Grizzly G0673 10 HP Industrial Dust Collector Owner Manual

Grizzly G0673 10 HP Industrial Dust Collector Owner Manual

MODEL G0671/G0672/G0673 DUST COLLECTOR

OWNER'S MANUAL

(For models manufactured since 6/17)

G0671 4 HP 220V Single-Phase G0672 5 HP 220V Single-Phase G0673 10 HP 220/440V 3-Phase

COPYRIGHT © MAY, 2008 BY GRIZZLY INDUSTRIAL, INC. REVISED NOVEMBER, 2017 (HE)

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#BLJB10749 PRINTED IN TAIWAN V4.11.17

This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use. This responsibility includes but is not limited to proper installation in a safe environment, personnel training and usage authorization, proper inspection and maintenance, manual availability and compre hension, application of safety devices, cutting/sanding/grinding tool integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property damage from negligence, improper training, machine modifications or misuse.

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: Work in a well ventilated area, and work with approved safety equip ment, such as those dust masks that are specially designed to filter out microscopic particles.

Table of Contents

INTRODUCTION ............................................... 2

Machine Description ...................................... 2 Contact Info.................................................... 2 Manual Accuracy ........................................... 2

Identification ................................................... 3

G0671 Machine Data Sheet .......................... 4

G0672 Machine Data Sheet .......................... 7

G0673 Machine Data Sheet ........................ 10

SECTION 1: SAFETY ..................................... 13

Safety Instructions for Machinery ................ 13

SECTION 2: POWER SUPPLY ...................... 16

G0673 440V Conversion ............................. 18

SECTION 3: SETUP ....................................... 19

Needed for Setup ......................................... 19 Unpacking .................................................... 19

G0671/G0672 Inventory............................... 20

G0673 Inventory .......................................... 21

Site Considerations ...................................... 22

Assembly ..................................................... 23

Test Run ...................................................... 26

SECTION 4: DESIGNING THE SYSTEM ....... 27

General ........................................................ 27 Duct Material ................................................ 27

System Design ............................................. 29

System Grounding ....................................... 34

SECTION 5: OPERATIONS ........................... 35

Basic Controls .............................................. 35 General ........................................................ 35

SECTION 6: ACCESSORIES ......................... 36

SECTION 7: MAINTENANCE ......................... 39

Schedule ...................................................... 39 Lubrication ................................................... 39 Bag Cleaning ............................................... 39

SECTION 8: SERVICE ................................... 40

Troubleshooting ........................................... 40

SECTION 9: WIRING ...................................... 42

Wiring Safety Instructions ............................ 42

G0671 Wiring Diagram ................................ 43

G0672 Wiring Diagram ................................ 44

G0673 Wiring Diagram ................................ 45

G0673 Electrical Components ..................... 46

SECTION 10: PARTS ..................................... 47

G0671 Parts Breakdown .............................. 47

G0672 Parts Breakdown .............................. 49

G0673 Parts Breakdown .............................. 51

Label Placement .......................................... 53

WARRANTY AND RETURNS ........................ 57

INTRODUCTION Machine Description

This machine is designed to capture dust and wood chips from multiple woodworking machines at the same time, such as table saws, jointers, and planers. A wide variety of accessories for setting up a stationary or mobile dust collection system are available through Grizzly.

Contact Info

We stand behind our machines! If you have ques tions or need help, contact us with the information below. Before contacting, make sure you get the serial number and manufacture date from the machine ID label. This will help us help you faster.

Grizzly Technical Support 1815 W. Battlefield Springfield, MO 65807 Phone: (570) 546-9663 Email: techsupport@grizzly.com

We want your feedback on this manual. What did you like about it? Where could it be improved? Please take a few minutes to give us feedback.

Grizzly Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 Email: manuals@grizzly.com

Manual Accuracy

We are proud to provide a high-quality owner’s manual with your new machine!

We made every effort to be exact with the instruc tions, specifications, drawings, and photographs in this manual. Sometimes we make mistakes, but our policy of continuous improvement also means that

sometimes the machine you receive is

slightly different than shown in the manual.

If you find this to be the case, and the difference between the manual and machine leaves you confused or unsure about something, check our website for an updated version. We post current manuals and manual updates for free on our web site at www.grizzly.com.

Alternatively, you can call our Technical Support for help. Before calling, make sure you write down the Manufacture Date and Serial Number from the machine ID label (see below). This information is required for us to provide proper tech support, and it helps us determine if updated documenta tion is available for your machine.

Manufacture Date Serial Number -2 Model G0671/G0672/G0673 (Mfd. Since 6/17)

Upper Bag

Identification

Upper Bag Hanger Assembly Collector Collection Bag Model G0671/G0672/G0673 (Mfd. Since 6/17) Caster

To reduce your risk of serious injury, read this entire manual BEFORE using machine.

Inlet ON/OFF Power Switch Motor (Hidden From View) Base -3-

MACHINE DATA SHEET

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

MODEL G0671 4 HP DUST COLLECTOR Product Dimensions:

Weight.............................................................................................................................................................. 270 lbs.

Width (side-to-side) x Depth (front-to-back) x Height...................................................... 73-7/8 x 31-3/8 x 101-1/8 in.

Footprint (Length x Width)............................................................................................................... 73-7/8 x 31-3/8 in.

Shipping Dimensions:

Type............................................................................................................................ Cardboard Box & Wood Frame Content........................................................................................................................................................... Machine Weight.............................................................................................................................................................. 306 lbs.

Length x Width x Height....................................................................................................................... 42 x 29 x 30 in.

Must Ship Upright................................................................................................................................................... Yes

Electrical:

Power Requirement........................................................................................................... 220V, Single-Phase, 60 Hz Prewired Voltage.................................................................................................................................................. 220V Full-Load Current Rating........................................................................................................................................ 26A Minimum Circuit Size.............................................................................................................................................. 40A Connection Type........................................................................................... Permanent (Hardwire to Shutoff Switch) Power Cord Included.............................................................................................................................................. Yes Plug Included........................................................................................................................................................... No Switch Type.................................................................................................... Magnetic Switch w/Overload Protection

Motors: Main

Horsepower................................................................................................................................................ 4 HP Phase............................................................................................................................................ Single-Phase Amps............................................................................................................................................................ 26A Speed................................................................................................................................................ 3450 RPM Type................................................................................................................. TEFC Capacitor-Start Induction Power Transfer ............................................................................................................................... Direct Drive Bearings..................................................................................................... Shielded & Permanently Lubricated

Main Specifications: Operation

Dust Collector Type....................................................................................................................... Single-Stage Approved Dust Types................................................................................................................................ Wood Filter Type.................................................................................................................................................... Bag Airflow Performance......................................................................................................................... 3552 CFM Max Static Pressure (at 0 CFM)............................................................................................................. 13.5 in.

Main Inlet Size........................................................................................................................................... 10 in.

Inlet Adapter Included.................................................................................................................................. Yes Number of Adapter Inlets.................................................................................................................................. 4 Adapter Inlet Size........................................................................................................................................ 4 in.

Machine Collection Capacity At One Time....................................................................................................... 3 Maximum Material Collection Capacity................................................................................................. 24 cu. ft.

Filtration Rating.................................................................................................................................. 2.5 Micron

Model G0671

-4-

PAGE 1 OF 2

Model G0671/G0672/G0673 (Mfd. Since 6/17)

Bag Information

Number of Upper Bags..................................................................................................................................... 2 Number of Lower Bags..................................................................................................................................... 2 Upper Bag Diameter............................................................................................................................ 23-5/8 in.

Upper Bag Length............................................................................................................................... 47-1/4 in.

Lower Bag Diameter............................................................................................................................ 23-5/8 in.

Lower Bag Length...................................................................................................................................... 54 in.

Impeller Information

Impeller Type...................................................................................................................................... Radial Fin Impeller Size........................................................................................................................................ 14-1/2 in.

Impeller Blade Thickness.......................................................................................................................... 1/4 in.

Construction

Upper Bag................................................................................................................................................ Fabric Lower Bag................................................................................................................................................ Plastic Frame.................................................................................................................... Steel Sheet Metal w/Casters Impeller....................................................................................................................................................... Steel Paint Type/Finish....................................................................................................................... Powder Coated Body....................................................................................................................................... Steel Sheet Metal

Other Specifications:

Country of Origin .............................................................................................................................................. Taiwan Warranty ........................................................................................................................................................... 1 Year Approximate Assembly & Setup Time .............................................................................................................. 1 Hour Serial Number Location ................................................................................................. ID Label on Front of Machine Sound Rating ..................................................................................................................................................... 90 dB ISO 9001 Factory .................................................................................................................................................. Yes Certified by a Nationally Recognized Testing Laboratory (NRTL) .......................................................................... No

Features:

2.5 Micron Upper Bag Filtration 14-1/2" Balanced Steel, Radial Fin Impeller Heavy-Duty Steel Stand with 3" Casters and Brakes Green Powder Coated Paint Sturdy Collection Bags with 24 cu. ft. Total Capacity Four-Port Intake Manifold for Even Distribution to Collection Bags

Model G0671

Model G0671/G0672/G0673 (Mfd. Since 6/17)

PAGE 2 OF 2

-5-

MACHINE DATA SHEET

4000 3750 3500 3250 3000 2750 2500 2250 2000 1750 1500 1250 1000 750 500 250 0

CFM

0 Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901

MODEL G0671 4 HP DUST COLLECTOR Performance Curve

1.0

2.0

3552

3.0

4.0

5.0

6.0

7.0

8.0

9.0

STATIC PRESSURE (Inch/H2O)

10.0 11.0 12.0 13.0 14.0

47 1 / 4 " 54" 47 1 / 4 " 54" 47 5 / 8 " 47 5 / 8 " Ø23 5 / 8 " 6 5 / 8 " Ø23 5 / 8 "

4 HP DUST COLLECTOR PERFORMANCE RESULTS Max CFM Max SP HP Volts Inlet

3551.6

13.5

4 HP 220V 10"

Impeller

14 1 / 2 "

Inlet Dia. (inch) CFM Static Pressure (Inch/H2O) Amps Air Speed (m/s)

10" 9" 8" 7" 6" 5" 4" 3" 3551.6 3454.8 3282.6 2916.6 2475.4 2098.7 1452.9 979.4

4.72

4.82

6.98

8.5

10.3

11.1

12.53

13.2

30 33 29.5

32.1

27.5

30.5

24 27.1

21 23 16.8

19.5

12.5

13.5

11 9.1

2" 484.3

13.5

31 3 / 8 " 8.6

4.5

31 3 / 8 " Ø10" Ø10" 73 7 / 8 " 73 7 / 8 " Test run using 30 micron upper and lower bag.

Ø23 5 / 8 " 6 5 / 8 " 107 7 / 8 " Ø23 5 / 8 " 107 7 / 8 "

Model G0671

-6-

Page 3 of 3

Model G0671/G0672/G0673 (Mfd. Since 6/17)

G0672 Machine Data Sheet

MACHINE DATA SHEET

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

MODEL G0672 5 HP INDUSTRIAL DUST COLLECTOR Product Dimensions:

Weight.............................................................................................................................................................. 286 lbs.

Width (side-to-side) x Depth (front-to-back) x Height......................................................................... 74 x 29 x 134 in.

Footprint (Length x Width)............................................................................................................................ 74 x 29 in.

Shipping Dimensions:

Type............................................................................................................................ Cardboard Box & Wood Frame Content........................................................................................................................................................... Machine Weight.............................................................................................................................................................. 326 lbs.

Length x Width x Height....................................................................................................................... 42 x 29 x 30 in.

Must Ship Upright................................................................................................................................................... Yes

Electrical:

Power Requirement........................................................................................................... 220V, Single-Phase, 60 Hz Prewired Voltage.................................................................................................................................................. 220V Full-Load Current Rating........................................................................................................................................ 34A Minimum Circuit Size.............................................................................................................................................. 50A Connection Type........................................................................................... Permanent (Hardwire to Shutoff Switch) Power Cord Included.............................................................................................................................................. Yes Plug Included........................................................................................................................................................... No Switch Type.................................................................................................... Magnetic Switch w/Overload Protection

Motors: Main

Horsepower................................................................................................................................................ 5 HP Phase............................................................................................................................................ Single-Phase Amps............................................................................................................................................................ 34A Speed................................................................................................................................................ 3450 RPM Type................................................................................................................. TEFC Capacitor-Start Induction Power Transfer ............................................................................................................................... Direct Drive Bearings..................................................................................................... Shielded & Permanently Lubricated

Main Specifications: Operation

Dust Collector Type....................................................................................................................... Single-Stage Approved Dust Types................................................................................................................................ Wood Filter Type.................................................................................................................................................... Bag Airflow Performance.......................................................................................................................... 3961 CFM Max Static Pressure (at 0 CFM)............................................................................................................. 14.6 in.

Main Inlet Size........................................................................................................................................... 10 in.

Inlet Adapter Included.................................................................................................................................. Yes Number of Adapter Inlets.................................................................................................................................. 4 Adapter Inlet Size........................................................................................................................................ 4 in.

Machine Collection Capacity At One Time....................................................................................................... 4 Maximum Material Collection Capacity................................................................................................. 24 cu. ft.

Filtration Rating.................................................................................................................................. 2.5 Micron

Model G0672

Model G0671/G0672/G0673 (Mfd. Since 6/17)

PAGE 1 OF 2

-7-

Bag Information

Number of Upper Bags..................................................................................................................................... 2 Number of Lower Bags..................................................................................................................................... 2 Upper Bag Diameter............................................................................................................................ 23-5/8 in.

Upper Bag Length...................................................................................................................................... 70 in.

Lower Bag Diameter............................................................................................................................ 23-5/8 in.

Lower Bag Length...................................................................................................................................... 54 in.

Impeller Information

Impeller Type...................................................................................................................................... Radial Fin Impeller Size.............................................................................................................................................. 15 in.

Impeller Blade Thickness.......................................................................................................................... 1/4 in.

Construction

Upper Bag................................................................................................................................................ Fabric Lower Bag................................................................................................................................................ Plastic Frame.................................................................................................................... Steel Sheet Metal w/Casters Caster..................................................................................................................................................... Rubber Impeller....................................................................................................................................................... Steel Paint Type/Finish....................................................................................................................... Powder Coated Blower Housing............................................................................................................................. Formed Steel

Other Specifications:

Country of Origin .............................................................................................................................................. Taiwan Warranty ........................................................................................................................................................... 1 Year Approximate Assembly & Setup Time .............................................................................................................. 1 Hour Serial Number Location ................................................................................................. ID Label on Front fo Machine Sound Rating ..................................................................................................................................................... 92 dB ISO 9001 Factory .................................................................................................................................................. Yes Certified by a Nationally Recognized Testing Laboratory (NRTL) .......................................................................... No

Features:

2.5 Micron Upper Bag Filtration 15" Balanced Steel, Radial Fin Impeller Heavy-Duty Steel Stand with 3" Casters and Brakes Green Powder Coated Paint Sturdy Collection Bags with 24 cu. ft. Total Capacity Four-Port Intake Manifold for Even Distribution to Collection Bags

Model G0672

-8-

PAGE 2 OF 2

Model G0671/G0672/G0673 (Mfd. Since 6/17)

MACHINE DATA SHEET

Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901

MODEL G0672 5 HP DUST COLLECTOR Performance Curve

4500 4250 4000 3750 3500 3250 3000 2750 2500 2250 2000 1750 1500 1250 1000 750 500 250 0

CFM

0

3961

70" 54" 70" 57" 1.0

2.0

3.0

4.0

5.0

6.0

7.0

8.0

9.0

10.0 11.0 12.0 13.0 14.0 15.0

STATIC PRESSURE (Inch/H 2 O)

47 5 / 8 "

5 HP DUST COLLECTOR PERFORMANCE RESULTS Max CFM Max SP HP Volts Inlet

3960.6

14.6

5HP 220V 10"

Impeller

15"

Inlet Dia. (inch) CFM Static Pressure (Inch/H2O) Amps Air Speed (m/s)

10" 9" 8" 7" 6" 5" 4" 3" 3960.6 3809.9 3336.4 2744.4 2206.3 1560.6 1140.8 861.0

5.36

5.6

7.2

9.64

11.4

13.04

13.84

14.08

33.2

36.8

32.5

35.4

30 31 25.5

25.5

21.7

20.5

17.4

14.5

13.5

10.6

10.7

8 2" 9.5

6.1

31 3 / 8 " 656.5

14.6

31 3 / 8 " Ø10" 47 73 7 / 8 " Ø10" 5 / 8 " 73 7 / 8 " Test run using 2.5 micron upper bag and plastic lower collection bag. Max amp draw after adding 10" x 4" x 4 inlet: 30.3A.

Ø23 5 / 8 " 6 5 / 8 " Ø23 5 / 8 " Ø23 5 / 8 " 6 5 / 8 " Ø23 5 / 8 " 130 5 / 8 " 134"

Model G0672

Model G0671/G0672/G0673 (Mfd. Since 6/17)

Page 3 of 3

-9-

MACHINE DATA SHEET

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

MODEL G0673 10 HP INDUSTRIAL DUST COLLECTOR Product Dimensions:

Weight.............................................................................................................................................................. 410 lbs.

Width (side-to-side) x Depth (front-to-back) x Height......................................................................... 61 x 61 x 134 in.

Footprint (Length x Width)............................................................................................................................ 61 x 61 in.

Shipping Dimensions:

Type............................................................................................................................ Cardboard Box & Wood Frame Content........................................................................................................................................................... Machine Weight.............................................................................................................................................................. 472 lbs.

Length x Width x Height....................................................................................................................... 53 x 46 x 31 in.

Must Ship Upright................................................................................................................................................... Yes

Electrical:

Power Requirement..................................................................................................... 220V or 440V, 3-Phase, 60 Hz Prewired Voltage.................................................................................................................................................. 220V Full-Load Current Rating..................................................................................................... 30A at 220V, 15A at 440V Minimum Circuit Size.......................................................................................................... 40A at 220V, 20A at 440V Connection Type........................................................................................... Permanent (Hardwire to Shutoff Switch) Switch Type.................................................................................................... Magnetic Switch w/Overload Protection Voltage Conversion Kit.................................................................................................................. P0508037 for 440V Recommended Phase Converter....................................................................................................................... G7979

Motors: Main

Horsepower.............................................................................................................................................. 10 HP Phase.................................................................................................................................................... 3-Phase Amps..................................................................................................................................................... 30A/15A Speed................................................................................................................................................ 3450 RPM Type........................................................................................................................................... TEFC Induction Power Transfer ............................................................................................................................... Direct Drive Bearings..................................................................................................... Shielded & Permanently Lubricated

Main Specifications: Operation

Dust Collector Type....................................................................................................................... Single-Stage Approved Dust Types................................................................................................................................ Wood Filter Type.................................................................................................................................................... Bag Airflow Performance.......................................................................................................................... 5360 CFM Max Static Pressure (at 0 CFM)............................................................................................................. 17.9 in.

Main Inlet Size........................................................................................................................................... 10 in.

Inlet Adapter Included.................................................................................................................................. Yes Number of Adapter Inlets.................................................................................................................................. 5 Adapter Inlet Size........................................................................................................................................ 4 in.

Machine Collection Capacity At One Time....................................................................................................... 4 Maximum Material Collection Capacity................................................................................................. 48 cu. ft.

Filtration Rating.................................................................................................................................. 2.5 Micron

Model G0673

-10-

PAGE 1 OF 2

Model G0671/G0672/G0673 (Mfd. Since 6/17)

Bag Information

Number of Upper Bags..................................................................................................................................... 4 Number of Lower Bags..................................................................................................................................... 4 Upper Bag Diameter............................................................................................................................ 23-5/8 in.

Upper Bag Length...................................................................................................................................... 70 in.

Lower Bag Diameter............................................................................................................................ 23-5/8 in.

Lower Bag Length...................................................................................................................................... 54 in.

Impeller Information

Impeller Type...................................................................................................................................... Radial Fin Impeller Size.............................................................................................................................................. 17 in.

Impeller Blade Thickness.......................................................................................................................... 1/4 in.

Construction

Upper Bag................................................................................................................................................ Fabric Lower Bag................................................................................................................................................ Plastic Frame.................................................................................................................... Steel Sheet Metal w/Casters Caster..................................................................................................................................................... Rubber Impeller....................................................................................................................................................... Steel Paint Type/Finish....................................................................................................................... Powder Coated Blower Housing............................................................................................................................. Formed Steel

Other Specifications:

Country of Origin .............................................................................................................................................. Taiwan Warranty ........................................................................................................................................................... 1 Year Approximate Assembly & Setup Time ...................................................................................................... 1-1/2 Hours Serial Number Location ................................................................................................. ID Label on Front fo Machine ISO 9001 Factory .................................................................................................................................................. Yes Certified by a Nationally Recognized Testing Laboratory (NRTL) .......................................................................... No

Features:

2.5 Micron Upper Bag Filtration 17" Balanced Steel, Radial Fin Impeller Heavy-Duty Steel Stand with 3" Casters and Brakes Green Powder Coated Paint Sturdy Collection Bags with 48 cu. ft. Total Capacity Five-Port Intake Manifold for Even Distribution to Collection Bags

Model G0673

Model G0671/G0672/G0673 (Mfd. Since 6/17)

PAGE 2 OF 2

-11-

MACHINE DATA SHEET

Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901

MODEL G0673 10 HP DUST COLLECTOR Performance Curve

5500 5250 5000 4750 4500 4250 4000 3750 3500 3250 3000 2750 2500 2250 2000 1750 1500 1250 1000 750 500 250 0 0

CFM 5359.7

1.0

2.0

3.0

4.0

5.0

6.0

7.0

8.0

9.0

10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 19.0

STATIC PRESSURE (Inch/H 2 O)

70" 54" 55 1 / 2 " Ø23 5 / 8 " 8 1 / 2 " Ø23 5 / 8 " Ø10"

10 HP DUST COLLECTOR PERFORMANCE RESULTS Max CFM Max SP HP Volts Inlet

5359.7

17.9

10HP 220V 10"

Impeller

17" 80 3 / 8 " 132 1 / 2 " 60 5 / 8 "

Inlet Dia. (inch) CFM Static Pressure (Inch/H2O) Amps Air Speed (m/s)

10" 9" 8" 7" 6" 5" 4" 5359.7 5176.8 4229.7 3390.2 2604.5 1678.9 968.6

10.08

10.64

12.96

14.72

16.08

17.68

17.72

32.6

49.8

32.1

48.1

30 39.3

26.6

31.5

23.1

24.2

18.7

15.6

15.4

9 3" 430.5

17.8

13.1

4 2" 344.4

17.9

12 3.2

80 3 / 8 " Test run using 2.5 micron upper bag and plastic lower collection bag. Max amp draw after adding 10" x 4" x 5 inlet: 30.5A.

Model G0673

-12-

Page 3 of 3

Model G0671/G0672/G0673 (Mfd. Since 6/17)

SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating This Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor tance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Always use common sense and good judgment.

Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.

NOTICE

Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. It may also be used to alert against unsafe practices.

This symbol is used to alert the user to useful information about proper operation of the machine.

Safety Instructions for Machinery

OWNER’S MANUAL. Read and understand this owner’s manual BEFORE using machine. TRAINED OPERATORS ONLY. Untrained oper ators have a higher risk of being hurt or killed. Only allow trained/supervised people to use this machine. When machine is not being used, dis connect power, remove switch keys, or lock-out machine to prevent unauthorized use—especially around children. Make your workshop kid proof!

ELECTRICAL EQUIPMENT INJURY RISKS. You can be shocked, burned, or killed by touching live electrical components or improperly grounded machinery. To reduce this risk, only allow qualified service personnel to do electrical installation or repair work, and always disconnect power before accessing or exposing electrical equipment.

DANGEROUS ENVIRONMENTS. Do not use machinery in areas that are wet, cluttered, or have poor lighting. Operating machinery in these areas greatly increases the risk of accidents and injury.

MENTAL ALERTNESS REQUIRED. Full mental alertness is required for safe operation of machin ery. Never operate under the influence of drugs or alcohol, when tired, or when distracted.

DISCONNECT POWER FIRST. Always discon nect machine from power supply BEFORE making adjustments, changing tooling, or servicing machine. This prevents an injury risk from unintended startup or contact with live electrical components.

EYE PROTECTION. Always wear ANSI-approved safety glasses or a face shield when operating or observing machinery to reduce the risk of eye injury or blindness from flying particles. Everyday eyeglasses are NOT approved safety glasses.

Model G0671/G0672/G0673 (Mfd. Since 6/17) -13-

WEARING PROPER APPAREL. Do not wear clothing, apparel or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to reduce risk of slipping and losing control or accidentally contacting cutting tool or moving parts.

HAZARDOUS DUST. Dust created by machinery operations may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with each workpiece mate rial. Always wear a NIOSH-approved respirator to reduce your risk.

FORCING MACHINERY. Do not force machine. It will do the job safer and better at the rate for which it was designed.

NEVER STAND ON MACHINE. Serious injury may occur if machine is tipped or if the cutting tool is unintentionally contacted. STABLE MACHINE. Unexpected movement dur ing operation greatly increases risk of injury or loss of control. Before starting, verify machine is stable and mobile base (if used) is locked.

HEARING PROTECTION. Always wear hear ing protection when operating or observing loud machinery. Extended exposure to this noise without hearing protection can cause permanent hearing loss.

REMOVE ADJUSTING TOOLS. Tools left on machinery can become dangerous projectiles upon startup. Never leave chuck keys, wrenches, or any other tools on machine. Always verify removal before starting!

USE RECOMMENDED ACCESSORIES. Consult this owner’s manual or the manufacturer for rec ommended accessories. Using improper acces sories will increase the risk of serious injury.

UNATTENDED OPERATION. To reduce the risk of accidental injury, turn machine while unattended. OFF and ensure all moving parts completely stop before walking away. Never leave machine running USE CORRECT TOOL FOR THE JOB. Only use this tool for its intended purpose—do not force it or an attachment to do a job for which it was not designed. Never make unapproved modifica tions—modifying tool or using it differently than intended may result in malfunction or mechanical failure that can lead to personal injury or death!

AWKWARD POSITIONS. Keep proper footing and balance at all times when operating machine. Do not overreach! Avoid awkward hand positions that make workpiece control difficult or increase the risk of accidental injury.

MAINTAIN WITH CARE. Follow all maintenance instructions and lubrication schedules to keep machine in good working condition. A machine that is improperly maintained could malfunction, leading to serious personal injury or death. DAMAGED PARTS. Regularly inspect machine for damaged, loose, or mis-adjusted parts—or any condition that could affect safe operation. Immediately repair/replace BEFORE operating machine. For your own safety, DO NOT operate machine with damaged parts!

CHILDREN & BYSTANDERS. Keep children and bystanders at a safe distance from the work area.

Stop using machine if they become a distraction.

GUARDS & COVERS. Guards and covers reduce accidental contact with moving parts or flying debris. Make sure they are properly installed, undamaged, and working correctly BEFORE operating machine.

MAINTAIN POWER CORDS. When disconnect ing cord-connected machines from power, grab and pull the plug—NOT the cord. Pulling the cord may damage the wires inside. Do not handle cord/plug with wet hands. Avoid cord damage by keeping it away from heated surfaces, high traffic areas, harsh chemicals, and wet/damp locations.

EXPERIENCING DIFFICULTIES. If at any time you experience difficulties performing the intend ed operation, stop using the machine! Contact our Technical Support at (570) 546-9663.

-14 Model G0671/G0672/G0673 (Mfd. Since 6/17)

Additional Safety for Dust Collectors

Long-term respiratory damage can occur from using dust collectors without proper use of a respirator. Fire or explosions can result in smoke inhalation, serious burns, or death—if machine is used to collect incorrect materials, is operated near potential explosion sources, or ducting is improperly grounded. Entanglement, amputation, or death can occur if hair, clothing, or fingers are pulled into the inlet. To reduce the risk of these hazards, operator and bystanders MUST completely heed the hazards and warnings below.

INTENDED USE. Collecting the wrong materi als can result in serious inhalation hazards, fire, explosions, or machine damage. This machine is ONLY designed to collect wood dust and chips from woodworking machines. DO NOT use it to collect silica, polyurethane, toxic fumes, metal dust or shavings, lead paint, drywall, asbestos, biohaz ards, explosive dusts, flammable or combustible liquids or fumes, nor burning or smoking material. WEAR A RESPIRATOR. Fine dust that is too small to be caught in filter will be blown into ambi ent air. Always wear a NIOSH-approved respira tor during operation and for a short time after to reduce your risk of permanent respiratory damage. Never collect dust from any hazardous material.

POWER DISCONNECT. Turn machine OFF, dis connect from power supply, and allow impeller to completely stop before leaving machine unat tended, or doing any maintenance or service.

REGULAR CLEANING. To reduce risk of start ing a fire, regularly check/empty collection bags or drum to avoid buildup of fine dust, which can increase risk of fire. Regularly clean surrounding area where machine is operated—excessive dust buildup on overhead lights, heaters, electrical pan els, or other heat sources will increase risk of fire.

SUSPENDED DUST PARTICLES. To reduce risk of death or injury caused by explosions or fires, DO NOT operate in areas where these risks are high, including spaces near pilot lights, open flames, or other ignition sources.

IMPELLER HAZARDS. To reduce risk of entan glement or contact with impeller, DO NOT place hands, hair, clothing, or tools in or near open dust collection inlet during operation, and keep small animals and children away. The powerful suction could easily pull them into impeller. HAZARDOUS DUST. Dust exposure created while using machinery may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with each workpiece material, and always wear a NIOSH-approved respirator.

AVOIDING SPARKS. To reduce risk of fire, avoid collecting any metal objects or stones. These can possibly produce sparks when they strike impeller, which can smolder in wood dust for a long time before a fire is detected. If you accidentally cut into wood containing metal, immediately turn dust collector, disconnect from power, and wait for impeller to stop. Then empty bag or drum into approved airtight metal container.

OFF EMPTYING DUST. When emptying bag or drum, wear respirator and safety glasses. Empty dust away from ignition sources and into approved container.

FIRE SUPPRESSION. Only operate dust collector in locations that contain fire suppression system or have fire extinguisher nearby.

STATIC ELECTRICITY. To reduce risk of fire or explosions caused by sparks from static electricity, ground all ducting using grounding wire. OPERATING LOCATION. To reduce respiratory exposure to fine dust, locate permanently installed dust collectors away from working area or in anoth er room. DO NOT place dust collector where it can be exposed to rain or moisture, which creates a shock hazard and will reduce life of machine.

DUST ALLERGIES. Dust from certain woods will cause an allergic reaction. Make sure you know what type of wood dust you will be exposed to in case of an allergic reaction.

Model G0671/G0672/G0673 (Mfd. Since 6/17) -15-

SECTION 2: POWER SUPPLY

Availability

Before installing the machine, consider the avail ability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize the risk of electrocution, fire, or equipment damage, installation work and electrical wiring must be done by an electrician or qualified service personnel in accordance with all applicable codes and standards.

Electrocution, fire, shock, or equipment damage may occur if machine is not properly grounded and connected to power supply.

Full-Load Current Rating

The full-load current rating is the amperage a machine draws at 100% of the rated output power. On machines with multiple motors, this is the amperage drawn by the largest motor or sum of all motors and electrical devices that might operate at one time during normal operations.

G0671 Full-Load Current Rating at 220V ..... 26 Amps G0672 Full-Load Current Rating at 220V ..... 34 Amps G0673 Full-Load Current Rating at 220V ..... 30 Amps Full-Load Current Rating at 440V ..... 15 Amps

The full-load current is not the maximum amount of amps that the machine will draw. If the machine is overloaded, it will draw additional amps beyond the full-load rating.

If the machine is overloaded for a sufficient length of time, damage, overheating, or fire may result— especially if connected to an undersized circuit. To reduce the risk of these hazards, avoid over loading the machine during operation and make sure it is connected to a power supply circuit that meets the specified circuit requirements.

Circuit Information

A power supply circuit includes all electrical equipment between the breaker box or fuse panel in the building and the machine. The power sup ply circuit used for this machine must be sized to safely handle the full-load current drawn from the machine for an extended period of time. (If this machine is connected to a circuit protected by fuses, use a time delay fuse marked D.)

For your own safety and protection of property, consult an electrician if you are unsure about wiring practices or electrical codes in your area.

Note: Circuit requirements in this manual apply to

a dedicated circuit—where only one machine will be running on the circuit at a time. If machine will be connected to a shared circuit where multiple machines may be running at the same time, con sult an electrician or qualified service personnel to ensure circuit is properly sized for safe operation.

-16 Model G0671/G0672/G0673 (Mfd. Since 6/17)

G0671 Circuit Requirements for 220V

This machine is prewired to operate on a power supply circuit that has a verified ground and meets the following requirements:

Nominal Voltage ......... 208V, 220V, 230V, 240V Cycle ..........................................................60 Hz Phase ........................................... Single-Phase Power Supply Circuit ......................... 40 Amps

G0672 Circuit Requirements for 220V

This machine is prewired to operate on a power supply circuit that has a verified ground and meets the following requirements:

Nominal Voltage ......... 208V, 220V, 230V, 240V Cycle ..........................................................60 Hz Phase ........................................... Single-Phase Power Supply Circuit ......................... 50 Amps

G0672 Circuit Requirements for 220V

This machine is prewired to operate on a power supply circuit that has a verified ground and meets the following requirements:

Nominal Voltage ......... 208V, 220V, 230V, 240V Cycle ..........................................................60 Hz Phase .................................................... 3-Phase Power Supply Circuit ......................... 40 Amps

G0673 Circuit Requirements for 440V

This machine can be converted to operate on a power supply circuit that has a verified ground and meets the requirements listed below. (Refer to Voltage Conversion instructions for details.)

Nominal Voltage ......... 208V, 220V, 230V, 240V Cycle ..........................................................60 Hz Phase .................................................... 3-Phase Power Supply Circuit ......................... 20 Amps

Connection Type

A permanently connected (hardwired) power sup ply is typically installed with wires running through mounted and secured conduit. A disconnecting means, such as a locking switch (see following figure), must be provided to allow the machine to be disconnected (isolated) from the power supply when required. This installation must be performed by an electrician in accordance with all applicable electrical codes and ordinances.

Power Source Locking Disconnect Switch Machine Conduit Conduit Ground Ground Figure 1. Typical setup of a permanently connected machine.

Grounding Instructions

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electric shock. A permanently connected machine must be connected to a grounded metal permanent wir ing system; or to a system having an equipment grounding conductor. All grounds must be verified and rated for the electrical requirements of the machine. Improper grounding can increase the risk of electric shock!

Serious injury could occur if you connect machine to power before completing setup process. DO NOT connect to power until instructed later in this manual.

Extension Cords

Since this machine must be permanently con nected to the power supply, an extension cord cannot be used.

Model G0671/G0672/G0673 (Mfd. Since 6/17) -17-

G0673 440V Conversion

The Model G0673 can be converted for 440V operation. This conversion job consists of dis connecting the machine from the power source, changing the connections on the magnetic switch and rewiring the motor for 440V operation. The Model G0673 440V Conversion Kit (Part #P0673036) for this procedure can be purchased by calling Grizzly Customer Service at (800) 523 4777.

All wiring changes must be performed by an elec trician or qualified service personnel before the machine is connected to the power source. If, at any time during this procedure you need help, call Grizzly Tech Support at (570) 546-9663.

To rewire the Model G0673 for 440V operation:

1. DISCONNECT MACHINE FROM POWER!

2. Remove the magnetic switch cover, then disconnect and remove the 220V magnetic switch ( see Figure 2).

3. Install the 440V magnetic switch and wire it according to the G0673 Wiring Diagram on

Page 45.

4. Remove the motor junction box cover, rewire the motor as shown on the diagram located inside the junction box, then re-install the cover.

Note: The reference motor wiring diagram on Page 45 was current at the time of printing,

but always use the wiring diagram provided inside the motor junction box, as it will reflect any changes to the motor shipped with your machine.

-18 Figure 2. 220V magnetic switch.

Model G0671/G0672/G0673 (Mfd. Since 6/17)

SECTION 3: SETUP

This machine presents serious injury hazards to untrained users. Read through this entire manu al to become familiar with the controls and opera tions before starting the machine!

Wear safety glasses during the entire setup process!

HEAVY LIFT!

Straining or crushing injury may occur from improperly lifting machine or some of its parts. To reduce this risk, get help from other people and use a forklift (or other lifting equipment) rated for weight of this machine.

Needed for Setup

The following are needed to complete the setup process: • • • • •

Description Qty

• Assistant ........................................1 or more • Safety Glasses (for each person) ............... 1 Gloves (for each person) ............................ 1 Phillips Head Screwdriver........................... 1 Wrench 10mm ............................................ 1 Wrenches 12mm ........................................ 2 Ladder (for hanging upper bag) .................. 1

Unpacking

This machine was carefully packaged for safe transport. When unpacking, separate all enclosed items from packaging materials and inspect them for shipping damage.

If items are damaged, please call us immediately at (570) 546-9663.

IMPORTANT: Save all packaging materials until you are completely satisfied with the machine and have resolved any issues between Grizzly or the shipping agent. You MUST have the original pack-

aging to file a freight claim. It is also extremely helpful if you need to return your machine later.

SUFFOCATION HAZARD!

Keep children and pets away from plastic bags or packing materials shipped with this machine. Discard immediately.

-19 Model G0671/G0672/G0673 (Mfd. Since 6/17)

G0671/G0672 Inventory

The following is a list of items shipped with your machine. Before beginning setup, lay these items out and inventory them.

If any non-proprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store.

NOTICE

If you cannot find an item on this list, care fully check around/inside the machine and packaging materials. Often, these items get lost in packaging materials while unpack ing or they are pre-installed at the factory.

• • • • • • •

Contents (Figures 3 & 4) Qty

A. Collectors ................................................... 2 B. Impeller Housing with Motor ....................... 1 C. Casters ....................................................... 4 D. Leg Braces ................................................. 4 E. Combo Wrench 10 x 12mm ........................ 1 F. Legs ............................................................ 4 G. Gaskets ...................................................... 2 H. 4-in-1 Inlet Adapter ..................................... 1 I. Hangers ...................................................... 2 J. Hanger Supports ........................................ 2 K. Lower Collection Bags (Plastic) .................. 2 L. Upper Filter Bags (Fabric) .......................... 2

Fasteners (where used) (not shown)

• Hex Bolts 5 ⁄ 16 "-18 x 2 1 ⁄ 2

Qty

" (legs) .................... 8 Hex Nuts Hex Bolts Hex Bolts Hex Bolts 5 5 5 1 ⁄ ⁄ ⁄ ⁄ 16 16 16 4 "-18 (legs/collectors) ............. 24 "-18 x "-20 x 1 ⁄ 1 2 ⁄ 2 " (leg braces) .......... 16 "-18 x 1" (collectors) ............. 16 " (hangers) ................. 6 Flat Washers 5 ⁄ 16 " (collectors) .................. 32 Phillips Head Screw 10-24 X 3 ⁄ 8 " (inlet) ...... 1 Bag Clamps (bags) ..................................... 4 A B F C D E

Figure 3.

G0671/G0672 Inventory 1.

I J H K G L Figure 4. G0671/G0672 Inventory 2.

-20 Model G0671/G0672/G0673 (Mfd. Since 6/17)

G0673 Inventory

The following is a list of items shipped with your machine. Before beginning setup, lay these items out and inventory them.

If any non-proprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store.

NOTICE

If you cannot find an item on this list, care fully check around/inside the machine and packaging materials. Often, these items get lost in packaging materials while unpack ing or they are pre-installed at the factory.

Contents (Figures 5–7) Qty

A. Collectors ................................................... 4 B. 5-in-1 Inlet Adapter ..................................... 1 C. G0673 Impeller Housing with Motor ........... 1 D. Legs ............................................................ 4 E. Leg Braces ................................................. 4 F. Combo Wrench 10 x 12mm ........................ 1 G. Casters ....................................................... 4 H. Upper Filter Bags (Fabric) .......................... 4 I. Lower Collection Bags (Plastic) .................. 4 J. Hangers ...................................................... 4 K. Hanger Supports ........................................ 4 L. Rubber Gaskets ......................................... 4 M. Bag Clamps ................................................ 8 • • • • •

Fasteners (where used) (not shown)

• • Hex Bolts 5 ⁄ 16 "-18 x 2 1 ⁄ 2

Qty

" (legs) .................... 8 Hex Nuts 5 ⁄ 16 "-18" (legs/collectors) ............ 40 Hex Bolts Hex Bolts Hex Bolts 5 5 1 ⁄ ⁄ ⁄ 16 16 4 "-18 x "-20 x Flat Washers 5 ⁄ 16 1 ⁄ 1 2 ⁄ 2 " (leg braces) .......... 16 "-18 x 1" (collectors) ............. 32 " (hangers) ............... 12 " (collectors) ................... 64 Phillips Head Screw 10-24 X 3 ⁄ 8 " (inlet) ...... 1 B C A D F Figure 5. G0673 Inventory 1.

E H G I J K Figure 6. G0673 Inventory 2.

L M Figure 7. G0673 Inventory 3.

Model G0671/G0672/G0673 (Mfd. Since 6/17) -21-

Site Considerations

Weight Load

Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be installed on the machine, and the heaviest work piece that will be used. Additionally, consider the weight of the operator and any dynamic loading that may occur when operating the machine.

Space Allocation

Consider the largest size of workpiece that will be processed through this machine and provide enough space around the machine for adequate operator material handling or the installation of auxiliary equipment. With permanent installations, leave enough space around the machine to open or remove doors/covers as required by the main tenance and service described in this manual.

See below for required space allocation.

Children or untrained people may be seriously injured by this machine. Only install in an access restricted location.

Physical Environment

The physical environment where the machine is operated is important for safe operation and lon gevity of machine components. For best results, operate this machine in a dry environment that is free from excessive moisture, hazardous chemi cals, airborne abrasives, or extreme conditions. Extreme conditions for this type of machinery are generally those where the ambient temperature range exceeds 41°–104°F; the relative humidity range exceeds 20%–95% (non-condensing); or the environment is subject to vibration, shocks, or bumps.

Electrical Installation

Place this machine near an existing power source. Make sure all power cords are protected from traffic, material handling, moisture, chemicals, or other hazards. Make sure to leave enough space around machine to disconnect power supply or apply a lockout/tagout device, if required.

Lighting

Lighting around the machine must be adequate enough that operations can be performed safely. Shadows, glare, or strobe effects that may distract or impede the operator must be eliminated.

73 7 ⁄ 8 " 31 3 ⁄ 8 " G0671/G0672 80 3 ⁄ 8 " 80 3 ⁄ 8 " G0673 Figure 1. Model G0671-3 illustrated top view and suggested clearances.

-22 Model G0671/G0672/G0673 (Mfd. Since 6/17)

Assembly

To assemble the dust collector:

1. With assistance, place the impeller housing on the floor so that the motor is pointing up.

2. Insert the legs into the leg mounting brackets and secure them with the eight 5 ⁄ 16 "-18 x 2 1 ⁄ 2 " hex bolts and 5 ⁄ 16 "-18 hex nuts, as shown in Figure 8. Do not yet fully tighten the nuts.

4. Attach the four casters to the legs by thread ing them into the bottom of the legs, as shown in Figure 11.

Caster Leg Leg x8 Leg Mounting Bracket

Figure 8.

Attaching legs to impeller housing (Model G0673 shown).

3. Attach the four leg braces to the legs with the (16) 5 ⁄ ware from 16 "-18 x Step 2.

1 ⁄ 2 " hex bolts, as shown in Figure 9. Fully tighten the bolts and the hard Leg Leg Brace x4 Figure 10. Attaching casters.

5. With assistance, turn the entire assembly over so that the casters rest on the floor.

6. Use (8) shown in 5 ⁄ 16 "-18 x 1" hex bolts, (16) washers, and (8) 5 ⁄ Figure 10.

16 5 ⁄ 16 " flat "-18 hex nuts to attach each collector to the impeller housing with a rubber gasket between the components, as Collector 5 ⁄ 16 " Flat Washers Impeller housing 5 ⁄ 16 "-18 Hex Nut 5 ⁄ 16 "-18 x 1" Hex Bolt Rubber Gasket Figure 11. Collector mounted to impeller housing.

x16 Figure 9. Attaching leg braces.

Model G0671/G0672/G0673 (Mfd. Since 6/17) -23-

Note: The Model G0673 is a three-phase

machine. If it is wired out of phase, the machine may not function properly. Proceed to Test Run on Page 26 to determine if your machine is wired in phase, then proceed to

Step 7.

The Models G0671 and G0672 are single phase and cannot be wired out of phase. For these models, continue below.

7. Attach the inlet to the top of the impeller housing with the #10-24 x 3/8" Phillips head screw, as shown in Figure 12.

9. Mount the hanger assembly on the protruding rod on the collector with one (Model G0671/ G0672) or two (Model G0673) 1 ⁄ 4 "-20 x 1 ⁄ 2 " hex bolts, as shown in Figure 14.

Hanger Assembly Hex Bolt 1 ⁄ 4 "-20 x 1 ⁄ 2 " Phillips Head Screw Figure 12. Inlet mounted on impeller housing.

8. Secure the hanger into the hanger sup port with one (Model G0673) or two (Model G0671/G0672) 1 ⁄ 4 "-20 x 1 ⁄ 2 " hex bolts (see Figure 13).

Hanger 1 Hex Bolts ⁄ 4 "-20 x 1 ⁄ 2 " Figure 14. Hanger assembly mounted onto collector (G0671/G0672).

10. Align the hanger assembly so that the hook is directly over the center of the collector.

11. Repeat Steps 8–10 for the remaining hanger assemblies.

12. Place the loop at the top of each upper col lection bag over each hook on the hanger assemblies (see Figure 15).

Hook Bag Loop Hanger Assembly Figure 15. Upper filter bag mounted on hanger assembly.

Hanger Support Figure 13. Hanger attached to hanger support (G0671/G0672 shown).

-24 Model G0671/G0672/G0673 (Mfd. Since 6/17)

13. Thread the bag clamp into and around the bottom seam of the upper collection bag (see Figure 16).

Bag Clamp Collector Hook Figure 16. Upper filter bag secured to collector.

14. Slip the bottom of the bag with the clamp over the top lip of the collector.

15. Fasten the locking mechanism of the bag clamp to secure the bag to the collector (see Figure 16). 16. Repeat Steps 12–15 for the remaining upper bags.

17. Install the lower bags.

Model G0671: Repeat Steps 12-15 in a similar manner to install the remaining lower collection bags on the lower rims of each collector. Then, proceed to Test Run on Page 26.

Model G0672-73: Slip the lower plastic collection bag over the bottom lip of the col lector and position the bag evenly around the collector.

Snag the bag on the hooks to hold it in place until the bag clamp can be secured (see Figure 17).

Figure 17. Bottom collection bag snagged on collector hooks.

18. Wrap the bag clamp around the collector, position it between the bottom lip of the col lector and the hooks, and fasten the bag clamp to secure the bag to the collector (see Figure 18).

Bag Clamp Figure 18. Lower collection bag secured to collector.

19. Repeat Steps 16 & 17 for the remaining Model G0672-73 lower bag assemblies.

Model G0671/G0672/G0673 (Mfd. Since 6/17) -25-

Test Run

Once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular operation. The test run consists of verifying the following: 1) The motor powers up and runs correctly, and 2) (Model G0673 only), the motor turns the correct direction (machine is not wired out of phase).

If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review the Troubleshooting on Page 40. If you still cannot remedy a problem, contact our Tech Support at (570) 546-9663 for assistance.

Before starting the dust collector, make sure you have performed the preceding assembly instructions, and you have read through the rest of the manual and are familiar with the various functions and safety features on this machine. Failure to follow this warning could result in serious personal injury or even death!

To test run the machine:

1. Make sure you have read the safety instruc tions at the beginning of the manual and that the machine is setup properly.

2. Make sure all tools and objects used during setup are cleared away from the machine.

3. Connect the machine to the power source.

4. Turn the machine ON by pushing in the GREEN button on the power switch.

5. Listen to and watch for abnormal noises or actions. The machine should run smoothly with little or no vibration or rubbing noises.

— Strange or unusual noises should be inves tigated and corrected before operating the machine further. Always disconnect the machine from power when investigating or correcting potential problems.

6. Turn the machine OFF by pushing in the RED button on the power switch.

7. Model G0673 Only: Verify that the power is not connected out of phase by starting/ stopping the machine and determining if the motor turns in the correct direction, using the criteria below: — If the impeller turns counterclockwise (when looking down on the inlet port on the impeller housing), it is turning in the correct direction.

— If the impeller turns clockwise, it is turning in the wrong direction. Stop the machine, shut off the power source, then swap any two of the three power wires that connect to the machine.

-26 Model G0671/G0672/G0673 (Mfd. Since 6/17)

SECTION 4: DESIGNING THE SYSTEM General

The Model G0671/G0672/G0673 can be operated as either a stationary or mobile unit. There are advantages and disadvantages to both set-ups. The advantage of the mobile system is eliminating the cost of many ducts and fittings. On the other hand, the stationary system is more versatile and convenient. The Model G0671/G0672/G0673 is designed to be a central dust collector system. Locate the dust collector in an out of the way location such as a corner or separate room. These machines can accommodate the following number of machines each drawing 400 CFM on a 4" dust port: G0671: ............................................................... 8 G0672: ............................................................... 9 G0673: ............................................................. 12 The large suction capacity of the Model G0671/ G0672/G0673 allows great flexibility in planning and designing of your dust collection duct layout. Grizzly offers a complete line of dust collection accessories for setting up a stationary system. Additionally, Grizzly offers a complete guide book titled Dust Collection Basics. A 4-port inlet is included with the Model G0671/ G0672 and a 5-port inlet is included with the Model G0673 for quick and economical dust col lection setup. However, depending upon your system design using this feature, bags may fill at different rates requiring you to empty some bags more often than others.

Whatever system you choose, always make sure there are no open flames (including pilot lights) in the same room as the dust collector; otherwise you risk an explosion if dust is dispersed into the air.

Duct Material

You have many choices regarding main line and branch line duct material. For best results, use metal duct for the main line and branch lines, then use short lengths of flexible hose to connect each machine to the branch lines.

Plastic duct is also a popular material for home shops. However, be aware that there is a fire or explosion hazard if plastic duct material is used for dust collection without being grounded against static electrical charge build-up. This topic will be discussed later in this section. Another problem with using plastic is that it is less efficient per foot than metal.

Metal Duct

Advantages of metal duct (see Figure 19) is its conductivity and that it does not contribute to static electrical charge build-up. However, static charges are still produced when dust particles strike other dust particles as they move through the duct. Since metal duct is a conductor, it can be grounded quite easily to dissipate any static electrical charges. Figure 19. Examples of metal pipe and components.

-27 Model G0671/G0672/G0673 (Mfd. Since 6/17)

There are quite a number of options when it comes to metal duct, but metal duct that is spe cially manufactured for dust collection is the best choice. When selecting your metal duct, choose high quality metal duct with smooth welded inter nal seams that will minimize airflow resistance. This type of duct usually connects to other ducts or elbows with a simple, self-sealing clamp, is very quick and easy to assemble, and can be readily dismantled and re-installed. This is espe cially important if you ever need to change things around in your shop or add more machines. See the Accessories section on Page 36 for exam ples.

Avoid inferior metal duct that requires you to cut it to length and snap it together. This type of duct is time consuming to install because it requires you to seal all the seams with silicone and screw the components on the ends with sheet metal screws. Another disadvantage is the rough internal seams and crimped ends that unavoidably increase static pressure loss.

Flexible Duct

Flexible hose is generally used for short runs, small shops and at rigid duct-to-tool connections. There are many different types of flex hose on the market today. These are manufactured from materials such as polyethylene, PVC, cloth hose dipped in rubber and even metal, including steel and aluminum.

The superior choice for flexible ducting is metal flex hose that is designed to be flexible and as smooth as possible to reduce static pressure loss.

There are also many kinds of pure plastic flexible hose, such as non-perforated drainage type hose and dryer vent hose. Drainage type hose, while being economical, does not quite have the flex ibility required for dust collection. The inside of the duct is also deeply corrugated and can increase the static pressure loss by as much as 50% over smooth wall duct. Dryer vent hose offers greater flexibility, but is non-resistant to abrasion and tends to collapse in a negative pressure system. We DO NOT recommend using dryer vent hose in your dust collection system.

If using flex-hose, choose one of the many types designed specifically for the movement of solid particles, i.e. dust, grains and plastics. However, the cost of specifically designed flexible duct can vary greatly. Grizzly offers polyethylene hose, which is well suited for the removal of particulate matter, especially sawdust, since it is durable and completely flexible. Polyethylene is also very eco nomical and available in a wide variety of diam eters and lengths for most applications.

Plastic Duct

The popularity of plastic duct is due to the fact that it is economical and readily available. It is also simple to assemble and easily sealed against air loss. The primary disadvantage of plastic duct for dust collection is the inherent danger of static electrical build-up. Figure 21. Example of plastic duct and components.

-28 Figure 20. Example of flexible metal duct.

Model G0671/G0672/G0673 (Mfd. Since 6/17)

System Design

Step 1. Decide Who Will Design

For most small-to-medium sized shops, you can design and build the dust collection system your self without hiring engineers or consultants. We have included some basic information here to get you started on a dust collection system design.

If you have a large shop or must design a com plicated system, then we recommend that you perform additional research beyond this manual, or seek help from an expert.

Step 2. Sketch Your Shop Layout

Planning is the most important step when design ing a successful dust collection system.

Before you begin to draw your necessary layout sketch, we recommend that you visit our FREE Workshop Planner available on our website at www.grizzly.com. Our Workshop Planner will allow you to quickly and easily draw and print a basic shop layout. Don't worry, non-Grizzly brand machines can be substituted with Grizzly machines for layout pur poses. Note: After you're finished, make sure to

save your layout for later modification.

Your sketch only needs the basic details of the shop layout, similar to Figure 22, including all your current/planned machines and your planned placement of the dust collector.

Step 3. Sketch a Basic Duct Layout

For the next step, sketch how your machines will connect to the dust collector. Consider these gen eral guidelines for planning an efficient system: 1. Machines that produce the most sawdust should be placed nearest to the dust collector (i.e. planers and sanders).

2. Ideally, you should design the duct system to have the shortest possible main line and secondary branch ducts. See layouts.

Figures 23 &

24 for ideas of good duct layouts vs bad duct Branch Line Ducts Main Line Duct

GOOD

Figure 23. Good duct layout.

BAD

Dust Collector Figure 24. Bad duct layout.

Figure 22. Initial sketch of shop layout.

Model G0671/G0672/G0673 (Mfd. Since 6/17) -29-

3. Directional changes should be kept to a mini mum. The more directional change fittings you use directly increases the overall resis tance to airflow.

4. Gradual directional changes are more effi cient than sudden directional changes (i.e. use the largest corner radius possible when changing hose or pipe direction).

5. Each branch line should have a blast gate immediately after the branch to control suc tion from one machine to another.

6. The simpler the system, the more efficient and less costly it will be.

Step 4. Determine Required CFM of Each Machine

Since each machine produces a different amount of sawdust, the requirements for the minimum amount of CFM needed to move that sawdust is unique to the machine (for example, a planer pro duces more sawdust than a table saw). Knowing this required CFM is important in gauging which size of duct to use.

Figure 25 will give you a close estimation of the airflow your machine requires. Machines that generate the most sawdust should be placed near the dust collector. If the machine has multiple dust ports, the total CFM required is the sum of all ports.

Machine Dust Port Size

2" 2.5" 3" 4" 5" 6" 7" 8" 9" 10"

Approximate Required CFM

98 150 220 395 614 884 1203 1570 1990 2456 Figure 25. Approximate required airflow for machines, based on dust port size.

-30 If your machine does not have a built in dust port, use Figure 26 to determine the size of dust port to install on your machine.

Machine Average Dust Port Size

Table Saw ......................................................4" Miter/Radial-Arm Saw ....................................2" Jointer (6" and smaller) .................................4" Jointer (8"-12") ...............................................5" Thickness Planer (13" and smaller) ...............4" Thickness Planer (14"-20") ............................6" Shaper ...........................................................4" Router (mounted to table) ..............................2" Bandsaw ........................................................4" Lathe ..............................................................4" Disc Sander (12" and smaller) .......................2" Disc Sander (13-18") ......................................4" Belt Sander (6" and smaller) .........................2" Belt Sander (7"-9") ........................................3" Edge Sander (6" x 80" and smaller) ..............4" Edge Sander (6" x 80" and larger) ................5" Drum Sander (24" and smaller) ...............2 x 4" Drum Sander (24" and larger) .................4 x 4" Widebelt Sander (18" and smaller) ................5" Widebelt Sander (24"–37" single head) ..2 x 6" Widebelt Sander (24"_51" double head) .5 x 4" Figure 26. Dust port size and quantity per average machine.

Write the required CFM for each machine on your sketch, as shown in Figure 27.

395 395 790 98 220 395 614 Figure 27. CFM requirements labeled for each machine.

Model G0671/G0672/G0673 (Mfd. Since 6/17)

Determining Main Line Duct Size

The general rule of thumb for a main line duct is that the velocity of the airflow must not fall below 3500 FPM.

Use the inlet size of the dust collector as a starting point for the main line. Neck the main line down 1" for every 10' of length. This will usually keep the air velocity above 3500 FPM and, depending on your system, will allow you to keep multiple branches open at one time.

For the Model G0671/G0672/G0673 this is 10". Mark your drawing, as in Figure 28.

395 395 790 98 9“ 10“ 220 395 614 Figure 28. Main line size labeled on sketch.

Determining Branch Line Duct Size

The general rule of thumb for a branch line duct is that the velocity of the airflow must not fall below 4000 FPM.

For small/medium sized shops, using the dust port size from the machine as the branch line duct size will achieve the correct velocity in most appli cations. However, if the dust port on the machine is smaller than 4", make the branch line 4" and reduce the line right before the dust port.

Note: Systems with powerful dust collectors work

better if multiple blast gates are left open. This also allows you to run two machines at once. Experiment with different combinations of blast gates open/closed to find the best results for your system.

Write your determined branch line sizes on your drawing, as shown in Figure 29.

Model G0671/G0672/G0673 (Mfd. Since 6/17) 98 4“ 395 4“ 9“ 395 4“ 10“ 6“ 790 4“ 4“ 5“ 220 395 614 Figure 29. Branch line sizes labeled on sketch.

Multiple Dust Ports

If your machine has multiple dust ports, add the total CFM given for each dust port size from Figure 25. Refer to Figure 30 and find the CFM that is closest to your total to determine the cor rect branch size. Split the branch line just before the dust ports with matching duct sizes.

Two Machines on Same Branch Line

If both machines will be running at the same time, add the total CFM given for each dust port size from Figure 25.

If both the machines will never be run at the same time, reference the machine with biggest dust port to Figure 30 and add blast gates after the Y-branch to open/close the line to each machine.

Total CFM

<500 600 700 800 1000

Branch Line Size

4" 5" 5" 6" 6" 1200 1400 1600 7" 8" 8" Figure 30. Branch line sizing chart by total CFM (for use when multiple machines share line).

-31-

Calculating Duct Resistance

Adding duct work, elbows, branches and any other components to a duct line increases airflow resistance (static pressure loss). This resistance can be minimized by using rigid (smooth) pipe and gradual curves, as opposed to flexible pipe and 90˚ elbows. To help you think about this resistance, imagine riding a bicycle in a tunnel that is an exact replica of your duct work. If the inside of the tunnel is very bumpy (flexible pipe) and has many sharp turns (90˚ elbows), it will take a lot more effort for you to travel from one end to the other than if your path is smooth and straight.

The purpose of calculating this resistance is to determine if it is low enough from the machine to the dust collector to meet the given requirement for the machine. Use the charts in Figure 32 to calculate the resistance of duct work.

Duct Dia.

2" 2.5" 3" 4" 5" 6" 7" 8" 9"

Approximate Static Pressure Loss Per Foot of Rigid Pipe

Main Lines at 3500 FPM Branch Lines at 4000 FPM 0.091

0.08

0.122

0.107

0.071

0.057

0.046

0.037

0.029

0.023

0.017

0.094

0.075

0.059

0.047

0.036

0.027

0.019

Approximate Static Pressure Loss Per Foot of Flex Pipe

Main Lines at 3500 FPM Branch Lines at 4000 FPM 0.35

0.306

0.453

0.397

0.271

0.215

0.172

0.136

0.106

0.08

0.057

0.352

0.28

0.225

0.18

0.141

0.108

0.079

Fitting Dia.

3" 4" 5" 6" 7" 8"

90˚ Elbow

0.47

0.45

0.531

0.564

0.468

0.405

45˚ Elbow

0.235

0.225

0.266

0.282

0.234

0.203

45˚ Wye(Y)

0.282

0.375

0.354

0.329

0.324

0.297

Figure 31. Static pressure loss charts.

90˚ Wye(Y)

0.188

0.225

0.236

0.235

0.216

0.189

-32 In most small/medium shops it is only necessary to calculate FPM for the line (from the dust collec tor to the machine) with the longest duct length or the most fittings (operating under the assumption that if the line with the highest resistance works, the others will be fine). The line with the longest duct length and most fit tings in our system sketch (see 220 CFM.

Figure 27) is the one connected to the router table, which draws

To calculate the static pressure loss of any given line in the system, follow these steps:

1. Make a list of each size duct in the line, including the length, and multiply those num bers by the static pressure loss value given in Figure 31.

2. List each type of elbow or branch and multiply the quantity (if more than one) by the static pressure loss given in Figure 31.

3. Add the additional factors from Figure 32 to your list.

Additional Factors

Seasoned (well used) Dust Collection Filter

Static Pressure Loss

1 Entry Loss at Large Machine Hood 2 Figure 32. Additional factors affecting static pressure loss.

Model G0671/G0672/G0673 (Mfd. Since 6/17)

4. Total your list, as shown in the example in Figure 33, to come up with your overall static pressure loss number for that line.

Note: Always account for a seasoned filter,

so you don't end up with a system that only works right when the filter is clean.

Main Line

6" Rigid Pipe (0.037) at 20' ................ 0.740

Branch Line

4" Rigid Pipe (0.075) at 10' ................ 0.750

4" Flex Pipe (0.28) at 5' ........................ 1.400

Elbows/Branches

6" 45˚ Y-Branch ................................ 0.329

4" 45˚ Elbow ........................................ 0.225

Additional Factors

Seasoned Filter ................................ 1.000

Total Static Pressure Loss ................ 4.444

Figure 33. Example list for totaling SP loss.

Note: When calculating static pressure loss to

determine if multiple lines can be left open at the same time, only include the main line numbers once.

5. Compare the total static pressure loss for that line to the closest CFM given in the Performance Curve section on the Machine Data Sheet (located toward the front of this manual). Example: go to the Model G0671 Data Sheet Performance Curve section (see Page 4) or see Figure 34 and find 4.4 on the Pressure axis, then go up the CFM axis to the closest value—approximately 3550 CFM, as shown in Figure 34.

The 3550 CFM ( machine.

Figure 34) for the static pres sure loss of the line connected to the router is well above the 220 CFM requirement of that

mACHINe dATA SHeeT

Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901

model G0671 4 HP dUST ColleCToR Performance Curve

4000 3750 3500 3250 3000 2750 2500 2250 2000 1750 1500 1250 1000 750 500 250 0

CFM

0 Closest CFM (3550) 1.0

2.0

4.4 SP Loss 3.0

4.0

5.0

6.0

7.0

8.0

9.0

STATIC PRESSURE (Inch/H2O)

10.0

11.0

12.0

13.0

14.0

47 1 / 4 " 47 1 / 4 " 47 1 / 47 4 1 / 4 " 47 5 / 8 " 47 5 / 8 " Ø23 5 / 8 " Ø23 5 / 8 " 6 5 / 8 " 6 5 / 8 " 101 1 / 8 " 101 1 / 8 " Ø23 5 / 8 " Ø23 5 / 8 " Figure 34. CFM for static pressure loss of line connected to G0671 dust collector & router.

3551.6

13.5

4 HP 220V 10" 14 1 / 2 "

CFM Amps

—If the CFM for your static pressure loss is above the requirement of the machine connected to the end of that branch line, then dust collection will most likely be

Air Speed (m/s)

the 30 33 29.5

32.1

27.5

30.5

24 27.1

make your system a reality.

21 23 16.8

19.5

12.5

13.5

Accessories section on Page 36 to start buying the components necessary to 3" 13.2

11 9.1

—If the CFM for your static pressure loss is below the requirement of the machine, then that line will not effectively collect the dust. You must then modify some of the factors in that line to reduce the static pressure loss. Some of the ways to do this include: 1) Installing larger duct, 2) reducing amount of flexible duct used, 3) increasing machine dust port size, 4) moving machine closer to dust collector to eliminate duct length, and 5) reducing 90˚ elbows or replacing them with 45˚ elbows 2" 484.3

13.5

8.6

4.5

31 3 / 8 " 31 3 / 8 " Ø10" Ø10" 73 7 / 8 " 73 7 / 8 "

Page 3 of 3

Model G0671/G0672/G0673 (Mfd. Since 6/17) -33-

System Grounding

Since plastic hose is abundant, relatively inex pensive, easily assembled and air tight, it is a very popular material for conveying dust from woodworking machines to the dust collector. We recommend using flexible hose (flex-hose) to con nect the woodworking machine to the dust collec tion system. However, plastic flex-hose and plastic duct are insulators, and dust particles moving against the walls of the plastic duct create static electrical build up. This charge will build until it discharges to a ground. If a grounding medium is not available to prevent static electrical build up, the electrical charge will arc to the nearest grounded source. This electrical discharge may cause an explosion and subsequent fire inside the system.

To protect against static electrical build up inside a non-conducting duct, a bare copper wire should be placed inside the duct along its length and grounded to the dust collector. You must also confirm that the dust collector is continuously grounded through the electrical circuit to the elec tric service panel. If you connect the dust collector to more than one machine by way of a non-conducting branching duct system and blast gates, the system must still be grounded as mentioned above. We recom mend inserting a continuous bare copper ground wire inside the entire duct system and attaching the wire to each grounded woodworking machine and dust collector.

Be sure that you extend the bare copper wire down all branches of the system. Do not forget to connect the wires to each other with wire nuts when two branches meet at a “Y” or “T” connection.

Always guard against static electrical build up by grounding all dust collection lines.

Ensure that the entire system is grounded. If using plastic blast gates to direct air flow, the grounding wire must be jumped ( Figure 35) around the blast gate without interruption to the grounding system.

Plastic Blast Gate Copper Ground Wire Metal Duct Figure 35. Ground jumper wire when using plastic blast gates and metal duct.

External Ground Wire Internal Ground Wire Ground Screw Flex-Hose Figure 36. Flex-hose grounded to machine.

We also recommend wrapping the outside of all plastic ducts with bare copper wire to ground the outside of the system against static electrical build up. Wire connections at Y’s and T’s should be made with wire nuts.

Attach the bare ground wire to each stationary woodworking machine and attach to the dust col lector frame with a ground screw, as shown in Figure 36. Ensure that each machine is continu ously grounded to the grounding terminal in your electric service panel.

-34 Model G0671/G0672/G0673 (Mfd. Since 6/17)

SECTION 5: OPERATIONS

To reduce your risk of serious injury, read this entire manual BEFORE using machine.

Basic Controls

This section covers the basic controls used during routine operations: ON Button: Starts the motor. OFF Button: Stops the motor.

Eye injuries, respiratory problems, or hear ing loss can occur while operating this tool. Wear personal protective equipment to reduce your risk from these hazards.

ON OFF

Keep hair, clothing, and jewelry away from mov ing parts at all times. Entanglement can result in death, amputation, or severe crushing injuries!

If you are not experienced with this type of machine, WE STRONGLY RECOMMEND that you seek additional training outside of this manual. Read books/magazines or get formal training before beginning any proj ects. Regardless of the content in this sec tion, Grizzly Industrial will not be held liable for accidents caused by lack of training.

Figure 37. ON/OFF button locations.

General

Operating your Model G0671/G0672/G0673 is simple and straightforward. Blast gates located at each of the woodworking machines control the airflow from the woodworking machine to the dust collector. If a machine is not being used, keep the blast gate closed to maintain higher levels of efficiency throughout the system. Model G0671/G0672/G0673 (Mfd. Since 6/17)

DO NOT use the dust collector for any other purpose besides collecting dust from connected woodworking machines. A dust collector should NEVER be used as a shop vacuum. For safest use, wear a respirator and use an air cleaner in addition to the dust collector.

-35-

ACCESSORIES

SECTION 6: ACCESSORIES

Installing unapproved accessories may cause machine to malfunction, resulting in serious personal injury or machine damage. To reduce this risk, only install accessories recommended for this machine by Grizzly.

NOTICE

Refer to our website or latest catalog for additional recommended accessories.

G0673036—Mag Switch 3-Phase 440V for Model G0673 Conversion H5293—4" Metal Duct Starter Kit H5295—5" Metal Duct Starter Kit H5297—6" Metal Duct Starter Kit

Save over 20% with this great starter kit. Includes: (2) machine adapters, (10) pipe clamps, (3) 5' straight pipes, (1) branch, (3) pipe hangers, (1) end cap, (3) adjustable nipples, (1) 90˚ elbow, and (1) 60˚ elbow.

H5294—4" Metal Duct Machine Addition Kit H5296—5" Metal Duct Machine Addition Kit H5298—6" Metal Duct Machine Addition Kit

Save over 20% with this great machine addition kit. Includes: (2) blast gates, (1) machine adapter, (10) pipe clamps, (2) pipe hangers, (2) 5' straight pipes, (2) adjustable nipples, (1) branch, and (1) 60˚ elbow.

Figure 39. Metal Duct Machine Addition Kit.

G6177—4" Metal Blast Gate G7340—5" Metal Blast Gate G7358—6" Metal Blast Gate H5234—7" Metal Blast Gate H5249—8" Metal Blast Gate H5259—9" Metal Blast Gate

Figure 38. Metal Duct Starter Kit.

Figure 40. Metal Blast Gate.

order online at www.grizzly.com

or call 1-800-523-4777

-36 Model G0671/G0672/G0673 (Mfd. Since 6/17)

Metal Elbows

These industrial metal elbows are available from 4"–8" with 90˚, 60˚, 45˚, or 30˚ curves. Also, avail able with a 90˚ long radius curve. Call (800) 523 4777 or visit www.grizzly.com for more informa tion and pricing.

Metal Branches

We carry many different branches, all designed to minimize airflow resistance.

90° 90° Long Radius 30° 45° 60° Figure 41. Metal elbow examples.

G6162—4" x 5' Straight Metal Pipe G7346—5" x 5' Straight Metal Pipe G7364—6" x 5' Straight Metal Pipe H5227—7" x 5' Straight Metal Pipe H5237—8" x 5' Straight Metal Pipe H5252—9" x 5' Straight Metal Pipe

These laser welded straight pipes ensure a super smooth internal seam. Ends easily clamp together for a sealed fit without screws or silicone.

Figure 43. Metal Branches.

Reducers & Adapters

We carry a multitude of reducers and elbows to cover most applications from 4" through 9".

Figure 42. Straight Metal Pipe.

Figure 44. Metal Reducers & Adapters.

G7979—Phase Converter for Model G0673

Add 3-phase multi-motor capability to your single phase electrical supply! Operate single or multiple motors, transformers, and resistance loads at 100% power and 95% efficiency while saving big dollars at cheaply-metered single-phase electrical rates.

H7216—5" x 5' Rigid Metal Flex Hose H7217—6" x 5' Rigid Metal Flex Hose H7218—7" x 5' Rigid Metal Flex Hose H7219—8" x 5' Rigid Metal Flex Hose H7220—9" x 5' Rigid Metal Flex Hose

This flex hose provides just enough flexibility to make difficult connections while still keeping the inside wall as smooth as possible to minimize static pressure loss.

order online at www.grizzly.com

or call 1-800-523-4777

Model G0671/G0672/G0673 (Mfd. Since 6/17) -37-

H4978—Deluxe Earmuffs - 27dB H4979—Twin Cup Hearing Protector - 29dB T20446—Ear Plugs 200 Pair - 31dB

Protect your hearing before its too late. Especially important if you or employees operate for hours at a time.

H4978 G0572—Hanging Air Filter With Remote

This Hanging Air Filter has a convenient remote control and features a three speed motor, auto matic shutoff timer and 1 micron inner filter and 5 micron outer filter. Air flow is 556, 702, and 1044 CFM.

H4979 T20446

Figure 45. Hearing protection assortment.

T10115—Benchtop Downdraft Table G3119—4" x 2 1 ⁄ 2 " Adapter

Want to stop making such a mess when sanding? This benchtop downdraft table is the perfect solu tion. Just connect the 2 1 ⁄ 2 " dust port in the back to a dust collector or Shop•Vac, and the suction will pull all dust and chips down into the table, keeping your work area tidy and clean.

G0572 Figure 47. G0572 Hanging Air Filter.

T10117—Big Mouth Dust Hood with Stand

Capture dust from any machine operation with this Big Mouth Dust Hood. Simply attach a 4" dust collection hose and adjust the hood right where you need it. The free standing base eliminates complicated machine set-ups and the tilting 16 3 ⁄ 8 " x 12 7 ⁄ 8 " hood adjusts from 23" to 43" high. Every shop needs one of these!

T10117 Figure 46. T10115 Benchtop Downdraft Table.

Figure 48. T10117 Big Mouth Dust Hood.

order online at www.grizzly.com

or call 1-800-523-4777

-38 Model G0671/G0672/G0673 (Mfd. Since 6/17)

SECTION 7: MAINTENANCE Bag Cleaning

Disconnect power to the machine when perform ing any maintenance, assembly or adjustments. Failure to do this may result in serious personal injury.

Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back.

Schedule

For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section.

Daily Check:

• Dust collector is completely powered down at the end of use.

• • • • Loose mounting bolts.

Worn switch or wires.

Any other condition that would hamper the safe operation of this machine.

Empty the lower collection bags before they become completely full.

Lubrication

Since all bearings are shielded and permanently lubricated, simply leave them alone until they need to be replaced. Do not lubricate them.

All dust collectors dis perse fine dust which may cause allergic reac tions or respiratory prob lems. Always wear a res pirator when operating your dust collector.

Empty the lower collection bags on a regular basis to maintain dust collection efficiency.

Always wear the appropriate respirator or dust mask and safety glasses when emptying the col lection bags. Small dust particles can escape the bags during emptying, causing them to become airborne and easily inhaled. This microscopic air borne dust is extremely unhealthy to breathe and can cause serious health problems.

While the Model G0671/G0672/G0673 excels at collecting the majority of wood dust produced by your machines, we always recommend the supplemental aid of a shop air filter. Air filters are designed to collect the smaller airborne dust par ticles that a dust collector bags cannot trap.

-39 Model G0671/G0672/G0673 (Mfd. Since 6/17)

SECTION 8: SERVICE

Review the troubleshooting and procedures in this section if a problem develops with your machine. If you need replacement parts or additional help with a procedure, call our Technical Support. Note: Please

gather the serial number and manufacture date of your machine before calling.

Troubleshooting

Motor & Electrical

Symptom Machine does not start or a breaker trips.

Machine stalls or is underpowered.

Machine has vibration or noisy operation.

Possible Cause 1. Plug/receptacle is at fault or wired incorrectly.

2. Motor connection wired incorrectly.

3. Thermal overload relay has tripped.

4. Contactor not getting energized/has burnt contacts.

5. Power supply is at fault/switched OFF.

6. Motor ON button or ON/OFF switch is at fault.

7. Centrifugal switch is at fault.

8. Wiring is open/has high resistance.

9. Motor is at fault.

1. Motor connection is wired incorrectly.

2. Plug/receptacle is at fault.

3. Motor bearings are at fault.

4. Motor has overheated.

5. Contactor not getting energized or has poor contacts.

6. Motor is at fault.

7. Centrifugal switch is at fault.

1. Motor or component is loose.

2. Motor fan is rubbing on fan cover.

3. Motor mount loose/broken.

4. Motor bearings are at fault.

5. Centrifugal switch.

Possible Solution 1. Test for good contacts; correct the wiring.

2. Correct motor wiring connections.

3. Turn cut-out dial to increase working amps and push the reset pin. Replace if tripped multiple times (weak relay).

4. Test for power on all legs and contactor operation. Replace unit if faulty.

5. Ensure hot lines have correct voltage on all legs and main power supply is switched ON.

6. Replace faulty ON button or ON/OFF switch.

7. Adjust/replace the centrifugal switch if available.

8. Check for broken wires or disconnected/corroded connections, and repair/replace as necessary. 9. Test/repair/replace.

1. Correct motor wiring connections.

2. Test for good contacts; correct the wiring.

3. Test by rotating shaft; rotational grinding/loose shaft requires bearing replacement.

4. Clean off motor, let cool, and reduce workload.

5. Test for power on all legs and contactor operation. Replace if faulty.

6. Test/repair/replace.

7. Adjust/replace centrifugal switch if available.

1. Inspect/replace stripped or damaged bolts/nuts, and re-tighten with thread locking fluid.

2. Replace dented fan cover; replace loose/damaged fan.

3. Tighten/replace.

4. Test by rotating shaft; rotational grinding/loose shaft requires bearing replacement.

5. Replace.

-40 Model G0671/G0672/G0673 (Mfd. Since 6/17)

Dust Collection Operation

SYMPTOM

Loud, repetitious noise, or excessive vibration coming from dust collector.

Dust collector does not adequately collect dust or chips; poor performance.

Sawdust being blown into the air from the dust collector.

POSSIBLE CAUSE

1. Dust collector is not on a flat surface and wobbles.

2. Impeller fan is damaged and unbalanced.

3. The motor mounting is loose.

4. Impeller is loose on the motor shaft.

5. Motor fan cover is dented, causing the motor fan to hit the cover while spinning.

1. Dust collection bag is full/filter bag is dirty.

2. There is a restriction in the duct line.

3. The dust collector is too far away from the point of suction, or there are too many sharp bends in the ducting.

4. The lumber is wet and not flowing through the dust lines smoothly.

5. There is a leak in the ducting, or a series of small leaks, or too many open ports.

6. There are not enough open branch lines at one time, thereby causing a velocity drop in the main line.

7. The ducting and ports are incorrectly sized.

8. The machine dust collection design is inadequate.

9. The dust collector is too small for the dust collection system.

1. Bag clamps, dust collection bag, or filter bag is not properly secured.

tight.

CORRECTIVE ACTION

1. Stabilize the dust collector.

2. Unplug dust collector, and inspect the impeller for dents, bends, loose fins. Replace impeller if any damage is found.

3. Make sure all fasteners on the dust collector are 4. Replace the motor and impeller as a set if the motor shaft and the impeller hub is damaged.

5. Replace motor fan cover.

1. Empty collection bag/clean or replace filter bag.

2. Remove dust line from dust collector inlet and unblock the restriction in the duct line. A plumbing snake may be necessary.

3. Relocate the dust collector closer to the point of suction, and rework ducting without sharp bends. Refer to Designing the System, beginning on Page 27.

4. Process lumber with less than 20% moisture content.

5. Rework the ducting to eliminate all leaks. Close dust ports for lines not being used. Refer to Designing the System on Page 27 for more solutions.

6. Open 1 or 2 more blast gates to different branch lines to allow the velocity in the main line to increase.

7. Reinstall correctly sized ducts and fittings. Refer to Designing the System on Page 27 for more solutions.

8. Use a dust collection nozzle on a stand.

9. Install a larger dust collector to power your dust collection system.

1. Reclamp the dust collection bag and air filter bag, making sure bag clamps are tight and completely over the bags.

Model G0671/G0672/G0673 (Mfd. Since 6/17) -41-

machine

SECTION 9: WIRING

These pages are current at the time of printing. However, in the spirit of improvement, we may make chang es to the electrical systems of future machines. Compare the manufacture date of your machine to the one stated in this manual, and study this section carefully.

If there are differences between your machine and what is shown in this section, call Technical Support at (570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine. An updated wiring diagram may be available. Note: Please gather the serial number and manufacture date of your

machine before calling. This information can be found on the main machine label.

Wiring Safety Instructions

SHOCK HAZARD. Working on wiring that is con nected to a power source is extremely dangerous. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, or death. Disconnect the power from the machine before servicing electrical com ponents!

WIRE/COMPONENT DAMAGE. Damaged wires or components increase the risk of serious per sonal injury, fire, or machine damage. If you notice that any wires or components are damaged while performing a wiring task, replace those wires or components.

MODIFICATIONS. Modifying the wiring beyond what is shown in the diagram may lead to unpre dictable results, including serious injury or fire. This includes the installation of unapproved after market parts.

MOTOR WIRING. The motor wiring shown in these diagrams is current at the time of printing but may not match your machine. If you find this to be the case, use the wiring diagram inside the motor junction box.

WIRE CONNECTIONS. All connections must be tight to prevent wires from loosening during machine operation. Double-check all wires dis connected or connected during any wiring task to ensure tight connections.

CAPACITORS/INVERTERS. Some capacitors and power inverters store an electrical charge for up to 10 minutes after being disconnected from the power source. To reduce the risk of being shocked, wait at least this long before working on capacitors.

CIRCUIT REQUIREMENTS. You MUST follow the requirements at the beginning of this manual when connecting your machine to a power source. EXPERIENCING DIFFICULTIES. If you are expe riencing difficulties understanding the information included in this section, contact our Technical Support at (570) 546-9663.

-42-

The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com.

Model G0671/G0672/G0673 (Mfd. Since 6/17)

G0671 Wiring Diagram

A Wt Bk Bk Bk Figure 49. G0671 MA-15 contactor.

Gn L1/1 L2/3 L3/5 7 SDE T1/2 MA-15 T2/4 T3/6 8 1/2 Wt 3/4

Set to 30

AMP 5/6 34 96 28 22 98 B Bk 95 Bk Bk Wt Bk Gn Gn Gn Bk Wt Figure 50. G0671 motor junction box.

Model G0671/G0672/G0673 (Mfd. Since 6/17) Wt Bk Gn Ground Rd Rd Rd Rd Rd Rd Run Capacitor 50MFD 300VAC Start Capacitor 600MFD 250VAC Gn Bk Wt Hot

MOTOR at 220V SINGLE-PHASE

GND

Locking Shut-Off Switch (As Recommended)

READ ELECTRICAL SAFETY ON PAGE 42!

-43-

G0672 Wiring Diagram

Figure 51. G0672 MA-30 contactor.

Start Capacitor Wt Bk Bk Bk A R/1/L1 S/3/L2 T/5/L3 21NC T1/2 MA-30 T2/4 T3/6 13 SDE 14 22NC 1/2 3/4 B

Set to 37

AMP 5/6 42 96 35 28 RA-30 98 Wt Bk 95 Bk Bk Wt Bk Gn Gn Gn Gn Bk Wt Figure 52. G0672 start capacitor.

Run Capacitors Start Capacitor 800MFD 250VAC Wt Bk Gn Ground Rd Rd Rd Rd Rd Rd Rd Run Capacitor 50MFD 250VAC Run Capacitor 50MFD 250VAC

MOTOR at 220V SINGLE-PHASE

Gn Ground Bk Hot Wt

Locking Shut-Off Switch (As Recommended)

-44 Figure 53. G0672 run capacitors.

READ ELECTRICAL SAFETY ON PAGE 42!

Model G0671/G0672/G0673 (Mfd. Since 6/17)

G0673 Wiring Diagram

MOTOR DIRECTION

If motor rotates in opposite direc tion, swap any two power source wires at the incoming terminals.

Ground Hot

3-PHASE 220 VAC

Hot Gn Rd Bk Wt Hot See

Figure 54 on Page 46.

Gn A Rd Bk Bk L1/1 Bk Wt Bk L2/3 L3/5 13 Bk Gn

220V MAGNETIC SWITCH ASSEMBLY 3-PHASE 440 VAC

DISCONNECT SWITCH (as recommended)

Ground Rd Hot Bk Hot Gn Wt Hot 1 L1 3 L2 5 L3 13 NO TECO CU 16 2 T1 4 T2 6 T3 14 NO ON Ground T1/2 T2/4 T3/6 1/2 Rd 3/4 Bk 14 B Bk Bk AMP 5/6 96 34 28 22 98 Wt Bk 95 Bk Gn

440V MAGNETIC SWITCH ASSEMBLY

TRIP IND.

TEST 97 NO 98 NO O R A OFF RESET M 95 NC 96 NC 2 T1 4 T2 6 T3 Gn MOTOR at 220V 3-PHASE 2 3 Wt Rd Bk Gn See

Figure 55 on Page 46.

1 MOTOR at 440V 3-PHASE Ground 5 9 4 8 6 7 2 3 Wt Rd Gn 1 Bk 6 9 5 8 4 7 Ground Model G0671/G0672/G0673 (Mfd. Since 6/17)

READ ELECTRICAL SAFETY ON PAGE 42!

-45-

G0673 Electrical Components

Figure 54. G0673 220V switch.

Figure 55. G0673 220V motor.

-46-

READ ELECTRICAL SAFETY ON PAGE 42!

Model G0671/G0672/G0673 (Mfd. Since 6/17)

20V2 19 1-1 1-2 1-3 1-4 1-5 1-6 1-7 18 19 38V2 28 1-8

SECTION 10: PARTS G0671 Parts Breakdown

16 16 14 20V2 13 6 19 29 17 15 30 10 11 9 17 7 8 12 17 15 17 40 31 32 33 30 5 4 1 2 39 3 41 21 26 22 36 22 34 35 24 23 21 27 40 27 26 25 37 29 18 28 19 38V2 42 33-2 33-2A 33-4 33-1 33-3 33-5 -47 Model G0671/G0672/G0673 (Mfd. Since 6/17)

G0671 Parts List

REF PART # DESCRIPTION

1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 2 3 4 5 6 7 8 9 10 11 12 P0671001 MOTOR 4HP, 220V, 1 PH P0671001-1 FAN COVER P0671001-2 FAN P0671001-3 S CAPACITOR COVER P0671001-4 S CAPACITOR 600M 250V X 1-3/4 X 3-7/8 P0671001-5 R CAPACITOR COVER P0671001-6 R CAPACITOR 50M 300V X 1-3/4 X 2-3/4 P0671001-7 JUNCTION BOX P0671001-8 CENTRIFUGAL SWITCH P0671002 HEX NUT 3/8-16 P0671003 P0671004 P0671005 P0671006 P0671007 P0671008 P0671009 P0671010 P0671011 P0671012 LOCK WASHER 3/8 KEY 6 X 6 X 25 MOTOR GASKET HEX BOLT 5/16-18 X 3/4 INLET COVER IMPELLER 14-1/2" HEX BOLT 3/8-16 X 1/2 CAP SCREW M6-1 X 20 FLAT WASHER 6MM COLLECTOR HOUSING 13 14 15 16 17 P0671013 P0671014 P0671015 P0671016 P0671017 PHLP HD SCR 10-24 X 3/8 INLET ADAPTER BAG HANGER LOWER SUPPORT BAG HANGER HEX BOLT 1/4-20 X 1/2 18 P0671018 COLLECTOR DRUM 19 P0671019 BAG CLAMP 20V2 P0671020V2 FILTER BAG 2.5 MICRON 23-5/8" X 47-1/4" V2.07.15

REF PART # DESCRIPTION

21 22 23 24 25 26 27 28 29 30 P0671021 P0671022 P0671023 P0671024 P0671025 P0671026 P0671027 P0671028 P0671029 P0671030 RIGHT LEG LEFT LEG HEX BOLT 5/16-18 X 2-1/2 HEX NUT 5/16-18 HEX BOLT 5/16-18 X 1/2 F/R LEG BRACE L/R LEG BRACE HEX BOLT 5/16-18 X 1 FLAT WASHER 5/16 HEX NUT 5/16-18 31 32 33 33-1 33-2 P0671031 P0671032 P0671033 MAGNETIC SWITCH PLATE PHLP HD SCR 10-24 X 1/2 MAGNETIC SWITCH P0671033-1 MAG SWITCH BACK COVER P0671033-2 CONTACTOR SDE MP-15 220V 33-2A P0671033-2A AUXILIARY CONTACTOR SWITCH 33-3 33-4 P0671033-3 OL RELAY SDE RA-30 21-35 P0671033-4 MAG SWITCH FRONT COVER 33-5 34 P0671033-5 PLASTIC COVER SCREW 11/32-16 X 3/4 P0671034 STRAIN RELIEF 35 36 37 P0671035 P0671036 P0671037 MOTOR CORD 12AWG X 3C POWER CORD 12AWG X 3C CASTER WITH BRAKE 38V2 P0671038V2 LOWER DUST BAG 23-5/8" X 54" V2.07.15

39 P0671039 HEX BOLT 3/8-16 X 1-1/4 40 41 42 P0671040 P0671041 P0671042 RUBBER GASKET FLAT WASHER 3/8 COMBO WRENCH 10 X 12MM -48 Model G0671/G0672/G0673 (Mfd. Since 6/17)

G0672 Parts Breakdown

20 19 1-1 1-2 1-4 18 1-5 19 1-6 1-7 38 28 1-8 16 16 20 14 13 6 19 17 15 30 29 10 11 9 17 7 8 12 17 15 17 21 30 40 5 4 1 31 32 26 39 3 41 22 2 36 33V3 34 35 24 23 22 21 27 40 27 26 37 25 29 18 28 19 38 42 33-2V2 33-6 33-4 33-1 33-3V2 33-5 Model G0671/G0672/G0673 (Mfd. Since 6/17) -49-

REF

1 1-1 1-2 1-4 1-5 1-6 1-7 1-8 2 3 16 17 18 19 20 21 4 5 6 7 8 9 10 11 12 13 14 15

PART #

P0672001 P0672001-1 P0672001-2 P0672001-4 P0672001-5 P0672001-6 P0672001-7 P0672001-8 P0672002 P0672003 P0672004 P0672005 P0672006 P0672007 P0672008 P0672009 P0672010 P0672011 P0672012 P0672013 P0672014 P0672015 P0672016 P0672017 P0672018 P0672019 P0672020 P0672021

G0672 Parts List

DESCRIPTION

MOTOR 5HP, 220V, 1 PH FAN COVER FAN S CAPACITOR 800M 250V 1-3/4 X 3-3/4 R CAPACITOR COVER R CAPACITOR 50M 250V 2 X 4-3/8 JUNCTION BOX CENTRIFUGAL SWITCH HEX NUT 3/8-16 LOCK WASHER 3/8 KEY 6 X 6 X 25 MOTOR GASKET HEX BOLT 5/16-18 X 3/4 INLET COVER IMPELLER 15" HEX BOLT 3/8-16 X 1/2 CAP SCREW M6-1 X 20 FLAT WASHER 6MM COLLECTOR HOUSING PHLP HD SCR 10-24 X 3/8 INLET ADAPTER BAG HANGER LOWER SUPPORT BAG HANGER HEX BOLT 1/4-20 X 1/2 COLLECTOR DRUM BAG CLAMP FILTER BAG 2.5 MICRON 23-5/8" X 70" RIGHT LEG

REF PART # DESCRIPTION

22 23 24 25 26 27 28 29 30 31 38 39 40 41 42 P0672022 P0672023 P0672024 P0672025 P0672026 P0672027 P0672028 P0672029 P0672030 P0672031 LEFT LEG HEX BOLT 5/16-18 X 2-1/2 HEX NUT 5/16-18 HEX BOLT 5/16-18 X 1/2 F/R LEG BRACE L/R LEG BRACE HEX BOLT 5/16-18 X 1 FLAT WASHER 5/16 HEX NUT 5/16-18 MAGNETIC SWITCH PLATE 32 33V3 33-1 P0672032 P0672033V3 P0672033-1 PHLP HD SCR 10-24 X 1/2 MAGNETIC SWITCH ASSY V3.06.17

MAG SWITCH BACK COVER 33-2V2 P0672033-2V2 CONTACTOR SDE MA-30 220V V2.06.17

33-3V2 P0672033-3V2 OL RELAY SDE RA-30 28-42A V2.01.13

33-4 P0672033-4 MAG SWITCH FRONT COVER 33-5 33-6 34 35 36 37 P0672033-5 P0672033-6 P0672034 P0672035 P0672036 P0672037 PLASTIC COVER SCREW 11/32-16 X 3/4 AUXILIARY CONTACTOR SWITCH STRAIN RELIEF MOTOR CORD 10AWG X 3C POWER CORD 10AWG X 3C CASTER WITH BRAKE P0672038 P0672039 P0672040 P0672041 P0672042 LOWER DUST BAG 23-5/8" X 54" HEX BOLT 3/8-16 X 1-1/4 RUBBER GASKET FLAT WASHER 3/8 COMBO WRENCH 10 X 12MM -50 Model G0671/G0672/G0673 (Mfd. Since 6/17)

20

G0673 Parts Breakdown

16 16 16 20 20 16 17 18 15 19 40 19 21 9 12 21 7 24 35 25 26 24 26 4 3 15 15 19 17 14 17 19 18 34 13 37 27 18 15 29 30 11 31 33 32 22 10 8 21 24 28 19 37 23 21 19 2 5 6 25 24 26 1 1-1 26 1-2 1-3 35 20 440V 36 220V 30-2 30-4 18 30-1 30-3 30-5 38 Model G0671/G0672/G0673 (Mfd. Since 6/17) -51-

G0673 Parts List

REF PART #

2 3 4 5 6 1 1-1 1-2 1-3 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

DESCRIPTION

P0673001 MOTOR 10HP, 220V, 3 PH P0673001-1 FAN COVER P0673001-2 FAN P0673001-3 JUNCTION BOX P0673002 P0673003 P0673004 P0673005 P0673006 HEX NUT 1/2"-12 LOCK WASHER 1/2 KEY 8 X 8 X 25 MOTOR GASKET HEX BOLT 5/16-18 X 3/4 P0673007 P0673008 P0673009 P0673010 P0673011 P0673012 P0673013 P0673014 P0673015 P0673016 P0673017 P0673018 P0673019 P0673020 P0673021 P0673022 P0673023 P0673024 INLET COVER HEX BOLT 1/2 X 1-1/2 IMPELLER 17" HEX BOLT 3/8-16 X 1-1/2 FLAT WASHER 6MM CAP SCREW M6-1 X 20 COLLECTOR HOUSING INLET ADAPTER BAG HANGER LOWER SUPPORT BAG HANGER HEX BOLT 1/4-20 X 1/2 COLLECTOR DRUM BAG CLAMP FILTER BAG 2.5 MICRON 23-5/8" X 70" LEG HEX BOLT 5/16-18 X 2-1/2 HEX NUT 5/16-18 LEG BRACE

REF PART #

25 26 27 28 29 30 30-1 30-2 30-3 30-4 30-5 31 32 33 34 35 36 37 38 40 51 52 53 54 55 56 56

DESCRIPTION

P0673025 P0673026 P0673027 P0673028 HEX BOLT 5/16-18 X 1/2 CASTER WITH BRAKE HEX BOLT 5/16-18 X 1 HEX NUT 5/16-18 P0673029 P0673030 PHLP HD SCR 10-24 X 1/2 MAGNETIC SWITCH ASSY 220V P0673030-1 MAG SWITCH BACK COVER P0673030-2 CONTACTOR SDE MP-30 220V 3PH P0673030-3 OL RELAY SDE RA-30 21-35 P0673030-4 MAG SWITCH FRONT COVER P0673030-5 PLASTIC COVER SCREW 11/32-16 X 3/4 P0673031 P0673032 STRAIN RELIEF MOTOR CORD 10AWG X 4C P0673033 P0673034 P0673035 P0673036 POWER CORD 10AWG X 4C PHLP HD SCR 10-24 X 3/8 LOWER DUST BAG 23-5/8" X 54" MAGNETIC SWITCH ASSY 440V P0673037 P0673038 P0673040 P0673051 P0673052 P0673053 P0673054 P0673055 P0673056 P0673056 FLAT WASHER 5/16" COMBO WRENCH 10 X 12MM RUBBER GASKET MACHINE ID LABEL GRIZZLY NAMEPLATE EAR PROTECTION 2" X 3-5/16"H GLASSES/RESPIRATOR READ MANUAL-VERTICAL NS 7/05 GRIZZLY GREEN TOUCH-UP PAINT GRIZZLY GREEN TOUCH-UP PAINT -52 Model G0671/G0672/G0673 (Mfd. Since 6/17)

56 55

G0671

50

Label Placement

G0672

50 51 56 51 56 54 53

G0673

52 51 55 52 54 53

REF PART #

50 51 51 51 52 52 53 54 55 56 P0671050 P0671051 P0672051 P0673051 P0671052 P0673052 P0671053 P0671054 P0671055 P0671056

DESCRIPTION

HANDS INLET WARNING (G0671, G0672) MACHINE ID LABEL (G0671) MACHINE ID LABEL (G0672) MACHINE ID LABEL (G0673) GRIZZLY NAMEPLATE (G0671, G0672) GRIZZLY NAMEPLATE (G0673) EAR PROTECTION 2" X 3-5/16"H GLASSES/RESPIRATOR READ MANUAL-VERTICAL NS 7/05 GRIZZLY GREEN TOUCH-UP PAINT 55 52 54 53

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

Model G0671/G0672/G0673 (Mfd. Since 6/17) -53-

WARRANTY CARD

Name _____________________________________________________________________________ Street _____________________________________________________________________________ City _______________________ State _________________________ Zip _____________________ Phone # ____________________ Email _________________________________________________ Model # ____________________ Order # _______________________ Serial # __________________

The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services.

Of course, all information is strictly confidential.

1. How did you learn about us?

____ Advertisement ____ Card Deck ____ Friend ____ Website ____ Catalog ____ Other: 2. Which of the following magazines do you subscribe to?

____ Cabinetmaker & FDM ____ Family Handyman ____ Hand Loader ____ Handy ____ Home Shop Machinist ____ Journal of Light Cont.

____ Live Steam ____ Model Airplane News ____ Old House Journal ____ Popular Mechanics ____ Popular Science ____ Popular Woodworking ____ Precision Shooter ____ Projects in Metal ____ RC Modeler ____ Rifle ____ Shop Notes ____ Shotgun News ____ Today’s Homeowner ____ Wood 3. What is your annual household income?

____ $20,000-$29,000 ____ $50,000-$59,000 ____ $30,000-$39,000 ____ $60,000-$69,000 ____ Wooden Boat ____ Woodshop News ____ Woodsmith ____ Woodwork ____ Woodworker West ____ Woodworker’s Journal ____ Other: ____ $40,000-$49,000 ____ $70,000+ 4. What is your age group?

____ 20-29 ____ 50-59 ____ 30-39 ____ 60-69 ____ 40-49 ____ 70+ 5. How long have you been a woodworker/metalworker?

____ 0-2 Years ____ 2-8 Years ____ 8-20 Years 6. How many of your machines or tools are Grizzly?

____ 0-2 ____ 3-5 ____ 6-9 ____ 20+ Years ____ 10+ 7. Do you think your machine represents a good value? 8. Would you recommend Grizzly Industrial to a friend? _____Yes _____Yes _____No _____No 9. Would you allow us to use your name as a reference for Grizzly customers in your area?

Note: We never use names more than 3 times. _____Yes _____No 10. Comments: _____________________________________________________________________

_________________________________________________________________________________ _________________________________________________________________________________ _________________________________________________________________________________

FOLD ALONG DOTTED LINE

GRIZZLY INDUSTRIAL, INC.

P.O. BOX 2069 BELLINGHAM, WA 98227-2069

FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here

WARRANTY AND RETURNS WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any par ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special, or consequential damages arising from the use of our products.

To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the carton. We will not accept any item back without this number. Proof of purchase must accompany the merchandise. The manufacturers reserve the right to change specifications at any time because they constantly strive to achieve better quality equipment. We make every effort to ensure that our products meet high quality and durability standards and we hope you never need to use this warranty.

Please feel free to write or call us if you have any questions about the machine or the manual. Thank you again for your business and continued support. We hope to serve you again soon.

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement