Grizzly G0692 Owner's manual

Grizzly G0692 Owner's manual
MODEL G0692
14" DRY CUT METAL SAW
OWNER'S Manual
(for Machines manufactured from 11/08 and later)
Copyright © February, 2009 By Grizzly Industrial, Inc. Revised april, 2014 (tr)
Warning: No portion of this manual may be reproduced in any shape
Or form without the written approval of Grizzly Industrial, inc.
#JBCR11500 printed IN TAIWAN
This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and comprehension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
•
•
•
Lead from lead-based paints.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.
Table of Contents
INTRODUCTION................................................ 2
Manual Accuracy............................................ 2
Contact Info.................................................... 2
Machine Description....................................... 2
Identification.................................................... 3
Machine Data Sheet....................................... 4
SECTION 1: SAFETY........................................ 6
Safety Instructions for Machinery................... 6
Safety Instructions for Metal Cutting Saws..... 8
SECTION 2: CIRCUIT REQUIREMENTS......... 9
110V Operation............................................... 9
SECTION 3: SETUP........................................ 10
Needed for Setup.......................................... 10
Unpacking..................................................... 10
Inventory....................................................... 10
Site Considerations....................................... 11
Blade Installation.......................................... 11
Test Run....................................................... 11
SECTION 4: OPERATIONS............................ 12
Basic Controls............................................... 12
Vise Fence.................................................... 13
Vise Quick Release...................................... 14
Chip Collection Tray..................................... 14
Switch Lock-out............................................ 14
Blade Terminology........................................ 15
Blade Pitch.................................................... 15
Blade Feed Rate........................................... 16
Blade Break-in.............................................. 17
Changing Blade............................................ 17
Cutting Procedures....................................... 19
Cutting Tips................................................... 19
General Machine Tips................................... 19
SECTION 5: ACCESSORIES.......................... 20
SECTION 6: MAINTENANCE.......................... 22
Schedule....................................................... 22
Cleaning........................................................ 22
Unpainted Cast Iron...................................... 22
Lubrication.................................................... 22
SECTION 7: SERVICE.................................... 23
Troubleshooting............................................ 23
Motor Brushes.............................................. 25
SECTION 8: WIRING....................................... 26
Wiring Safety Instructions............................. 26
Wiring Diagram............................................. 27
SECTION 9: PARTS........................................ 28
Parts Breakdown.......................................... 28
Parts List....................................................... 29
Warning Labels............................................. 30
WARRANTY AND RETURNS......................... 33
INTRODUCTION
Manual Accuracy
Contact Info
We are proud to offer this manual with your new
machine! We've made every effort to be exact
with the instructions, specifications, drawings, and
photographs of the machine we used when writing this manual. However, sometimes errors do
happen and we apologize for them.
We stand behind our machines. If you have any
service questions, parts requests or general questions about the machine, please call or write us at
the location listed below.
Also, owing to our policy of continuous improvement, your machine may not exactly match the
manual. If you find this to be the case, and the difference between the manual and machine leaves
you in doubt, check our website for the latest
manual update or call technical support for help.
Before calling, find the manufacture date of your
machine by looking at the date stamped into the
machine ID label (see below). This will help us
determine if the manual version you received
matches the manufacture date of your machine.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
If you have any comments regarding this manual,
please write to us at the address below:
Grizzly Industrial, Inc.
/O Technical Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Email: [email protected]
C
Machine Description
Manufacture Date
of Your Machine
For your convenience, we post all available manuals and manual updates for free on our website
at www.grizzly.com. Any updates to your model
of machine will be reflected in these documents
as soon as they are complete.
-2-
This 14" Dry Cut Metal Saw is used to cut thinwalled metal workpieces accurately, efficiently,
and safely. This saw is advantageous over a
typical metal-cutting bandsaw in that the cuts
produced are cleaner, more accurate, and can be
made much faster.
An adjustable vise holds the workpiece securely
and ensures proper positioning of the workpiece
relative to the blade.
The cutting angle is adjustable from 0° to 45° and
is measured by a scale located on the saw base.
Model G0692 (Mfg. 11/08 and Later)
Identification
Trigger Switch
Saw Handle
Arbor Lock
Button
Gearbox
Motor
Blade Guard
Lock-down
Knob
Vise Quick
Release Lever
Vise Handle
Vise Angle
Lock Lever
Vise
Fence
Vise Clamp
Figure 1. Identification.
Model G0692 (Mfg. 11/08 and Later)
-3-
Machine Data Sheet
maCHINe data
SHeet
Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901
model G0692
14" dry Cut metal Saw
Product Dimensions:
Weight ............................................................................................................................................................................. 50 lbs.
Length/Width/Height ................................................................................................................................. 243⁄4" x 163⁄4" x 19 5⁄8"
Foot Print (Length/Width) ....................................................................................................................................... 19 1⁄8" x 12 1⁄2"
Shipping Dimensions:
Type ................................................................................................................................................................... Cardboard Box
Content.......................................................................................................................................................................... Machine
Weight .............................................................................................................................................................................. 58 lbs.
Length/Width/Height............................................................................................................................................ 22" x 18" x 21"
Electrical:
Switch................................................................................................................................................. Trigger Switch on Handle
Switch Voltage ................................................................................................................................................................... 110V
Cord Length ..........................................................................................................................................................................8 ft.
Cord Gauge .................................................................................................................................................................. 14 AWG
Minimum Circuit Size ........................................................................................................................................................... 20A
Plug Type Included .................................................................................................................................................. NEMA 1-15
Motor:
Type ...................................................................................................................................................................... Universal DC
Horsepower .........................................................................................................................................................................4 HP
Voltage ............................................................................................................................................................................... 110V
Phase .................................................................................................................................................................... Single-Phase
Amps .................................................................................................................................................................................... 15A
Speed ......................................................................................................................................................................23,500 RPM
Cycle ................................................................................................................................................................................. 60 Hz
Number Of Speeds ...................................................................................................................................................................1
Power Transfer ............................................................................................................................................................. Gearbox
Bearings ............................................................................................................................... Shielded and Permanently Sealed
Model G0692
-4-
Page 1 of 2
Model G0692 (Mfg. 11/08 and Later)
Main Specifications:
Operation Information
Blade Speed .....................................................................................................................................................1300 RPM
Blade Size ................................................................................................................................................................... 14"
Arbor Size ...................................................................................................................................................................... 1"
Cutting Capacities
Angle Cuts ..........................................................................................................................................................45° − 90°
Vise Jaw Depth .......................................................................................................................................................... 8 1⁄8"
Vise Jaw Height.......................................................................................................................................................... 2 3⁄4"
Maximum Capacity Square @ 90° ............................................................................................................................. 4 1⁄2"
Maximum Capacity Rectangular @ 90° ..................................................................................................... 3 7⁄8"W x 6 1⁄4"H
Maximum Capacity Round @ 90° .............................................................................................................................. 4 7⁄8"
Maximum Capacity Square @45° .............................................................................................................................. 3 1⁄8"
Maximum Capacity Rectangular @ 45° ..................................................................................................... 3 1⁄8"W x 3 1⁄2"H
Maximum Capacity Round @ 45° .............................................................................................................................. 3 1⁄8"
Construction
Table Construction ............................................................................................................................................Aluminum
Saw Wheel Cover......................................................................................................................................................Steel
Saw Wheel Guard .................................................................................................................................................. Plastic
Body Construction .............................................................................................................................................Aluminum
Paint ................................................................................................................................................................... Urethane
Other Specifications:
Country Of Origin ............................................................................................................................................................ Taiwan
Warranty........................................................................................................................................................................... 1 Year
Serial Number Location ........................................................................................................Machine ID Label on Body Frame
Features:
Spring Assisted Return
Adjustable Angle from 45° to 90°
Model G0692
Model G0692 (Mfg. 11/08 and Later)
Page 2 of 2
-5-
SECTION 1: SAFETY
for Your Own Safety, Read instruction
Manual before Operating This Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.
indicates an imminently hazardous situation which, if not avoided,
WiLL result in death or serious injury.
indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. it may also be used to alert
against unsafe practices.
notice
This symbol is used to alert the user to useful information about
proper operation of the machine.
Safety Instructions for Machinery
OWNER’S MANUAL. read and understand this
owner’s manual beFore using machine.
TRAiNED OpERATORS ONLY. untrained operators have a higher risk of being hurt or killed.
only allow trained/supervised people to use this
machine. When machine is not being used, disconnect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially
around children. Make workshop kid proof!
DANGEROUS ENviRONMENTS. do not use
machinery in areas that are wet, cluttered, or have
poor lighting. operating machinery in these areas
greatly increases the risk of accidents and injury.
MENTAL ALERTNESS REQUiRED. Full mental
alertness is required for safe operation of machinery. never operate under the influence of drugs or
alcohol, when tired, or when distracted.
-6-
ELECTRiCAL EQUipMENT iNJURY RiSKS. you
can be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. to reduce this risk, only allow qualified
service personnel to do electrical installation or
repair work, and always disconnect power before
accessing or exposing electrical equipment.
DiSCONNECT pOWER fiRST. always disconnect machine from power supply beFore making
adjustments, changing tooling, or servicing machine.
this prevents an injury risk from unintended startup
or contact with live electrical components.
EYE pROTECTiON. always wear ansi-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. everyday
eyeglasses are not approved safety glasses.
Model G0692 (Mfg. 11/08 and Later)
WEARiNG pROpER AppAREL. do not wear
clothing, apparel or jewelry that can become
entangled in moving parts. always tie back or
cover long hair. Wear non-slip footwear to avoid
accidental slips, which could cause loss of workpiece control.
hAzARDOUS DUST. dust created while using
machinery may cause cancer, birth defects, or
long-term respiratory damage. be aware of dust
hazards associated with each workpiece material,
and always wear a niosh-approved respirator to
reduce your risk.
hEARiNG pROTECTiON. always wear hearing protection when operating or observing loud
machinery. extended exposure to this noise
without hearing protection can cause permanent
hearing loss.
REMOvE ADJUSTiNG TOOLS. tools left on
machinery can become dangerous projectiles
upon startup. never leave chuck keys, wrenches,
or any other tools on machine. always verify
removal before starting!
USE CORRECT TOOL fOR ThE JOb. only use
this tool for its intended purpose—do not force
it or an attachment to do a job for which it was
not designed. never make unapproved modifications—modifying tool or using it differently than
intended may result in malfunction or mechanical
failure that can lead to personal injury or death!
AWKWARD pOSiTiONS. Keep proper footing
and balance at all times when operating machine.
do not overreach! avoid awkward hand positions
that make workpiece control difficult or increase
the risk of accidental injury.
ChiLDREN & bYSTANDERS. Keep children and
bystanders at a safe distance from the work area.
stop using machine if they become a distraction.
GUARDS & COvERS. guards and covers reduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged, and working correctly.
Model G0692 (Mfg. 11/08 and Later)
fORCiNG MAChiNERY. do not force machine.
it will do the job safer and better at the rate for
which it was designed.
NEvER STAND ON MAChiNE. serious injury
may occur if machine is tipped or if the cutting
tool is unintentionally contacted.
STAbLE MAChiNE. unexpected movement during operation greatly increases risk of injury or
loss of control. before starting, verify machine is
stable and mobile base (if used) is locked.
USE RECOMMENDED ACCESSORiES. Consult
this owner’s manual or the manufacturer for recommended accessories. using improper accessories will increase the risk of serious injury.
UNATTENDED OpERATiON. to reduce the
risk of accidental injury, turn machine off and
ensure all moving parts completely stop before
walking away. never leave machine running
while unattended.
MAiNTAiN WiTh CARE. Follow all maintenance
instructions and lubrication schedules to keep
machine in good working condition. a machine
that is improperly maintained could malfunction,
leading to serious personal injury or death.
ChECK DAMAGED pARTS. regularly inspect
machine for any condition that may affect safe
operation. immediately repair or replace damaged
or mis-adjusted parts before operating machine.
MAiNTAiN pOWER CORDS. When disconnecting cord-connected machines from power, grab
and pull the plug—not the cord. pulling the cord
may damage the wires inside. do not handle
cord/plug with wet hands. avoid cord damage by
keeping it away from heated surfaces, high traffic
areas, harsh chemicals, and wet/damp locations.
EXpERiENCiNG DiffiCULTiES. if at any time
you experience difficulties performing the intended operation, stop using the machine! Contact our
technical support at (570) 546-9663.
-7-
Safety Instructions for Metal Cutting Saws
1.BLADE CONDITION. Do not operate with
a dull, cracked or badly worn blade. A damaged blade could break apart during use,
resulting in serious personal injury. Inspect
blades for cracks and missing teeth before
each use.
7.
ATTENTION TO WORK AREA. Never
leave a machine running and unattended.
Pay attention to the actions of others in the
area to avoid unintended accidents.
8.
MAINTENANCE/SERVICE. To reduce
the risk of injury from accidental startup,
all inspections, adjustments, and maintenance are to be done with the power
OFF and the machine disconnected from
power. Wait for all moving parts to come
to a complete stop.
9.
Hearing Protection & Hazards.
Noise generated by blade and workpiece
vibration, material handling, and power
transmission can cause permanent hearing loss over time and interfere with communication and audible signals.
2.HAND PLACEMENT. Never position fingers or thumbs in line with the cut. Hands
could be crushed in vise or from falling
machine components.
3.
ENTANGLEMENT HAZARDS. Do not
operate this saw without blade guard in
place. Loose clothing, jewelry, long hair
and work gloves can be drawn into working
parts.
4.BLADE REPLACEMENT. When replacing blades, disconnect the machine from
power to reduce the risk of injury from accidental startup.
5.
LOSS OF STABILITY. Unsupported
workpieces may jeopardize machine stability and cause the machine to tip and fall
which could cause serious injury.
6.FIRE HAZARD. If cutting magnesium, DO
NOT allow magnesium chips to build up.
Magnesium chips are extremely flammable
and can catch fire and burn at very high
temperatures
10. Hot Surfaces. Contact with hot surfaces from machine components, ejections of hot chips, and the workpiece itself
can cause burns.
11. WORKPIECE HANDLING. Always support the workpiece with table, vise, or
some type of support fixture to maintain
control over the workpiece during the cut.
Flag long pieces to avoid a tripping hazard.
Never hold the workpiece with your hands
during a cut.
No list of safety guidelines can be complete. Every shop environment is different. Like all
machines there is danger associated with the Model G0692. Accidents are frequently caused by
lack of familiarity or failure to pay attention. Use this machine with respect and caution to lessen
the possibility of operator injury. If normal safety precautions are overlooked or ignored, serious
personal injury may occur.
-8-
Model G0692 (Mfg. 11/08 and Later)
SECTION 2: CIRCUIT REQUIREMENTS
110V Operation
Serious personal injury could occur if you
connect the machine to power before completing the setup process. DO NOT connect
the machine to the power until instructed
later in this manual.
Power Connection Device
The Model G0692 comes with a NEMA 1-15 plug,
similar to Figure 2, to connect the machine to
power.
5-15 Receptacle
1-15 Plug
Electrocution or fire could
result if machine is not
installed in compliance
with electrical codes.
Compliance MUST be verified by a qualified electrician!
Full Load Amperage Draw
This machine draws the following amps under
maximum load:
Amp Draw............................................... 15 Amps
Hot
Neutral
Figure 2. Typical 1-15 plug and 5-15 receptacle.
Extension Cords
We do not recommend using extension cords, but
if you find it absolutely necessary:
•Use at least a 14 gauge cord that does not
exceed 50 feet in length!
•A qualified electrician MUST size cords over
50 feet long to prevent motor damage.
Power Supply Circuit Requirements
The power supply circuit for your machine MUST
be grounded and rated for the amperage given
below. Never replace a circuit breaker on an existing circuit with one of higher amperage without
consulting a qualified electrician to ensure compliance with wiring codes. If you are unsure about
the wiring codes in your area or you plan to
connect your machine to a shared circuit, consult a qualified electrician.
Minimum Circuit Size.............................. 20 Amps
Model G0692 (Mfg. 11/08 and Later)
-9-
SECTION 3: SETUP
Inventory
This machine presents
serious injury hazards
to untrained users. Read
through this entire manual to become familiar with
the controls and operations before starting the
machine!
Wear safety glasses during the entire setup process!
The following is a description of the main components shipped with your machine. Lay the components out to inventory them.
Container 1: (Figure 3)
Qty
A. Saw Unit...................................................... 1
B. Hex Wrench 8mm........................................ 1
A
Needed for Setup
Description
Qty
•
14" Saw Blade (Model T20920)................... 1
•Safety Glasses.......................................1 Pr.
•Shop Rags & Solvent Cleaner.....As needed
Unpacking
B
Figure 3. Machine inventory.
If any nonproprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Your machine was carefully packaged for safe
transportation. Remove the packaging materials
from around your machine and inspect it. If you
discover the machine is damaged, please immediately call Customer Service at (570) 546-9663
for advice.
Save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
When you are completely satisfied with the condition of your shipment, inventory the contents.
-10-
Model G0692 (Mfg. 11/08 and Later)
Site Considerations
Workbench Load
Refer to the Machine Data Sheet for the weight
and footprint specifications of your machine.
Some workbenches may require additional reinforcement to support both the machine and
workpiece.
Blade Installation
To install the blade on your new machine, perform
the procedures for Changing Blade on Page 17,
omitting the removal of the old blade, then return
to Test Run, below.
Test Run
Placement Location
Consider existing and anticipated needs, size of
material to be processed through each machine,
and space for auxiliary stands, work tables or
other machinery when establishing a location for
your new machine. See Figure 4 for the minimum
working clearances.
Once the assembly is complete, test run your
machine to make sure it runs properly.
If, during the test run, you cannot easily locate
the source of an unusual noise or vibration, stop
using the machine immediately, then review the
Troubleshooting on Page 23.
If you still cannot remedy a problem, contact our
Tech Support at (570) 546-9663 for assistance.
To test run the machine:
14"
1.
Make sure you have read the safety instructions at the beginning of the manual and that
the machine is set up properly.
2.
Make sure all tools and objects used during
setup are cleared away from the machine.
3.
Connect the machine to the power source.
13"
Figure 4. Minimum working clearances.
Children and visitors may be
seriously injured if unsupervised around this machine.
Lock entrances to the shop
or disable start switch or
power connection to prevent
unsupervised use.
4.Pull the trigger switch to turn the saw ON.
5.Listen and watch for abnormal noises or
actions. The machine should run smoothly
with little or no vibration or rubbing noises.
—Strange or unusual noises must be investigated and corrected before operating the
machine further. Always disconnect the
machine from power when investigating or
correcting problems.
6.Release the trigger switch to turn the machine
OFF.
Model G0692 (Mfg. 11/08 and Later)
-11-
SECTION 4: OPERATIONS
Basic Controls
To reduce the risk of
serious injury when using
this machine, read and
understand this entire
manual before beginning
any operations.
Use the descriptions and figures below to become
familiar with the basic controls of your machine.
Trigger Switch: Turns the motor ON, spinning
the blade.
Saw Handle: Lowers the saw into the workpiece.
Damage to your eyes, lungs, and ears could
result from using this machine without
proper protective gear. Always wear safety
glasses, a respirator, and hearing protection
when operating this machine.
Saw Handle
Trigger Switch
Figure 5. Control box.
Loose hair, clothing, or
jewelry could get caught
in machinery and cause
serious personal injury.
Keep these items away
from moving parts at all
times to reduce this risk.
NOTICE
Vise Handle: Opens and closes the vise jaws to
clamp the workpiece.
Vise Angle Lock Lever: Locks the angle of the
vise fence.
Vise Location Lock Lever: Locks the position of
the vise fence for proper workpiece alignment.
Vise Location
Lock Lever (out
of view)
If you have never used this type of machine
or equipment before, We strongly recommend that you read books, review
industry trade magazines, or get formal
training before beginning any projects.
Regardless of the content in this section,
Grizzly Industrial will not be held liable for
accidents caused by lack of training.
Vise Angle Lock
Lever
Vise Handle
Figure 6. Vise controls.
-12-
Model G0692 (Mfg. 11/08 and Later)
Vise Fence
For optimal cutting results, the center-line of the
blade must be as close as possible to the centerline of the workpiece. The workpiece alignment is
determined by both the position and the angle of
the vise fence. Since the position and the angle
of the fence are related, both must be adjusted at
the same time.
To adjust the vise fence:
1.
Workpiece
Vice Fence
Machine Base
DISCONNECT SAW FROM POWER!
2.Loosen the vise angle lock lever and the vise
location lock lever (Figure 7).
Vise Location
Lock Lever
Blade
Figure 8. Blade/workpiece alignment.
5.Double check that the vise fence is still set
for the desired angle of cut, then tighten both
lock levers.
Vise Fence
Always turn the saw OFF and allow the blade
to come to a complete stop before using the
vise! Failure to follow this caution may lead
to injury.
Vise Angle Lock
Lever
Figure 7. Vise fence.
3.
4.
Place the workpiece against the vise fence,
then, using the scale as a guide, set the
approximate desired angle of cut.
Use the chart shown in Figure 9 as a guide to
quickly position the workpiece between the vise
jaws correctly and to avoid slipping during a cut.
DO NOT CUT STEEL THAT IS STACKED OR
BUNDLED. One or more workpieces will slip and
damage the saw blade.
NOT
RECOMMENDED
RECOMMENDED
While maintaining the angle of the vise fence,
slide the fence along the base until the centerline of the workpiece approximately matches
the center-line of the saw (Figure 8).
Note: Because the center-line of the saw
changes as the saw arm moves, it is necessary to lower the saw for proper alignment.
Check for proper alignment periodically as
you adjust the fence position.
Figure 9. Vise holding chart.
Model G0692 (Mfg. 11/08 and Later)
-13-
Vise Quick Release
Chip Collection Tray
The Model G0692 is equipped with a quick release
on the vise leadscrew. This allows for rapid adjustments for a variety of workpiece dimensions.
The Model G0692 has a chip collection tray to
catch most of the chips produced during cutting.
Periodically slide it out the back and dispose of
the chips (Figure 11).
To use the vise quick release:
1.
Move the vise quick release lever to the left
("loose") position. This releases the leadscrew
and allows the vise clamp to slide as needed
(Figure 10).
Vise Quick
Release Lever
Chip Tray
Figure 11. Chip collection tray.
Leadscrew
Vise Handle
Figure 10. Vise quick release lever.
2.Slide the vise clamp to the approximate
location needed, then move the vise quick
release lever to the right ("tight") position.
This engages the leadscrew.
Switch Lock-out
To prevent unauthorized use of the saw, it can
be locked in the off position by placing a padlock
through the hole in the trigger switch (Figure
12).
3.Use the vise handle to tighten and loosen
the vise clamp as needed to secure the
workpiece.
Trigger Switch
Padlock
(Not Included)
Figure 12. Switch lockout.
-14-
Model G0692 (Mfg. 11/08 and Later)
Blade Terminology
Blade Pitch
Selecting the right blade for the cut requires an
understanding of various blade characteristics.
The most important consideration when selecting
a blade is blade pitch, which is typically measured
in "teeth per inch" (TPI). Proper TPI for any cut
depends on the cross-section size and wall thickness of the workpiece.
Blade Terminology
B
D
C
F
A
If the blade pitch is too coarse for the cut, there
will be too few teeth making the cut at any given
time. This results in broken blade teeth and rough
cuts due to excessive strain applied to both the
blade and the workpiece (Figure 14). Use a
blade pitch that keeps at least three teeth in the
workpiece at any time.
E
G
Blade
(TPI Too Coarse)
Figure 13. Blade terminology.
A. Blade Size (Diameter): The overall diameter
of the blade. The Model G0692 uses 14"
blades.
B. Pitch: The distance from the tip of one tooth
to the tip of the next. Typically given in Teeth
Per Inch (TPI).
C. Gullet: The shallow area between the tips of
the teeth.
D. Front Rake Angle: The measurement of the
angle formed between the tip of the blade
tooth and a line tangent to the perimeter of
the blade.
E.
F.
Broken
Tooth Tip
Workpiece
Figure 14. TPI too coarse for workpiece.
Conversely, if the blade pitch is too fine for the
cut, teeth will remain in the workpiece and remove
more material than the blade gullet can hold. This
buildup of chips prevents the teeth from cutting
effectively and results in poor cutting efficiency, overheating, and rapid rounding-off of teeth
(FIgure 15).
Rear Rake Angle: The measurement of the
angle formed between the face of the tooth
and the diameter.
Tooth Depth: The distance from the tip of
the tooth to the bottom of the corresponding
gullet.
G. Kerf: The width of the cut created by the
blade.
Blade
(TPI Too Fine)
Gullet
Excessive
Chip Buildup
Workpiece
Figure 15. TPI too fine for workpiece.
Model G0692 (Mfg. 11/08 and Later)
-15-
Similarly, if the workpiece is a soft metal such as
aluminum, each tooth will remove more material
and rapidly fill the blade gullet. For this reason,
use a blade with fewer TPI on soft metals.
An additional problem with an overly fine-pitched
blade is that the pressure each tooth exerts on the
workpiece is reduced. This limits the cutting ability
of the teeth and also results in a buildup of heat
and inefficient cuts.
The ideal blade pitch is one that doesn't overload
individual teeth (too coarse) and avoids excessive
chip buildup in the gullet (too fine) (Figure 16).
Blade
(Correct TPI
For Workpiece)
Gullet
Chips
Blade Feed Rate
Blade feed rate refers to the speed at which the
blade cuts through a workpiece. On the Model
G0692, feed rate is controlled by the amount
of pressure exerted on the handle by the user.
Pulling hard on the lever will result in a greater
feed rate, whereas only pulling lightly will result in
a very slow feed rate.
Cutting with a feed rate that is too slow can result
in lengthy, inefficient cuts and in some cases,
tooth dulling and overheating. The chips produced
by the cut will generally be thin or powdery.
Cutting with a feed rate that is too fast may cause
the blade to wander, resulting in cuts that are
not straight, and will generate excess heat and
dull the blade. When cutting small or thin-walled
workpieces, the edges of the cut may become
rough or torn.
The best method for evaluating the feed rate is
through trial and error.
Workpiece
Figure 16. Correct TPI.
Damage to the blade, rough cuts, poor cutting
performance, and overheating are all possible
signs of improper blade pitch.
If you feel your machine is not functioning properly
or performing to your standards, check that the
blade pitch is correct for the cut.
-16-
Model G0692 (Mfg. 11/08 and Later)
Blade Break-in
Proper break-in is important for the cutting performance and longevity of the blade. During the
break-in period, only mild pressure should be
exerted on the blade (about half of the normal
feed pressure for a properly broken-in blade).
The duration of the break-in period is determined
by the hardness of the material cut. The breakin period is defined in terms of square inches of
material cut.
Changing Blade
The teeth of saw blades
are sharp and can easily
cut fingers and hands.
Always wear heavy leather gloves when handling
saw blades.
—For hard materials, such as steel, the
break-in period is the first 50 square inches
of material cut.
Tools Needed:
Qty
Phillips Screwdriver #2 ...................................... 1
Hex Wrench 8mm............................................... 1
—For soft materials, such as aluminum,
the break-in period is the first 150 square
inches of material cut.
To replace the blade:
To determine the square inches of a cut, calculate
the area of the cross-section of the workpiece.
Keep in mind when cutting hollow-section pieces
that the area only includes the solid walls of the
workpiece. Refer to Figure 17 to calculate approximate square inches for many typical cuts.
A=LxH
H
L
A = (D⁄2)² x π
D
Th
Th
H
A
D x π x Th
A
2H + 2L x Th
A =Area
H =Height
L =Length
D =Diameter
Th =Material
Thickness
π =3.14
1.DISCONNECT SAW FROM POWER!
2.Loosen the two Phillips head screws shown
in Figure 18.
Note: The upper screw must be loosened
approximately 1⁄4" for Step 3 to work properly.
Phillips Head
Screws
L
Figure 17. Calculating cut area for break-in.
Model G0692 (Mfg. 11/08 and Later)
Figure 18. Guard bracket screw locations.
-17-
3.Retract the blade guard. As it rotates, the
mounting bracket should also rotate, exposing the arbor screw, as shown in Figure 19.
5.
Blade Guard
Remove the arbor screw, arbor washer, arbor
flange, and the old blade (Figure 21).
Blade
Arbor Flange
Arbor Washer
Arbor Screw
Arbor Screw
Mounting Bracket
Figure 19. Blade guard retracted.
4.Lightly press down on the arbor lock button
and rotate the blade until the button moves
inward and locks the arbor. While holding the
button, loosen the arbor screw (Figure 20).
Figure 21. Blade components.
6.
Install the new blade, arbor flange, arbor
washer, and arbor screw in the reverse order
from which they were removed. Use the arbor
lock button to secure the arbor while tightening the arbor screw (Figure 22).
Note: When installing the new blade, make
sure the teeth point downward at the front of
the blade, as shown in Figures 13 & 22
Blade
Arbor Lock Button
Arbor
Flange
Arbor
Washer
Cap
Screw
Arbor Screw
Figure 22. Blade installation sequence.
7.Return the blade guard to its normal position
and tighten both Phillips head screws shown
in Figure 18.
Figure 20. Arbor screw removal.
-18-
Model G0692 (Mfg. 11/08 and Later)
Cutting Procedures
Cutting Tips
After familiarizing yourself with the controls of the
Model G0692, follow the basic outline below to
perform safe and efficient cuts.
•Replace, sharpen, and clean blades as necessary to maintain optimum cutting performance.
To make a cut:
•Use even pressure while cutting. Heavy or
irregular pressure can lead to poor cuts and
damage the blade.
1.
DISCONNECT SAW FROM POWER!
2.Set the vise fence position and angle (Page
13).
3.
Clamp the workpiece in the vise.
4.
Connect the saw to power.
•
Misusing the saw or using incorrect techniques is unsafe and results in poor cuts.
Remember—the blade does the cutting with
the operator's guidance.
•Use a roller stand to support long workpieces.
See Accessories on Page 20.
5.Press the trigger switch to start the blade and
use a controlled, steady force to complete
the cut. When the cut is completed, raise the
saw, release the trigger, and allow the blade
to come to a complete stop before proceeding.
General Machine
Tips
•
When the machine is not in use, raise the
saw to reduce strain on the return spring.
•Inspect the machine regularly to keep it running in top condition.
•
Model G0692 (Mfg. 11/08 and Later)
Clean, lubricate, and cover the machine
before putting it into storage for extended
periods of time.
-19-
ACCESSORIES
SECTION 5: ACCESSORIES
T20920—Replacement blade for G0692 58T
H8724—14" x 1" Carbide Tipped Blade 72T
H5109—14" x 1" Metal Cutting Blade 90T
H5110—14" x 1" Stainless Steel Cutting Blade
90T
Basic Eye Protection
T20501—Face Shield Crown Protector 4"
T20502—Face Shield Crown Protector 7"
T20503—Face Shield Window
T20451—“Kirova” Clear Safety Glasses
T20452—“Kirova” Anti-Reflective S. Glasses
H7194—Bifocal Safety Glasses 1.5
H7195—Bifocal Safety Glasses 2.0
H7196—Bifocal Safety Glasses 2.5
T20502
T20452
T20503
Figure 23. Replacement blade.
G8983—Tilting Roller Stand
Adjusts from 26" to 44", 0º-45º. 150 lb. capacity.
G8984—Single Roller Stand
Adjusts from 265⁄8" to 45". 250 lb. capacity.
G8985—5 Roller Stand
Adjusts from 26" to 445⁄8". 250 lb. capacity.
These super heavy-duty roller stands feature convenient hand knobs for fast height adjustment.
H7194
T20451
Figure 25. Our most popular eye protection.
G7313—700 lb Capacity SHOP FOX® Stand
A perfect stand for mounting your smaller machines
on. Sturdy and rugged for everyday shop use.
G8983
G8985
G8984
Figure 24. SHOP FOX® Roller Stands.
-20-
Figure 26. G7313 SHOP FOX® Stand.
Model G0692 (Mfg. 11/08 and Later)
G5618—Deburring Tool w/2 Blades
G5619—Extra Aluminum Blades
G5620—Extra Brass and Cast Iron Blade
The quickest tool for smoothing freshly machined
metal edges. Comes with two blades, one for steel
and aluminum and one for brass and cast iron.
H8003—Hydraulic Lifting Table - 450 lbs.
This rugged and affordable lifting table allows you
to lift stacks of sheet goods right up to the saw
with minimal effort. Features 393 ⁄ 8" x 193 ⁄4" table,
391⁄ 2" maximum table height, 8" fixed and swivel
casters with brakes.
Figure 27. G5618 Deburring tool.
Figure 29. Model H8003 Hydraulic Lifting Table.
H3153—Pigskin Palm Gloves
H3154—Lined Pigskin Palm Gloves
Durable pigskin leather is combined with cloth
backs for true comfort. One size fits many.
G5562—SLIPIT® 1 Qt. Gel
G5563—SLIPIT® 12 oz Spray
G2871—Boeshield® T-9 12 oz Spray
G2870—Boeshield ® T-9 4 oz Spray
H3788—G96 ® Gun Treatment 12 oz Spray
H3789—G96 ® Gun Treatment 4.5 oz Spray
H3154
H3153
Figure 28. Work gloves.
Figure 30. Recommended products for protecting unpainted cast iron/steel part on machinery.
Model G0692 (Mfg. 11/08 and Later)
-21-
SECTION 6: MAINTENANCE
Cleaning
Always disconnect power
to the machine before
performing maintenance.
Failure to do this may
result in serious personal injury.
Schedule
For optimum performance from your machine,
follow this maintenance schedule and refer to any
specific instructions given in this section.
Daily Check:
•Loose mounting bolts/screws/nuts.
•
Damaged or worn saw blade.
•
Proper function of blade guard.
•
Any other unsafe condition.
•General cleanup to prevent buildup of metal
shavings.
Weekly Maintenance:
•
Clean the machine thoroughly.
•
Clean/grease the vise leadscrew.
Monthly Check:
•
Check/tighten all machine bolts.
Cleaning the Model G0692 is relatively easy.
Vacuum excess metal chips and wipe off the
remaining debris and residue with a dry cloth.
Unpainted Cast Iron
Keep unpainted cast iron surfaces rust-free with
regular applications of products like G96® Gun
Treatment, SLIPIT®, or Boeshield ® T-9, all available through the Grizzly catalog or website.
Lubrication
Vise Leadscrew
1.DISCONNECT SAW FROM POWER!
2.Use a rag to clean any debris from the vise
leadscrew.
3.Apply multipurpose grease to the leadscrew
and completely open and close the vise several times to distribute the grease.
Note: Periodically clean the leadscrew thoroughly with mineral spirits or other degreaser
and relubricate with multipurpose grease.
-22-
Model G0692 (Mfg. 11/08 and Later)
SECTION 7: SERVICE
Review the troubleshooting and procedures in this section to fix or adjust your machine if a problem develops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical
Support at (570) 546-9663.
Troubleshooting
Motor & Electrical
Symptom
Possible Cause
Machine
does 1.Plug/receptacle is at fault or wired incorrectly.
not start/indicator 2. Wall fuse/circuit breaker is blown/tripped.
light does not
come on or a
3.Power supply switched OFF or is at fault.
breaker trips.
4. Wiring is open/has high resistance.
5. Motor ON/OFF switch is at fault.
6. Motor is at fault.
Corrective Action
1.Test for good contacts; correct the wiring.
2.Ensure circuit size is suitable for this machine;
replace weak breaker.
3.Ensure power supply is switched ON; ensure power
supply has the correct voltage.
4. Check for broken wires or disconnected/corroded
connections, and repair/replace as necessary.
5.Replace faulty ON/OFF switch.
6.Test/repair/replace.
Machine stalls or 1. Motor connection is wired incorrectly.
is overloaded.
2.Plug/receptacle is at fault.
3. Motor is at fault.
1. Correct motor wiring connections (Page 27).
2.Test for good contacts; correct the wiring.
3.Test/repair/replace.
Machine
has 1.
vibration or noisy
operation.
2.
3.
4
1.Inspect/replace stripped or damaged bolts/nuts, and
re-tighten with thread locking fluid.
2.Tighten/replace.
3.Relocate/shim machine.
4.Replace dented fan cover; replace loose/damaged
fan.
5.Test by rotating shaft; rotational grinding/loose shaft
requires bearing replacement.
Motor or component is loose.
Motor mount loose/broken.
Machine sits unevenly.
Motor fan is rubbing on fan cover.
5. Motor bearings are at fault.
Indicator light is 1.Plug connecting trigger switch to control box is 1. Correctly insert plug.
on and trigger
unplugged.
switch fails to 2.Trigger switch at fault.
2.Test/repair/replace.
activate motor.
3. Motor is at fault.
3.Test/repair/replace.
Model G0692 (Mfg. 11/08 and Later)
-23-
Blade Troubleshooting
Symptom
Possible Cause
Corrective Action
Blade teeth dull
prematurely.
1. Feed speed/pressure too low.
2.Blade pitch too fine for cut.
3.Impurities in workpiece.
4.Blade not broken-in properly.
1.Increase feed speed/pressure.
2. Check blade pitch, use a coarser-pitch blade.
3.Inspect/clean/discard workpiece.
4.Replace blade and follow Blade Break-in on Page
17.
Blade teeth are broken/
missing.
1. Feed speed/pressure too high.
-24-
1.Reduce feed pressure by relieving pressure on the
feed lever during operation.
2.Allow blade to enter workpiece in a slow and controlled
2.Blade allowed to hop during cut.
manner, follow through with a smooth and even
pressure.
3.Blade was in contact with the 3.Never start the blade in contact with the workpiece.
workpiece when machine was
turned ON.
4. Check blade tooth pitch.
4.Blade tooth pitch incorrect for cut.
5.Replace blade and follow Blade Break-in on Page
5.Blade not broken-in correctly.
17.
Model G0692 (Mfg. 11/08 and Later)
Motor Brushes
During the life of your machine, you may find it
necessary to replace the motor brushes. If the
motor loses power or becomes noisy, check the
brushes and replace them if they are worn down
to 1⁄4" or less.
Tools Needed
Qty
Phillips Screwdriver #2 ...................................... 1
Acetone and Cotton Rag.................................... 1
Crocus Cloth (From Local Auto Parts Store)...... 1
Brush Set............................................................ 1
To replace the brushes:
1.DISCONNECT SAW FROM POWER!
2.Remove the two motor cover screws and the
motor cover (Figure 31).
4.Inspect the commutator surface (Figure 33).
—If the brushes have worn deep grooves in
the commutator, we recommend replacing
the motor. Typically the labor involved with
re-turning the commutator on a lathe and
then undercutting the insulator segments
exceeds the price of a new motor.
—If the commutator only has minor wear and
black-colored carbon tracking (Figure 33),
use a fine crocus cloth to polish the commutator where the brushes ride.
Finish the cleaning process by using acetone and a cotton rag to wipe off any oils
or contaminants from the commutator. DO
NOT use emery cloth or sandpaper to clean
the commutator or you will make it out-ofround, which will cause the new brushes to
arc, overheat, and wear out quickly.
Commutator
Motor
Cover
Figure 31. Motor cover.
Figure 33. Commutator.
3.Pull back the brush springs and remove both
brush assemblies (Figure 32).
5.Replace both brush assemblies, making sure
they are held in place with the spring and that
the wire is connected.
6.Reinstall the motor cover.
Brush
Spring
Brush
Assemblies
Figure 32. Brush removal.
Model G0692 (Mfg. 11/08 and Later)
-25-
SECTION 8: WIRING
These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Study this section carefully. If there are differences between
your machine and what is shown in this section, call Technical Support at (570) 546-9663 for assistance
BEFORE making any changes to the wiring on your machine.
Wiring Safety Instructions
1.
2.
3.
4.
SHOCK HAZARD. Working on wiring that
is connected to a power source is extremely
dangerous. Touching electrified parts will
result in personal injury including but not limited to severe burns, electrocution, or death.
Disconnect the power from the machine
before servicing electrical components!
QUALIFIED ELECTRICIAN. Due to the
inherent hazards of electricity, only a qualified electrician should perform wiring tasks
on this machine. If you are not a qualified electrician, get help from one before
attempting any kind of wiring job.
WIRE CONNECTIONS. All connections
must be tight to prevent wires from loosening during machine operation. Double-check
all wires disconnected or connected during
any wiring task to ensure tight connections.
WIRE/COMPONENT DAMAGE. Damaged
wires or components increase the risk of
serious personal injury, fire, or machine
damage. If you notice that any wires or
components are damaged while performing
a wiring task, replace those wires or components before completing the task.
5.
MODIFICATIONS. Using aftermarket parts or
modifying the wiring beyond what is shown
in the diagram may lead to unpredictable
results, including serious injury or fire.
6.
MOTOR WIRING. The motor wiring shown
in these diagrams is current at the time of
printing, but it may not match your machine.
Always use the wiring diagram inside the
motor junction box.
7.
CAPACITORS. Some capacitors store an
electrical charge for up to five minutes after
being disconnected from the power source.
To avoid being shocked, wait at least this
long before working on capacitors.
8.
CIRCUIT REQUIREMENTS. You MUST follow the requirements on Page 9 when connecting your machine to a power source.
9.
EXPERIENCING DIFFICULTIES. If you are
experiencing difficulties understanding the
information included in this section, contact
our Technical Support at (570) 546-9663.
The photos and diagrams
included in this section are
best viewed in color. You
can view these pages in
color at www.grizzly.com.
-26-
Model G0692 (Mfg. 11/08 and Later)
Wiring Diagram Wiring
View this page in color at
www.grizzly.com.
TRIGGER SWITCH
4
3
2
1
MOTOR 110V
Neutral
Hot
110 VAC
NEMA 1-15 Plug
Figure 34. Wiring.
G0692 14" Dry Cut Metal Saw
READ ELECTRICAL SAFETY
ON PAGE 26!
-27-
SECTION 9: PARTS
Parts Breakdown
14
13
11
21
24
23
12
20
22
19
15
68
16
67
17
18
24
23
44
23 49
66
45
65
23
24
69
39 6
10
48
9 8
7
51
38
42
41
40
46
29
50
29
26
28 27 34
25
83
33 32 31
82
24 43
37
76 75 81
80
103
105
104
102
101
100
47
35
98
97
96
89
18 19
56
2
71
73
74
77
79
99
94
55
57
30
36
78
54
52 53
60
65 18
19 55
61 62
70
72
84
70
58
59
63 64
85
93
92
91
90
84
86
110
65
87
95
88
Blade Not Included
3
4
5
1
23
108
106
4
3
-28-
109
107
Model G0692 (Mfg. 11/08 and Later)
Parts List
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
P0692001
P0692002
PSB40M
PLW04M
P0692005
P0692006
P6202LLB
P0692008
P6000LLB
P0692010
P0692011
P0692012
PW05M
PHTEK31M
P0692015
PTLW02M
PHTEK43M
PW02M
PLW01M
P0692020
P0692021
P0692022
PW05M
PHTEK6M
P0692025
PK19M
P0692027
PEC03M
P6000LLB
P0692030
P6205LLB
P0692032
PK14M
PEC03M
P6200LLB
P0692036
P0692037
PW05M
PHTEK28M
P0692040
PW05M
PHTEK39M
P0692043
P0692044
PHTEK42M
P0692046
P0692047
P0692048
P0692049
P6000LLB
P0692051
P0692052
P0692053
P0692054
PSB137M
BASE
ANCHOR HOUSING
CAP SCREW M8-1.25 X 35
LOCK WASHER 8MM
VISE SLIDE PLATE
MOTOR TILT BASE
BALL BEARING 6202LLB
ROTOR
BALL BEARING 6000LLB
AIR FLOW COVER
MOTOR FRAME
BRUSH HOLDER
FLAT WASHER 4MM
TAP SCREW M4 X 14
STATOR
EXT TOOTH WASHER 5MM
TAP SCREW M5 X 70
FLAT WASHER 5MM
LOCK WASHER 5MM
CAP SCREW M5-.8 X 28
CARBON BRUSH SET
COVER
FLAT WASHER 4MM
TAP SCREW M4 X 16
GEAR SHAFT
KEY 5 X 5 X 14
PINION M1.25 X 43T
E-CLIP 10MM
BALL BEARING 6000LLB
ARBOR
BALL BEARING 6205LLB
GEAR M1.5 X 40T
KEY 5 X 5 X 18
E-CLIP 25MM
BALL BEARING 6200LLB
GEAR BOX
LOWER SWITCH HANDLE
FLAT WASHER 4MM
TAP SCREW M4 X 25
TRIGGER SWITCH
FLAT WASHER 4MM
TAP SCREW M4 X 12
WIRE RETAINER
UPPER SWITCH HANDLE
TAP SCREW M4 X 35
WIRE GUARD
POWER CORD 110V 8'
RIGHT SIDE HANDLE
LEFT SIDE HANDLE
BALL BEARING 6000LLB
GUARD TUBE
FRONT SHAFT BRAKE LEVER
COMPRESSION SPRING
SAWBLADE GUARD
CAP SCREW M5-.8 X 55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
P0692056
P6000LLB
PW03M
PLW03M
PSB02M
P0692061
PSB26M
P0692063
P6000LLB
PSB33M
P0692066
P0692067
P0692068
P0692069
PW01M
P0692071
PB84M
P0692073
P0692074
P0692075
PR04M
P0692077
PSB04M
P0692079
P0692080
P0692081
PN03M
PB126M
P0692084
T20920
P0692086
PB56M
P0692088
P0692089
P0692090
P0692091
P0692092
P0692093
PSB26M
P0692095
P0692096
P0692097
P0692098
PFH02M
P0692100
P0692101
P0692102
P0692103
PN02M
PW04M
P0692106
PSB23M
PLW02M
P0692109
PW02M
BEARING BUSHING
BALL BEARING 6000LLB
FLAT WASHER 6MM
LOCK WASHER 6MM
CAP SCREW M6-1 X 20
RUBBER SEAT
CAP SCREW M6-1 X 12
CENTER COVER
BALL BEARING 6000LLB
CAP SCREW M5-.8 X 12
SLIDING GUARD ASSEMBLY
CONNECTION ROD ASSEMBLY
SPECIAL CAP SCREW M5-.8 X 12
GUARD BUSHING
FLAT WASHER 8MM
CONNECTION ROD BUSHING
HEX BOLT M8-1.25 X 14
LOCK LEVER
RUBBER RING
KNOB HANDLE
EXT RETAINING RING 6MM
SHAFT
CAP SCREW M6-1 X 10
SPRING SEAT SHAFT
SPRING RUBBER SEAT
COMPRESSION SPRING
HEX NUT M8-1.25
HEX BOLT M8-1.25 X 40
ARBOR FLANGE
BLADE 58-T 350 X 2.4 X 25.4MM
CLAMP WASHER
CAP SCREW M10-1.5 X 20
PIVOT SHAFT
FIXED VISE JAW
ANGLE SCALE
DISC SPRING
BUSHING
PULL BAR
CAP SCREW M6-1 X 12
T-NUT M8-1.25
SPACER RING
STUD
LEVER
FLAT HD SCR M6-1 X 12
SADDLE
COMPRESSION SPRING
STEEL BALL
LEADSCREW ASSEMBLY
HEX NUT M10-1.5
FLAT WASHER 10MM
SLAG TRAY SLIDE
CAP SCREW M4-.7 X 12
LOCK WASHER 4MM
SLAG TRAY
FLAT WASHER 5MM
Model G0692 (Mfg. 11/08 and Later)
-29-
Warning Labels
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
200
201
202
203
PLABEL-14B
P0692201
P0692202
P0692203
ELECTRICTY LABEL
READ MANUAL LABEL
WEAR SAFETY GLASSES LABEL
AMPUTATION WARNING LABEL
204
205
206
P0692204
P0692205
P0692206
HEARING WARNINING LABEL
DISCONNECT POWER LABEL
MACHINE ID LABEL
Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine
MUST maintain the original location and readability of the labels on the machine. If any label is
removed or becomes unreadable, REPLACE that label before using the machine again. Contact
Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.
-30-
Model G0692 (Mfg. 11/08 and Later)
WARRANTY CARD
Name _____________________________________________________________________________
Street _____________________________________________________________________________
City _______________________ State _________________________ Zip _____________________
Phone # ____________________ Email _________________________________________________
Model # ____________________ Order # _______________________ Serial # __________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop
better products and services. Of course, all information is strictly confidential.
1.
CUT ALONG DOTTED LINE
2.
How did you learn about us?
____ Advertisement
____ Card Deck
4.
5.
6.
____ Catalog
____ Other:
Which of the following magazines do you subscribe to?
____
____
____
____
____
____
____
____
____
____
3.
____ Friend
____ Website
Cabinetmaker & FDM
Family Handyman
Hand Loader
Handy
Home Shop Machinist
Journal of Light Cont.
Live Steam
Model Airplane News
Old House Journal
Popular Mechanics
____
____
____
____
____
____
____
____
____
____
Popular Science
Popular Woodworking
Precision Shooter
Projects in Metal
RC Modeler
Rifle
Shop Notes
Shotgun News
Today’s Homeowner
Wood
____
____
____
____
____
____
____
Wooden Boat
Woodshop News
Woodsmith
Woodwork
Woodworker West
Woodworker’s Journal
Other:
What is your annual household income?
____ $20,000-$29,000
____ $30,000-$39,000
____ $50,000-$59,000
____ $60,000-$69,000
____ $40,000-$49,000
____ $70,000+
What is your age group?
____ 20-29
____ 50-59
____ 40-49
____ 70+
____ 30-39
____ 60-69
How long have you been a woodworker/metalworker?
____ 0-2 Years
____ 2-8 Years
____ 8-20 Years
____ 20+ Years
How many of your machines or tools are Grizzly?
____ 0-2
____ 3-5
____ 6-9
____ 10+
7.
Do you think your machine represents a good value?
_____ Yes
_____No
8.
Would you recommend Grizzly Industrial to a friend?
_____ Yes
_____No
9.
Would you allow us to use your name as a reference for Grizzly customers in your area?
Note: We never use names more than 3 times.
_____ Yes
_____No
10. Comments: _____________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
WARRANTY AND RETURNS
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the
carton. We will not accept any item back without this number. Proof of purchase must accompany the
merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement