Grizzly G0814X Jointer W/Stand & V-Helical Cutterhead Owner Manual

Grizzly G0814X Jointer W/Stand & V-Helical Cutterhead Owner Manual
MODEL G0813/G0814/G0814X
6" JOINTER
OWNER'S MANUAL
(For models manufactured since 10/19)
COPYRIGHT © MARCH, 2016 BY GRIZZLY INDUSTRIAL, INC. REVISED NOVEMBER, 2019 (MN)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL18046 PRINTED IN TAIWAN
V2.11.19
This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and comprehension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
•
•
•
Lead from lead-based paints.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.
Table of Contents
INTRODUCTION................................................ 2
Contact Info.................................................... 2
Machine Differences....................................... 2
Manual Accuracy............................................ 2
Identification.................................................... 3
Controls & Components.................................. 4
G0813 Machine Data Sheet........................... 6
G0814 Machine Data Sheet........................... 8
G0814X Machine Data Sheet....................... 10
SECTION 1: SAFETY...................................... 12
Safety Instructions for Machinery................. 12
Additional Safety for Jointers........................ 14
SECTION 2: POWER SUPPLY....................... 15
Voltage Conversion to 220V......................... 17
SECTION 3: SETUP........................................ 18
Needed for Setup.......................................... 18
Unpacking..................................................... 18
G0813 Inventory........................................... 19
G0814/G0814X Inventory............................. 20
Hardware Recognition Chart........................ 21
Cleanup......................................................... 22
Site Considerations....................................... 23
Assembly...................................................... 24
Dust Collection.............................................. 31
Test Run....................................................... 31
Recommended Adjustments......................... 32
SECTION 4: OPERATIONS............................ 33
Operation Overview...................................... 33
Stock Inspection & Requirements................ 34
Setting Depth of Cut..................................... 35
Squaring Stock............................................. 36
Surface Planing............................................ 37
Edge Jointing................................................ 38
Bevel Cutting................................................ 39
Rabbet Cutting.............................................. 40
SECTION 5: ACCESSORIES.......................... 42
SECTION 6: MAINTENANCE.......................... 44
Schedule....................................................... 44
Cleaning & Protecting................................... 44
Lubrication.................................................... 45
SECTION 7: SERVICE.................................... 46
Troubleshooting............................................ 46
Setting/Replacing Knives (G0813/G0814)...... 48
Rotating/Replacing Helical Cutterhead
Inserts (G0814X).......................................... 50
Setting Outfeed Table Height....................... 51
Calibrating Depth Scale................................ 52
Adjusting Gibs............................................... 53
Setting Fence Stops..................................... 54
Tensioning/Replacing V-Belt........................ 55
Aligning Pulleys............................................ 56
Checking/Adjusting Table Parallelism.......... 57
SECTION 8: WIRING....................................... 58
Wiring Safety Instructions............................. 58
110V Wiring Diagram.................................... 59
220V Wiring Diagram.................................... 60
SECTION 9: PARTS........................................ 61
Table............................................................. 61
Fence............................................................ 63
Cutterhead ................................................... 64
G0813 Stand................................................. 65
G0814/G0814X Stand.................................. 67
G0813 Labels & Cosmetics.......................... 69
G0814/G0814X Labels & Cosmetics............ 70
WARRANTY & RETURNS.............................. 71
INTRODUCTION
Contact Info
Manual Accuracy
We stand behind our machines! If you have questions or need help, contact us with the information
below. Before contacting, make sure you get the
serial number and manufacture date from the
machine ID label. This will help us help you faster.
We are proud to provide a high-quality owner’s
manual with your new machine!
Grizzly Technical Support
1815 W. Battlefield
Springfield, MO 65807
Phone: (570) 546-9663
Email: techsupport@grizzly.com
We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.
Grizzly Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Email: manuals@grizzly.com
Machine Differences
We made every effort to be exact with the instructions, specifications, drawings, and photographs
in this manual. Sometimes we make mistakes, but
our policy of continuous improvement also means
that sometimes the machine you receive is
slightly different than shown in the manual.
If you find this to be the case, and the difference
between the manual and machine leaves you
confused or unsure about something, check our
website for an updated version. We post current
manuals and manual updates for free on our website at www.grizzly.com.
Alternatively, you can call our Technical Support
for help. Before calling, make sure you write down
the Manufacture Date and Serial Number from
the machine ID label (see below). This information
is required for us to provide proper tech support,
and it helps us determine if updated documentation is available for your machine.
Models G0813, G0814, and G0814X are 1 HP, 6"
jointers with the following differences:
•
•
•
-2-
Model G0813 has a 3-knife cutterhead and a
knock-down stand that requires assembly.
Model G0814 has a 3-knife cutterhead and a
one-piece cabinet stand.
Manufacture Date
Serial Number
Model G0814X has a V-helical cutterhead
with 4 rows and 26 indexable carbide inserts.
It comes with the same one-piece cabinet
stand included with the G0814.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
Identification
Become familiar with the names and locations of the controls and features shown below to better understand
the instructions in this manual.
A
B
C
D
E
F
O
H
N
I
M
J
G
K
L
A.
B.
C.
D.
E.
F.
G.
H.
Outfeed Table
Fence
Cutterhead Guard
Fence Lock
Fence Tilt Handle
Infeed Table
Infeed Table Lever
Fence Tilt Lock
I.
J.
K.
L.
M.
N.
O.
Depth Scale
Infeed Table Lock
ON/OFF Paddle Switch w/Disabling Key
Foot Pedal Caster Assembly
Dust Port
Outfeed Table Lock
Outfeed Table Handwheel
For Your Own Safety Read Instruction Manual Before Operating Jointer
a) Wear eye protection.
b) Always keep cutterhead and drive guards in place and in proper operating condition. ALWAYS
replace cutterhead guard after rabbeting operations.
c) Never make jointing or rabbeting cuts deeper than 1⁄8" or planing cuts deeper than 1⁄16".
d) Always use hold-down or push blocks when jointing material narrower than 3" or surface
planing material thinner than 3".
e) Never perform jointing, planing, or rabbeting cuts on pieces shorter than 8" in length.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
-3-
Controls &
Components
To reduce your risk of
serious injury, read this
entire manual BEFORE
using machine.
C
B
D
G
J
Refer to Figures 1–4 and the following descriptions to become familiar with the basic controls
and components of this machine. Understanding
these items and how they work will help you
understand the rest of the manual and stay safe
when operating this machine.
E
Figure 2. Main table controls, fence, and foot
pedal caster.
B. Fence: Guides workpiece as it moves across
cutterhead; determines angle of cut.
C. Fence Tilt Handle: Tilts fence throughout its
range of motion from 45° inward to 45° outward (135°).
A
Figure 1. ON/OFF paddle switch location.
A. ON/OFF Paddle Switch w/Disabling Key:
Turns motor ON and OFF. Remove yellow
key to disable switch.
-4-
D. Infeed Table: Supports workpiece before it
reaches cutterhead. Position of infeed table
relative to cutterhead determines depth of
cut.
E.
Infeed Table Adjustment Lever: Adjusts
position of infeed table (when infeed table
lock is loosened).
J.
Infeed Table Lock: Loosens to allow adjustment of infeed table height or cutting depth
tightens to secure infeed table.
G. Outfeed Table: Supports workpiece after
it passes over cutterhead. For safety and
best results, outfeed table must be properly
adjusted relative to cutterhead knives/inserts
before ANY operations (refer to Page 51 for
more details).
Model G0813/G0814/G0814X (Mfd. Since 10/19)
H
N
O
M
L
I
F
K
P
Figure 3. Cutterhead guard and depth-of-cut
scale.
H. Cutterhead Guard: Covers cutterhead
until pushed out of the way by workpiece
during operation. When workpiece leaves
cutterhead, guard springs back to its starting
position.
I.
F.
Depth-of-Cut Scale: Indicates cutting depth
of a single pass.
Outfeed Table Handwheel: Adjusts position
of outfeed table. Typically only used when setting outfeed table even with cutterhead knives/
inserts or when servicing the cutterhead.
Figure 4. Fence controls.
L.
Fence Lock: Loosens to allow adjustment of
fence position along width of tables. Tightens
to secure fence.
M. Swing Stop: When engaged, stops fence
at 90°. When disengaged, allows fence to
adjust for bevel cuts.
N. 90° Fence Stop: When engaged, stops
fence at 90°.
Note: Even when fence stop bolt contacts
swing stop, tilt lock must be tightened before
starting machine.
K. Outfeed Table Lock: Loosens to allow
adjustment of outfeed table height; tightens
to secure outfeed table.
Note: Swing stop must be disengaged for
bevel cuts greater than 90°.
O. 45° Fence Stop: Stops fence at 45° outward
(135°).
Note: Even when fence is resting against
stops, tilt lock must be tightened before starting machine.
P.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
Fence Tilt Lock: Secures fence tilt setting at
desired angle.
-5-
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
MODEL G0813 6" X 48" JOINTER WITH ECONOMY STAND
Product Dimensions:
Weight.............................................................................................................................................................. 247 lbs.
Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 47-1/2 x 20 x 42 in.
Footprint (Length x Width)..................................................................................................................... 14-1/4 x 27 in.
Shipping Dimensions:
Carton #1
Type........................................................................................................................................... Cardboard Box
Content................................................................................................................................................. Machine
Weight.................................................................................................................................................... 239 lbs.
Length x Width x Height............................................................................................................. 49 x 22 x 13 in.
Must Ship Upright......................................................................................................................................... Yes
Carton #2
Type........................................................................................................................................... Cardboard Box
Content...................................................................................................................................................... Stand
Weight...................................................................................................................................................... 13 lbs.
Length x Width x Height............................................................................................................... 16 x 19 x 6 in.
Must Ship Upright.......................................................................................................................................... No
Electrical:
Power Requirement............................................................................................. 110V or 220V, Single-Phase, 60 Hz
Prewired Voltage.................................................................................................................................................. 110V
Full-Load Current Rating....................................................................................................... 14A at 110V, 7A at 220V
Minimum Circuit Size.......................................................................................................... 20A at 110V, 15A at 220V
Connection Type....................................................................................................................................... Cord & Plug
Power Cord Included.............................................................................................................................................. Yes
Power Cord Length................................................................................................................................................. 6 ft.
Power Cord Gauge......................................................................................................................................... 16 AWG
Plug Included.......................................................................................................................................................... Yes
Included Plug Type................................................................................................................................. 5-15 for 110V
Recommended Plug Type...................................................................................................................... 6-15 for 220V
Switch Type.................................................................................................. Paddle Safety Switch w/Removable Key
Motors:
Main
Horsepower................................................................................................................................................ 1 HP
Phase............................................................................................................................................ Single-Phase
Amps....................................................................................................................................................... 14A/7A
Speed................................................................................................................................................ 3450 RPM
Type................................................................................................................. TEFC Capacitor-Start Induction
Power Transfer .................................................................................................................................. Belt Drive
Bearings........................................................................................................ Sealed & Permanently Lubricated
Centrifugal Switch/Contacts Type......................................................................................................... External
Model G0813
-6-
The information contained herein is deemed accurate as of 11/26/2019 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 1 OF 3
Model G0813/G0814/G0814X (Mfd. Since 10/19)
Main Specifications:
Main Specifications
Jointer Size.................................................................................................................................................. 6 in.
Bevel Jointing............................................................................................................................. 0 – 45 deg. L/R
Maximum Width of Cut................................................................................................................................ 6 in.
Maximum Depth of Cut............................................................................................................................. 1/8 in.
Minimum Workpiece Length........................................................................................................................ 8 in.
Minimum Workpiece Width....................................................................................................................... 3/4 in.
Minimum Workpiece Thickness................................................................................................................ 1/2 in.
Maximum Rabbeting Depth...................................................................................................................... 1/2 in.
Number of Cuts Per Minute..................................................................................................................... 15,000
Fence Information
Fence Length....................................................................................................................................... 29-1/8 in.
Fence Width.......................................................................................................................................... 1-1/4 in.
Fence Height............................................................................................................................................... 4 in.
Fence Stops............................................................................................................................. 45, 90, 135 deg.
Cutterhead Information
Cutterhead Type........................................................................................................................... Straight Knife
Cutterhead Diameter............................................................................................................................. 2-1/2 in.
Cutterhead Speed............................................................................................................................. 5000 RPM
Knife Information
Number of Knives............................................................................................................................................. 3
Knife Length................................................................................................................................................. 6 in.
Knife Width.................................................................................................................................................. 1 in.
Knife Thickness........................................................................................................................................ 1/8 in.
Knife Adjustment............................................................................................................................ Jack Screws
Table Information
Table Length........................................................................................................................................ 47-3/8 in.
Table Width........................................................................................................................................... 6-5/8 in.
Table Thickness.................................................................................................................................... 1-1/4 in.
Floor to Table Height........................................................................................................................... 33-5/8 in.
Table Adjustment Type........................................................................................................... Handwheel/Lever
Table Movement Type............................................................................................................. Dovetailed Ways
Construction
Base........................................................................................................................................................... Steel
Body Assembly.................................................................................................................................... Cast Iron
Fence Assembly.................................................................................................................................. Cast Iron
Guard.......................................................................................................................................... Die Cast Metal
Table....................................................................................................................... Precision-Ground Cast Iron
Paint Type/Finish....................................................................................................................... Powder Coated
Other Information
Number of Dust Ports....................................................................................................................................... 1
Dust Port Size.............................................................................................................................................. 4 in.
Mobile Base............................................................................................................................................. Built-In
Other Specifications:
Country of Origin .............................................................................................................................................. Taiwan
Warranty ........................................................................................................................................................... 1 Year
Approximate Assembly & Setup Time .............................................................................................................. 1 Hour
Serial Number Location .................................................................................................................................. ID Label
Model G0813
The information contained herein is deemed accurate as of 11/26/2019 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
PAGE 2 OF 3
-7-
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
MODEL G0814 6" X 48" JOINTER WITH CABINET STAND
Product Dimensions:
Weight.............................................................................................................................................................. 245 lbs.
Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 47-1/2 x 20 x 42 in.
Footprint (Length x Width)..................................................................................................................... 13-1/2 x 18 in.
Shipping Dimensions:
Carton #1
Type........................................................................................................................................... Cardboard Box
Content................................................................................................................................................. Machine
Weight.................................................................................................................................................... 183 lbs.
Length x Width x Height............................................................................................................. 49 x 22 x 13 in.
Must Ship Upright......................................................................................................................................... Yes
Carton #2
Type........................................................................................................................................... Cardboard Box
Content...................................................................................................................................................... Stand
Weight...................................................................................................................................................... 77 lbs.
Length x Width x Height............................................................................................................. 21 x 17 x 30 in.
Must Ship Upright.......................................................................................................................................... No
Electrical:
Power Requirement............................................................................................. 110V or 220V, Single-Phase, 60 Hz
Prewired Voltage.................................................................................................................................................. 110V
Full-Load Current Rating....................................................................................................... 14A at 110V, 7A at 220V
Minimum Circuit Size.......................................................................................................... 20A at 110V, 15A at 220V
Connection Type....................................................................................................................................... Cord & Plug
Power Cord Included.............................................................................................................................................. Yes
Power Cord Length................................................................................................................................................. 6 ft.
Power Cord Gauge......................................................................................................................................... 16 AWG
Plug Included.......................................................................................................................................................... Yes
Included Plug Type................................................................................................................................. 5-15 for 110V
Recommended Plug Type...................................................................................................................... 6-15 for 220V
Switch Type.................................................................................................. Paddle Safety Switch w/Removable Key
Motors:
Main
Horsepower................................................................................................................................................ 1 HP
Phase............................................................................................................................................ Single-Phase
Amps....................................................................................................................................................... 14A/7A
Speed................................................................................................................................................ 3450 RPM
Type................................................................................................................. TEFC Capacitor-Start Induction
Power Transfer .................................................................................................................................. Belt Drive
Bearings........................................................................................................ Sealed & Permanently Lubricated
Centrifugal Switch/Contacts Type......................................................................................................... External
Model G0814
-8-
The information contained herein is deemed accurate as of 11/26/2019 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 1 OF 3
Model G0813/G0814/G0814X (Mfd. Since 10/19)
Main Specifications:
Main Specifications
Jointer Size.................................................................................................................................................. 6 in.
Bevel Jointing............................................................................................................................. 0 – 45 deg. L/R
Maximum Width of Cut................................................................................................................................ 6 in.
Maximum Depth of Cut............................................................................................................................. 1/8 in.
Minimum Workpiece Length........................................................................................................................ 8 in.
Minimum Workpiece Width....................................................................................................................... 3/4 in.
Minimum Workpiece Thickness................................................................................................................ 1/2 in.
Maximum Rabbeting Depth...................................................................................................................... 1/2 in.
Number of Cuts Per Minute..................................................................................................................... 15,000
Fence Information
Fence Length....................................................................................................................................... 29-1/8 in.
Fence Width.......................................................................................................................................... 1-1/4 in.
Fence Height............................................................................................................................................... 4 in.
Fence Stops............................................................................................................................. 45, 90, 135 deg.
Cutterhead Information
Cutterhead Type........................................................................................................................... Straight Knife
Cutterhead Diameter............................................................................................................................. 2-1/2 in.
Cutterhead Speed............................................................................................................................. 5000 RPM
Knife Information
Number of Knives............................................................................................................................................. 3
Knife Length................................................................................................................................................. 6 in.
Knife Width.................................................................................................................................................. 1 in.
Knife Thickness........................................................................................................................................ 1/8 in.
Knife Adjustment............................................................................................................................ Jack Screws
Table Information
Table Length........................................................................................................................................ 47-3/8 in.
Table Width........................................................................................................................................... 6-5/8 in.
Table Thickness.................................................................................................................................... 1-1/4 in.
Floor to Table Height........................................................................................................................... 33-5/8 in.
Table Adjustment Type........................................................................................................... Handwheel/Lever
Table Movement Type............................................................................................................. Dovetailed Ways
Construction
Base........................................................................................................................................................... Steel
Body Assembly.................................................................................................................................... Cast Iron
Cabinet....................................................................................................................................................... Steel
Fence Assembly.................................................................................................................................. Cast Iron
Guard.......................................................................................................................................... Die Cast Metal
Table....................................................................................................................... Precision-Ground Cast Iron
Paint Type/Finish....................................................................................................................... Powder Coated
Other Information
Number of Dust Ports....................................................................................................................................... 1
Dust Port Size.............................................................................................................................................. 4 in.
Mobile Base............................................................................................................................................. Built-In
Other Specifications:
Country of Origin .............................................................................................................................................. Taiwan
Warranty ........................................................................................................................................................... 1 Year
Approximate Assembly & Setup Time .............................................................................................................. 1 Hour
Serial Number Location .................................................................................................................................. ID Label
Model G0814
The information contained herein is deemed accurate as of 11/26/2019 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
PAGE 2 OF 3
-9-
G0814X Machine Data Sheet
0$&+,1('$7$
6+((7
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
02'(/*;-2,17(5:67$1' 9+(/,&$/
&877(5+($'
Product Dimensions:
Weight.............................................................................................................................................................. 245 lbs.
Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 47-1/2 x 20 x 42 in.
Footprint (Length x Width)..................................................................................................................... 13-1/2 x 18 in.
Shipping Dimensions:
Carton #1
Type........................................................................................................................................... Cardboard Box
Content................................................................................................................................................. Machine
Weight.................................................................................................................................................... 183 lbs.
Length x Width x Height............................................................................................................. 49 x 22 x 13 in.
Must Ship Upright......................................................................................................................................... Yes
Carton #2
Type........................................................................................................................................... Cardboard Box
Content...................................................................................................................................................... Stand
Weight...................................................................................................................................................... 77 lbs.
Length x Width x Height............................................................................................................. 21 x 17 x 30 in.
Must Ship Upright.......................................................................................................................................... No
Electrical:
Power Requirement............................................................................................. 110V or 220V, Single-Phase, 60 Hz
Prewired Voltage.................................................................................................................................................. 110V
Full-Load Current Rating....................................................................................................... 14A at 110V, 7A at 220V
Minimum Circuit Size.......................................................................................................... 20A at 110V, 15A at 220V
Connection Type....................................................................................................................................... Cord & Plug
Power Cord Included.............................................................................................................................................. Yes
Power Cord Length................................................................................................................................................. 6 ft.
Power Cord Gauge......................................................................................................................................... 16 AWG
Plug Included.......................................................................................................................................................... Yes
Included Plug Type................................................................................................................................. 5-15 for 110V
Recommended Plug Type...................................................................................................................... 6-15 for 220V
Switch Type.................................................................................................. Paddle Safety Switch w/Removable Key
Motors:
Main
Horsepower................................................................................................................................................ 1 HP
Phase............................................................................................................................................ Single-Phase
Amps....................................................................................................................................................... 14A/7A
Speed................................................................................................................................................ 3450 RPM
Type................................................................................................................. TEFC Capacitor-Start Induction
Power Transfer ............................................................................................................................................ Belt
Bearings........................................................................................................ Sealed & Permanently Lubricated
Centrifugal Switch/Contacts Type......................................................................................................... External
Model G0814X
-10-
The information contained herein is deemed accurate as of 10/22/2019 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 1 OF 3
Model G0813/G0814/G0814X (Mfd. Since 10/19)
Main Specifications:
Main Specifications
Jointer Size.................................................................................................................................................. 6 in.
Bevel Jointing............................................................................................................................. 0 - 45 deg. L/R
Maximum Width of Cut................................................................................................................................ 6 in.
Maximum Depth of Cut............................................................................................................................. 1/8 in.
Minimum Workpiece Length........................................................................................................................ 8 in.
Minimum Workpiece Width....................................................................................................................... 3/4 in.
Minimum Workpiece Thickness................................................................................................................ 1/2 in.
Maximum Rabbeting Depth...................................................................................................................... 1/2 in.
Number of Cuts Per Minute..................................................................................................................... 20,000
Fence Information
Fence Length....................................................................................................................................... 29-1/8 in.
Fence Width.......................................................................................................................................... 1-1/4 in.
Fence Height............................................................................................................................................... 4 in.
Fence Stops............................................................................................................................. 45, 90, 135 deg.
Cutterhead Information
Cutterhead Type.................................................................................................................................. V-Helical
Cutterhead Diameter............................................................................................................................. 2-1/2 in.
Number of Cutter Rows.................................................................................................................................... 4
Number of Indexable Cutters.......................................................................................................................... 26
Cutterhead Speed............................................................................................................................. 5000 RPM
Cutter Insert Information
Cutter Insert Type.................................................................................................................. Indexable Carbide
Cutter Insert Length.................................................................................................................................. 15mm
Cutter Insert Width.................................................................................................................................... 15mm
Cutter Insert Thickness............................................................................................................................ 2.5mm
Table Information
Table Length........................................................................................................................................ 47-3/8 in.
Table Width........................................................................................................................................... 6-5/8 in.
Table Thickness.................................................................................................................................... 1-1/4 in.
Floor to Table Height........................................................................................................................... 33-5/8 in.
Table Adjustment Type........................................................................................................... Handwheel/Lever
Table Movement Type............................................................................................................. Dovetailed Ways
Construction
Base........................................................................................................................................................... Steel
Body Assembly.................................................................................................................................... Cast Iron
Cabinet....................................................................................................................................................... Steel
Fence Assembly.................................................................................................................................. Cast Iron
Guard.......................................................................................................................................... Die-Cast Metal
Table....................................................................................................................... Precision-Ground Cast Iron
Paint Type/Finish....................................................................................................................... Powder Coated
Other Information
Number of Dust Ports....................................................................................................................................... 1
Dust Port Size.............................................................................................................................................. 4 in.
Mobile Base............................................................................................................................................. Built-In
Other Specifications:
Country of Origin .............................................................................................................................................. Taiwan
Warranty ........................................................................................................................................................... 1 Year
Approximate Assembly & Setup Time .............................................................................................................. 1 Hour
Serial Number Location .................................................................................................................................. ID Label
Model G0814X
The information contained herein is deemed accurate as of 11/11/2019 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
PAGE 2 OF 3
-11-
SECTION 1: SAFETY
For Your Own Safety, Read Instruction
Manual Before Operating This Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
NOTICE
Alerts the user to useful information about proper operation of the
machine to avoid machine damage.
Safety Instructions for Machinery
OWNER’S MANUAL. Read and understand this
owner’s manual BEFORE using machine.
TRAINED OPERATORS ONLY. Untrained operators have a higher risk of being hurt or killed.
Only allow trained/supervised people to use this
machine. When machine is not being used, disconnect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially
around children. Make your workshop kid proof!
DANGEROUS ENVIRONMENTS. Do not use
machinery in areas that are wet, cluttered, or have
poor lighting. Operating machinery in these areas
greatly increases the risk of accidents and injury.
MENTAL ALERTNESS REQUIRED. Full mental
alertness is required for safe operation of machinery. Never operate under the influence of drugs or
alcohol, when tired, or when distracted.
-12-
ELECTRICAL EQUIPMENT INJURY RISKS.
You can be shocked, burned, or killed by touching
live electrical components or improperly grounded
machinery. To reduce this risk, only allow qualified
service personnel to do electrical installation or
repair work, and always disconnect power before
accessing or exposing electrical equipment.
DISCONNECT POWER FIRST. Always disconnect machine from power supply BEFORE making adjustments, changing tooling, or servicing
machine. This prevents an injury risk from unintended startup or contact with live electrical components.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. Everyday
eyeglasses are NOT approved safety glasses.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
WEARING PROPER APPAREL. Do not wear
clothing, apparel or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to reduce
risk of slipping and losing control or accidentally
contacting cutting tool or moving parts.
HAZARDOUS DUST. Dust created by machinery
operations may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece material. Always wear a NIOSH-approved respirator to
reduce your risk.
HEARING PROTECTION. Always wear hearing protection when operating or observing loud
machinery. Extended exposure to this noise
without hearing protection can cause permanent
hearing loss.
REMOVE ADJUSTING TOOLS. Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys, wrenches,
or any other tools on machine. Always verify
removal before starting!
USE CORRECT TOOL FOR THE JOB. Only use
this tool for its intended purpose—do not force
it or an attachment to do a job for which it was
not designed. Never make unapproved modifications—modifying tool or using it differently than
intended may result in malfunction or mechanical
failure that can lead to personal injury or death!
AWKWARD POSITIONS. Keep proper footing
and balance at all times when operating machine.
Do not overreach! Avoid awkward hand positions
that make workpiece control difficult or increase
the risk of accidental injury.
CHILDREN & BYSTANDERS. Keep children and
bystanders at a safe distance from the work area.
Stop using machine if they become a distraction.
GUARDS & COVERS. Guards and covers reduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged, and working correctly BEFORE
operating machine.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
FORCING MACHINERY. Do not force machine.
It will do the job safer and better at the rate for
which it was designed.
NEVER STAND ON MACHINE. Serious injury
may occur if machine is tipped or if the cutting
tool is unintentionally contacted.
STABLE MACHINE. Unexpected movement during operation greatly increases risk of injury or
loss of control. Before starting, verify machine is
stable and mobile base (if used) is locked.
USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for recommended accessories. Using improper accessories will increase the risk of serious injury.
UNATTENDED OPERATION. To reduce the
risk of accidental injury, turn machine OFF and
ensure all moving parts completely stop before
walking away. Never leave machine running
while unattended.
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to keep
machine in good working condition. A machine
that is improperly maintained could malfunction,
leading to serious personal injury or death.
DAMAGED PARTS. Regularly inspect machine
for damaged, loose, or mis-adjusted parts—or
any condition that could affect safe operation.
Immediately repair/replace BEFORE operating
machine. For your own safety, DO NOT operate
machine with damaged parts!
MAINTAIN POWER CORDS. When disconnecting cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the cord
may damage the wires inside. Do not handle
cord/plug with wet hands. Avoid cord damage by
keeping it away from heated surfaces, high traffic
areas, harsh chemicals, and wet/damp locations.
EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the intended operation, stop using the machine! Contact our
Technical Support at (570) 546-9663.
-13-
Additional Safety for Jointers
Serious cuts, amputation, entanglement, or death can occur from contact with rotating cutterhead
or other moving components! Flying chips from cutting operations can cause eye injuries or
blindness. Workpieces or inserts/knives thrown by cutterhead (kickback) can strike nearby
operator or bystanders with deadly force. To reduce the risk of serious personal injury from these
hazards, operator and bystanders MUST completely heed the hazards and warnings below.
KICKBACK. Occurs when workpiece is ejected
from machine at a high rate of speed. Kickback
injuries occur from getting struck by workpiece or
hands being pulled into cutterhead. To reduce the
risk of kickback, only use proper workpieces, safe
feeding techniques, and proper machine setup or
maintenance.
GUARD REMOVAL. Operating jointer without
guards unnecessarily exposes operator to knives/
inserts and other hazardous moving parts. Except
when rabbeting, never operate jointer or allow it to
be connected to power if any guards are removed.
Turn jointer OFF and disconnect power before
clearing any shavings or sawdust from around cutterhead. After rabbeting or maintenance is complete, immediately replace all guards and ensure
they are properly installed/adjusted before resuming regular operations.
DULL OR DAMAGED KNIVES/INSERTS. Dull or
damaged knives/inserts increase risk of kickback
and cause poor workpiece finish. Only use sharp,
undamaged knives/inserts.
OUTFEED TABLE ALIGNMENT. Setting outfeed
table too high can cause workpiece to hit table or
get stuck while feeding. Setting outfeed table too
low may cause workpiece to rock or shift while
feeding. Both of these results will increase risk
of kickback. Always keep outfeed table even with
knives/inserts at highest point during rotation.
INSPECTING STOCK. Impact injuries or kickback may result from using improper workpieces.
Thoroughly inspect and prepare workpiece before
cutting. Verify workpiece is free of nails, staples,
loose knots or other foreign material. Always joint
warped workpieces with cupped side facing down.
MAXIMUM CUTTING DEPTH. To reduce risk of
kickback, never cut deeper than 1⁄ 8" per pass.
-14-
GRAIN DIRECTION. Jointing against the grain
or end grain can increase risk of kickback. It also
requires more cutting force, which produces chatter or excessive chip out. Always joint or surface
plane WITH the grain.
CUTTING LIMITATIONS. Cutting workpieces that
do not meet minimum dimension requirements can
result in kickback or accidental contact with cutterhead. Never perform jointing, planing, or rabbeting
cuts on pieces smaller than specified in machine
data sheet.
PUSH BLOCKS. Push blocks reduce risk of accidental cutterhead contact with hands. Always use
push blocks when planing materials less than 3"
high or wide. Never pass your hands directly over
cutterhead without a push block.
WORKPIECE SUPPORT. Poor workpiece support or loss of workpiece control while feeding will
increase risk of kickback or accidental contact
with cutterhead. Support workpiece with fence
continuously during operation. Support long stock
with auxiliary tables if necessary.
FEED WORKPIECE PROPERLY. Kickback or
accidental cutterhead contact may result if workpiece is fed into cutterhead the wrong way. Allow
cutterhead to reach full speed before feeding.
Never start jointer with workpiece touching cutterhead. Always feed workpiece from infeed side to
outfeed side without stopping until cut is complete.
Never move workpiece backwards while feeding.
SECURE KNIVES/INSERTS. Loose knives or
improperly set inserts can be thrown from cutterhead with dangerous force. Always verify knives/
inserts are secure and properly adjusted before
operation. Straight knives should never project
more than 1⁄ 8" (0.125") from cutterhead body.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
SECTION 2: POWER SUPPLY
Availability
Circuit Information
Before installing the machine, consider the availability and proximity of the required power supply
circuit. If an existing circuit does not meet the
requirements for this machine, a new circuit must
be installed. To minimize the risk of electrocution,
fire, or equipment damage, installation work and
electrical wiring must be done by an electrician or
qualified service personnel in accordance with all
applicable codes and standards.
A power supply circuit includes all electrical
equipment between the breaker box or fuse panel
in the building and the machine. The power supply circuit used for this machine must be sized to
safely handle the full-load current drawn from the
machine for an extended period of time. (If this
machine is connected to a circuit protected by
fuses, use a time delay fuse marked D.)
Electrocution, fire, shock,
or equipment damage
may occur if machine is
not properly grounded
and connected to power
supply.
Full-Load Current Rating
The full-load current rating is the amperage a
machine draws at 100% of the rated output power.
On machines with multiple motors, this is the
amperage drawn by the largest motor or sum of all
motors and electrical devices that might operate
at one time during normal operations.
Full-Load Current Rating at 110V....... 14 Amps
Full-Load Current Rating at 220V........ 7 Amps
The full-load current is not the maximum amount
of amps that the machine will draw. If the machine
is overloaded, it will draw additional amps beyond
the full-load rating.
If the machine is overloaded for a sufficient length
of time, damage, overheating, or fire may result—
especially if connected to an undersized circuit.
To reduce the risk of these hazards, avoid overloading the machine during operation and make
sure it is connected to a power supply circuit that
meets the specified circuit requirements.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
For your own safety and protection of
property, consult an electrician if you are
unsure about wiring practices or electrical
codes in your area.
Note: Circuit requirements in this manual apply to
a dedicated circuit—where only one machine will
be running on the circuit at a time. If machine will
be connected to a shared circuit where multiple
machines may be running at the same time, consult an electrician or qualified service personnel to
ensure circuit is properly sized for safe operation.
Circuit Requirements for 110V
This machine is prewired to operate on a power
supply circuit that has a verified ground and meets
the following requirements:
Nominal Voltage..................... 110V, 115V, 120V
Cycle...........................................................60 Hz
Phase............................................ Single-Phase
Power Supply Circuit.......................... 20 Amps
Plug/Receptacle.............................. NEMA 5-15
Circuit Requirements for 220V
This machine can be converted to operate on a
power supply circuit that has a verified ground
and meets the requirements listed below. (Refer
to Voltage Conversion instructions for details.)
Nominal Voltage.......... 208V, 220V, 230V, 240V
Cycle...........................................................60 Hz
Phase............................................ Single-Phase
Power Supply Circuit.......................... 15 Amps
Plug/Receptacle.............................. NEMA 6-15
-15-
Grounding Requirements
This machine MUST be grounded. In the event
of certain malfunctions or breakdowns, grounding
reduces the risk of electric shock by providing a
path of least resistance for electric current.
For 110V operation: This machine is equipped
with a power cord that has an equipment-grounding wire and a grounding plug (see following figure). The plug must only be inserted into a matching receptacle (outlet) that is properly installed
and grounded in accordance with all local codes
and ordinances.
GROUNDED
5-15 RECEPTACLE
Grounding Pin
5-15 PLUG
Neutral Hot
Figure 5. Typical 5-15 plug and receptacle.
GROUNDED
6-15 RECEPTACLE
Current Carrying Prongs
6-15 PLUG
Grounding Pin
Figure 6. Typical 6-15 plug and receptacle.
Improper connection of the equipment-grounding
wire can result in a risk of electric shock. The
wire with green insulation (with or without yellow
stripes) is the equipment-grounding wire. If repair
or replacement of the power cord or plug is necessary, do not connect the equipment-grounding
wire to a live (current carrying) terminal.
Check with a qualified electrician or service personnel if you do not understand these grounding
requirements, or if you are in doubt about whether
the tool is properly grounded. If you ever notice
that a cord or plug is damaged or worn, disconnect it from power, and immediately replace it with
a new one.
Extension Cords
We do not recommend using an extension cord
with this machine. If you must use an extension
cord, only use it if absolutely necessary and only
on a temporary basis.
SHOCK HAZARD!
Two-prong outlets do not meet the grounding
requirements for this machine. Do not modify
or use an adapter on the plug provided—if
it will not fit the outlet, have a qualified
electrician install the proper outlet with a
verified ground.
For 220V operation: The plug specified under
“Circuit Requirements for 220V” on the previous
page has a grounding prong that must be attached
to the equipment-grounding wire on the included
power cord. The plug must only be inserted into
a matching receptacle (see following figure) that
is properly installed and grounded in accordance
with all local codes and ordinances.
-16-
Extension cords cause voltage drop, which can
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).
Any extension cord used with this machine must
be in good condition and contain a ground wire
and matching plug/receptacle. Additionally, it must
meet the following size requirements:
Minimum Gauge Size............................14 AWG
Maximum Length (Shorter is Better).......50 ft.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
Voltage Conversion
to 220V
The voltage conversion MUST be performed by
an electrician or qualified service personnel.
The voltage conversion procedure consists of
rewiring the motor and installing the correct plug.
A wiring diagram is provided on Page 60 for your
reference.
4.
Use wire nuts to connect wires as indicated
in Figure 8. Twist wire nuts onto their respective wires and wrap them with electrical tape
so they will not come loose.
Connect Wires
and Secure
with Nuts
To Switch
Ground
IMPORTANT: If the diagram included on the
motor conflicts with the one on Page 60, the motor
may have changed since the manual was printed.
Use the diagram provided on the motor junction
box instead.
Items Needed
Qty
•
Phillips Head Screwdriver #2...................... 1
•
Electrical Tape............................. As Needed
•
Wire Nut (16 AWG x 3)................................ 1
•
6-15 Plug..................................................... 1
•
Wire Cutters/Stripper................................... 1
To convert Model G0813/G0814 to 220V:
1.
DISCONNECT MACHINE FROM POWER!
2.
Cut off existing 5-15 plug.
3.
Open motor junction box, remove two wire
nuts indicated in Figure 7, then disconnect
wires.
Remove
Wire
Nuts and
Disconnect
Wires
Figure 8. Motor rewired to 220V.
5.
Close and secure motor junction box.
6.
Install a 6-15 plug according to manufacturer's instructions. If plug manufacturer's
instructions are not available, NEMA standard 6-15 plug wiring is provided on Page 60.
To Switch
Ground
Figure 7. Inside motor junction box (motor prewired to 120V).
Model G0813/G0814/G0814X (Mfd. Since 10/19)
-17-
SECTION 3: SETUP
Needed for Setup
This machine presents
serious injury hazards
to untrained users. Read
through this entire manual
to become familiar with
the controls and operations before starting the
machine!
Wear safety glasses during
the entire setup process!
HEAVY LIFT!
Straining or crushing injury
may occur from improperly
lifting machine or some of
its parts. To reduce this risk,
get help from other people
and use a forklift (or other
lifting equipment) rated for
weight of this machine.
No list of safety guidelines can be complete. Every shop environment is different.
Always consider safety first, as it applies
to your individual working conditions. Use
this and other machinery with caution and
respect. Failure to do so could result in
serious personal injury, damage to equipment, or poor work results.
The following items are needed, but not included,
for the setup/assembly of this machine.
Description
Qty
•
Safety Glasses (for each person)................ 1
•
Solvent/Cleaner........................................... 1
•
Shop Rags................................................... 1
•
Wrench or Socket 14mm.......................1 Ea.
•
Hex Wrench 2.5mm...............................1 Ea.
•
Straightedge 4'............................................ 1
•
Stubby Phillips Screwdriver #2.................... 1
•
Dust Collection System............................... 1
•
4" Dust Hose (length as needed)................ 1
•
4" Hose Clamp............................................ 1
•
Another Person........................................... 1
Unpacking
This machine was carefully packaged for safe
transport. When unpacking, separate all enclosed
items from packaging materials and inspect them
for shipping damage. If items are damaged,
please call us immediately at (570) 546-9663.
IMPORTANT: Save all packaging materials until
you are completely satisfied with the machine and
have resolved any issues between Grizzly or the
shipping agent. You MUST have the original packaging to file a freight claim. It is also extremely
helpful if you need to return your machine later.
Like all machinery there is potential danger
when operating this machine. Accidents
are frequently caused by lack of familiarity
or failure to pay attention. Use this machine
with respect and caution to decrease the
risk of operator injury. If normal safety precautions are overlooked or ignored, serious personal injury may occur.
-18-
Model G0813/G0814/G0814X (Mfd. Since 10/19)
G0813 Inventory
The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
NOTICE
If you cannot find an item on this list, carefully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpacking or they are pre-installed at the factory.
A
B
D
C
G
E
H
F
I
K
J
L
Figure 9. Component inventory.
M
N
O
P
S
R
Q
Component Inventory (Figures 9–10)
Qty
A. Jointer Assembly w/Carriage Mount............ 1
B. Motor........................................................... 1
C. Fence Assembly & Carriage ...................... 1
D. Cutterhead Guard........................................ 1
E. Belt Guard................................................... 1
F. Knife-Setting Jig.......................................... 1
G. Push Blocks................................................. 2
H. Hex Wrench 3mm..................................1 Ea.
I. Belt.............................................................. 1
J.Fence Lock w/Locking Nut.......................... 1
K. Fence Tilt Handle........................................ 1
L. Open-End Wrenches 8/10, 12/14mm....1 Ea.
M. Front Panel w/Switch................................... 1
N. Right Panel.................................................. 1
O. Left Panel.................................................... 1
P. Rear Panel (w/Switch Box, Cords).............. 1
Q. Corner Supports.......................................... 4
R. Top Plate..................................................... 1
S. Dust Port..................................................... 1
T. Foot Pedal Caster Assembly....................... 1
U. Motor Mount Plate....................................... 1
V. Left Chute Support...................................... 1
W. Right Chute Panel....................................... 1
X. Mobile Base Chassis................................... 1
Fasteners (Not Shown)
•
Flange Screws #10-24 x 3 ⁄ 8" (Stand)......... 54
•
Hex Nuts #10-24 (Stand)............................. 4
•
Carriage Bolts 5 ⁄ 16"-18 x 5 ⁄ 8" (Motor/Stand)... 4
•
Flat Washers 5 ⁄ 16" (Motor/Stand).................. 4
•
Hex Nuts 5 ⁄ 16"-18 (Motor/Stand)................... 4
•
Hex Bolts 3 ⁄ 8"-16 x 1" (Mb. Base/Stand)...... 4
•
Flat Washers 3 ⁄ 8" (Mobile Base/Stand)........ 8
•
Hex Nuts 3 ⁄ 8"-16 (Mobile Base/Stand)......... 4
•
Hex Bolts 3 ⁄ 8"-16 x 21⁄ 2" (Wheel/Stand)........ 2
•
Flat Washers 3 ⁄ 8" (Wheel/Stand)................. 4
•
Hex Nuts 3 ⁄ 8"-16 (Wheel/Stand)................... 2
•
Hex Bolt 5 ⁄ 16"-18 x 2" (Wheel/Stand)............ 1
•
Flat Washer 5 ⁄ 16" (Wheel/Stand).................. 1
•
Hex Bolts 3 ⁄ 8"-16 x 3 ⁄4" (Jointer/Stand).......... 3
•
Flat Washers 3 ⁄ 8" (Jointer/Stand)................. 3
•
Hex Bolt 5 ⁄ 16"-18 x 21⁄ 2" (Belt Guard)............ 1
•
Flat Washer 5 ⁄ 16" (Belt Guard)...................... 1
•
Flange Screws #10-24 x 3⁄8" (Dust Port)...... 4
V
X
T
U
W
Figure 10. Additional component inventory.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
-19-
G0814/G0814X
Inventory
Q
The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
NOTICE
If you cannot find an item on this list, carefully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpacking or they are pre-installed at the factory.
A
C
B
D
F
G
E
J
I
H
K
M
N
O
P
R
Figure 12. Additional component inventory.
Component Inventory (Figures 11-12)
Qty
A. Jointer Assembly w/Carriage Mount............ 1
B. Fence Assembly & Carriage....................... 1
C. Cutterhead Guard........................................ 1
D. Belt Guard................................................... 2
E. Knife-Setting Jig (G0814)............................ 1
F. Push Blocks................................................. 2
G. Hex Wrench 3mm (G0814)....................1 Ea.
H. Belt.............................................................. 1
I.Fence Lock w/Locking Nut.......................... 1
J. Fence Tilt Handle........................................ 1
K. Open-End Wrenches 8/10, 12/14mm....1 Ea.
L. T-Handle Torx Wrench 1⁄4" (G0814X)............ 1
M. T20 Torx Bits (G0814X)................................ 5
N. Flat HD Torx Screws M6-1 x 15 (G0814X).... 10
O. Indexable Inserts 15 x 15 x 2.5 (G0814X).... 5
P. Dust Port..................................................... 1
Q. Stand Assembly w/Motor............................ 1
R. Foot Pedal Caster Assembly....................... 1
Fasteners (see Hardware Recognition Chart)
•
Hex Bolts 3 ⁄ 8"-16 x 21⁄ 2" (Wheel/Stand)........ 2
•
Flat Washers 3 ⁄ 8" (Wheel/Stand)................. 4
•
Hex Nuts 3 ⁄ 8"-16 (Wheel/Stand)................... 2
•
Hex Bolt 5 ⁄ 16"-18 x 2" (Wheel/Stand)............ 1
•
Flat Washer 5 ⁄ 16" (Wheel/Stand).................. 1
•
Hex Bolts 3 ⁄ 8"-16 x 3 ⁄4" (Jointer/Stand).......... 3
•
Flat Washers 3 ⁄ 8" (Jointer/Stand)................. 3
•
Hex Bolt 5 ⁄ 16"-18 x 21⁄ 2" (Belt Guard)............ 1
•
Flat Washer 5 ⁄ 16" (Belt Guard)...................... 1
•
Flange Screws #10-24 x 3⁄8" (Dust Port)...... 4
L
Figure 11. Component inventory.
-20-
Model G0813/G0814/G0814X (Mfd. Since 10/19)
Hardware Recognition Chart
USE THIS CHART TO MATCH UP
HARDWARE DURING THE INVENTORY
AND ASSEMBLY PROCESS.
Flat
Head
Cap
Screw
5mm
5mm
Model G0813/G0814/G0814X (Mfd. Since 10/19)
-21-
Cleanup
Cleanup
The unpainted surfaces of your machine are
coated with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
This rust preventative works extremely well, but it
will take a little time to clean.
Be patient and do a thorough job cleaning your
machine. The time you spend doing this now will
give you a better appreciation for the proper care
of your machine's unpainted surfaces.
There are many ways to remove this rust preventative, but the following steps work well in a wide
variety of situations. Always follow the manufacturer’s instructions with any cleaning product you
use and make sure you work in a well-ventilated
area to minimize exposure to toxic fumes.
Before cleaning, gather the following:
•
Disposable rags
•
Cleaner/degreaser (WD•40 works well)
•
Safety glasses & disposable gloves
•
Plastic paint scraper (optional)
Basic steps for removing rust preventative:
1.
Put on safety glasses.
2.
Coat the rust preventative with a liberal
amount of cleaner/degreaser, then let it soak
for 5–10 minutes.
3.
Wipe off the surfaces. If your cleaner/degreaser is effective, the rust preventative will wipe
off easily. If you have a plastic paint scraper,
scrape off as much as you can first, then wipe
off the rest with the rag.
4.
Repeat Steps 2–3 as necessary until clean,
then coat all unpainted surfaces with a quality
metal protectant to prevent rust.
-22-
Gasoline and petroleum
products have low flash
points and can explode
or cause fire if used to
clean machinery. Avoi d
u sing t h e s e p r o d u c t s
to c l e a n m a c hin e r y.
Many cleaning solvents
are toxic if inhaled. Only
work in a well-ventilated
area.
NOTICE
Avoid harsh solvents like acetone or brake
parts cleaner that may damage painted surfaces. Always test on a small, inconspicuous location first.
T23692—Orange Power Degreaser
A great product for removing the waxy shipping grease from the non-painted parts of the
machine during clean up.
Figure 13. T23692 Orange Power Degreaser.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
Site Considerations
Weight Load
Physical Environment
Refer to the Machine Data Sheet for the weight
of your machine. Make sure that the surface upon
which the machine is placed will bear the weight
of the machine, additional equipment that may be
installed on the machine, and the heaviest workpiece that will be used. Additionally, consider the
weight of the operator and any dynamic loading
that may occur when operating the machine.
The physical environment where the machine is
operated is important for safe operation and longevity of machine components. For best results,
operate this machine in a dry environment that is
free from excessive moisture, hazardous chemicals, airborne abrasives, or extreme conditions.
Extreme conditions for this type of machinery are
generally those where the ambient temperature
range exceeds 41°–104°F; the relative humidity
range exceeds 20%–95% (non-condensing); or
the environment is subject to vibration, shocks,
or bumps.
Space Allocation
Consider the largest size of workpiece that will
be processed through this machine and provide
enough space around the machine for adequate
operator material handling or the installation of
auxiliary equipment. With permanent installations,
leave enough space around the machine to open
or remove doors/covers as required by the maintenance and service described in this manual.
See below for required space allocation.
Children or untrained people
may be seriously injured by
this machine. Only install in an
access restricted location.
Electrical Installation
Place this machine near an existing power source.
Make sure all power cords are protected from
traffic, material handling, moisture, chemicals, or
other hazards. Make sure to leave enough space
around machine to disconnect power supply or
apply a lockout/tagout device, if required.
Lighting
Lighting around the machine must be adequate
enough that operations can be performed safely.
Shadows, glare, or strobe effects that may distract
or impede the operator must be eliminated.
Wall
Min. 30"
for Maintenance
471/2"
20"
= Electrical Connection
Figure 14. Minimum working clearances.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
-23-
Assembly
2.
The machine must be fully assembled before it
can be operated. Before beginning the assembly
process, refer to Needed for Setup and gather
all listed items. To ensure the assembly process
goes smoothly, first clean any parts that are covered or coated in heavy-duty rust preventative (if
applicable).
The Model G0813 jointer stand must be assembled. The Model G0814/G0814X stand requires
no assembly. Therefore, if assembling the Model
G0813, start at Step 1. If assembling the Model
G0814/G0814X, start at Step 18 on Page 27.
Hold motor mount plate level, attach it to top
of chute supports with (2) #10-24 x 3⁄8" flange
screws, then pivot plate down and install
(4) #10-24 x 3⁄8" additional flange screws
(see Figure 16).
Note: Flange screws must be installed from
inside of chute supports.
x6
Motor
Mount
Plate
Chute
Support
To assemble jointer:
1.
Place top plate upside down on level surface,
then attach left and right chute supports to
top plate with (4) #10-24 x 3⁄8" flange screws
and #10-24 hex nuts, as shown in Figure 15.
Ensure flanges face outward.
Figure 16. Motor mount plate attached to chute
supports.
3.
Left
Support
Top Plate
Flange
Right Support
Attach motor to base so pulley is aligned with
belt slot in top plate using (4) 5⁄16"-18 x 5⁄8"
carriage bolts, (4) 5⁄16" flat washers, and (4)
5
⁄16"-18 hex nuts (see Figure 17).
Note: Do not tighten any fasteners until
further instructed.
Pulley
x4
Figure 15. Dust chute supports attached to top
plate.
Belt Slot
x4
Dust Chute
Base
Figure 17. Motor attached to dust chute base.
-24-
Model G0813/G0814/G0814X (Mfd. Since 10/19)
4.
Attach each of the four corner supports to top
plate with (4) #10-24 x 3⁄8" flange screws, as
shown in Figure 18. Ensure flange of each
support is installed inside top plate.
6.
Corner
Support
Attach motor cord and power cord wires to
ON/OFF switch terminals (see Figure 20).
Ensure motor cord wires attach to horizontal
terminals and power cord wires attach to vertical terminals.
Horizontal Terminal
Motor Cord GND
GND
x4
Power Cord
Figure 18. Corner supports attached to top
plate.
5.
Attach front and rear panels to corner supports with (7) #10-24 x 3⁄8" flange screws each
(see Figure 19). Orient panels upside down
so ON/OFF switch (front panel) and power
cord (rear panel) are at bottom.
Rear
Panel
Power
Cord
Horizontal
Terminal
Vertical
Terminal
GND
ON/OFF
Switch
GND
Power
Cord
Motor
Cord
Front
Panel
Vertical
Terminal
Figure 20. Wires connected to ON/OFF switch
terminals.
7.
Attach switch box to front panel with (2) preinstalled #10-24 x 3⁄8" flange screws (see
Figure 21).
Front
Panel
Motor
Cord
x7
Figure 19. Front and rear panels attached to
corner supports.
x2
Switch Box
Figure 21. Switch box attached to front panel.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
-25-
8.
Remove motor junction box cover, loosen
strain relief, then insert motor cord into junction box, as shown in Figure 22.
9.
Attach ground wire with pre-installed ground
wire screw (see Figure 22).
Strain Relief
Right
Panel
Ground
Wire Screw
Figure 22. Inserting wires into junction box.
10. Remove wire nuts (see Figure 22) and disconnect wires, then use wire nuts to reconnect wires, as indicated in Figure 23. Twist
wire nuts onto their respective wires and
wrap them with electrical tape so they will not
come loose (see Figure 23).
15. Attach left panel with dust chute to corner
supports using (6) #10-24 x 3⁄8" flange screws
(see Figure 25).
Left
Panel
To Switch
x6
Ground
Figure 23. Wires connected inside motor
junction box.
11. Make sure wires have enough slack between
strain relief and wire nuts so they are not
pulled tight or stretched, then tighten strain
relief against outer jacket of cord to secure it.
12. Test strain relief to ensure it is properly
tightened by pulling cord from outside junction box with light-to-moderate force. When
strain relief is properly tightened, cord will not
move inside junction box.
13. Re-install junction box cover.
-26-
x6
Figure 24. Right panel attached to stand.
Wire Nut (1 of 2)
Connect
Wire Nuts
and Wires
14. Attach right panel to corner supports with (6)
#10-24 x 3⁄8" flange screws (see Figure 24).
Figure 25. Left panel attached to stand.
16. Position mobile base chassis on stand so
wheels are on same side as dust chute, then
secure base with (4) 3⁄8"-16 x 1" hex bolts, (8)
3
⁄8" flat washers, and (4) 3⁄8"-16 hex nuts, as
shown in Figure 26.
Chassis
Dust Chute
x4
Figure 26. Mobile base chassis attached to
stand.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
17. Tighten all fasteners on stand.
18. G0814/G0814X Only: Turn stand upside
down and place top on flat surface.
19. Attach foot pedal caster assembly to side of
mobile base chassis with leveling feet, using
(2) 3⁄8"-16 x 21⁄2" hex bolts, (4) 3⁄8" flat washers, (2) 3⁄8"-16 hex nuts, and (1) 5⁄16"-18 x 2"
hex bolt and (1) 5⁄16" flat washer, as shown in
Figure 27.
22. With help of another person, place jointer
assembly onto stand. Attach jointer assembly
to stand with (3) 3⁄8"-16 x 3⁄4" hex bolts and (3)
3
⁄8" flat washers (see Figure 28).
Note: Mounting requires reaching through
dust chute to install a hex bolt and washer on
left side of stand. Ensure cutterhead pulley is
positioned above slot in top of cabinet stand.
x2
Slot
x3
Figure 28. Jointer assembly attached to stand.
(Interior View)
23. Place straightedge against pulleys to check
their alignment (see Figures 29–30).
— If pulleys are aligned, go to Step 25.
— If pulleys are not aligned, go to Step 24.
x1
Figure 27. Pedal assembly attached to right side
of stand.
20. Place stand in upright position and adjust leveling feet as needed with hex nuts so stand
rests level and stable on floor.
21. Remove rear panel to access mounting holes
in stand during next step.
Straightedge
Figure 29. Checking belt alignment.
Cutterhead
Pulley
Alignment
Motor
Pulley
Figure 30. Pulley alignment.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
-27-
24. Loosen set screws on cutterhead or motor
pulley as needed to align pulleys, then tighten
set screws (see Figure 31).
x2
27. Adjust belt tension by applying downward
pressure on motor until there is approximately 1⁄4" deflection when belt is pushed with
moderate force, as shown in Figure 34.
Note: After the first 16 hours of operation,
check and re-tension the belt, as it may
stretch and seat during this time, which will
cause it to lose the initial tension you set.
Pulley
Cutterhead Pulley
Figure 31. Motor pulley set screw locations.
Approximately
1
/4" Deflection
25. Loosen motor mount bolts shown in Figure
32, but DO NOT completely remove them.
Motor Pulley
Figure 34. Correct belt deflection when properly
tensioned.
28. Tighten motor mount bolts/nuts (see Figure
32) and replace rear panel.
29. Place fence onto fence carriage base, making sure it fits over key (see Figure 35), then
insert fence lock and thread on locking nut.
Figure 32. Location of motor mount bolts/nuts
(2 of 4 shown).
Top View
Fence
Lock
26. Slide motor upward, place belt around
cutterhead and motor pulleys, then slide
motor down to rest on belt (see Figure 33).
Belt
Fence
Carriage
Base
Key
Bottom View
Fence
Lock
Figure 33. Belt installed onto cutterhead and
motor pulleys.
-28-
Figure 35. Fence assembly installed onto
carriage base and secured with fence lock.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
30. Install fence tilt lever (see Figure 36).
Tilt Lever
32. Remove set screw from forked end of
cutterhead guard shaft, wind torsion spring
knob 1⁄2-turn counterclockwise (viewed from
top), then slide shaft down through mounting
hole on table.
Note: The guard may not fully seat in hole initially; however, rotating guard will allow shaft
to fully seat in hole.
Figure 36. Fence tilt lever installed.
The outfeed table MUST be level with
cutterhead knives/inserts when they are
at top dead center (at their highest point
during rotation). Otherwise, the workpiece
cannot properly feed past the cutterhead,
which may cause a kickback hazard for
the operator.
31. Verify outfeed table height is set correctly
with knives/inserts at top dead center (TDC)
(refer to Setting Outfeed Table Height on
Page 51) and all knives/inserts are securely
tightened in cutterhead.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
33. Thread set screw through forked end of
cutterhead guard shaft, as shown in Figure 37.
When properly installed, guard is positioned
3
⁄8" above table for safety during operations.
Torsion
Spring
Knob
Forked End of
Shaft
Figure 37. Set screw threaded into end of
cutterhead guard shaft.
-29-
36. G0813/G0814 Only: Assemble knife-setting
gauge, as shown in Figure 39.
Cutterhead guard must always return to
closed position whenever it is moved. If it
does not do this, it must be re-adjusted or
re-installed.
34. Test operation of guard by pulling it back.
Guard should spring back over cutterhead
and stop against fence.
— If guard does not snap back, or snaps
back slowly, remove guard and repeat
Steps 32–34.
35. Install belt guard with (1) 5⁄16"-18 x 21⁄2" hex
bolt and (1) 5⁄16" flat washer (see Figure 38).
Figure 39. Knife-setting gauge assembled.
37. Install dust port, as shown in Figure 40, using
(4) #10-24 x 3⁄4" flange screws.
x1
x4
Figure 38. Belt guard installed.
Figure 40. Dust port installed.
-30-
Model G0813/G0814/G0814X (Mfd. Since 10/19)
Dust Collection
This machine creates a lot of wood chips/
dust during operation. Breathing airborne
dust on a regular basis can result in permanent respiratory illness. Reduce your risk
by wearing a respirator and capturing the
dust with a dust-collection system.
Recommended CFM at Dust Port: 400 CFM
Do not confuse this CFM recommendation with
the rating of the dust collector. To determine the
CFM at the dust port, you must consider these
variables: (1) CFM rating of the dust collector,
(2) hose type and length between the dust collector and the machine, (3) number of branches
or wyes, and (4) amount of other open lines
throughout the system. Explaining how to calculate these variables is beyond the scope of
this manual. Consult an expert or purchase a
good dust collection "how-to" book.
To connect dust collection hose:
1.
Fit 4" dust hose over dust port, as shown in
Figure 41, and secure with a hose clamp.
Test Run
Once assembly is complete, test run the machine
to ensure it is properly connected to power and
safety components are functioning correctly.
If you find an unusual problem during the test run,
immediately stop the machine, disconnect it from
power, and fix the problem BEFORE operating the
machine again. The Troubleshooting table in the
SERVICE section of this manual can help.
Serious personal injury could occur from
connecting machine to power before
completing the setup process described in
this manual. DO NOT connect power until
instructed to do so later in this manual.
DO NOT start machine until all preceding
setup instructions have been performed.
Operating an improperly set up machine
may result in malfunction or unexpected results that can lead to serious injury,
death, or machine/property damage.
To test run the machine:
1.
Clear all setup tools away from machine.
2.
Connect machine to power supply.
3.
Turn machine ON, verify motor operation,
and then turn machine OFF.
The motor should run smoothly and without
unusual problems or noises.
Figure 41. Example of dust hose attached to
dust port.
2.
Tug hose to make sure it does not come off.
Note: A tight fit is necessary for proper
performance.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
-31-
4.
Recommended
Adjustments
Remove switch disabling key, as shown in
Figure 42.
For your convenience, the adjustments listed
below have been performed at the factory and no
further setup is required to operate your machine.
However, because of the many variables involved
with shipping, we recommend that you at least
verify the following adjustments to ensure the best
possible results from your new machine.
Figure 42. Removing switch key from paddle
switch.
5.
Try to start machine with paddle switch. The
machine should not start.
— If the machine does not start, the switch
disabling feature is working as designed.
Congratulations! The test run is complete.
Proceed to Recommended Adjustments.
— If the machine does start, immediately stop
the machine. The switch disabling feature
is not working correctly. This safety feature must work properly before proceeding
with regular operations. Call Tech Support
for help.
-32-
Step-by-step instructions for these adjustments
can be found in SECTION 7: SERVICE.
Factory adjustments that should be verified:
1.
Knife/Insert Settings (Pages 48 & 50).
2.
Depth Scale Calibration (Page 52).
3.
Fence Stop Accuracy (Page 54).
4.
Table Parallelism (Page 57).
Model G0813/G0814/G0814X (Mfd. Since 10/19)
SECTION 4: OPERATIONS
Operation Overview
To complete a typical operation with the
jointer, the operator does the following:
The purpose of this overview is to provide the novice machine operator with a basic understanding
of how the machine is used during operation, so
the machine controls/components discussed later
in this manual are easier to understand.
1.
Examines workpiece to verify it is safe and
suitable for cutting.
2.
Adjusts fence for width of workpiece and
locks it in place.
Due to the generic nature of this overview, it is
not intended to be an instructional guide. To learn
more about specific operations, read this entire
manual, seek additional training from experienced
machine operators, and do additional research
outside of this manual by reading "how-to" books,
trade magazines, or websites.
3.
Adjusts fence tilt, if necessary.
4.
Adjusts infeed table height to set depth of cut
per pass.
5.
Puts on safety glasses, respirator, and any
other required protective equipment.
6.
Starts jointer.
7.
Using push blocks as needed, holds workpiece firmly against infeed table and fence,
and feeds workpiece into cutterhead at a
steady and controlled rate until entire length
of workpiece has been cut and it clears the
cutterhead on the outfeed table side.
8.
Repeats cutting process described above
until desired results are achieved.
9.
Stops jointer.
To reduce your risk of
serious injury, read this
entire manual BEFORE
using machine.
To reduce risk of eye injury from flying
chips or lung damage from breathing dust,
always wear safety glasses and a respirator
when operating this machine.
If you are not experienced with this type
of machine, WE STRONGLY RECOMMEND
that you seek additional training outside of
this manual. Read books/magazines or get
formal training before beginning any projects. Regardless of the content in this section, Grizzly Industrial will not be held liable
for accidents caused by lack of training.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
-33-
Stock Inspection &
Requirements
Follow these rules when choosing and jointing
stock:
•
DO NOT joint or surface plane stock that
contains large or loose knots. Injury to the
operator or damage to the workpiece can
occur if a knot becomes dislodged during the
cutting operation.
•
DO NOT joint or surface plane against the
grain direction. Cutting against the grain
increases the likelihood of kickback, as well
as tear-out on the workpiece.
Jointing and surface planing with the
grain produces a better finish and is safer
for the operator. Cutting with the grain is
described as feeding the stock on the jointer so
the grain points down and toward you as viewed
on the edge of the stock (see Figure below).
•
Note: If the grain changes direction along the
edge of the board, decrease the cutting depth
and make additional passes.
CORRECT
•
Scrape all glue off the workpiece before
jointing. Glue deposits on the workpiece,
hard or soft, will gum up the cutterhead and
produce poor results.
•
Remove foreign objects from the workpiece. Make sure that any stock you process with the jointer is clean and free of dirt,
nails, staples, tiny rocks or any other foreign
objects that could damage the cutterhead.
These particles could also cause a spark as
they strike the cutterhead and create a fire
hazard.
IMPORTANT: Wood stacked on a concrete
or dirt surface can have small pieces of concrete or stone pressed into the surface.
•
Make sure all stock is sufficiently dried
before jointing. Wood with a moisture content over 20% will cause unnecessary wear
on the cutters and poor cutting results. Excess
moisture can also hasten rust and corrosion.
Edge Jointing
10" Min.
Make sure your workpiece exceeds the
minimum dimension requirements shown
below3 before processing it through the
" Min.
jointer,/4or
the workpiece may break or kick
back during the operation.
1
/4" Min.
Edge Jointing
10" Min.
With Grain
INCORRECT
/4" Min.
3
Against Grain
/4" Min.
1
Surface Planing
Figure 43. Proper grain alignment with cutterhead.
•
-34-
Only cut natural wood. This jointer is only
designed for cutting natural wood stock.
Never use it to cut MDF, particle board, plywood, laminates, drywall, backer board, metals,
glass, stone, tile, products with lead-based
paint, or products that contain asbestos. Cutting
these may lead to injury or machine damage.
10" Min.
/2" Min.
1
1" Min.
Figure 44. Minimum stock dimensions for jointer.
Surface Planing
Model G0813/G0814/G0814X (Mfd. Since 10/19)
10" Min.
Setting Depth of Cut
The depth of cut on a jointer is the amount of material removed from the bottom of the workpiece as
it passes over the cutterhead.
The depth of cut is set by adjusting the height of
the infeed table relative to the cutterhead knives/
inserts at TDC (top dead center).
Depth-of-Cut Scale
The depth of cut can be referenced directly from
the depth scale located on the front of the jointer
(see Figures 46–47).
Note: The depth scale can be calibrated or
"zeroed" if it is not correct. Refer to Calibrating
Depth Scale on Page 52 for more information.
The depth-of-cut scale (see Figure 47 on this
page) goes up to 1⁄ 2" for cutting rabbets, but for
all other types of cuts the maximum depth of cut
should never exceed 1⁄ 8".
DO NOT exceed the recommended depth of
cut per pass (1 ⁄ 16" or 1 ⁄ 8" depending on the
operation), or kickback and serious injury
may occur.
Adjusting Infeed Table Height
To adjust the infeed table height, loosen the infeed
table lock, adjust the infeed table lever, then tighten the lock to secure the setting (see Figure 45).
To set the maximum height (i.e. minimum depth of
cut), thread the stop bolt into the base and tighten
the jam nut shown in Figure 47.
Figure 46. Location of depth-of-cut scale.
Depth
Indicator
Scale
Stop Bolt
Jam Nut
Figure 47. Depth-of-cut scale components.
Infeed Table Lock
Infeed Table
Lever
Figure 45. Infeed table controls located on back
of machine.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
-35-
Squaring Stock
3.
Edge Joint on Jointer—Concave edge of
workpiece is jointed flat with jointer.
4.
Rip Cut on a Table Saw—Jointed edge
of workpiece is placed against a table saw
fence and opposite edge cut off.
Squaring stock involves four steps performed
in the order below:
1.
2.
Surface Plane on Jointer—Concave face of
workpiece is surface planed flat with jointer.
Surface Plane on a Thickness Planer—
Opposite face of workpiece is surface planed
flat with a thickness planer.
Previously
Jointed
Edge
45
15
30
Previously Surface
Planed Face
-36-
Model G0813/G0814/G0814X (Mfd. Since 10/19)
Surface Planing
The purpose of surface planing (see example
Figures below) on the jointer is to make one flat
face on a piece of stock to prepare it for thickness
planing on a planer.
Failure to use push blocks when surface
planing could result in your hands contacting rotating cutterhead, which will cause
serious personal injury. ALWAYS use push
blocks when surface planing on jointer!
To surface plane on jointer:
1.
Inspect stock to ensure it is safe and suitable
for the operation (see Stock Inspection &
Requirements section).
2.
Set infeed table height to desired cutting
depth for each pass.
CAUTION: To minimize risk of kickback,
do not exceed a cutting depth of 1⁄16" per pass
when surface planing.
3.
Set fence to 90°.
4.
Start jointer.
5.
Place workpiece firmly against fence and
infeed table.
CAUTION: To ensure workpiece remains
stable during cut, concave sides of workpiece
must face toward table and fence.
6.
Feed workpiece completely across cutterhead while keeping it firmly against fence
and tables during the entire cut.
CAUTION: Keep hands at least 4" away
from cutterhead during the entire cut. Instead
of allowing a hand to pass directly over cutterhead, lift it up and over cutterhead, and
safely reposition it on the outfeed side to continue supporting workpiece. Use push blocks
whenever practical to further reduce risk of
accidental hand contact with cutterhead.
7.
Removed
Surface
Repeat Step 6 until entire surface is flat.
Tip: When squaring up stock, cut opposite
side of workpiece with a planer instead of the
jointer to ensure boths sides are parallel.
Figure 48. Example photo of a surface planing
operation.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
-37-
Edge Jointing
Edge jointing (see example Figures below) produces a flat and true surface along the side of
a workpiece by removing uneven areas. It is an
essential step for squaring up warped or rough
stock and when preparing a workpiece for joinery
or finishing.
To edge joint on jointer:
1.
Inspect stock to ensure it is safe and suitable
for the operation (see Stock Inspection &
Requirements section).
2.
Set infeed table height to desired cutting
depth for each pass.
CAUTION: To minimize risk of kickback,
do not exceed a cutting depth of 1⁄8" per pass.
3.
Set fence to 90°.
4.
Start jointer.
5.
Place workpiece firmly against fence and
infeed table.
CAUTION: To ensure workpiece remains
stable during cut, concave sides of workpiece
must face toward table and fence.
6.
Removed
Surface
Figure 49. Example photo of an edge jointing
operation.
-38-
Feed workpiece completely across cutterhead while keeping it firmly against fence
and tables during the entire cut.
CAUTION: Keep hands at least 4" away
from cutterhead during the entire cut. Instead
of allowing a hand to pass directly over cutterhead, lift it up and over cutterhead, and
safely reposition it on the outfeed side to continue supporting workpiece. Use push blocks
whenever practical to further reduce risk of
accidental hand contact with cutterhead.
7.
Repeat Step 6 until the entire edge is flat.
Tip: When squaring up stock, cut opposite
edge of workpiece with a table saw instead
of the jointer—otherwise, both edges of workpiece will not be parallel with each other.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
Bevel Cutting
Bevel cuts (see example Figures below) can be
made by setting the fence at the desired angle
and feeding the workpiece firmly along the fence
face, with the bottom inside corner firmly against
the table. The cutting process typically requires
multiple passes or cuts to bevel the entire edge
of a workpiece.
To bevel cut on jointer:
1.
Inspect stock to ensure it is safe and suitable
for the operation (see Stock Inspection &
Requirements section).
2.
Set infeed table height to cutting depth
desired for each pass.
CAUTION: Cutting depth for bevel cuts is
typically between 1⁄16" and 1⁄8", depending on
hardness and width of stock.
3.
Set fence tilt to desired angle of cut.
4.
Place workpiece against fence and infeed
table with concave side face down.
5.
Start jointer.
6.
With a push block in your leading hand, press
workpiece against table and fence with firm
pressure, and feed workpiece over cutterhead with a push block in your trailing hand.
CAUTION: When your leading hand gets
within 4" of the cutterhead, lift it up and over
cutterhead, and place push block on portion
of the workpiece once it is 4" past cutterhead.
Now, focus your pressure on outfeed end
of the workpiece while feeding, and repeat
same action with your trailing hand when it
gets within 4" of cutterhead. To help keep
your hands safe, DO NOT let them get closer
than 4" from moving cutterhead at any time
during operation!
Removed
Surface
7.
Repeat cutting process, as necessary, until
you are satisfied with the results.
Figure 50. Example photo of fence setup for a
bevel cut of 45°.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
-39-
Rabbet Cutting
A rabbet cut removes a portion of a workpiece
edge, so it fits together with an opposing, equally
sized rabbet cut on another workpiece (see example Figure below). This is a classic method of
joining two workpieces that is simple, yet strong.
To rabbet cut on jointer:
1.
Inspect stock to ensure it is safe and suitable
for the operation (see Stock Inspection &
Requirements section).
2.
Set infeed table height to desired cutting
depth for each pass.
CAUTION: For safety reasons, cutting
depth should never exceed 1⁄8" per pass.
Removed
Surface
3.
Remove cutterhead guard if necessary to perform operation (see Figures below.)
Guard Installed
Rabbet Joints
This jointer can be used to make high-quality rabbet cuts, but there are some situations—whether
it is due to an excessively large/small workpiece
size or rabbet cutting width/depth—when it will not
be safe or appropriate for making the rabbet cut
on this jointer. In these cases, you need to use
another tool or method for rabbet cutting that will
be a safer alternative.
Guard Removed
A rabbet cut can alternatively be made using a
table saw, router, or even a hand saw. As with any
type of cutting operation, always consider your
safety first and use good judgement!
Typically, rabbet cutting with a jointer requires
the cutterhead guard to be removed first, so the
workpiece can slide along the rabbeting ledge
during the cut. However, it is possible to make
rabbet cuts with workpieces up to 1" thick without
removing the cutterhead guard. This is done by
performing the rabbet cut with the workpiece on
end (similar to when you are edge jointing).
-40-
Figure 51. Examples of typical rabbet cutting
operations.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
7.
When cutterhead guard is removed,
attempting any other cut besides a rabbet
directly exposes operator to moving cutterhead. To minimize risk of injury and unnecessary exposure to cutterhead, always
keep cutterhead guard installed when possible, and ALWAYS immediately replace it
after performing rabbet cuts.
4.
Set fence to 90° and near front of jointer,
so amount of exposed cutterhead in front of
fence matches size of desired rabbet.
5.
Start jointer.
6.
Place workpiece firmly against fence and
infeed table.
Feed workpiece completely across cutterhead
while keeping it firmly against fence and
tables during entire cut.
CAUTION: Keep hands at least 4" away
from cutterhead during the entire cut. Instead
of allowing a hand to pass directly over
cutterhead, lift it up and over cutterhead, and
safely reposition it on the outfeed side to continue supporting workpiece. Use push blocks
whenever practical to further reduce risk of
accidental hand contact with cutterhead.
8.
Repeat Step 7 until rabbet is cut to depth.
9.
Re-install cutterhead guard if removed in
Step 3.
CAUTION: To ensure workpiece remains
stable during cut, concave sides of workpiece
must face toward table and fence.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
-41-
ACCESSORIES
SECTION 5: ACCESSORIES
Basic Eye Protection
Installing unapproved accessories may
cause machine to malfunction, resulting in
serious personal injury or machine damage.
To reduce this risk, only install accessories
recommended for this machine by Grizzly.
T20501—Face Shield Crown Protector 4"
T20502—Face Shield Crown Protector 7"
T20503—Face Shield Window
T20451—“Kirova” Clear Safety Glasses
T20452—“Kirova” Anti-Reflective S. Glasses
T20456—DAKURA Safety Glasses, Black/Clear
NOTICE
T20502
T20452
Refer to our website or latest catalog for
additional recommended accessories.
T20503
W1210A—Jointer Pal® Magnetic Knife Gauge
(Up to 8", polycarbonate body)
W1211A—Jointer Pal® Magnetic Knife Gauge
(Up to 8", all-steel body)
This magnetic knife-setting system lets you set
jointer knives in perfect alignment every time!
T20451
T20456
Figure 54. Assortment of basic eye protection.
Figure 52. W1211A Jointer Pal® Knife Gauge.
H2499—Small Half-Mask Respirator
H3631—Medium Half-Mask Respirator
H3632—Large Half-Mask Respirator
H3635—Cartridge Filter Pair P100
If you work around dust everyday, a half-mask
respirator can be a lifesaver. Also compatible with
safety glasses!
D1123—Jointer/Planer Knife Hone
This handy tool sharpens flat and beveled surfaces quickly and easily. Great for touch-ups.
Figure 55. Half-mask respirator with disposable
cartridge filters.
Figure 53. D1123 Jointer Knife Hone.
order online at www.grizzly.com or call 1-800-523-4777
-42-
Model G0813/G0814/G0814X (Mfd. Since 10/19)
G0777—1.5 HP Ultra-Quiet Cyclone Dust Collector
Where most dust collectors this size operate at a
minimum of 80-82 dB, the G0777 can collect even
the biggest shavings without exceeding 70–72 dB
due to its slow-speed motor and large impeller.
Features a compact profile on a sturdy mobile
frame, a pleated filter system, an internal filtercleaning brush system, 880 CFM airflow, a builtin remote control switch, and a mobile 35-gallon
collection drum.
T32014—Indexable Carbide Inserts, 10 Pk.
15 x 15 x 2.5mm replacement indexable carbide
inserts for the G0814X.
Figure 58. Replacement carbide inserts for the
Model G0814X.
G6697—6" x 1" x 1 ⁄ 8" HSS Jointer Knives,
Set of 3
These jointer knives are made from M-2 high
speed steel and are hardened to 62–64 Rockwell
and tempered in a salt bath. All sets are balanced
to within one gram.
Figure 56. G0777 Ultra-Quiet Cyclone
Dust Collector.
T23246—The Missing Shop Manual: Jointer
Dedicated to providing integral information about
woodworking tools and techniques that other
manuals overlook, the books in this series contain safety facts, explanations about basic project
set-up, and tips for maximizing tool performance.
Figure 59. G6697 Replacement Knives for
Models G0813/G0814.
Figure 57. Instructional reference book.
order online at www.grizzly.com or call 1-800-523-4777
Model G0813/G0814/G0814X (Mfd. Since 10/19)
-43-
SECTION 6: MAINTENANCE
To reduce risk of shock or
accidental startup, always
disconnect machine from
power before adjustments,
maintenance, or service.
Schedule
For optimum performance from this machine, this
maintenance schedule must be strictly followed.
Cleaning &
Protecting
The cleaning process for this machine is simple.
Vacuum excess wood chips and sawdust, and
wipe off the remaining dust with a dry cloth. If any
resin has built up, use a resin dissolving cleaner
to remove it. Treat all unpainted cast iron and steel
with a non-staining lubricant after cleaning.
Protect the unpainted cast iron surfaces on the
table by wiping the table clean after every use—
this ensures moisture from wood dust does not
remain on bare metal surfaces.
Ongoing
To minimize your risk of injury and maintain proper
machine operation, shut down the machine immediately if you ever observe any of the items below,
and fix the problem before continuing operations:
Keep tables rust-free with regular applications of
products like G96® Gun Treatment, SLIPIT®, or
Boeshield ® T-9.
•
•
•
•
•
•
G5562—SLIPIT® 1 Qt. Gel
G5563—SLIPIT® 12 Oz. Spray
G2871—Boeshield® T-9 12 Oz. Spray
G2870—Boeshield® T-9 4 Oz. Spray
H3788—G96® Gun Treatment 12 Oz. Spray
H3789—G96® Gun Treatment 4.5 Oz. Spray
Loose mounting bolts.
Dust or debris on and around machine.
Dull or damaged cutterhead knives/inserts.
Unprotected cast-iron surfaces.
Worn or damaged wires.
Any other unsafe condition.
Monthly Check
•
V-belt tension, damage, or wear (Page 55).
•
Clean/vacuum dust buildup from inside cabinet and off motor.
Figure 60. Recommended products for
protecting unpainted cast-iron and steel.
-44-
Model G0813/G0814/G0814X (Mfd. Since 10/19)
Lubrication
Since all bearings are sealed and permanently
lubricated, simply leave them alone until they
need to be replaced. DO NOT lubricate them.
It is essential to clean components before lubricating them because dust and chips build up on
lubricated components and make them hard to
move. Simply adding more grease to them will not
yield smooth moving components.
Table Ways
Oil Type..... Grizzly T23962 or ISO 68 Equivalent
Oil Amount............................................1–2 Drops
Lubrication Frequency........................ As Needed
Lower infeed and outfeed tables to access ways.
Place a couple of drops of oil at top of each way
as needed, and move tables up and down to distribute oil (see Figure 63). Wipe off excess oil.
Clean the components below with mineral spirits
or other oil/grease solvent cleaner and shop rags.
Outfeed Table Leadscrew
Oil Type.................SB1365 or ISO 68 Equivalent
Oil Amount.............................................Thin Coat
Frequency........................................... As Needed
Lubricate the outfeed table leadscrew with light
machine oil as needed (see Figure 61). Wipe off
excess oil and sawdust with a cloth.
Figure 63. Location to lubricate table ways.
Fence
Oil Type..... Grizzly T23962 or ISO 68 Equivalent
Oil Amount............................................1–2 Drops
Lubrication Frequency........................ As Needed
Place one or two drops of light machine oil on
fence pivot points (see Figure 64) as needed.
Figure 61. Leadscrew lubrication location.
SB1365—South Bend Way Oil-ISO 68
Figure 64. Fence lubrication locations.
Figure 62. Recommended product for machine
lubrication.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
-45-
SECTION 7: SERVICE
Review the troubleshooting procedures in this section if a problem develops with your machine. If you need
replacement parts or additional help with a procedure, call our Technical Support. Note: Please gather the
serial number and manufacture date of your machine before calling.
Troubleshooting
Motor & Electrical
Symptom
Possible Cause
Possible Solution
Machine does not
start or a breaker
trips immediately
after startup.
1. Switch disabling key removed.
2. Incorrect power supply voltage/circuit size.
3. Power supply circuit breaker tripped/fuse
blown.
4. Motor wires connected incorrectly.
5. Wiring open/has high resistance.
6. ON/OFF switch at fault.
7. Centrifugal switch at fault.
8. Start capacitor at fault.
9. Motor at fault.
1. Install switch disabling key.
2. Ensure correct power supply voltage/circuit size.
3. Ensure circuit is sized correctly and free of shorts.
Reset circuit breaker or replace fuse.
4. Correct motor wiring connections (Page 59).
5. Check/fix broken, disconnected, or corroded wires.
6. Test/replace switch.
7. Adjust/replace centrifugal switch if available.
8. Test/replace capacitor.
9. Test/repair/replace.
Machine stalls or is
underpowered.
1.
2.
3.
4.
1.
2.
3.
4.
Machine has
vibration or noisy
operation.
Workpiece material not suitable.
Excessive feed rate.
Excessive cutting depth.
Dull knives/inserts.
5. Dust collection problem, causing internal
components to clog up with shavings.
6. Belt slipping; oil/grease on belt.
5.
7. Pulley loose or not properly aligned.
7.
8. Motor overheated.
9. Motor wires connected incorrectly.
8.
9.
1. Motor or other component loose.
1. Replace damaged bolts/nuts; retighten loose bolts/
nuts. Use thread-locking fluid if condition repeats.
2. Tension/replace belt (Page 55).
3. Re-align pulleys (Page 56); replace shaft key;
tighten pulley set screw(s).
4. Fix/replace fan cover; replace loose/damaged fan.
5. Release foot-pedal caster to stabilize machine.
6. Sharpen/replace knives (Page 48); rotate/replace
inserts (Page 50); set knife/insert alignment/height
correctly (Pages 48 & 50).
7. Replace bearing(s)/realign cutterhead.
8. Replace.
9. Test by rotating shaft; rotational grinding/loose shaft
requires bearing replacement.
2. Belt worn/loose; belt slapping cover.
3. Pulley loose or not properly aligned.
4. Motor fan rubbing on fan cover.
5. Foot-pedal caster engaged.
6. Dull knives/inserts.
7. Cutterhead bearings at fault.
8. Centrifugal switch at fault.
9. Motor bearings at fault.
-46-
Ensure workpiece is suitable for jointing (Page 34).
Reduce feed rate.
Reduce cutting depth (Page 35).
Sharpen/replace knives (Page 48); rotate/replace
inserts (Page 50).
Clear blockages; move machine closer to dust
collector; upgrade dust collector.
Tension/replace belt (Page 55); clean belt; ensure
pulleys are aligned (Page 56).
Re-align pulleys (Page 56); replace shaft key;
tighten pulley set screw(s).
Clean motor, let cool, and reduce depth of cut.
Correct motor wiring connections (Page 59).
6.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
Machine Operation
Symptom
Possible Cause
Possible Solution
Table(s) difficult to
adjust.
1. Table lock(s) engaged/partially engaged.
2. Infeed table stop blocking upward
movement.
1. Completely loosen table lock(s) (Page 4).
2. Loosen/reset infeed table stop bolt (Page 35).
Excessive snipe
1. Outfeed table set too low, or knives/inserts
(gouge in end of
set too high.
board that is uneven
with rest of cut).
2. Operator pushing down on trailing end of
workpiece as it leaves cutterhead.
Workpiece stops in
middle of cut.
1. Outfeed table set too high.
Workpiece chipping, 1. Not feeding workpiece to cut "with the
tear-out, or overall
grain."
rough cuts.
2. Dull knives/inserts.
3. Workpiece not suitable for jointing.
4. Nicked or chipped knives/inserts.
5. Feeding workpiece too fast.
6. Excessive cut depth.
7. Lack of proper dust collection or clogged
dust port.
Fuzzy grain.
1. Wood has high moisture content.
2. Dull knives/inserts.
1. Align outfeed table with cutterhead knife/insert at
top dead center (Page 57); adjust height of knives/
inserts evenly with outfeed table (Page 48).
2. Reduce/eliminate downward pressure on trailing
end of workpiece as it leaves cutterhead.
1. Align outfeed table with cutterhead knife/insert at
top dead center (Page 57).
1. Turn the workpiece 180° before feeding again.
2. Sharpen/replace knives (Page 48); rotate/replace
inserts (Page 50).
3. Ensure workpiece is suitable for jointing (Page 34).
4. Replace knives (Page 48); rotate/replace inserts
(Page 50).
5. Reduce feed rate.
6. Reduce cut depth (Page 35).
7. Clear blockages, ensure dust collector is operating
efficiently; upgrade dust collector.
1. Ensure wood moisture content is less than 20%.
Allow to dry if necessary (Page 34).
2. Sharpen/replace knives (Page 48); rotate/replace
inserts (Page 50).
Long lines or ridges 1. Nicked or chipped knives/inserts.
that run along length
of workpiece.
1. Replace knives (Page 48); rotate/replace inserts
(Page 50).
Uneven cutter
marks, wavy
surface, or chatter
marks across face
of workpiece.
1. Feeding workpiece too fast.
2. Knives/inserts not properly adjusted.
1. Reduce feed rate.
2. Properly adjust knives/inserts (Page 48).
Glossy surface;
scorching or
burn marks on
workpiece.
1. Dull knives/inserts.
1. Sharpen/replace knives (Page 48); rotate/replace
inserts (Page 50).
2. Increase feed rate.
2. Feed rate too slow.
Workpiece is
1. Workpiece not held with even pressure
concave or convex
against outfeed table during cut.
along its length after
jointing.
2. Workpiece too uneven at start of operation.
3. Outfeed table not parallel with infeed table.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
1. Apply even downward pressure against workpiece
throughout entire travel along outfeed side during
cut.
2. Take partial cuts to remove extreme high spots
before doing a full pass.
3. Check/Adjust table parallelism (Page 57).
-47-
Setting/Replacing
Knives (G0813/G0814)
Setting the knives correctly is crucial to the proper
operation of the jointer and it plays an important
role in keeping the knives sharp. If one knife is
higher than the others, it will do the majority of the
work, and thus, become dull much faster.
The knife jig included with the jointer is designed
to set all the knives evenly and at the correct
The
cutterhead
on this jointer comes with both
height
in the cutterhead.
jack screws and springs for setting knife height.
Which
one you choose
is a matter
of personal
The
cutterhead
in this jointer
is equipped
with
preference.
only
of these
options of
is
that allow
forone
careful
positioning
jack
screwsHowever,
needed
to set the knives.
the
knives.
There are two options for setting the knives—the
straightedge method and the knife-setting jig
method. Each option has advantages and disadvantages; the correct one for you will be a matter of personal preference. For best results, the
tables must be parallel with each other (refer to
Checking/Adjusting Table Parallelism) and the
outfeed table height must be properly set (refer to
Setting Outfeed Table Height).
Straightedge Method
To check knife height with a straightedge:
1.
DISCONNECT MACHINE FROM POWER!
2.
Remove cutterhead guard or block it open.
3.
Using a straightedge on outfeed table, check
height of each knife at positions as shown.
Black Lines Represent
Straightedge Positions
From Overhead View
Knife at TDC
Straightedge
Outfeed
Infeed
Figure 65. Setting knife height with a straightedge.
A high quality straightedge (or Jointer Pal) is held
flat against the outfeed table and the knife heights
are set to the bottom of the straightedge, as
shown. Because the knife projection height from
the cutterhead is dependent on the outfeed table
height, the outfeed table must be set as described
in Setting Outfeed Table Height for this method
to work correctly.
When using the straightedge method to set the
knives, you will not need to move the outfeed
table once it is set and you will always be assured
that the knives are even with the outfeed table in
their highest point of rotation (TDC)—even if the
cutterhead is not perfectly parallel with the outfeed table.
Item(s) Needed
Qty
Precision Straightedge or Knife-Setting Jig....... 1
Hex Wrench 3mm............................................... 1
Open-End Wrench 8mm.................................... 1
-48-
Figure 66. Setting knife height with a Jointer Pal®.
— Knives are set correctly when they just
touch bottom of straightedge at TDC in
each of straightedge positions.
— If knives do not touch straightedge or they
lift up at any position, then those knives
need to be adjusted (refer to Setting/
Replacing Knives on Page 49).
Model G0813/G0814/G0814X (Mfd. Since 10/19)
Knife-Setting Jig Method
4.
Place knife jig on cutterhead, directly over a
knife.
5.
Closely examine how jig touches cutterhead
and knife. Knife is set correctly when, on
each side of cutterhead, both legs of jig sit
firmly on cutterhead body and middle pad of
jig just touches top edge of knife.
The infeed table is lowered to fit the jig on the
cutterhead, as shown, and the knife heights
are set to just touch the middle pad of the jig.
The knife-setting jig included with the jointer is
designed to set all the knives evenly and at the
correct height in the cutterhead.
—If jig does not sit as described, then that
knife must be reset. Repeat this inspection
with other knives before resetting.
Middle
Pad
Figure 67. Example of knife-setting jig positioned
over cutterhead knife.
Figure 69. Using knife-setting jig to set knife
height.
Loosen
Tighten
Knife
Setting/Replacing Knives
1.
DISCONNECT MACHINE FROM POWER!
2.
Remove cutterhead guard from table and
lower infeed table to 1⁄2" on depth-of-cut
scale. This will provide unrestricted access to
cutterhead.
3.
Remove cabinet rear access panel to expose
cutterhead pulley.
4.
Rotate cutterhead pulley to provide good
access to cutterhead knives.
5.
Loosen cutterhead gib bolts, starting in the
middle, and alternating back and forth until all
gib bolts are loose, but not falling out.
Gib Bolt
Gib
Jack
Screw
Figure 68. Cutterhead profile diagram.
To check knife height with a knife-setting jig:
1.
DISCONNECT MACHINE FROM POWER!
2.
Remove cutterhead guard or block it open.
3.
Lower infeed table to 1⁄2" scale mark.
4.
Place knife jig on cutterhead, directly over a
knife.
5.
Closely examine how jig touches cutterhead
and knife. Knife is set correctly when, on
each side of cutterhead, both legs of jig sit
firmly on cutterhead body and middle pad of
jig just touches top edge of knife.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
—If jig does not sit as described, then that
knife must be reset. Repeat this inspection
The first time you set or replace a knife,
remove gib and knife from cutterhead. Clean
gib and clean inside cutterhead slot to remove
all pitch or sawdust. Coat knife and gib with a
metal protectant.
6.
Position knife jig over knife. Loosen gib bolts
until knife is completely loose.
7.
Access jack screws through holes in cutterhead. Using a hex wrench, rotate jack screws
-49to raise or lower knife. When knife is set correctly, it will barely touch middle pad of knife
gib and clean inside cutterhead slot to remove
all pitch or sawdust. Coat knife and gib with a
metal protectant.
6.
Position knife jig over knife. Loosen gib bolts
until knife is completely loose.
7.
Access jack screws through holes in cutterhead. Using a hex wrench, rotate jack screws
Loosen
cutterhead
gibWhen
bolts,knife
starting
in corthe
to
raise or
lower knife.
is set
middle,itand
back
and forth
until
all
rectly,
will alternating
barely touch
middle
pad of
knife
gib or
bolts
are loose,
but not falling
out. of the
jig
bottom
of straightedge
in each
straightedge positions. Snug gib bolts just
The first
timetoyou
or in
replace
knife,
tight
enough
holdset
knife
place. aRepeat
remove
gib andknives.
knife from cutterhead. Clean
with
remaining
gib and clean inside cutterhead slot to remove
all pitch cutterhead
or sawdust. to
Coat
knife the
and first
gib with
a
Rotate
reveal
knife
metal
protectant.
Loosen
cutterhead
gib
bolts,
starting
in
the
you started with. Lightly snug all gib bolts,
middle, andfrom
alternating
backtoand
untiland
all
alternating
one side
theforth
other,
Position
knife
jig over
Loosen
gib
bolts
gib boltsfrom
are loose,
butknife.
notthe
falling
out.
working
the
ends
to
middle.
Repeat
until remaining
knife is completely
with
knives. loose.
The first time you set or replace a knife,
Access
screws
holesalternating
in cutterremove jack
gib
and
from
Clean
Tighten
each
gibknife
boltthrough
in thecutterhead.
same
head.
ainside
hex
rotate
jack
screws
gib
andUsing
clean
cutterhead
slot
to remove
manner
as you
didwrench,
in
the previous
step.
to raise
lower knife.
When
corall
pitch or sawdust.
Coat
knifeknife
and is
gibset
with
a
rectly,
it
will
barely
touch
middle
pad
of
knife
metal
protectant.
Make sure outfeed table is set even with the
jig orknives
bottom
new
at of
topstraightedge
dead center.in each of the
straightedge
Snug
gib bolts
just
Position
knife positions.
jig over knife.
Loosen
gib bolts
tight knife
enough
to holdguard
knife
in place.
Repeat
until
is completely
loose.
Replace
cutterhead
and
cabinet
rear
Figure
70. Jack
screw access hole.
with
remaining
knives.
access
panel.
Access jack screws through holes in cutterRotate
cutterhead
to reveal
thejack
firstscrews
knife
head. Using
a hex wrench,
rotate
you
started
with.knife.
Lightly
snug
all is
gibsetbolts,
to raise
or lower
When
knife
coralternating
one
sidemiddle
to thepad
other,
and
rectly, it willfrom
barely
touch
of knife
working
from the
ends to the middle.
jig or bottom
of straightedge
in eachRepeat
of the
with
remainingpositions.
knives. Snug gib bolts just
straightedge
tight enough to hold knife in place. Repeat
Tighten
each gib
bolt in the same alternating
with remaining
knives.
manner as you did in the previous step.
Rotate cutterhead to reveal the first knife
Make
sure outfeed
table issnug
set even
with
the
you started
with. Lightly
all gib
bolts,
2 to the 4other, and
1 one
3
new knives
at top
dead
center.
alternating
from
side
working from the ends to the middle. Repeat
Figure
71.
Gib knives.
bolt tightening
sequence.
Replace
cutterhead
guard and
cabinet rear
with remaining
access panel.
Tighten each gib bolt in the same alternating
manner as you did in the previous step.
5.
8.
5.
6.
7.
9.
10.
6.
11.
7.
8.
9.
8.
10.
11.
9.
10. Make sure outfeed table is set even with the
new knives at top dead center.
11. Replace cutterhead guard and cabinet rear
access panel.
-50-
Rotating/Replacing
Helical Cutterhead
Inserts (G0814X)
The helical cutterhead is equipped with 4-sided
indexable carbide inserts. Each insert can be
removed, rotated, and re-installed to use any one
of its four cutting edges. Therefore, if one cutting
edge becomes dull or damaged, simply rotate it
90˚ (as shown below) to use a sharp cutting edge.
The inserts have a reference dot on one corner.
The position of the reference dot on installed
inserts can be used to track which edges are
sharp/unused and which edges are dull or damaged. Replace inserts once the reference dot has
been rotated back to its original position.
Reference Dot
Figure 72.
30. Insert rotating sequence.
Item(s) Needed
Qty
Carbide Inserts 15 x 15 x 2.5mm....... As Needed
Flat HD Torx Screws M6-1 x 15............. As Needed
Torque Wrench................................................... 1
T-20 Torx Bit....................................................... 1
To rotate or replace helical cutterhead insert:
1.
DISCONNECT MACHINE FROM POWER!
2.
Remove cutterhead guard from table, and
lower infeed table as far down as it will go.
3.
Remove cover to get access to cutterhead
pulley.
4.
Taking care not to pinch your hand between
belt and pulley, rotate pulley as needed to
make inserts accessible for removal.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
5.
Put on heavy leather gloves to protect fingers
and hands.
6.
Carefully clean away all sawdust or debris
from top of insert, Torx screw, and surrounding area (see Figure below).
Torx
Screw
Cutterhead
Insert
Figure 73. Example of cutterhead inserts and
Torx screws.
7.
Remove Torx screw and insert, then carefully
clean away all dust and debris from insert
and insert pocket in cutterhead.
IMPORTANT: This step is critical for achieving a smooth finish with cutting operations.
Dirt or dust trapped under insert during installation will slightly raise insert in cutterhead,
which will leave marks on workpiece after
jointing.
Setting Outfeed
Table Height
To help ensure safe operation and best cutting
results, set the outfeed table height level with
the knives/inserts when they are at top-deadcenter (TDC). If the outfeed table is set too low,
the workpiece will be tapered from front to back
or there will be snipe (a gouge in the end of the
board that is uneven with the rest of the cut). If the
outfeed table is set too high, the workpiece will hit
the edge of the outfeed table during operation,
increasing the chance of kickback.
Qty
Item(s) Needed
Precision Straightedge 3'................................... 1
To set outfeed table height:
1.
DISCONNECT MACHINE FROM POWER!
2.
Remove cutterhead guard, fence, and
cabinet rear access panel.
3.
G0813/G0814 Only: Make sure knife heights
are set correctly (refer to Setting/Replacing
Knives on Page 48).
4.
Loosen outfeed table lock (see Figure 74).
Tip: Use low-pressure compressed air or a
vacuum nozzle to clean cutterhead pocket.
8.
Re-install insert with a sharp cutting edge
facing outward. Make sure insert is properly
seated in cutterhead pocket before securing.
—If all four insert cutting edges have been
used, replace insert with a new one. Always
position reference dot in same position
when installing a new insert to aid in rotational sequencing.
9.
Lubricate Torx screw threads with a small
amount of light machine oil, wipe excess off,
and torque screw to 48–50 inch/pounds.
Outfeed Table Lock
Infeed Table Lock
Figure 74. Location of table locks.
5.
Place straightedge on outfeed table so it
extends over cutterhead.
IMPORTANT: If too much oil is applied to the
threads, excess will attempt to squeeze out of
threaded hole as you install insert and force it
to raise slightly, making it out of alignment.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
-51-
6.
Use motor pulley to rotate cutterhead until
one knife or insert is at TDC (its highest point
during rotation), as shown in Figures 75–76.
7.
Use outfeed table handwheel to set outfeed
table so knife or insert barely touches straightedge, as shown in Figure 76.
Top Dead
Center
G0813/G0814
G0814X
Figure 75. Knife or insert at TDC.
G0813/G0814
Outfeed
The depth scale can be calibrated or "zeroed" to
make sure the cutting depth shown on the scale
matches the actual cutting depth (per pass).
Before
beginning,
set outfeed
To calibrate
the depth
scale: table height as
described in Setting Outfeed Table Height.
1. Set the outfeed table height as described in
Tools
Needed
Qty
Setting
Outfeed Table Height.
Straightedge....................................................... 1
1
Phillips
Screwdriver
#2.......................................
2. Place
a straightedge
across the infeed and
.
.................................
1
Open-End
Wrench
12mm.
outfeed tables.
Top Dead
Center
Straightedge
Calibrating Depth
Scale
To
depth
scale:
3. calibrate
Adjust the
infeed
table until it is level with the
outfeed table, as shown below.
1. DISCONNECT MACHINE FROM POWER!
4. Using a screwdriver, precisely adjust the
straightedge
2. Place
scale pointer
to “0”.across infeed and outfeed
tables (see Figure 77).
G0813/G0814
Infeed
Straightedge
Outfeed
Straightedge
Outfeed
Bottom Dead
Center
G0814X
Infeed
Figure 76. Using straightedge to check outfeed
table height.
8.
Tighten outfeed table lock so outfeed table
will not move during operation.
9.
Re-install cutterhead guard, fence, and
cabinet rear access panel.
-52-
Infeed
G0814X
Straightedge
Outfeed
Infeed
Figure 77. Infeed table adjusted even with
outfeed table.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
3.
Adjusting Gibs
Loosen jam nut on table stop bolt (see Figure
78) and unthread it several turns.
Screw
Depth
Indicator
Jam Nut
Table Stop Bolt
The function of the table gibs is to eliminate
excessive play in the table movement. The gibs
also control how easy it will be to move the tables
up and down.
Tools Needed
Qty
Open-End Wrench 12mm................................... 1
Hex Wrench 4mm............................................... 1
To adjust table gibs:
1.
Figure 78. Depth indicator set to "0".
4.
5.
Adjust infeed table until it is level with outfeed
table.
Loosen two infeed table gib nuts on front of
jointer base (see Figure 79).
Gib Nut
Using a screwdriver, precisely adjust scale
pointer to “0”, then thread stop bolt into table
and secure with jam nut.
Gib Set Screw
Figure 79. Infeed table gib controls.
2.
Oil table ways and outfeed leadscrew if
needed (see Page 45).
3.
Evenly tighten gib set screws a small amount,
then check table by moving it up and down.
Adjust set screws as needed until friction of
table movement is balanced between minimal play and ease of movement.
Note: Tighter gibs reduce play but make it
harder to adjust tables.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
4.
Repeat Steps 1-3 with outfeed table.
5.
Set outfeed table height as described in
Setting Outfeed Table Height on Page 51.
-53-
Setting Fence Stops
The fence stops simplify the task of adjusting the
fence to 90˚ and 135˚ (45˚ outward).
Setting 135° Fence Stop
1.
Disengage swing stop (see Figure 81).
2.
Use a sliding bevel adjusted to 135˚ to adjust
fence to 135˚ (45˚ outward) position, as
shown in Figure 82.
Tools Needed
Qty
45° Square......................................................... 1
90° Square......................................................... 1
Sliding Bevel....................................................... 1
Open-End Wrench 12mm................................... 1
Setting 90° Fence Stop
1.
Use a 90˚ square to adjust fence to 90˚ (see
Figure 80).
Figure 82. Example of adjusting fence 45˚
outward.
3.
Loosen jam nut on 135˚ stop bolt (see
Figure 83).
Figure 80. Example of adjusting fence to 90˚.
2.
135° Stop Bolt
Flip 90˚ swing stop into position shown in
Figure 81.
Jam Nut
Fence Stop Bolt
Jam Nut
Figure 81. 90˚ swing stop engaged.
3.
Loosen jam nut on 90˚ fence stop bolt (see
Figure 81).
4.
Adjust the 90˚ fence stop bolt until it makes
contact with 90˚ swing stop.
5.
Retighten jam nut loosened in Step 3.
-54-
Figure 83. Location of 135˚ stop bolt and
jam nut.
Swing Stop
4.
Adjust 135˚ stop bolt until it makes contact
with back of fence.
5.
Retighten jam nut loosened in Step 3.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
Tensioning/
Replacing V-Belt
To ensure optimum power transmission from
the motor to the cutterhead, the V-belt must be
in good condition (free from cracks, fraying and
wear) and properly tensioned.
Belts and pulleys will be hot after operation.
Allow them to cool before handling.
5. Press belt with moderate pressure in center to check belt tension. Belt is correctly
tensioned when there is approximately 1⁄4"
deflection when pushed, as shown in Figure
85.
— If there is more than 1⁄4" deflection when
you check belt tension, repeat the tensioning procedure until it is correct.
After approximately 16 hours of operation, belts will stretch and seat into pulley grooves. The belts need to be re-tensioned after this initial break-in period
to ensure optimum power transfer and
maximum overall life of the belts.
Cutterhead Pulley
Approximately
1
/4" Deflection
Item(s) Needed
Qty
Phillips Screwdriver #2....................................... 1
Open-End or Socket Wrench 12mm.................. 1
Motor Pulley
Tensioning Belt
1.
DISCONNECT MACHINE FROM POWER!
2.
Remove cabinet rear access panel.
Figure 85. Correct belt deflection when properly
tensioned.
3.
Loosen motor mount fasteners shown in
Figure 84. DO NOT completely remove
motor mount fasteners.
6.
Tighten motor mount fasteners (see
Figure 84) and replace cabinet rear access
panel.
Replacing Belt
Motor
Mount
Fasteners
(2 of 4)
1.
DISCONNECT MACHINE FROM POWER!
2.
Remove cabinet rear access panel and belt
guard.
3.
Loosen motor mount fasteners shown in
Figure 84.
4.
Have another person lift motor as you remove
belt and replace it with a new one. Make sure
ribs of belt are seated in pulley grooves.
5.
Follow Steps 4–5 in Tensioning Belt procedure to set correct belt tension.
6.
Tighten motor mount fasteners (see Figure
84), and replace cabinet rear access panel
and belt guard.
Figure 84. Motor mounting fasteners location.
4.
Press down on motor to keep tension on belt.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
-55-
Aligning Pulleys
Pulley alignment is another important factor in
power transmission and belt life. The pulleys
should be parallel to each other and in the same
plane (coplaner) for optimum performance.
Straightedge
The pulleys can be adjusted by loosening the
pulley set screws, aligning the pulleys, and
retightening the set screws.
Tool Needed
Qty
Hex Wrench 3mm............................................... 2
Straightedge....................................................... 1
Cutterhead
Pulley
Alignment
To align pulleys:
1.
DISCONNECT MACHINE FROM POWER!
2.
Remove cabinet rear access panel and belt
guard.
3.
Place straightedge against pulleys to check
their alignment (see Figure 86).
Motor
Pulley
Figure 86. Checking pulley alignment.
— If they are not aligned, loosen set screws
on cutterhead or motor pulley as needed
to align pulleys, then tighten set screws
(see Figure 87).
Note: This can also be done visually (without
a straightedge) if you do not have a straightedge available that will fit; however, the
most accurate results will come from using a
straightedge.
Pulley
x2
Figure 87. Motor pulley set screw locations.
4.
-56-
Replace cabinet rear access panel and belt
guard.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
Checking/Adjusting
Table Parallelism
5.
—If there are no gaps, and the straightedge
makes full contact with both tables at front
and rear, the tables are parallel with each
other and no adjustments are necessary.
The infeed and outfeed tables must be parallel
with each other in order to produce a straight,
jointed edge. When the tables are not parallel
with each other, the jointer will produce workpieces that are cupped (concave) or bowed (convex)
along their length.
Table parallelism is factory-set, and should not
normally need to be adjusted when the machine
is new. However, after prolonged use, or if
machine has been jarred during lifting or transportation, it may become necessary to adjust the
table parallelism.
—If there are gaps anywhere between one of
the tables and the straightedge, the tables
are not parallel to each other and must be
adjusted. Proceed to Step 6.
6.
Table parallelism is adjusted by inserting shims
between the dovetailed ways of the outfeed table
to make it parallel with the infeed table. Once
this adjustment is made, the outfeed table height
should not need to be adjusted again.
Items Needed
Qty
Straightedge 4–8'............................................... 1
Feeler Gauge Set............................................... 1
Metal Shims........................................ As Needed
Look down length of straightedge on outfeed
side to see if there are any noticeable gaps
between straightedge and outfeed table. Do
this at both front and rear of table.
Insert feeler gauge between table and
straightedge where gap is greatest (see
Figure). Maximum allowable tolerance is
0.003".
Insert Feeler Gauge
Where Gap is Greatest
Outfeed
Straightedge
Infeed
Figure 89. Example of feeler gauge location for
checking table parallelism.
To check/adjust table parallelism:
1.
DISCONNECT MACHINE FROM POWER!
2.
Move cutterhead guard out of the way.
3.
Set outfeed table height as described in
Setting Outfeed Table Height.
4.
7.
Possible Shim
Locations
Rotate cutterhead until knife/insert is no longer at TDC, extend straightedge over both
tables, raise infeed table until it contacts
straightedge (see Figure), then lock infeed
table.
Figure 90. Typical locations to place shims when
adjusting table parallelism.
Straightedge
Outfeed
Loosen outfeed table lock(s). Place shims
between dovetailed ways, as shown, until
outfeed table is within 0.003" of parallel with
infeed table at front and rear of tables.
Infeed
8.
Re-check outfeed table height (refer to
Setting Outfeed Table Height), and re-adjust if necessary.
Figure 88. Checking table parallelism.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
-57-
machine
SECTION 8: WIRING
These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Compare the manufacture date of your machine to the one
stated in this manual, and study this section carefully.
If there are differences between your machine and what is shown in this section, call Technical Support at
(570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine. An updated
wiring diagram may be available. Note: Please gather the serial number and manufacture date of your
machine before calling. This information can be found on the main machine label.
Wiring Safety Instructions
SHOCK HAZARD. Working on wiring that is connected to a power source is extremely dangerous.
Touching electrified parts will result in personal
injury including but not limited to severe burns,
electrocution, or death. Disconnect the power
from the machine before servicing electrical components!
MODIFICATIONS. Modifying the wiring beyond
what is shown in the diagram may lead to unpredictable results, including serious injury or fire.
This includes the installation of unapproved aftermarket parts.
WIRE CONNECTIONS. All connections must
be tight to prevent wires from loosening during
machine operation. Double-check all wires disconnected or connected during any wiring task to
ensure tight connections.
CIRCUIT REQUIREMENTS. You MUST follow
the requirements at the beginning of this manual
when connecting your machine to a power source.
WIRE/COMPONENT DAMAGE. Damaged wires
or components increase the risk of serious personal injury, fire, or machine damage. If you notice
that any wires or components are damaged while
performing a wiring task, replace those wires or
components.
MOTOR WIRING. The motor wiring shown in
these diagrams is current at the time of printing
but may not match your machine. If you find this
to be the case, use the wiring diagram inside the
motor junction box.
CAPACITORS/INVERTERS. Some capacitors
and power inverters store an electrical charge for
up to 10 minutes after being disconnected from
the power source. To reduce the risk of being
shocked, wait at least this long before working on
capacitors.
EXPERIENCING DIFFICULTIES. If you are experiencing difficulties understanding the information
included in this section, contact our Technical
Support at (570) 546-9663.
The photos and diagrams
included in this section are
best viewed in color. You
can view these pages in
color at www.grizzly.com.
-58-
Model G0813/G0814/G0814X (Mfd. Since 10/19)
110V Wiring Diagram
Neutral
Hot
110 VAC
5-15 Plug
Ground
ON/OFF Switch
(Viewed from Behind)
KEDU
HY-18
20/12A
125/250V
GND
GND
Figure 92. ON/OFF switch wiring
(viewed from behind).
Ground
MOTOR
Motor Junction Box
Start Capacitor
Figure 91. Motor junction box.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
300MFD
125VAC
READ ELECTRICAL SAFETY
ON PAGE 58!
-59-
220V Wiring Diagram
Hot
Hot
G
220VAC
6-15 Plug
Ground
ON/OFF Switch
(Viewed from Behind)
KEDU
HY-18
20/12A
125/250V
GND
GND
Indicates wiring
changes for
220V conversion
Ground
MOTOR
Figure 93. ON/OFF switch wiring
(viewed from behind).
-60-
READ ELECTRICAL SAFETY
ON PAGE 58!
Motor Junction Box
Start Capacitor
300MFD
125VAC
Model G0813/G0814/G0814X (Mfd. Since 10/19)
SECTION 9: PARTS
We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown
are available for purchase. Call (800) 523-4777 or visit www.grizzly.com/parts to check for availability.
Table
33
32
29
30
3
30
34
42
8
58
9
40
11
18
36
10
41
31
14
25
16
12
43
43
6
15
19
51
49
52
27
7
2
1
5
60
60
35
28 26
60
59
53
39
54
4
57
61
23
20
22
24
56
55
Model G0813/G0814/G0814X (Mfd. Since 10/19)
21
13
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
-61-
Table Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
19
20
21
22
23
24
25
26
27
TABLE BASE
INFEED TABLE
OUTFEED TABLE
GIB
TABLE LOCK HANDLE M8-1.25 X 30
SET SCREW M8-1.25 X 25
HEX NUT M8-1.25
PIVOT SHAFT 19 X 178MM
HANDWHEEL TYPE-21 123D X 20-B X 5/16-18
SET SCREW 1/4-20 X 1/4
OUTFEED TABLE ADJUST BLOCK
OUTFEED TABLE LEADSCREW
HANDLE 1/2-12, 1-1/2 X 2-1/2 (PLASTIC)
BELT GUARD
FLAT WASHER 5/16
LEADSCREW BRACKET
CUTTERHEAD GUARD
GUARD SHAFT
SPRING PLATE
TORSION SPRING
GUARD TENSION KNOB
GUARD MOUNT COLLAR
PHLP HD SCR 8-32 X 5/8
CAP SCREW 5/16-18 X 1
DEPTH-OF-CUT SCALE
POINTER
28
29
30
31
32
33
34
35
36
39
40
41
42
43
49
51
52
53
54
55
56
57
58
59
60
61
NAMEPLATE RIVET 2 X 5
CARRIAGE SUPPORT
HEX BOLT 3/8-16 X 1-1/4
FLAT WASHER 3/8
KEY 3/8 X 3/8 X 9
ROLL PIN 4 X 12
FLAT WASHER 3/8
PHLP HD SCR 8-32 X 1/4
HEX BOLT 5/16-18 X 2-1/2
ADJ HANDLE 89MM, M8-1.25 X 45
FLAT WASHER 5/16
FLAT WASHER #10
PHLP HD SCR 10-24 X 3/8
FLAT WASHER 1/2
SET SCREW M5-.8 X 8
HEX BOLT 1/4-20 X 1/2
FLAT WASHER 1/4
BASE ROD 12.5 X 180MM
INFEED TABLE ADJUST BLOCK
STUD-UDE 1/2-12 X 15-3/4, 3/4, 1-3/8
HEX BOLT 5/16-18 X 1-3/4
HEX NUT 5/16-18
REVOLVING HANDLE 5/16-18, 3/4 X 3-1/4
PIVOT SHAFT 12.5 X 180MM
E-CLIP 12MM
HEX NUT 1/2-12
-62-
P0813001
P0813002
P0813003
P0813004
P0813005
P0813006
P0813007
P0813008
P0813009
P0813010
P0813011
P0813012
P0813013
P0813014
P0813015
P0813016
P0813018
P0813019
P0813020
P0813021
P0813022
P0813023
P0813024
P0813025
P0813026
P0813027
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
P0813028
P0813029
P0813030
P0813031
P0813032
P0813033
P0813034
P0813035
P0813036
P0813039
P0813040
P0813041
P0813042
P0813043
P0813049
P0813051
P0813052
P0813053
P0813054
P0813055
P0813056
P0813057
P0813058
P0813059
P0813060
P0813061
Model G0813/G0814/G0814X (Mfd. Since 10/19)
Fence
129
130
128
125
123
123
122
117
101
104
105
121
118 133
113
119
112
102
114
115
116
124
120
111
102
110
132
108
103
126
109
126
127
106
131
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
101
102
103
104
105
106
108
109
110
111
112
113
114
115
116
117
FENCE
PIVOT STUD 1/2-20 X 5/8
FENCE HINGE
SET SCREW 3/8-16 X 1-1/2 CONE-PT
HEX NUT 3/8-16
TILT LEVER 3/8-16 X 1/2
FLAT HD CAP SCR 5/16-18 X 1-5/8
FENCE BRACKET
FENCE STOP BRACKET
SHOULDER BOLT 5/16-18 X 112, 3/8 X 3/4
HEX NUT 7/16-14
STANDOFF STUD 7/16-14 X 1-1/4, 5/8-18, 6-1/2L
FENCE TILT CLAMP
STOP TAB-90 DEG
ROLL PIN 4 X 12
SHOULDER BOLT 5/16-18 X 3/8, 1/4 X 3/8
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
SWING STOP
HEX NUT 5/8-18
FENCE TILT BUSHING
FENCE CARRIAGE
FLAT WASHER 1/2
FENCE LOCK 1/2-13 X 1-1/8
FENCE TILT LOCK NUT 1/2-12
HEX BOLT 5/16-18 X 1
HEX NUT 5/16-18
HEX BOLT 5/16-18 X 1-3/4
FENCE LOCK BRACKET
PHLP HD SCR 1/4-20 X 1/2
FLAT WASHER 1/4
SUPPORT PIN 1/4 X 1/2 (PLASTIC)
HEX NUT 1/2-20
FLAT WASHER 1/2
P0813101
P0813102
P0813103
P0813104
P0813105
P0813106
P0813108
P0813109
P0813110
P0813111
P0813112
P0813113
P0813114
P0813115
P0813116
P0813117
Model G0813/G0814/G0814X (Mfd. Since 10/19)
P0813118
P0813119
P0813120
P0813121
P0813122
P0813123
P0813124
P0813125
P0813126
P0813127
P0813128
P0813129
P0813130
P0813131
P0813132
P0813133
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
-63-
Cutterhead
215
202
213
G0813/
G0814
Only
204
205
212
214
211
208
209
210
201
207
206
217
G0814X
Only
219
218
208
221
201
207
202
206
218
222
220
219
203
218A
(G0813/G0814 Only)
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
201
201
202
202
203
204
205
206
207
208
209
210
CUTTERHEAD 6" 3-KNIFE (G0813/G0814)
CUTTERHEAD 6" V-HELICAL (G0814X)
KNIFE 6" X 1" X 1/8" 3-PC
INDEXABLE INSERT 15 X 15 X 2.5MM
FLAT HD TORX SCR T20 M6-1 X 15
KNIFE GIB
GIB BOLT 1/4-20 X 1/4 W/8MM HEAD
HEX NUT 3/8-24
LOCK WASHER 3/8
STUD-SE 3/18-16 X 3-1/2, 3/4"
BEARING BLOCK (LEFT)
BALL BEARING 6202-2RS
211
212
213
214
215
217
218A
218
219
220
221
222
KEY 5 X 5 X 30
BALL BEARING 6203-2RS
BEARING BLOCK (RIGHT)
CUTTERHEAD PULLEY
SET SCREW 1/4-20 X 3/8
FLAT HD CAP SCR M5-.8 X 12
KNIFE-SETTING JIG
KNIFE-SETTING JIG FOOT
E-CLIP 9MM
KNIFE-SETTING JIG SHAFT
T-HANDLE TORX DRIVER 1/4"
T-20 TORX BIT
-64-
P0813201
P0814X201
P0813202
P0814X202
P0814X203
P0813204
P0813205
P0813206
P0813207
P0813208
P0813209
P0813210
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
P0813211
P0813212
P0813213
P0813214
P0813215
P0813217
P0813218A
P0813218
P0813219
P0813220
P0814X221
P0814X222
Model G0813/G0814/G0814X (Mfd. Since 10/19)
G0813 Stand
304
334
301
330
391
326
330
316 311
315
305 389
314
303
335
316
330
308
313
330
322
310
321
317
306
327
307 328
329
326
318
312
335
316
320
311
310
319
302
338
339
385
379
385
341
384
366 365
325
316
393
375
340
367
387
330
350 375
386
390
382
381
380
374
361
366
368
377
367
320-2
320-3
320-4
362
369
376
363
377
364 371
370
371
377
378
320-1
376
372
373
379
350
375
360A
320-9
320-8
320-5
320-7
320-6
320-10
371
383
374
372
Model G0813/G0814/G0814X (Mfd. Since 10/19)
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
-65-
G0813 Stand Parts List
REF
PART #
DESCRIPTION
REF PART #
DESCRIPTION
301
302
303
304
305
306
307
308
310
311
312
313
314
315
316
317
318
319
320
320-1
320-2
320-3
320-4
320-5
320-6
320-7
320-8
320-9
320-10
321
322
325
326
327
328
329
330
334
P0813301
P0813302
P0813303
P0813304
P0813305
P0813306
P0813307
P0813308
P0813310
P0813311
P0813312
P0813313
P0813314
P0813315
P0813316
P0813317
P0813318
P0813319
P0813320
P0813320-1
P0813320-2
P0813320-3
P0813320-4
P0813320-5
P0813320-6
P0813320-7
P0813320-8
P0813320-9
P0813320-10
P0813321
P0813322
P0813325
P0813326
P0813327
P0813328
P0813329
P0813330
P0813334
TOP PLATE
RIGHT PANEL
LEFT PANEL
LEFT CHUTE SUPPORT
RIGHT CHUTE SUPPORT
MOTOR MOUNT PLATE
FRONT PANEL
SWITCH COVER
CORNER SUPPORT A
CORNER SUPPORT B
HEX NUT 5/16-18
FLAT WASHER 5/16
CARRIAGE BOLT 5/16-18 X 5/8
HEX BOLT 3/8-16 X 3/4
FLAT WASHER 3/8
MOTOR PULLEY
SET SCREW 1/4-20 X 3/8
V-BELT A36
MOTOR 1HP 110V/220V 1-PH
MOTOR FAN COVER
MOTOR FAN
CAPACITOR COVER
MOTOR JUNCTION BOX
S CAPACITOR 300M 125V 1-3/4 X 3-3/8
BALL BEARING (FRONT)
BALL BEARING (REAR)
CONTACT PLATE
CENTRIFUGAL SWITCH
STRAIN RELIEF TYPE-2 M8-1.25
KEY 5 X 5 X 30
PADDLE SWITCH KEDU HY-18
POWER CORD 16G 3W 72" 5-15P
STRAIN RELIEF 5/8" TYPE-1 SNAP-IN SB6R-3
FLANGE SCREW 10-24 X 3/8
EXT TOOTH WASHER #10
HEX NUT 10-24
FLANGE SCREW 10-24 X 3/8
DUST PORT 4"
335
338
339
340
341
350
360A
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
389
390
391
393
HEX NUT 3/8-16
WRENCH 8 X 10MM OPEN-ENDS
WRENCH 12 X 14MM OPEN-ENDS
HEX WRENCH 3MM
PUSH BLOCK
WHEEL
FOOT PEDAL ASSEMBLY
PEDAL
PEDAL BRACKET
TROLLEY BRACKET (UPPER)
TROLLEY BRACKET (LOWER)
CLEVIS PIN, HEADLESS-GROOVED
FLAT WASHER 13 X 27 X 3MM
E-CLIP 12MM
HEX BOLT 5/16-18 X 2
FLAT WASHER 5/16
HEX BOLT 5/16-18 X 4
FLAT WASHER 5/16
LOCK NUT 5/16-18
HEX BOLT 5/16-18 X 2-1/2
BUSHING
FLAT WASHER 5/16 (PLASTIC)
HEX BOLT 3/8-16 X 2-1/2
FLAT WASHER 3/8
HEX NUT 3/8-16
BALL BEARING 6001ZZ
LEVELING FOOT 3/18-16 X 2
FLAT WASHER 3/8
HEX NUT 3/8-16
HEX BOLT 5/16-18 X 3/8
HEX BOLT 3/8-16 X 2-1/2
FLAT WASHER 3/8
LOCK NUT 3/8-16
MOBILE BASE CHASSIS
HEX NUT 10-24
MOTOR CORD 16G 3W 31"
REAR PANEL
HEX BOLT 3/8-16 X 1
-66-
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
P0813335
P0813338
P0813339
P0813340
P0813341
P0813350
P0813360A
P0813361
P0813362
P0813363
P0813364
P0813365
P0813366
P0813367
P0813368
P0813369
P0813370
P0813371
P0813372
P0813373
P0813374
P0813375
P0813376
P0813377
P0813378
P0813379
P0813380
P0813381
P0813382
P0813383
P0813384
P0813385
P0813386
P0813387
P0813389
P0813390
P0813391
P0813393
Model G0813/G0814/G0814X (Mfd. Since 10/19)
G0814/G0814X Stand
331
333
333
332
334
328
326
327
308
316
329
322
315
393
326
325
375
390
350
375
385
385
384
374
382
381
380
386
379
312
313
306
321
339
338
340
319
341
317
314
320
318
367
366 365
361
366
368
377
367
369
376
362
376
363
377
364 371
370
371
377
378
320-1
372
373
379
350
360A
375
371
383
374
372
Model G0813/G0814/G0814X (Mfd. Since 10/19)
320-3
320-2
320-4
320-5
320-9
320-8
320-7
320-6
320-10
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
-67-
G0814/G0814X Stand Parts List
REF
PART #
DESCRIPTION
REF PART #
DESCRIPTION
306
308
312
313
314
315
316
317
318
319
320
320-1
320-2
320-3
320-4
320-5
320-6
320-7
320-8
320-9
320-10
321
322
325
326
327
328
329
331
332
333
334
338
P0814306
P0814308
P0814312
P0814313
P0814314
P0814315
P0814316
P0814317
P0814318
P0814319
P0814320
P0814320-1
P0814320-2
P0814320-3
P0814320-4
P0814320-5
P0814320-6
P0814320-7
P0814320-8
P0814320-9
P0814320-10
P0814321
P0814322
P0814325
P0814326
P0814327
P0814328
P0814329
P0814331
P0814332
P0814333
P0814334
P0814338
MOTOR MOUNT PLATE
SWITCH COVER
HEX NUT 5/16-18
FLAT WASHER 5/16
CARRIAGE BOLT 5/16-18 X 5/8
HEX BOLT 3/8-16 X 3/4
FLAT WASHER 3/8
MOTOR PULLEY
SET SCREW 1/4-20 X 3/8
V-BELT A36
MOTOR 1HP 110V/220V 1-PH
MOTOR FAN COVER
MOTOR FAN
CAPACITOR COVER
MOTOR JUNCTION BOX
S CAPACITOR 300M 125V 1-3/4 X 3-3/8
BALL BEARING (FRONT)
BALL BEARING (REAR)
CONTACT PLATE
CENTRIFUGAL SWITCH
STRAIN RELIEF TYPE-2 M8-1.25
KEY 5 X 5 X 30
PADDLE SWITCH KEDU HY-18
POWER CORD 16G 3W 72" 5-15P
STRAIN RELIEF 5/8" TYPE-1 SNAP-IN SB6R-3
FLANGE SCREW 10-24 X 3/8
EXT TOOTH WASHER #10
HEX NUT 10-24
STAND
CABINET DOOR
FLANGE SCREW 10-24 X 3/8
DUST PORT 4"
WRENCH 8 X 10MM OPEN-ENDS
339
340
341
350
360A
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
390
393
WRENCH 12 X 14MM OPEN-ENDS
HEX WRENCH 3MM
PUSH BLOCK
WHEEL
FOOT PEDAL ASSEMBLY
PEDAL
PEDAL BRACKET
TROLLEY BRACKET (UPPER)
TROLLEY BRACKET (LOWER)
CLEVIS PIN, HEADLESS-GROOVED
FLAT WASHER 13 X 27 X 3MM
E-CLIP 12MM
HEX BOLT 5/16-18 X 2
FLAT WASHER 5/16
HEX BOLT 5/16-18 X 4
FLAT WASHER 5/16
LOCK NUT 5/16-18
HEX BOLT 5/16-18 X 2-1/2
BUSHING
FLAT WASHER 5/16 (PLASTIC)
HEX BOLT 3/8-16 X 2-1/2
FLAT WASHER 3/8
HEX NUT 3/8-16
BALL BEARING 6001ZZ
LEVELING FOOT 3/18-16 X 2
FLAT WASHER 3/8
HEX NUT 3/8-16
HEX BOLT 5/16-18 X 3/8
HEX BOLT 3/8-16 X 2-1/2
FLAT WASHER 3/8
LOCK NUT 3/8-16
MOTOR CORD 16G 3W 31"
TAP SCREW #5 X 3/8
-68-
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
P0814339
P0814340
P0814341
P0814350
P0814360A
P0814361
P0814362
P0814363
P0814364
P0814365
P0814366
P0814367
P0814368
P0814369
P0814370
P0814371
P0814372
P0814373
P0814374
P0814375
P0814376
P0814377
P0814378
P0814379
P0814380
P0814381
P0814382
P0814383
P0814384
P0814385
P0814386
P0814390
P0814393
Model G0813/G0814/G0814X (Mfd. Since 10/19)
G0813 Labels & Cosmetics
401
402
409
408
403
407
404
406
405
403
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
401
402
403
404
405
CUTTERHEAD EXPOSURE WARNING LABEL
CUTTERHEAD WARNING LABEL
ELECTRICITY LABEL
MACHINE ID LABEL
GRIZZLY.COM LABEL
406
407
408
409
MODEL NUMBER LABEL
TOUCH-UP PAINT, GRIZZLY BEIGE
COMBINED WARNING LABEL
TOUCH-UP PAINT, GRIZZLY GREEN
P0813401
P0813402
P0813403
P0813404
P0813405
P0813406
P0813407
P0813408
P0813409
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
-69-
(10/23/15)
WARNING!
Failure to keep hands clear
of cutterhead will result in
serious personal injury.
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
WARNING!
G0814/G0814X Labels & Cosmetics
DANGER!
• Scale: 1:1 (Labels are
ROTATING
CUTTERHEAD BELOW!
actual size)
• Labels must be made of
oil-resistant material
DANGER!
G0814 Machine Labels (B)
(10/23/15)
402
Failure to keep hands clear
of cutterhead will result in
serious personal injury.
ROTATING
CUTTERHEAD BELOW!
Do not operate machine
with guard removed!
Cutterhead contact will
cause serious personal
WARNING!
3.
Ensure outfeed table is
even with knives.
Never exceed the
maximum depth of cut.
Do not stand directly
(10/23/15)
Push blocks minimize the
SRVVLELOLW\RIRSHUDWRU·V
hands contacting the
Cutterhead
exposed between
service.
this machine.
ROTATING
CUTTERHEAD BELOW!
ROTATING
CUTTERHEAD
BELOW!
Specifications
KICKBACK HAZARD!
Specifications
1 HP,
110V/220V,
1-Ph, 60 Hz
1. Ensure Motor:
outfeed
table
is even with
KICKBACK
HAZARD!
knives. Full-Load Amp Draw: 14A
Cutterhead:
3-Knife,
2-1/2"
Dia.
Motor:
1 HP,
110V/220V,
1-Ph,
1. Ensure
outfeed
table
is even
2. Never
exceed
maximum
depthwith
of cut.60 Hz
Knife Size:
6" x
1" x 1/8"
Full-Load
Amp
Draw:
14A
3. Do not
stand
directly
knives.
Maximum
Depthbehind
of Cut:workpiece.
1/8"
Cutterhead:
3-Knife,
2-1/2"
Dia.
Maximum
Rabbeting
Depth:
2. Never exceed
maximum
depth
of1/2"
cut.
Knife
Size: 6"Speed:
x 1" x5000
1/8"RPM
Cutterhead
3. Do not stand
directly
Maximum
Depthbehind
of Cut:workpiece.
1/8"
Cuts Per Minute: 15,000
Fence Tilt:
45º, 90º, 135º
Maximum
Rabbeting
Depth: 1/2"
ALWAYS
USE
PUSH
BLOCKS!
Table Size:Speed:
47" x 7-1/4"
Cutterhead
5000 RPM
Weight:
245 lbs.
Push blocks
minimize
possibility of
Cuts Per Minute: 15,000
RSHUDWRU·VKDQGVFRQWDFWLQJFXWWHUKHDG
Fence Tilt: 45º, 90º, 135º
ALWAYS
USE PUSH BLOCKS!
while cutting.
Table Size: 47" x 7-1/4"
Weight:
245 lbs.
Push blocks
minimize
possibility of
operator’s hands contacting
cutterhead
Date
while cutting.
S/N
Mfd. for Grizzly in Taiwan
410
KICKBACK HAZARD!
Cutterhead
exposed between
these lines.
Use this guard for all operations
possible, and immediately re-install it
following operations that require its
removal.
1. Ensure outfeed table is even with
knives.
KICKBACK HAZARD!
2. Never exceed maximum depth of cut.
1. Ensure outfeed table is even with
knives. 3. Do not stand directly behind workpiece.
2. Never exceed maximum depth of cut.
3. Do not stand directly behind workpiece.
ALWAYS USE PUSH BLOCKS!
ALWAYS
USEblocks
PUSH BLOCKS!
Push
minimize possibility of
Push blocksoperator’s
minimize possibility
of
hands contacting
cutterhead
RSHUDWRU·VKDQGVFRQWDFWLQJFXWWHUKHDG
while cutting.
while cutting.
WARNING!
DANGER
WARNING!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
"
go to www.grizzly.com.
To reduce risk of short
WARNING
PANTONE 151 C or RAL 2005
CAUTION
PANTONE 109 C
Specifications
405 WARNING!
WARNING!
go to www.grizzly.com.
MODEL G0814
JOINTER w/CABINET STAND
6" WARNING!
WARNING!
G0814
406
clothing,
gloves,
or jewelry.
12. Always feed workpiece
against
cutterhead
rotation. Never move
WARNING!
9. Turn
motor
OFF and disconnect power before changing inserts,
backward
while
feeding.
MODEL
G0814X 13. workpiece
Prevent unauthorized
use by children
or untrained
users; restrict
adjusting
tables/fence,
or servicing.
machine starting,
when unattended.
10. Before
ensure tables are adjusted properly, blades are
6" JOINTER w/STAND &access or disable
secure, and jointer is stable.
11.
Always
support
workpiece against fence and table. Never attempt
V-HELICAL CUTTERHEAD
any operation free-handed.
G0814
Cutterhead: V-Helical w/Indexable Inserts
Insert Size: 15 x 15 x 2.5mm
10.
Number of Inserts: 24
11.
Maximum Depth of Cut: 1/8"
Date
Maximum Rabbeting
Depth: 1/2"
12.
Cutterhead Speed: 5000 RPM
S/N
Cuts Per Minute: 20,000
13.
Fence
Tilt:
45º,
90º, 135º
in Taiwan
Grizzly
Mfd. for
Table Size: 47" x 7-1/4"
Weight: 245 lbs.
Except when rabbeting, keep all guards in place and in proper
operating condition. Always replace guard after rabbeting.
Date
Never cut workpieces smaller than 8" long, 3/4" wide, or 1/2" thick.
Always use push blocks when face planing.
Never cut deeper than 1/8" on a single pass.
S/N
Tie
longthe
hair,risk
roll up
sleeves, and
DO NOT
wear
loosethis machine:
Toback
reduce
of serious
injury
when
using
clothing, gloves, or jewelry.
1. Read & understand owner’s
Taiwan operating.
Grizzly inbefore
Mfd. formanual
Turn motor OFF and disconnect power
before
changing
inserts,
2. Always
wear approved
eye protection and respirator.
adjusting
tables/fence,
or servicing.
3. Only
plugensure
power
cordare
into
a grounded
Before
starting,
tables
adjusted
properly,outlet.
blades are
secure,
and jointer
is rabbeting,
stable.
4. Except
when
keep all guards in place and in proper
Always
support workpiece
against
fencereplace
and table.
Neverafter
attempt
operating
condition.
Always
guard
rabbeting.
any operation free-handed.
5. Never cut workpieces smaller than 8" long, 3/4" wide, or 1/2" thick.
Always feed workpiece against cutterhead rotation. Never move
6. Always
use push
workpiece
backward
while blocks
feeding. when face planing.
7. Never
cut deeper
than
1/8" on
a singleusers;
pass.restrict
Prevent
unauthorized
use by
children
or untrained
access
or back
disable
machine
unattended.
8. Tie
long
hair,when
roll up
sleeves, and DO NOT wear loose
WARNING!
KICKBACK HAZARD!
Date
S/N
Mfd. for Grizzly in Taiwan
RSHUDWRU·VKDQGVFRQWDFWLQJFXWWHUKHDG
while cutting.
clothing, gloves, or jewelry.
9. Turn motor OFF and disconnect power before changing inserts,
adjusting tables/fence, or servicing.
10. Before starting, ensure tables are adjusted properly, blades are
secure, and jointer is stable.
11. Always support workpiece against fence and table. Never attempt
any operation free-handed.
12. Always feed workpiece against cutterhead rotation. Never move
workpiece backward while feeding.
13. Prevent unauthorized use by children or untrained users; restrict
access or disable machine when unattended.
407
G0814X
ALWAYS USE PUSH B
Push blocks minimize poss
operator’s hands contactin
while cutting.
404
COLOR CODES
Rear View
DANGER
PANTONE 485 C or RAL 3001
WARNING
PANTONE 151 C or RAL 2005
CAUTION
PANTONE 109 C
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
401
402
403
404
405
405
406
CUTTERHEAD EXPOSURE WARNING LABEL
CUTTERHEAD WARNING LABEL
EYE/EAR/LUNG WARNING LABEL
ELECTRICITY LABEL
MODEL NUMBER LABEL (G0814)
MODEL NUMBER LABEL (G0814X)
GRIZZLY NAMEPLATE-SMALL
407
408
409
410
410
411
412
GRIZZLY.COM LABEL Rear View
TOUCH-UP PAINT, GRIZZLY GREEN
TOUCH-UP PAINT, GRIZZLY BEIGE
MACHINE ID LABEL (G0814)
MACHINE ID LABEL (G0814X)
DISCONNECT POWER LABEL
READ MANUAL LABEL
P0814401
P0814402
P0814403
P0814404
P0814405
P0814X405
P0814406
P0814407
P0814408
P0814409
P0814410
P0814X410
P0814411
P0814412
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.
-70-
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
KICKBACK HAZA
1. Ensure outfeed table is e
knives.
2. Never exceed maximum d
ALWAYS USE PUSH BLOCKS!
Push blocks minimize possibility of3. Do not stand directly beh
408
G0814
G0814X
possible, and immediately r
following operations that re
removal.
1. Ensure outfeed table is even with
knives.
2. Never exceed maximum depth of cut.
3. Do not stand directly behind workpiece.
12. Always feed workpiece against cutterhead rotation. Never move
workpiece backward while feeding.
13. Prevent unauthorized use by children or untrained users; restrict
access or disable machine when unattended.
G0814
INJUR
HA
Disconn
before aC
DANGER
maintena
service.
WARNING
Use this guard for all operations
possible, and immediately re-install it
following operations that require its ROTATING CUTTERHEA
removal.
Use this guard for all opera
1. Read & understand owner’s
Taiwan operating.
Grizzly inbefore
Mfd. formanual
2. Always wear approved eye protection and respirator.
Specifications
To reduce risk ofHAZARD!
short
power
Disconnect
and long-term
injury,
COLOR CODES
adjustments,
wear safetybefore
glasses,
DANGER
PANTONE 485 C or RAL 3001
maintenance,
hearing protection,
and or
service.
WARNING
PANTONE 151 C or RAL 2005
a respirator when
using
this machine.CAUTION PANTONE 109 C
ROTATING CUTTERHEAD BELOW!
using this machine:
CAUTION
109 C
Insert Size: 15 x 15 xPANTONE
2.5mm
3. Only plug power cord into a grounded outlet.
Number of Inserts: 24
4.
Maximum Depth of Cut: 1/8"
Maximum Rabbeting Depth: 1/2"
5.
Cutterhead Speed: 5000 RPM
6.
Cuts Per Minute: 20,000
7.
Fence
Tilt: 45º,
90º, 135º 1-Ph, 60 Hz
8.
Motor:
1 HP,
110V/220V,
Table Size: 47" x 7-1/4"
Full-Load Current: 14A at 110V, 7A at 220V
Weight: 245 lbs.
9.
INJURY/SHOCK
INJURY HAZARD!
access or disable machine when unattended.
CAUTION
409
S/N
WARNING
PANTONE 151 ToCreduce
or RAL
2005
Motor: 1 HP, 110V/220V, 1-Ph, 60 Hz
the risk of serious injury when using this machine:
Full-Load Current: 14A at 110V, 7A at 220V
Cutterhead: V-Helical w/Indexable Inserts
WARNING!
G0814
G0814
G0814X
G0814X
9. Turn motor OFF and disconnect power before changing inserts,
MODEL G0814X
Cutterhead Speed: 5000 RPM adjusting tables/fence,
5. Never
workpieces smaller than 8" long, 3/4" wide, or 1/2" thick.
or cut
servicing.
COLOR CODES
Cuts Per Minute:&
15,000
10. Before starting,6.ensure
tables
arepush
adjusted
properly,
blades
Always
use
blocks
when
faceare
planing.
6" JOINTER w/STAND
secure, and jointer
is stable.
CAUTION
PANTONE 109 C
Fence Tilt: 45º, 90º, 135º
7. Never
cut deeper than 1/8" on a single pass.
11. Always support workpiece against fence and table. Never attempt
CUTTERHEAD
Table Size: 47" x 7-1/4"
8. Tie back long hair, roll up sleeves, and DO NOT wear loose
DANGER
PANTONE 485 C orV-HELICAL
RAL 3001
any operation free-handed.
Date
WARNING!
WARNING!
To reduce risk of death
To reduce risk of death
INJURY HAZARD!
or serious injury, read
or serious injury,Toread
reduce risk of short
manual BEFORE using
long-term injury,
manual BEFOREand
using
machine.
wear safety glasses,
machine.
To get a new manual,
hearing protection, and
call (800) 523-4777 or
To get a new manual,
a respirator when using
go to www.grizzly.com.
call (800) 523-4777
thisor
machine.
MODEL G0814
6" JOINTER w/CABINET STAND
Weight: 245 lbs.
MODEL G0814X
6" JOINTER w/STAND &
V-HELICAL CUTTERHEAD
MODEL G0814X
6" JOINTER w/STAND &
Specifications
V-HELICAL CUTTERHEAD
404
WARNING!
•
• Labels must be made of
oil-resistant material
WARNING!
PANTONE 151 C or RAL 2005
Specifications
MODEL G0814
6 JOINTER w/CABINET STAND
service.
2. Always wear
approved eye protection and respirator.
3. Only plug power cord into a grounded outlet.
4. Except when rabbeting, keep all guards in place and in proper
Cutterhead: 3-Knife,
2-1/2" Dia.
this machine.
Knife Size: 6" x 1" x 1/8"
Maximum Depth of Cut: 1/8"
COLOR CODES
WARNING
•IN
Disc
befo
main
serv
To reduce the risk
of seriousRabbeting
injury whenDepth:
using this
machine:
Maximum
1/2"
operating condition. Always replace guard after rabbeting. ROTATING CUTTER
1. Read & understand owner’s manual before operating.
Cutterhead Speed: 5000 RPM
5. Never cut workpieces smaller than 8" long, 3/4" wide, or 1/2" thick.
2. Always wear approved eye protection and respirator.
Use this guard for all o
Cuts cord
Per into
Minute:
15,000outlet.
6. Always use push blocks when face planing.
3. Only plug power
a grounded
possible, and immedia
Fence
Tilt: keep
45º, all
90º,
135ºin place and in proper 7. Never cut deeper than 1/8" on a single pass.
4. Except when
rabbeting,
guards
operating condition.
Always
guard after rabbeting. ROTATING
Table Size:
47"replace
x 7-1/4"
8. Tie back
long hair, roll up
sleeves, and DO NOT wear loosefollowing operations th
CUTTERHEAD
BELOW!
5. Never cut workpieces
smaller
than
8"
long,
3/4"
wide,
or
1/2"
thick.
Weight: 245 lbs.
clothing,
gloves,
or jewelry.
removal.
Use this
guard for
all operations
6. Always use push blocks when face planing.
9.
Turn
motor
OFF
and
disconnect
power
before
changing
inserts,
possible, and immediately re-install it
7. Never cut deeper than 1/8" on a single pass.
adjusting
tables/fence,
or its
servicing.
8. Tie back long hair, roll up sleeves, and DO NOT wear loosefollowing
operations
that require
10. Before starting, ensure tables are adjusted properly, blades are
clothing, gloves, or jewelry.
removal.
Motor: 1power
HP, 110V/220V,
1-Ph,
60 Hz secure,To
reduce
the
of serious injury when using this machine:
9. Turn motor OFF and disconnect
before changing
inserts,
and
jointer
isrisk
stable.
adjusting tables/fence, or
servicing.Current: 14A at 110V, 7A11.
Full-Load
at 220V
1. Read workpiece
& understand
owner’s
manual
before
operating.
Always support
against
fence
and table.
Never
attempt
KICKBACK H
10. Before starting, ensure Cutterhead:
tables are adjusted
properly, blades are
2. Always wear approved eye protection and respirator.
Date V-Helical w/Indexable Inserts
Motor: 1 HP, 110V/220V, 1-Ph, 60 Hz secure,To
reduce
the
of serious
injury when using this machine:any operation free-handed.
and
jointer
isrisk
stable.
1. Ensure outfeed table
Insert owner’s
Size: 15
x 15 x
2.5mm
3. Only
plug power
cordcutterhead
into a grounded
outlet.
12. Always
feed
workpiece
against
rotation.
Never move
Full-Load Current: 14A at 110V, 7A11.
at 220V
1. Read workpiece
& understand
manual
before
operating.
Always support
against fence
and table.
Never
attempt
KICKBACK
HAZARD!
24and respirator.
4. backward
Except
when
rabbeting,
in proper
Cutterhead:
2. Always
wear Number
approved of
eyeInserts:
protection
workpiece
while
feeding.keep all guards in place andknives.
Date V-Helical w/Indexable Inserts
any operation
free-handed.
S/N
1. Ensure outfeed operating
table is even with
Maximum
of Cut:
1/8" move
Alwaysor
replace
guard
after restrict
rabbeting.
Insert Size: 15 x 15 x 2.5mm
3. Only
plug power
cordcutterhead
intoDepth
a grounded
outlet.
2. Never exceed maxim
12. Always feed
workpiece
against
rotation.
Never
13. Prevent unauthorizedcondition.
use by children
untrained
users;
knives.
Number of Inserts: 24
4.
Except
when
rabbeting,
keep
all
guards
in
place
and
in
proper
Maximum
5. disable
Never cut
workpieces
than 8" long, 3/4" wide,
1/2"stand
thick. directl
workpiece backward
while
feeding. Rabbeting Depth: 1/2"
access or
machine
whensmaller
unattended.
3. Doornot
in Taiwan
Mfd. for Grizzly
S/N
Maximum
Depth of Cut: 1/8"
operating
condition.
Always
replace
guard
after restrict
rabbeting.
2. Never exceed6.maximum
depth
of cut.
13. Prevent unauthorized
use
by children
or
untrained
users;
Cutterhead
Speed:
5000
RPM
Always use
push
blocks when face planing.
Maximum Rabbeting Depth: 1/2"
5. disable
Never cut
workpieces
than 8" long, 3/4" wide,
1/2"stand
thick. directly behind workpiece.
access or
machine
when
unattended.
3. Doornot
Mfd. for Grizzly in Taiwan
Cuts
Persmaller
Minute:
20,000
7. Never cut deeper than 1/8" on a single pass.
Cutterhead Speed: 5000 RPM
6. Always use push blocks when face planing.
Fence
Tilt:
135º
8. Tie back long hair, roll up sleeves, and DO NOT wear loose
Cuts Per Minute: 20,000
7. Never cut deeper
than
1/8"45º,
on a90º,
single
pass.
Size:
47" x 7-1/4"
clothing, gloves, or jewelry.
Fence Tilt: 45º, 90º, 135º
8. Tie back longTable
hair, roll
up sleeves,
and DO NOT wear loose
Table Size: 47" x 7-1/4"
clothing, gloves,
or jewelry.
Weight:
245 lbs.
9. Turn motor OFF and disconnect power before changing inserts,
ALWAYS
USE PU
Weight: 245 lbs.
9. Turn motor OFF and disconnect power before changing inserts,
tables/fence, or servicing.
ALWAYS USEadjusting
PUSH BLOCKS!
adjusting tables/fence, or servicing.
10. Before starting, ensure tables are adjusted properly,
blades
are minimize
Push
blocks
10. Before starting, ensure tables are adjusted properly,
blades
are minimize possibility of
Push
blocks
secure, and jointer is stable.
secure, and jointer is stable.
operator’s hands cont
RSHUDWRU·VKDQGVFRQWDFWLQJFXWWHUKHDG
11. Always support workpiece against fence and table.
Never attempt 11. Always support workpiece against fence and table. Never attempt
Date
while
cutting.
any operation free-handed.
Date
while cutting.
any operation free-handed.
12. Always feed workpiece against cutterhead rotation. Never move 12. Always feed workpiece against cutterhead rotation. Never move
workpiece backward while feeding.
S/N
workpiece backward while feeding.
S/Nor untrained users; restrict
13. Prevent unauthorized use by children
13. Prevent unauthorized use by children or untrained users; restrict
access or disable machine when unattended.
Mfd. for Grizzly in Taiwan
Full-Load
Amp
Draw: 14A
any operation free-handed.
1. Read
& understand
owner’s
manual
before operating.
Cutterhead
Speed: 5000
RPM
5. Never cut workpieces
smaller
than 8" long,
3/4" wide,
or 1/2" thick.
12. Always feed workpiece
against
cutterhead
rotation.
move use push
Cuts Per Cutterhead:
Minute: 15,000
6. Always
when
face
planing. eye protection and respirator.
3-Knife,
2-1/2"Never
Dia.
2. blocks
Always
wear
approved
Fence while
Tilt:
45º,
90º,
135º
7. Never cut deeper
on a
single cord
pass. into a grounded outlet.
workpiece backward
feeding.
Knife
Size:
6" x 1" x 1/8"
3. than
Only1/8"
plug
power
S/N
Table Size:
47"
x 7-1/4" or untrained users;
back long hair, roll up sleeves, and DO NOT wear loose
DANGER
PANTONE 485 C or 13.
RALPrevent
3001 unauthorized
use
by children
restrict
Maximum
Depth of Cut: 1/8" 8. Tie
4. Except when rabbeting, keep all guards in place and in proper
Weight:
245 lbs.
clothing, gloves, or jewelry.
access or disable
machine
when unattended.
Mfd. for Grizzly in Taiwan
Maximum
Rabbeting Depth: 1/2"
operating condition. Always replace guard after rabbeting.
Date
INJURY HAZARD!
To reduce risk of short
and long-term injury,
wear safety glasses,
hearing protection, and
a respirator when using
INJURY/SHOCK
this machine.
HAZARD!
and long-term injury,
Specifications
power
DisconnectWARNING!
MODEL
wear G0814
safety glasses,
adjustments,
Motor: 1 HP, hearing
110V/220V,
1-Ph, 60 Hz
To reduce thebefore
risk of serious
injury when using this machine:
protection,
and
ormanual before operating.
w/CABINET
6 JOINTER
maintenance,
Full-Load Amp
Draw: 14A when STAND
1. Read & understand
owner’s
a respirator
using
Specifications
PANTONE 485 C or RAL 3001
Specifications
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
WARNING!
call (800) 523-4777 or
"
INJURY
goHAZARD!
to www.grizzly.com.
Mfd. for Grizzly in Taiwan
WARNING
PANTONE 151 C or RAL 2005
To reduce the risk of serious injury when using this machine:
1. Read & understand owner’s manual before operating.
2. Always
wear the
approved
eye
protection
and respirator.
To reduce
risk of
serious
injury
when using
this machine: PANTONE 109 C
CAUTION
3. Only
plug power
cord into a grounded
1. Read
& understand
owner’s outlet.
manual before operating.
4. Except when rabbeting, keep all guards in place and in proper
2. Always wear approved eye protection and respirator.
operating condition. Always replace guard after rabbeting.
3.
Only
plug
power
cord
into
a
grounded
outlet.
5. Never cut workpieces smaller than 8" long, 3/4" wide, or 1/2" thick.
4. Except
when
rabbeting,
keep
all guards in place and in proper
6. Always
use push
blocks
when face
planing.
7. Neveroperating
cut deeper condition.
than 1/8" on Always
a single pass.
replace guard after rabbeting.
8. Tie
longcut
hair,
roll up sleeves,
and DO
NOT8"
wear
loose
5.back
Never
workpieces
smaller
than
long,
3/4" wide, or 1/2" thick.
clothing, gloves, or jewelry.
6. Always use push blocks when face planing.
9. Turn motor OFF and disconnect power before changing inserts,
7. Never
cut deeper
than 1/8" on a single pass.
adjusting
tables/fence,
or servicing.
8. Tie
back long
hair,
roll
sleeves,
and DO
NOT
10. Before
starting,
ensure
tables
areup
adjusted
properly,
blades
arewear loose
secure,
and jointer
is stable.
clothing,
gloves,
or jewelry.
1 HP,
110V/220V,
1-Ph,
60attempt
Hz
To inserts,
reduce the risk of serious injury when using this machine:
11. Always
support
workpiece
against
fence
andpower
table.
Never
9. Turn
motor
OFFMotor:
and
disconnect
before
changing
Full-LoadorAmp
Draw: 14A
any operation free-handed.
1. Read & understand owner’s manual before operating.
adjusting tables/fence,
servicing.
12. Always feed workpiece Cutterhead:
against cutterhead
rotation.
3-Knife,
2-1/2"Never
Dia. move
2. Always wear approved eye protection and respirator.
10. Before
starting,
ensure
tables are adjusted properly, blades are
workpiece
backward
while
feeding.
Knife
Size: 6" x 1" x 1/8"
3. Only plug power cord into a grounded outlet.
secure,
and jointer
stable.
13. Prevent
unauthorized
use
byischildren
or untrained
users; restrict
Maximum
Depth
of Cut: 1/8"
4. Except when rabbeting, keep all guards in place and in proper
Motor:
1
HP,
110V/220V,
1-Ph,
60
Hz
To reduce
thereplace
risk of
serious
injury when
access
or disable
machine
when
unattended.
11. Always
support
workpiece
against
fence
and
table.
Never
attempt
Maximum Rabbeting Depth: 1/2"
operating
condition.
Always
guard
after rabbeting.
Specifications
WARNING!
WARNING!
Motor: 1 HP, 110V/220V, 1-Ph, 60 Hz
Full-Load Amp Draw: 14A
Cutterhead: 3-Knife, 2-1/2" Dia.
Knife Size: 6" x 1" x 1/8"
Maximum Depth of Cut: 1/8"
Maximum Rabbeting Depth: 1/2"
Cutterhead Speed: 5000 RPM
Cuts Per Minute: 15,000
Fence Tilt: 45º, 90º, 135º
Table Size: 47" x 7-1/4"
Weight: 245 lbs.
STAND
6" JOINTER w/CABINET
DANGER
PANTONE 485 C or RAL 3001
WARNING!
G0814 Machine Labels (B)
(10/23/15)
MODEL
G0814G0814
MODEL
COLOR CODES
COLOR CODES
6" JOINTER w/CABINET STAND
Failure to keep hands clear
of cutterhead will result in
Use this
guard
operations
Use this
guard
forfor
allalloperations
possible, and immediately re-install it
possible,
and immediately re-install it
following operations that require its
following
operations that require its
removal.
removal.
possible, and immediately re-install it
following operations that require its
ROTATINGremoval.
CUTTERHEAD BELOW!
• Scale: 1:1 (Labels are
actual size)
• Labels must be made of
oil-resistant material
Scale: 1:1 (Labels are
(10/23/15)
G0814 Machine Labels
(B)403• actual
size)
Push blocks minimize the
SRVVLELOLW\RIRSHUDWRU·V
hands contacting the
cutterhead while cutting.
Failure to keep hands clear
of cutterhead will result in
serious personal injury.
Cutterhead
these lines.
exposed between
these lines.
INJURY/SHOCK
HAZARD!
INJURY/SHOCK
power
Disconnect
adjustments,
beforeHAZARD!
Disconnect power
or
maintenance,
before adjustments,
service.
maintenance, or
WARNING!
To reduce risk
of short
and long-term
injury,
INJURY
HAZARD!
To reduce
risk of short
wear safety
glasses,
and long-termand
injury,
hearing protection,
wear safety glasses,
a respirator
when
using
hearing protection, and
this machine.
a respirator when using
service.
Do not operate machine
even with knives.
with guard removed!
2. Never exceed the
Cutterhead contact
will
maximum depth
of cut.
ROTATING
CUTTERHEAD
BELOW!
cause serious personal
3. forDo
stand directly
Use this guard
allnot
operations
injury.
behind workpiece.
G0814 Machine Labels (B)
ALWAYS USE
PUSH BLOCKS!
WARNING!
Failure to keep hands clear
of cutterhead will result in
serious personal injury.
of cutterhead will result in
serious personal injury.
411
Failure to keep hands clear
of cutterhead will result in
serious
personal
injury.
Failure
to keep
hands clear
• Labels must be madethis
ofmachine.
oil-resistant material
personal
Failureserious
to keep
handsinjury.
clear
of cutterhead will result in
serious personal injury.
go to www.grizzly.com.
WARNING!
INJURY HAZARD!
2.
(10/23/15)
Push blocks minimize the
possibility of operator’s
hands contacting the
cutterhead while cutting.
WARNING!
KICKBACK HAZARD!
Cutterhead
exposed between
these lines.
WARNING!
(10/23/15)
G0814 Machine Labels (B)
educe risk of death
erious injury, read
WARNING!
ual BEFORE
To using
reduce risk of death
hine.
or serious injury, read
manual BEFORE using
et a new manual,
machine.
800) 523-4777 or
To get a new manual,
o www.grizzly.com.
call (800) 523-4777 or
3.
Ensure outfeed table is
even with knives.
Never exceed the
maximum depth of cut.
Do not stand directly
behind workpiece.
G0814 Machine Labels (B)
WARNING!
ALWAYS USE
PUSH BLOCKS!
KICKBACK HAZARD!
cutterhead while cutting.
injury.
behind workpiece.
To reduce risk of death
INJURY HAZARD!
INJURY/SHOCK
DANGER!
or serious injury, read
To reduce risk of short
HAZARD!
ROTATING
manual BEFORE using
and long-termCUTTERHEAD
injury,
BELOW!
machine.
power
Disconnect
• Scale: 1:1 (Labels arewear safety glasses,
To get a new manual,
before adjustments,
ALWAYS USE
KICKBACK HAZARD!
hearing protection, and
WARNING!
actual
size)
WARNING!
call (800)
523-4777
or
or
maintenance,
a respirator when using
1. Ensure
outfeed table is
PUSH BLOCKS!
Toto
reduce
risk of death
go
service.
Do not operate
machine
INJURY
INJURY/SHOCK
this
machine.
even with knives.
•www.grizzly.com.
Labels
must be made
ofHAZARD!
or serious
injury, read
Push blocks minimize the
To reduce risk of short
with guard removed!
HAZARD!
2. Never exceed the
manual BEFORE using
possibility of operator’s
and long-term injury,
oil-resistant material
WARNING!
WARNING!
machine.
Cutterhead
contact
will
power
Disconnect
maximum
depth
of
cut.
• Scale: 1:1 (Labels arewear safety glasses,
hands contacting the
To get a new manual,
before adjustments,
cause serious
personal
3. Do not standALWAYS
directly USE
KICKBACK HAZARD!
hearing protection, and
actual
size)
call (800)
523-4777
or
or
injury. maintenance,
a respirator when using
1. Ensure
outfeed table
is workpiece.
PUSH BLOCKS!cutterhead while cutting.
behind
0814 Machine Labels
(B)
412
WARNING!
2.
WARNING!
1.
WARNING!
1.
Do not operate machine
with guard removed!
Cutterhead contact will
cause serious personal
injury.
Failure to keep hands clear
CUTTERHEAD BELOW!
actual size)
• Labels must be made of
oil-resistant material
INJURY HAZARD!
To reduce risk of short
and long-term injury,
wear safety glasses,
hearing protection, and
a respirator when using
this machine.
Failure to keep hands clear
(10/23/15)
Failure to keep hands clear
of cutterhead will result in
serious personal injury.
Failure to keep hands clear
go to www.grizzly.com.
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
Cutterhead
Failure to keep hands clear
exposed between
DANGER!
of cutterhead
will result in
Scale: 1:1 (Labels
are
ROTATING
these• lines.
serious personal injury.
of cutterhead will result in
G0814 Machine
(B)
serious personal Labels
injury.
(10/23/15)
WARNING!
Failure to keep hands clear
of cutterhead will result in
serious personal injury.
Cutterhead
401
WARNING!
Failure to keep hands clear
of cutterhead will result in
personal injury.
Cutterhead
serious
exposed between
these lines.
Failure to keep hands clear
of cutterhead will result in
serious personal injury.
Cutterhead
exposed between
these lines.
Cutterhead
exposed between
these lines.
Failure to keep hands clear
of cutterhead will result in
serious personal injury.
Failure to keep hands clear
of cutterhead will result in
serious personal injury.
Cutterhead
exposed between
these lines.
Failure to keep hands clear
of cutterhead will result in
serious personal injury.
Failure to keep hands clear
of cutterhead will result in
serious personal injury.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
COLO
DANGER
WARNING
CAUTION
WARRANTY & RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
In the event you need to use this warranty, contact us by mail or phone and give us all the details. We will
then issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of
the carton. We will not accept any item back without this number. Proof of purchase must accompany the
merchandise.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
To take advantage of this warranty, you must register it at https://www.grizzly.com/secureforms/
warranty-card, or you can scan the QR code below to be automatically directed to our warranty
registration page. Enter all applicable information for the product.
WARRANTY
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement