P0513013
P0513014
P0513015
P0513016
P0513017
P0513018
P0513019
P0513020
P0513021
P0513022
P0513023
P0513024
P0513025
P0513026
P0513027
P0513028
P0513029
P0513030
P0513031
P0513032
P0513033
P0513034
P0513035
P0513036
P0513037
P0513038
P0513039
P0513040
P0513041
P0513042
P0513043
P0513043V2
P0513044
P0513045
P0513046
P0513047
P0513048
P0513049
P0513050
P0513055
P0513ANV055V2
P0513X2055A
P0513ANV055AV2
P0513056
P0513057
P0513058
LIFTING EYE BOLT M10-1.5
MACHINE BODY (G0513)
MACHINE BODY V2.04.17 (G0513ANV)
FLAT WASHER 6MM
POWER CORD 14G 3W 72"
HEX NUT M6-1
POINTER
STEP SCREW M4-.7 X 5
HINGE SHAFT
ROLL PIN 5 X 36
UPPER WHEEL SHAFT HINGE
UPPER WHEEL SHAFT
BUSHING
BALL BEARING 6204-2RS
UPPER WHEEL 17"
INT RETAINING RING 47MM
WHEEL FLAT WASHER 8MM
HEX BOLT M8-1.25 X 30
SAW BLADE 131.5" X 1/2" 6TPI HOOK
LOCK WASHER 8MM
HEX BOLT M6-1 X 30
URETHANE TIRE 17" 1-PAIR
LOWER WHEEL 17"
LOWER WHEEL PULLEY
HEX NUT 1-14
LOCK WASHER 1"
MOTOR CORD 14G 3W
COMPRESSION SPRING 7 X 8 X 90
ROLL PIN 3 X 16
ALIGNMENT PLATE
THRUST BEARING 51201
2-BUTTON POWER SWITCH
TENSION HANDWHEEL
TENSION ADJUSTING ROD
FLANGE SCREW M5-.8 X 10
EXT TOOTH WASHER 5MM
HEX NUT M5-.8
FLANGE SCREW M5-.8 X 16
SWITCH BACK PLATE
SWITCH BACK PLATE V2.04.17 (G0513ANV)
HEX BOLT M8-1.25 X 16
FLAT WASHER 8MM
UPPER WHEEL SLIDING BRACKET
HEX BOLT M6-1 X 25
STEEL BLIND RIVET 3 X 13MM
HEX BOLT M6-1 X 10
CLEAR WINDOW
UPPER WHEEL COVER (G0513)
UPPER WHEEL COVER V2.04.17 (G0513ANV)
UPPER WHEEL COVER ASSY (G0513)
UPPER WHEEL COVER ASSY V2.04.17 (G0513ANV)
HEX BOLT M6-1 X 10
FLAT WASHER 6MM
WHEEL BRUSH
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
78
79
80
81
82
82-1
82-2
82-3
82-4
82-5
82-6
82-7
82-8
82-9
82-9A
82-10
82-11
83
84
85
86
87
88
89
90
91
92
93
94
95
95V2
97
119
152
175
176
P0513059
P0513060
P0513061
P0513062
P0513063
P0513064
P0513065
P0513066
P0513067
P0513068
P0513069
P0513070
P0513071
P0513072
P0513073
P0513074
P0513075
P0513076
P0513078
P0513079
P0513080
P0513081
P0513082
P0513082-1
P0513082-2
P0513082-3
P0513082-4
P0513082-5
P0513082-6
P0513082-7
P0513082-8
P0513082-9
P0513082-9A
P0513082-10
P0513082-11
P0513083
P0513084
P0513085
P0513086
P0513087
P0513088
P0513089
P0513090
P0513091
P0513092
P0513093
P0513094
P0513095
P0513ANV095V2
P0513097
P0513119
P0513152
P0513175
P0513176
HEX BOLT M6-1 X 25
STAR KNOB
LOCK NUT M6-1
STRAIN RELIEF 16MM STRAIGHT LT
HEIGHT POINTER
HEX NUT M8-1.25
HEX BOLT M8-1.25 X 100
STAR KNOB BOLT M10-1.5 X 20
STAR KNOB BOLT M10-1.5 X 55
THREADED HANDLE M10-1.5
CAM
PILLOW BLOCK
HANDLE M12-1.75
LEVER
HEX NUT M12-1.75
LEVER HUB
CAP SCREW M8-1.25 X 20
LOCK WASHER 8MM
SHAFT COVER
SET SCREW M8-1.25 X 20
HEX NUT M8-1.25
LOWER WHEEL SHAFT
MOTOR 2HP 110V/220V 1-PH
MOTOR FAN COVER
MOTOR FAN
S CAPACITOR 300M 250V 1-1/2 X 2-3/8
S CAPACITOR COVER
R CAPACITOR 40M 250V 1-1/2 X 2-3/4
R CAPACITOR COVER
MOTOR JUNCTION BOX
CONTACT PLATE
CENTRIFUGAL SWITCH 5/8-1725
CENTRIFUGAL SWITCH W/CONT PLATE
BALL BEARING 6203ZZ
BALL BEARING 6205ZZ
HEX BOLT M5-.8 X 16
LOCK WASHER 5MM
MOTOR MOUNT BRACKET
CAP SCREW M8-1.25 X 20
STRAIN RELIEF PLATE 2-HOLE
FLANGE SCREW M5-.8 X 10
PILLOW BLOCK
KEY 5 X 5 X 35
HEX BOLT M8-1.25 X 20 LH
MOTOR PULLEY TYPE-A 3.5"
V-BELT A42
HEX BOLT M6-1 X 10
LOWER WHEEL COVER (G0513)
LOWER WHEEL COVER V2.04.17 (G0513ANV)
FLAT WASHER 8MM
FLAT WASHER 8MM
HEX BOLT M6-1 X 20
HEX BOLT M6-1 X 20
BUSHING
-78-
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
G0513 Series Bandsaws (Mfd. Since 07/18)
G0513 & G0513ANV Table, Trunnion & Lower
Blade Guides
127
124
115
117
112
119
118
113
113
120
116
128
126
129
114
115
148
130
121
122
123
135
99
100
163
116
131
96
133
109
110
111
103
101
77
132
107
108
139
103
104
102
105
196
106
134
98
REF PART #
DESCRIPTION
REF
PART #
DESCRIPTION
77
96
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
LOCK WASHER 8MM
FLAT WASHER 8MM
CAP SCREW M10-1.5 X 35
HEX NUT M10-1.5
TRUNNION GEAR
STAR KNOB BOLT
TRUNNION SUPPORT BRACKET
LOCK WASHER 10MM
FLAT WASHER 10MM
CAP SCREW M6-1 X 15
CAP SCREW M6-1 X 50
ALIGNMENT ROD
HEX NUT M6-1
ADJUSTMENT KNOB BOLT M6-1
BALL BEARING 6000ZZ
BUTTON HD CAP SCR M10-1.5 X 20
FLAT WASHER 8MM
FLAT WASHER 8MM
PHLP HD SCR M4-.7 X 6
GEAR PLATE
LOCK NUT M8-1.25
PHLP HD SCR M4-.7 x 6
118
119
120
121
122
123
124
126
126
127
128
129
130
131
132
133
134
135
139
148
163
196
P0513118
P0513119
P0513120
P0513121
P0513122
P0513123
P0513124
P0513126
P0513ANV126
P0513127
P0513128
P0513129
P0513130
P0513131
P0513132
P0513133
P0513134
P0513135
P0513139
P0513148
P0513163
P0513196
LOCK HANDLE M8-1.25
FLAT WASHER 8MM
POINTER
TRUNNION PLATE
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 16
CARRIAGE BOLT M8-1.25 X 80
TABLE 17" X 17"
TABLE 17" X 17" (G0513ANV)
TABLE INSERT
TABLE PIN
HEX BOLT M8-1.25 X 20 LH
LEFT GUARD
THUMB SCREW M6-1 X 16
LOWER BLADE GUIDE SUPPORT
BLADE GUIDE
GUIDE ADJUSTMENT SHAFT
RIGHT GUARD
CAP SCREW M10-1.5 X 30
CARRIAGE BOLT M8-1.25 X 85
LOCK WASHER 8MM
STEEL BALL 5MM
P0513077
P0513096
P0513098
P0513099
P0513100
P0513101
P0513102
P0513103
P0513104
P0513105
P0513106
P0513107
P0513108
P0513109
P0513110
P0513111
P0513112
P0513113
P0513114
P0513115
P0513116
P0513117
G0513 Series Bandsaws (Mfd. Since 07/18)
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
-79-
G0513 & G0513ANV Fence
216
211
202
218
220
212
204
207
208
222
213
215
209
225
222
210
205
203
226
227
223
220
217
125
206
221
214
219
201
REF PART #
DESCRIPTION
REF
PART #
DESCRIPTION
125
201
202
203
204
205
206
207
208
209
210
211
212
213
FENCE ASSEMBLY W/RAILS
FRONT FENCE RAIL
FENCE BASE
ALIGNMENT SHAFT
LOCK BLOCK SHAFT
SPRING PLATE
SPACER PLATE
FENCE
SLEEVE
FENCE LOCK HANDLE
RAIL PAD
CONVEX WINDOW
CAP SCREW M6-1 X 55
LOCK CAM
214
215
216
217
218
219
220
221
222
223
225
226
227
P0513214
P0513215
P0513216
P0513217
P0513218
P0513219
P0513220
P0513221
P0513222
P0513223
P0513225
P0513226
P0513227
REAR FENCE RAIL
HEX NUT M6-1
FLANGE SCREW M4-.7 X 6
FRONT RAIL END CAP
FENCE END CAP
REAR RAIL END CAP
TAP SCREW M3.5 X 8
FENCE SCALE
HEX NUT M6-1
LOCK WASHER 6MM
HEX BOLT M6-1 X 20
FLANGE SCREW M4-.7 X 10
FLAT WASHER 6MM
-80-
P0513125
P0513201
P0513202
P0513203
P0513204
P0513205
P0513206
P0513207
P0513208
P0513209
P0513210
P0513211
P0513212
P0513213
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
G0513 Series Bandsaws (Mfd. Since 07/18)
G0513 & G0513ANV Upper Blade Guides &
Miter Gauge
163
164V2
165
162
174V2
166
157A
160
161V2
167
168
142
159
140
169
158
6
170
141
171
136
137
151
172
138
157
163
149
155
156
154
153
149
150
144
138-1
192
149
145 196
146
143
134
193
147
194
173-5
173-4
173-6
173
173-2
173-9
173-3
173-1
173-8
173-7
G0513 Series Bandsaws (Mfd. Since 07/18)
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
-81-
G0513 & G0513ANV Upper Blade Guides &
Miter Gauge Parts List
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
6
134
136
137
138
138
138-1
140
141
142
142
143
144
145
146
147
149
150
151
153
154
155
156
157A
157
158
159
160
P0513006
P0513134
P0513136
P0513137
P0513138
P0513ANV138
P0513138-1
P0513140
P0513141
P0513142
P0513ANV142
P0513143
P0513144
P0513145
P0513146
P0513147
P0513149
P0513150
P0513151
P0513153
P0513154
P0513155
P0513156
P0513157A
P0513157
P0513158
P0513159
P0513160
SET SCREW M5-.8 X 5
GUIDE ADJUSTMENT SHAFT
CAP SCREW M8-1.25 X 80
FLAT WASHER 8MM
UPPER BLADE GUARD (G0513/G0513P)
UPPER BLADE GUARD (G0513ANV)
BLADE GUARD SCALE
STEP SCREW M4-.7 X 5
FIBER WASHER 5MM
SLIDING PLATE (G0513/G0513P)
SLIDING PLATE (G0513ANV)
EXT RETAINING RING 15MM
BALL BEARING 6202ZZ
UPPER BLADE GUIDE SUPPORT
BLADE GUIDE
THUMB SCREW M6-1 X 16
CAP SCREW M6-1 X 15
ADJUSTMENT SHAFT
UPPER SPACING SLEEVE
UPPER GUIDE SUPPORT BLOCK
PHLP HD SCR M4-.7 X 10
HEX NUT M4-.7
RACK
GUIDE POST ASSEMBLY
GUIDE POST
ELEVATION HANDWHEEL
HEX BOLT M6-1 X 20
PINION GEAR STEP BOLT
161V2
162
163
164V2
165
166
167
168
169
170
171
172
173
173-1
173-2
173-3
173-4
173-5
173-6
173-7
173-8
173-9
174V2
192
193
194
196
P0513161V2
P0513162
P0513163
P0513164V2
P0513165
P0513166
P0513167
P0513168
P0513169
P0513170
P0513171
P0513172
P0513173
P0513173-1
P0513173-2
P0513173-3
P0513173-4
P0513173-5
P0513173-6
P0513173-7
P0513173-8
P0513173-9
P0513174V2
P0513192
P0513193
P0513194
P0513196
THREADED BUSHING V2.06.09
CAP SCREW M8-1.25 X 20
LOCK WASHER 8MM
THREADED GUIDE BRACKET 14MM V2.06.09
WORM CYLINDER
FIXED PLATE
PINION GEAR 15T
PINION GEAR STEP BOLT
BRACKET COVER
CAP SCREW M8-1.25 X 16
PHLP HD SCR M4-.7 X 8
SET SCREW M6-1 X 16
MITER GAUGE ASSY
GUIDE BAR
T-SLOT WASHER 5MM
INDICATOR
NYLON WASHER 1/4"
MITER GAUGE HANDLE 1/4"-20
MITER GAUGE BODY
INDEXING PIN
PHLP HD SCR M6-1 X 6
FLANGE SCREW M5-.8 X 8
HEX NUT M16-1.5 THIN
HEX WRENCH 5MM
HEX WRENCH 8MM
WRENCH 10 X 13MM OPEN-END
STEEL BALL 5MM
-82-
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
G0513 Series Bandsaws (Mfd. Since 07/18)
184
###
###
(08/29/18)
• Scale= 1:1
(unless otherwise noted)
SN
• Labels MUST be made of
chemical-resistant material
Date
Mfd. for Grizzly in Taiwan
To reduce risk of serious injury when using this machine:
1. Read & understand owner’s manual before operating.
2. Never touch moving blade—keep hands out of blade path.
3. Always wear approved eye protection and respirator.
4. Only remove jammed cutoff pieces when blade is stopped.
5. Use push stick or holding jig to cut small or narrow pieces.
6. Disconnect power before changing blades or adjusting.
7. Maintain adjustment of blade tension, tracking, & guides.
8. Keep upper guide adjusted to just clear the workpiece.
9. Hold workpiece firmly against table to maintain control.
10. Only run saw with wheel covers closed & all guards in place.
11. Never reach under table while blade is in motion.
12. Secure/remove loose clothing and long hair.
13. DO NOT expose to rain or use in wet locations.
14. DO NOT operate under influence of drugs or alcohol.
15. Prevent unauthorized use by children or untrained users;
restrict access or disable machine when unattended.
G0513 Machine Labels
***
Note: Labels marked *** have changed since last sent.
PANTONE 485 C or RAL 3001
MODEL G0513
17" 2 HP BANDSAW
Specifications
Motor: 2 HP, 110V/220V, 1-PH, 60 Hz
Motor Prewired: 220V
Amp Draw: 10A at 220V; 20A at 110V
Table Size: 17" x 17"
Blade Speeds: 1700 & 3500 FPM
Blade Length: 131-1/2"
Blade Width Range: 1/8" – 1"
Max. Cutting Width Left of Blade: 16-1/4"
Max. Cutting Height: 12-1/8"
Table Tilt: 10˚L ⁄ 45˚R
Weight: 266 lbs.
Note: Labels marked with ### must have individual
letters/numbers. DO NOT print with clear background.
PANTONE 151 C or RAL 2005
PANTONE 711C or RAL 3020
PANTONE 568C
DANGER
COLOR CODES
WARNING
191(7/12/13)
GRIZZLY GREEN
Mfd. for Grizzly in Taiwan
G0513
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material
GRIZZLY LOGO RED
SN
G0513 Machine Labels
Date
(08/29/18)
G0513 Series
Generic Labels
186
grizzly.com
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
PANTONE 485 C or RAL 3001
COLOR CODES
DANGER
To reduce risk of serious injury when using this machine:
1. Read & understand owner’s manual before operating.
2. Never touch moving blade—keep hands out of blade path.
3. Always wear approved eye protection and respirator.
4. Only remove jammed cutoff pieces when blade is stopped.
5. Use push stick or holding jig to cut small or narrow pieces.
6. Disconnect power before changing blades or adjusting.
7. Maintain adjustment of blade tension, tracking, & guides.
8. Keep upper guide adjusted to just clear the workpiece.
9. Hold workpiece firmly against table to maintain control.
10. Only run saw with wheel covers closed & all guards in place.
11. Never reach under table while blade is in motion.
12. Secure/remove loose clothing and long hair.
13. DO NOT expose to rain or use in wet locations.
14. DO NOT operate under influence of drugs or alcohol.
15. Prevent unauthorized use by children or untrained users;
restrict access or disable machine when unattended.
• Scale= 1:1
(unless otherwise noted)
Specifications
Motor: 2 HP, 110V/220V, 1-PH, 60 Hz
Motor Prewired: 220V
Amp Draw: 10A at 220V; 20A at 110V
Table Size: 17" x 17"
Blade Speeds: 1700 & 3500 FPM
Blade Length: 131-1/2"
Blade Width Range: 1/8" – 1"
Max. Cutting Width Left of Blade: 16-1/4"
Max. Cutting Height: 12-1/8"
Table Tilt: 10˚L ⁄ 45˚R
Weight: 266 lbs.
Note: Labels marked with ### must have individual
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
letters/numbers. DO NOT print with clear background.
***
• 1:1 Sizing (Labels are
actual size)
MODEL
• Labels must be made
of G0513
17" 2 HP BANDSAW
oil-resistant material
• Labels MUST be made of
chemical-resistant material
G0513
177V2
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. If
Note: Labels marked *** have changed
since
lastaresent.
artwork
changes
required, contact us immediately at manuals@grizzly.com.
G0513 Series
Generic Labels
G0513 Labels
G0513 Series
Generic Labels
Model G8588
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material
(7/12/13)
185
181
WARNING!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
INJURY HAZARD!
Do not open door
while machine is
connected to power
or blade is in motion.
179
WARNING!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
189
G0513 Series
Generic Labels
INJURY HAZARD!
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material
Do not open door
while machine is
connected to power
or blade is in motion.
(7/12/13)
WARNING!
EYE/LUNG INJURY
INJURY/SHOCK
HAZARD!
HAZARD!
Always wear INC.
safety
COPYRIGHT © GRIZZLY INDUSTRIAL,
Disconnect power
glasses and a
adjustments,
before
DO NOT REPRODUCE
OR
CHANGE THIS
ARTWORK
respirator
when
maintenance, or
Grizzly will not accept
changed without
approval. If
usinglabels
this machine.
service.
G0513 Series
Generic Labels
artwork changes are required, contact us immediately at manuals@grizzly.com.
(7/12/13)
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material
180
WARNING!
EYE/LUNG INJURY
HAZARD!
Always wear safety
glassesWARNING!
and a
respirator when
To reduce
risk of death
using
this machine.
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
.
WARNING!
WITHOUT
WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. If
To reduce risk ofchanges
death
areINJURY
required,
contact us immediately at manuals@grizzly.com.
HAZARD!
• 1:1artwork
Sizing (Labels
are
or serious injury, read
manual BEFORE using
Do not open door
actual size)
machine.
while machine is
To get a new manual,
connected
• call
Labels
must be made
of to power
(800) 523-4777 or
or blade is in motion.
go
to www.grizzly.commaterial
oil-resistant
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
INJURY HAZARD!
Do not open door
while machine is
connected to power
or blade is in motion.
183
195
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
WARNING!
FOR GRIZZLY
MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
EYE/LUNG
INJURY APPROVAL!
Grizzly will not accept labels changed without approval. If
WITHOUT
WRITTEN
INJURY/SHOCK
HAZARD!
artwork
changes are required,
contact us immediately at manuals@grizzly.com.
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
Disconnect power
before adjustments,
maintenance, or
service.
WARNING!
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
178
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
178
187
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
DO NOT REPRODUCE OR CHANGE THIS ARTWORK
Grizzly will not accept labels changed without approval. If
rk changes are required, contact us immediately at manuals@grizzly.com.
G0513 Series
Generic Labels
188
(7/12/13)
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material
181
WARNING!
197
grizzly.com
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
INJURY HAZARD!
Do not open door
while machine is
connected to power
or blade is in motion.
WARNING!
EYE/LUNG INJURY
REF
PART #
DESCRIPTION
177V2
178
179
180
181
183
184
185
P0513177V2 MACHINE ID LABEL V2.07.18
P0513178
ELECTRICITY LABEL
P0513179
GLASSES/RESPIRATOR LABEL
P0513180
READ MANUAL LABEL
P0513181
DOOR WARNING LABEL
P0513183
DISCONNECT POWER LABEL
P0513184
GRIZZLY NAMEPLATE-SMALL
P0513185
SAW TENSION LABEL
INJURY/SHOCK
REF PART #
DESCRIPTION
186
187
188
189
191
195
197
MODEL NUMBER LABEL
TOUCH-UP PAINT, GRIZZLY GREEN
TOUCH-UP PAINT, LIGHT GRAY
GUIDE POST ADJUST LABEL
BLADE TENSION SCALE LABEL
GUIDE POST LOCK LABEL
GRIZZLY.COM LABEL
P0513186
P0513187
P0513188
P0513189
P0513191
P0513195
P0513197
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.
G0513 Series Bandsaws (Mfd. Since 07/18)
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
-83-
G0513ANV Labels
192
189
182
191V2
183
185
179
188
180
178
177V2
182
194V2
187V2
186
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
177V2
178
179
180
182
183
185
P0513ANV177V2
P0513ANV178
P0513ANV179
P0513ANV180
P0513ANV182
P0513ANV183
P0513ANV185
MACHINE ID LABEL V2.04.17
ELECTRICITY LABEL
SAFETY GLASSES/RESPIRATOR LABEL
READ MANUAL LABEL
DONT OPEN LABEL
UNPLUG BANDSAW LABEL
SAW TENSION LABEL
186
187V2
188
189
191V2
192
194V2
P0513ANV186
P0513ANV187V2
P0513ANV188
P0513ANV189
P0513ANV191V2
P0513ANV192
P0513ANV194V2
MODEL NUMBER LABEL
TOUCH-UP PAINT, 35TH ANV ED. V2.04.17
ORANGE TOUCH-UP PAINT, PANTONE 151C
GUIDE POST ADJUST LABEL
GRIZZLY LOGO NAMEPLATE V2.04.17
ORANGE GRIZZLY.COM LABEL
35TH ANNIVERSARY LABEL V2.04.17
-84-
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
G0513 Series Bandsaws (Mfd. Since 07/18)
G0513X2 Main
72
71
55A
59
69
61
16
7
15
13
47
48
45
50
44
3
61
43
39
23
36 42
24
39
40
60
111
39
64 88
37
32 33
63
65
38
34 35
28
66
5
46
17-5
67
10
17-4
17-2
21
68
8
17-2
17-3
17-1
14
4
9
11
12
17
22
75
76
79
80
81
55
48
78
74
50
49
39
73
70
62
41
87
61
60
2
25
111
18-4
18-5
22
18-2
18-3
24
18-1
21
18-3
29
30
31
61
58
18
18-2
119
90
97
91
82-1V2
92
93
61
82-2V2
82-3V2
82-4V2
82-5V2
56
82-8
82-9
82-6V2
82-7V2
57
84
G0513 Series Bandsaws (Mfd. Since 07/18)
82V2
83
82-10
82-11
85
94
95A
83
84
86
89
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
-85-
G0513X2 Main Parts List
REF PART #
DESCRIPTION
REF
PART #
DESCRIPTION
2
3
4
5
7
8
9
10
11
12
13
14
15
16
17
17-1
17-2
17-3
17-4
17-5
18
18-1
18-2
18-3
18-4
18-5
21
22
23
24
25
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
55A
SET SCREW M6-1 X 10
BUSHING
LIFTING EYE BOLT M10-1.5
MACHINE BODY
BUSHING
FLAT WASHER 6MM
POWER CORD 14G 3W 72"
HEX NUT M6-1
POINTER
STEP SCREW M4-.7 X 5
HINGE SHAFT
ROLL PIN 5 X 36
UPPER WHEEL SHAFT HINGE
UPPER WHEEL SHAFT
UPPER WHEEL ASSEMBLY
BUSHING
BALL BEARING 6204-2RS
INT RETAINING RING 47MM
UPPER WHEEL 17"
URETHANE TIRE 17" 1-PAIR
LOWER WHEEL ASSEMBLY
BUSHING
BALL BEARING 6204-2RS
INT RETAINING RING 47MM
LOWER WHEEL 17"
URETHANE TIRE 17" 1-PAIR
WHEEL FLAT WASHER 8MM
CAP SCREW M8-1.25 X 16
SAW BLADE 131.5" X 1/2" 6TPI HOOK
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 20
LOWER WHEEL PULLEY
HEX NUT 1-14
LOCK WASHER 1"
MOTOR CORD 14G 3W
COMPRESSION SPRING 7 X 8 X 90
ROLL PIN 3 X 16
ALIGNMENT PLATE
THRUST BEARING 51201
2-BUTTON START/STOP SWITCH
TENSION HANDWHEEL
TENSION ADJUSTING ROD
FLANGE SCREW M5-.8 X 10
EXT TOOTH WASHER 5MM
HEX NUT M5-.8
FLANGE SCREW M5-.8 X 16
SWITCH BACK PLATE
CAP SCREW M8-1.25 X 16
FENDER WASHER 8MM
UPPER WHEEL SLIDING BRACKET
CAP SCREW M8-1.25 X 50
STEEL BLIND RIVET 3 X 13MM
CAP SCREW M6-1 X 10
CLEAR WINDOW
UPPER WHEEL COVER ASSY
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
78
79
80
81
82V2
82-1V2
82-2V2
82-3V2
82-4V2
82-5V2
82-6V2
82-7V2
82-8
82-9
82-10
82-11
83
84
85
86
87
88
89
90
91
92
93
94
95A
97
111
119
P0513X2055
P0513X2056
P0513X2057
P0513X2058
P0513X2059
P0513X2060
P0513X2061
P0513X2062
P0513X2063
P0513X2064
P0513X2065
P0513X2066
P0513X2067
P0513X2068
P0513X2069
P0513X2070
P0513X2071
P0513X2072
P0513X2073
P0513X2074
P0513X2075
P0513X2076
P0513X2078
P0513X2079
P0513X2080
P0513X2081
P0513X2082V2
P0513X2082-1V2
P0513X2082-2V2
P0513X2082-3V2
P0513X2082-4V2
P0513X2082-5V2
P0513X2082-6V2
P0513X2082-7V2
P0513X2082-8
P0513X2082-9
P0513X2082-10
P0513X2082-11
P0513X2083
P0513X2084
P0513X2085
P0513X2086
P0513X2087
P0513X2088
P0513X2089
P0513X2090
P0513X2091
P0513X2092
P0513X2093
P0513X2094
P0513X2095A
P0513X2097
P0513X2111
P0513X2119
UPPER WHEEL COVER
HEX BOLT M6-1 X 25
FLAT WASHER 6MM
WHEEL BRUSH
CAP SCREW M6-1 X 25
STAR KNOB
LOCK NUT M6-1
STRAIN RELIEF 16MM STRAIGHT LT
HEIGHT POINTER
HEX NUT M8-1.25
HEX BOLT M8-1.25 X 90
STAR KNOB BOLT M10-1.5 X 20
STAR KNOB BOLT M10-1.5 X 55
THREADED HANDLE M10-1.5
CAM
PILLOW BLOCK
HANDLE M12-1.75
LEVER
HEX NUT M12-1.75
LEVER HUB
BUTTON HD CAP SCR M8-1.25 X 20
LOCK WASHER 8MM
SHAFT COVER
SET SCREW M8-1.25 X 20
HEX NUT M8-1.25
LOWER WHEEL SHAFT
MOTOR 2HP 110V/220V 1-PH V2.01.10
MOTOR FAN COVER V2.01.10
MOTOR FAN V2.01.10
S CAPACITOR 300M 250V 1-1/2 X 2-3/8 V2.01.10
S CAPACITOR COVER V2.01.10
R CAPACITOR 40M 250V 1-3/8 X 2-5/8 V2.01.10
R CAPACITOR COVER V2.01.10
MOTOR JUNCTION BOX V2.01.10
CONTACT PLATE 5/8
CENTRIFUGAL SWITCH 5/8-1725
BALL BEARING 6203ZZ
BALL BEARING 6205ZZ
HEX BOLT M10-1.5 X 25
LOCK WASHER 10MM
MOTOR MOUNT BRACKET
BUTTON HD CAP SCR M8-1.25 X 20
STRAIN RELIEF PLATE 2-HOLE
FLANGE SCREW M5-.8 X 10
PILLOW BLOCK
KEY 5 X 5 X 35
HEX BOLT M8-1.25 X 20 LH
MOTOR PULLEY TYPE-A 3.5"
V-BELT A42
CAP SCREW M6-1 X 10
LOWER WHEEL COVER
FENDER WASHER 8MM
CAP SCREW M6-1 X 20
LOCK WASHER 4MM
-86-
P0513X2002
P0513X2003
P0513X2004
P0513X2005
P0513X2007
P0513X2008
P0513X2009
P0513X2010
P0513X2011
P0513X2012
P0513X2013
P0513X2014
P0513X2015
P0513X2016
P0513X2017
P0513X2017-1
P0513X2017-2
P0513X2017-3
P0513X2017-4
P0513X2017-5
P0513X2018
P0513X2018-1
P0513X2018-2
P0513X2018-3
P0513X2018-4
P0513X2018-5
P0513X2021
P0513X2022
P0513X2023
P0513X2024
P0513X2025
P0513X2028
P0513X2029
P0513X2030
P0513X2031
P0513X2032
P0513X2033
P0513X2034
P0513X2035
P0513X2036
P0513X2037
P0513X2038
P0513X2039
P0513X2040
P0513X2041
P0513X2042
P0513X2043
P0513X2044
P0513X2045
P0513X2046
P0513X2047
P0513X2048
P0513X2049
P0513X2050
P0513X2055A
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
G0513 Series Bandsaws (Mfd. Since 07/18)
G0513X2 Labels
216V2
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
MODEL G0513X2
oil-resistant material
17" EXTREME SERIES BANDSAW
(7/12/13)
Specifications
(08/29/18)
• Scale= 1:1
(unless otherwise noted)
G0513 Machine Labels
• Labels MUST be made of
chemical-resistant material
***
Note: Labels marked *** have changed since last sent.
Note: Labels marked with ### must have individual
letters/numbers. DO NOT print with clear background.
PANTONE 568C
PANTONE 485 C or RAL 3001
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
PANTONE 151 C or RAL 2005
WARNING!
PANTONE 711C or RAL 3020
205
COLOR CODES
(7/12/13)
DANGER
Do not open door
while machine is
connected to power
or blade is in motion.
WARNING
Mfd. for Grizzly in Taiwan
INJURY HAZARD!
GRIZZLY GREEN
SN
WARNING!
G0513X2
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material
GRIZZLY LOGO RED
G0513 Series
Generic Labels
Date
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
To reduce risk of serious injury when using this machine:
1. Read & understand owner’s manual before operating.
2. Never touch moving blade—keep hands out of blade path.
3. Always wear approved eye protection and respirator.
4. Only remove jammed cutoff pieces when blade is stopped.
5. Use push stick or holding jig to cut small or narrow pieces.
6. Disconnect power before changing blades or adjusting.
7. Maintain adjustment of blade tension, tracking, & guides.
8. Keep upper guide adjusted to just clear the workpiece.
9. Hold workpiece firmly against table to maintain control.
10. Only run saw with wheel covers closed & all guards in place.
11. Never reach under table while blade is in motion.
12. Secure/remove loose clothing and long hair.
13. DO NOT expose to rain or use in wet locations.
14. DO NOT operate under influence of drugs or alcohol.
15. Prevent unauthorized use by children or untrained users;
restrict access or disable machine when unattended.
202
###
Motor: 2 HP, 110V/220V, 1-PH, 60 Hz
Motor Prewired: 220V
Amp Draw: 9.5A at 220V; 19A at 110V
Table Size: 23-5/8" x 17-1/4"
Blade Speeds: 1700 & 3500 FPM
Blade Length: 131-1/2"
Blade Width Range: 1/8" – 1"
Max. Cutting Width Left of Blade: 16-1/4"
Max. Cutting Height: 12"
Table Tilt: 5˚L ⁄ 45˚R
Weight: 325 lbs.
grizzly.com
201
###
G0513 Series
Generic Labels
G0513 Series
Generic Labels
Model G8588
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material
(7/12/13)
214
203
WARNING!
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
206
INJURY HAZARD!
Do not open door
while machine is
connected to power
or blade is in motion.
WARNING!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
218
G0513 Series
Generic Labels
INJURY HAZARD!
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material
Do not open door
while machine is
connected to power
or blade is in motion.
(7/12/13)
WARNING!
EYE/LUNG INJURY
INJURY/SHOCK
HAZARD!
HAZARD!
Always wear INC.
safety
COPYRIGHT © GRIZZLY INDUSTRIAL,
Disconnect power
glasses and a
adjustments,
before
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE
OR
CHANGE THIS
ARTWORK
respirator
when
maintenance, or
changed without
approval. If
WITHOUT WRITTEN APPROVAL! Grizzly will not accept
usinglabels
this machine.
service.
G0513 Series
Generic Labels
artwork changes are required, contact us immediately at manuals@grizzly.com.
(7/12/13)
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material
208
0513 Series
neric Labels
(7/12/13)
WARNING!
EYE/LUNG INJURY
HAZARD!
Always wear safety
glassesWARNING!
and a
respirator when
To reduce
risk of death
using
this machine.
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
.
WARNING!
WITHOUT
WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. If
To reduce risk ofchanges
death
areINJURY
required,
contact us immediately at manuals@grizzly.com.
HAZARD!
• 1:1artwork
Sizing (Labels
are
or serious injury, read
manual BEFORE using
Do not open door
actual size)
machine.
while machine is
To get a new manual,
connected
• call
Labels
must be made
of to power
(800) 523-4777 or
or blade is in motion.
go
to www.grizzly.commaterial
oil-resistant
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
INJURY HAZARD!
Do not open door
while machine is
connected to power
or blade is in motion.
211
219
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
WARNING!
FOR GRIZZLY
MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
EYE/LUNG
INJURY APPROVAL!
Grizzly will not accept labels changed without approval. If
WITHOUT
WRITTEN
INJURY/SHOCK
HAZARD!
artwork
changes are required,
contact us immediately at manuals@grizzly.com.
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
Disconnect power
before adjustments,
maintenance, or
service.
WARNING!
NING!
k of death
INJURY
HAZARD!
ury, read
ORE
Dousing
not
open door
while
manual, machine is
-4777
or
connected
to power
izzly.com.
or blade is in motion.
RNING!
INJURY
RD!
ar safety
da
when
machine.
INJURY/SHOCK
HAZARD!
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
209
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
210
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
209
Disconnect power
before adjustments,
maintenance, or
service.
215
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
ZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. If
ork changes are required, contact us immediately at manuals@grizzly.com.
G0513 Series
Generic Labels
213
(7/12/13)
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material
203
WARNING!
217
grizzly.com
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
INJURY HAZARD!
Do not open door
while machine is
connected to power
or blade is in motion.
WARNING!
EYE/LUNG INJURY
INJURY/SHOCK
REF PART #
DESCRIPTION
REF
PART #
DESCRIPTION
201
202
203
205
206
208
209
210
MODEL NUMBER LABEL
GRIZZLY LOGO PLATE
OPEN DOOR LABEL
SCALE DIRECTIONS LABEL
SAFETY GLASSES LABEL
READ MANUAL LABEL
ELECTRICITY LABEL
EXTREME SERIES PLATE
211
213
214
215
216V2
217
218
219
P0513X2211
P0513X2213
P0513X2214
P0513X2215
P0513X2216V2
P0513X2217
P0513X2218
P0513X2219
DISCONNECT POWER LABEL
TOUCH-UP PAINT, GRIZZLY PUTTY
TENSION ADJ LABEL
TOUCH-UP PAINT, GRIZZLY GREEN
MACHINE ID LABEL V2.09.18
GRIZZLY.COM LABEL
GUIDE POST ADJUST LABEL
GUIDE POST LOCK LABEL
P0513X2201
P0513X2202
P0513X2203
P0513X2205
P0513X2206
P0513X2208
P0513X2209
P0513X2210
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.
G0513 Series Bandsaws (Mfd. Since 07/18)
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
-87-
G0513X2B Main
71
72
50
55
73
70
74
75
76
11
12
61
48
55A
59
69
49
17
17-3
17-1
22
7
17-2
16
15 14
13
61
38 40
37 41
17-5
22
18-1
21
18-3
30
25 29
28
61
58
18
57
56
97
119
19-2
90
91
61
19-1
92
84
82
83
83
93
94
19-3
19-6V2
111
111
19-9
19-7
63
39
62
87 61
18-2
19-8
19-8
65
64 88
60
18-2
18-3
19
60
18-4
18-5
79
67
66
32 33 34 35 2
24
24
68
80
48
50
46
45
44
31
36
51
3
23
19-5V2
4
47 10
17-4
17-2
21
5
8
81
39
78
95
86
85
84
89
82-4
82-5V2
82-12
176
177
82-11
82-10
82-6
82-2
82-9
82-13
82-14
82-15
82-3
-88-
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
G0513 Series Bandsaws (Mfd. Since 07/18)
G0513X2B Main Parts List
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
2
3
4
5
7
8
10
11
12
13
14
15
16
17
17-1
17-2
17-3
17-4
17-5
18
18-1
18-2
18-3
18-4
18-5
19
19-1
19-2
19-3
19-5V2
19-6V2
19-7
19-8
19-9
21
22
23
24
25
28
29
30
31
32
33
34
35
36
37
38
39
40
P0513X2B002
P0513X2B003
P0513X2B004
P0513X2B005
P0513X2B007
P0513X2B008
P0513X2B010
P0513X2B011
P0513X2B012
P0513X2B013
P0513X2B014
P0513X2B015
P0513X2B016
P0513X2B017
P0513X2B017-1
P0513X2B017-2
P0513X2B017-3
P0513X2B017-4
P0513X2B017-5
P0513X2B018
P0513X2B018-1
P0513X2B018-2
P0513X2B018-3
P0513X2B018-4
P0513X2B018-5
P0513X2B019
P0513X2B019-1
P0513X2B019-2
P0513X2B019-3
P0513X2B019-5V2
P0513X2B019-6V2
P0513X2B019-7
P0513X2B019-8
P0513X2B019-9
P0513X2B021
P0513X2B022
P0513X2B023
P0513X2B024
P0513X2B025
P0513X2B028
P0513X2B029
P0513X2B030
P0513X2B031
P0513X2B032
P0513X2B033
P0513X2B034
P0513X2B035
P0513X2B036
P0513X2B037
P0513X2B038
P0513X2B039
P0513X2B040
SET SCREW M6-1 X 10
BUSHING
LIFTING EYE BOLT M10-1.5
MACHINE BODY
BUSHING
FLAT WASHER 6MM
HEX NUT M6-1
POINTER
STEP SCREW M4-.7 X 5
HINGE SHAFT
ROLL PIN 5 X 35
UPPER WHEEL SHAFT HINGE
UPPER WHEEL SHAFT
UPPER WHEEL ASSEMBLY
BUSHING
BALL BEARING 6204-2RS
INT RETAINING RING 47MM
UPPER WHEEL 17"
URETHANE TIRE 17" 1-PAIR
LOWER WHEEL ASSEMBLY
BUSHING
BALL BEARING 6204-2RS
INT RETAINING RING 47MM
LOWER WHEEL 17"
URETHANE TIRE, 1-PAIR
MAG SWITCH ASSEMBLY MPE-18
MAG SWITCH COVER ASSEMBLY
CONTACTOR SDE MA-18 220V
OL RELAY SDE RA-20 8-12A
PWR CORD 14G 3W 6-15P V2.02.12
CONTROL CORD 16G 5W V2.05.11
MOTOR CORD 14G 5W
PHLP HD SCR M5-.8 X 10
RECTIFIER PU-23-2
WHEEL FLAT WASHER 8MM
CAP SCREW M8-1.25 X 16
SAW BLADE 131.5" X 1/2" 6TPI HOOK
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 20
LOWER WHEEL PULLEY
HEX NUT 1-14
LOCK WASHER 1"
CONTROL PANEL PLATE
COMPRESSION SPRING 7 X 8 X 90
ROLL PIN 3 X 16
ALIGNMENT PLATE
THRUST BEARING 51201
TAP SCREW M4 X 10
TENSION HANDWHEEL
TENSION ADJUSTING ROD
FLANGE SCREW M5-.8 X 10
STOP BUTTON
41
44
45
46
47
48
49
50
51
55A
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
78
79
80
81
82
82-2
82-3
82-4
82-5V2
82-6
82-9
82-10
82-11
82-12
82-13
82-14
82-15
83
84
85
P0513X2B041
P0513X2B044
P0513X2B045
P0513X2B046
P0513X2B047
P0513X2B048
P0513X2B049
P0513X2B050
P0513X2B051
P0513X2B055A
P0513X2B055
P0513X2B056
P0513X2B057
P0513X2B058
P0513X2B059
P0513X2B060
P0513X2B061
P0513X2B062
P0513X2B063
P0513X2B064
P0513X2B065
P0513X2B066
P0513X2B067
P0513X2B068
P0513X2B069
P0513X2B070
P0513X2B071
P0513X2B072
P0513X2B073
P0513X2B074
P0513X2B075
P0513X2B076
P0513X2B078
P0513X2B079
P0513X2B080
P0513X2B081
P0513X2B082
P0513X2B082-2
P0513X2B082-3
P0513X2B082-4
P0513X2B082-5V2
P0513X2B082-6
P0513X2B082-9
P0513X2B082-10
P0513X2B082-11
P0513X2B082-12
P0513X2B082-13
P0513X2B082-14
P0513X2B082-15
P0513X2B083
P0513X2B084
P0513X2B085
START BUTTON
CAP SCREW M8-1.25 X 16
FENDER WASHER 8MM
UPPER WHEEL SLIDING BRACKET
CAP SCREW M6-1 X 25
STEEL BLIND RIVET 3 X 13MM
CAP SCREW M6-1 X 10
CLEAR WINDOW
KEY SWITCH
UPPER WHEEL COVER ASSY
UPPER WHEEL COVER
HEX BOLT M6-1 X 25
FLAT WASHER 6MM
WHEEL BRUSH
CAP SCREW M6-1 X 25
STAR KNOB
LOCK NUT M6-1
STRAIN RELIEF 16MM STRT LT
HEIGHT POINTER
HEX NUT M8-1.25
HEX BOLT M8-1.25 X 90
STAR KNOB BOLT M10-1.5 X 20
STAR KNOB BOLT M10-1.5 X 53
THREADED HANDLE M10-1.5
CAM
PILLOW BLOCK
HANDLE M12-1.75
LEVER
HEX NUT M12-1.75
LEVER HUB
BUTTON HD CAP SCR M8-1.25 X 20
LOCK WASHER 8MM
SHAFT COVER
SET SCREW M8-1.25 X 20
HEX NUT M8-1.25
LOWER WHEEL SHAFT
MOTOR 2HP 220V 1-PH W/BRAKE
MOTOR FAN COVER
MOTOR FAN
CAPACITOR COVER
R CAPACITOR 45M 400V 2 X 2-1/2
MOTOR JUNCTION BOX
MAGNETIC BRAKE YZG
BRAKE SHOE
CAP SCREW M6-1 X 12
LOCK WASHER 6MM
KEY 5 X 5 X 25
BALL BEARING 6203ZZ
BALL BEARING 6205ZZ
HEX BOLT M10-1.5 X 25
LOCK WASHER 10MM
MOTOR MOUNT BRACKET
G0513 Series Bandsaws (Mfd. Since 07/18)
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
-89-
G0513X2B Main Parts List
REF PART #
86
87
88
89
90
91
92
93
DESCRIPTION
REF PART #
P0513X2B086 BUTTON HD CAP SCR M8-1.25 X 20
P0513X2B087 STRAIN RELIEF PLATE 1-HOLE
P0513X2B088 FLANGE SCREW M5-.8 X 10
P0513X2B089 PILLOW BLOCK
P0513X2B090 KEY 5 X 5 X 35
P0513X2B091 KEY 5 X 5 X 35
P0513X2B092 MOTOR PULLEY TYPE-A 3.5"
P0513X2B093 V-BELT A-42
94
95
97
111
119
176
177
DESCRIPTION
P0513X2B094 CAP SCREW M6-1 X 10
P0513X2B095 LOWER WHEEL COVER
P0513X2B097 FENDER WASHER 8MM
P0513X2B111 CAP SCREW M6-1 X 20
P0513X2B119 LOCK WASHER 8MM
P0513X2B176 FLANGE SCREW M5-.8 X 10
P0513X2B177 STRAIN RELIEF 5/16" ELBOW LT
G0513X2B Labels
201
216V2
205
214
202
203
215
204
206
208
209
219
211
218
210
209
212
217
213
REF PART #
DESCRIPTION
REF
PART #
DESCRIPTION
201
202
203
204
205
206
208
209
210
MODEL NUMBER LABEL
GRIZZLY LOGO PLATE
OPEN DOOR LABEL
GUARD ADJ LABEL
SCALE DIRECTIONS LABEL
SAFETY GLASSES LABEL
READ MANUAL LABEL
ELECTRICITY LABEL
EXTREME SERIES PLATE
211
212
213
214
215
216V2
217
218
219
P0513X2B211
P0513X2B212
P0513X2B213
P0513X2B214
P0513X2B215
P0513X2B216V2
P0513X2B217
P0513X2B218
P0513X2B219
DISCONNECT POWER LABEL
OPEN DOOR LABEL
TOUCH-UP PAINT, GRIZZLY PUTTY
TENSION ADJ LABEL
TOUCH-UP PAINT, GRIZZLY GREEN
MACHINE ID LABEL V2.05.11
GRIZZLY.COM LABEL
MAGNETIC BRAKE NOTICE
GUIDE POST LOCK LABEL
P0513X2B201
P0513X2B202
P0513X2B203
P0513X2B204
P0513X2B205
P0513X2B206
P0513X2B208
P0513X2B209
P0513X2B210
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.
-90-
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
G0513 Series Bandsaws (Mfd. Since 07/18)
G0513X2BF Main
174
55
55A
19-6
50
17-3
17-1
22
14
15
16
17-2
13
7
32
33
34
23
17-5
11
36
31
46 51
3 41
38
40
2
35
37
28
30
22
24
18-1
21
18-3
81
67
66
111
58
61
92
119
39
25
18
18-2
78
61
60
29
18-2
18-3
79
80
50
48
60
111
61 65
63
62
39 88
64
87
10
45
44
18-5
61
12
68
18-4
24
95
76
8
17-4
17-2
21
75
4
5
17
48
74
69
19-5
47
73
70
59
19-2
19-4
61
49
72
177
178
175
19-1
19-3
19
71
173
57
56
90
97
94
171
91
93
82-5
82-15
82-4
82-9
85
84
83
172
82
86
82-14
82-6
89
82-2
82-10
82-3
G0513 Series Bandsaws (Mfd. Since 07/18)
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
-91-
G0513X2BF Main Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
2
3
4
5
7
8
10
11
12
13
14
15
16
17
17-1
17-2
17-3
17-4
17-5
18
18-1
18-2
18-3
18-4
18-5
19
19-1
19-2
19-3
19-4
19-5
19-6
21
22
23
24
25
28
29
30
31
32
33
34
35
36
37
38
39
40
41
44
45
SET SCREW M6-1 X 10
BUSHING
LIFTING EYE BOLT M10-1.5
MACHINE BODY
BUSHING
FLAT WASHER 6MM
HEX NUT M6-1
POINTER
STEP SCREW M4-.7 X 5
HINGE SHAFT
ROLL PIN 5 X 35
UPPER WHEEL SHAFT HINGE
UPPER WHEEL SHAFT
UPPER WHEEL ASSEMBLY
BUSHING
BALL BEARING 6204-2RS
INT RETAINING RING 47MM
UPPER WHEEL 17"
URETHANE TIRE 17" 1-PAIR
LOWER WHEEL ASSEMBLY
BUSHING
BALL BEARING 6204-2RS
INT RETAINING RING 47MM
LOWER WHEEL 17"
URETHANE TIRE 17" 1-PAIR
MAG SWITCH ASSY SDE MPE-18 220V
CONTACTOR SDE MA-18 220V
OL RELAY SDE RA-20 8-12A
MAG SWITCH COVER ASSEMBLY
CONTROL CORD 16G 5W V2.05.11
MOTOR CORD 14G 5W
PHLP HD SCR M5-.8 X 10
WHEEL FLAT WASHER 8MM
CAP SCREW M8-1.25 X 16
SAW BLADE 131.5" X 1/2" 6TPI HOOK
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 20
WHEEL PULLEY/BRAKE DRUM
HEX NUT 1-14
LOCK WASHER 1"
CONTROL PANEL PLATE
COMPRESSION SPRING 7 X 8 X 90
ROLL PIN 3 X 16
ALIGNMENT PLATE
THRUST BEARING 51201
TAP SCREW M4 X 10
TENSION HANDWHEEL
TENSION ADJUSTING ROD
FLANGE SCREW M5-.8 X 10
STOP BUTTON
START BUTTON
CAP SCREW M8-1.25 X 16
FENDER WASHER 8MM
46
47
48
49
50
51
55A
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
78
79
80
81
82
82-2
82-3
82-4
82-5
82-6
82-9
82-10
82-14
82-15
83
84
85
86
87
88
89
90
91
92
UPPER WHEEL SLIDING BRACKET
CAP SCREW M6-1 X 25
STEEL BLIND RIVET 3 X 13MM
CAP SCREW M6-1 X 10
CLEAR WINDOW
KEY SWITCH
UPPER WHEEL COVER ASSY
UPPER WHEEL COVER
HEX BOLT M6-1 X 25
FLAT WASHER 6MM
WHEEL BRUSH
CAP SCREW M6-1 X 25
STAR KNOB
LOCK NUT M6-1
STRAIN RELIEF 16MM STRAIGHT LT
HEIGHT POINTER
HEX NUT M8-1.25
HEX BOLT M8-1.25 X 90
STAR KNOB BOLT M10-1.5 X 20
STAR KNOB BOLT M10-1.5 X 53
THREADED HANDLE M10-1.5
CAM
PILLOW BLOCK
HANDLE M12-1.75
LEVER
HEX NUT M12-1.75
LEVER HUB
BUTTON HD CAP SCR M8-1.25 X 20
LOCK WASHER 8MM
SHAFT COVER
SET SCREW M8-1.25 X 20
HEX NUT M8-1.25
LOWER WHEEL SHAFT
MOTOR 2HP 220V 1-PH W/BRAKE
MOTOR FAN COVER
MOTOR FAN
CAPACITOR COVER
R CAPACITOR 45M 450V 2 X 2-1/2
MOTOR JUNCTION BOX
MAGNETIC BRAKE YZG
BRAKE SHOE
BALL BEARING 6205ZZ
BALL BEARING 6203ZZ
HEX BOLT M10-1.5 X 25
LOCK WASHER 10MM
MOTOR MOUNT BRACKET
BUTTON HD CAP SCR M8-1.25 X 20
STRAIN RELIEF PLATE 1-HOLE
TAP SCREW M4 X 10
PILLOW BLOCK
KEY 5 X 5 X 35
HEX BOLT M8-1.25 X 20 LH
MOTOR PULLEY TYPE-A 3.5"
-92-
P0513X2BF002
P0513X2BF003
P0513X2BF004
P0513X2BF005
P0513X2BF007
P0513X2BF008
P0513X2BF010
P0513X2BF011
P0513X2BF012
P0513X2BF013
P0513X2BF014
P0513X2BF015
P0513X2BF016
P0513X2BF017
P0513X2BF017-1
P0513X2BF017-2
P0513X2BF017-3
P0513X2BF017-4
P0513X2BF017-5
P0513X2BF018
P0513X2BF018-1
P0513X2BF018-2
P0513X2BF018-3
P0513X2BF018-4
P0513X2BF018-5
P0513X2BF019
P0513X2BF019-1
P0513X2BF019-2
P0513X2BF019-3
P0513X2BF019-4
P0513X2BF019-5
P0513X2BF019-6
P0513X2BF021
P0513X2BF022
P0513X2BF023
P0513X2BF024
P0513X2BF025
P0513X2BF028
P0513X2BF029
P0513X2BF030
P0513X2BF031
P0513X2BF032
P0513X2BF033
P0513X2BF034
P0513X2BF035
P0513X2BF036
P0513X2BF037
P0513X2BF038
P0513X2BF039
P0513X2BF040
P0513X2BF041
P0513X2BF044
P0513X2BF045
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
P0513X2BF046
P0513X2BF047
P0513X2BF048
P0513X2BF049
P0513X2BF050
P0513X2BF051
P0513X2BF055A
P0513X2BF055
P0513X2BF056
P0513X2BF057
P0513X2BF058
P0513X2BF059
P0513X2BF060
P0513X2BF061
P0513X2BF062
P0513X2BF063
P0513X2BF064
P0513X2BF065
P0513X2BF066
P0513X2BF067
P0513X2BF068
P0513X2BF069
P0513X2BF070
P0513X2BF071
P0513X2BF072
P0513X2BF073
P0513X2BF074
P0513X2BF075
P0513X2BF076
P0513X2BF078
P0513X2BF079
P0513X2BF080
P0513X2BF081
P0513X2BF082
P0513X2BF082-2
P0513X2BF082-3
P0513X2BF082-4
P0513X2BF082-5
P0513X2BF082-6
P0513X2BF082-9
P0513X2BF082-10
P0513X2BF082-14
P0513X2BF082-15
P0513X2BF083
P0513X2BF084
P0513X2BF085
P0513X2BF086
P0513X2BF087
P0513X2BF088
P0513X2BF089
P0513X2BF090
P0513X2BF091
P0513X2BF092
G0513 Series Bandsaws (Mfd. Since 07/18)
G0513X2BF Main Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
93
94
95
97
111
119
171
V-BELT A42
CAP SCREW M6-1 X 10
LOWER WHEEL COVER
FENDER WASHER 8MM
CAP SCREW M6-1 X 20
LOCK WASHER 8MM
FLANGE SCREW M5-.8 X 10
172
173
174
175
177
178
CORD CLIP 5/16"
FLANGE SCREW M5-.8 X 50
PHLP HD SCR M4-.7 X 10
EXT TOOTH WASHER 5MM
JUNCTION BOX
WIRE NUT 14-22G
P0513X2BF093
P0513X2BF094
P0513X2BF095
P0513X2BF097
P0513X2BF111
P0513X2BF119
P0513X2BF171
P0513X2BF172
P0513X2BF173
P0513X2BF174
P0513X2BF175
P0513X2BF177
P0513X2BF178
G0513X2BF Labels
201
216V2
202
214
203
222
204
205
206
208
209
219
207
220
209
215
213
203
209
221
REF PART #
DESCRIPTION
REF
PART #
DESCRIPTION
201
202
203
204
205
206
207
208
209
MODEL NUMBER LABEL
NAMEPLATE-LARGE
DON'T OPEN DOOR LABEL
GUARD ADJUSTMENT LABEL
SCALE DIRECTIONS LABEL
GLASSES/RESPIRATOR LABEL
DISCONNECT POWER LABEL
READ MANUAL LABEL
ELECTRICITY LABEL
213
214
215
216V2
219
220
221
222
P0513X2BF213
P0513X2BF214
P0513X2BF215
P0513X2BF216V2
P0513X2BF219
P0513X2BF220
P0513X2BF221
P0513X2BF222
TOUCH-UP PAINT, GRIZZLY PUTTY
TENSION ADJ LABEL
TOUCH-UP PAINT, GRIZZLY GREEN
MACHINE ID LABEL V2.10.18
MAGNETIC BRAKE LABEL
EXTREME SERIES PLATE
GRIZZLY.COM LABEL
GUIDE POST LOCK LABEL
P0513X2BF201
P0513X2BF202
P0513X2BF203
P0513X2BF204
P0513X2BF205
P0513X2BF206
P0513X2BF207
P0513X2BF208
P0513X2BF209
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.
G0513 Series Bandsaws (Mfd. Since 07/18)
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
-93-
G0513X2F Main
244
(110V)
196
242
(220V)
244-1
244-3
200
197
198
55A
244-2
69
61
48
17-1
22
13
14
15
16
17-2
47
10 12
7
32
23
33
34
17-5
35
11
66
48
61
65
64
50 60
111
63
62
39 88
61
18-4
24
91
28
22
24
21
18-3
81
90
119
92
18-2
18-3
18-1
78 39
60
111
30
18-5
79 80
87
37
25
29
2
67
8
45
43
44 190
46 193
3
38 194
195
17-4
17-2
21
74
68
17
17-3
70
59
4
94
49
242-5
72
73
76 75
5
61
242-4
71
242-5
55
50
242-2
243
199
243 242-4
95
242-1
242-3
61
93
58
18
57
97
56
18-2
188
189
82-8A
82-4
82-1
82-2
82-3
82
82-5
82-6
-94-
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
82-7 82-8
82-10
82-9
86
89
83
85
84
G0513 Series Bandsaws (Mfd. Since 07/18)
G0513X2F Main Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
2
3
4
5
7
8
10
11
12
13
14
15
16
17
17-1
17-2
17-3
17-4
17-5
18
18-1
18-2
18-3
18-4
18-5
21
22
23
24
25
28
29
30
32
33
34
35
37
38
39
43
44
45
46
47
48
49
50
55A
55
56
57
58
SET SCREW M6-1 X 10
BUSHING
LIFTING EYE BOLT M10-1.5
MACHINE BODY
BUSHING
FLAT WASHER 6MM
HEX NUT M6-1
POINTER
STEP SCREW M4-.7 X 5
HINGE SHAFT
ROLL PIN 5 X 36
UPPER WHEEL SHAFT HINGE
UPPER WHEEL SHAFT
UPPER WHEEL ASSEMBLY
BUSHING
BALL BEARING 6204-2RS
INT RETAINING RING 47MM
UPPER WHEEL 17"
URETHANE TIRE 17" 1-PAIR
LOWER WHEEL ASSEMBLY
BUSHING
BALL BEARING 6204-2RS
INT RETAINING RING 47MM
LOWER WHEEL 17"
URETHANE TIRE, 1-PAIR
WHEEL FLAT WASHER 8MM
CAP SCREW M8-1.25 X 16
SAW BLADE 131.5" X 1/2" 6TPI HOOK
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 20
WHEEL PULLEY/BRAKE DRUM
HEX NUT 1-14
LOCK WASHER 1"
COMPRESSION SPRING 7 X 8 X 90
ROLL PIN 3 X 16
ALIGNMENT PLATE
THRUST BEARING 51201
TENSION HANDWHEEL
TENSION ADJUSTING ROD
FLANGE SCREW M5-.8 X 10
CONTROL PANEL PLATE
CAP SCREW M8-1.25 X 16
FENDER WASHER 8MM
UPPER WHEEL SLIDING BRACKET
CAP SCREW M8-1.25 X 50
STEEL BLIND RIVET 3 X 13MM
CAP SCREW M6-1 X 10
CLEAR WINDOW
UPPER WHEEL COVER ASSY
UPPER WHEEL COVER
HEX BOLT M6-1 X 25
FLAT WASHER 6MM
WHEEL BRUSH
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
78
79
80
81
82
82-1
82-2
82-3
82-4
82-5
82-6
82-7
82-8A
82-8
82-9
82-10
83
84
85
86
87
88
89
90
91
92
93
94
95
97
111
119
188
189
190
CAP SCREW M6-1 X 25
STAR KNOB
LOCK NUT M6-1
STRAIN RELIEF 16MM STRAIGHT LT
HEIGHT POINTER
HEX NUT M8-1.25
HEX BOLT M8-1.25 X 90
STAR KNOB BOLT M10-1.5 X 20
STAR KNOB BOLT M10-1.5 X 55
THREADED HANDLE M10-1.5
CAM
PILLOW BLOCK
HANDLE M12-1.75
LEVER
HEX NUT M12-1.75
LEVER HUB
BUTTON HD CAP SCR M8-125 X 20
LOCK WASHER 8MM
SHAFT COVER
SET SCREW M8-1.25 X 20
HEX NUT M8-1.25
LOWER WHEEL SHAFT
MOTOR 2HP 110V/220V 1-PH
MOTOR FAN COVER
MOTOR FAN
CAPACITOR COVER
R CAPACITOR 40M 250V 1-3/8 X 2-5/8
MOTOR JUNCTION BOX
S CAPACITOR 300M 250V 1-1/2 X 2-3/8
CONTACT PLATE 5/8
CENTRIFUGAL SWITH W/CONT PLATE
CENTRIFUGAL SWITCH 5/8-1725
BALL BEARING 6205ZZ
BALL BEARING 6203ZZ
HEX BOLT M10-1.5 X 25
LOCK WASHER 10MM
MOTOR MOUNT BRACKET
BUTTON HD CAP SCR M8-125 X 20
STRAIN RELIEF PLATE 1-HOLE
FLANGE SCREW M5-.8 X 10
PILLOW BLOCK
KEY 5 X 5 X 35
HEX BOLT M8-1.25 X 20 LH
MOTOR PULLEY TYPE-A 3.5"
V-BELT A42
CAP SCREW M6-1 X 10
LOWER WHEEL COVER
FENDER WASHER 8MM
CAP SCREW M6-1 X 20
FLAT WASHER 4MM
FLANGE SCREW M5-.8 X 10
CORD CLIP 5/16"
TAP SCREW M4 X 10
P0513X2F002
P0513X2F003
P0513X2F004
P0513X2F005
P0513X2F007
P0513X2F008
P0513X2F010
P0513X2F011
P0513X2F012
P0513X2F013
P0513X2F014
P0513X2F015
P0513X2F016
P0513X2F017
P0513X2F017-1
P0513X2F017-2
P0513X2F017-3
P0513X2F017-4
P0513X2F017-5
P0513X2F018
P0513X2F018-1
P0513X2F018-2
P0513X2F018-3
P0513X2F018-4
P0513X2F018-5
P0513X2F021
P0513X2F022
P0513X2F023
P0513X2F024
P0513X2F025
P0513X2F028
P0513X2F029
P0513X2F030
P0513X2F032
P0513X2F033
P0513X2F034
P0513X2F035
P0513X2F037
P0513X2F038
P0513X2F039
P0513X2F043
P0513X2F044
P0513X2F045
P0513X2F046
P0513X2F047
P0513X2F048
P0513X2F049
P0513X2F050
P0513X2F055A
P0513X2F055
P0513X2F056
P0513X2F057
P0513X2F058
G0513 Series Bandsaws (Mfd. Since 07/18)
P0513X2F059
P0513X2F060
P0513X2F061
P0513X2F062
P0513X2F063
P0513X2F064
P0513X2F065
P0513X2F066
P0513X2F067
P0513X2F068
P0513X2F069
P0513X2F070
P0513X2F071
P0513X2F072
P0513X2F073
P0513X2F074
P0513X2F075
P0513X2F076
P0513X2F078
P0513X2F079
P0513X2F080
P0513X2F081
P0513X2F082
P0513X2F082-1
P0513X2F082-2
P0513X2F082-3
P0513X2F082-4
P0513X2F082-5
P0513X2F082-6
P0513X2F082-7
P0513X2F082-8A
P0513X2F082-8
P0513X2F082-9
P0513X2F082-10
P0513X2F083
P0513X2F084
P0513X2F085
P0513X2F086
P0513X2F087
P0513X2F088
P0513X2F089
P0513X2F090
P0513X2F091
P0513X2F092
P0513X2F093
P0513X2F094
P0513X2F095
P0513X2F097
P0513X2F111
P0513X2F119
P0513X2F188
P0513X2F189
P0513X2F190
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
-95-
G0513X2F Main Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
193
194
195
196
197
198
199
200
242
242-1
KEY SWITCH
START BUTTON
STOP BUTTON
FLANGE SCREW M5-.8 X 50
JUNCTION BOX
WIRE NUT 14-22G
EXT TOOTH WASHER 5MM
PHLP HD SCR M4-.7 X 10
MAG SWITCH ASSY 220V MPE-09
CONTACTOR SDE MA-09 220-240V
242-2
242-3
242-4
242-5
243
244
244-1
244-2
244-3
OL RELAY SDE RA-20 8-12A
MAG SWITCH COVER ASSEMBLY
CONTROL CORD 16G 3W
MOTOR CORD 14G 3W
PHLP HD SCR M5-.8 X 10
MAG SWITCH ASSY 110V MPE-18
CONTACTOR SDE MA-18 110V
OL RELAY SDE RA-30 18-26A
MAG SWITCH COVER ASSEMBLY
P0513X2F193
P0513X2F194
P0513X2F195
P0513X2F196
P0513X2F197
P0513X2F198
P0513X2F199
P0513X2F200
P0513X2F242
P0513X2F242-1
P0513X2F242-2
P0513X2F242-3
P0513X2F242-4
P0513X2F242-5
P0513X2F243
P0513X2F244
P0513X2F244-1
P0513X2F244-2
P0513X2F244-3
G0513X2F Labels
201
214
202
216V2
205
203
204
249
206
208
211
209
210
215
209
203
213
209
248
REF PART #
DESCRIPTION
REF
PART #
DESCRIPTION
201
202
203
204
205
206
208
209
MODEL NUMBER LABEL
GRIZZLY NAMEPLATE- LARGE
DON'T OPEN DOOR LABEL
GUARD ADJUSTMENT LABEL
SCALE DIRECTIONS LABEL
GLASSES/RESPIRATOR LABEL
READ MANUAL LABEL
ELECTRICITY LABEL
210
211
213
214
215
216V2
248
249
P0513X2F210
P0513X2F211
P0513X2F213
P0513X2F214
P0513X2F215
P0513X2F216V2
P0513X2F248
P0513X2F249
EXTREME SERIES NAMEPLATE
DISCONNECT POWER LABEL
TOUCH-UP PAINT, GRIZZLY PUTTY
TENSION ADJUSTMENT LABEL
TOUCH-UP PAINT, GRIZZLY GREEN
MACHINE ID LABEL V2.10.18
GRIZZLY.COM LABEL
GUIDEPOST LOCK LABEL
P0513X2F201
P0513X2F202
P0513X2F203
P0513X2F204
P0513X2F205
P0513X2F206
P0513X2F208
P0513X2F209
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.
-96-
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
G0513 Series Bandsaws (Mfd. Since 07/18)
G0513X2, G0513X2B, G0513X2BF &
G0513X2F Guides & Trunnions
151
353
352
354
145-18
145-11
151-7
145-10
145-12
145-13
145-14
151-5
151-6
145
145-8
145-7
151-10 151-8
151-9
151-11
145-1
356
357
140
145-2
145-4
145-5
141
146
145-6
145-9
145-16
145-17
355
147
145-15
145-3
142
136
137
138
150-3
150-8
150-7
150-11
150-2
150-5
150-1
150-4
150-6
155-8
155-7
155-1
155-9
155-16
155-1
155-2
150-9
150-10 150-8
150
155
155-10
155-3
155-11
155-4
155-31
155-5
155-6
155-23
155-12 155-1 155-13
155-14
155-15
155-3
155-17
155-18
155-19
155-20V2
155-24
155-33
155-30
155-29
155-28
155-27
155-26
155-1
155-2
155-32
155-21
155-22
139V2
103
104
155-25
104
98
G0513 Series Bandsaws (Mfd. Since 07/18)
103
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
-97-
G0513X2, G0513X2B, G0513X2BF &
G0513X2F Guides & Trunnions Parts List
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
98
103
104
136
137
138
139V2
140
141
142
145
145-1
145-2
145-3
145-4
145-5
145-6
145-7
145-8
145-9
145-10
145-11
145-12
145-13
145-14
145-15
145-16
145-17
145-18
146
147
150
150-1
150-2
150-3
150-4
150-5
150-6
150-7
150-8
150-9
150-10
150-11
151
151-5
151-6
P0513X2098
P0513X2103
P0513X2104
P0513X2136
P0513X2137
P0513X2138
P0513X2139V2
P0513X2140
P0513X2141
P0513X2142
P0513X2145
P0513X2145-1
P0513X2145-2
P0513X2145-3
P0513X2145-4
P0513X2145-5
P0513X2145-6
P0513X2145-7
P0513X2145-8
P0513X2145-9
P0513X2145-10
P0513X2145-11
P0513X2145-12
P0513X2145-13
P0513X2145-14
P0513X2145-15
P0513X2145-16
P0513X2145-17
P0513X2145-18
P0513X2146
P0513X2147
P0513X2150
P0513X2150-1
P0513X2150-2
P0513X2150-3
P0513X2150-4
P0513X2150-5
P0513X2150-6
P0513X2150-7
P0513X2150-8
P0513X2150-9
P0513X2150-10
P0513X2150-11
P0513X2151
P0513X2151-5
P0513X2151-6
CAP SCREW M10-1.5 X 35
LOCK WASHER 10MM
FLAT WASHER 10MM
CAP SCREW M5-.8 X 10
FLAT WASHER 5MM
UPPER BLADE GUARD
CAP SCREW M10-1.5 X 35
STEP SCREW M4-.7 X 5
FIBER WASHER 5MM
SLIDING PLATE
GUIDE POST ASSEMBLY
SET SCREW M5-.8 X 5
CAP SCREW M6-1 X 16
PHLP HD SCR M4-.7 X 10
HEX NUT M4-.7
RACK
GUIDE POST
LOCK COLLAR
THREADED BUSHING V2.06.09
LOCK WASHER 8MM
THREADED GUIDE BRACKET 14MM V2.06.09
WORM CYLINDER
FIXED PLATE
PINION GEAR 15T
PINION GEAR STEP BOLT
BRACKET COVER
CAP SCREW M8-1.25 X 16
FLAT HD SCR M4-.7 X 8
BUSHING
GUIDE POST HANDWHEEL
CAP SCREW M6-1 X 20
UPPER BLADE GUIDE ASSEMBLY
CAP SCREW M6-1 X 16
UPPER GUIDE SUPPORT BLOCK
SET SCREW M6-1 X 10
ADJUSTMENT BAR
UPPER BLADE GUIDE SUPPORT
ECCENTRIC SHAFT
EXT RETAINING RING 15MM
BALL BEARING 6202ZZ
HANDLE BUSHING
CAP SCREW M6-1 X 35
UPPER SPACING SHAFT
LOWER BLADE GUIDE ASSEMBLY
LOWER BLADE GUIDE SUPPORT
CAP SCREW M6-1 X 16
151-7
151-8
151-9
151-10
151-11
155
155-1
155-2
155-3
155-4
155-5
155-6
155-7
155-8
155-9
155-10
155-11
155-12
155-13
155-14
155-15
155-16
155-17
155-18
155-19
155-20V2
155-21
155-22
155-23
155-24
155-25
155-26
155-27
155-28
155-29
155-30
155-31
155-32
155-33
352
353
354
355
356
357
P0513X2151-7
P0513X2151-8
P0513X2151-9
P0513X2151-10
P0513X2151-11
P0513X2155
P0513X2155-1
P0513X2155-2
P0513X2155-3
P0513X2155-4
P0513X2155-5
P0513X2155-6
P0513X2155-7
P0513X2155-8
P0513X2155-9
P0513X2155-10
P0513X2155-11
P0513X2155-12
P0513X2155-13
P0513X2155-14
P0513X2155-15
P0513X2155-16
P0513X2155-17
P0513X2155-18
P0513X2155-19
P0513X2155-20V2
P0513X2155-21
P0513X2155-22
P0513X2155-23
P0513X2155-24
P0513X2155-25
P0513X2155-26
P0513X2155-27
P0513X2155-28
P0513X2155-29
P0513X2155-30
P0513X2155-31
P0513X2155-32
P0513X2155-33
P0513X2352
P0513X2353
P0513X2354
P0513X2355
P0513X2356
P0513X2357
ECCENTRIC SHAFT
EXT RETAINING RING 15MM
BALL BEARING 6202ZZ
HANDLE BUSHING
CAP SCREW M6-1 X 35
CAST IRON TRUNNION ASSEMBLY
FLAT WASHER 8MM
LOCK NUT M8-1.25
PHLP HD SCR M4-.7 x 6
GEAR PLATE
FLAT HD SCR M4-.7 X 6
CARRIAGE BOLT M8-1.25 X 85
CAST IRON TRUNNION
CARRIAGE BOLT M8-1.25 X 80
LOCK HANDLE M8-1.25
TABLE TILT SCALE
FLAT WASHER 8MM
HEX BOLT M8-1.25 X 25
LOCK HANDLE M8-1.25
FLAT WASHER 4MM
POINTER
LOCK WASHER 8MM
ADJUSTMENT KNOB BOLT M6-1
HEX NUT M6-1
L-BRACKET
FLAT HD SCR M5-.8 X 8
CAP SCREW M6-1 X 16
CAP SCREW M6-1 X 50
TRUNNION SUPPORT BRACKET
TRUNNION GEAR
BUTTON HD CAP SCR M10-1.5 X 30
RIGHT GUARD
BALL BEARING 6000ZZ
FLAT WASHER 10MM
LEFT GUARD
ADJUSTMENT ROD
LOCK WASHER 8MM
CAP SCREW M5-.8 X 6
LOCK WASHER 10MM
FLAT WASHER 8MM
LOCK WASHER 8MM
BUTTON HD CAP SCR M8-1.25 X 20
HEX WRENCH 5MM
HEX WRENCH 8MM
WRENCH 10 X 13 OPEN-END
-98-
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
G0513 Series Bandsaws (Mfd. Since 07/18)
G0513X2 & G0513X2F Fence Assembly & Table
350-3
350-2
152
121-24
127
126
350
350-1
128
121-18
121-14
121
121-19
121-11
121-12
121-16
121-4
121-2
121-13
121-15
121-9
121-22
121-10
121-7
121-6
121-3
121-8
121-29
121-27 121-23
121-25
121-26
121-5
121-21
121-1
121-17
121-20
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
121
121-1
121-2
121-3
121-4
121-5
121-6
121-7
121-8
121-9
121-10
121-11
121-12
121-13
121-14
121-15
121-16
121-17
121-18
P0513X2121
P0513X2121-1
P0513X2121-2
P0513X2121-3
P0513X2121-4
P0513X2121-5
P0513X2121-6
P0513X2121-7
P0513X2121-8
P0513X2121-9
P0513X2121-10
P0513X2121-11
P0513X2121-12
P0513X2121-13
P0513X2121-14
P0513X2121-15
P0513X2121-16
P0513X2121-17
P0513X2121-18
FENCE ASSEMBLY
FRONT RAIL 640MM
ADJUST BASE
FIXED SHAFT
SHAFT
SPRING PIECE
LOCKING HANDLE M8-1.25 X 44
CAST IRON FENCE 590MM
FLAT WASHER 8MM
FENCE HANDLE M8-1.25 X 22
RAIL PAD
CONVEX WINDOW
CAP SCREW M6-1 X 24
LOCK BLOCK
REAR RAIL 640MM
HEX NUT M8-1.25
FLANGE SCREW M4-.7 X 6
GUARD PIECE
MOVING PLATE
121-19
121-20
121-21
121-22
121-23
121-24
121-25
121-26
121-27
121-29
126
127
128
152
350
350-1
350-2
350-3
P0513X2121-19
P0513X2121-20
P0513X2121-21
P0513X2121-22
P0513X2121-23
P0513X2121-24
P0513X2121-25
P0513X2121-26
P0513X2121-27
P0513X2121-29
P0513X2126
P0513X2127
P0513X2128
P0513X2152
P0513X2350
P0513X2350-1
P0513X2350-2
P0513X2350-3
PLUG
TAP SCREW M3.5 X 8
FENCE SCALE 18-1/2"
HEX NUT M6-1
LOCK WASHER 6MM
CAP SCREW M6-1 X 16
HEX BOLT M6-1 X 20
FLANGE BOLT M4-.7 X 8
FLAT WASHER 6MM
SPACER PLATE
TABLE 17" X 24"
TABLE INSERT
TABLE PIN
MITER GAUGE ASSY
RESAW FENCE ASSEMBLY
ALUMINUM RESAW FENCE 590MM
TAP SCREW 3.5 X 8
FENCE END PLATE 148 X 22 X 1
G0513 Series Bandsaws (Mfd. Since 07/18)
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
-99-
G0513X2B & G0513X2BF Fence Assembly &
Table
157
157-14V2
157-15
157-17V2
157-16
157-12
157-1
157-18
157-13
157-3V2
157-10
157-6
157-7
157-8
127
157-11
157-2 157-16
157-4
157-5
161-1
157-9 157-13
128
161
162
156-3
156
154
163
164
156-2
152
126
165V2
156-1
158
153
160
159
158
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
126
127
128
152
153
154
156
156-1
156-2
156-3
157
157-1
157-2
157-3V2
157-4
157-5
157-6
157-7
157-8
P0513X2B126
P0513X2B127
P0513X2B128
P0513X2B152
P0513X2B153
P0513X2B154
P0513X2B156
P0513X2B156-1
P0513X2B156-2
P0513X2B156-3
P0513X2B157
P0513X2B157-1
P0513X2B157-2
P0513X2B157-3V2
P0513X2B157-4
P0513X2B157-5
P0513X2B157-6
P0513X2B157-7
P0513X2B157-8
TABLE 17" X 24"
TABLE INSERT
TABLE PIN
MITER GAUGE ASSY
KNOB SCREW M8-1.25 X 20
OUTER RAIL PLATE
RESAW FENCE ASSEMBLY
ALUMINUM RESAW FENCE 590MM
TAP SCREW 3.5 X 8
FENCE END PLATE 148 X 22 X 1
FENCE ASSEMBLY
FENCE
POINTER
SET SCREW M8-1.25 X 25
SPRING PIECE
FLANGE SCREW M4-.7 X 8
PIVOT BLOCK
HEX NUT M8-1.25
FENCE LOCK HANDLE
157-9
157-10
157-11
157-12
157-13
157-14V2
157-15
157-16
157-17V2
157-18
158
159
160
161
161-1
162
163
164
165V2
P0513X2B157-9
P0513X2B157-10
P0513X2B157-11
P0513X2B157-12
P0513X2B157-13
P0513X2B157-14V2
P0513X2B157-15
P0513X2B157-16
P0513X2B157-17V2
P0513X2B157-18
P0513X2B158
P0513X2B159
P0513X2B160
P0513X2B161
P0513X2B161-1
P0513X2B162
P0513X2B163
P0513X2B164
P0513X2B165V2
SHAFT
PLASTIC SET SCREW M7-1 X 10
NYLON PAD
SET SCREW M8-1.25 X 12
HEX NUT M8-1.25
HEX BOLT M8-1.25 X 20
HEX NUT M8-1.25
FLAT WASHER 8MM
LOCK HANDLE M8-1.25 X 45 V2.05.11
MOVING PLATE
FLAT WASHER 8MM
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 20
FRONT RAIL
FENCE SCALE
INNER RAIL PLATE
FLAT WASHER 6MM
LOCK WASHER 6MM
CAP SCREW M6-1 X 20
-100-
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
G0513 Series Bandsaws (Mfd. Since 07/18)
G0513X2BF & G0513X2F Foot Brake
326
325
324
304 305
309
303
306
307
302
308
310
311
312
313
314
301
317
323
322
321
320
316
315
317 318
317
319
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
301
302
303
304
305
306
307
308
309
310
311
312
313
CONDUIT GROMMET
FLEXIBLE CONDUIT 1/2" X 42"
SWITCH CORD 16G 2W
HEX NUT 4MM
BRAKE SWITCH SHINOZAKI AZ7141
PHLP HD SCR M4-.7 X 30
CORD CLIP 5/8"
TAP SCREW M4 X 8
BUSHING
FLAT WASHER 8MM
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 25
CAP SCREW M6-1 X 25
314
315
316
317
318
319
320
321
322
323
324
325
326
LOCK WASHER 6MM
BRAKE SHOE
BUSHING
CAP SCREW M6-1 X 16
HEX NUT M6-1
LOCK WASHER 6MM
BRAKE PEDDLE
NYLON PAD
BRAKE EXTENSION SPRING
HEX NUT M6-1
STEP BOLT M7-1 X 10 W/BUSHING
BRAKE LEVER
RUBBER CLIP
P0513X2F301
P0513X2F302
P0513X2F303
P0513X2F304
P0513X2F305
P0513X2F306
P0513X2F307
P0513X2F308
P0513X2F309
P0513X2F310
P0513X2F311
P0513X2F312
P0513X2F313
G0513 Series Bandsaws (Mfd. Since 07/18)
P0513X2F314
P0513X2F315
P0513X2F316
P0513X2F317
P0513X2F318
P0513X2F319
P0513X2F320
P0513X2F321
P0513X2F322
P0513X2F323
P0513X2F324
P0513X2F325
P0513X2F326
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
-101-
-102-
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
G0513 Series Bandsaws (Mfd. Since 07/18)
WARRANTY CARD
Name _____________________________________________________________________________
Street _____________________________________________________________________________
City _______________________ State _________________________ Zip _____________________
Phone # ____________________ Email _________________________________________________
Model # ____________________ Order # _______________________ Serial # __________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop
better products and services. Of course, all information is strictly confidential.
1.
CUT ALONG DOTTED LINE
2.
How did you learn about us?
____ Advertisement
____ Card Deck
4.
5.
6.
____ Catalog
____ Other:
Which of the following magazines do you subscribe to?
____
____
____
____
____
____
____
____
____
____
3.
____ Friend
____ Website
Cabinetmaker & FDM
Family Handyman
Hand Loader
Handy
Home Shop Machinist
Journal of Light Cont.
Live Steam
Model Airplane News
Old House Journal
Popular Mechanics
____
____
____
____
____
____
____
____
____
____
Popular Science
Popular Woodworking
Precision Shooter
Projects in Metal
RC Modeler
Rifle
Shop Notes
Shotgun News
Today’s Homeowner
Wood
____
____
____
____
____
____
____
Wooden Boat
Woodshop News
Woodsmith
Woodwork
Woodworker West
Woodworker’s Journal
Other:
What is your annual household income?
____ $20,000-$29,000
____ $30,000-$39,000
____ $50,000-$59,000
____ $60,000-$69,000
____ $40,000-$49,000
____ $70,000+
What is your age group?
____ 20-29
____ 50-59
____ 40-49
____ 70+
____ 30-39
____ 60-69
How long have you been a woodworker/metalworker?
____ 0-2 Years
____ 2-8 Years
____ 8-20 Years
____ 20+ Years
How many of your machines or tools are Grizzly?
____ 0-2
____ 3-5
____ 6-9
____ 10+
7.
Do you think your machine represents a good value?
_____ Yes
_____No
8.
Would you recommend Grizzly Industrial to a friend?
_____ Yes
_____No
9.
Would you allow us to use your name as a reference for Grizzly customers in your area?
Note: We never use names more than 3 times.
_____ Yes
_____No
10. Comments: _____________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
WARRANTY & RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue
you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the carton. We
will not accept any item back without this number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement