Grizzly H3114 Router Table On Stand Owner Manual

Grizzly H3114 Router Table On Stand Owner Manual

ROUTER TABLE MODEL H3114 INSTRUCTION MANUAL

COPYRIGHT © DECEMBER 2002 BY GRIZZLY INDUSTRIAL, INC

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

PRINTED IN CHINA

ONLINE MANUAL DISCLAIMER

THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CURRENTLY BEING SHIPPED. THE MACHINE CONFIGURATION CAN CHANGE AS PRODUCT IMPROVEMENTS ARE INCORPORATED. IF YOU OWN AN EARLIER VERSION OF THE MACHINE, THIS MANUAL MAY NOT EXACTLY DEPICT YOUR MACHINE . CONTACT CUSTOMER SERVICE IF YOU HAVE ANY QUESTIONS ABOUT DIFFERENCES. PREVIOUS VERSIONS ARE NOT AVAILABLE ONLINE.

WARNING

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemi cals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints.

• Crystalline silica from bricks, cement, and other masonry products.

• Arsenic and chromium from chemically treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

2.

3.

1.

4.

TABLE OF CONTENTS

PAGE SAFETY ......................................................................................................................................................2

SAFETY INSTRUCTIONS FOR POWER TOOLS............................................................................2-3 ADDITIONAL SAFETY INSTRUCTIONS FOR ROUTER TABLES ....................................................4

INTRODUCTION ........................................................................................................................................5

COMMENTARY....................................................................................................................................5

CIRCUIT REQUIREMENTS ........................................................................................................................6

GENERAL ............................................................................................................................................6

ELECTRICAL ......................................................................................................................................6

SET UP........................................................................................................................................................7

MAIN FEATURES ................................................................................................................................7

ASSEMBLY ....................................................................................................................................8-13 OPERATION ................................................................................................................................14-16

REFERENCE INFO ..................................................................................................................................17

5.

PARTS BREAKDOWNS AND LIST ..................................................................................................................18-19 WARRANTY AND RETURNS ..........................................................................................................................22-24

SECTION 1: SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury, or MAY cause property damage.

NOTICE

This symbol is used to alert the user to useful information about proper operation of the equipment.

-2-

Safety Instructions For Power Tools

1. KEEP GUARDS IN PLACE

order.

and in working

5.

KEEP CHILDREN AND VISITORS AWAY.

All children and visitors should be kept at a safe distance from work area.

2. REMOVE ADJUSTING KEYS AND WRENCHES.

Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning on.

6. MAKE WORKSHOP CHILD PROOF

with padlocks, master switches, or by removing starter keys.

3. KEEP WORK AREA CLEAN.

Cluttered areas and benches invite accidents.

4. DO NOT USE IN DANGEROUS ENVI RONMENT.

Do not use power tools in damp or wet locations, or where any flam mable or noxious fumes may exist. Keep work area well lighted.

7. DO NOT FORCE TOOL.

It will do the job better and safer at the rate for which it was designed.

8. USE RIGHT TOOL.

Do not force tool or attachment to do a job for which it was not designed.

H3114 Router Table

Safety Instructions For Power Tools

9.

USE PROPER EXTENSION CORD

. Make sure your extension cord is in good condi tion. Conductor size must be in accor dance with the chart below. The amperage rating is listed on the motor or tool name plate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension cord must also contain a ground wire and plug pin. Always repair or replace damaged extension cords.

Minimum Gauge for Extension Cords LENGTH AMP RATING 25ft 50ft 100ft

0-6 7-10 11-12 13-16 17-20 21-30 18 18 16 14 12 10 16 16 16 12 12 10 16 14 14 12 10 No

10. WEAR PROPER APPAREL.

Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair.

11. ALWAYS USE ANSI-APPROVED SAFE TY GLASSES.

Also use face or dust mask if cutting operation is dusty. Everyday eye glasses only have impact resistant lenses, they are NOT safety glasses.

12. SECURE WORK.

Use clamps or a vise to hold work when practical. It is safer than using your hand and frees both hands to operate tool.

13. NEVER OVERREACH.

Keep proper foot ing and balance at all times.

14. MAINTAIN TOOLS WITH CARE.

Keep tools sharp and clean for best and safest performance. Follow instructions for lubri cating and changing accessories.

15. DISCONNECT TOOLS

before servicing and changing accessories, such as blades, bits, cutters, and any other item.

16. REDUCE THE RISK OF UNINTENTIONAL STARTING.

Make sure switch is in off posi tion before plugging in. Also, the magnetic switch on this machine may start if the switch gets bumped hard enough.

17. USE RECOMMENDED ACCESSORIES.

Consult the owner’s manual for recom mended accessories. The use of improper accessories may cause risk of injury.

18. CHECK DAMAGED PARTS.

Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of mov ing parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is dam aged must be properly repaired or replaced.

19. NEVER LEAVE TOOL RUNNING UNAT TENDED. TURN POWER OFF.

Do not leave tool until it comes to a complete stop.

20. NEVER USE UNDER THE INFLUENCE

of alcohol or drugs, or when tired.

21. IF AT ANY TIME YOU ARE EXPERIENC ING DIFFICULTIES

performing the intend ed operation, stop using the machine! Then contact our service department or ask a qualified expert how the operation should be performed.

H3114 Router Table -3-

Additional Safety Instructions For Router Tables

1.

HAND POSITIONING.

Never pass your hands directly over, or in front of the cutter. As one hand approaches cutter, move it in an arc motion away from the cutter to the outfeed side and reposition that hand beyond the cut ter.

We recommend using some type of fixture, jig, or hold-down device as a safer alterna tive. Use a guard or other type of protective device at all times.

8.

ALWAYS FEED AGAINST THE ROTA TION OF THE CUTTER.

2.

STOCK LENGTH.

Do not shape stock short er than 12 inches without special fixtures or jigs. Where practical, shape longer stock and cut to size.

9.

DO NOT REMOVE THE RETRACTABLE GUARD ON THE FENCE.

3.

BLIND CUT WHENEVER POSSIBLE.

This keeps the cutters on the underside of the workpiece and provides a distance guard for the operator.

10. IF AT ANYTIME YOU ARE EXPERIENC ING DIFFICULTIES PERFORMING THE INTENDED OPERATION, STOP USING THE ROUTER TABLE!

Then contact our service department or ask a qualified expert how the operation should be performed.

4.

TEST ROTATION.

Always rotate the spindle by hand, with the machine unplugged, to test any new setup to ensure proper cutter clear ance before starting the machine.

5.

KEEP ANY UNUSED PORTION OF THE CUTTER BELOW THE TABLE SURFACE.

11. BE AWARE THAT CERTAIN WOODS MAY CAUSE AN ALLERGIC REACTION

in people and animals, especially when exposed to fine dust. Make sure you know what type of wood dust you will be exposed to, the possibility of a allergic reaction and always wear an approved respirator.

6.

DEPTH OF CUT.

Never remove too much material in one pass. Several light passes are safer and give a cleaner finish.

12. NEVER REACH BEHIND THE SPINNING CUTTER.

7.

SAFETY DEVICES.

The use of push sticks as safety devices in some applications is smart; in others it can be quite dangerous. If the push stick comes in contact with the cut ter on the end grain, it can fly out of your hand like a bullet—potentially causing serious injury.

13. READ AND UNDERSTAND THE INSTRUCTION MANUAL SUPPLIED WITH THE ROUTER INSTALLED IN THIS TABLE 14. DO NOT REACH UNDER THE ROUTER TABLE WHILE THE ROUTER IS PLUGGED IN OR RUNNING.

-4 H3114 Router Table

SECTION 2: INTRODUCTION Commentary

We are proud to offer the Grizzly Model H3114 Router Table. The Model H3114 is part of a grow ing Grizzly family of fine woodworking machinery.

When used according to the guidelines set forth in this manual, you can expect years of trouble free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction.

Features include: • Over 440 square inches of work surface • Master power switch controls a router and another accessory such as a shop vac • Universal clamping system allows the mount ing of most brands of routers • Heavy-duty fence system with dust port • Pocket jointing fence allows router table to function as a jointer • Miter gauge • Various table inserts • Convenient fence scales allow for precise adjustment • Retractable safety guard • Heavy-duty cast aluminum table Grizzly is also pleased to provide this manual with the Model H3114. It was written to guide you through assembly, review safety considerations, and cover general operating procedures. If you have any comments regarding this manual, please write to us at the address below: Grizzly Industrial, Inc.

C / O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 Most importantly, we stand behind our machines.

If you have any service questions or parts requests, please call or write us at the location listed below: Grizzly Industrial, Inc.

1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663 Fax: (800) 438-5901 E-Mail: techsupport@grizzly.com

Web Site: http://www.grizzly.com

The specifications, drawings, and photographs illustrated in this manual represent the Model H3114 as supplied when the manual was pre pared. However, owing to Grizzly’s policy of con tinuous improvement, changes may be made at any time with no obligation on the part of Grizzly.

Current Grizzly machine manuals can be viewed and printed at: www.grizzly.com.

Lack of familiarity with this manual could cause serious person al injury. Become familiar with the con tents of this manual, including all the safety warnings.

H3114 Router Table -5-

SECTION 3: CIRCUIT REQUIREMENTS General

If the machine is wired incorrectly a fire could result. Make sure your wiring, recep tacle, plug, and circuit breaker can handle the current draw of the machine. If you are not sure that your electrical circuit can han dle the current draw, get a qualified electri cian to test your electrical system and do any required upgrades. Do not attempt to modify an existing circuit by only replacing the circuit breaker with one rated for a high er amperage draw than the wiring, recepta cle, and plug are rated for.

The power switch (

Page 7, Figure 2

) on the Model H3114 is designed to work with most routers and other electrical accessories. The power switch provides the convenience of switch ing power to the router and accessories at the front of the router table instead of having to reach under the table and locate multiple switches. The power switch also allows multiple devices such as lights or vacuums to be powered on when the router is powered on.

Electrical

The Model H3114 power switch is designed to accept 2-prong DOUBLE INSULATED plugs or 3 prong grounding type plugs. The power switch plugs into a wall outlet that is properly grounded as shown in

Figure 1

.

Grounded Outlet Grounding Prong Current Carrying Prongs

Figure 1.

Power switch 3-prong plug and grounding style outlet.

-6 H3114 Router Table

SECTION 4: SET UP Main Features

Set up and operation instructions will be easier to understand if you become familiar with the location and names of the basic features shown in

Figure 2

.

Extension Table Pocket Jointing Fence Retractable Guard Dust Port Table Insert Main Fence Leg Main Table Power Switch

Note–Only 1 of the 5 table inserts are shown.

Figure 2.

Machine features.

Miter Gauge H3114 Router Table -7-

-8-

!

Assembly

Loose hair and clothing could get caught in machinery causing seri ous personal injury.

Keep loose clothing rolled up and long hair tied up and away from machinery.

To attach the extension tables and legs to the main table: 1.

Place the main table upside down on a work bench.

2.

Align the extension tables mounting holes with the mounting holes on the edge of the main table (

Figure 3

).

Note—DO NOT secure the extension tables with screws at this time.

Extension Table

Disconnect power to the machine during the entire assembly process.

Failure to do this may result in serious person al injury.

Main Table

Figure 3.

Aligning an extension table with the main table.

Projectiles thrown from the machine could cause serious eye injury. Wear safety glasses during assembly.

Sharp edges on metal parts may cause person al injury. Examine the edges of all metal parts before handling.

H3114 Router Table

3.

Align one of the legs with the mounting holes on the inside edge of the main table as shown in

Figure 4

.

To check the flushness of the table: 1.

Place a straightedge across both extension tables and the main table. The straightedge should sit flush on all three surfaces as shown in

Figure 6

.

Figure 4.

Aligning a leg with the main table.

4.

Secure the leg and extension table to the main table with the supplied #10-32 x 3 ⁄ 4 " truss head phillips screws and the #10-32 keps nuts as shown in

Figure 5

.

Figure 6.

Using a straightedge to ensure the working surfaces are flush.

2.

If either extension table is not flush with the main table, loosen the mounting screws and adjust the assembly until both extension tables and the main table are flush with one another.

3.

Retighten the mounting screws.

4.

Double check the the flushness of the work ing surface with the straightedge.

Figure 5.

Securing a leg to the main table.

5.

Repeat

Steps 3 & 4

legs.

for the remaining three H3114 Router Table -9-

To mount the router to the table:

The base plate mounting holes on some brands of routers may align with the router mounting holes on the main table. If the holes line up, con tinue with

Method 1

. If the holes do not line up, skip ahead to

Method 2

.

Method 1 1.

Remove the base plate from the router base by removing the three base plate screws.

Note—The router base plate is usually a cir cular black plastic plate that is screwed to the router base.

2.

Turn the router upside down and hold the router base against the circular recess in the underside of the main table as shown in

Figure 7

.

Circular Recess

Method 2 1.

Remove the base plate from the router base.

Note–The bottom face of the router base must form a continuous ring with no gaps. If the router base does not have this design, DO NOT remove the base plate.

2.

Turn the router table upside down.

3.

Insert the supplied M5-0.8 x 45 carriage bolts through the four large mounting holes in the top of the main table.

4.

Slide the four clamps over the ends of the carriage bolts with the tabs facing the under side of the main table as shown in

Figure 8

.

Clamps

3.

Figure 7.

Router positioned correctly for "Method 1" installation.

Rotate the router until the main table mount ing holes align with the mounting holes in the router base.

Note—Orient the router so the adjustment controls are easy to reach.

4.

With the three screws removed in

Step 1

, secure the router to the underside of the main table.

Figure 8.

Clamps for securing “

Method 2

” style routers to the main table.

5.

Begin threading the M5-0.8 keps nuts onto the ends of the M5-0.8 x 45 carriage bolts.

6.

Rotate the clamps out of the circular recess and position the router base against the cir cular recessed area. -10 H3114 Router Table

7.

Hold the router and rotate the clamps over the router base as shown in

Figure 9

.

To assemble the fence: 1.

Attach the spring to the retractable guard as shown in

Figure 11

.

Retractable Guard Spring Clamp Position

8.

Figure 9.

Rotating a clamp over the router base.

Tighten the M5-0.8 keps nuts enough to pre vent the router from moving, but DO NOT fully tighten them at this time.

9.

Turn the router table top-side up.

10.

Loosen the M5-0.8 keps nuts several turns and reposition the router until the router spin dle is centered in the round table cut-out when viewed from above.

11.

Tighten the M5-0.8 keps nuts (

Figure 10

).

2.

Figure 11.

Correct spring placement.

Insert the retractable guard into the fence and secure the guard with the supplied M4 x 12 tap screw and the M5 flat washer (

Figure 12

).

The bit guard should move freely with no binding on the fence. If binding occurs, light ly sand or file the contact areas.

Figure 12.

Correctly installed guard.

Figure 10.

Correctly clamped router.

H3114 Router Table -11-

3.

Slide the pocket jointing fence into the slot in the face of the main fence as shown in

Figure 13

.

To attach the power switch to the main table: 1.

Secure the power switch to the main table with the supplied #10-32 x 3 ⁄ 4 " truss head phillips screws and the #10-32 keps nuts as shown in

Figure 15

.

Note—The power switch mounting bracket should be on the inside of the main table edge.

4.

Figure 13.

Installing the pocket jointing fence.

Secure the pocket jointing fence to the main fence with the supplied M8-1.0 x 20 hex bolt and the M8-1.0 threaded knob.

5.

Place the fence assembly on the main table.

6.

Align the slots on the fence assembly over the slots on the table surface.

7.

Secure the fence assembly to the table with the supplied M8-1.0 x 40 hex bolts and the M8-1.0 threaded knobs as shown in

Figure 14

.

2.

Figure 15.

Securing the power switch to the main table.

Flip the table assembly top-side up

.

Figure 14.

Securing the fence to the main table.

-12 H3114 Router Table

To secure the router table to a workbench:

The bottom of each leg has two holes (

Figure 16

) used for mounting the router table to the work bench. Secure the router table to the workbench with wood screws and washers.

To assemble the miter gauge (Figure 17 & 18): 1.

Attach the miter body to the miter bar with the supplied M4 x 12 tap screw.

2.

Place the M8 flat washer over the M8-1.0 x 12 knob bolt.

3.

Slide the M8-1.0 x 12 knob bolt through the miter body slot and thread it into the miter bar.

Miter Body Tap Screw Miter Bar

Figure 16.

Router table mounting holes.

Flat Washer Knob Bolt

Figure 17.

Miter gauge components.

H3114 Router Table

Figure 18.

Assembled miter gauge.

-13-

Operation

Loose hair and clothing could get caught in machinery causing seri ous personal injury.

Keep loose clothing rolled up and long hair tied up and away from machinery.

4.

Loosen the threaded knob on the pocket jointing fence and slide the pocket jointing fence from the main fence to the desired depth of cut (

Figure 19

). Tighten the thread ed knob when adjusted correctly.

Note–The face of the pocket jointing fence must be par allel to the main fence face before performing any routing operations.

Pocket Jointing Fence Main Fence

Projectiles thrown from the machine could cause serious eye injury. Wear safety glasses during assembly.

Routing operations on your Model H3114 are grouped into three main techniques:

• Jointing an edge (Page 14) • Groove cutting (Page 15) • Profile cutting with pilot bits (Page 16) Jointing an edge:

Jointing the edge of a board involves using a straight cutting router bit to remove wood from the edge face of a board. The result is a perfectly flat and square edge used as the glue edge when gluing multiple boards together to form a larger panel.

1.

Secure a straight cutting router bit into your router according to the router manufacturer’s instructions.

2.

Snap one of the table inserts into the recessed hole on the table. Use the insert with the smallest hole that still allows the bit free rotation.

3.

Raise the bit to a height equal to that of the thickness of your board.

-14 Depth Of Cut Threaded Knob Router Bit

5.

Figure 19.

Proper setup for jointing an edge.

Loosen the threaded knobs that secure the main fence.

6.

Place a straightedge across the entire face of the pocket jointing fence and adjust the main fence until the outside diameter of the router bit just touches the straightedge (

Figure 20

).

Straightedge Contact Across Entire Pocket Jointing Fence Face Just Touches Here

Figure 20.

Use a straightedge to properly adjust the main fence.

7.

Tighten the main fence threaded knobs.

8.

Double check that the router is secured to the table. If it is, the router table is ready for use.

H3114 Router Table

Groove cutting:

Beading is commonly defined as cutting a groove or bead in the face of a board.

1.

Mount a router bit into your router according to the router manufacturer’s instructions.

2.

Snap one of the table inserts into the recessed hole on the table. Use the insert with the smallest hole that still allows the bit free rotation.

3.

Raise the bit to the desired height.

4.

Loosen the threaded knobs that secure the main fence.

5.

Adjust the main fence until the center of the V-groove bit is the desired distance away as shown in

Figure 21 & 22

. Distance From Edge Of Board To Center Of V-Groove

Figure 22.

Groove cutting setup.

(Side View)

6.

Tighten the main fence threaded knobs.

7.

Double check that the router is secured to the table. If it is, the router table is ready for use.

Distance From Edge Of Board To Center Of V-Groove

Figure 21.

Groove cutting setup.

(Top View) H3114 Router Table -15-

Profile cutting with pilot bits:

Router bits with ball bearings are called pilot bits.

The ball bearing is used to control the depth of cut into the edge face of a board. A good example would be a chamfer cut. The bearing rides along the uncut edge of the board while the cutter removes the wood.

1.

Mount a router bit into your router according to the router manufacturer’s instructions.

2.

Snap one of the table inserts into the recessed hole on the table. Use the insert with the smallest hole that still allows the bit free rotation.

3.

Raise the bit to the desired height.

4.

Loosen the threaded knobs that secure the main fence.

5.

Adjust the fence back away from the bit only enough to allow the bearing to control the depth of cut as shown in

Figure 23 & 24

.

6.

Adjust the fence as close as possible to the bearing. The fence will serve as a back-up support, reducing the chance of an accident.

Router Bit Ball Bearing

Figure 24.

Proper setup for profile cutting.

(Side View)

7.

Tighten the main fence threaded knobs.

8.

Double check that the router is secured to the table. If it is, the router table is ready for use.

Ball Bearing Router Bit

Figure 23.

Proper setup for profile cutting.

(Top View) -16 H3114 Router Table

SECTION 5: REFERENCE INFO

If you need parts or help in assembling your machine, or if you need operational information, call the Grizzly Service Department. Trained ser vice technicians will be glad to help you.

If you have any comments regarding this manual, please write to Grizzly at the address below: Grizzly Industrial, Inc.

C / O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 Important safety measures that are essential to the operation of this machine have been explained in

Section 1: Safety

. While most safety measures are generally universal, Grizzly reminds you that each workshop is different and safety rules should be considered as they apply to your specific situation.

We recommend you keep a copy of our current catalog for complete information regarding Grizzly's warranty and return policy. If you need additional technical information relating to this machine, or if you need general assistance or replacement parts, please contact the Service Department at the location listed below.

Grizzly Industrial, Inc.

1203 Lycoming Circle Muncy, PA 17756 Phone: (570) 546-9663 Fax: (800) 438-5901 E-Mail: techsupport@grizzly.com

Web Site: http://www.grizzly.com

.

Additional information sources are necessary to realize the full potential of this machine. Trade journals, woodworking magazines, and your local library are good places to start. H3114 Router Table -17-

-18-

PARTS BREAKDOWN AND LIST

28 13 12 11 10 27 15 8 8 16 17 18 19 20 21 22 24 23 26 25 5 3 2 1 H3114 Router Table

REF PART # DESCRIPTION

1 2 3 5 PH3114001 EXTENSION TABLE PH3114002 LEG PH3114003 MAIN TABLE PH3114005 MITER BODY 6 8 PH3114006 SWITCH PS40 #10-32 x 3/4" TRUSS HD PHLP SCR 10 PN29 11 PB09M #10-32 HEX NUT (KEPS) M8-1.25 x 20 HEX BOLT 12 PH3114012 POCKET JOINTING FENCE 13 PH3114013 MAIN FENCE 15 PH3114015 M8-1.25 THREADED KNOB 16 PH3114016 DUST COLLECTION INSERT

REF PART # DESCRIPTION

17 PH3114017 SAFETY GUARD 18 PHTEK5M M4 X 12 (TYPE B) TAP SCREW 19 PH3114019 TABLE INSERT (5) 20 PH3114020 SPRING 21 PW02M M5 FLAT WASHER 22 PH3114022 23 PW09M M8-1.25 x 12 KNOB BOLT M7 FLAT WASHER 24 PH3114024 MITER BAR 25 PCB05M M5-0.8 X 45 CARRIAGE BOLT 26 PH3114026 CLAMPS 27 PH3114027 LOGO (LARGE) 28 PH3114028 LOGO (SMALL) H3114 Router Table -19-

NOTES

-20 H3114 Router Table

NOTES

H3114 Router Table -21-

WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of

1 year

to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any par ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.

In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, spe cial, or consequential damages arising from the use of our products.

To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the car ton. We will not accept any item back without this number. Proof of purchase must accompany the mer chandise. The manufacturers reserve the right to change specifications at any time because they constantly strive to achieve better quality equipment. We make every effort to ensure that our products meet high quality and durability standards and we hope you never need to use this warranty.

Please feel free to write or call us if you have any questions about the machine or the manual. Thank you again for your business and continued support. We hope to serve you again soon.

-22 H3114 Router Table

WARRANTY CARD

Name Street ____________________________________________________________________________________ ____________________________________________________________________________________ City ______________________________________________________________State________Zip_________ Phone Number_______________________E-Mail_______________________FAX________________________ MODEL #_______________ Order #___________________ Serial #__________________________________

The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of course, all information is strictly confidential.

1.

How did you learn about us?

9.

How many of your woodworking machines are Grizzly? _____________ ___Advertisement ___Catalog ___World Wide Web ___Friend ___Card Deck 10.

Which benchtop tools do you own? Check all that apply.

2.

3.

4.

5.

6.

___Other__________________________________________________ Which of the following magazines do you subscribe to.

___American Woodworker ___Cabinetmaker ___Family Handyman ___Fine Homebuilding ___Fine Woodworking ___Home Handyman ___Journal of Light Construction ___Old House Journal ___Popular Mechanics ___Popular Science ___Popular Woodworking ___Other__________________________________________________ Which of the following woodworking/remodeling shows do you watch?

___Backyard America ___Home Time ___The American Woodworker ___Other__________________________________________________ What is your annual household income?

___$20,000-$29,999 ___$30,000-$39,999 ___$40,000-$49,999 ___$50,000-$59,999 What is your age group?

___20-29 ___30-39 ___40-49 ___0 - 2 Years ___2 - 8 Years ___Practical Homeowner ___Shop Notes ___Today’s Homeowner ___WOOD ___Wooden Boat ___Woodshop News ___Woodsmith ___Woodwork ___Woodworker ___Woodworker’s Journal ___Workbench ___The New Yankee Workshop ___This Old House ___Woodwright’s Shop ___$60,000-$69,999 ___$70,000-$79,999 ___$80,000-$89,999 ___$90,000 + ___50-59 ___60-69 ___70 + How long have you been a woodworker?

___8 - 20 Years ___20+ Years 11.

12.

13.

14.

15.

16.

___1" x 42" Belt Sander ___5" - 8" Drill Press ___8" Table Saw ___8" - 10" Bandsaw ___Disc/Belt Sander ___Mini Jointer ___6" - 8" Grinder ___Mini Lathe ___10" - 12" Thickness Planer ___Scroll Saw ___Spindle/Belt Sander ___Other__________________________________________________ How many of the machines checked above are Grizzly? ____________ Which portable/hand held power tools do you own? Check all that apply.

___Belt Sander ___Biscuit Joiner ___Circular Saw ___Detail Sander ___Drill/Driver ___Miter Saw ___Other__________________________________________________ What machines/supplies would you like Grizzly Industrial to carry?

__________________________________________________________ __________________________________________________________ What new accessories would you like Grizzly Industrial to carry?

__________________________________________________________ __________________________________________________________ What other companies do you purchase your tools and supplies from?

__________________________________________________________ __________________________________________________________ Do you think your purchase represents good value?

___Yes ___Orbital Sander ___Palm Sander ___Portable Planer ___Saber Saw ___Reciprocating Saw ___Router ___No 7.

8.

How would you rank your woodworking skills?

___Simple ___Intermediate ___Advanced ___Master Craftsman 17.

18.

Would you recommend Grizzly Industrial to a friend?

___Yes ___No Would you allow us to use your name as a reference for Grizzly customers in your area?

Note: We never use names more than three times.

___Yes ___No What stationary woodworking tools do you own? Check all that apply.

___Air Compressor ___Band Saw ___Drill Press ___Drum Sander ___Dust Collector ___Horizontal Boring Machine ___Jointer ___Lathe ___Mortiser ___Panel Saw ___Planer ___Power Feeder ___Radial Arm Saw ___Shaper ___Spindle Sander ___Table Saw ___Vacuum Veneer Press ___Wide Belt Sander ___Other__________________________________________________ 19.

Comments:_________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________

FOLD ALONG DOTTED LINE

GRIZZLY INDUSTRIAL, INC.

P.O. BOX 2069 BELLINGHAM, WA 98227-2069

FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here

Buy Direct and Save with Grizzly

®

– Trusted, Proven and a Great Value!

Visit Our Website Today And Discover Why Grizzly

®

Is The Industry Leader!

SECURE ORDERING

ORDERS SHIPPED WITHIN 24 HOURS

E-MAIL RESPONSE WITHIN ONE HOUR

-OR-

Call Today For A

FREE

Full Color Catalog

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement